Welcome! Log In Create A New Profile

Advanced

oxnas(OX820)/Medion from openWRT to debian

Posted by snickerweb 
oxnas(OX820)/Medion from openWRT to debian
May 15, 2023 08:32AM
Hi,
I have set up openWRT on my oxnas according to these instructions. Serial connection is available.
Unfortunately the Samba performance is very bad (~10MB/s).

Now I would like to try Debian.
Due to lack of Linux experience/English knowledge I would need a little support. Which of the instructions in the forum can I use to get from openWRT to debian?

uBoot:
I would like to update the uBoot for easy USB boot.
https://forum.doozan.com/read.php?3,16017 <-- This is the right one for me? If I understand correctly the uBoot is replaced in the NAND. Is this the base system I can abort on boot?

will the entries be replaced or supplemented?
root@ChrisNAS:~# cat /etc/fw_env.config change no Problem
/dev/mtd2 0x0 0x20000 0x20000 1
root@ChrisNAS:~# cat /proc/mtd could not write with nano
dev:    size   erasesize  name
mtd0: 00040000 00020000 "stage1"
mtd1: 00380000 00020000 "u-boot"
mtd2: 00080000 00020000 "u-boot-env"
mtd3: 009c0000 00020000 "kernel"
mtd4: 07200000 00020000 "ubi"


Debian:
How is Debian installed. USB stick or can that also be in the NAND like openWRT?
Debian: https://forum.doozan.com/read.php?2,16044 <-- am I in the right place?

Can someone explain me roughly step by step how to get from openWRT to Debian?

Thanks a lot
Chris



Edited 2 time(s). Last edit at 05/15/2023 09:37AM by snickerweb.
Re: oxnas(OX820)/Medion from openWRT to debian
May 15, 2023 06:45PM
snickerweb,

Quote

uBoot:
I would like to update the uBoot for easy USB boot.
https://forum.doozan.com/read.php?3,16017 <-- This is the right one for me? If I understand correctly the uBoot is replaced in the NAND. Is this the base system I can abort on boot?

Debian:
How is Debian installed. USB stick or can that also be in the NAND like openWRT?
Debian: https://forum.doozan.com/read.php?2,16044 <-- am I in the right place?

Those are correct links to install new u-boot and Debian.

When you install new u-boot, it should be considered a new installation and you will no longer be able to boot OpenWrt. Later, you can go further and update the envs to dual boot Debian and OpenWrt. But that's not a sure thing. Assuming you will wipe out OpenWrt.

The Debian rootfs should be created on USB drive. It is not possible to run Debian on NAND flash (the flash storage is too small).

With all that said, the new u-boot was created for the Pogo V3 boxes. So there is a small chance that it will not work for this Medion box. The Debian rootfs has been installed by other users, and it was shown to work OK with this Medion box. But I did not have a report that this new u-boot was working without problem for Medion box. So keep that in mind.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Re: oxnas(OX820)/Medion from openWRT to debian
May 16, 2023 02:09AM
thanks for your answer.

Is the way:
1. Install new UBoot in NAND
2. Install openWRT again in NAND
3. Install debian on USB

Can I do first Step (1.png) in the existing openWRT?

"1. Backup your current uImage and uInitrd and other kernel files. In the /boot directory"
on openWRT there is no /boot directory (2.png)



Edited 1 time(s). Last edit at 05/16/2023 02:23AM by snickerweb.
Attachments:
open | download - 1.png (85.1 KB)
open | download - 2.png (50.7 KB)
Re: oxnas(OX820)/Medion from openWRT to debian
May 16, 2023 04:02PM
Not really.

1. Install debian on USB
2. Install new UBoot in NAND
3. After Debian is running on USB rootfs, check out everything is OK.
4. Install openWRT again in NAND.

That's the cleanest way to do it. After you are running Debian, install openWRT again in NAND using this insruction:
https://forum.doozan.com/read.php?4,132635

=====

There is another appraoch: I might be able to help you booting Debian with the currently installed OpenWrt u-boot in your box. If you'd like to try this approach:


1. Create the Debian rootfs on USB using Debian-4.14.180-oxnas-tld-1-rootfs-bodhi.tar.bz2.
2. Plug this new rootfs in the USB port.
3. Power up, interrupt serial console at countdown,and

printenv
usb start
help
And post the entire serial console log here (copy/paste what on your serial console terminal). Don't post pictures, I need the text log.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Re: oxnas(OX820)/Medion from openWRT to debian
May 16, 2023 04:04PM
Quote
U-Boot 1.1.2 (Jun 24 2011 - 09:41:57)

U-Boot code: 60D00000 -> 60D1A94C BSS: -> 60D1F004
RAM Configuration:
Bank #0: 60000000 128 MB
SRAM Configuration:
64KB at 0x50000000
NAND:128 MiB
In: serial
Out: serial
Err: serial
Setting Linux mem= boot arg value
Hit any key to stop autoboot: 0
$ printenv
bootdelay=2
baudrate=115200
ipaddr=192.168.50.100
autoload=n
netmask=255.255.0.0
bootfile="uImage"
load_nand=nboot 61000000 0 440000
boot=bootm 61000000
boot_nand=run load_nand boot
MODEL_ID=AB03
PRODUCT_NAME=STG-212
VENDOR_NAME=MitraStar Technology Corp.
ethaddr=00:11:41:30:F2:34
boot_stage2=nand read 0x64000000 0x440000 0x90000 ; go 64000000
bootcmd=nboot 60500000 0 440000; bootm
serverip=192.168.178.6
stdin=serial
stdout=serial
stderr=serial
bootargs= console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=128M poweroutage=yes

Environment size: 556/131068 bytes
Unknown command 'usbsry 'help'
$ usb start
Unknown command 'usb' - try 'help'
$ help
? - alias for 'help'
base - print or set address offset
bdinfo - print Board Info structure
bootm - boot application image from memory
bootp - boot image via network using BootP/TFTP protocol
cmp - memory compare
cp - memory copy
crc32 - checksum calculation
echo - echo args to console
exit - exit script
go - start application at address 'addr'
help - print online help
iminfo - print header information for application image
ledfail - Extinguish (0) or light (1) failure LED
loop - infinite loop on address range
md - memory display
mm - memory modify (auto-incrementing)
mtest - simple RAM test
mw - memory write (fill)
nand - NAND sub-system
nboot - boot from NAND device
nm - memory modify (constant address)
nwboot - NAND Write boot information
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset - Perform RESET of the CPU
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv - set environment variables
test - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
version - print monitor version




Edited 2 time(s). Last edit at 05/16/2023 04:28PM by snickerweb.
Re: oxnas(OX820)/Medion from openWRT to debian
May 16, 2023 05:31PM
debian USB stick I have done. uImage is with ox820-stg212.dtb.
"USB Start" boot does not work. I do not know how to boot from the stick.



Edited 1 time(s). Last edit at 05/16/2023 05:33PM by snickerweb.
Re: oxnas(OX820)/Medion from openWRT to debian
May 16, 2023 10:48PM
Ok, looks like you'll have to install new u-boot and Debian first. Do it only if you are absolutely want to run Debian, and don't mind if it does not work then you have to run the HDD rescue.

Quote

1. Install debian on USB
2. Install new UBoot in NAND
3. After Debian is running on USB rootfs, check out everything is OK.
4. Install openWRT again in NAND.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Re: oxnas(OX820)/Medion from openWRT to debian
May 17, 2023 01:24AM
My home server and my raspi both have Debian. That's why I prefer it to openWRT anyway.
I will create a rescue disk. The internal SATA is empty anyway.

Do you think there is a speed advantage in samba transfer (win11 <-> oxnas) if debian is installed on the disk?

u-Boot installation can I do from openWRT?

Tonight tasks ;)
- rescue disk
- u-boot

Thanks a lot for the support
Re: oxnas(OX820)/Medion from openWRT to debian
May 17, 2023 05:03PM
rescue disk I have created.
I can get into the U-Boot of the disk, but not into debian.
I put ox820-stg212.dtb in the dtb folder and rename it to ox820-pogoplug-pro.dtb

U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
  Boot device: SATA
Attempting to set PLLA to 850 MHz ...
  plla_ctrl0 : 0000020a
  plla_ctrl1 : 00330000
  plla_ctrl2 : 0065008b
  plla_ctrl3 : 000000f1

PLLA Set
Bus 0: OK
  Device 0:
** File not found /boot/bootargs.bin **


U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS

DRAM:  128 MiB
IDE:   Bus 0: OK
  Device 0: Model: TOSHIBA MK1661GSYN Firm: MH000K Ser#:  42B4P0VTT
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 152627.8 MB = 149.0 GB (312581808 x 512)
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:
Led:    GREEN
mii0
Main Loop
Hit any key to stop autoboot:  0
ide - IDE sub-system

Usage:
ide reset - reset IDE controller
ide info  - show available IDE devices
ide device [dev] - show or set current device
ide part [dev] - print partition table of one or all IDE devices
ide read  addr blk# cnt
ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#'
    to/from memory address `addr'
2212156 bytes read in 474 ms (4.4 MiB/s)
## Booting kernel from Legacy Image at 60500000 ...
   Image Name:   Linux-2.6.31.14_OX820_1.2_shv
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2212092 Bytes = 2.1 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Led:    GREEN

Starting kernel ...

Uncompressing Linux....................................................................................................................................... done, booting the kernel.
[    0.000000] Linux version 2.6.31.14_OX820_1.2_shv (root@plug2) (gcc version 4.4.5 (Debian 4.4.5-8) ) #1 SMP Fri Oct 4 11:38:10 CEST 2013
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5387f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[    0.000000] Machine: Oxsemi NAS
[    0.000000] 1 memory region
[    0.000000] Ignoring unrecognised tag 0x00000000
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: root=/dev/sda2 rootfstype=ext3 console=ttyS0,115200 mem=128M
[    0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 128MB = 128MB total
[    0.000000] Memory: 125368KB available (3816K code, 304K data, 132K init, 0K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:96
[    0.000000] OX820_RPS_init_irq: interrupts 64 to 96
[    0.010000] Console: colour dummy device 80x30
[    0.010000] console [ttyS0] enabled
[    0.020000] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[    0.230000] Security Framework initialized
[    0.230000] Mount-cache hash table entries: 512
[    0.240000] CPU: Testing write buffer coherency: ok
[    0.240000] Calibrating local timer... 425.50MHz.
[    0.310000] CPU1: Booted secondary processor
[    0.410000] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[    0.620000] Brought up 2 CPUs
[    0.630000] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[    0.640000] NET: Registered protocol family 16
[    0.640000] Number of DMA channels = 4, version = 4
[    0.650000] Reserving a DMA channel for DirectRAID
[    0.650000] Allocating 389 SRAM generic DMA descriptors"



OX820 # printenv
dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr
autoload=no
baudrate=115200
bootargs=console=ttyS0,115200n8
bootcmd=run dt_bootcmd_ide
bootdelay=3
console=console=ttyS0,115200n8
dt_bootcmd_ide=ide start; run dt_ide_bootcmd; ide stop; reset
dt_bootcmd_usb=usb start; run dt_usb_bootcmd; usb stop; reset
dt_bootm=bootm $uimage_addr $uinitrd_addr $dtb_addr
dt_ide_boot=run dt_ide_load_uimage; run dt_ide_load_initrd; run dt_ide_load_dtb; run dt_bootm
dt_ide_bootcmd=run ide_set_bootargs; run dt_sata_boot
dt_ide_load_dtb=ext2load ide 0:1 $dtb_addr /boot/dts/ox820-pogoplug-pro.dtb
dt_ide_load_initrd=ext2load ide 0:1 $uinitrd_addr /boot/uInitrd
dt_ide_load_uimage=ext2load ide 0:1 $uimage_addr /boot/uImage
dt_load_dtb=ext2load usb 0:1 $dtb_addr /boot/dts/ox820-pogoplug-pro.dtb
dt_load_initrd=ext2load usb 0:1 $uinitrd_addr /boot/uInitrd
dt_load_uimage=ext2load usb 0:1 $uimage_addr /boot/uImage
dt_sata_boot=ext2load ide 0:1 $uimage_addr /boot/uImage_2.6.31.14_OX820_1.2_shv.Pro; bootm $uimage_addr
dt_usb_boot=run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm
dt_usb_bootcmd=run usb_set_bootargs; run dt_usb_boot
dtb_addr=0x62c00000
ethact=mii0
ethaddr=00:25:31:01:C6:76
ide_set_bootargs=setenv bootargs root=/dev/sda2 rootfstype=ext3 console=ttyS0,115200 mem=128M
if_netconsole=ping $serverip
ipaddr=192.168.0.100
mtdids=nand0=41000000.nand
mtdparts=mtdparts=41000000.nand:14m(boot),-(data)
preboot_nc=run if_netconsole start_netconsole
sata_bootcmd=run usb_set_bootargs; run sata_boot
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version
stderr=serial
stdin=serial
stdout=serial
uimage_addr=0x60500000
uinitrd_addr=0x60e00000
usb_device=0:1
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=/dev/sda1 rootdelay=10

Environment size: 1898/16380 bytes"



Edited 3 time(s). Last edit at 05/18/2023 01:27PM by snickerweb.
Re: oxnas(OX820)/Medion from openWRT to debian
May 18, 2023 01:09PM
U-Boot I tried a few things.
I just do not know how to flash the U-Boot without being able to boot debian first.

I also tested archlinux but is the same:
in the log it always reports that it does not find /dev/sdx although USB storage is detected.
[    1.820000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.830000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.830000] usb usb1: Product: OXNAS EHCI Host Controller
[    1.840000] usb usb1: Manufacturer: Linux 2.6.31.6_SMP_820 ehci_hcd
[    1.850000] usb usb1: SerialNumber: usb
[    1.850000] usb usb1: configuration #1 chosen from 1 choice
[    1.860000] hub 1-0:1.0: USB hub found
[    1.860000] hub 1-0:1.0: 2 ports detected
[    1.870000] Initializing USB Mass Storage driver...
[    1.870000] usbcore: registered new interface driver usb-storage
[    1.880000] USB Mass Storage support registered."
[    1.910000] VFS: Cannot open root device \"sda1\" or unknown-block(0,0)
[    1.920000] Please append a correct \"root=\" boot option; here are the available partitions:
[    1.930000] 1f00          131072 mtdblock0 (driver?)
[    1.930000] 1f01           14336 mtdblock1 (driver?)
[    1.940000] 1f02          116736 mtdblock2 (driver?)
[    1.940000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)"


i tested /dev/sdX but openWRT say my stick is sda1

When I try to upgrade U-Boot over openWRT I can't change

cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00e00000 00020000 "boot"
mtd1: 07200000 00020000 "data"


with "nano /proc/mtd"



Edited 2 time(s). Last edit at 05/18/2023 01:28PM by snickerweb.
Re: oxnas(OX820)/Medion from openWRT to debian
May 18, 2023 03:37PM
snickerweb,

> I also tested archlinux but is the same:
> in the log it always reports that it does not find
> /dev/sdx although USB storage is detected.

> i tested /dev/sdX but openWRT say my stick is
> sda1

/dev/sdx meaning it could be /dev/sda1, /dev/sdb1,.... x here is a shorthand to say: whatever the drive letter is, replace x with that.

> with "nano /proc/mtd"

/proc/mtd is the list of mtds that the kernel determines during boot. You can not change it.

=====

Your HDD rootfs preparation probably was not done correctly. Is it on the 2nd partition of the HDD?

Also, when you boot with the rescue HDD, unplug all USB drives before booting.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Re: oxnas(OX820)/Medion from openWRT to debian
May 18, 2023 03:51PM
My guess is that it did not mount USB as /dev/sd. With X I meant I tried everything sda,sda1,....
rootfs from the hddrescue is on sda1. I have changed bootargs.
same stop by
[    0.650000] Allocating 389 SRAM generic DMA descriptors


On another HDD I have successfully started archlinux. :)
uimage via tftp and rootfs on hdd

from here I should now be able to install the UBoot 2015. I try this tutorial:
https://forum.doozan.com/read.php?2,28208,page=1



Edited 2 time(s). Last edit at 05/18/2023 03:57PM by snickerweb.
Re: oxnas(OX820)/Medion from openWRT to debian
May 18, 2023 04:53PM
I was sweating quite a bit.
It worked :)
U-Boot 2015.10-tld-2 (Oct 21 2017 - 22:00:02 -0700)
OXNAS OX820
DRAM:  128 MiB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   dwmac.40400000
Hit any key to stop autoboot:  0

Nächster Schritt Debian ;)
Re: oxnas(OX820)/Medion from openWRT to debian
May 18, 2023 05:01PM
Quote

On another HDD I have successfully started archlinux. :)

It worked :)
U-Boot 2015.10-tld-2 (Oct 21 2017 - 22:00:02 -0700)

Cool!

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Re: oxnas(OX820)/Medion from openWRT to debian
May 18, 2023 05:39PM
debain however still makes problems from usb with the new u-boot

U-Boot SPL 2013.10-tld-4 (Sep 07 2014 - 14:10:12)
  Boot device: NAND
Attempting to set PLLA to 850 MHz ...
  plla_ctrl0 : 0000020a
  plla_ctrl1 : 00330000
  plla_ctrl2 : 0065008b
  plla_ctrl3 : 000000f1

PLLA Set


U-Boot 2015.10-tld-2 (Oct 21 2017 - 22:00:02 -0700)
OXNAS OX820

DRAM:  128 MiB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   dwmac.40400000
Hit any key to stop autoboot:  0
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found

Reset IDE: SATA PHY not ready for device 0
ide_preinit failed

Partition Map for USB device 0  --   Partition Type: DOS

Part    Start Sector    Num Sectors     UUID            Type
  1     2048            4194304         54e074cd-01     83
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **

no IDE devices available
running scan_disk ...
Scan device usb
device usb 0:1
1 bytes read in 210 ms (0 Bytes/s)
Found bootable drive on usb 0
loading uImage ...
4600448 bytes read in 385 ms (11.4 MiB/s)
loading uInitrd ...
6464907 bytes read in 393 ms (15.7 MiB/s)
loading DTB /boot/dts/ox820-pogoplug-pro.dtb ...
9032 bytes read in 216 ms (40 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
   Image Name:   Linux-4.14.180-oxnas-tld-1
   Created:      2020-05-15   3:58:34 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4600384 Bytes = 4.4 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 60e00000 ...
   Image Name:   initramfs-4.14.180-oxnas-tld-1
   Created:      2020-05-15   3:58:49 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    6464843 Bytes = 6.2 MiB
   Load Address: 60000000
   Entry Point:  60000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
   Booting using the fdt blob at 0x62c00000
   Loading Kernel Image ... OK
   Loading Ramdisk to 677fc000, end 67e2654b ... OK
   Loading Device Tree to 677f6000, end 677fb347 ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.180-oxnas-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6)) #1 SMP PREEMPT Wed May 13 02:38:34 PDT 2020
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Pogoplug V3 Pro
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] random: get_random_bytes called from start_kernel+0x84/0x3f8 with crng_init=0
[    0.000000] percpu: Embedded 15 pages/cpu s29548 r8192 d23700 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data)
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 112712K/131072K available (7168K kernel code, 199K rwdata, 1524K rodata, 1024K init, 245K bss, 18360K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0800000   (8160 kB)
[    0.000000]       .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
[    0.000000]       .data : 0xc0b00000 - 0xc0b31f68   ( 200 kB)
[    0.000000]        .bss : 0xc0b383b8 - 0xc0b757c0   ( 246 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Tasks RCU enabled.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] FPGA IRQ chip 0 "interrupt-controller" @ c8804000, 32 irqs, parent IRQ: 16
[    0.000015] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[    0.000046] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[    0.000061] timer_oxnas_rps: Registered clocksource rate 390625Hz
[    0.000084] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500
[    0.000232] GIC: PPI13 is secure or misconfigured
[    0.000286] GIC: PPI13 is secure or misconfigured
[    0.000450] Console: colour dummy device 80x30
[    0.000496] Calibrating delay loop... 339.14 BogoMIPS (lpj=1695744)
[    0.050378] pid_max: default: 32768 minimum: 301
[    0.050649] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.050677] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.051573] CPU: Testing write buffer coherency: ok
[    0.090439] Setting up static identity map for 0x60100000 - 0x60100038
[    0.110341] Hierarchical SRCU implementation.
[    0.150341] smp: Bringing up secondary CPUs ...
[    0.220449] GIC: PPI13 is secure or misconfigured
[    0.280627] smp: Brought up 1 node, 2 CPUs
[    0.280660] SMP: Total of 2 processors activated (678.29 BogoMIPS).
[    0.281377] devtmpfs: initialized
[    0.286801] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.286835] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.287170] prandom: seed boundary self test passed
[    0.291463] prandom: 100 self tests passed
[    0.291486] pinctrl core: initialized pinctrl subsystem
[    0.292198] NET: Registered protocol family 16
[    0.293811] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.296156] cpuidle: using governor ladder
[    0.296230] cpuidle: using governor menu
[    0.314895] vgaarb: loaded
[    0.315402] SCSI subsystem initialized
[    0.316139] usbcore: registered new interface driver usbfs
[    0.316231] usbcore: registered new interface driver hub
[    0.316382] usbcore: registered new device driver usb
[    0.316590] pps_core: LinuxPPS API ver. 1 registered
[    0.316605] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.316641] PTP clock support registered
[    0.317667] clocksource: Switched to clocksource oxnas_rps_clocksource_timer
[    0.333544] NET: Registered protocol family 2
[    0.334430] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.334471] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    0.334510] TCP: Hash tables configured (established 1024 bind 1024)
[    0.334676] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.334725] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.334986] NET: Registered protocol family 1
[    0.335749] RPC: Registered named UNIX socket transport module.
[    0.335772] RPC: Registered udp transport module.
[    0.335787] RPC: Registered tcp transport module.
[    0.335802] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.336186] Unpacking initramfs...
[    1.045491] Freeing initrd memory: 6316K
[    1.046656] Initialise system trusted keyrings
[    1.046727] Key type blacklist registered
[    1.047009] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    1.054248] zbud: loaded
[    1.058672] NFS: Registering the id_resolver key type
[    1.058718] Key type id_resolver registered
[    1.058731] Key type id_legacy registered
[    1.058762] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.058775] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    1.059624] fuse init (API version 7.26)
[    1.060528] orangefs_debugfs_init: called with debug mask: :none: :0:
[    1.060797] orangefs_init: module version upstream loaded
[    3.044564] Key type asymmetric registered
[    3.044590] Asymmetric key parser 'x509' registered
[    3.044687] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    3.044705] io scheduler noop registered
[    3.044718] io scheduler deadline registered
[    3.044776] io scheduler cfq registered (default)
[    3.046960] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    3.048563] console [ttyS0] disabled
[    3.048696] 44200000.serial: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A
[    3.622927] console [ttyS0] enabled
[    3.637030] loop: module loaded
[    3.642032] scsi host0: sata_oxnas
[    3.645744] ata1: SATA max UDMA/133 irq 57
[    3.649991] sata_oxnas: resetting SATA core
[    3.717908] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[    3.724239] nand: Hynix H27U1G8F2BTR-BC
[    3.728107] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    3.735659] Scanning device for bad blocks
[    3.822223] 2 ofpart partitions found on MTD device 41000000.nand-controller
[    3.829276] Creating 2 MTD partitions on "41000000.nand-controller":
[    3.835609] 0x000000000000-0x000000e00000 : "boot"
[    3.841989] 0x000000e00000-0x000008000000 : "data"
[    3.849873] libphy: Fixed MDIO Bus: probed
[    3.854353] oxnas-dwmac 40400000.ethernet: PTP uses main clock
[    3.860239] oxnas-dwmac 40400000.ethernet: no reset control found
[    3.927774] stmmac - user ID: 0x12, Synopsys ID: 0x35
[    3.932812] oxnas-dwmac 40400000.ethernet: Ring mode enabled
[    3.938503] oxnas-dwmac 40400000.ethernet: DMA HW capability register supported
[    3.945779] oxnas-dwmac 40400000.ethernet: Enhanced/Alternate descriptors
[    3.952563] oxnas-dwmac 40400000.ethernet: Enabled extended descriptors
[    3.959170] oxnas-dwmac 40400000.ethernet: RX Checksum Offload Engine supported
[    3.966446] oxnas-dwmac 40400000.ethernet: COE Type 2
[    3.971499] oxnas-dwmac 40400000.ethernet: TX Checksum insertion supported
[    3.978375] oxnas-dwmac 40400000.ethernet: Wake-Up On Lan supported
[    3.984611] oxnas-dwmac 40400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    3.989588] ata1: SATA link down (SStatus 0 SControl 310)
[    4.046330] libphy: stmmac: probed
[    4.049794] mdio_bus stmmac-0:00: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[    4.059287] mdio_bus stmmac-0:07: attached PHY driver [unbound] (mii_bus:phy_addr=stmmac-0:07, irq=POLL)
[    4.069672] PPP generic driver version 2.4.2
[    4.074178] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.080750] ehci-pci: EHCI PCI platform driver
[    4.287736] oxnas-ehci 40200100.ehci: EHCI Host Controller
[    4.293248] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[    4.301140] oxnas-ehci 40200100.ehci: irq 52, io mem 0x40200100
[    4.327738] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[    4.334056] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    4.340874] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.348101] usb usb1: Product: EHCI Host Controller
[    4.352960] usb usb1: Manufacturer: Linux 4.14.180-oxnas-tld-1 ehci_hcd
[    4.359577] usb usb1: SerialNumber: 40200100.ehci
[    4.365056] hub 1-0:1.0: USB hub found
[    4.368954] hub 1-0:1.0: 2 ports detected
[    4.373918] usbcore: registered new interface driver cdc_wdm
[    4.379752] usbcore: registered new interface driver usb-storage
[    4.385863] usbcore: registered new interface driver usbserial
[    4.391815] usbcore: registered new interface driver usbserial_generic
[    4.398407] usbserial: USB Serial support registered for generic
[    4.404684] mousedev: PS/2 mouse device common for all mice
[    4.410434] i2c /dev entries driver
[    4.415144] hidraw: raw HID events driver (C) Jiri Kosina
[    4.420787] usbcore: registered new interface driver usbhid
[    4.426337] usbhid: USB HID core driver
[    4.431546] NET: Registered protocol family 10
[    4.437414] Segment Routing with IPv6
[    4.441236] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    4.448919] NET: Registered protocol family 17
[    4.453457] Key type dns_resolver registered
[    4.458941] registered taskstats version 1
[    4.463027] Loading compiled-in X.509 certificates
[    4.467955] zswap: loaded using pool lzo/zbud
[    4.549217] Key type big_key registered
[    4.589785] Key type encrypted registered
[    4.737697] usb 1-2: new high-speed USB device number 2 using oxnas-ehci

OX820> printenv
bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset
bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm 0x60500000 0x60e00000 0x62c00000; else bootm 0x60500000 0x60e00000; fi; else if run load_dtb; then bootm 0x60500000 - 0x62c00000; else bootm 0x60500000; fi; fi
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootdelay=10
bootdev=usb
device=0:1
devices=usb ide
disks=0 1 2 3
dtb_file=/boot/dts/ox820-pogoplug-pro.dtb
ethact=dwmac.40400000
ethaddr=52:3b:20:9c:11:51
if_netconsole=ping $serverip
ipaddr=192.168.0.222
load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device 0x62c00000 $dtb_file
load_initrd=echo loading uInitrd ...; load $bootdev $device 0x60e00000 /boot/uInitrd
load_uimage=echo loading uImage ...; load $bootdev $device 0x60500000 /boot/uImage
mainlineLinux=yes
mtdids=nand0=41000000.nand
mtdparts=mtdparts=41000000.nand:14m(boot),-(data)
preboot_nc=setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start";  setenv scan_ide "ide reset";  setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 0x60500000 /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done
serverip=192.168.0.220
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
uenv_import=echo importing envs ...; env import -t 0x60510000  $filesize
uenv_init_devices=setenv init_usb "usb start";  setenv init_ide "ide reset";  setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices;  do for disknum in 0; do run uenv_read_disk; done; done;
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x60500000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read;  fi; else if $devtype part $disknum; then run uenv_read; fi;  fi
usb_custom_params=zswap.enabled=1
usb_ready_retry=15

Environment size: 2720/131068 bytes
Re: oxnas(OX820)/Medion from openWRT to debian
May 18, 2023 06:07PM
> debain however still makes problems from usb with
> the new u-boot

dtb_file env was not set correctly.

Power up, interrupt serial console countdown, and
setenv dtb_file /boot/dts/ox820-stg212.dtb
boot

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Re: oxnas(OX820)/Medion from openWRT to debian
May 19, 2023 02:05AM
ok. i could have noticed that ;) Thanks now also runs Debian :)
Re: oxnas(OX820)/Medion from openWRT to debian
May 19, 2023 09:51AM
Most of it is done.
New U-Boot 2015 [check]
Debain running [check]
openWRT installed [check]

U-Boot now automatically loads openWRT (NAND) again.
I think by this input:
setenv bootcmd 'nboot 60500000 0 440000; bootm'
saveenv
How do I get the U-Boot to automatically boot from USB when a USB stick is inserted otherwise NAND?

I'm also thinking if it makes sense to install everything on HDD (sda1 rootfs,sda2 swap,sda3 data). Do you think this has an influence on the SAMBA speed?

Some kind of boot menu in U-Boot like GRUB would be good :)
Re: oxnas(OX820)/Medion from openWRT to debian
May 19, 2023 02:50PM
My workaround to come back to USB Boot:
setenv bootcmd run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset

but this start instant. How i can save it with saveenv?
Re: oxnas(OX820)/Medion from openWRT to debian
May 19, 2023 03:51PM
To dual boot Debian and OpenWrt.

setenv bootcmd_openwrt  'nboot 60500000 0 440000; bootm'
setenv bootcmd 'run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec;  run bootcmd_openwrt; reset'

After testing both ways of booting, save the envs

setenv bootcmd_openwrt  'nboot 60500000 0 440000; bootm'
setenv bootcmd 'run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec;  run bootcmd_openwrt; reset'
saveenv

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)



Edited 1 time(s). Last edit at 05/19/2023 09:03PM by bodhi.
Re: oxnas(OX820)/Medion from openWRT to debian
May 21, 2023 10:47AM
It works perfectly, thank you!!! :)

I tried to put the rootfs on the HDD. Unfortunately then the HDD idle does not work when swap and rootfs are on the disk. I think use the USB Stick for Rootfs/Swap in the future. :(

I tried to enable jumbo frames with
ifconfig eth0 down
ip link set eth0 mtu 9000 (6000,4000,2000)
ifconfig eth0 up
does not work. In the stock firmware from Medion the function was possible. Do you have a trick?

My next steps are tests because of the speed Samba/NFS/FTP.... Let's see what can be tickled out. I think the drive will be used for Proxmox backups in the future.



Edited 2 time(s). Last edit at 05/21/2023 10:48AM by snickerweb.
Re: oxnas(OX820)/Medion from openWRT to debian
May 21, 2023 01:54PM
snickerweb,

> I tried to put the rootfs on the HDD.
> Unfortunately then the HDD idle does not work when
> swap and rootfs are on the disk. I think use the
> USB Stick for Rootfs/Swap in the future. :(

Yes. Roofts cannot go to sleep. But swap file is OK. When the system is idle there is no swapping going on. So use the USB for rootfs, but create a 2nd swap file on the HDD, and use that. For example,

# cat /etc/fstab 
.....
/swapfile1     swap            swap    defaults          0       0

# cat /etc/rc.local
.....		
swapoff -v /swapfile1
swapon -v -p 2 /media/DATA/swapfile2

> My next steps are tests because of the speed
> Samba/NFS/FTP.... Let's see what can be tickled
> out. I think the drive will be used for Proxmox
> backups in the future.

See the Wiki thread for hints about performance tuning and benchmark.

I'm not sure if this OXNAS driver supports jumbo frames. Try reducing the speed. And make sure each node in your entire wire local network have jumbo frames. If even one node does not have jumbo frames, then the other nodes will not work in jumbo frames.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)



Edited 1 time(s). Last edit at 05/21/2023 02:37PM by bodhi.
Re: oxnas(OX820)/Medion from openWRT to debian
May 23, 2023 04:42AM
just a little hint, if you may run into some strange behavior... you've installed spl with 850MHz on NAND right now. Medion came with 750MHz by default. I noticed that commands like "agt-get update && apt-get upgrade" lead to segmentation fault when trying to create cache. With 800MHz it worked quite acceptable for me. Also our device doesn't have active cooling (no fan) and is already getting quite hot. I wouldn't recommend running 850MHz on regular basis.

next step i'm going to try is debian in openwrt chroot: https://openwrt.org/docs/guide-user/services/chroot



Edited 1 time(s). Last edit at 05/23/2023 04:46AM by alexinc.
Re: oxnas(OX820)/Medion from openWRT to debian
May 23, 2023 10:04AM
Thanxs alexinc,
how i can change the Mhz?
Re: oxnas(OX820)/Medion from openWRT to debian
May 23, 2023 02:26PM
See the entire discussion in this thread:
https://forum.doozan.com/read.php?4,54044


My suggestion:
https://forum.doozan.com/read.php?4,54044,135056#msg-135056

Quote
bodhi
With this type of problem, the best I can suggest is to stay with 4.14.198 for now if you run Debian.

Don't know when I will build Debian kernel 5.15.x, but that's my plan.The EOL date for 5.15.x is Oct 2026, and it might get extended.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Re: oxnas(OX820)/Medion from openWRT to debian
June 14, 2023 01:48PM
Hi bodhi,
I wanted to thank you again for the support. The system runs great so far.
Recently, after each reboot comes a disk check that takes a long time. Do you know why or how to turn it off?
see attachment
Attachments:
open | download - Screenshot 2023-06-14 204557.png (56.8 KB)
Re: oxnas(OX820)/Medion from openWRT to debian
June 14, 2023 03:05PM
snickerweb,

I need to see the entire serial consle log. Snippet of log is not enough to see what' going on.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Re: oxnas(OX820)/Medion from openWRT to debian
June 14, 2023 04:22PM
I found the problem. In fstab the last number from 1 to 0.
thanks a lot
Author:

Your Email:


Subject:


Spam prevention:
Please, enter the code that you see below in the input field. This is for blocking bots that try to post this form automatically. If the code is hard to read, then just try to guess it right. If you enter the wrong code, a new image is created and you get another chance to enter it right.
Message: