Re: Mainline Debian on Iomega ix4-300d September 09, 2023 05:08PM |
Admin Registered: 13 years ago Posts: 18,821 |
alf45tar
Re: Mainline Debian on Iomega ix4-300d September 10, 2023 04:14AM |
Marvell>> ide reset; ext2load ide 2:1 0x0040000 uImage; ext2load ide 2:1 0x2000000 uInitrd; setenv bootargs $console $mtdparts root=LABEL=rootfs rw rootdelay=5; bootm 0x40000 0x2000000 Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found Found adapter at bus 0, device 1 ... Scanning channels Device 2 @ 1 0: Model: WDC WD800JD-75MSA3 Firm: 10.01E04 Ser#: WD-WMAM9CF02972 Type: Hard Disk Supports 48-bit addressing Capacity: 76293.9 MB = 74.5 GB (156250000 x 512) Device 3 @ 1 1: Model: WDC WD5000AZLX-75K2TA0 Firm: 01.01A01 Ser#: WD-WCC6Z6NZ16LL Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) Device 4 @ 1 2: Model: WDC WD5000AAKS-00A7B0 Firm: 01.03B01 Ser#: WD-WMASY4625414 Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) Loading file "uImage" from ide device 2:1 (hdc1) 5137175 bytes read Loading file "uInitrd" from ide device 2:1 (hdc1) 10142870 bytes read ## Booting kernel from Legacy Image at 00040000 ... Image Name: Linux-6.4.11-mvebu-tld-1 Created: 2023-09-09 15:54:47 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5137111 Bytes = 4.9 MB Load Address: 04000000 Entry Point: 04000000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02000000 ... Image Name: initramfs-6.4.11-mvebu-tld-1 Created: 2023-09-09 15:56:22 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 10142806 Bytes = 9.7 MB Load Address: 02000000 Entry Point: 02000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 6.4.11-mvebu-tld-1 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Sun Aug 20 03:17:26 PDT 2023 [ 0.000000][ T0] CPU: ARMv7 Processor [562f5842] revision 2 (ARMv7), cr=10c5387d [ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Lenovo Iomega ix4-300d [ 0.000000][ T0] Memory policy: Data cache writealloc [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] HighMem empty [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] percpu: Embedded 14 pages/cpu s25300 r8192 d23852 u57344 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 mtdparts=armada-nand:0xe0000@0x0(uboot),0x20000@0xe0000(env),0x20000@0x100000(env2),0x400000@0x120000(zImage),0x400000@0x520000(initrd),0x3F200000@0xE00000(boot),0x40000000@0x0(flash) root=LABEL=rootfs rw rootdelay=5 [ 0.000000][ T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 129920 [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 490396K/524288K available (10240K kernel code, 867K rwdata, 3444K rodata, 1024K init, 462K bss, 33892K reserved, 0K cma-reserved, 0K highmem) [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x1a696b10 -> 0x1a696b12 [ 0.000000][ T0] Aurora cache controller enabled, 16 ways, 1024 kB [ 0.000000][ T0] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a696b12 [ 0.000000][ T0] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000][ T0] Switching to timer-based delay loop, resolution 40ns [ 0.000001][ T0] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns [ 0.000015][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.000684][ T0] kfence: initialized - using 2097152 bytes for 255 objects at 0x(ptrval)-0x(ptrval) [ 0.001598][ T0] Console: colour dummy device 80x30 [ 0.001638][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000) [ 0.001652][ T0] CPU: Testing write buffer coherency: ok [ 0.001693][ T0] pid_max: default: 32768 minimum: 301 [ 0.002061][ T0] LSM: initializing lsm=capability,integrity [ 0.002272][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.002287][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.003845][ T1] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.005247][ T1] cblist_init_generic: Setting adjustable number of callback queues. [ 0.005255][ T1] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.005381][ T1] cblist_init_generic: Setting adjustable number of callback queues. [ 0.005388][ T1] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.005560][ T1] Setting up static identity map for 0x100000 - 0x100060 [ 0.005896][ T1] mvebu-soc-id: MVEBU SoC ID=0x7823, Rev=0x1 [ 0.006021][ T1] mvebu-pmsu: Initializing Power Management Service Unit [ 0.006191][ T1] rcu: Hierarchical SRCU implementation. [ 0.006198][ T1] rcu: Max phase no-delay instances is 1000. [ 0.007188][ T1] smp: Bringing up secondary CPUs ... [ 0.008027][ T1] Booting CPU 1 [ 0.008382][ T0] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.018454][ T1] smp: Brought up 1 node, 2 CPUs [ 0.018465][ T1] SMP: Total of 2 processors activated (100.00 BogoMIPS). [ 0.018473][ T1] CPU: All CPU(s) started in SVC mode. [ 0.018997][ T1] devtmpfs: initialized [ 0.025403][ T1] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6 [ 0.025789][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.025822][ T1] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.026157][ T1] prandom: seed boundary self test passed [ 0.028513][ T1] prandom: 100 self tests passed [ 0.028522][ T1] pinctrl core: initialized pinctrl subsystem [ 0.030119][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.030539][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.031702][ T1] audit: initializing netlink subsys (disabled) [ 0.031981][ T25] audit: type=2000 audit(0.030:1): state=initialized audit_enabled=0 res=1 [ 0.032657][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.032733][ T1] cpuidle: using governor ladder [ 0.032767][ T1] cpuidle: using governor menu [ 0.033063][ T17] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0 [ 0.033073][ T17] hw-breakpoint: CPU 0 failed to disable vector catch [ 0.033106][ T18] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 1 [ 0.036246][ T1] platform soc: Fixed dependency cycle(s) with /soc/internal-regs/interrupt-controller@20a00 [ 0.210111][ T1] raid6: int32x8 gen() 252 MB/s [ 0.380088][ T1] raid6: int32x4 gen() 272 MB/s [ 0.550067][ T1] raid6: int32x2 gen() 422 MB/s [ 0.720079][ T1] raid6: int32x1 gen() 401 MB/s [ 0.720087][ T1] raid6: using algorithm int32x2 gen() 422 MB/s [ 0.890077][ T1] raid6: .... xor() 247 MB/s, rmw enabled [ 0.890084][ T1] raid6: using intx1 recovery algorithm [ 0.891234][ T1] SCSI subsystem initialized [ 0.891707][ T1] usbcore: registered new interface driver usbfs [ 0.891756][ T1] usbcore: registered new interface driver hub [ 0.891804][ T1] usbcore: registered new device driver usb [ 0.892189][ T1] pps_core: LinuxPPS API ver. 1 registered [ 0.892196][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.892219][ T1] PTP clock support registered [ 0.894308][ T1] vgaarb: loaded [ 0.894931][ T1] clocksource: Switched to clocksource armada_370_xp_clocksource [ 0.895520][ T1] VFS: Disk quotas dquot_6.6.0 [ 0.895609][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.909374][ T1] NET: Registered PF_INET protocol family [ 0.909557][ T1] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.910905][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.911005][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.911028][ T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.911078][ T1] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.911135][ T1] TCP: Hash tables configured (established 4096 bind 4096) [ 0.911403][ T1] MPTCP token hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.911472][ T1] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.911496][ T1] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.911725][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.912417][ T1] RPC: Registered named UNIX socket transport module. [ 0.912426][ T1] RPC: Registered udp transport module. [ 0.912431][ T1] RPC: Registered tcp transport module. [ 0.912436][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.912452][ T1] PCI: CLS 0 bytes, default 64 [ 0.912751][ T11] Trying to unpack rootfs image as initramfs... [ 0.925042][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.926876][ T1] Initialise system trusted keyrings [ 0.926951][ T1] Key type blacklist registered [ 0.928549][ T1] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.928782][ T1] zbud: loaded [ 0.930827][ T1] NFS: Registering the id_resolver key type [ 0.930875][ T1] Key type id_resolver registered [ 0.930882][ T1] Key type id_legacy registered [ 0.930941][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.930958][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 0.995427][ T1] xor: measuring software checksum speed [ 1.004190][ T1] arm4regs : 1124 MB/sec [ 1.014520][ T1] 8regs : 959 MB/sec [ 1.022617][ T1] 32regs : 1221 MB/sec [ 1.022627][ T1] xor: using function: 32regs (1221 MB/sec) [ 1.022647][ T1] async_tx: api initialized (async) [ 1.022661][ T1] Key type asymmetric registered [ 1.022669][ T1] Asymmetric key parser 'x509' registered [ 1.023063][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 1.023219][ T1] io scheduler bfq registered [ 1.028310][ T1] armada-xp-pinctrl d0018000.pin-ctrl: registered pinctrl driver [ 1.030601][ T1] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 1.031318][ T1] debugfs: Directory 'd0018100.gpio' with parent 'regmap' already present! [ 1.032274][ T1] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 1.032895][ T1] debugfs: Directory 'd0018140.gpio' with parent 'regmap' already present! [ 1.034664][ T1] mvebu-pcie soc:pcie@82000000: host bridge /soc/pcie@82000000 ranges: [ 1.034736][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00d0040000..0x00d0041fff -> 0x0000040000 [ 1.034773][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00d0044000..0x00d0045fff -> 0x0000044000 [ 1.034810][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00d0048000..0x00d0049fff -> 0x0000048000 [ 1.034846][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00d004c000..0x00d004dfff -> 0x000004c000 [ 1.034881][ T1] mvebu-pcie soc:pcie@82000000: MEM 0x00d0080000..0x00d0081fff -> 0x0000080000 [ 1.034915][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 1.035020][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 1.035056][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 [ 1.035089][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000 [ 1.035123][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0300000000 [ 1.035156][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0300000000 [ 1.035188][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0400000000 [ 1.035221][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0400000000 [ 1.035253][ T1] mvebu-pcie soc:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0500000000 [ 1.035275][ T1] mvebu-pcie soc:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0500000000 [ 1.036197][ T1] mvebu-pcie soc:pcie@82000000: PCI host bridge to bus 0000:00 [ 1.036213][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.036228][ T1] pci_bus 0000:00: root bus resource [mem 0xd0040000-0xd0041fff] (bus address [0x00040000-0x00041fff]) [ 1.036240][ T1] pci_bus 0000:00: root bus resource [mem 0xd0044000-0xd0045fff] (bus address [0x00044000-0x00045fff]) [ 1.036252][ T1] pci_bus 0000:00: root bus resource [mem 0xd0048000-0xd0049fff] (bus address [0x00048000-0x00049fff]) [ 1.036263][ T1] pci_bus 0000:00: root bus resource [mem 0xd004c000-0xd004dfff] (bus address [0x0004c000-0x0004dfff]) [ 1.036275][ T1] pci_bus 0000:00: root bus resource [mem 0xd0080000-0xd0081fff] (bus address [0x00080000-0x00081fff]) [ 1.036285][ T1] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff] [ 1.036294][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 1.036403][ T1] pci 0000:00:01.0: [11ab:7823] type 01 class 0x060400 [ 1.037346][ T1] pci 0000:00:05.0: [11ab:7823] type 01 class 0x060400 [ 1.039072][ T1] PCI: bus0: Fast back to back transfers disabled [ 1.039096][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.039124][ T1] pci 0000:00:05.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.063267][ T1] pci 0000:01:00.0: [11ab:7042] type 00 class 0x010000 [ 1.063306][ T1] pci 0000:01:00.0: reg 0x10: [mem 0x40000000-0x400fffff 64bit] [ 1.063329][ T1] pci 0000:01:00.0: reg 0x18: [io 0xf1100000-0xf11000ff] [ 1.063499][ T1] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 8.000 Gb/s with 2.5 GT/s PCIe x4 link) [ 1.063894][ T1] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 1.063941][ T1] PCI: bus1: Fast back to back transfers disabled [ 1.063960][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.064321][ T1] pci 0000:02:00.0: [1033:0194] type 00 class 0x0c0330 [ 1.064356][ T1] pci 0000:02:00.0: reg 0x10: [mem 0x4a000000-0x4a001fff 64bit] [ 1.064523][ T1] pci 0000:02:00.0: PME# supported from D0 D3hot [ 1.105074][ T1] PCI: bus2: Fast back to back transfers disabled [ 1.105096][ T1] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 1.105157][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xf8000000-0xf80fffff] [ 1.105173][ T1] pci 0000:00:05.0: BAR 14: assigned [mem 0xf8100000-0xf81fffff] [ 1.105185][ T1] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff] [ 1.105201][ T1] pci 0000:01:00.0: BAR 0: assigned [mem 0xf8000000-0xf80fffff 64bit] [ 1.105224][ T1] pci 0000:01:00.0: BAR 2: assigned [io 0x10000-0x100ff] [ 1.105239][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.105249][ T1] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 1.105272][ T1] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xf80fffff] [ 1.105297][ T1] pci 0000:02:00.0: BAR 0: assigned [mem 0xf8100000-0xf8101fff 64bit] [ 1.105317][ T1] pci 0000:00:05.0: PCI bridge to [bus 02] [ 1.105329][ T1] pci 0000:00:05.0: bridge window [mem 0xf8100000-0xf81fffff] [ 1.105517][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 1.105662][ T1] pcieport 0000:00:05.0: enabling device (0140 -> 0142) [ 1.106516][ T1] mv_xor d0060900.xor: Marvell shared XOR driver [ 1.176180][ T1] mv_xor d0060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.180331][ T1] mv_xor d00f0900.xor: Marvell shared XOR driver [ 1.246230][ T1] mv_xor d00f0900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.372685][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.376468][ T1] printk: console [ttyS0] disabled [ 1.396836][ T1] d0012000.serial: ttyS0 at MMIO 0xd0012000 (irq = 37, base_baud = 15625000) is a 16550A [ 1.396909][ T1] printk: console [ttyS0] enabled [ 1.434145][ T11] Freeing initrd memory: 9908K [ 2.851585][ T1] sata_mv 0000:01:00.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx [ 2.863973][ T1] scsi host0: sata_mv [ 2.868811][ T1] scsi host1: sata_mv [ 2.873678][ T1] scsi host2: sata_mv [ 2.878435][ T1] scsi host3: sata_mv [ 2.882607][ T1] ata1: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8022000 irq 38 [ 2.891044][ T1] ata2: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8024000 irq 38 [ 2.899457][ T1] ata3: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8026000 irq 38 [ 2.907861][ T1] ata4: SATA max UDMA/133 mmio m1048576@0xf8000000 port 0xf8028000 irq 38 [ 2.917765][ T1] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xd3 [ 2.924851][ T1] nand: Samsung NAND 1GiB 3,3V 8-bit [ 2.930039][ T1] nand: 1024 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 2.938492][ T1] marvell-nfc d00d0000.nand-controller: No minimum ECC strength, using 1b/512B [ 2.947784][ T1] Bad block table found at page 524224, version 0x01 [ 2.955015][ T1] Bad block table found at page 524160, version 0x01 [ 2.961901][ T1] nand_read_bbt: bad block at 0x000003c60000 [ 2.967950][ T1] 6 fixed-partitions partitions found on MTD device pxa3xx_nand-0 [ 2.975662][ T1] Creating 6 MTD partitions on "pxa3xx_nand-0": [ 2.981822][ T1] 0x000000000000-0x0000000e0000 : "u-boot" [ 2.989367][ T1] 0x0000000e0000-0x000000100000 : "u-boot-env" [ 2.997040][ T1] 0x000000100000-0x000000120000 : "u-boot-env2" [ 3.004814][ T1] 0x000000120000-0x000000520000 : "zImage" [ 3.012136][ T1] 0x000000520000-0x000000920000 : "initrd" [ 3.019475][ T1] 0x000000e00000-0x000040000000 : "boot" [ 3.031335][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 3.039928][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 3.084470][ T1] mvneta d0070000.ethernet eth0: Using random mac address 92:93:b2:5f:19:ef [ 3.095799][ T1] mvneta d0074000.ethernet eth1: Using random mac address 96:b3:72:2f:22:1b [ 3.104819][ T1] usbcore: registered new interface driver smsc75xx [ 3.111797][ T1] orion-ehci d0050000.usb: EHCI Host Controller [ 3.117964][ T1] orion-ehci d0050000.usb: new USB bus registered, assigned bus number 1 [ 3.126417][ T1] orion-ehci d0050000.usb: irq 42, io mem 0xd0050000 [ 3.154981][ T1] orion-ehci d0050000.usb: USB 2.0 started, EHCI 1.00 [ 3.161916][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.04 [ 3.170938][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.178907][ T1] usb usb1: Product: EHCI Host Controller [ 3.184503][ T1] usb usb1: Manufacturer: Linux 6.4.11-mvebu-tld-1 ehci_hcd [ 3.191679][ T1] usb usb1: SerialNumber: d0050000.usb [ 3.197838][ T1] hub 1-0:1.0: USB hub found [ 3.202347][ T1] hub 1-0:1.0: 1 port detected [ 3.207766][ T1] orion-ehci d0051000.usb: EHCI Host Controller [ 3.213907][ T1] orion-ehci d0051000.usb: new USB bus registered, assigned bus number 2 [ 3.222340][ T1] orion-ehci d0051000.usb: irq 43, io mem 0xd0051000 [ 3.264951][ T1] orion-ehci d0051000.usb: USB 2.0 started, EHCI 1.00 [ 3.271849][ T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.04 [ 3.280875][ T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.288842][ T1] usb usb2: Product: EHCI Host Controller [ 3.294439][ T1] usb usb2: Manufacturer: Linux 6.4.11-mvebu-tld-1 ehci_hcd [ 3.301615][ T1] usb usb2: SerialNumber: d0051000.usb [ 3.307673][ T1] hub 2-0:1.0: USB hub found [ 3.312179][ T1] hub 2-0:1.0: 1 port detected [ 3.317899][ T1] usbcore: registered new interface driver usblp [ 3.324193][ T1] usbcore: registered new interface driver usb-storage [ 3.331395][ T1] mousedev: PS/2 mouse device common for all mice [ 3.339199][ T1] rtc-mv d0010300.rtc: registered as rtc0 [ 3.344817][ T1] rtc-mv d0010300.rtc: setting system clock to 2023-09-10T09:09:46 UTC (1694336986) [ 3.354582][ T1] i2c_dev: i2c /dev entries driver [ 3.359900][ T1] mv64xxx_i2c d0011000.i2c: can't get pinctrl, bus recovery not supported [ 3.369194][ T1] at24 0-0050: supply vcc not found, using dummy regulator [ 3.376904][ T1] at24 0-0050: 8192 byte 24c64 EEPROM, writable, 1 bytes/write [ 3.385675][ T1] rtc-pcf8563 0-0051: registered as rtc1 [ 3.415013][ T674] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 3.424575][ T674] ata1.00: ATA-7: WDC WD800JD-75MSA3, 10.01E04, max UDMA/133 [ 3.432029][ T674] ata1.00: 156250000 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 3.442253][ T674] ata1.00: configured for UDMA/133 [ 3.457880][ T11] scsi 0:0:0:0: Direct-Access ATA WDC WD800JD-75MS 1E04 PQ: 0 ANSI: 5 [ 3.468440][ T694] sd 0:0:0:0: [sda] 156250000 512-byte logical blocks: (80.0 GB/74.5 GiB) [ 3.477444][ T694] sd 0:0:0:0: [sda] Write Protect is off [ 3.483107][ T694] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 3.493061][ T694] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 3.494745][ T1] orion_wdt: Initial timeout 171 sec [ 3.505851][ T1] device-mapper: uevent: version 1.0.3 [ 3.511633][ T1] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com [ 3.521305][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 3.528648][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 3.536128][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 3.543544][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 3.550431][ T694] sda: sda1 sda2 sda3 < sda5 > [ 3.551779][ T1] debugfs: Directory 'cpu1' with parent 'opp' already present! [ 3.563696][ T694] sd 0:0:0:0: [sda] Attached SCSI disk [ 3.564443][ T1] sdhci: Secure Digital Host Controller Interface driver [ 3.575990][ T1] sdhci: Copyright(c) Pierre Ossman [ 3.581211][ T1] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.590255][ T1] marvell-cesa d0090000.crypto: CESA device successfully registered [ 3.598396][ T1] hid: raw HID events driver (C) Jiri Kosina [ 3.604574][ T1] usbcore: registered new interface driver usbhid [ 3.610915][ T112] usb 2-1: new full-speed USB device number 2 using orion-ehci [ 3.618377][ T1] usbhid: USB HID core driver [ 3.623631][ T1] NET: Registered PF_INET6 protocol family [ 3.631215][ T1] Segment Routing with IPv6 [ 3.635726][ T1] RPL Segment Routing with IPv6 [ 3.640541][ T1] In-situ OAM (IOAM) with IPv6 [ 3.645286][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.653490][ T1] NET: Registered PF_PACKET protocol family [ 3.660171][ T1] 8021q: 802.1Q VLAN Support v1.8 [ 3.665183][ T1] Key type dns_resolver registered [ 3.670389][ T1] ThumbEE CPU extension supported. [ 3.675415][ T1] Registering SWP/SWPB emulation handler [ 3.722925][ T1] registered taskstats version 1 [ 3.736018][ T1] Loading compiled-in X.509 certificates [ 3.742425][ T1] Key type .fscrypt registered [ 3.747720][ T1] Key type fscrypt-provisioning registered [ 3.753538][ T1] Key type big_key registered [ 3.781907][ T1] Key type encrypted registered [ 3.794574][ T1] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.803065][ T1] clk: Disabling unused clocks [ 3.852672][ T112] usb 2-1: New USB device found, idVendor=8086, idProduct=0808, bcdDevice= 1.00 [ 3.861650][ T112] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.869548][ T112] usb 2-1: Product: USB PnP Sound Device [ 3.875073][ T112] usb 2-1: Manufacturer: C-Media Electronics Inc. [ 3.886689][ T112] input: C-Media Electronics Inc. USB PnP Sound Device as /devices/platform/soc/soc:internal-regs/d0051000.usb/usb2/2-1/2-1:1.3/0003:8086:0808.0001/input/input1 [ 3.975659][ T679] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 3.975725][ T112] hid-generic 0003:8086:0808.0001: input,hidraw0: USB HID v1.00 Device [C-Media Electronics Inc. USB PnP Sound Device] on usb-d0051000.usb-1/input3 [ 3.985596][ T679] ata2.00: ATA-10: WDC WD5000AZLX-75K2TA0, 01.01A01, max UDMA/133 [ 4.006546][ T679] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 4.017213][ T679] ata2.00: configured for UDMA/133 [ 4.022895][ T41] scsi 1:0:0:0: Direct-Access ATA WDC WD5000AZLX-7 1A01 PQ: 0 ANSI: 5 [ 4.033982][ T893] sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 4.042260][ T893] sd 1:0:0:0: [sdb] 4096-byte physical blocks [ 4.048295][ T893] sd 1:0:0:0: [sdb] Write Protect is off [ 4.053920][ T893] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.063866][ T893] sd 1:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes [ 4.495124][ T893] sd 1:0:0:0: [sdb] Attached SCSI disk [ 4.535737][ T684] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.575781][ T684] ata3.00: ATA-8: WDC WD5000AAKS-00A7B0, 01.03B01, max UDMA/133 [ 4.583317][ T684] ata3.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 4.594139][ T684] ata3.00: configured for UDMA/133 [ 4.610223][ T432] scsi 2:0:0:0: Direct-Access ATA WDC WD5000AAKS-0 3B01 PQ: 0 ANSI: 5 [ 4.622059][ T41] sd 2:0:0:0: [sdc] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 4.630662][ T41] sd 2:0:0:0: [sdc] Write Protect is off [ 4.636556][ T41] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.646724][ T41] sd 2:0:0:0: [sdc] Preferred minimum I/O size 512 bytes [ 4.662887][ T41] sd 2:0:0:0: [sdc] Attached SCSI disk [ 4.959184][ T689] ata4: SATA link down (SStatus 0 SControl 300) [ 4.978339][ T1] Freeing unused kernel image (initmem) memory: 1024K [ 4.987279][ T1] Checked W+X mappings: passed, no W+X pages found [ 4.993744][ T1] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u4 [ 6.661422][ T1326] mtdblock: MTD device 'u-boot' is NAND, please consider using UBI block devices instead. [ 6.678383][ T1325] mtdblock: MTD device 'u-boot-env' is NAND, please consider using UBI block devices instead. [ 6.683404][ T1327] mtdblock: MTD device 'u-boot-env2' is NAND, please consider using UBI block devices instead. [ 6.704816][ T1329] mtdblock: MTD device 'zImage' is NAND, please consider using UBI block devices instead. [ 6.715261][ T1326] mtdblock: MTD device 'boot' is NAND, please consider using UBI block devices instead. [ 6.737264][ T1329] mtdblock: MTD device 'initrd' is NAND, please consider using UBI block devices instead. [ 6.822289][ T1334] xhci_hcd 0000:02:00.0: xHCI Host Controller [ 6.886885][ T1334] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 3 [ 6.897432][ T1334] xhci_hcd 0000:02:00.0: hcc params 0x014042cb hci version 0x96 quirks 0x0000000000000004 [ 6.910691][ T1334] xhci_hcd 0000:02:00.0: xHCI Host Controller [ 6.918967][ T1334] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 4 [ 6.929257][ T1334] xhci_hcd 0000:02:00.0: Host supports USB 3.0 SuperSpeed [ 6.941652][ T1334] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.04 [ 6.953013][ T1334] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.964235][ T1334] usb usb3: Product: xHCI Host Controller [ 6.971237][ T1334] usb usb3: Manufacturer: Linux 6.4.11-mvebu-tld-1 xhci-hcd [ 6.980472][ T1334] usb usb3: SerialNumber: 0000:02:00.0 [ 6.991479][ T1334] hub 3-0:1.0: USB hub found [ 6.998881][ T1334] hub 3-0:1.0: 2 ports detected [ 7.009749][ T1334] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 7.022805][ T1334] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.04 [ 7.034105][ T1334] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.052315][ T1334] usb usb4: Product: xHCI Host Controller [ 7.060167][ T1334] usb usb4: Manufacturer: Linux 6.4.11-mvebu-tld-1 xhci-hcd [ 7.072928][ T1334] usb usb4: SerialNumber: 0000:02:00.0 [ 7.088854][ T1334] hub 4-0:1.0: USB hub found [ 7.106894][ T1334] hub 4-0:1.0: 2 ports detected Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.36.1 [/sbin/fsck.ext4 (1) -- /dev/sda2] fsck.ext4 -a -C0 /dev/sda2 rootfs: clean, 41263/4825088 files, 867790/19283712 blocks done. [ 13.690590][ T1367] EXT4-fs (sda2): mounted filesystem 6e579b6a-87f3-482e-a34a-faad820bb1e5 r/w with ordered data mode. Quota mode: none. done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 16.557200][ T1] systemd[1]: systemd 247.3-7+deb11u4 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 16.582478][ T1] systemd[1]: Detected architecture arm. Welcome to [1mDebian GNU/Linux 11 (bullseye)[0m! [ 16.699111][ T1] systemd[1]: Set hostname to <lenovo>. [ 17.766166][ T37] platform gpio-leds: deferred probe pending [ 19.471848][ T1] systemd[1]: Queued start job for default target Graphical Interface. [ 20.165353][ C0] random: crng init done [ 20.210794][ T1] systemd[1]: Created slice system-getty.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-getty.slice[0m. [ 20.228640][ T1] systemd[1]: Created slice system-modprobe.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-modprobe.slice[0m. [ 20.268528][ T1] systemd[1]: Created slice system-serial\x2dgetty.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-serial\x2dgetty.slice[0m. [ 20.308550][ T1] systemd[1]: Created slice system-systemd\x2dfsck.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-systemd\x2dfsck.slice[0m. [ 20.348188][ T1] systemd[1]: Created slice User and Session Slice. [[0;32m OK [0m] Created slice [0;1;39mUser and Session Slice[0m. [ 20.386375][ T1] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [[0;32m OK [0m] Started [0;1;39mDispatch Password …ts to Console Directory Watch[0m. [ 20.426199][ T1] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [[0;32m OK [0m] Started [0;1;39mForward Password R…uests to Wall Directory Watch[0m. [ 20.467169][ T1] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [[0;32m OK [0m] Set up automount [0;1;39mArbitrary…s File System Automount Point[0m. [ 20.516070][ T1] systemd[1]: Reached target Local Encrypted Volumes. [[0;32m OK [0m] Reached target [0;1;39mLocal Encrypted Volumes[0m. [ 20.556041][ T1] systemd[1]: Reached target Paths. [[0;32m OK [0m] Reached target [0;1;39mPaths[0m. [ 20.595768][ T1] systemd[1]: Reached target Remote File Systems. [[0;32m OK [0m] Reached target [0;1;39mRemote File Systems[0m. [ 20.635730][ T1] systemd[1]: Reached target Slices. [[0;32m OK [0m] Reached target [0;1;39mSlices[0m. [ 20.699560][ T1] systemd[1]: Listening on Syslog Socket. [[0;32m OK [0m] Listening on [0;1;39mSyslog Socket[0m. [ 20.736777][ T1] systemd[1]: Listening on fsck to fsckd communication Socket. [[0;32m OK [0m] Listening on [0;1;39mfsck to fsckd communication Socket[0m. [ 20.754742][ T1] systemd[1]: Listening on initctl Compatibility Named Pipe. [[0;32m OK [0m] Listening on [0;1;39minitctl Compatibility Named Pipe[0m. [ 20.773589][ T1] systemd[1]: Listening on Journal Audit Socket. [[0;32m OK [0m] Listening on [0;1;39mJournal Audit Socket[0m. [ 20.816819][ T1] systemd[1]: Listening on Journal Socket (/dev/log). [[0;32m OK [0m] Listening on [0;1;39mJournal Socket (/dev/log)[0m. [ 20.857078][ T1] systemd[1]: Listening on Journal Socket. [[0;32m OK [0m] Listening on [0;1;39mJournal Socket[0m. [ 20.898271][ T1] systemd[1]: Listening on udev Control Socket. [[0;32m OK [0m] Listening on [0;1;39mudev Control Socket[0m. [ 20.913931][ T1] systemd[1]: Listening on udev Kernel Socket. [[0;32m OK [0m] Listening on [0;1;39mudev Kernel Socket[0m. [ 20.929824][ T1] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 20.996276][ T1] systemd[1]: Mounting POSIX Message Queue File System... Mounting [0;1;39mPOSIX Message Queue File System[0m... [ 21.021483][ T1] systemd[1]: Mounting Kernel Debug File System... Mounting [0;1;39mKernel Debug File System[0m... [ 21.056462][ T1] systemd[1]: Condition check resulted in Kernel Trace File System being skipped. [ 21.076086][ T1] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting [0;1;39mCreate list of st…odes for the current kernel[0m... [ 21.103997][ T1] systemd[1]: Starting Load Kernel Module configfs... Starting [0;1;39mLoad Kernel Module configfs[0m... [ 21.187034][ T1] systemd[1]: Starting Load Kernel Module drm... Starting [0;1;39mLoad Kernel Module drm[0m... [ 21.235914][ T1] systemd[1]: Starting Load Kernel Module fuse... Starting [0;1;39mLoad Kernel Module fuse[0m... [ 21.494205][ T1] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 21.504537][ T1] systemd[1]: Condition check resulted in File System Check on Root Device being skipped. [ 21.551133][ T1400] fuse: init (API version 7.38) [ 21.557558][ T1] systemd[1]: Starting Journal Service... Starting [0;1;39mJournal Service[0m... [ 21.669490][ T1] systemd[1]: Starting Load Kernel Modules... Starting [0;1;39mLoad Kernel Modules[0m... [ 21.766439][ T1] systemd[1]: Starting Remount Root and Kernel File Systems... Starting [0;1;39mRemount Root and Kernel File Systems[0m... [ 21.821065][ T1] systemd[1]: Starting Coldplug All udev Devices... Starting [0;1;39mColdplug All udev Devices[0m... [ 21.909593][ T1] systemd[1]: Mounted POSIX Message Queue File System. [[0;32m OK [0m] Mounted [0;1;39mPOSIX Message Queue File System[0m. [ 21.938446][ T1405] EXT4-fs (sda2): re-mounted 6e579b6a-87f3-482e-a34a-faad820bb1e5 r/w. Quota mode: none. [ 21.964670][ T1] systemd[1]: Mounted Kernel Debug File System. [[0;32m OK [0m] Mounted [0;1;39mKernel Debug File System[0m. [ 21.982028][ T1] systemd[1]: Finished Create list of static device nodes for the current kernel. [[0;32m OK [0m] Finished [0;1;39mCreate list of st… nodes for the current kernel[0m. [ 22.030914][ T1] systemd[1]: modprobe@configfs.service: Succeeded. [ 22.055757][ T1] systemd[1]: Finished Load Kernel Module configfs. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module configfs[0m. [ 22.099276][ T1] systemd[1]: modprobe@drm.service: Succeeded. [ 22.108932][ T1] systemd[1]: Finished Load Kernel Module drm. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module drm[0m. [ 22.149856][ T1] systemd[1]: modprobe@fuse.service: Succeeded. [ 22.160334][ T1] systemd[1]: Finished Load Kernel Module fuse. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module fuse[0m. [ 22.183719][ T1402] adt7475 0-002e: ADT7473 device, revision 0 [ 22.190242][ T1402] adt7475 0-002e: Optional features: fan4 pwm2 [ 22.201533][ T1] systemd[1]: Finished Remount Root and Kernel File Systems. [[0;32m OK [0m] Finished [0;1;39mRemount Root and Kernel File Systems[0m. [ 22.275929][ T1] systemd[1]: Mounting FUSE Control File System... Mounting [0;1;39mFUSE Control File System[0m... [ 22.313784][ T1] systemd[1]: Mounting Kernel Configuration File System... Mountin[ 22.371491][ T1402] hwmon hwmon2: temp1_input not attached to any thermal zone g [0;1;39mKernel Configuration File System[0m... [ 22.389038][ T1402] hwmon hwmon3: temp1_input not attached to any thermal zone [ 22.416674][ T1] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. [ 22.420761][ T1402] hwmon hwmon4: temp1_input not attached to any thermal zone [ 22.455825][ T1] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped. [ 22.542604][ T1402] Asymmetric key parser 'pkcs8' registered [ 22.566522][ T1] systemd[1]: Starting Load/Save Random Seed... Starting [0;1;39mLoad/Save Random Seed[0m... [ 22.625297][ T1] systemd[1]: Starting Create System Users... Starting [0;1;39mCreate System Users[0m... [ 22.715068][ T1] systemd[1]: Finished Load Kernel Modules. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Modules[0m. [ 22.798556][ T1] systemd[1]: Mounted FUSE Control File System. [[0;32m OK [0m] Mounted [0;1;39mFUSE Control File System[0m. [ 22.847054][ T1] systemd[1]: Mounted Kernel Configuration File System. [[0;32m OK [0m] Mounted [0;1;39mKernel Configuration File System[0m. [ 22.916998][ T1] systemd[1]: Starting Apply Kernel Variables... Starting [0;1;39mApply Kernel Variables[0m... [ 22.956794][ T1] systemd[1]: Started Journal Service. [[0;32m OK [0m] Started [0;1;39mJournal Service[0m. Starting [0;1;39mFlush Journal to Persistent Storage[0m... [[0;32m OK [0m] Finished [0;1;39mApply Kernel Variables[0m. [ 23.296817][ T1401] systemd-journald[1401]: Received client request to flush runtime journal. [[0;32m OK [0m] Finished [0;1;39mLoad/Save Random Seed[0m. [[0;32m OK [0m] Finished [0;1;39mCreate System Users[0m. Starting [0;1;39mCreate Static Device Nodes in /dev[0m... [[0;32m OK [0m] Finished [0;1;39mColdplug All udev Devices[0m. Starting [0;1;39mHelper to synchronize boot up for ifupdown[0m... [[0;32m OK [0m] Finished [0;1;39mCreate Static Device Nodes in /dev[0m. [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems (Pre)[0m. Starting [0;1;39mRule-based Manage…for Device Events and Files[0m... [[0;32m OK [0m] Finished [0;1;39mFlush Journal to Persistent Storage[0m. [[0;32m OK [0m] Started [0;1;39mRule-based Manager for Device Events and Files[0m. [[0;32m OK [0m] Found device [0;1;39m/dev/ttyS0[0m. [ 26.450445][ T1420] mtdblock: MTD device 'u-boot' is NAND, please consider using UBI block devices instead. [ 26.491124][ T1424] mtdblock: MTD device 'u-boot-env' is NAND, please consider using UBI block devices instead. [ 26.594337][ T1427] mtdblock: MTD device 'zImage' is NAND, please consider using UBI block devices instead. [ 26.605500][ T1429] mtdblock: MTD device 'u-boot-env2' is NAND, please consider using UBI block devices instead. [ 26.663885][ T1426] mtdblock: MTD device 'initrd' is NAND, please consider using UBI block devices instead. [ 26.731962][ T1429] mtdblock: MTD device 'boot' is NAND, please consider using UBI block devices instead. [ 26.786404][ T1425] mc: Linux media interface: v0.10 [ 27.133634][ T1421] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 27.165233][ T1421] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 27.189418][ T1421] sd 2:0:0:0: Attached scsi generic sg2 type 0 [ 27.492910][ T1425] usbcore: registered new interface driver snd-usb-audio [ 27.755108][ T1456] Btrfs loaded, zoned=no, fsverity=no [ 27.766872][ T1421] BTRFS: device fsid bd9b4047-5599-4f64-b90d-119b70bcf29d devid 1 transid 399 /dev/sdb scanned by systemd-udevd (1421) [ 27.901144][ T1424] BTRFS: device fsid bd9b4047-5599-4f64-b90d-119b70bcf29d devid 2 transid 399 /dev/sdc scanned by systemd-udevd (1424) [[0;32m OK [0m] Found device [0;1;39mWDC_WD800JD-75MSA3 5[0m. Activating swap [0;1;39m/dev/disk/…1cde-44c3-89a7-2733df823c76[0m... [ 28.492444][ T1460] Adding 488444k swap on /dev/sda5. Priority:-2 extents:1 across:488444k FS [[0;32m OK [0m] Found device [0;1;39mWDC_WD800JD-75MSA3 1[0m. [[0;32m OK [0m] Activated swap [0;1;39m/dev/disk/b…5-1cde-44c3-89a7-2733df823c76[0m. [[0;32m OK [0m] Reached target [0;1;39mSwap[0m. Starting [0;1;39mFile System Check…7b5c-4e53-a7dd-21d251b98b49[0m... [[0;32m OK [0m] Started [0;1;39mFile System Check Daemon to report status[0m. [[0;32m OK [0m] Finished [0;1;39mFile System Check…f-7b5c-4e53-a7dd-21d251b98b49[0m. [[0;32m OK [0m] Finished [0;1;39mHelper to synchronize boot up for ifupdown[0m. Mounting [0;1;39m/boot[0m... [ 31.226011][ T1468] ext2 filesystem being mounted at /boot supports timestamps until 2038-01-19 (0x7fffffff) [[0;32m OK [0m] Mounted [0;1;39m/boot[0m. [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems[0m. Starting [0;1;39mRaise network interfaces[0m... Starting [0;1;39mCreate Volatile Files and Directories[0m... [[0;32m OK [0m] Finished [0;1;39mCreate Volatile Files and Directories[0m. [ 32.192951][ T1487] mvneta d0070000.ethernet eth0: PHY [d0072004.mdio-mii:00] driver [Marvell 88E1318S] (irq=POLL) [ 32.204106][ T1487] mvneta d0070000.ethernet eth0: configuring for phy/rgmii-id link mode Starting [0;1;39mNetwork Time Synchronization[0m... Starting [0;1;39mUpdate UTMP about System Boot/Shutdown[0m... [ 32.360001][ T1500] mvneta d0074000.ethernet eth1: PHY [d0072004.mdio-mii:01] driver [Marvell 88E1318S] (irq=POLL) [ 32.395624][ T1500] mvneta d0074000.ethernet eth1: configuring for phy/rgmii-id link mode [[0;1;31mFAILED[0m] Failed to start [0;1;39mRaise network interfaces[0m. See 'systemctl status networking.service' for details. [[0;32m OK [0m] Finished [0;1;39mUpdate UTMP about System Boot/Shutdown[0m. [[0;32m OK [0m] Reached target [0;1;39mNetwork[0m. [[0;32m OK [0m] Reached target [0;1;39mNetwork is Online[0m. [[0;32m OK [0m] Started [0;1;39mNetwork Time Synchronization[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Initialization[0m. [[0;32m OK [0m] Started [0;1;39mDaily Cleanup of Temporary Directories[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Time Set[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Time Synchronized[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt download activities[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt upgrade and clean activities[0m. [[0;32m OK [0m] Started [0;1;39mPeriodic ext4 Onli…ata Check for All Filesystems[0m. [[0;32m OK [0m] Started [0;1;39mDiscard unused blocks once a week[0m. [[0;32m OK [0m] Started [0;1;39mDaily rotation of log files[0m. [[0;32m OK [0m] Started [0;1;39mDaily man-db regeneration[0m. [[0;32m OK [0m] Reached target [0;1;39mTimers[0m. [[0;32m OK [0m] Listening on [0;1;39mAvahi mDNS/DNS-SD Stack Activation Socket[0m. [[0;32m OK [0m] Listening on [0;1;39mD-Bus System Message Bus Socket[0m. [[0;32m OK [0m] Reached target [0;1;39mSockets[0m. [[0;32m OK [0m] Reached target [0;1;39mBasic System[0m. Starting [0;1;39mSave/Restore Sound Card State[0m... Starting [0;1;39mAvahi mDNS/DNS-SD Stack[0m... [[0;32m OK [0m] Started [0;1;39mRegular background program processing daemon[0m. [[0;32m OK [0m] Started [0;1;39mD-Bus System Message Bus[0m. Starting [0;1;39mRemove Stale Onli…t4 Metadata Check Snapshots[0m... Starting [0;1;39mInitialize hardware monitoring sensors[0m... Starting [0;1;39mSystem Logging Service[0m... Starting [0;1;39mSelf Monitoring a…g Technology (SMART) Daemon[0m... Starting [0;1;39mOpenBSD Secure Shell server[0m... Starting [0;1;39mUser Login Management[0m... Starting [0;1;39mPermit User Sessions[0m... [[0;32m OK [0m] Finished [0;1;39mSave/Restore Sound Card State[0m. [[0;32m OK [0m] Reached target [0;1;39mSound Card[0m. Starting [0;1;39mRotate log files[0m... Starting [0;1;39mDaily man-db regeneration[0m... [[0;32m OK [0m] Finished [0;1;39mPermit User Sessions[0m. [[0;32m OK [0m] Started [0;1;39mGetty on tty1[0m. [[0;32m OK [0m] Started [0;1;39mSerial Getty on ttyS0[0m. [[0;32m OK [0m] Reached target [0;1;39mLogin Prompts[0m. [[0;32m OK [0m] Finished [0;1;39mInitialize hardware monitoring sensors[0m. Starting [0;1;39mfan speed regulator[0m... [[0;32m OK [0m] Finished [0;1;39mRemove Stale Onli…ext4 Metadata Check Snapshots[0m. [[0;32m OK [0m] Started [0;1;39mSystem Logging Service[0m. [[0;32m OK [0m] Finished [0;1;39mRotate log files[0m. [[0;32m OK [0m] Started [0;1;39mfan speed regulator[0m. [[0;32m OK [0m] Started [0;1;39mUser Login Management[0m. [[0;32m OK [0m] Started [0;1;39mAvahi mDNS/DNS-SD Stack[0m. [[0;32m OK [0m] Started [0;1;39mShairport Sync - AirPlay Audio Receiver[0m. [[0;32m OK [0m] Started [0;1;39mOpenBSD Secure Shell server[0m. [[0;32m OK [0m] Started [0;1;39mSelf Monitoring an…ing Technology (SMART) Daemon[0m. [[0;32m OK [0m] Reached target [0;1;39mMulti-User System[0m. [[0;32m OK [0m] Reached target [0;1;39mGraphical Interface[0m. [[0;32m OK [0m] Started [0;1;39mManage keyboard display[0m. [[0;32m OK [0m] Started [0;1;39mManage LCD display[0m. Starting [0;1;39mUpdate UTMP about System Runlevel Changes[0m... [ 40.076729][ T1520] fbcon: Taking over console Debian GNU/Linux 11 lenovo ttyS0 lenovo login:
Re: Mainline Debian on Iomega ix4-300d September 10, 2023 02:18PM |
Admin Registered: 13 years ago Posts: 18,821 |
[ 16.557200][ T1] systemd[1]: systemd 247.3-7+deb11u4 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 16.582478][ T1] systemd[1]: Detected architecture arm. Welcome to [1mDebian GNU/Linux 11 (bullseye)[0m! [ 16.699111][ T1] systemd[1]: Set hostname to <lenovo>. [ 17.766166][ T37] platform gpio-leds: deferred probe pending [ 19.471848][ T1] systemd[1]: Queued start job for default target Graphical Interface. [ 20.165353][ C0] random: crng init done
alf45tar
Re: Mainline Debian on Iomega ix4-300d September 14, 2023 03:13PM |
platform gpio-leds: deferred probe pending
Re: Mainline Debian on Iomega ix4-300d September 14, 2023 04:30PM |
Admin Registered: 13 years ago Posts: 18,821 |
alf45tar
Re: Mainline Debian on Iomega ix4-300d September 16, 2023 10:33AM |
Re: Mainline Debian on Iomega ix4-300d September 16, 2023 02:17PM |
Admin Registered: 13 years ago Posts: 18,821 |
> CONFIG_GPIO_74X164=m >>
> ix4-300d:hdd:blue ix4-300d:hddfail:red > ix4-300d:power:white ix4-300d:sys:blue > ix4-300d:sysfail:red >>
Re: Mainline Debian on Iomega ix4-300d September 16, 2023 03:34PM |
Admin Registered: 13 years ago Posts: 18,821 |
ls -l /sys/class/leds/
cat /sys/class/leds/ix4-300d:hdd:blue/trigger cat /sys/class/leds/ix4-300d:hddfail:red/trigger
echo none > /sys/class/leds/ix4-300d:hdd:blue/trigger echo none > /sys/class/leds/ix4-300d:hddfail:red/trigger
echo default-on > /sys/class/leds/ix4-300d:hdd:blue/trigger
alf45tar
Re: Mainline Debian on Iomega ix4-300d September 16, 2023 04:19PM |
Re: Mainline Debian on Iomega ix4-300d November 12, 2023 07:09AM |
Registered: 9 months ago Posts: 3 |
Re: Mainline Debian on Iomega ix4-300d November 13, 2023 03:50AM |
Registered: 9 months ago Posts: 3 |
Re: Mainline Debian on Iomega ix4-300d November 13, 2023 04:51PM |
Registered: 10 years ago Posts: 226 |
Re: Mainline Debian on Iomega ix4-300d November 14, 2023 04:21PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Mainline Debian on Iomega ix4-300d November 15, 2023 04:22PM |
Registered: 9 months ago Posts: 3 |
# lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINTS sda 8:0 0 3.6T 0 disk |-sda1 8:1 0 20G 0 part | `-md0 9:0 0 20G 0 raid1 | |-md0_vg-BFDlv 253:0 0 4G 0 lvm | `-md0_vg-vol1 253:1 0 16G 0 lvm `-sda2 8:2 0 3.6T 0 part `-md1 9:1 0 10.9T 0 raid5 |-md1p1 259:0 0 487.5M 0 part /boot |-md1p2 259:1 0 10.9T 0 part / `-md1p3 259:2 0 475.5M 0 part [SWAP] sdb 8:16 1 495.5M 0 disk `-sdb1 8:17 1 494M 0 part sdc 8:32 0 3.6T 0 disk |-sdc1 8:33 0 20G 0 part | `-md0 9:0 0 20G 0 raid1 | |-md0_vg-BFDlv 253:0 0 4G 0 lvm | `-md0_vg-vol1 253:1 0 16G 0 lvm `-sdc2 8:34 0 3.6T 0 part `-md1 9:1 0 10.9T 0 raid5 |-md1p1 259:0 0 487.5M 0 part /boot |-md1p2 259:1 0 10.9T 0 part / `-md1p3 259:2 0 475.5M 0 part [SWAP] sdd 8:48 0 3.6T 0 disk |-sdd1 8:49 0 20G 0 part | `-md0 9:0 0 20G 0 raid1 | |-md0_vg-BFDlv 253:0 0 4G 0 lvm | `-md0_vg-vol1 253:1 0 16G 0 lvm `-sdd2 8:50 0 3.6T 0 part `-md1 9:1 0 10.9T 0 raid5 |-md1p1 259:0 0 487.5M 0 part /boot |-md1p2 259:1 0 10.9T 0 part / `-md1p3 259:2 0 475.5M 0 part [SWAP] sde 8:64 0 3.6T 0 disk |-sde1 8:65 0 20G 0 part | `-md0 9:0 0 20G 0 raid1 | |-md0_vg-BFDlv 253:0 0 4G 0 lvm | `-md0_vg-vol1 253:1 0 16G 0 lvm `-sde2 8:66 0 3.6T 0 part `-md1 9:1 0 10.9T 0 raid5 |-md1p1 259:0 0 487.5M 0 part /boot |-md1p2 259:1 0 10.9T 0 part / `-md1p3 259:2 0 475.5M 0 part [SWAP]
Re: Mainline Debian on Iomega ix4-300d November 15, 2023 07:58PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Mainline Debian on Iomega ix4-300d November 24, 2023 02:46PM |
Registered: 3 years ago Posts: 4 |
Re: Debian bookworm on Iomega ix4-300d March 04, 2024 09:09PM |
Registered: 3 years ago Posts: 4 |
setenv part1 'nand read 0x40000 $kernel_start $kernel_size;nand read 0x2000000 $initrd_start $initrd_size;' setenv part2 'setenv bootargs $console $mtdparts $bootargs_root mem=512M ramdisk_size=$ramdisk_size ramdisk_blocksize=1024 ip=$bootargs_end $mvNetConfig;' setenv part3 'bootm 0x40000 0x2000000;' setenv boot_nand $part$part2$part3;setenv part1;setenv part2;setenv part3 setenv bootcmd $boot_nand saveenv
setenv mtdparts $mtdparts_old setenv mtdparts_new mtdparts=pxa3xx_nand-0:0xe0000@0x0(uboot),0x20000@0xe0000(env),0x20000@0x100000(env2),0x400000@0x120000(zImage),0x400000@0x520000(initrd),0x3F200000@0xE00000(boot),0x40000000@0x0(flash) setenv boot_nand $bootcmd setenv hd_dev ide 2:1 setenv hd_root /dev/sda2 setenv hd_delay 10 setenv boot_hd 'ide reset;ext2load $hd_dev 40000 uImage;ext2load $hd_dev 2000000 uInitrd;setenv bootargs $console $mtdparts root=$hd_root rw rootdelay=$hd_delay;bootm 0x40000 0x2000000' setenv deb_install_net 'tftpboot uImage_di_ix4_300d_bookworm;bootm 0x2000000' setenv deb_install_usb 'ext2load usb 0:1 0x0040000 uImage_ix4_300d_bookworm; ext2load usb 0:1 0x2000000 uInitrd_ix4_300d_bookworm;setenv bootargs $console $mtdparts root=/dev/sda2 rw rootdelay=10;bootm 0x40000 0x2000000'I could now easily install via tfpt or USB from u-boot eg: 'run deb_install_net'.
setenv mtdparts $mtdparts_new setenv hd_root LABEL=rootfs setenv hd_delay 5 setenv bootcmd $boot_hdI was entering the saveenv command twice at each stage to ensure both copies were identicle.
[ 19.388903] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xd3 [ 19.395338] nand: Samsung NAND 1GiB 3,3V 8-bit [ 19.399823] nand: 1024 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 19.407535] marvell-nfc d00d0000.nand-controller: No minimum ECC strength, using 1b/512B [ 19.410024] at24 0-0050: 8192 byte 24c64 EEPROM, writable, 1 bytes/write [ 19.549743] Bad block table found at page 524224, version 0x01 [ 19.594060] Bad block table found at page 524160, version 0x01 [ 19.610770] nand_read_bbt: bad block at 0x0000111a0000 [ 19.615999] nand_read_bbt: bad block at 0x00001a6a0000 [ 19.616010] nand_read_bbt: bad block at 0x00001bc80000 [ 19.616026] nand_read_bbt: bad block at 0x00002f4a0000 [ 19.616040] nand_read_bbt: bad block at 0x00003ec60000 [ 19.664737] 6 fixed-partitions partitions found on MTD device pxa3xx_nand-0 [ 19.671776] Creating 6 MTD partitions on "pxa3xx_nand-0": [ 19.677273] 0x000000000000-0x0000000e0000 : "u-boot" [ 19.705285] 0x0000000e0000-0x000000100000 : "u-boot-env" [ 19.711783] 0x000000100000-0x000000120000 : "u-boot-env2" [ 19.718528] 0x000000120000-0x000000520000 : "zImage" [ 19.727087] 0x000000520000-0x000000920000 : "initrd" [ 19.733413] 0x000000e00000-0x000040000000 : "boot" [ 19.994103] marvell-cesa d0090000.crypto: CESA device successfully registeredWith the system fully booted, I can do 'fw_printenv' but 'fw_setenv' does not work even after trying 'flash_unlock /dev/mtd1' and 'flash_unlock /dev/mtd2'. It might be because of old uboot or broken setenv command. I intend to use the box to build new versions later when I get time.
mount --bind /dev /target/dev mount -t proc none /target/proc mount -t sysfs none /target/sys chroot /target /bin/shNow it is time to ensure root password is set and add a normal user by entering:
passwd useradd -m username passwd usernameNow I create a setup script with what needs to be done to get started.
nano /root/setup_server.sh #!/bin/bash apt update apt install -y flash-kernel cat <<EOF>>/etc/flash-kernel/db Machine: Lenovo Iomega ix4-300d Kernel-Flavors: armmp armmp-lpae DTB-Id: armada-xp-lenovo-ix4-300d.dtb DTB-Append: yes U-Boot-Kernel-Address: 0x00008000 U-Boot-Initrd-Address: 0x0 Boot-Kernel-Path: /boot/uImage Boot-Initrd-Path: /boot/uInitrd Boot-DTB-Path: /boot/dtb Required-Packages: u-boot-tools Bootloader-Sets-Incorrect-Root: no EOF update-initramfs -u if [ "$(df -Th /dev/sda2 | tail -n -1 | awk '{print $2}')" = "ext4" ]; then e2label /dev/sda2 rootfs; fi cat <<EOF>/etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd1 0x00000 0x20000 0x20000 /dev/mtd2 0x00000 0x20000 0x20000 EOF cd /bin; rm sh; ln -s bash sh echo "PermitRootLogin yes" >> /etc/ssh/sshd_config mkdir -p /home/root; cp -r $HOME/.* /home/root/; export HOME=/home/root; cd $HOME sed -i 's#:/root:#:/home/root:#' /etc/passwd echo -e "alias ls='ls --color=auto'\neval $(dircolors -b)\nexport TERM=xterm-256color EDITOR=nano" >>.bashrc echo "PS1='${debian_chroot:+($debian_chroot)}\[\033[01;32m\]\u@\h\[\033[00m\]:\[\033[01;34m\]\w\[\033[00m\]\$ '" >>.bashrc apt install -y sudo net-tools xterm avahi-daemon smartmontools lm-sensors fancontrol echo -e "i2c_mv64xxx\nadt7475\ndrivetemp" >>/etc/modules cat <<EOF>/etc/fancontrol # Configuration file generated by pwmconfig, changes will be lost INTERVAL=10 DEVPATH=hwmon1=devices/platform/soc/soc:internal-regs/d0011000.i2c/i2c-0/0-002e hwmon3=devices/platform/soc/soc:pcie@82000000/pci0000:00/0000:00:01.0/0000:01:00.0/ata2/host1/target1:0:0/1:0:0:0 DEVNAME=hwmon1=adt7473 hwmon3=drivetemp FCTEMPS= hwmon1/pwm1=hwmon3/temp1_input FCFANS= hwmon1/pwm1=hwmon1/fan1_input MINTEMP= hwmon1/pwm1=20 MAXTEMP= hwmon1/pwm1=60 MINSTART= hwmon1/pwm1=150 MINSTOP= hwmon1/pwm1=0 EOF systemctl restart fancontrol.service systemctl restart fancontrol.service echo 7 > /sys/class/i2c-adapter/i2c-0/0-002e/hwmon/hwmon1/pwm1_auto_channels_temp echo 2 > /sys/class/i2c-adapter/i2c-0/0-002e/hwmon/hwmon1/pwm1_enable apt install -y python3-periphery python3-pil python3-psutil mkdir -p /opt/ix4-300d wget -P /opt/ix4-300d https://raw.githubusercontent.com/alf45tar/ix4-300d/main/lcd.py cat <<EOF>/etc/systemd/system/lcd.service [Unit] Description=Manage LCD display After=default.target [Service] ExecStart=python3 /opt/ix4-300d/lcd.py [Install] WantedBy=default.target EOF systemctl daemon-reload systemctl enable lcd.service systemctl start lcd.service apt install -y evtest mkdir /opt/ix4-300d wget -P /opt/ix4-300d https://raw.githubusercontent.com/alf45tar/ix4-300d/main/kbdactions.sh chmod 755 /opt/ix4-300d/kbdactions.sh cat <<EOF> /opt/ix4-300d/kbdactions.sh #!/bin/bash device='/dev/input/event0' event_select_press='*code 314 (BTN_SELECT), value 1*' event_select_release='*code 314 (BTN_SELECT), value 0*' event_scroll_down_press='*code 178 (KEY_SCROLLDOWN), value 1*' event_scroll_down_release='*code 178 (KEY_SCROLLDOWN), value 0*' event_power='*code 116 (KEY_POWER), value 1*' event_restart='*code 408 (KEY_RESTART), value 1*' evtest "$device" | while read line; do case $line in ($event_select_press) systemctl is-active --quiet webmin.service && systemctl stop webmin.service || systemctl restart webmin.service ;; ($event_select_release) echo "SELECT release" ;; ($event_scroll_down_press) systemctl restart lcd.service ;; ($event_scroll_down_release) echo "SCROLl DOWN release" ;; ($event_power) echo "POWER" ;; ($event_restart) echo "RESTART" ;; esac done EOF cat <<EOF> /etc/systemd/system/kbdactions.service [Unit] Description=Manage keyboard display After=default.target [Service] ExecStart=/opt/ix4-300d/kbdactions.sh [Install] WantedBy=default.target EOF systemctl daemon-reload systemctl enable kbdactions.service systemctl start kbdactions.service wget https://raw.githubusercontent.com/alf45tar/ix4-300d/main/linux-image-6.1.0-12-armmp-lpae_6.1.52-2_armhf.deb dpkg -i linux-image-6.1.0-12-armmp-lpae_6.1.52-2_armhf.deb apt install -y gpiod cat <<EOF>/etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). source /etc/network/interfaces.d/* # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp auto eth1 iface eth1 inet static address 169.254.1.1 netmask 255.255.0.0 gateway 169.254.1.254 EOFHave fun and keep fighting the fight!
Re: Debian bookworm on Iomega ix4-300d March 04, 2024 10:31PM |
Admin Registered: 13 years ago Posts: 18,821 |
dmesg
Re: Mainline Debian on Iomega ix4-300d March 06, 2024 06:45AM |
Registered: 3 years ago Posts: 4 |
[ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=pxa3xx_nand-0:0x20000@0xe0000(env),0x20000@0x100000(env2),0x400000@0x120000(zImage),0x400000@0x520000(initrd),0x3F200000@0xE00000(boot),0x40000000@0x0(flash) root=LABEL=rootfs rw rootdelay=5 [ 0.000000] Unknown kernel command line parameters "mtdparts=pxa3xx_nand-0:0x20000@0xe0000(env),0x20000@0x100000(env2),0x400000@0x120000(zImage),0x400000@0x520000(initrd),0x3F200000@0xE00000(boot),0x40000000@0x0(flash)", will be passed to user space.
nano /opt/ix4-300d/fixmac.sh #!/bin/bash ip link set dev eth0 down ip link set dev eth0 address $(fw_printenv | grep ^ethaddr | cut -d'=' -f2) ip link set dev eth0 up ip link set dev eth1 down ip link set dev eth1 address $(fw_printenv | grep ^eth1addr | cut -d'=' -f2) ip link set dev eth1 up systemctl restart networking.serviceThen create service to run at boot.
nano /etc/systemd/system/fixmac.service [Unit] Description=Fix eth0 and eth1 Mac addresses [Service] Type=simple ExecStart=/opt/ix4-300d/fixmac.sh [Install] WantedBy=default.targetGet service running.
systemctl daemon-reload systemctl enable fixmac.service systemctl start fixmac.serviceI am currently investigating nothing in /sys/class/leds. I suspect the dtb file. The one I got from the walkthough site was not the same as 6.7.1. Converting both to dts and running a diff gave me:
diff armada-xp-lenovo-ix4-300d.dts armada-xp-lenovo-ix4-300d.dts2 302a303 > interrupts = <0x5d 0x26>; 892,893c893,894 < gpio-sck = <0x1e 0x19 0x01>; < gpio-mosi = <0x1d 0x0f 0x01>; --- > sck-gpios = <0x1e 0x19 0x01>; > mosi-gpios = <0x1d 0x0f 0x01>;I will have to keep digging.
Re: Mainline Debian on Iomega ix4-300d March 06, 2024 01:27PM |
Admin Registered: 13 years ago Posts: 18,821 |
Quote
https://forum.doozan.com/read.php?2,32146
Note 6. Persistent MAC address (Optional)