Fresh Debian install hangs at "Starting kernel ..." (USB/HDD) [solved]

Hi,

Long time user of a Seagate Dockstar which was used to run Debian on an USB stick, then forgotten a few months in a pile of stuffs after having moved, I wanted today to do a fresh install using an hard drive instead of the USB stick, and I encounter some issues while trying to boot the DS with this hard drive, after having succesfully debootstrapped Debian from Jeff's script.

The issue is: bootup with the HDD hangs at "Starting kernel ..." even if I wait for a very long time (more than 1 hour ^^ while looking for help on the web)

I have exactly the same problem if using an usb stick (I tried with the previous one that worked, but which I reinstalled the same way as the HDD (Jeff's script)).

This DS has Jeff's U-Boot since the beginning, it was never modified meanwhile.

I looked all over the web (and this forum) for ideas of solutions, but most of the topics or article I find had another issue or were going through complicated manipulations of mtd's partitions...

It was working a few month ago, now it won't for a new install, so I am looking for any idea to troubleshoot this further.

Here is the output of the netconsole:

U-Boot 2010.09 (Oct 23 2010 - 11:49:22)
Marvell-Dockstar/Pogoplug by Jeff Doozan
Hit any key to stop autoboot:  0
(Re)start USB...
USB:   Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/rescueme" from usb device 0:1 (usbda1)
** File not found /rescueme
reading /rescueme.txt

** Unable to read "/rescueme.txt" from usb 0:1 **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=3"
UBI: MTD device size:            219 MiB
UBI: number of good PEBs:        1752
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     0
UBI: available PEBs:             1731
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1 bytes read
Found bootable drive on usb 0:1
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1433640 bytes read
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
4739059 bytes read
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-2.6.32-5-kirkwood
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1433576 Bytes = 1.4 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
   Image Name:   initramfs-2.6.32-5-kirkwood
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    4738995 Bytes = 4.5 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

And my fw_printenv output

Pogoplug:/tmp$ fw_printenv
ethact=egiga0
bootdelay=3
baudrate=115200
mainlineLinux=yes
console=ttyS0,115200
led_init=green blinking
led_exit=green off
led_error=orange blinking
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
mtdids=nand0=orion_nand
partition=nand0,2
stdin=serial
stdout=serial
stderr=serial
rescue_installed=0
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done
usb_scan_list=1 2 3 4
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_init=run usb_scan
usb_device=0:1
usb_root=/dev/sda1
usb_rootdelay=10
usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
ethaddr=00:10:75:1A:71:42
arcNumber=2097
usb_rootfstype=ext2
serverip=192.168.1.100
ipaddr=192.168.1.111
if_netconsole=ping $serverip
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
preboot=run if_netconsole start_netconsole

Edited 3 time(s). Last edit at 05/14/2012 09:59AM by Zrk.

Ok, nevermind I think I found the issue...

From my previous installation (about 1 year ago) I set up the rootfs on my usb key to ext3 and set accordingly fw_setenv usb_rootfstype ext3

I switched back to usb_rootfstype ext2 and now it boot.