Dockstar booting probllem December 03, 2015 04:12PM |
Registered: 9 years ago Posts: 9 |
U-Boot 2015.10-tld-1 (Nov 06 2015 - 15:56:21 -0800) Seagate FreeAgent DockStar gcc (Debian 4.9.2-10) 4.9.2 GNU ld (GNU Binutils for Debian) 2.25 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Unknown command 'ide' - try 'help' Unknown command 'mmc' - try 'help' Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 63 22585281 23a6c3e4-01 83 Boot 2 22585344 4192256 23a6c3e4-02 82 3 26777600 -414715904 23a6c3e4-03 05 Extd 5 26779648 -414717952 23a6c3e4-05 83 loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** Unknown command 'ide' - try 'help' Unknown command 'mmc' - try 'help' running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 336 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 3147200 bytes read in 413 ms (7.3 MiB/s) loading uInitrd ... 5589530 bytes read in 713 ms (7.5 MiB/s) loading DTB /boot/dts/kirkwood-dockstar.dtb ... 10398 bytes read in 610 ms (16.6 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.2.0-kirkwood-tld-1 Created: 1970-01-01 0:15:29 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3147136 Bytes = 3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.2.0-kirkwood-tld-1 Created: 1970-01-01 0:17:12 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 5589466 Bytes = 5.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Starting kernel ...At this point there's a solid orange LED for 4s or so and then solid green light. With both kernels USB hard drive stops spinning once the kernel is loaded.. With old kernel a short time after the green light the kernel mounts the hdd again, and init commences indicated by hard drive access. boot finishes successfully as I can log in.
DockStar> print print arcNumber=2998 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=mw 0x800000 0 1; run load_uimage; if run load_initrd; then if run load_dtb; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 0x1100000; fi; else if run load_dtb; then bootm 0x800000 - 0x1c00000; else bootm 0x800000; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-dockstar.dtb ethact=egiga0 ethaddr=00:10:75:DD:DD:DD if_netconsole=ping $serverip ipaddr=192.168.1.100 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; ext2load $bootdev $device 0x1c00000 $dtb_file load_initrd=echo loading uInitrd ...; ext2load $bootdev $device 0x1100000 /boot/uInitrd load_uimage=echo loading uImage ...; ext2load $bootdev $device 0x800000 /boot/uImage mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) nc_ready=1 ncip=192.168.1.53 partition=nand0,2 preboot=run preboot_nc preboot_nc=setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if ext2load $dev $disknum:1 0x800000 /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.1.53 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=nc stdin=nc stdout=nc uenv_import=echo importing envs ...; env import -t 0x810000 uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x810000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15 Environment size: 2847/131068 bytes
Re: Dockstar booting probllem December 03, 2015 06:20PM |
Admin Registered: 13 years ago Posts: 18,858 |
Re: Dockstar booting probllem December 04, 2015 06:56AM |
Registered: 9 years ago Posts: 9 |
Re: Dockstar booting probllem December 04, 2015 03:12PM |
Admin Registered: 13 years ago Posts: 18,858 |
Quote
r1. There must be only one partition among all partitions from all drives that contains the kernel files. The 2 kernel files are /boot/uImage and /boot/uInitrd.
r2. The partition that contains the 2 kernel files must be partition 1 in a disk drive
r3. The partition that contains the rootfs must be labeled rootfs
r4. The rootfs partition is recommended to be type Ext3 (this is not a hard requirement, ext4 should boot OK, but Ext3 will ensure no problem).
Quote
4a. Boot with DTB file (standard way to boot FDT kernel). Recommended.
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-4.2.0-kirkwood-tld-1 -d vmlinuz-4.2.0-kirkwood-tld-1 uImage
Re: Dockstar booting probllem December 04, 2015 03:38PM |
Registered: 9 years ago Posts: 9 |
Re: Dockstar booting probllem December 04, 2015 03:53PM |
Admin Registered: 13 years ago Posts: 18,858 |
Re: Dockstar booting probllem December 04, 2015 05:08PM |
Registered: 9 years ago Posts: 9 |
Re: Dockstar booting probllem December 04, 2015 10:07PM |
Admin Registered: 13 years ago Posts: 18,858 |