Installation of Rootfs Debian-5.13.8-mvebu-tld-1-rootfs-bodhi on WD EX2 Ultra June 27, 2022 03:21AM |
Registered: 2 years ago Posts: 10 |
Re: Installation of Rootfs Debian-5.13.8-mvebu-tld-1-rootfs-bodhi on WD EX2 Ultra June 27, 2022 03:51AM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Installation of Rootfs Debian-5.13.8-mvebu-tld-1-rootfs-bodhi on WD EX2 Ultra June 27, 2022 04:17AM |
Registered: 2 years ago Posts: 10 |
Re: Installation of Rootfs Debian-5.13.8-mvebu-tld-1-rootfs-bodhi on WD EX2 Ultra June 27, 2022 03:22PM |
Admin Registered: 13 years ago Posts: 18,821 |
Re: Installation of Rootfs Debian-5.13.8-mvebu-tld-1-rootfs-bodhi on WD EX2 Ultra June 28, 2022 03:48AM |
Registered: 2 years ago Posts: 10 |
BootROM - 1.73 Booting from NAND flash General initialization - Version: 1.0.0 Detected Device ID 6820 High speed PHY - Version: 2.0 Load WD GrandTeton Serdes Config: board SerDes lanes topology details: | Lane # | Speed | Type | -------------------------------- | 0 | 06 | SATA0 | | 1 | 05 | PCIe0 | | 2 | 06 | SATA1 | | 3 | 05 | USB3 HOST1 | | 4 | 05 | USB3 HOST0 | | 5 | 00 | SGMII2 | -------------------------------- PCIe, Idx 0: detected no link High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.26.0 mvSysEnvGetTopologyUpdateInfo: TWSI Read failed DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01_v1.04 (Jun 27 2022 - 15:51:17) Marvell version: 2014_T3.0p6 mvBoardIdIndexGet(boardId) = 1 Board: GrandTeton DB6820 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 1 GiB Map: Code: 0x3fece000:0x3ff96000 BSS: 0x3ffef654 Stack: 0x3f9cdf20 Heap: 0x3f9ce000:0x3fece000 raise: Signal # 8 caught raise: Signal # 8 caught U-Boot Environment: 0x00000000:0x00080000 (NAND) NAND: ID: daad ,256 MiB MMC: mv_sdh: 0 PCI-e 0: Detected No Link. USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Creating 1 MTD partitions on "nand0": 0x00000f500000-0x00000ff00000 : "mtd=7" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=7" UBI: MTD device size: 10 MiB UBI: number of good PEBs: 80 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 32 UBI: total number of reserved PEBs: 48 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 4/1 UBIFS: mounted UBI device 0, volume 0, name "reserve2" UBIFS: mounted read-only UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs) UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: LZO UBIFS: reserved for root: 200807 bytes (196 KiB) Loading file '/mac_addr' to addr 0x02000000 with size 18 (0x00000012)... Done Set lan 2 WakeOnLan ok Enable HD1 Enable HD2 Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | In-Band | | egiga1 | RGMII | In-Band | | egiga2 | SGMII | 0x00 | egiga0, egiga1, egiga2 [PRIME] Hit any key to stop autoboot: 0 Marvell>> printenv CASset=max MALLOC_len=5 MPmode=SMP autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=root=/dev/ram console=ttyS0,115200 bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bol bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=nand read.e 0x02000020 0x0500000 0x0500000; nand read.e 0x2900000 0x0a00000 0x0500000; bootm 0x020000 bootcmd_auto=stage_boot $boot_order bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtd; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root ; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootcmd_stock=echo Booting from stock ... ; run set_bootargs_stock; printenv bootargs; nand read.e 0xa00000 0 bootcmd_usb=echo Booting from USB ...; usb start; run usb_set_bootargs; if run load_image; then if run load_p bootdelay=1 bootdev=usb cacheShare=no console=console=ttyS0,115200 device=0:1 device_partition=0:1 disaMvPnp=no eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:dd:2b:4e eth1mtu=1500 eth2addr=00:50:43:dd:7a:4e eth2mtu=1500 eth3addr=00:50:43:2b:7a:dd eth3mtu=1500 ethact=egiga2 ethaddr=00:50:43:7a:2b:4e ethmtu=1500 ethprime=egiga2 fdt_addr=2040000 fdt_skip_update=no fdtaddr=0x1000000 fdtfile=armada-38x-modular.dtb filesize=12 ide_path=/ image_name=uImage initrd_name=uInitrd ipaddr=192.168.11.110 kernel_addr_r=2080000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 load_image=echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage load_image_addr=0x02000020 load_initrd=echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x2900000 loadaddr=0x02000000 loads_echo=0 mtddevname=u-boot mtddevnum=0 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescu) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:4e:7a:dd nandEcc=nfcConfig=4bitecc netbsd_en=no netmask=255.255.255.0 netretry=no partition=nand0,0 pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rootpath=/srv/nfs/ sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scr serverip=192.168.11.114 set_bootargs_stock=setenv bootargs root=/dev/ram console=ttyS0,115200 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw i; stderr=serial stdin=serial stdout=serial usb0Mode=host usbActive=1 usbType=3 usb_set_bootargs=setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=" vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 4107/524284 bytes Marvell>>
Re: Installation of Rootfs Debian-5.13.8-mvebu-tld-1-rootfs-bodhi on WD EX2 Ultra June 28, 2022 02:48PM |
Registered: 2 years ago Posts: 10 |
Marvell>> setenv bootcmd_sata 'scsi reset;ext2load scsi 0:1 0x500000 /boot/uImage;ext2load scsi 0:1 0xa00000 /boot/uInitrd;bootm 0x500000 0xa00000' Marvell>> setenv set_bootargs_sata 'setenv bootargs "root=/dev/sda1 console=ttyS0,115200 rootdelay=10 usbcore.autosuspend=-1 $mtdparts earlyprintk=serial raid=noautodetect"' Marvell>> setenv bootcmd 'run set_bootargs_sata;run bootcmd_sata' Marvell>> printenv bootcmd Marvell>> run bootcmd