Goflex Net Cannot boot with USB

Hi all
I tried to install debian with the "Debian Wheezy installer" on a USB stick. After I finished it and tried
to reboot, I only will get acces to the Goflex over the rescue system. What could be the problem?
Thanks!

Netconsole output:
U-Boot 2011.12 (Apr 18 2012 - 23:08:20)
Seagate GoFlexNet
arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1
GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709
Hit any key to stop autoboot: 10 (Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/rescueme" from usb device 0:1 (usbda1)
** File not found /rescueme
reading /rescueme.txt

** Unable to read "/rescueme.txt" from usb 0:1 **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 219 MiB
UBI: number of good PEBs: 1752
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 1731
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1 bytes read
Found bootable drive on usb 0:1
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
64 bytes read
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
64 bytes read
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..

NAND read: device 0 offset 0x100000, size 0x400000
4194304 bytes read: OK
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-2.6.32.18-dockstar
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3236180 Bytes = 3.1 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

Hello

I've found this thread:



and I chroot the wheezy install as described.
Also I've changed the ip from DHCP to static as described here:



But I still have no access to the Goflex.
Has anyone an idea?

Thanks in advance!

Didi Wrote:
-------------------------------------------------------

> Loading file "/boot/uImage" from usb device 0:1
> (usbda1)
> 64 bytes read
> Loading file "/boot/uInitrd" from usb device 0:1
> (usbda1)
> 64 bytes read
> Wrong Image Format for bootm command
> ERROR: can't get kernel image!
> stopping USB..

Looks like your kernel images are not correct. You can rerun the same installation steps from the rescue system.

I rerun the installation but I still will get no acces to the box.
I get now the following result:

U-Boot 2011.12 (Apr 18 2012 - 23:08:20)
Seagate GoFlexNet
arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1
GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709
Hit any key to stop autoboot: 10 
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/rescueme" from usb device 0:1 (usbda1)
** File not found /rescueme
reading /rescueme.txt

** Unable to read "/rescueme.txt" from usb 0:1 **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 219 MiB
UBI: number of good PEBs: 1752
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 1731
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1 bytes read
Found bootable drive on usb 0:1
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1604552 bytes read
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
6756276 bytes read
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-3.2.0-4
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1604488 Bytes = 1.5 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-3.2.0-4-kirkwood
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 6756212 Bytes = 6.4 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

It looks good now!

Do you see the GFNet appears on the network at all? it could be assigned a different IP addr than before. Can you run nmap from a different computer? or look for it in the router web interface.

If you run nmap and see the GFNet does appear, then check to see if port 22 is opened.


Addendum:
I've just noticed this "Linux-3.2.0-4" in your boot log. It seems strange that it did not say "Linux-3.2.0-4-kirkwood". Can you post your installation log here?



Edited 1 time(s). Last edit at 11/18/2012 05:53PM by bodhi.

I don't see the GFNet in the network, the port 22 is open too.
Here is the bootstrap.log:

Connecting to cdn.debian.net (195.71.68.86:80)

debootstrap.invalid_ 0% | | 0 --:--:-- ETA
debootstrap.invalid_ 100% |*******************************| 210k --:--:-- ETA
Connecting to cdn.debian.net (195.71.68.86:80)

debootstrap.invalid_ 0% | | 0 --:--:-- ETA
debootstrap.invalid_ 23% |******* | 1331k 00:00:03 ETA
debootstrap.invalid_ 50% |*************** | 2865k 00:00:01 ETA
debootstrap.invalid_ 77% |*********************** | 4399k 00:00:00 ETA
debootstrap.invalid_ 100% |*******************************| 5652k 00:00:00 ETA
Connecting to cdn.debian.net (195.71.68.86:80)

libacl1_2.2.51-8_arm 0% | | 0 --:--:-- ETA
libacl1_2.2.51-8_arm 100% |*******************************| 27564 --:--:-- ETA
Connecting to cdn.debian.net (195.71.68.86:80)
...
...
...
zlib1g_1%3a1.2.7.dfs 0% | | 0 --:--:-- ETA
zlib1g_1%3a1.2.7.dfs 100% |*******************************| 87460 00:00:00 ETA
dpkg: warning: parsing file '/var/lib/dpkg/status' near line 5 package 'dpkg':
missing description
dpkg: warning: parsing file '/var/lib/dpkg/status' near line 5 package 'dpkg':
missing architecture
Selecting previously unselected package base-files.
dpkg: regarding .../base-files_6.11_armel.deb containing base-files, pre-dependency problem:
base-files pre-depends on awk
awk is not installed.

dpkg: warning: ignoring pre-dependency problem!
(Reading database ... 0 files and directories currently installed.)
Unpacking base-files (from .../base-files_6.11_armel.deb) ...
Selecting previously unselected package base-passwd.
Unpacking base-passwd (from .../base-passwd_3.5.26_armel.deb) ...
dpkg: base-passwd: dependency problems, but configuring anyway as you requested:
base-passwd depends on libc6 (>= 2.8); however:
Package libc6 is not installed.

Setting up base-passwd (3.5.26) ...
dpkg: base-files: dependency problems, but configuring anyway as you requested:
base-files depends on awk; however:
Package awk is not installed.

Setting up base-files (6.11) ...
dpkg: warning: parsing file '/var/lib/dpkg/status' near line 49 package 'dpkg':
missing description
dpkg: warning: parsing file '/var/lib/dpkg/status' near line 49 package 'dpkg':
missing architecture
dpkg: regarding .../archives/dpkg_1.16.9_armel.deb containing dpkg, pre-dependency problem:
dpkg pre-depends on libbz2-1.0
libbz2-1.0 is not installed.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../archives/dpkg_1.16.9_armel.deb containing dpkg, pre-dependency problem:
dpkg pre-depends on libc6 (>= 2.11)

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../archives/dpkg_1.16.9_armel.deb containing dpkg, pre-dependency problem:
dpkg pre-depends on libgcc1 (>= 1:4.4.0)

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../archives/dpkg_1.16.9_armel.deb containing dpkg, pre-dependency problem:
dpkg pre-depends on liblzma5 (>= 5.1.1alpha+20120614)

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../archives/dpkg_1.16.9_armel.deb containing dpkg, pre-dependency problem:
dpkg pre-depends on libselinux1 (>= 1.32)

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../archives/dpkg_1.16.9_armel.deb containing dpkg, pre-dependency problem:
dpkg pre-depends on zlib1g (>= 1:1.1.4)

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../archives/dpkg_1.16.9_armel.deb containing dpkg, pre-dependency problem:
dpkg pre-depends on tar (>= 1.23)

dpkg: warning: ignoring pre-dependency problem!
(Reading database ... 115 files and directories currently installed.)
Preparing to replace dpkg 1.16.9 (using .../archives/dpkg_1.16.9_armel.deb) ...
Unpacking replacement dpkg ...
dpkg: dpkg: dependency problems, but configuring anyway as you requested:
dpkg depends on libbz2-1.0; however:
Package libbz2-1.0 is not installed.
dpkg depends on libc6 (>= 2.11); however:
Package libc6 is not installed.
dpkg depends on libgcc1 (>= 1:4.4.0); however:
Package libgcc1 is not installed.
dpkg depends on liblzma5 (>= 5.1.1alpha+20120614); however:
Package liblzma5 is not installed.
dpkg depends on libselinux1 (>= 1.32); however:
Package libselinux1 is not installed.
dpkg depends on zlib1g (>= 1:1.1.4); however:
Package zlib1g is not installed.
dpkg depends on tar (>= 1.23); however:
Package tar is not installed.

Setting up dpkg (1.16.9) ...
Selecting previously unselected package libc6:armel.
(Reading database ... 371 files and directories currently installed.)
Unpacking libc6:armel (from .../libc6_2.13-35_armel.deb) ...
dpkg: libc6:armel: dependency problems, but configuring anyway as you requested:
libc6:armel depends on libc-bin (= 2.13-35); however:
Package libc-bin is not installed.
libc6:armel depends on libgcc1; however:
Package libgcc1 is not installed.

Setting up libc6:armel (2.13-35) ...
Selecting previously unselected package perl-base.
dpkg: regarding .../perl-base_5.14.2-15_armel.deb containing perl-base, pre-dependency problem:
perl-base pre-depends on libgcc1 (>= 1:4.4.0)

dpkg: warning: ignoring pre-dependency problem!
(Reading database ... 681 files and directories currently installed.)
Unpacking perl-base (from .../perl-base_5.14.2-15_armel.deb) ...
dpkg: perl-base: dependency problems, but configuring anyway as you requested:
perl-base depends on libgcc1 (>= 1:4.4.0); however:
Package libgcc1 is not installed.

Setting up perl-base (5.14.2-15) ...
Selecting previously unselected package mawk.
(Reading database ... 1751 files and directories currently installed.)
Unpacking mawk (from .../mawk_1.3.3-17_armel.deb) ...
Setting up mawk (1.3.3-17) ...
Selecting previously unselected package libacl1:armel.
dpkg: regarding .../libacl1_2.2.51-8_armel.deb containing libacl1:armel, pre-dependency problem:
libacl1 pre-depends on multiarch-support
multiarch-support is not installed.

dpkg: warning: ignoring pre-dependency problem!
(Reading database ... 1770 files and directories currently installed.)
Unpacking libacl1:armel (from .../libacl1_2.2.51-8_armel.deb) ...
Selecting previously unselected package libattr1:armel.
dpkg: regarding .../libattr1_1%3a2.4.46-8_armel.deb containing libattr1:armel, pre-dependency problem:
libattr1 pre-depends on multiarch-support
multiarch-support is not installed.

dpkg: warning: ignoring pre-dependency problem!
Unpacking libattr1:armel (from .../libattr1_1%3a2.4.46-8_armel.deb) ...
Preparing to replace base-files 6.11 (using .../base-files_6.11_armel.deb) ...
Unpacking replacement base-files ...
Preparing to replace base-passwd 3.5.26 (using .../base-passwd_3.5.26_armel.deb) ...
Unpacking replacement base-passwd ...
Selecting previously unselected package bash.
dpkg: regarding .../archives/bash_4.2-4_armel.deb containing bash, pre-dependency problem:
bash pre-depends on dash (>= 0.5.5.1-2.2)

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../archives/bash_4.2-4_armel.deb containing bash, pre-dependency problem:
bash pre-depends on libgcc1 (>= 1:4.4.0)

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../archives/bash_4.2-4_armel.deb containing bash, pre-dependency problem:
bash pre-depends on libtinfo5
libtinfo5 is not installed.

dpkg: warning: ignoring pre-dependency problem!
Unpacking bash (from .../archives/bash_4.2-4_armel.deb) ...
Selecting previously unselected package libbz2-1.0:armel.
dpkg: regarding .../libbz2-1.0_1.0.6-4_armel.deb containing libbz2-1.0:armel, pre-dependency problem:
libbz2-1.0 pre-depends on multiarch-support
multiarch-support is not installed.

dpkg: warning: ignoring pre-dependency problem!
Unpacking libbz2-1.0:armel (from .../libbz2-1.0_1.0.6-4_armel.deb) ...
Selecting previously unselected package coreutils.
dpkg: regarding .../coreutils_8.13-3.2_armel.deb containing coreutils, pre-dependency problem:
coreutils pre-depends on libacl1 (>= 2.2.51-5)
libacl1:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../coreutils_8.13-3.2_armel.deb containing coreutils, pre-dependency problem:
coreutils pre-depends on libattr1 (>= 1:2.4.46-5)
libattr1:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../coreutils_8.13-3.2_armel.deb containing coreutils, pre-dependency problem:
coreutils pre-depends on libgcc1 (>= 1:4.4.0)

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../coreutils_8.13-3.2_armel.deb containing coreutils, pre-dependency problem:
coreutils pre-depends on libselinux1 (>= 1.32)

dpkg: warning: ignoring pre-dependency problem!
Unpacking coreutils (from .../coreutils_8.13-3.2_armel.deb) ...
Selecting previously unselected package dash.
Unpacking dash (from .../dash_0.5.7-3_armel.deb) ...
Adding 'diversion of /bin/sh to /bin/sh.distrib by dash'
Adding 'diversion of /usr/share/man/man1/sh.1.gz to /usr/share/man/man1/sh.distrib.1.gz by dash'
Selecting previously unselected package libdb5.1:armel.
dpkg: regarding .../libdb5.1_5.1.29-5_armel.deb containing libdb5.1:armel, pre-dependency problem:
libdb5.1 pre-depends on multiarch-support
multiarch-support is not installed.

dpkg: warning: ignoring pre-dependency problem!
Unpacking libdb5.1:armel (from .../libdb5.1_5.1.29-5_armel.deb) ...
Selecting previously unselected package debconf.
Unpacking debconf (from .../debconf_1.5.46_all.deb) ...
Selecting previously unselected package debconf-i18n.
Unpacking debconf-i18n (from .../debconf-i18n_1.5.46_all.deb) ...
Selecting previously unselected package debianutils.
Unpacking debianutils (from .../debianutils_4.3.2_armel.deb) ...
Selecting previously unselected package diffutils.
dpkg: regarding .../diffutils_1%3a3.2-6_armel.deb containing diffutils, pre-dependency problem:
diffutils pre-depends on libgcc1 (>= 1:4.4.0)

dpkg: warning: ignoring pre-dependency problem!
Unpacking diffutils (from .../diffutils_1%3a3.2-6_armel.deb) ...
dpkg: regarding .../archives/dpkg_1.16.9_armel.deb containing dpkg, pre-dependency problem:
dpkg pre-depends on libbz2-1.0
libbz2-1.0:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../archives/dpkg_1.16.9_armel.deb containing dpkg, pre-dependency problem:
dpkg pre-depends on libgcc1 (>= 1:4.4.0)

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../archives/dpkg_1.16.9_armel.deb containing dpkg, pre-dependency problem:
dpkg pre-depends on liblzma5 (>= 5.1.1alpha+20120614)

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../archives/dpkg_1.16.9_armel.deb containing dpkg, pre-dependency problem:
dpkg pre-depends on libselinux1 (>= 1.32)

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../archives/dpkg_1.16.9_armel.deb containing dpkg, pre-dependency problem:
dpkg pre-depends on zlib1g (>= 1:1.1.4)

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../archives/dpkg_1.16.9_armel.deb containing dpkg, pre-dependency problem:
dpkg pre-depends on tar (>= 1.23)

dpkg: warning: ignoring pre-dependency problem!
Preparing to replace dpkg 1.16.9 (using .../archives/dpkg_1.16.9_armel.deb) ...
Unpacking replacement dpkg ...
Selecting previously unselected package e2fslibs:armel.
dpkg: regarding .../e2fslibs_1.42.5-1_armel.deb containing e2fslibs:armel, pre-dependency problem:
e2fslibs pre-depends on multiarch-support
multiarch-support is not installed.

dpkg: warning: ignoring pre-dependency problem!
Unpacking e2fslibs:armel (from .../e2fslibs_1.42.5-1_armel.deb) ...
Selecting previously unselected package e2fsprogs.
dpkg: regarding .../e2fsprogs_1.42.5-1_armel.deb containing e2fsprogs, pre-dependency problem:
e2fsprogs pre-depends on e2fslibs (= 1.42.5-1)
e2fslibs:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../e2fsprogs_1.42.5-1_armel.deb containing e2fsprogs, pre-dependency problem:
e2fsprogs pre-depends on libblkid1 (>= 2.17.2)

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../e2fsprogs_1.42.5-1_armel.deb containing e2fsprogs, pre-dependency problem:
e2fsprogs pre-depends on libcomerr2 (>= 1.42~WIP-2011-10-05-1)

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../e2fsprogs_1.42.5-1_armel.deb containing e2fsprogs, pre-dependency problem:
e2fsprogs pre-depends on libgcc1 (>= 1:4.4.0)

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../e2fsprogs_1.42.5-1_armel.deb containing e2fsprogs, pre-dependency problem:
e2fsprogs pre-depends on libss2 (>= 1.34-1)

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../e2fsprogs_1.42.5-1_armel.deb containing e2fsprogs, pre-dependency problem:
e2fsprogs pre-depends on libuuid1 (>= 2.16)

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../e2fsprogs_1.42.5-1_armel.deb containing e2fsprogs, pre-dependency problem:
e2fsprogs pre-depends on util-linux (>= 2.15~rc1-1)

dpkg: warning: ignoring pre-dependency problem!
Unpacking e2fsprogs (from .../e2fsprogs_1.42.5-1_armel.deb) ...
Selecting previously unselected package libcomerr2:armel.
dpkg: regarding .../libcomerr2_1.42.5-1_armel.deb containing libcomerr2:armel, pre-dependency problem:
libcomerr2 pre-depends on multiarch-support
multiarch-support is not installed.

dpkg: warning: ignoring pre-dependency problem!
Unpacking libcomerr2:armel (from .../libcomerr2_1.42.5-1_armel.deb) ...
Selecting previously unselected package libss2:armel.
dpkg: regarding .../libss2_1.42.5-1_armel.deb containing libss2:armel, pre-dependency problem:
libss2 pre-depends on multiarch-support
multiarch-support is not installed.

dpkg: warning: ignoring pre-dependency problem!
Unpacking libss2:armel (from .../libss2_1.42.5-1_armel.deb) ...
Selecting previously unselected package libc-bin.
Unpacking libc-bin (from .../libc-bin_2.13-35_armel.deb) ...
Preparing to replace libc6:armel 2.13-35 (using .../libc6_2.13-35_armel.deb) ...
Unpacking replacement libc6:armel ...
Selecting previously unselected package multiarch-support.
Unpacking multiarch-support (from .../multiarch-support_2.13-35_armel.deb) ...
Selecting previously unselected package findutils.
dpkg: regarding .../findutils_4.4.2-4_armel.deb containing findutils, pre-dependency problem:
findutils pre-depends on libgcc1 (>= 1:4.4.0)

dpkg: warning: ignoring pre-dependency problem!
Unpacking findutils (from .../findutils_4.4.2-4_armel.deb) ...
Selecting previously unselected package gcc-4.7-base:armel.
Unpacking gcc-4.7-base:armel (from .../gcc-4.7-base_4.7.2-4_armel.deb) ...
Selecting previously unselected package libgcc1:armel.
dpkg: regarding .../libgcc1_1%3a4.7.2-4_armel.deb containing libgcc1:armel, pre-dependency problem:
libgcc1 pre-depends on multiarch-support
multiarch-support is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
Unpacking libgcc1:armel (from .../libgcc1_1%3a4.7.2-4_armel.deb) ...
Selecting previously unselected package grep.
dpkg: regarding .../archives/grep_2.12-2_armel.deb containing grep, pre-dependency problem:
grep pre-depends on libgcc1 (>= 1:4.4.0)
libgcc1:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
Unpacking grep (from .../archives/grep_2.12-2_armel.deb) ...
Selecting previously unselected package gzip.
dpkg: regarding .../gzip_1.5-1.1_armel.deb containing gzip, pre-dependency problem:
gzip pre-depends on libgcc1 (>= 1:4.4.0)
libgcc1:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
Unpacking gzip (from .../gzip_1.5-1.1_armel.deb) ...
Selecting previously unselected package hostname.
Unpacking hostname (from .../hostname_3.11_armel.deb) ...
Selecting previously unselected package insserv.
Unpacking insserv (from .../insserv_1.14.0-4_armel.deb) ...
Selecting previously unselected package liblocale-gettext-perl.
Unpacking liblocale-gettext-perl (from .../liblocale-gettext-perl_1.05-7+b1_armel.deb) ...
Selecting previously unselected package libselinux1:armel.
dpkg: regarding .../libselinux1_2.1.9-5_armel.deb containing libselinux1:armel, pre-dependency problem:
libselinux1 pre-depends on multiarch-support
multiarch-support is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
Unpacking libselinux1:armel (from .../libselinux1_2.1.9-5_armel.deb) ...
Selecting previously unselected package libsemanage-common.
Unpacking libsemanage-common (from .../libsemanage-common_2.1.6-6_all.deb) ...
Selecting previously unselected package libsemanage1:armel.
dpkg: regarding .../libsemanage1_2.1.6-6_armel.deb containing libsemanage1:armel, pre-dependency problem:
libsemanage1 pre-depends on multiarch-support
multiarch-support is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
Unpacking libsemanage1:armel (from .../libsemanage1_2.1.6-6_armel.deb) ...
Selecting previously unselected package libsepol1:armel.
dpkg: regarding .../libsepol1_2.1.4-3_armel.deb containing libsepol1:armel, pre-dependency problem:
libsepol1 pre-depends on multiarch-support
multiarch-support is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
Unpacking libsepol1:armel (from .../libsepol1_2.1.4-3_armel.deb) ...
Selecting previously unselected package libtext-charwidth-perl.
Unpacking libtext-charwidth-perl (from .../libtext-charwidth-perl_0.04-7+b1_armel.deb) ...
Selecting previously unselected package libtext-iconv-perl.
Unpacking libtext-iconv-perl (from .../libtext-iconv-perl_1.7-5_armel.deb) ...
Selecting previously unselected package libtext-wrapi18n-perl.
Unpacking libtext-wrapi18n-perl (from .../libtext-wrapi18n-perl_0.06-7_all.deb) ...
Selecting previously unselected package lsb-base.
Unpacking lsb-base (from .../lsb-base_4.1+Debian8_all.deb) ...
Preparing to replace mawk 1.3.3-17 (using .../mawk_1.3.3-17_armel.deb) ...
Unpacking replacement mawk ...
Selecting previously unselected package libncurses5:armel.
dpkg: regarding .../libncurses5_5.9-10_armel.deb containing libncurses5:armel, pre-dependency problem:
libncurses5 pre-depends on multiarch-support
multiarch-support is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../libncurses5_5.9-10_armel.deb containing libncurses5:armel, pre-dependency problem:
libncurses5 pre-depends on libtinfo5 (>= 5.9-3)

dpkg: warning: ignoring pre-dependency problem!
Unpacking libncurses5:armel (from .../libncurses5_5.9-10_armel.deb) ...
Selecting previously unselected package libtinfo5:armel.
dpkg: regarding .../libtinfo5_5.9-10_armel.deb containing libtinfo5:armel, pre-dependency problem:
libtinfo5 pre-depends on multiarch-support
multiarch-support is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
Unpacking libtinfo5:armel (from .../libtinfo5_5.9-10_armel.deb) ...
Selecting previously unselected package ncurses-base.
Unpacking ncurses-base (from .../ncurses-base_5.9-10_all.deb) ...
Selecting previously unselected package ncurses-bin.
dpkg: regarding .../ncurses-bin_5.9-10_armel.deb containing ncurses-bin, pre-dependency problem:
ncurses-bin pre-depends on libtinfo5 (>= 5.9-3~)
libtinfo5:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
Unpacking ncurses-bin (from .../ncurses-bin_5.9-10_armel.deb) ...
Selecting previously unselected package libpam-modules:armel.
dpkg: regarding .../libpam-modules_1.1.3-7.1_armel.deb containing libpam-modules:armel, pre-dependency problem:
libpam-modules pre-depends on libdb5.1
libdb5.1:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../libpam-modules_1.1.3-7.1_armel.deb containing libpam-modules:armel, pre-dependency problem:
libpam-modules pre-depends on libpam0g (>= 1.1.3-2)

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../libpam-modules_1.1.3-7.1_armel.deb containing libpam-modules:armel, pre-dependency problem:
libpam-modules pre-depends on libselinux1 (>= 2.0.85)
libselinux1:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../libpam-modules_1.1.3-7.1_armel.deb containing libpam-modules:armel, pre-dependency problem:
libpam-modules pre-depends on debconf (>= 0.5) | debconf-2.0
debconf is unpacked, but has never been configured.
debconf provides debconf-2.0 but is unpacked but not configured.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../libpam-modules_1.1.3-7.1_armel.deb containing libpam-modules:armel, pre-dependency problem:
libpam-modules pre-depends on libpam-modules-bin (= 1.1.3-7.1)

dpkg: warning: ignoring pre-dependency problem!
Unpacking libpam-modules:armel (from .../libpam-modules_1.1.3-7.1_armel.deb) ...
Selecting previously unselected package libpam-modules-bin.
Unpacking libpam-modules-bin (from .../libpam-modules-bin_1.1.3-7.1_armel.deb) ...
Selecting previously unselected package libpam-runtime.
Unpacking libpam-runtime (from .../libpam-runtime_1.1.3-7.1_all.deb) ...
Selecting previously unselected package libpam0g:armel.
dpkg: regarding .../libpam0g_1.1.3-7.1_armel.deb containing libpam0g:armel, pre-dependency problem:
libpam0g pre-depends on multiarch-support
multiarch-support is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
Unpacking libpam0g:armel (from .../libpam0g_1.1.3-7.1_armel.deb) ...
Selecting previously unselected package login.
dpkg: regarding .../login_1%3a4.1.5.1-1_armel.deb containing login, pre-dependency problem:
login pre-depends on libgcc1 (>= 1:4.4.0)
libgcc1:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../login_1%3a4.1.5.1-1_armel.deb containing login, pre-dependency problem:
login pre-depends on libpam0g (>= 0.99.7.1)
libpam0g:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../login_1%3a4.1.5.1-1_armel.deb containing login, pre-dependency problem:
login pre-depends on libpam-runtime
libpam-runtime is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../login_1%3a4.1.5.1-1_armel.deb containing login, pre-dependency problem:
login pre-depends on libpam-modules
libpam-modules:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
Unpacking login (from .../login_1%3a4.1.5.1-1_armel.deb) ...
Selecting previously unselected package libslang2:armel.
dpkg: regarding .../libslang2_2.2.4-15_armel.deb containing libslang2:armel, pre-dependency problem:
libslang2 pre-depends on multiarch-support
multiarch-support is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
Unpacking libslang2:armel (from .../libslang2_2.2.4-15_armel.deb) ...
Selecting previously unselected package initscripts.
Unpacking initscripts (from .../initscripts_2.88dsf-32_armel.deb) ...
Selecting previously unselected package libustr-1.0-1:armel.
dpkg: regarding .../libustr-1.0-1_1.0.4-3_armel.deb containing libustr-1.0-1:armel, pre-dependency problem:
libustr-1.0-1 pre-depends on multiarch-support
multiarch-support is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
Unpacking libustr-1.0-1:armel (from .../libustr-1.0-1_1.0.4-3_armel.deb) ...
Selecting previously unselected package bsdutils.
Unpacking bsdutils (from .../bsdutils_1%3a2.20.1-5.2_armel.deb) ...
Selecting previously unselected package libblkid1:armel.
dpkg: regarding .../libblkid1_2.20.1-5.2_armel.deb containing libblkid1:armel, pre-dependency problem:
libblkid1 pre-depends on multiarch-support
multiarch-support is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
Unpacking libblkid1:armel (from .../libblkid1_2.20.1-5.2_armel.deb) ...
Selecting previously unselected package libmount1.
dpkg: regarding .../libmount1_2.20.1-5.2_armel.deb containing libmount1, pre-dependency problem:
libmount1 pre-depends on multiarch-support
multiarch-support is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
Unpacking libmount1 (from .../libmount1_2.20.1-5.2_armel.deb) ...
Selecting previously unselected package libuuid1:armel.
dpkg: regarding .../libuuid1_2.20.1-5.2_armel.deb containing libuuid1:armel, pre-dependency problem:
libuuid1 pre-depends on multiarch-support
multiarch-support is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
Unpacking libuuid1:armel (from .../libuuid1_2.20.1-5.2_armel.deb) ...
Selecting previously unselected package mount.
dpkg: regarding .../mount_2.20.1-5.2_armel.deb containing mount, pre-dependency problem:
mount pre-depends on libblkid1 (>= 2.20.1)
libblkid1:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../mount_2.20.1-5.2_armel.deb containing mount, pre-dependency problem:
mount pre-depends on libgcc1 (>= 1:4.4.0)
libgcc1:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../mount_2.20.1-5.2_armel.deb containing mount, pre-dependency problem:
mount pre-depends on libmount1 (>= 2.20.1)
libmount1 is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../mount_2.20.1-5.2_armel.deb containing mount, pre-dependency problem:
mount pre-depends on libselinux1 (>= 2.0.15)
libselinux1:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../mount_2.20.1-5.2_armel.deb containing mount, pre-dependency problem:
mount pre-depends on libsepol1 (>= 1.14)
libsepol1:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
Unpacking mount (from .../mount_2.20.1-5.2_armel.deb) ...
Selecting previously unselected package liblzma5:armel.
dpkg: regarding .../liblzma5_5.1.1alpha+20120614-1_armel.deb containing liblzma5:armel, pre-dependency problem:
liblzma5 pre-depends on multiarch-support
multiarch-support is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
Unpacking liblzma5:armel (from .../liblzma5_5.1.1alpha+20120614-1_armel.deb) ...
dpkg: regarding .../perl-base_5.14.2-15_armel.deb containing perl-base, pre-dependency problem:
perl-base pre-depends on libgcc1 (>= 1:4.4.0)
libgcc1:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
Preparing to replace perl-base 5.14.2-15 (using .../perl-base_5.14.2-15_armel.deb) ...
Unpacking replacement perl-base ...
Selecting previously unselected package sed.
dpkg: regarding .../sed_4.2.1-10_armel.deb containing sed, pre-dependency problem:
sed pre-depends on libselinux1 (>= 1.32)
libselinux1:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
Unpacking sed (from .../sed_4.2.1-10_armel.deb) ...
Selecting previously unselected package sensible-utils.
Unpacking sensible-utils (from .../sensible-utils_0.0.7_all.deb) ...
Selecting previously unselected package passwd.
Unpacking passwd (from .../passwd_1%3a4.1.5.1-1_armel.deb) ...
Selecting previously unselected package sysv-rc.
Unpacking sysv-rc (from .../sysv-rc_2.88dsf-32_all.deb) ...
Selecting previously unselected package sysvinit.
dpkg: regarding .../sysvinit_2.88dsf-32_armel.deb containing sysvinit, pre-dependency problem:
sysvinit pre-depends on initscripts (>= 2.88dsf-13.3)
initscripts is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../sysvinit_2.88dsf-32_armel.deb containing sysvinit, pre-dependency problem:
sysvinit pre-depends on sysv-rc | file-rc
sysv-rc is unpacked, but has never been configured.
file-rc is not installed.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../sysvinit_2.88dsf-32_armel.deb containing sysvinit, pre-dependency problem:
sysvinit pre-depends on sysvinit-utils (>= 2.86.ds1-66)

dpkg: warning: ignoring pre-dependency problem!
Unpacking sysvinit (from .../sysvinit_2.88dsf-32_armel.deb) ...
Selecting previously unselected package sysvinit-utils.
Unpacking sysvinit-utils (from .../sysvinit-utils_2.88dsf-32_armel.deb) ...
Selecting previously unselected package tar.
dpkg: regarding .../archives/tar_1.26-4_armel.deb containing tar, pre-dependency problem:
tar pre-depends on libgcc1 (>= 1:4.4.0)
libgcc1:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
Unpacking tar (from .../archives/tar_1.26-4_armel.deb) ...
Selecting previously unselected package tzdata.
Unpacking tzdata (from .../tzdata_2012g-1_all.deb) ...
Selecting previously unselected package util-linux.
dpkg: regarding .../util-linux_2.20.1-5.2_armel.deb containing util-linux, pre-dependency problem:
util-linux pre-depends on libblkid1 (>= 2.20.1)
libblkid1:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../util-linux_2.20.1-5.2_armel.deb containing util-linux, pre-dependency problem:
util-linux pre-depends on libgcc1 (>= 1:4.4.0)
libgcc1:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../util-linux_2.20.1-5.2_armel.deb containing util-linux, pre-dependency problem:
util-linux pre-depends on libncurses5 (>= 5.5-5~)
libncurses5:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../util-linux_2.20.1-5.2_armel.deb containing util-linux, pre-dependency problem:
util-linux pre-depends on libselinux1 (>= 1.32)
libselinux1:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../util-linux_2.20.1-5.2_armel.deb containing util-linux, pre-dependency problem:
util-linux pre-depends on libslang2 (>= 2.2.4)
libslang2:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../util-linux_2.20.1-5.2_armel.deb containing util-linux, pre-dependency problem:
util-linux pre-depends on libtinfo5
libtinfo5:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../util-linux_2.20.1-5.2_armel.deb containing util-linux, pre-dependency problem:
util-linux pre-depends on libuuid1 (>= 2.16)
libuuid1:armel is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
dpkg: regarding .../util-linux_2.20.1-5.2_armel.deb containing util-linux, pre-dependency problem:
util-linux pre-depends on zlib1g (>= 1:1.1.4)

dpkg: warning: ignoring pre-dependency problem!
Unpacking util-linux (from .../util-linux_2.20.1-5.2_armel.deb) ...
Selecting previously unselected package xz-utils.
Unpacking xz-utils (from .../xz-utils_5.1.1alpha+20120614-1_armel.deb) ...
Selecting previously unselected package zlib1g:armel.
dpkg: regarding .../zlib1g_1%3a1.2.7.dfsg-13_armel.deb containing zlib1g:armel, pre-dependency problem:
zlib1g pre-depends on multiarch-support
multiarch-support is unpacked, but has never been configured.

dpkg: warning: ignoring pre-dependency problem!
Unpacking zlib1g:armel (from .../zlib1g_1%3a1.2.7.dfsg-13_armel.deb) ...
Setting up lsb-base (4.1+Debian8) ...
...
...
...
Setting up tzdata (2012g-1) ...

Current default time zone: 'Etc/UTC'
Local time is now: Thu Jan 1 00:57:27 UTC 1970.
Universal Time is now: Thu Jan 1 00:57:27 UTC 1970.
Run 'dpkg-reconfigure tzdata' if you wish to change it.

Setting up debconf-i18n (1.5.46) ...
Setting up initscripts (2.88dsf-32) ...
guest environment detected: Linking /dev/shm to /run/shm
invoke-rc.d: unknown initscript, /etc/init.d/urandom.sh not found.
Setting up libpam-modules-bin (1.1.3-7.1) ...
Setting up libpam-modules:armel (1.1.3-7.1) ...
Setting up passwd (1:4.1.5.1-1) ...
Shadow passwords are now on.
Setting up libpam-runtime (1.1.3-7.1) ...
Setting up sysvinit (2.88dsf-32) ...
sysvinit: creating /run/initctl
Not restarting sysvinit: chroot detected
Setting up login (1:4.1.5.1-1) ...
Setting up libuuid1:armel (2.20.1-5.2) ...
Setting up libblkid1:armel (2.20.1-5.2) ...
Setting up util-linux (2.20.1-5.2) ...
update-alternatives: using /bin/more to provide /usr/bin/pager (pager) in auto mode
Setting up libmount1 (2.20.1-5.2) ...
Setting up mount (2.20.1-5.2) ...
Setting up e2fsprogs (1.42.5-1) ...
(Reading database ... 6256 files and directories currently installed.)
Unpacking adduser (from .../adduser_3.113+nmu3_all.deb) ...
...
...
...
Setting up udev (175-7) ...
A chroot environment has been detected, udev not started.
Setting up libkrb5-3:armel (1.10.1+dfsg-2) ...
Setting up initramfs-tools (0.109) ...
update-initramfs: deferring update (trigger activated)
Setting up module-init-tools (9-2) ...
Setting up libgssapi-krb5-2:armel (1.10.1+dfsg-2) ...
Setting up apt (0.9.7.6) ...
gpg: keyring `/etc/apt/trusted.gpg' created
gpg: key B98321F9 was created 1281135048 seconds in the future (time warp or clock problem)
gpg: key B98321F9 was created 1281135048 seconds in the future (time warp or clock problem)
gpg: key B98321F9 was created 1281135048 seconds in the future (time warp or clock problem)
gpg: key B98321F9: "Squeeze Stable Release Key <debian-release@lists.debian.org>" not changed
gpg: key 473041FA was created 1282935210 seconds in the future (time warp or clock problem)
gpg: key 473041FA was created 1282935210 seconds in the future (time warp or clock problem)
gpg: key 473041FA was created 1282935210 seconds in the future (time warp or clock problem)
gpg: key 473041FA: "Debian Archive Automatic Signing Key (6.0/squeeze) <ftpmaster@debian.org>" not changed
gpg: key 65FFB764 was created 1336484496 seconds in the future (time warp or clock problem)
gpg: key 65FFB764 was created 1336484496 seconds in the future (time warp or clock problem)
gpg: key 65FFB764 was created 1336484496 seconds in the future (time warp or clock problem)
gpg: key 65FFB764: "Wheezy Stable Release Key <debian-release@lists.debian.org>" not changed
gpg: key 46925553 was created 1335548304 seconds in the future (time warp or clock problem)
gpg: key 46925553 was created 1335548304 seconds in the future (time warp or clock problem)
gpg: key 46925553 was created 1335548304 seconds in the future (time warp or clock problem)
gpg: key 46925553: "Debian Archive Automatic Signing Key (7.0/wheezy) <ftpmaster@debian.org>" not changed
gpg: Total number processed: 4
gpg: unchanged: 4
gpg: /etc/apt//trustdb.gpg: trustdb created
gpg: key 1DB114E0 was created 1074188077 seconds in the future (time warp or clock problem)
...
...
...
gpg: key B98321F9 was created 1281135048 seconds in the future (time warp or clock problem)
gpg: key 46925553 was created 1335548304 seconds in the future (time warp or clock problem)
gpg: key 65FFB764 was created 1336484496 seconds in the future (time warp or clock problem)
Setting up flash-kernel (3.3) ...
Setting up wget (1.13.4-3) ...
Setting up linux-image-3.2.0-4-kirkwood (3.2.32-1) ...
Running depmod.
Examining /etc/kernel/postinst.d.
run-parts: executing /etc/kernel/postinst.d/initramfs-tools 3.2.0-4-kirkwood /boot/vmlinuz-3.2.0-4-kirkwood
update-initramfs: Generating /boot/initrd.img-3.2.0-4-kirkwood
Warning: root device does not exist

Unable to abort; system will probably be broken!
flash-kernel: deferring update (trigger activated)
run-parts: executing /etc/kernel/postinst.d/zz-flash-kernel 3.2.0-4-kirkwood /boot/vmlinuz-3.2.0-4-kirkwood
flash-kernel: deferring update (trigger activated)
Setting up openssh-client (1:6.0p1-3) ...
Setting up openssh-server (1:6.0p1-3) ...
Creating SSH2 RSA key; this may take some time ...
Creating SSH2 DSA key; this may take some time ...
Creating SSH2 ECDSA key; this may take some time ...
Restarting OpenBSD Secure Shell server: sshd
Warning: Fake start-stop-daemon called, doing nothing

Warning: Fake start-stop-daemon called, doing nothing
.
Setting up linux-image-kirkwood (3.2+46) ...
Processing triggers for initramfs-tools ...
update-initramfs: Generating /boot/initrd.img-3.2.0-4-kirkwood
Warning: root device does not exist

Unable to abort; system will probably be broken!
flash-kernel: installing version 3.2.0-4-kirkwood
Generating kernel u-boot image... done.
Installing new uImage.
Generating initramfs u-boot image... done.
Installing new uInitrd.
Processing triggers for flash-kernel ...
flash-kernel: installing version 3.2.0-4-kirkwood
Generating kernel u-boot image... done.
Taking backup of uImage.
Installing new uImage.
Generating initramfs u-boot image... done.
Taking backup of uInitrd.
Installing new uInitrd.

I've tried to install the wheezy script several times. It seem that everything goes well, but I still will get no IP address.
Are there some more things I can try?


NC:
U-Boot 2011.12 (Apr 18 2012 - 23:08:20)
Seagate GoFlexNet
arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1
GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709
Hit any key to stop autoboot: 10  9  8  7  6  5  4  3  2  1  0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/rescueme" from usb device 0:1 (usbda1)
** File not found /rescueme
reading /rescueme.txt

** Unable to read "/rescueme.txt" from usb 0:1 **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 219 MiB
UBI: number of good PEBs: 1752
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 1731
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1 bytes read
Found bootable drive on usb 0:1
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1604552 bytes read
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
6756616 bytes read
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-3.2.0-4
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1604488 Bytes = 1.5 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-3.2.0-4-kirkwood
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 6756552 Bytes = 6.4 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

You might try:

1. mount the USB stick on another Linux box and run fsck to check for error and fix it if there were, and reboot. If still no IP, try:

2. Stop the boot process in netconsole during the countdown and then set the env usb_custom_params to enable netconsole output when the kernel starts. See this post for example:

http://forum.doozan.com/read.php?2,7676,9963#msg-9963

Hi bodhi

Thank you for your helping!
I've solved the problem now. The uboot was not all right.
I fixed it and now everything is working.

cd /tmp
wget http://projects.doozan.com/uboot/install_uboot_mtd0.sh
chmod +x install_uboot_mtd0.sh
./install_uboot_mtd0.sh --no-uboot-check

Didi