(Solved) After Debian install, it boots back to PogoPlug, E02 December 12, 2013 03:09AM |
Registered: 10 years ago Posts: 162 |
Quote
U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02
arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1
GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/rescueme" from usb device 0:1 (usbda1)
** File not found /rescueme
reading /rescueme.txt
** Unable to read "/rescueme.txt" from usb 0:1 **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 728
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
** File not found /boot/uImage
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
** File not found /boot/uImage
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
** File not found /boot/uInitrd
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: ......... done.
### JFFS2 load complete: 524288 bytes loaded to 0x800000
## Starting application at 0x00800200 ...
Re: After Debian install, it boots back to PogoPlug, E02 December 12, 2013 03:17AM |
Admin Registered: 13 years ago Posts: 18,644 |
Re: After Debian install, it boots back to PogoPlug, E02 December 12, 2013 03:21AM |
Registered: 10 years ago Posts: 162 |
Re: After Debian install, it boots back to PogoPlug, E02 December 12, 2013 03:44AM |
Admin Registered: 13 years ago Posts: 18,644 |
Re: After Debian install, it boots back to PogoPlug, E02 December 12, 2013 04:02AM |
Registered: 10 years ago Posts: 162 |
Quote
Disk /dev/sda: 20.0 GB, 20003880960 bytes
255 heads, 63 sectors/track, 2432 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 * 1 188 1510078+ 83 Linux
/dev/sda2 189 221 265072+ 82 Linux swap
Re: After Debian install, it boots back to PogoPlug, E02 December 12, 2013 12:23PM |
Admin Registered: 13 years ago Posts: 18,644 |
Re: After Debian install, it boots back to PogoPlug, E02 December 12, 2013 10:46PM |
Registered: 10 years ago Posts: 162 |
Quote
U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02
arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1
GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/rescueme" from usb device 0:1 (usbda1)
** File not found /rescueme
reading /rescueme.txt
** Unable to read "/rescueme.txt" from usb 0:1 **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 728
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
stopping USB..
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1 bytes read
Found bootable drive on usb 0:1
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1435696 bytes read
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
4535463 bytes read
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-2.6.32-5-kirkwood
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1435632 Bytes = 1.4 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-2.6.32-5-kirkwood
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 4535399 Bytes = 4.3 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Re: After Debian install, it boots back to PogoPlug, E02 December 13, 2013 12:22AM |
Registered: 10 years ago Posts: 162 |
Re: After Debian install, it boots back to PogoPlug, E02 December 13, 2013 01:14AM |
Registered: 10 years ago Posts: 162 |
Re: After Debian install, it boots back to PogoPlug, E02 December 13, 2013 02:43AM |
Admin Registered: 13 years ago Posts: 18,644 |
Re: After Debian install, it boots back to PogoPlug, E02 December 13, 2013 03:24AM |
Registered: 10 years ago Posts: 162 |
Quote
debconf: unable to initialize frontend: Dialog
debconf: (No usable dialog-like program is installed, so the dialog based frontend cannot be used. at /usr/share/perl5/Debconf/FrontEnd/Dialog.pm line 76.)
debconf: falling back to frontend: Readline
Setting up samba (2:3.6.6-6+deb7u2) ...
debconf: unable to initialize frontend: Dialog
debconf: (No usable dialog-like program is installed, so the dialog based frontend cannot be used. at /usr/share/perl5/Debconf/FrontEnd/Dialog.pm line 76.)
debconf: falling back to frontend: Readline
-bash: debconf:: command not found
root@debian:/etc/samba# debconf: (No usable dialog-like program is installed, so the dialog based frontend cannot be used. at /usr/share/perl5/Debconf/FrontEnd/Dialog.pm line 76.)
debconf: falling back to frontend: Readline
Re: After Debian install, it boots back to PogoPlug, E02 December 13, 2013 03:46AM |
Admin Registered: 13 years ago Posts: 18,644 |
apt-get install dialog
Re: After Debian install, it boots back to PogoPlug, E02 December 13, 2013 03:55AM |
Registered: 10 years ago Posts: 162 |
Re: After Debian install, it boots back to PogoPlug, E02 December 13, 2013 11:14AM |
Registered: 10 years ago Posts: 169 |
Pogoplug:/tmp/sda/boot$ ls -l -rw-r--r-- 1 root root 1006219 Sep 25 2013 System.map-2.6.32-5-kirkwood -rw-r--r-- 1 root root 84134 Sep 25 2013 config-2.6.32-5-kirkwood -rw-r--r-- 1 root root 4535174 Jan 1 00:17 initrd.img-2.6.32-5-kirkwood -rw-r--r-- 1 root root 1435632 Sep 25 2013 vmlinuz-2.6.32-5-kirkwood
Re: After Debian install, it boots back to PogoPlug, E02 December 13, 2013 12:00PM |
Registered: 10 years ago Posts: 162 |
Quote
mkdir /tmp/debian
mount /dev/sda1 /tmp/debian
#/tmp/debian/usr/sbin/chroot /tmp/debian /bin/bash
export PATH=$PATH:/usr/sbin:/sbin
cd /tmp/debian/usr/bin
./mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-2.6.32-5-kirkwood -d ../../boot/vmlinuz-2.6.32-5-kirkwood ../../boot/uImage
./mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-2.6.32-5-kirkwood -d ../../boot/initrd.img-2.6.32-5-kirkwood ../../boot/uInitrd
cd /tmp
sync
umount /dev/sda1
reboot -f
Re: After Debian install, it boots back to PogoPlug, E02 December 13, 2013 01:16PM |
Registered: 10 years ago Posts: 169 |
root@Pogoplug:/# /usr/bin/mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-2.6.32-5-kirkwood -d /boot/vmlinuz-2.6.32-5-kirkwood /boot/uImage Image Name: Linux-2.6.32-5-kirkwood Created: Sat Jan 1 00:04:52 2000 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1435632 Bytes = 1401.98 kB = 1.37 MB Load Address: 0x00008000 Entry Point: 0x00008000 root@Pogoplug:/# /usr/bin/mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-2.6.32-5-kirkwood -d /boot/initrd.img-2.6.32-5-kirkwood /boot/uInitrd Image Name: initramfs-2.6.32-5-kirkwood Created: Sat Jan 1 00:05:35 2000 Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 4535174 Bytes = 4428.88 kB = 4.33 MB Load Address: 0x00000000 Entry Point: 0x00000000 root@Pogoplug:/# root@Pogoplug:/tmp# sync bash: /bin/sync: Input/output error root@Pogoplug:/tmp# umount /dev/sda1 warning: can't open /etc/mtab: No such file or directory umount: /dev/sda1: not found root@Pogoplug:/tmp# reboot -f
Re: After Debian install, it boots back to PogoPlug, E02 December 13, 2013 01:43PM |
Registered: 10 years ago Posts: 162 |