Pogoplug E02: Squeeze install not booting multiple USB September 13, 2013 09:40AM |
Registered: 10 years ago Posts: 6 |
ethact=egiga0 bootdelay=3 baudrate=115200 mainlineLinux=yes console=ttyS0,115200 led_init=green blinking led_exit=green off led_error=orange blinking mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) mtdids=nand0=orion_nand partition=nand0,2 stdin=serial stdout=serial stderr=serial rescue_installed=0 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done usb_scan_list=1 2 3 4 usb_scan_1=usb=0:1 dev=sda1 usb_scan_2=usb=1:1 dev=sdb1 usb_scan_3=usb=2:1 dev=sdc1 usb_scan_4=usb=3:1 dev=sdd1 usb_init=run usb_scan usb_device=0:1 usb_root=/dev/sda1 usb_rootfstype=ext2 usb_rootdelay=10 usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset ethaddr=00:25:31:00:B4:85 arcNumber=2097
U-Boot 2011.12 (Feb 20 2012 - 21:21:59) Pogoplug E02 arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1 GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709 Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Loading file "/rescueme" from usb device 0:1 (usbda1) ** File not found /rescueme reading /rescueme.txt ** Unable to read "/rescueme.txt" from usb 0:1 ** Creating 1 MTD partitions on "nand0": 0x000002500000-0x000008000000 : "mtd=3" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=3" UBI: MTD device size: 91 MiB UBI: number of good PEBs: 726 UBI: number of bad PEBs: 2 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 0 UBI: available PEBs: 715 UBI: total number of reserved PEBs: 11 UBI: number of PEBs reserved for bad PEB handling: 7 UBI: max/mean erase counter: 1/1 UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19 Error reading superblock on volume 'ubi:rootfs'! Loading file "/boot/uImage" from usb device 0:1 (usbda1) ** File not found /boot/uImage ** Block device usb 1 not supported ** Block device usb 2 not supported ** Block device usb 3 not supported Loading file "/boot/uImage" from usb device 0:1 (usbda1) ** File not found /boot/uImage Loading file "/boot/uInitrd" from usb device 0:1 (usbda1) ** File not found /boot/uInitrd Wrong Image Format for bootm command ERROR: can't get kernel image! stopping USB.. ### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000 Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x500000 size 8192 bytes ........ done. ### JFFS2 load complete: 524288 bytes loaded to 0x800000 ## Starting application at 0x00800200
Re: Pogoplug E02: Squeeze install not booting multiple USB September 13, 2013 08:53PM |
Admin Registered: 13 years ago Posts: 18,560 |
> Loading file "/boot/uImage" from usb device 0:1 > (usbda1) > ** File not found /boot/uImage > Loading file "/boot/uInitrd" from usb device 0:1 > (usbda1) > ** File not found /boot/uInitrd
Re: Pogoplug E02: Squeeze install not booting multiple USB September 14, 2013 10:28AM |
Registered: 10 years ago Posts: 6 |
Re: Pogoplug E02: Squeeze install not booting multiple USB September 14, 2013 11:33AM |
Registered: 10 years ago Posts: 6 |
Re: Pogoplug E02: Squeeze install not booting multiple USB September 14, 2013 02:52PM |
Registered: 10 years ago Posts: 6 |
U-Boot 2011.12 (Feb 20 2012 - 21:21:59) Pogoplug E02 arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1 GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709 Hit any key to stop autoboot: 0 (Re)start USB... USB: Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Loading file "/rescueme" from usb device 0:1 (usbda1) ** File not found /rescueme reading /rescueme.txt ** Unable to read "/rescueme.txt" from usb 0:1 ** Creating 1 MTD partitions on "nand0": 0x000002500000-0x000008000000 : "mtd=3" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=3" UBI: MTD device size: 91 MiB UBI: number of good PEBs: 726 UBI: number of bad PEBs: 2 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 0 UBI: available PEBs: 715 UBI: total number of reserved PEBs: 11 UBI: number of PEBs reserved for bad PEB handling: 7 UBI: max/mean erase counter: 1/1 UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19 Error reading superblock on volume 'ubi:rootfs'! Loading file "/boot/uImage" from usb device 0:1 (usbda1) 1 bytes read Found bootable drive on usb 0:1 Loading file "/boot/uImage" from usb device 0:1 (usbda1) 2191504 bytes read Loading file "/boot/uInitrd" from usb device 0:1 (usbda1) 6483936 bytes read ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.10.4-kirkwood-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2191440 Bytes = 2.1 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-3.10.4-kirkwood-tld-1 Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6483872 Bytes = 6.2 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ...
Re: Pogoplug E02: Squeeze install not booting multiple USB September 14, 2013 04:51PM |
Admin Registered: 13 years ago Posts: 18,560 |
mkdir /media mkdir /media/sdb1 mount /dev/sdb1 /media/sdb1
cd /media/sdb1/boot mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-2.6.32-5-kirkwood -d /media/sdb1/boot/vmlinuz-2.6.32-5-kirkwood /media/sdb1/boot/uImage mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-2.6.32-5-kirkwood -d /media/sdb1/boot/initrd.img-2.6.32-5-kirkwood /media/sdb1/boot/uInitrd cd /media sync umount /media/sdb1
Re: Pogoplug E02: Squeeze install not booting multiple USB September 14, 2013 07:05PM |
Registered: 10 years ago Posts: 6 |
Re: Pogoplug E02: Squeeze install not booting multiple USB September 15, 2013 12:45AM |
Admin Registered: 13 years ago Posts: 18,560 |
Re: Pogoplug E02: Squeeze install not booting multiple USB September 15, 2013 01:26PM |
Registered: 10 years ago Posts: 6 |
Re: Pogoplug E02: Squeeze install not booting multiple USB September 15, 2013 07:45PM |
Admin Registered: 13 years ago Posts: 18,560 |
Re: Pogoplug E02: Squeeze install not booting multiple USB October 14, 2013 09:04AM |
Registered: 10 years ago Posts: 7 |
Re: Pogoplug E02: Squeeze install not booting multiple USB October 14, 2013 05:14PM |
Admin Registered: 13 years ago Posts: 18,560 |
Re: Pogoplug E02: Squeeze install not booting multiple USB October 15, 2013 08:54AM |
Registered: 10 years ago Posts: 7 |
Re: Pogoplug E02: Squeeze install not booting multiple USB October 16, 2013 12:32AM |
Admin Registered: 13 years ago Posts: 18,560 |