Pogo V4 - USB3 ports dead in Debian March 23, 2022 05:20AM |
Registered: 12 years ago Posts: 33 |
root@debian:~# lspci -v 00:01.0 PCI bridge: Marvell Technology Group Ltd. 88F6281 [Kirkwood] ARM SoC (rev 03) (prog-if 00 [Normal decode]) Device tree node: /sys/firmware/devicetree/base/mbus@f1000000/pcie@82000000/pcie@1,0 Flags: fast devsel Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: [disabled] Memory behind bridge: e0000000-ebffffff [size=192M] Prefetchable memory behind bridge: 00000000-000fffff [size=1M] Capabilities: [40] Express Root Port (Slot-), MSI 00 01:00.0 Memory controller: Marvell Technology Group Ltd. 88F6281 [Kirkwood] ARM SoC (rev 03) Subsystem: Marvell Technology Group Ltd. 88F6281 [Kirkwood] ARM SoC Flags: fast devsel Memory at e8000000 (32-bit, non-prefetchable) [size=1M] Memory at e0000000 (32-bit, non-prefetchable) [size=128M] Capabilities: [40] Power Management version 3 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [60] Express Root Port (Slot-), MSI 00 Capabilities: [100] Advanced Error Reporting root@debian:~# fw_printenv arcNumber=2097 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-pogoplug_v4.dtb ethact=egiga0 ethaddr=00:25:31:04:28:15 if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 machid=0x831 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15
Re: Pogo V4 - USB3 ports dead in Debian March 23, 2022 02:43PM |
Admin Registered: 13 years ago Posts: 18,613 |
dmesgPlug in the USB 3.0 drive, and
dmesg | tail -20And post the log here.
Re: Pogo V4 - USB3 ports dead in Debian March 23, 2022 03:50PM |
Registered: 12 years ago Posts: 33 |
root@debian:~# dmesg | tail -20 [ 19.467988] netpoll: netconsole: interface 'eth0' [ 19.473378] netpoll: netconsole: remote port 6666 [ 19.478802] netpoll: netconsole: remote IPv4 address 10.11.10.15 [ 19.485490] netpoll: netconsole: remote ethernet address ff:ff:ff:ff:ff:ff [ 19.493064] netpoll: netconsole: device eth0 not up yet, forcing it [ 24.086033] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 24.096671] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 24.113028] printk: console [netcon0] enabled [ 24.118454] netconsole: network logging started [ 34.580646] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none. [ 38.874486] orion_wdt: Initial timeout 25 sec [ 39.626473] marvell-cesa f1030000.crypto: CESA device successfully registered [ 41.078956] EXT4-fs (mmcblk0p1): re-mounted. Opts: errors=remount-ro. Quota mode: none. [ 43.624050] Adding 524284k swap on /swapfile. Priority:-2 extents:2 across:532476k SSFS [ 44.350619] random: dd: uninitialized urandom read (512 bytes read) [ 48.467449] random: dbus-daemon: uninitialized urandom read (12 bytes read) [ 48.510905] random: dbus-daemon: uninitialized urandom read (12 bytes read) [ 48.657880] random: avahi-daemon: uninitialized urandom read (4 bytes read) [ 51.686258] random: crng init done [ 51.690412] random: 1 urandom warning(s) missed due to ratelimiting
Re: Pogo V4 - USB3 ports dead in Debian March 23, 2022 04:25PM |
Admin Registered: 13 years ago Posts: 18,613 |
Re: Pogo V4 - USB3 ports dead in Debian March 23, 2022 04:36PM |
Registered: 12 years ago Posts: 33 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:34:01 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: MVEBU_MMC: 0 In: serial Out: serial Err: serial Net: egiga0 U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:34:01 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: MVEBU_MMC: 0 In: serial Out: serial Err: serial Net: egiga0 No link on egiga0 ping failed; host 10.11.10.15 is not alive Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Reset IDE: ide_preinit failed MMC rescan: current device # 0 initialized OK ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... ** Bad device usb 0 ** no IDE devices available Partition Map for MMC device 0 -- Partition Type: EFI Part Start LBA End LBA Name Attributes Type GUID Partition GUID 1 0x00000800 0x008007ff "" attrs: 0x0000000000000000 type: 0fc63daf-8483-4772-8e79-3d69d8477de4 type: linux guid: 85485f32-8814-0f41-931c-8fcf1a078701 loading envs from mmc 0 ... ** File not found /boot/uEnv.txt ** running scan_disk ... Scan device usb device usb 0:1 ** Bad device usb 0 ** device usb 1:1 ** Bad device usb 1 ** device usb 2:1 ** Bad device usb 2 ** device usb 3:1 ** Bad device usb 3 ** Scan device ide Reset IDE: ide_preinit failed device ide 0:1 ** Bad device ide 0 ** device ide 1:1 ** Bad device ide 1 ** device ide 2:1 ** Bad device ide 2 ** device ide 3:1 ** Bad device ide 3 ** Scan device mmc MMC rescan: current device # 0 initialized OK device mmc 0:1 1 bytes read in 12 ms (0 Bytes/s) Found bootable drive on mmc 0 loading uImage ... 5669000 bytes read in 160 ms (33.8 MiB/s) loading uInitrd ... 10173846 bytes read in 274 ms (35.4 MiB/s) loading DTB /boot/dts/kirkwood-pogoplug_v4.dtb ... 9970 bytes read in 30 ms (324.2 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-5.16.5-kirkwood-tld-1 Created: 2022-03-15 20:47:36 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5668936 Bytes = 5.4 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-5.16.5-kirkwood-tld-1 Created: 2022-03-15 20:47:45 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 10173782 Bytes = 9.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 07155000, end 07b08d56 ... OK Loading Device Tree to 0714f000, end 071546f1 ... OK Using machid 0xf78 from environment Starting kernel ... [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.16.5-kirkwood-tld-1 (root@tldDebianVM) (arm-linux-gnueabi-gcc (Ubuntu 9.3.0-17ubuntu1~20.04) 9.3.0, GNU ld (GNU Binutils for Ubuntu) 2.34) #1.0 PREEMPT Sat Feb 5 20:02:03 PST 2022 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Pogoplug v4 [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 32512 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) [ 0.000000][ T0] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 99544K/131072K available (11264K kernel code, 1610K rwdata, 4968K rodata, 1024K init, 303K bss, 31528K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x408/0x7a8 with crng_init=0 [ 0.000000][ T0] trace event string verifier disabled [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 0.000003][ T0] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 0.000087][ T0] Switching to timer-based delay loop, resolution 6ns [ 0.001415][ T0] Console: colour dummy device 80x30 [ 0.001534][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666) [ 0.001599][ T0] pid_max: default: 32768 minimum: 301 [ 0.002181][ T0] LSM: Security Framework initializing [ 0.002487][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.002561][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.004731][ T0] CPU: Testing write buffer coherency: ok [ 0.008450][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.008952][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.009507][ T1] rcu: Hierarchical SRCU implementation. [ 0.011760][ T1] devtmpfs: initialized [ 0.020355][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.020443][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.076443][ T1] prandom32: self test passed (less than 6 bits correlated) [ 0.076514][ T1] prandom: seed boundary self test passed [ 0.082941][ T1] prandom: 100 self tests passed [ 0.082986][ T1] pinctrl core: initialized pinctrl subsystem [ 0.085547][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.086882][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.088655][ T1] audit: initializing netlink subsys (disabled) [ 0.091119][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.091667][ T16] audit: type=2000 audit(0.080:1): state=initialized audit_enabled=0 res=1 [ 0.091970][ T1] cpuidle: using governor ladder [ 0.092125][ T1] cpuidle: using governor menu [ 0.092916][ T1] Feroceon L2: Enabling L2 [ 0.092996][ T1] Feroceon L2: Cache support initialised. [ 0.107128][ T1] No ATAGs? [ 0.290407][ T1] raid6: int32x8 gen() 73 MB/s [ 0.460392][ T1] raid6: int32x8 xor() 46 MB/s [ 0.630243][ T1] raid6: int32x4 gen() 67 MB/s [ 0.800114][ T1] raid6: int32x4 xor() 48 MB/s [ 0.970147][ T1] raid6: int32x2 gen() 97 MB/s [ 1.140250][ T1] raid6: int32x2 xor() 58 MB/s [ 1.310338][ T1] raid6: int32x1 gen() 75 MB/s [ 1.480253][ T1] raid6: int32x1 xor() 41 MB/s [ 1.480278][ T1] raid6: using algorithm int32x2 gen() 97 MB/s [ 1.480299][ T1] raid6: .... xor() 58 MB/s, rmw enabled [ 1.480317][ T1] raid6: using intx1 recovery algorithm [ 1.480761][ T1] vgaarb: loaded [ 1.481627][ T1] SCSI subsystem initialized [ 1.482487][ T1] usbcore: registered new interface driver usbfs [ 1.482600][ T1] usbcore: registered new interface driver hub [ 1.482687][ T1] usbcore: registered new device driver usb [ 1.483014][ T1] pps_core: LinuxPPS API ver. 1 registered [ 1.483038][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 1.483090][ T1] PTP clock support registered [ 1.485973][ T1] clocksource: Switched to clocksource orion_clocksource [ 1.622666][ T1] VFS: Disk quotas dquot_6.6.0 [ 1.622834][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.657960][ T1] NET: Registered PF_INET protocol family [ 1.658264][ T1] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 1.659745][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 1.659820][ T1] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 1.659873][ T1] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 1.659915][ T1] TCP: Hash tables configured (established 1024 bind 1024) [ 1.660307][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.660424][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 1.660483][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 1.660797][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.661849][ T1] RPC: Registered named UNIX socket transport module. [ 1.661882][ T1] RPC: Registered udp transport module. [ 1.661901][ T1] RPC: Registered tcp transport module. [ 1.661918][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.661945][ T1] PCI: CLS 0 bytes, default 32 [ 1.662425][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.676582][ T29] Trying to unpack rootfs image as initramfs... [ 2.546000][ C0] random: fast init done [ 4.345538][ T29] Freeing initrd memory: 9936K [ 5.514256][ T1] Initialise system trusted keyrings [ 5.514372][ T1] Key type blacklist registered [ 5.514771][ T1] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 5.514957][ T1] zbud: loaded [ 5.517329][ T1] NFS: Registering the id_resolver key type [ 5.517395][ T1] Key type id_resolver registered [ 5.517418][ T1] Key type id_legacy registered [ 5.517487][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 5.517524][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 5.517547][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 5.517972][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 5.518750][ T1] fuse: init (API version 7.35) [ 5.519375][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 5.519723][ T1] orangefs_init: module version upstream loaded [ 5.519753][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 5.671299][ T1] xor: measuring software checksum speed [ 5.684586][ T1] arm4regs : 745 MB/sec [ 5.706655][ T1] 8regs : 446 MB/sec [ 5.721811][ T1] 32regs : 650 MB/sec [ 5.721835][ T1] xor: using function: arm4regs (745 MB/sec) [ 5.721866][ T1] async_tx: api initialized (async) [ 5.721900][ T1] Key type asymmetric registered [ 5.721920][ T1] Asymmetric key parser 'x509' registered [ 5.722138][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 5.722278][ T1] io scheduler bfq registered [ 6.010120][ T1] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 47 [ 6.010171][ T1] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 49 [ 6.010756][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 6.013709][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges: [ 6.013846][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000 [ 6.013916][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 6.013968][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 6.014449][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 6.014488][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 6.014526][ T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff]) [ 6.014559][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 6.014589][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 6.014764][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 6.016676][ T1] PCI: bus0: Fast back to back transfers disabled [ 6.016735][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 6.017106][ T1] pci 0000:01:00.0: [11ab:6281] type 00 class 0x058000 [ 6.017156][ T1] pci 0000:01:00.0: reg 0x10: [mem 0xf1000000-0xf10fffff] [ 6.017200][ T1] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x07ffffff] [ 6.017313][ T1] pci 0000:01:00.0: supports D1 D2 [ 6.047362][ T1] PCI: bus1: Fast back to back transfers disabled [ 6.047413][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 6.047749][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xebffffff] [ 6.047799][ T1] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0000000-0xe7ffffff] [ 6.047840][ T1] pci 0000:01:00.0: BAR 0: assigned [mem 0xe8000000-0xe80fffff] [ 6.047877][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 6.047912][ T1] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xebffffff] [ 6.048127][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 6.048955][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 6.107610][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 6.111496][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 6.177620][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 6.181899][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 6.184093][ T1] printk: console [ttyS0] disabled [ 6.184242][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 10416666) is a 16550A [ 7.220617][ T1] printk: console [ttyS0] enabled [ 7.238116][ T1] loop: module loaded [ 7.243182][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 7.254468][ T1] scsi host0: sata_mv [ 7.259401][ T1] scsi host1: sata_mv [ 7.263627][ T1] ata1: SATA max UDMA/133 irq 32 [ 7.268545][ T1] ata2: SATA max UDMA/133 irq 32 [ 7.275174][ T1] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it [ 7.284603][ T1] ONFI parameter recovery failed, aborting [ 7.290292][ T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 7.297345][ T1] nand: Hynix NAND 128MiB 3,3V 8-bit [ 7.302468][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 7.310782][ T1] Scanning device for bad blocks [ 7.400354][ T1] 5 cmdlinepart partitions found on MTD device orion_nand [ 7.407326][ T1] Creating 5 MTD partitions on "orion_nand": [ 7.413153][ T1] 0x000000000000-0x000000200000 : "u-boot" [ 7.419635][ T1] 0x000000200000-0x000000500000 : "uImage" [ 7.426029][ T1] 0x000000500000-0x000000800000 : "uImage2" [ 7.432440][ T1] 0x000000800000-0x000001000000 : "failsafe" [ 7.438995][ T1] 0x000001000000-0x000008000000 : "root" [ 7.446626][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 7.455139][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 7.493779][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 7.597899][ T42] ata1: SATA link down (SStatus 0 SControl F300) [ 7.937773][ T44] ata2: SATA link down (SStatus 0 SControl F300) [ 8.257521][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:04:28:15 [ 8.267184][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.274436][ T1] ehci-pci: EHCI PCI platform driver [ 8.279698][ T1] ehci-orion: EHCI orion driver [ 8.284719][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 8.291035][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 8.299678][ T1] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 8.336022][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 8.343154][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.16 [ 8.352142][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.360069][ T1] usb usb1: Product: EHCI Host Controller [ 8.365632][ T1] usb usb1: Manufacturer: Linux 5.16.5-kirkwood-tld-1 ehci_hcd [ 8.373046][ T1] usb usb1: SerialNumber: f1050000.ehci [ 8.379532][ T1] hub 1-0:1.0: USB hub found [ 8.384043][ T1] hub 1-0:1.0: 1 port detected [ 8.389892][ T1] usbcore: registered new interface driver usb-storage [ 8.397260][ T1] mousedev: PS/2 mouse device common for all mice [ 9.446039][ T1] rtc-mv f1010300.rtc: internal RTC not ticking [ 9.452422][ T1] i2c_dev: i2c /dev entries driver [ 9.458426][ T1] device-mapper: uevent: version 1.0.3 [ 9.464157][ T1] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com [ 9.473976][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 9.481281][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 9.488615][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 9.496031][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 9.502803][ T1] device-mapper: raid: Loading target version 1.15.1 [ 9.511360][ T1] hid: raw HID events driver (C) Jiri Kosina [ 9.517739][ T1] drop_monitor: Initializing network drop monitor service [ 9.525378][ T1] NET: Registered PF_INET6 protocol family [ 9.533314][ T1] Segment Routing with IPv6 [ 9.537803][ T1] RPL Segment Routing with IPv6 [ 9.542561][ T1] In-situ OAM (IOAM) with IPv6 [ 9.547338][ T1] NET: Registered PF_PACKET protocol family [ 9.553419][ T1] Key type dns_resolver registered [ 9.559366][ T1] registered taskstats version 1 [ 9.564164][ T1] Loading compiled-in X.509 certificates [ 9.571439][ T1] zswap: loaded using pool lzo/zbud [ 9.577409][ T1] Key type ._fscrypt registered [ 9.582119][ T1] Key type .fscrypt registered [ 9.586866][ T1] Key type fscrypt-provisioning registered [ 9.601429][ T1] Key type big_key registered [ 9.654623][ T1] Key type encrypted registered [ 9.839979][ T104] "cryptomgr_test" (104) uses obsolete ecb(arc4) skcipher [ 17.131187][ T1] Freeing unused kernel image (initmem) memory: 1024K [ 17.157227][ T1] Checked W+X mappings: passed, no W+X pages found [ 17.163601][ T1] Run /init as init process Loading, please wait... Starting version 247.3-6 [ 18.404978][ T143] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [ 18.715480][ T29] mvsdio f1090000.mvsdio: Got CD GPIO [ 18.783362][ T40] mmc0: host does not support reading read-only switch, assuming write-enable [ 18.802209][ T40] mmc0: new high speed SDHC card at address aaaa [ 19.153701][ T143] mmcblk0: mmc0:aaaa SL08G 7.40 GiB [ 19.171389][ T143] mmcblk0: p1 Begin: Loading essential drivers ... [ 19.463858][ T154] netpoll: netconsole: local port 6666 [ 19.469424][ T154] netpoll: netconsole: local IPv4 address 10.11.10.248 [ 19.478010][ T154] netpoll: netconsole: interface 'eth0' [ 19.483401][ T154] netpoll: netconsole: remote port 6666 [ 19.488815][ T154] netpoll: netconsole: remote IPv4 address 10.11.10.15 [ 19.495505][ T154] netpoll: netconsole: remote ethernet address ff:ff:ff:ff:ff:ff [ 19.503087][ T154] netpoll: netconsole: device eth0 not up yet, forcing it [ 24.286005][ T154] netpoll: netconsole: timeout waiting for carrier [ 24.297849][ T154] printk: console [netcon0] enabled [ 24.302923][ T154] netconsole: network logging started done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.36.1 [/sbin/fsck.ext4 (1) -- /dev/mmcblk0p1] fsck.ext4 -a -C0 /dev/mmcblk0p1 rootfs: clean, 20806/262144 files, 381015/1048576 blocks done. [ 34.685677][ T173] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none. done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.96 booting Using makefile-style concurrent boot in runlevel S. Setting hostname to 'debian'...done. Starting fake hwclock: loading system time. Wed Mar 23 21:27:38 UTC 2022 Starting hotplug events dispatcher: systemd-udevd. Synthesizing the initial hotplug events (subsystems)...done. Synthesizing the initial hotplug events (devices)...done. Waiting for /dev to be fully populated...[ 39.011715][ T371] orion_wdt: Initial timeout 25 sec [ 39.775182][ T362] marvell-cesa f1030000.crypto: CESA device successfully registered done. Not activating swap on swapfile. ... (warning). [ 41.128627][ T512] EXT4-fs (mmcblk0p1): re-mounted. Opts: errors=remount-ro. Quota mode: none. Will now check all file systems. /dev/sda1: skipping nonexistent device Checking all file systems. LABEL=rootfs is mounted Done checking file systems. Log is being saved in /var/log/fsck/checkfs if that location is writable. Cleaning up temporary files...Cleaning /tmp...done. /tmp. [ 43.679464][ T796] Adding 524284k swap on /swapfile. Priority:-2 extents:2 across:532476k SSFS Will now mount local filesystems:. Will now activate swapfile swap, if any:swapon: /swapfile: found signature [pagesize=4096, signature=swap] swapon: /swapfile: pagesize=4096, swapsize=536870912, devsize=536870912 swapon /swapfile done. Checking minimum space in /tmp...done. Cleaning up temporary files.... Starting Setting kernel variables: sysctl. [ 44.451901][ T888] random: dd: uninitialized urandom read (512 bytes read) Initializing random number generator...done. Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:25:31:04:28:15 Sending on LPF/eth0/00:25:31:04:28:15 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 19 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 17 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 13 No DHCPOFFERS received. No working leases in persistent database - sleeping. done. Starting RPC port mapper daemon: rpcbind. Starting NFS common utilities: statd idmapd. Cleaning up temporary files.... INIT: Entering runlevel: 2 Using makefile-style concurrent boot in runlevel 2. Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1058 (syslogd) . Starting NFS common utilities: statd idmapd. [ 109.445655][ T1108] random: dbus-daemon: uninitialized urandom read (12 bytes read) [ 109.491510][ T1108] random: dbus-daemon: uninitialized urandom read (12 bytes read) Starting system message bus: dbus. [ 109.576144][ C0] random: crng init done Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. Not starting NFS kernel daemon: no exports. ... (warning). Starting NTP server: ntpd. Starting OpenBSD Secure Shell server: sshd. Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1099 (klogd) . Running local boot scripts (/etc/rc.local) . Debian GNU/Linux 11 debian ttyS0 debian login: root Password: Linux debian 5.16.5-kirkwood-tld-1 #1.0 PREEMPT Sat Feb 5 20:02:03 PST 2022 armv5tel The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. Last login: Wed Mar 23 21:27:29 GMT 2022 on ttyS0 debian Pogoplug v4 Linux version 5.16.5-kirkwood-tld-1 (root@tldDebianVM) (arm-linux-gnueabi-gcc (Ubuntu 9.3.0-17ubuntu1~20.04) 9.3.0, GNU ld (GNU Binutils for Ubuntu) 2.34) #1.0 PREEMPT Sat Feb 5 20:02:03 PST 2022 Debian 11.2 Wed Mar 23 21:29:06 GMT 2022 up 2 minutes root@debian:~#
Re: Pogo V4 - USB3 ports dead in Debian March 23, 2022 06:01PM |
Admin Registered: 13 years ago Posts: 18,613 |
Re: Pogo V4 - USB3 ports dead in Debian March 23, 2022 06:39PM |
Admin Registered: 13 years ago Posts: 18,613 |
Quote
Linux version 5.15.5-kirkwood-tld-1 (root@tldDebianVM) (arm-linux-gnueabi-gcc (Ubuntu 9.3.0-17ubuntu1~20.04) 9.3.0, GNU ld (GNU Binutils for Ubuntu) 2.34) #1.0 PREEMPT Sun Dec 5 14:47:42 PST 2021
[ 15.495965] xhci_hcd 0000:01:00.0: assign IRQ: got 37 [ 15.496099] xhci_hcd 0000:01:00.0: enabling bus mastering [ 15.496128] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 15.502074] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2 [ 15.512026] xhci_hcd 0000:01:00.0: hcc params 0x200073a1 hci version 0x100 quirks 0x0000000000080010 [ 15.521899] xhci_hcd 0000:01:00.0: enabling Mem-Wr-Inval [ 15.545433] usb usb2: Manufacturer: Linux 5.15.5-kirkwood-tld-1 xhci-hcd [ 15.569435] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 15.575461] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3 [ 15.583595] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed [ 15.622466] usb usb3: Manufacturer: Linux 5.15.5-kirkwood-tld-1 xhci-hcd [ 330.930889] usb 3-1: new SuperSpeed USB device number 2 using xhci_hcd
Re: Pogo V4 - USB3 ports dead in Debian March 25, 2022 04:31AM |
Registered: 12 years ago Posts: 33 |
Re: Pogo V4 - USB3 ports dead in Debian March 26, 2022 04:06PM |
Admin Registered: 13 years ago Posts: 18,613 |