Problem with Zyxel NSA325 V2 an Network

U-Boot 2023.04-tld-1 (Jun 24 2023 - 17:50:21 -0700)
ZyXEL NSA325 2-Bay Power Media Server

SoC:   Kirkwood 88F6282_A1
Model: ZyXEL NSA325
DRAM:  512 MiB
Core:  19 devices, 15 uclasses, devicetree: separate
NAND:  128 MiB
Loading Environment from NAND... OK
Resetting console stdin/stdout/stderr to serial...
In:    serial
Out:   serial
Err:   serial
pcie0.0: Link up
Net:   eth0: ethernet-controller@72000
Hit any key to stop autoboot:  0
resetting USB...
Bus ehci@50000: USB EHCI 1.00
Bus xhci_pci: Register 4000820 NbrPorts 4
Starting the controller
USB XHCI 0.96
scanning bus ehci@50000 for devices... 3 USB Device(s) found
scanning bus xhci_pci for devices... 1 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
6389353 bytes read in 191 ms (31.9 MiB/s)
5792112 bytes read in 172 ms (32.1 MiB/s)
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-6.7.5-kirkwood-tld-1
   Created:      2024-04-07  13:52:21 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    6389289 Bytes = 6.1 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02100000 ...
   Image Name:   initramfs-6.7.5-kirkwood-tld-1
   Created:      2024-04-07  13:52:44 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    5792048 Bytes = 5.5 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
Working FDT set to 0


Starting kernel ...

   Loading Kernel Image
   Loading Ramdisk to 1f5c6000, end 1fb4c130 ... OK

Starting kernel ...

[    0.000000][    T0] Booting Linux on physical CPU 0x0
[    0.000000][    T0] Linux version 6.7.5-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 PREEMPT Sat Feb 17 16:27:56 PST 2024
[    0.000000][    T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000][    T0] CPU: VIVT data cache, VIVT instruction cache
[    0.000000][    T0] OF: fdt: Machine model: Seagate GoFlex Net
[    0.000000][    T0] printk: legacy bootconsole [earlycon0] enabled
[    0.000000][    T0] Memory policy: Data cache writeback
[    0.000000][    T0] Zone ranges:
[    0.000000][    T0]   Normal   [mem 0x0000000000000000-0x000000001fffffff]
[    0.000000][    T0] Movable zone start for each node
[    0.000000][    T0] Early memory node ranges
[    0.000000][    T0]   node   0: [mem 0x0000000000000000-0x000000001fffffff]
[    0.000000][    T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000001fffffff]
[    0.000000][    T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial
[    0.000000][    T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000][    T0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000][    T0] Built 1 zonelists, mobility grouping on.  Total pages: 129920
[    0.000000][    T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[    0.000000][    T0] Memory: 491848K/524288K available (12288K kernel code, 1781K rwdata, 5588K rodata, 1024K init, 309K bss, 32440K reserved, 0K cma-reserved)
[    0.000000][    T0] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000][    T0] trace event string verifier disabled
[    0.000000][    T0] rcu: Preemptible hierarchical RCU implementation.
[    0.000000][    T0]  Trampoline variant of Tasks RCU enabled.
[    0.000000][    T0]  Tracing variant of Tasks RCU enabled.
[    0.000000][    T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000][    T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000][    T0] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000][    T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[    0.000001][    T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[    0.008650][    T0] Switching to timer-based delay loop, resolution 5ns
[    0.015992][    T0] Console: colour dummy device 80x30
[    0.021268][    T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000)
[    0.032598][    T0] CPU: Testing write buffer coherency: ok
[    0.038327][    T0] pid_max: default: 32768 minimum: 301
[    0.050501][    T0] LSM: initializing lsm=capability,integrity
[    0.058235][    T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.066350][    T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.085759][    T1] RCU Tasks: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[    0.093935][    T1] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[    0.102682][    T1] Setting up static identity map for 0x100000 - 0x100058
[    0.109937][    T1] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1
[    0.116229][    T1] rcu: Hierarchical SRCU implementation.
[    0.121831][    T1] rcu:     Max phase no-delay instances is 1000.
[    0.130272][    T1] devtmpfs: initialized
[    0.142646][    T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.153334][    T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.163355][    T1] prandom: seed boundary self test passed
[    0.172184][    T1] prandom: 100 self tests passed
[    0.177011][    T1] pinctrl core: initialized pinctrl subsystem
[    0.187065][    T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.194533][    T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.206297][    T1] audit: initializing netlink subsys (disabled)
[    0.214387][    T1] thermal_sys: Registered thermal governor 'step_wise'
[    0.214504][   T20] audit: type=2000 audit(0.200:1): state=initialized audit_enabled=0 res=1
[    0.229849][    T1] cpuidle: using governor ladder
[    0.234748][    T1] cpuidle: using governor menu
[    0.239945][    T1] Feroceon L2: Enabling L2
[    0.244274][    T1] Feroceon L2: Cache support initialised.
[    0.257466][    T1] No ATAGs?
[    0.628663][    T1] raid6: int32x8  gen()   152 MB/s
[    0.968665][    T1] raid6: int32x4  gen()   140 MB/s
[    1.308664][    T1] raid6: int32x2  gen()   181 MB/s
[    1.648661][    T1] raid6: int32x1  gen()   131 MB/s
[    1.653661][    T1] raid6: using algorithm int32x2 gen() 181 MB/s
[    2.008661][    T1] raid6: .... xor() 115 MB/s, rmw enabled
[    2.014268][    T1] raid6: using intx1 recovery algorithm
[    2.040130][    T1] SCSI subsystem initialized
[    2.045257][    T1] usbcore: registered new interface driver usbfs
[    2.058728][    T1] usbcore: registered new interface driver hub
[    2.064816][    T1] usbcore: registered new device driver usb
[    2.088955][    T1] pps_core: LinuxPPS API ver. 1 registered
[    2.094640][    T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    2.118696][    T1] PTP clock support registered
[    2.125619][    T1] vgaarb: loaded
[    2.139378][    T1] clocksource: Switched to clocksource orion_clocksource
[    2.166193][    T1] VFS: Disk quotas dquot_6.6.0
[    2.179737][    T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    2.221867][    T1] NET: Registered PF_INET protocol family
[    2.227761][    T1] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    2.251483][    T1] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    2.269555][    T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    2.278087][    T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    2.309458][    T1] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    2.317865][    T1] TCP: Hash tables configured (established 4096 bind 4096)
[    2.339946][    T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
[    2.348096][    T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    2.369415][    T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    2.377913][    T1] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    2.400357][    T1] RPC: Registered named UNIX socket transport module.
[    2.407009][    T1] RPC: Registered udp transport module.
[    2.429393][    T1] RPC: Registered tcp transport module.
[    2.434825][    T1] RPC: Registered tcp-with-tls transport module.
[    2.449393][    T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    2.456578][    T1] PCI: CLS 0 bytes, default 32
[    2.469989][   T19] Trying to unpack rootfs image as initramfs...
[    3.230016][   T19] Freeing initrd memory: 5660K
[    3.358765][    T1] Initialise system trusted keyrings
[    3.364854][    T1] Key type blacklist registered
[    3.369947][    T1] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[    3.377179][    T1] zbud: loaded
[    3.394338][    T1] NFS: Registering the id_resolver key type
[    3.400182][    T1] Key type id_resolver registered
[    3.405082][    T1] Key type id_legacy registered
[    3.409976][    T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    3.417451][    T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[    3.426981][    T1] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    3.435517][    T1] fuse: init (API version 7.39)
[    3.441495][    T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[    3.448947][    T1] orangefs_init: module version upstream loaded
[    3.455392][    T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled
[    3.679347][    T1] xor: measuring software checksum speed
[    3.691514][    T1]    arm4regs        :  1492 MB/sec
[    3.707588][    T1]    8regs           :   895 MB/sec
[    3.720430][    T1]    32regs          :  1270 MB/sec
[    3.725506][    T1] xor: using function: arm4regs (1492 MB/sec)
[    3.731474][    T1] async_tx: api initialized (async)
[    3.736554][    T1] Key type asymmetric registered
[    3.741385][    T1] Asymmetric key parser 'x509' registered
[    3.787437][    T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[    3.796207][    T1] io scheduler bfq registered
[    3.942410][    T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    3.951912][    T1] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
[    3.962612][    T1] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation.
[    3.973481][    T1] mv_xor f1060800.xor: Marvell shared XOR driver
[    4.041429][    T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    4.053412][    T1] mv_xor f1060900.xor: Marvell shared XOR driver
[    4.121420][    T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    4.133631][    T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    4.142942][    T1] printk: legacy console [ttyS0] disabled
[    4.149131][    T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 27, base_baud = 12500000) is a 16550A
[    4.158952][    T1] printk: legacy console [ttyS0] enabled
[    4.158952][    T1] printk: legacy console [ttyS0] enabled
[    4.170075][    T1] printk: legacy bootconsole [earlycon0] disabled
[    4.170075][    T1] printk: legacy bootconsole [earlycon0] disabled
[    4.209772][    T1] loop: module loaded
[    4.214577][    T1] sata_mv f1080000.sata: slots 32 ports 2
[    4.224143][    T1] scsi host0: sata_mv
[    4.229283][    T1] scsi host1: sata_mv
[    4.233589][    T1] ata1: SATA max UDMA/133 irq 28 lpm-pol 0
[    4.239283][    T1] ata2: SATA max UDMA/133 irq 28 lpm-pol 0
[    4.246030][    T1] nand: device found, Manufacturer ID: 0x92, Chip ID: 0xf1
[    4.253182][    T1] nand: Eon NAND 128MiB 3,3V 8-bit
[    4.258178][    T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    4.266532][    T1] Scanning device for bad blocks
[    4.276706][    T1] Bad eraseblock 100 at 0x000000c80000
[    4.287346][    T1] Bad eraseblock 200 at 0x000001900000
[    4.336264][    T1] 4 fixed-partitions partitions found on MTD device orion_nand
[    4.343727][    T1] Creating 4 MTD partitions on "orion_nand":
[    4.349609][    T1] 0x000000000000-0x000000100000 : "u-boot"
[    4.356043][    T1] 0x000000100000-0x000000500000 : "uImage"
[    4.362371][    T1] 0x000000500000-0x000002500000 : "pogoplug"
[    4.368961][    T1] 0x000002500000-0x00000fd00000 : "root"
[    4.374502][    T1] mtd: partition "root" extends beyond the end of device "orion_nand" -- size truncated to 0x5b00000
[    4.386862][    T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[    4.395470][    T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[    4.409527][    T1] mdio_bus f1072004.mdio-bus-mii: MDIO device at address 0 is missing.
[    4.417885][    T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    4.426754][    T1] orion-ehci f1050000.ehci: EHCI Host Controller
[    4.433086][    T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    4.441735][    T1] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000
[    4.469426][    T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    4.476523][    T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.07
[    4.485581][    T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.493576][    T1] usb usb1: Product: EHCI Host Controller
[    4.499206][    T1] usb usb1: Manufacturer: Linux 6.7.5-kirkwood-tld-1 ehci_hcd
[    4.506583][    T1] usb usb1: SerialNumber: f1050000.ehci
[    4.512919][    T1] hub 1-0:1.0: USB hub found
[    4.517470][    T1] hub 1-0:1.0: 1 port detected
[    4.523015][    T1] usbcore: registered new interface driver usb-storage
[    4.530356][    T1] mousedev: PS/2 mouse device common for all mice
[    4.582293][   T53] ata1: SATA link down (SStatus 0 SControl F300)
[    4.809409][    T8] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    4.930897][   T55] ata2: SATA link down (SStatus 0 SControl F300)
[    5.011113][    T8] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=85.32
[    5.020069][    T8] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    5.027956][    T8] usb 1-1: Product: USB2.0 Hub
[    5.033615][    T8] hub 1-1:1.0: USB hub found
[    5.038492][    T8] hub 1-1:1.0: 4 ports detected
[    5.359402][    T8] usb 1-1.2: new high-speed USB device number 3 using orion-ehci
[    5.510615][    T8] usb 1-1.2: New USB device found, idVendor=0781, idProduct=55a3, bcdDevice= 1.00
[    5.519742][    T8] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    5.527813][    T8] usb 1-1.2: Product:  SanDisk 3.2Gen1
[    5.533172][    T8] usb 1-1.2: Manufacturer:  USB
[    5.537900][    T8] usb 1-1.2: SerialNumber: 0101fa8ba328daf2a7dff770070d5a292729e1de726d31521c70d65204c17465c579000000000000000000005bd6fd25008d4000a35581079dab63eb
[    5.553684][    T8] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[    5.561514][    T8] scsi host2: usb-storage 1-1.2:1.0
[    5.609406][    T1] rtc-mv f1010300.rtc: internal RTC not ticking
[    5.615760][    T1] i2c_dev: i2c /dev entries driver
[    5.621732][    T1] device-mapper: uevent: version 1.0.3
[    5.627566][    T1] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com
[    5.637348][    T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[    5.644677][    T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[    5.652054][    T1] device-mapper: multipath service-time: version 0.3.0 loaded
[    5.659583][    T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[    5.667119][    T1] sdhci: Secure Digital Host Controller Interface driver
[    5.674066][    T1] sdhci: Copyright(c) Pierre Ossman
[    5.681482][    T1] ledtrig-cpu: registered to indicate activity on CPUs
[    5.688313][    T1] hid: raw HID events driver (C) Jiri Kosina
[    5.694687][    T1] drop_monitor: Initializing network drop monitor service
[    5.703115][    T1] NET: Registered PF_INET6 protocol family
[    5.710795][    T1] Segment Routing with IPv6
[    5.715187][    T1] RPL Segment Routing with IPv6
[    5.720011][    T1] In-situ OAM (IOAM) with IPv6
[    5.724778][    T1] NET: Registered PF_PACKET protocol family
[    5.730990][    T1] Key type dns_resolver registered
[    5.751527][    T1] registered taskstats version 1
[    5.756499][    T1] Loading compiled-in X.509 certificates
[    5.792623][    T1] Key type .fscrypt registered
[    5.797287][    T1] Key type fscrypt-provisioning registered
[    5.807587][    T1] Key type big_key registered
[    5.983332][    T1] Key type encrypted registered
[    6.068180][  T115] "cryptomgr_test" (115) uses obsolete ecb(arc4) skcipher
[    6.572032][   T11] scsi 2:0:0:0: Direct-Access      USB      SanDisk 3.2Gen1 1.00 PQ: 0 ANSI: 6
[    6.591390][   T30] sd 2:0:0:0: [sda] 240353280 512-byte logical blocks: (123 GB/115 GiB)
[    6.610144][   T30] sd 2:0:0:0: [sda] Write Protect is off
[    6.616383][   T30] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    6.647228][   T30]  sda: sda1
[    6.650891][   T30] sd 2:0:0:0: [sda] Attached SCSI removable disk
[    7.824149][    T1] clk: Disabling unused clocks
[    7.832122][    T1] Freeing unused kernel image (initmem) memory: 1024K
[    7.859988][    T1] Checked W+X mappings: passed, no W+X pages found
[    7.866396][    T1] Run /init as init process
Loading, please wait...
Starting systemd-udevd version 252.17-1~deb12u1
[    8.995590][  T167] usbcore: registered new interface driver uas
Begin: Loading essential drivers ... done.
[   19.049737][   T49] platform mv643xx_eth_port.0: deferred probe pending
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.38.1
[/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1
rootfs: recovering journal
rootfs: clean, 23081/7512064 files, 851952/30043904 blocks
done.
[   20.383420][  T186] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[   20.632632][  T186] EXT4-fs (sda1): mounted filesystem 3cc46040-e3cc-4f11-a2e6-effa4630a110 ro with ordered data mode. Quota mode: none.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 3.06 booting
INIT: No inittab.d directory found
Using makefile-style concurrent boot in runlevel S.
Setting hostname to 'debian'...done.
Starting hotplug events dispatcher: systemd-udevd.
Synthesizing the initial hotplug events (subsystems)...done.
Synthesizing the initial hotplug events (devices)...done.
Waiting for /dev to be fully populated...[   23.572608][  T371] orion_wdt: Initial timeout 21 sec
[   24.121710][  T367] marvell-cesa f1030000.crypto: CESA device successfully registered
[   24.249738][  T364] sd 2:0:0:0: Attached scsi generic sg0 type 0
done.
Activating swap:.
[   25.533288][  T513] EXT4-fs (sda1): re-mounted 3cc46040-e3cc-4f11-a2e6-effa4630a110 r/w. Quota mode: none.
[   25.929479][    C0] random: crng init done
Will now check all file systems.
Checking all file systems.
LABEL=rootfs is mounted
Done checking file systems.
Log is being saved in /var/log/fsck/checkfs if that location is writable.
Cleaning up temporary files...Cleaning /tmp...done.
 /tmp.
Will now mount local filesystems:.
Will now activate swapfile swap, if any:done.
Checking minimum space in /tmp...done.
Cleaning up temporary files....
Starting Setting kernel variables: sysctl.
Initializing random number generator...done.
Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.3-P1
Copyright 2004-2022 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Cannot find device "eth0"
Failed to get interface index: No such device

If you think you have received this message due to a bug rather
than a configuration issue please read the section on submitting
bugs on either our web page at www.isc.org or in the README file
before submitting a bug.  These pages explain the proper
process and the information we find helpful for debugging.

exiting.
ifup: failed to bring up eth0
failed.
Starting RPC port mapper daemon: rpcbind.
Starting NFS common utilities: statd idmapd.
Cleaning up temporary files....
INIT: Entering runlevel: 2
Using makefile-style concurrent boot in runlevel 2.
Not starting NFS kernel daemon: no exports ... (warning).
Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
996 (syslogd)
.
Starting system message bus: dbus.
Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
Starting NTP server: ntpd1969-12-31T16:00:30 ntpd[1041]: INIT: ntpd ntpsec-1.2.2: Starting
1969-12-31T16:00:30 ntpd[1041]: INIT: Command line: /usr/sbin/ntpd -p /var/run/ntpd.pid -g -u 104:106
.
Starting NTP server: ntpd.
Starting OpenBSD Secure Shell server: sshd.
Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1021 (klogd)
.
Running local boot scripts (/etc/rc.local)
.

Debian GNU/Linux 12 debian ttyS0

debian login:

arch=arm
baudrate=115200
board=nsa325
board_name=nsa325
boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefi                                                                                                                                                             x}${script}; source ${scriptaddr}
boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr}                                                                                                                                                              ${prefix}${boot_syslinux_conf}
boot_net_usb_start=usb start
boot_pci_enum=pci enum
boot_prefixes=/ /boot/
boot_script_dhcp=boot.scr.uimg
boot_scripts=boot.scr.uimg boot.scr
boot_syslinux_conf=extlinux/extlinux.conf
boot_targets=usb0 sata0 dhcp
bootcmd=usb reset; run usb_bootcmd; usb stop; reset
bootcmd_dhcp=devtype=dhcp; run boot_net_usb_start; run boot_pci_enum; if dhcp ${                                                                                                                                                             scriptaddr} ${boot_script_dhcp}; then source ${scriptaddr}; fi;
bootcmd_sata0=devnum=0; run sata_boot
bootcmd_usb0=devnum=0; run usb_boot
bootdelay=10
console=ttyS0,115200
cpu=arm926ejs
distro_bootcmd=for target in ${boot_targets}; do run bootcmd_${target}; done
dtb_file=/boot/dts/kirkwood-nsa310.dtb
ethact=eth0
ethaddr=5C:F4:AB:DE:EB:1A
fdt_addr_r=0x2c00000
fdtcontroladdr=1fb516e0
fdtfile=kirkwood-nsa325.dtb
kernel_addr_r=0x800000
load_uimage=ext2load usb 0:1 0x800000 /boot/uImage
load_uinitrd=ext2load usb 0:1 0x2100000 /boot/uInitrd
loadaddr=0x800000
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(ke                                                                                                                                                             y_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00                                                                                                                                                             000(kernel_2),0x2FC0000(rootfs2)
ramdisk_addr_r=0x01100000
sata_boot=if sata dev ${devnum}; then devtype=sata; run scan_dev_for_boot_part;                                                                                                                                                              fi
scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for                                                                                                                                                              prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scrip                                                                                                                                                             ts; done;
scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env ex                                                                                                                                                             ists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fs                                                                                                                                                             type ${devtype} ${devnum}:${distro_bootpart} bootfstype; then part uuid ${devtyp                                                                                                                                                             e} ${devnum}:${distro_bootpart} distro_bootpart_uuid ; run scan_dev_for_boot; fi                                                                                                                                                             ; done; setenv devplist
scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefi                                                                                                                                                             x}${boot_syslinux_conf}; then echo Found ${prefix}${boot_syslinux_conf}; run boo                                                                                                                                                             t_extlinux; echo EXTLINUX FAILED: continuing...; fi
scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${d                                                                                                                                                             evnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${pr                                                                                                                                                             efix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done
scriptaddr=0x200000
soc=kirkwood
ubifs_boot=if ubi part ${bootubipart} ${bootubioff} && ubifsmount ubi0:${bootubi                                                                                                                                                             vol}; then devtype=ubi; devnum=ubi0; bootfstype=ubifs; distro_bootpart=${bootubi                                                                                                                                                             vol}; run scan_dev_for_boot; ubifsumount; fi
usb_boot=mw 0x800000 0 1; run load_uimage; run load_uinitrd; bootm 0x800000 0x21                                                                                                                                                             00000
usb_bootcmd=run usb_set_bootargs; run usb_boot
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdela                                                                                                                                                             y=10 earlyprintk=serial
vendor=zyxel
ver=U-Boot 2023.04-tld-1 (Jun 24 2023 - 17:50:21 -0700)\
ZyXEL NSA325 2-Bay Power Media Server

Quote

4. (Stock u-boot only) Create uImage with embedded DTB for booting with older u-boots (2012 or earlier). Skip this step if you have installed the latest U-Boot for Kirkwood (or are installing this u-boot at the same time, or running kwboot with latest u-boot image).

Please replace kirkwood-goflexnet.dtb below with the correct DTB name for your box (see the folder /media/sdb1/boot/dts for the exact spelling of your Kirkwood box name).

Generate the uImage with DTB embedded inside:
cd /media/sdb1/boot
cp -a zImage-6.5.7-kirkwood-tld-1 zImage.fdt
cat dts/kirkwood-goflexnet.dtb >> zImage.fdt
mv uImage uImage.orig
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-6.5.7-kirkwood-tld-1 -d zImage.fdt uImage
sync

cat dts/kirkwood-nsa325.dtb  >> zImage.fdt