|
Netgear Stora MS2000 - Detecting USB drives via latest uboot is inconsistent September 17, 2024 12:40PM |
Registered: 25 days ago Posts: 4 |
simon@X220:~/Downloads/uboot.2017.07-tld-1.netgear_ms2110.bodhi$ sudo kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.netgear_ms2110.mtd0.kwb -p
kwboot version 2024.01
Detected kwbimage v0 with NAND boot signature
Patching image boot signature to UART
Sending boot message. Please reboot the target...-
Sending boot image header (512 bytes)...
25 % [.... ]
Done
Sending boot image data (500964 bytes)...
0 % [......................................................................]
1 % [......................................................................]
3 % [......................................................................]
5 % [......................................................................]
7 % [......................................................................]
8 % [......................................................................]
10 % [......................................................................]
12 % [......................................................................]
14 % [......................................................................]
16 % [......................................................................]
17 % [......................................................................]
19 % [......................................................................]
21 % [......................................................................]
23 % [......................................................................]
25 % [......................................................................]
26 % [......................................................................]
28 % [......................................................................]
30 % [......................................................................]
32 % [......................................................................]
34 % [......................................................................]
35 % [......................................................................]
37 % [......................................................................]
39 % [......................................................................]
41 % [......................................................................]
42 % [......................................................................]
44 % [......................................................................]
46 % [......................................................................]
48 % [......................................................................]
50 % [......................................................................]
51 % [......................................................................]
53 % [......................................................................]
55 % [......................................................................]
57 % [......................................................................]
59 % [......................................................................]
60 % [......................................................................]
62 % [......................................................................]
64 % [......................................................................]
66 % [......................................................................]
67 % [......................................................................]
69 % [......................................................................]
71 % [......................................................................]
73 % [......................................................................]
75 % [......................................................................]
76 % [......................................................................]
78 % [......................................................................]
80 % [......................................................................]
82 % [......................................................................]
84 % [......................................................................]
85 % [......................................................................]
87 % [......................................................................]
89 % [......................................................................]
91 % [......................................................................]
93 % [......................................................................]
94 % [......................................................................]
96 % [......................................................................]
98 % [................................................................ ]
Done
Finishing transfer
[Type Ctrl-\ + c to quit]
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:38:05 -0700)
Netgear Stora MS2110
SoC: Kirkwood 88F6281_A1
DRAM: 128 MiB
WARNING: Caches not enabled
NAND: 256 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: egiga0
PHY reset timed out
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
Netgear Stora> printenv
arcNumber=2743
baudrate=115200
bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset
bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm$load_uimage_addr; fi; fi
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootdelay=10
bootdev=usb
console=console=ttyS0,115200
device=0:1
devices=usb ide
disks=0 1 2 3
dtb_file=/boot/dts/kirkwood-netgear_stora_ms2000
ethact=egiga0
ethaddr=52:3b:20:9c:11:51
if_netconsole=ping $serverip
ipaddr=192.168.0.231
led_error=orange blinking
led_exit=green off
led_init=green blinking
load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file
load_dtb_addr=0x1c00000
load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd
load_initrd_addr=0x1100000
load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage
load_uimage_addr=0x800000
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1m(uboot),4m@1m(kernel),251m@5m(rootfs) rw
partition=nand0,2
preboot_nc=run if_netconsole start_netconsole
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done
serverip=192.168.0.220
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
uenv_addr=0x810000
uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize
uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done;
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi
usb_ready_retry=15
Environment size: 2905/131068 bytes
Netgear Stora> setenv dtb_file '/boot/dts/kirkwood-netgear_stora_ms2000.dtb'
Netgear Stora> printenv
arcNumber=2743
baudrate=115200
bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset
bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm$load_uimage_addr; fi; fi
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootdelay=10
bootdev=usb
console=console=ttyS0,115200
device=0:1
devices=usb ide
disks=0 1 2 3
dtb_file=/boot/dts/kirkwood-netgear_stora_ms2000.dtb
ethact=egiga0
ethaddr=52:3b:20:9c:11:51
if_netconsole=ping $serverip
ipaddr=192.168.0.231
led_error=orange blinking
led_exit=green off
led_init=green blinking
load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file
load_dtb_addr=0x1c00000
load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd
load_initrd_addr=0x1100000
load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage
load_uimage_addr=0x800000
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1m(uboot),4m@1m(kernel),251m@5m(rootfs) rw
partition=nand0,2
preboot_nc=run if_netconsole start_netconsole
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done
serverip=192.168.0.220
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
uenv_addr=0x810000
uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize
uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done;
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi
usb_ready_retry=15
Environment size: 2909/131068 bytes
Netgear Stora> boot
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices...
|
Re: Netgear Stora MS2000 - Detecting USB drives via latest uboot is inconsistent September 18, 2024 06:55PM |
Admin Registered: 13 years ago Posts: 18,898 |
|
Re: Netgear Stora MS2000 - Detecting USB drives via latest uboot is inconsistent September 19, 2024 04:50PM |
Registered: 25 days ago Posts: 4 |
root@node-01:~# fdisk /dev/sdb
Welcome to fdisk (util-linux 2.38.1).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.
Command (m for help): d
Selected partition 1
Partition 1 has been deleted.
Command (m for help): d
No partition is defined yet!
Command (m for help): n
Partition type
p primary (0 primary, 0 extended, 4 free)
e extended (container for logical partitions)
Select (default p):
Using default response p.
Partition number (1-4, default 1):
First sector (2048-60538880, default 2048):
Last sector, +/-sectors or +/-size{K,M,G,T,P} (2048-60538880, default 60538880):
Created a new partition 1 of type 'Linux' and of size 28.9 GiB.
Partition #1 contains a ext3 signature.
Do you want to remove the signature? [Y]es/[N]o: y
The signature will be removed by a write command.
Command (m for help): w
The partition table has been altered.
Calling ioctl() to re-read partition table.
Syncing disks.
root@node-01:~# mkfs.ext4 /dev/sdb1
mke2fs 1.47.0 (5-Feb-2023)
Creating filesystem with 7567104 4k blocks and 1892352 inodes
Filesystem UUID: 9c964fa3-5a78-4ad9-b002-47eacb9522ad
Superblock backups stored on blocks:
32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208,
4096000
Allocating group tables: done
Writing inode tables: done
Creating journal (32768 blocks): done
Writing superblocks and filesystem accounting information: done
root@node-01:/media/sdb1# sha256sum Debian-5.6.7-kirkwood-tld-1-rootfs-bodhi.tar.bz2 04a2dba61dc3284fbbfb5ac9b439655f2fc44293cd228dce2b774d37b4512fd3 Debian-5.6.7-kirkwood-tld-1-rootfs-bodhi.tar.bz2
root@node-01:/media/sdb1# tar xjf Debian-5.6.7-kirkwood-tld-1-rootfs-bodhi.tar.bz2 root@node-01:/media/sdb1# ls bin boot Debian-5.6.7-kirkwood-tld-1-rootfs-bodhi.tar.bz2 dev etc home lib lost+found media mnt opt proc root run sbin srv sys tmp usr var root@node-01:/media/sdb1# cat ./etc/fstab # /etc/fstab: static file system information. # # <file system> <mount point> <type> <options> <dump> <pass> LABEL=rootfs / ext3 noatime,errors=remount-ro 0 1 tmpfs /tmp tmpfs defaults 0 0 root@node-01:/media/sdb1# nano /media/sdb1/etc/fstab root@node-01:/media/sdb1# cat ./etc/fstab # /etc/fstab: static file system information. # # <file system> <mount point> <type> <options> <dump> <pass> LABEL=rootfs / ext4 noatime,errors=remount-ro 0 1 tmpfs /tmp tmpfs defaults 0 0 root@node-01:/media/sdb1# cd ~ root@node-01:~# umount /media/sdb1
simon@X220:~/Downloads/uboot.2017.07-tld-1.netgear_ms2110.bodhi$ sudo kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.netgear_ms2110.mtd0.kwb -p
kwboot version 2024.01
Detected kwbimage v0 with NAND boot signature
Patching image boot signature to UART
Sending boot message. Please reboot the target...-
Sending boot image header (512 bytes)...
25 % [.... ]
Done
Sending boot image data (500964 bytes)...
0 % [......................................................................]
1 % [......................................................................]
3 % [......................................................................]
5 % [......................................................................]
7 % [......................................................................]
8 % [......................................................................]
10 % [......................................................................]
12 % [......................................................................]
14 % [......................................................................]
16 % [......................................................................]
17 % [......................................................................]
19 % [......................................................................]
21 % [......................................................................]
23 % [......................................................................]
25 % [......................................................................]
26 % [......................................................................]
28 % [......................................................................]
30 % [......................................................................]
32 % [......................................................................]
34 % [......................................................................]
35 % [......................................................................]
37 % [......................................................................]
39 % [......................................................................]
41 % [......................................................................]
42 % [......................................................................]
44 % [......................................................................]
46 % [......................................................................]
48 % [......................................................................]
50 % [......................................................................]
51 % [......................................................................]
53 % [......................................................................]
55 % [......................................................................]
57 % [......................................................................]
59 % [......................................................................]
60 % [......................................................................]
62 % [......................................................................]
64 % [......................................................................]
66 % [......................................................................]
67 % [......................................................................]
69 % [......................................................................]
71 % [......................................................................]
73 % [......................................................................]
75 % [......................................................................]
76 % [......................................................................]
78 % [......................................................................]
80 % [......................................................................]
82 % [......................................................................]
84 % [......................................................................]
85 % [......................................................................]
87 % [......................................................................]
89 % [......................................................................]
91 % [......................................................................]
93 % [......................................................................]
94 % [......................................................................]
96 % [......................................................................]
98 % [................................................................ ]
Done
Finishing transfer
[Type Ctrl-\ + c to quit]
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:38:05 -0700)
Netgear Stora MS2110
SoC: Kirkwood 88F6281_A1
DRAM: 128 MiB
WARNING: Caches not enabled
NAND: 256 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: egiga0
PHY reset timed out
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
Netgear Stora>printenv
arcNumber=2743
baudrate=115200
bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset
bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm$load_uimage_addr; fi; fi
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootdelay=10
bootdev=usb
console=console=ttyS0,115200
device=0:1
devices=usb ide
disks=0 1 2 3
dtb_file=/boot/dts/kirkwood-netgear_stora_ms2000
ethact=egiga0
ethaddr=52:3b:20:9c:11:51
if_netconsole=ping $serverip
ipaddr=192.168.0.231
led_error=orange blinking
led_exit=green off
led_init=green blinking
load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file
load_dtb_addr=0x1c00000
load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd
load_initrd_addr=0x1100000
load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage
load_uimage_addr=0x800000
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1m(uboot),4m@1m(kernel),251m@5m(rootfs) rw
partition=nand0,2
preboot_nc=run if_netconsole start_netconsole
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done
serverip=192.168.0.220
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
uenv_addr=0x810000
uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize
uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done;
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi
usb_ready_retry=15
Environment size: 2905/131068 bytes
Netgear Stora> usb reset
resetting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
simon@X220:~/Downloads/uboot.2017.07-tld-1.netgear_ms2110.bodhi$ sudo kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.netgear_ms2110.mtd0.kwb -p
kwboot version 2024.01
Detected kwbimage v0 with NAND boot signature
Patching image boot signature to UART
Sending boot message. Please reboot the target...-
Sending boot image header (512 bytes)...
25 % [.... ]
Done
Sending boot image data (500964 bytes)...
0 % [......................................................................]
1 % [......................................................................]
3 % [......................................................................]
5 % [......................................................................]
7 % [......................................................................]
8 % [......................................................................]
10 % [......................................................................]
12 % [......................................................................]
14 % [......................................................................]
16 % [......................................................................]
17 % [......................................................................]
19 % [......................................................................]
21 % [......................................................................]
23 % [......................................................................]
25 % [......................................................................]
26 % [......................................................................]
28 % [......................................................................]
30 % [......................................................................]
32 % [......................................................................]
34 % [......................................................................]
35 % [......................................................................]
37 % [......................................................................]
39 % [......................................................................]
41 % [......................................................................]
42 % [......................................................................]
44 % [......................................................................]
46 % [......................................................................]
48 % [......................................................................]
50 % [......................................................................]
51 % [......................................................................]
53 % [......................................................................]
55 % [......................................................................]
57 % [......................................................................]
59 % [......................................................................]
60 % [......................................................................]
62 % [......................................................................]
64 % [......................................................................]
66 % [......................................................................]
67 % [......................................................................]
69 % [......................................................................]
71 % [......................................................................]
73 % [......................................................................]
75 % [......................................................................]
76 % [......................................................................]
78 % [......................................................................]
80 % [......................................................................]
82 % [......................................................................]
84 % [......................................................................]
85 % [......................................................................]
87 % [......................................................................]
89 % [......................................................................]
91 % [......................................................................]
93 % [......................................................................]
94 % [......................................................................]
96 % [......................................................................]
98 % [................................................................ ]
Done
Finishing transfer
[Type Ctrl-\ + c to quit]
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:38:05 -0700)
Netgear Stora MS2110
SoC: Kirkwood 88F6281_A1
DRAM: 128 MiB
WARNING: Caches not enabled
NAND: 256 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: egiga0
PHY reset timed out
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
Netgear Stora> printenv
arcNumber=2743
baudrate=115200
bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset
bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm$load_uimage_addr; fi; fi
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootdelay=10
bootdev=usb
console=console=ttyS0,115200
device=0:1
devices=usb ide
disks=0 1 2 3
dtb_file=/boot/dts/kirkwood-netgear_stora_ms2000
ethact=egiga0
ethaddr=52:3b:20:9c:11:51
if_netconsole=ping $serverip
ipaddr=192.168.0.231
led_error=orange blinking
led_exit=green off
led_init=green blinking
load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file
load_dtb_addr=0x1c00000
load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd
load_initrd_addr=0x1100000
load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage
load_uimage_addr=0x800000
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1m(uboot),4m@1m(kernel),251m@5m(rootfs) rw
partition=nand0,2
preboot_nc=run if_netconsole start_netconsole
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done
serverip=192.168.0.220
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
uenv_addr=0x810000
uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize
uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done;
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi
usb_ready_retry=15
Environment size: 2905/131068 bytes
Netgear Stora> usb reset
resetting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices...
Use USB retry period from the environment: 15 second(s)
1 Storage Device(s) found
Netgear Stora> setenv dtb_file '/boot/dts/kirkwood-netgear_stora_ms2000.dtb'
Netgear Stora> boot
Reset IDE: ide_preinit failed
Partition Map for USB device 0 -- Partition Type: DOS
Part Start Sector Num Sectors UUID Type
1 2048 60536833 e50dcb51-01 83
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **
no IDE devices available
running scan_disk ...
Scan device usb
device usb 0:1
1 bytes read in 692 ms (0 Bytes/s)
Found bootable drive on usb 0
loading uImage ...
6223944 bytes read in 882 ms (6.7 MiB/s)
loading uInitrd ...
5791271 bytes read in 778 ms (7.1 MiB/s)
loading DTB /boot/dts/kirkwood-netgear_stora_ms2000.dtb ...
11715 bytes read in 2906 ms (3.9 KiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-6.5.7-kirkwood-tld-1
Created: 2023-10-31 22:53:22 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 6223880 Bytes = 5.9 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-6.5.7-kirkwood-tld-1
Created: 2023-10-31 22:53:55 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5791207 Bytes = 5.5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
Booting using the fdt blob at 0x1c00000
Loading Kernel Image ... OK
Loading Ramdisk to 03a7a000, end 03fffde7 ... OK
Loading Device Tree to 03a74000, end 03a79dc2 ... OK
Starting kernel ...
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE
U-Boot 1.1.4 (Sep 4 2009 - 09:36:11) Marvell version: 3.4.14
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE60
Soc: MV88F6281 Rev 3 (DDR2)
CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 333Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 64MB
DRAM CS[1] base 0x04000000 size 64MB
DRAM Total size 128MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
|
Re: Netgear Stora MS2000 - Detecting USB drives via latest uboot is inconsistent September 19, 2024 08:08PM |
Registered: 1 year ago Posts: 96 |
> root@node-01:~# mkfs.ext4 /dev/sdb1 > mke2fs 1.47.0 (5-Feb-2023) > Creating filesystem with 7567104 4k blocks and > 1892352 inodes > Filesystem UUID: > 9c964fa3-5a78-4ad9-b002-47eacb9522ad > Superblock backups stored on blocks: > 32768, 98304, 163840, 229376, 294912, > 819200, 884736, 1605632, 2654208, > 4096000 > > Allocating group tables: done > Writing inode tables: done > Creating journal (32768 blocks): done > Writing superblocks and filesystem accounting > information: done
Quote
But be aware that Ext4 file system format needs to be "finalized" before it can be used for booting.
Quote
Disable the lazy option while formatting it:
mkfs.ext4 -E lazy_itable_init=0
|
Re: Netgear Stora MS2000 - Detecting USB drives via latest uboot is inconsistent September 19, 2024 11:48PM |
Admin Registered: 13 years ago Posts: 18,898 |
mkfs.ext3 -L rootfs /dev/sdb1and for Ext4 rootfs
mkfs.ext4 -L rootfs -E lazy_itable_init=0 /dev/sdb1
setenv dtb_file '/boot/dts/kirkwood-netgear_stora_ms2000.dtb' setenv custom_params 'earlyprintk=serial' boot
|
Re: Netgear Stora MS2000 - Detecting USB drives via latest uboot is inconsistent September 20, 2024 09:25AM |
Registered: 25 days ago Posts: 4 |
root@node-01:~# mkfs.ext4 -L rootfs -E lazy_itable_init=0 /dev/sdb1
mke2fs 1.47.0 (5-Feb-2023)
Creating filesystem with 7567104 4k blocks and 1892352 inodes
Filesystem UUID: 7a4183bd-8d84-4bf7-951d-a7312419fcde
Superblock backups stored on blocks:
32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208,
4096000
Allocating group tables: done
Writing inode tables: done
Creating journal (32768 blocks): done
Writing superblocks and filesystem accounting information: done
simon@X220:~/Downloads/uboot.2017.07-tld-1.netgear_ms2110.bodhi$ sudo kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.netgear_ms2110.mtd0.kwb -p
kwboot version 2024.01
Detected kwbimage v0 with NAND boot signature
Patching image boot signature to UART
Sending boot message. Please reboot the target...-
Sending boot image header (512 bytes)...
25 % [.... ]
Done
Sending boot image data (500964 bytes)...
0 % [......................................................................]
1 % [......................................................................]
3 % [......................................................................]
5 % [......................................................................]
7 % [......................................................................]
8 % [......................................................................]
10 % [......................................................................]
12 % [......................................................................]
14 % [......................................................................]
16 % [......................................................................]
17 % [......................................................................]
19 % [......................................................................]
21 % [......................................................................]
23 % [......................................................................]
25 % [......................................................................]
26 % [......................................................................]
28 % [......................................................................]
30 % [......................................................................]
32 % [......................................................................]
34 % [......................................................................]
35 % [......................................................................]
37 % [......................................................................]
39 % [......................................................................]
41 % [......................................................................]
42 % [......................................................................]
44 % [......................................................................]
46 % [......................................................................]
48 % [......................................................................]
50 % [......................................................................]
51 % [......................................................................]
53 % [......................................................................]
55 % [......................................................................]
57 % [......................................................................]
59 % [......................................................................]
60 % [......................................................................]
62 % [......................................................................]
64 % [......................................................................]
66 % [......................................................................]
67 % [......................................................................]
69 % [......................................................................]
71 % [......................................................................]
73 % [......................................................................]
75 % [......................................................................]
76 % [......................................................................]
78 % [......................................................................]
80 % [......................................................................]
82 % [......................................................................]
84 % [......................................................................]
85 % [......................................................................]
87 % [......................................................................]
89 % [......................................................................]
91 % [......................................................................]
93 % [......................................................................]
94 % [......................................................................]
96 % [......................................................................]
98 % [................................................................ ]
Done
Finishing transfer
[Type Ctrl-\ + c to quit]
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:38:05 -0700)
Netgear Stora MS2110
SoC: Kirkwood 88F6281_A1
DRAM: 128 MiB
WARNING: Caches not enabled
NAND: 256 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: egiga0
PHY reset timed out
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
Netgear Stora> printenv
arcNumber=2743
baudrate=115200
bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset
bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm$load_uimage_addr; fi; fi
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootdelay=10
bootdev=usb
console=console=ttyS0,115200
device=0:1
devices=usb ide
disks=0 1 2 3
dtb_file=/boot/dts/kirkwood-netgear_stora_ms2000
ethact=egiga0
ethaddr=52:3b:20:9c:11:51
if_netconsole=ping $serverip
ipaddr=192.168.0.231
led_error=orange blinking
led_exit=green off
led_init=green blinking
load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file
load_dtb_addr=0x1c00000
load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd
load_initrd_addr=0x1100000
load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage
load_uimage_addr=0x800000
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1m(uboot),4m@1m(kernel),251m@5m(rootfs) rw
partition=nand0,2
preboot_nc=run if_netconsole start_netconsole
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done
serverip=192.168.0.220
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
uenv_addr=0x810000
uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize
uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done;
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi
usb_ready_retry=15
Environment size: 2905/131068 bytes
Netgear Stora> usb reset
resetting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices...
Use USB retry period from the environment: 15 second(s)
1 Storage Device(s) found
Netgear Stora> setenv dtb_file '/boot/dts/kirkwood-netgear_stora_ms2000.dtb'
Netgear Stora> setenv custom_params 'earlyprintk=serial'
Netgear Stora> boot
Reset IDE: ide_preinit failed
Partition Map for USB device 0 -- Partition Type: DOS
Part Start Sector Num Sectors UUID Type
1 2048 60536833 e50dcb51-01 83
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **
no IDE devices available
running scan_disk ...
Scan device usb
device usb 0:1
1 bytes read in 691 ms (0 Bytes/s)
Found bootable drive on usb 0
loading uImage ...
6223944 bytes read in 882 ms (6.7 MiB/s)
loading uInitrd ...
5791271 bytes read in 777 ms (7.1 MiB/s)
loading DTB /boot/dts/kirkwood-netgear_stora_ms2000.dtb ...
11715 bytes read in 2906 ms (3.9 KiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-6.5.7-kirkwood-tld-1
Created: 2023-10-31 22:53:22 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 6223880 Bytes = 5.9 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-6.5.7-kirkwood-tld-1
Created: 2023-10-31 22:53:55 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5791207 Bytes = 5.5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
Booting using the fdt blob at 0x1c00000
Loading Kernel Image ... OK
Loading Ramdisk to 03a7a000, end 03fffde7 ... OK
Loading Device Tree to 03a74000, end 03a79dc2 ... OK
Starting kernel ...
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE
U-Boot 1.1.4 (Sep 4 2009 - 09:36:11) Marvell version: 3.4.14
...
Netgear Stora> usb reset
resetting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices...
Use USB retry period from the environment: 15 second(s)
1 Storage Device(s) found
Netgear Stora> setenv dtb_file '/boot/dts/kirkwood-netgear_stora_ms2000.dtb'
Netgear Stora> setenv custom_params 'earlyprintk=serial'
Netgear Stora> printenv
arcNumber=2743
baudrate=115200
bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset
bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm$load_uimage_addr; fi; fi
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootdelay=10
bootdev=usb
console=console=ttyS0,115200
custom_params=earlyprintk=serial
device=0:1
devices=usb ide
disks=0 1 2 3
dtb_file=/boot/dts/kirkwood-netgear_stora_ms2000.dtb
ethact=egiga0
ethaddr=52:3b:20:9c:11:51
if_netconsole=ping $serverip
ipaddr=192.168.0.231
led_error=orange blinking
led_exit=green off
led_init=green blinking
load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file
load_dtb_addr=0x1c00000
load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd
load_initrd_addr=0x1100000
load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage
load_uimage_addr=0x800000
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1m(uboot),4m@1m(kernel),251m@5m(rootfs) rw
partition=nand0,2
preboot_nc=run if_netconsole start_netconsole
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done
serverip=192.168.0.220
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
uenv_addr=0x810000
uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize
uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done;
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi
usb_ready_retry=15
Environment size: 2944/131068 bytes
Netgear Stora> boot
Reset IDE: ide_preinit failed
Partition Map for USB device 0 -- Partition Type: DOS
Part Start Sector Num Sectors UUID Type
1 2048 60536833 e50dcb51-01 83
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **
no IDE devices available
running scan_disk ...
Scan device usb
device usb 0:1
1 bytes read in 692 ms (0 Bytes/s)
Found bootable drive on usb 0
loading uImage ...
6223944 bytes read in 882 ms (6.7 MiB/s)
loading uInitrd ...
5791271 bytes read in 777 ms (7.1 MiB/s)
loading DTB /boot/dts/kirkwood-netgear_stora_ms2000.dtb ...
11715 bytes read in 2906 ms (3.9 KiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-6.5.7-kirkwood-tld-1
Created: 2023-10-31 22:53:22 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 6223880 Bytes = 5.9 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-6.5.7-kirkwood-tld-1
Created: 2023-10-31 22:53:55 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5791207 Bytes = 5.5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
Booting using the fdt blob at 0x1c00000
Loading Kernel Image ... OK
Loading Ramdisk to 03a7a000, end 03fffde7 ... OK
Loading Device Tree to 03a74000, end 03a79dc2 ... OK
Starting kernel ...
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 6.5.7-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #2 PREEMPT Wed Oct 18 21:14:11 PDT 2023
[ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: NETGEAR MS2000 / MS2110 aka Stora
[ 0.000000][ T0] printk: bootconsole [earlycon0] enabled
[ 0.000000][ T0] Memory policy: Data cache writeback
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:1m(uboot),4m@1m(kernel),251m@5m(rootfs) rw earlyprintk=serial
[ 0.000000][ T0] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000][ T0] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 102520K/131072K available (12288K kernel code, 1755K rwdata, 5416K rodata, 1024K init, 301K bss, 28552K reserved, 0K cma-reserved)
[ 0.000000][ T0] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000][ T0] trace event string verifier disabled
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000002][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.008626][ T0] Switching to timer-based delay loop, resolution 5ns
[ 0.016003][ T0] Console: colour dummy device 80x30
[ 0.021326][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000)
[ 0.032692][ T0] CPU: Testing write buffer coherency: ok
[ 0.038481][ T0] pid_max: default: 32768 minimum: 301
[ 0.054463][ T0] LSM: initializing lsm=capability,integrity
[ 0.063318][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.071470][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.095425][ T1] RCU Tasks: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[ 0.103785][ T1] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[ 0.112814][ T1] Setting up static identity map for 0x100000 - 0x100058
[ 0.120257][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[ 0.126731][ T1] rcu: Hierarchical SRCU implementation.
[ 0.132385][ T1] rcu: Max phase no-delay instances is 1000.
[ 0.142035][ T1] devtmpfs: initialized
[ 0.158917][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.169664][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.180711][ T1] prandom: seed boundary self test passed
[ 0.191505][ T1] prandom: 100 self tests passed
[ 0.196352][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.207108][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.215850][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.230114][ T1] audit: initializing netlink subsys (disabled)
[ 0.239080][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.239291][ T19] audit: type=2000 audit(0.220:1): state=initialized audit_enabled=0 res=1
[ 0.254623][ T1] cpuidle: using governor ladder
[ 0.259614][ T1] cpuidle: using governor menu
[ 0.265137][ T1] Feroceon L2: Enabling L2
[ 0.269600][ T1] Feroceon L2: Cache support initialised.
[ 0.288204][ T1] No ATAGs?
[ 0.658646][ T1] raid6: int32x8 gen() 91 MB/s
[ 0.998640][ T1] raid6: int32x4 gen() 88 MB/s
[ 1.338679][ T1] raid6: int32x2 gen() 113 MB/s
[ 1.678641][ T1] raid6: int32x1 gen() 82 MB/s
[ 1.683646][ T1] raid6: using algorithm int32x2 gen() 113 MB/s
[ 2.038646][ T1] raid6: .... xor() 72 MB/s, rmw enabled
[ 2.044175][ T1] raid6: using intx1 recovery algorithm
[ 2.060715][ T1] SCSI subsystem initialized
[ 2.079330][ T1] usbcore: registered new interface driver usbfs
[ 2.085673][ T1] usbcore: registered new interface driver hub
[ 2.098730][ T1] usbcore: registered new device driver usb
[ 2.104943][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 2.128644][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 2.138574][ T1] PTP clock support registered
[ 2.162038][ T1] vgaarb: loaded
[ 2.166515][ T1] clocksource: Switched to clocksource orion_clocksource
[ 2.207677][ T1] VFS: Disk quotas dquot_6.6.0
[ 2.212880][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.264333][ T1] NET: Registered PF_INET protocol family
[ 2.276909][ T1] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 2.298021][ T1] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 2.316822][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 2.325350][ T1] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 2.356567][ T1] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 2.364390][ T1] TCP: Hash tables configured (established 1024 bind 1024)
[ 2.387443][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 2.395705][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 2.416573][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 2.425353][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 2.447861][ T1] RPC: Registered named UNIX socket transport module.
[ 2.454529][ T1] RPC: Registered udp transport module.
[ 2.476541][ T1] RPC: Registered tcp transport module.
[ 2.481980][ T1] RPC: Registered tcp-with-tls transport module.
[ 2.496538][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.503739][ T1] PCI: CLS 0 bytes, default 32
[ 2.527129][ T10] Trying to unpack rootfs image as initramfs...
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE
U-Boot 1.1.4 (Sep 4 2009 - 09:36:11) Marvell version: 3.4.14
|
Re: Netgear Stora MS2000 - Detecting USB drives via latest uboot is inconsistent September 20, 2024 02:02PM |
Admin Registered: 13 years ago Posts: 18,898 |
cd /media/sdb1/boot echo "dtb_file=/boot/dts/kirkwood-netgear_stora_ms2000.dtb" > uEnv.txt sync
|
Re: Netgear Stora MS2000 - Detecting USB drives via latest uboot is inconsistent September 23, 2024 03:33PM |
Registered: 25 days ago Posts: 4 |
simon@X220:~$ sudo kwboot -t -B 115200 /dev/ttyUSB0 -b /home/simon/Downloads/uboot.2017.07-tld-1.netgear_ms2110.bodhi/uboot.2017.07-tld-1.netgear_ms2110.mtd0.kwb -p
kwboot version 2024.01
Detected kwbimage v0 with NAND boot signature
Patching image boot signature to UART
Sending boot message. Please reboot the target...-
Sending boot image header (512 bytes)...
25 % [.... ]
Done
Sending boot image data (500964 bytes)...
0 % [......................................................................]
1 % [......................................................................]
3 % [......................................................................]
5 % [......................................................................]
7 % [......................................................................]
8 % [......................................................................]
10 % [......................................................................]
12 % [......................................................................]
14 % [......................................................................]
16 % [......................................................................]
17 % [......................................................................]
19 % [......................................................................]
21 % [......................................................................]
23 % [......................................................................]
25 % [......................................................................]
26 % [......................................................................]
28 % [......................................................................]
30 % [......................................................................]
32 % [......................................................................]
34 % [......................................................................]
35 % [......................................................................]
37 % [......................................................................]
39 % [......................................................................]
41 % [......................................................................]
42 % [......................................................................]
44 % [......................................................................]
46 % [......................................................................]
48 % [......................................................................]
50 % [......................................................................]
51 % [......................................................................]
53 % [......................................................................]
55 % [......................................................................]
57 % [......................................................................]
59 % [......................................................................]
60 % [......................................................................]
62 % [......................................................................]
64 % [......................................................................]
66 % [......................................................................]
67 % [......................................................................]
69 % [......................................................................]
71 % [......................................................................]
73 % [......................................................................]
75 % [......................................................................]
76 % [......................................................................]
78 % [......................................................................]
80 % [......................................................................]
82 % [......................................................................]
84 % [......................................................................]
85 % [......................................................................]
87 % [......................................................................]
89 % [......................................................................]
91 % [......................................................................]
93 % [......................................................................]
94 % [......................................................................]
96 % [......................................................................]
98 % [................................................................ ]
Done
Finishing transfer
[Type Ctrl-\ + c to quit]
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:38:05 -0700)
Netgear Stora MS2110
SoC: Kirkwood 88F6281_A1
DRAM: 128 MiB
WARNING: Caches not enabled
NAND: 256 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: egiga0
PHY reset timed out
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
Netgear Stora>
Netgear Stora>
Netgear Stora> setenv dtb_file '/boot/dts/kirkwood-netgear_stora_ms2000.dtb'
Netgear Stora> usb reset
resetting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices...
Use USB retry period from the environment: 15 second(s)
1 Storage Device(s) found
Netgear Stora>
resetting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices...
Use USB retry period from the environment: 15 second(s)
1 Storage Device(s) found
Netgear Stora> boot
Reset IDE: ide_preinit failed
Partition Map for USB device 0 -- Partition Type: DOS
Part Start Sector Num Sectors UUID Type
1 2048 60536833 e50dcb51-01 83
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **
no IDE devices available
running scan_disk ...
Scan device usb
device usb 0:1
1 bytes read in 692 ms (0 Bytes/s)
Found bootable drive on usb 0
loading uImage ...
6223944 bytes read in 882 ms (6.7 MiB/s)
loading uInitrd ...
5791271 bytes read in 777 ms (7.1 MiB/s)
loading DTB /boot/dts/kirkwood-netgear_stora_ms2000.dtb ...
11715 bytes read in 2906 ms (3.9 KiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-6.5.7-kirkwood-tld-1
Created: 2023-10-31 22:53:22 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 6223880 Bytes = 5.9 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-6.5.7-kirkwood-tld-1
Created: 2023-10-31 22:53:55 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5791207 Bytes = 5.5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
Booting using the fdt blob at 0x1c00000
Loading Kernel Image ... OK
Loading Ramdisk to 03a7a000, end 03fffde7 ... OK
Loading Device Tree to 03a74000, end 03a79dc2 ... OK
Starting kernel ...
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 6.5.7-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #2 PREEMPT Wed Oct 18 21:14:11 PDT 2023
[ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: NETGEAR MS2000 / MS2110 aka Stora
[ 0.000000][ T0] Memory policy: Data cache writeback
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:1m(uboot),4m@1m(kernel),251m@5m(rootfs) rw
[ 0.000000][ T0] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000][ T0] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 102520K/131072K available (12288K kernel code, 1755K rwdata, 5416K rodata, 1024K init, 301K bss, 28552K reserved, 0K cma-reserved)
[ 0.000000][ T0] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000][ T0] trace event string verifier disabled
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000002][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.000059][ T0] Switching to timer-based delay loop, resolution 5ns
[ 0.000793][ T0] Console: colour dummy device 80x30
[ 0.000881][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000)
[ 0.000920][ T0] CPU: Testing write buffer coherency: ok
[ 0.001086][ T0] pid_max: default: 32768 minimum: 301
[ 0.011724][ T0] LSM: initializing lsm=capability,integrity
[ 0.014629][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.014676][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.030204][ T1] RCU Tasks: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[ 0.030680][ T1] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[ 0.031300][ T1] Setting up static identity map for 0x100000 - 0x100058
[ 0.031715][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[ 0.032335][ T1] rcu: Hierarchical SRCU implementation.
[ 0.032357][ T1] rcu: Max phase no-delay instances is 1000.
[ 0.036000][ T1] devtmpfs: initialized
[ 0.048559][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.048616][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.052171][ T1] prandom: seed boundary self test passed
[ 0.057294][ T1] prandom: 100 self tests passed
[ 0.057313][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.062914][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.064091][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.070681][ T1] audit: initializing netlink subsys (disabled)
[ 0.073452][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.073662][ T19] audit: type=2000 audit(0.070:1): state=initialized audit_enabled=0 res=1
[ 0.073728][ T1] cpuidle: using governor ladder
[ 0.073831][ T1] cpuidle: using governor menu
[ 0.074651][ T1] Feroceon L2: Enabling L2
[ 0.074698][ T1] Feroceon L2: Cache support initialised.
[ 0.087694][ T1] No ATAGs?
[ 0.450079][ T1] raid6: int32x8 gen() 91 MB/s
[ 0.790075][ T1] raid6: int32x4 gen() 88 MB/s
[ 1.130114][ T1] raid6: int32x2 gen() 113 MB/s
[ 1.470075][ T1] raid6: int32x1 gen() 81 MB/s
[ 1.470092][ T1] raid6: using algorithm int32x2 gen() 113 MB/s
[ 1.810078][ T1] raid6: .... xor() 72 MB/s, rmw enabled
[ 1.810095][ T1] raid6: using intx1 recovery algorithm
[ 1.812176][ T1] SCSI subsystem initialized
[ 1.813161][ T1] usbcore: registered new interface driver usbfs
[ 1.813295][ T1] usbcore: registered new interface driver hub
[ 1.813421][ T1] usbcore: registered new device driver usb
[ 1.813854][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 1.813866][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.813906][ T1] PTP clock support registered
[ 1.817327][ T1] vgaarb: loaded
[ 1.818359][ T1] clocksource: Switched to clocksource orion_clocksource
[ 1.837999][ T1] VFS: Disk quotas dquot_6.6.0
[ 1.848590][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.879735][ T1] NET: Registered PF_INET protocol family
[ 1.880107][ T1] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 1.889894][ T1] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 1.890191][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 1.890228][ T1] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 1.890269][ T1] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 1.890309][ T1] TCP: Hash tables configured (established 1024 bind 1024)
[ 1.891163][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 1.891462][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 1.891506][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 1.892574][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 1.894025][ T1] RPC: Registered named UNIX socket transport module.
[ 1.894042][ T1] RPC: Registered udp transport module.
[ 1.894051][ T1] RPC: Registered tcp transport module.
[ 1.894058][ T1] RPC: Registered tcp-with-tls transport module.
[ 1.894066][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.894093][ T1] PCI: CLS 0 bytes, default 32
[ 1.897729][ T32] Trying to unpack rootfs image as initramfs...
[ 3.093236][ T32] Freeing initrd memory: 5656K
[ 4.300051][ T1] Initialise system trusted keyrings
[ 4.300167][ T1] Key type blacklist registered
[ 4.301929][ T1] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 4.302155][ T1] zbud: loaded
[ 4.325324][ T1] NFS: Registering the id_resolver key type
[ 4.325388][ T1] Key type id_resolver registered
[ 4.325401][ T1] Key type id_legacy registered
[ 4.325637][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 4.325665][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 4.327584][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 4.328787][ T1] fuse: init (API version 7.38)
[ 4.330542][ T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 4.331001][ T1] orangefs_init: module version upstream loaded
[ 4.331476][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled
[ 4.586057][ T1] xor: measuring software checksum speed
[ 4.596730][ T1] arm4regs : 927 MB/sec
[ 4.614456][ T1] 8regs : 556 MB/sec
[ 4.626946][ T1] 32regs : 789 MB/sec
[ 4.626958][ T1] xor: using function: arm4regs (927 MB/sec)
[ 4.626977][ T1] async_tx: api initialized (async)
[ 4.626997][ T1] Key type asymmetric registered
[ 4.627008][ T1] Asymmetric key parser 'x509' registered
[ 4.691081][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[ 4.691627][ T1] io scheduler bfq registered
[ 4.919986][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 4.922239][ T1] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 4.923984][ T1] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 4.925240][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges:
[ 4.925341][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000
[ 4.925396][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 4.925431][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 4.926517][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[ 4.926542][ T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 4.926566][ T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff])
[ 4.926587][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[ 4.926605][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 4.926746][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400
[ 4.929077][ T1] PCI: bus0: Fast back to back transfers disabled
[ 4.929115][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 4.929540][ T1] PCI: bus1: Fast back to back transfers enabled
[ 4.929568][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 4.929620][ T1] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 4.930909][ T1] mv_xor f1060800.xor: Marvell shared XOR driver
[ 4.991583][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 4.997409][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 5.061588][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 5.067814][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 5.071310][ T1] printk: console [ttyS0] disabled
[ 5.072139][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 28, base_baud = 12500000) is a 16550A
[ 5.072224][ T1] printk: console [ttyS0] enabled
[ 6.074786][ T1] loop: module loaded
[ 6.080076][ T1] sata_mv f1080000.sata: slots 32 ports 2
[ 6.091836][ T1] scsi host0: sata_mv
[ 6.097697][ T1] scsi host1: sata_mv
[ 6.102245][ T1] ata1: SATA max UDMA/133 irq 29
[ 6.107081][ T1] ata2: SATA max UDMA/133 irq 29
[ 6.113739][ T1] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xda
[ 6.120896][ T1] nand: Samsung NAND 256MiB 3,3V 8-bit
[ 6.126246][ T1] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 6.134616][ T1] Scanning device for bad blocks
[ 6.220375][ T1] Bad eraseblock 750 at 0x000005dc0000
[ 6.230646][ T1] Bad eraseblock 796 at 0x000006380000
[ 6.250761][ T1] Bad eraseblock 933 at 0x0000074a0000
[ 6.315780][ T1] Bad eraseblock 1487 at 0x00000b9e0000
[ 6.348982][ T1] Bad eraseblock 1744 at 0x00000da00000
[ 6.387186][ T1] 3 cmdlinepart partitions found on MTD device orion_nand
[ 6.394243][ T1] Creating 3 MTD partitions on "orion_nand":
[ 6.400169][ T1] 0x000000000000-0x000000100000 : "uboot"
[ 6.406874][ T1] 0x000000100000-0x000000500000 : "kernel"
[ 6.413575][ T1] 0x000000500000-0x000010000000 : "rootfs"
[ 6.422727][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 6.431405][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 6.441788][ T53] ata1: SATA link down (SStatus 0 SControl F300)
[ 6.453796][ T1] [Firmware Warn]: /ocp@f1000000/mdio-bus@72004/ethernet-phy@8: Whitelisted compatible string. Please remove
[ 6.493831][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 6.800115][ T55] ata2: SATA link down (SStatus 0 SControl F300)
[ 7.260030][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 52:3b:20:9c:11:51
[ 7.270375][ T1] orion-ehci f1050000.ehci: EHCI Host Controller
[ 7.276648][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 7.285414][ T1] orion-ehci f1050000.ehci: irq 32, io mem 0xf1050000
[ 7.318399][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 7.325635][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.05
[ 7.334695][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.342687][ T1] usb usb1: Product: EHCI Host Controller
[ 7.348304][ T1] usb usb1: Manufacturer: Linux 6.5.7-kirkwood-tld-1 ehci_hcd
[ 7.355679][ T1] usb usb1: SerialNumber: f1050000.ehci
[ 7.362419][ T1] hub 1-0:1.0: USB hub found
[ 7.366961][ T1] hub 1-0:1.0: 1 port detected
[ 7.372984][ T1] usbcore: registered new interface driver usb-storage
[ 7.380533][ T1] mousedev: PS/2 mouse device common for all mice
[ 7.658409][ T50] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 7.862920][ T50] usb 1-1: New USB device found, idVendor=0951, idProduct=1666, bcdDevice= 2.00
[ 7.871910][ T50] usb 1-1: New USB device strings: Mfr=2, Product=3, SerialNumber=4
[ 7.879841][ T50] usb 1-1: Product: DataTraveler 3.0
[ 7.885021][ T50] usb 1-1: Manufacturer: Kingston
[ 7.889959][ T50] usb 1-1: SerialNumber: E0D55EA5742A1691D87D07A6
[ 7.897604][ T50] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 7.905695][ T50] scsi host2: usb-storage 1-1:1.0
[ 8.408412][ T1] rtc-mv f1010300.rtc: internal RTC not ticking
[ 8.414954][ T1] i2c_dev: i2c /dev entries driver
[ 8.424627][ T1] rtc-pcf8563 0-0051: registered as rtc0
[ 8.431538][ T1] rtc-pcf8563 0-0051: setting system clock to 2024-09-23T19:14:04 UTC (1727118844)
[ 8.443481][ T1] device-mapper: uevent: version 1.0.3
[ 8.449661][ T1] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com
[ 8.459708][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 8.466988][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 8.474438][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 8.481931][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 8.492449][ T1] ledtrig-cpu: registered to indicate activity on CPUs
[ 8.499507][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 8.505961][ T1] drop_monitor: Initializing network drop monitor service
[ 8.514942][ T1] NET: Registered PF_INET6 protocol family
[ 8.523350][ T1] Segment Routing with IPv6
[ 8.527754][ T1] RPL Segment Routing with IPv6
[ 8.532717][ T1] In-situ OAM (IOAM) with IPv6
[ 8.537591][ T1] NET: Registered PF_PACKET protocol family
[ 8.543873][ T1] Key type dns_resolver registered
[ 8.572429][ T1] registered taskstats version 1
[ 8.577565][ T1] Loading compiled-in X.509 certificates
[ 8.610163][ T1] Key type .fscrypt registered
[ 8.614844][ T1] Key type fscrypt-provisioning registered
[ 8.628776][ T1] Key type big_key registered
[ 8.690389][ T1] Key type encrypted registered
[ 8.827541][ T107] "cryptomgr_test" (107) uses obsolete ecb(arc4) skcipher
[ 8.969775][ T18] scsi 2:0:0:0: Direct-Access Kingston DataTraveler 3.0 0000 PQ: 0 ANSI: 4
[ 8.990975][ T32] sd 2:0:0:0: [sda] 60538881 512-byte logical blocks: (31.0 GB/28.9 GiB)
[ 9.008965][ T32] sd 2:0:0:0: [sda] Write Protect is off
[ 9.018427][ T32] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 9.056851][ T32] sda: sda1
[ 9.069137][ T32] sd 2:0:0:0: [sda] Attached SCSI removable disk
[ 11.640406][ T1] clk: Disabling unused clocks
[ 11.649722][ T1] Freeing unused kernel image (initmem) memory: 1024K
[ 11.669442][ T1] Checked W+X mappings: passed, no W+X pages found
[ 11.675866][ T1] Run /init as init process
Loading, please wait...
Starting systemd-udevd version 252.17-1~deb12u1
[ 13.436319][ T150] usbcore: registered new interface driver uas
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.38.1
fsck: error 2 (No such file or directory) while executing fsck.ext4 for /dev/sda1
fsck exited with status code 8
done.
Warning: File system check failed but did not detect errors
[ 29.340396][ T177] EXT4-fs (sda1): mounted filesystem 7a4183bd-8d84-4bf7-951d-a7312419fcde r/w with ordered data mode. Quota mode: none.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 3.06 booting
INIT: No inittab.d directory found
Using makefile-style concurrent boot in runlevel S.
Setting hostname to 'debian'...done.
Starting hotplug events dispatcher: systemd-udevd.
Synthesizing the initial hotplug events (subsystems)...done.
Synthesizing the initial hotplug events (devices)...done.
Waiting for /dev to be fully populated...[ 33.015313][ T356] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 33.412975][ T356] lm75 0-0048: supply vs not found, using dummy regulator
[ 33.549798][ T356] hwmon hwmon0: temp1_input not attached to any thermal zone
[ 33.565334][ T368] orion_wdt: Initial timeout 21 sec
[ 33.666481][ T356] lm75 0-0048: hwmon0: sensor 'lm75'
[ 34.368497][ C0] random: crng init done
[ 34.410404][ T358] marvell-cesa f1030000.crypto: CESA device successfully registered
[ 34.518709][ T356] sd 2:0:0:0: Attached scsi generic sg0 type 0
done.
Activating swap:.
[ 36.896184][ T513] EXT4-fs (sda1): re-mounted 7a4183bd-8d84-4bf7-951d-a7312419fcde ro. Quota mode: none.
Will now check root file system:[/sbin/fsck.ext4 (1) -- /] fsck.ext4 -y -C0 /dev/sda1
e2fsck 1.47.0 (5-Feb-2023)
rootfs: clean, 20038/1892352 files, 407779/7567104 blocks
.
[ 37.298927][ T520] EXT4-fs (sda1): re-mounted 7a4183bd-8d84-4bf7-951d-a7312419fcde r/w. Quota mode: none.
Will now check all file systems.
Checking all file systems.
LABEL=rootfs is mounted
Done checking file systems.
Log is being saved in /var/log/fsck/checkfs if that location is writable.
Cleaning up temporary files...Cleaning /tmp...done.
/tmp.
Will now mount local filesystems:.
Will now activate swapfile swap, if any:done.
Checking minimum space in /tmp...done.
Cleaning up temporary files....
Starting Setting kernel variables: sysctl.
Initializing random number generator...done.
Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.3-P1
Copyright 2004-2022 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/52:3b:20:9c:11:51
Sending on LPF/eth0/52:3b:20:9c:11:51
Sending on Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
[ 43.669933][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
DHCPOFFER of 10.1.1.227 from 10.1.1.1
DHCPREQUEST for 10.1.1.227 on eth0 to 255.255.255.255 port 67
DHCPACK of 10.1.1.227 from 10.1.1.1
bound to 10.1.1.227 -- renewal in 3544 seconds.
done.
Starting RPC port mapper daemon: rpcbind.
Starting NFS common utilities: statd idmapd.
Cleaning up temporary files....
INIT: Entering runlevel: 2
Using makefile-style concurrent boot in runlevel 2.
Not starting NFS kernel daemon: no exports ... (warning).
Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1029 (syslogd)
.
Starting system message bus: dbus.
Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
Starting NTP server: ntpd2024-09-23T12:14:44 ntpd[1062]: INIT: ntpd ntpsec-1.2.2: Starting
2024-09-23T12:14:44 ntpd[1062]: INIT: Command line: /usr/sbin/ntpd -p /var/run/ntpd.pid -g -u 104:106
.
Starting NTP server: ntpd.
Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1038 (klogd)
.
Starting OpenBSD Secure Shell server: sshdsshd: no hostkeys available -- exiting.
failed!
Running local boot scripts (/etc/rc.local)
ssh-keygen: generating new host keys: RSA
ECDSA
ED25519
Starting OpenBSD Secure Shell server: sshd
.
.
Debian GNU/Linux 12 debian ttyS0
debian login:
|
Re: Netgear Stora MS2000 - Detecting USB drives via latest uboot is inconsistent September 23, 2024 04:40PM |
Admin Registered: 13 years ago Posts: 18,898 |