dummy64
NSA325 - stock u-boot problem booting with Linux Kernel 4.13.5 October 12, 2017 11:39AM |
cd /boot tar -xjf linux-4.13.5-kirkwood-tld-1-bodhi.tar.bz2 tar -xf linux-dtb-4.13.5-kirkwood-tld-1.tar cd /boot apt-get remove flash-kernel dpkg -i linux-image-4.13.5-kirkwood-tld-1_1.0_armel.deb cp -a zImage-4.13.5-kirkwood-tld-1 zImage.fdt cat dts/kirkwood-nsa325.dtb >> zImage.fdt mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-4.13.5-kirkwood-tld-1 -d zImage.fdt uImage mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-4.13.5-kirkwood-tld-1 -d initrd.img-4.13.5-kirkwood-tld-1 uInitrd
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** MARVELL BOARD: DB-88F6282A-BP LE U-Boot 1.1.4 (Jul 18 2013 - 10:47:29) Marvell version: 3.5.9 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00 Soc: 88F6282 A1CPU running @ 1600Mhz L2 running @ 533Mhz SysClock = 533Mhz , TClock = 200Mhz DRAM (DDR3) CAS Latency = 7 tRP = 8 tRAS = 24 tRCD=8 DRAM CS[0] base 0x00000000 size 512MB DRAM Total size 512MB 16bit width Addresses 10M - 0M are saved for the U-Boot usage. Mem malloc Initialization (10M - 7M): Done NAND:128 MB Flash: 0 kB CPU : Marvell Feroceon (Rev 1) Kernel address is 0x4640000. Streaming disabled Write allocate disabled USB 0: host mode [BlueDBG] reseting SoC Pex[0] 0 ... PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 [BlueDBG] reseting SoC Pex[1] 0 ... [BlueDBG] reseting SoC Pex[1] 1 ... [BlueDBG] reseting SoC Pex[1] 2 ... [BlueDBG] reseting SoC Pex[1] 3 ... [BlueDBG] reseting SoC Pex[1] 4 ... [BlueDBG] reseting SoC Pex[1] 5 ... [BlueDBG] reseting SoC Pex[1] 6 ... [BlueDBG] reseting SoC Pex[1] 7 ... [BlueDBG] reseting SoC Pex[1] 8 ... [BlueDBG] reseting SoC Pex[1] 9 ... [BlueDBG] reseting SoC Pex[1] 10 ... PEX 1: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 (Re)start USB... USB: scanning bus for devices... 3 USB Device(s) found Waiting for storage device(s) to settle before scanning... 1 Storage Device(s) found .... 8386386 bytes read ## Booting image at 02000000 ... Image Name: Linux-4.13.5-kirkwood-tld-1 Created: 2017-10-12 16:12:18 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3862548 Bytes = 3.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 01100000 ... Image Name: initramfs-4.13.5-kirkwood-tld-1 Created: 2017-10-12 16:12:32 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 8386322 Bytes = 8 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. _
drwxrwxrwx 4 root root 1.0K Oct 12 16:12 . drwxr-xr-x 6 root root 4.0K Oct 12 15:13 .. -rw-r--r-- 1 root root 152K Oct 7 08:53 config-4.13.5-kirkwood-tld-1 -rw-r--r-- 1 root root 143K Oct 21 2016 config-4.8.3-kirkwood-tld-1 drwxr-xr-x 2 root root 5.0K Sep 20 08:13 dts -rw-r--r-- 1 root root 8.0M Oct 12 14:24 initrd.img-4.13.5-kirkwood-tld-1 -rw-r--r-- 1 root root 8.2M Oct 9 22:49 initrd.img-4.8.3-kirkwood-tld-1 -rw-r--r-- 1 root root 141K Dec 8 2016 linux-4.8.3-kirkwood-tld-1.patch drwx------ 2 root root 1.0K Dec 8 2016 lost+found -rw------- 1 root root 2.5M Oct 7 11:26 System.map-4.13.5-kirkwood-tld-1 -rw------- 1 root root 2.3M Oct 21 2016 System.map-4.8.3-kirkwood-tld-1 -rw-r--r-- 1 root root 3.7M Oct 12 16:12 uImage -rw-r--r-- 1 root root 8.0M Oct 12 16:12 uInitrd -rw------- 1 root root 3.7M Oct 7 11:26 vmlinuz-4.13.5-kirkwood-tld-1 -rw------- 1 root root 3.1M Oct 21 2016 vmlinuz-4.8.3-kirkwood-tld-1 -rwxr-xr-x 1 root root 3.7M Oct 7 06:56 zImage-4.13.5-kirkwood-tld-1 -rwxr-xr-x 1 root root 3.1M Dec 8 2016 zImage-4.8.3-kirkwood-tld-1 -rwxr-xr-x 1 root root 3.7M Oct 12 16:11 zImage.fdt # file uImage uImage: u-boot legacy uImage, Linux-4.13.5-kirkwood-tld-1, Linux/ARM, OS Kernel Image (Not compressed), 3862548 bytes, Thu Oct 12 16:12:18 2017, Load Address: 0x00008000, Entry Point: 0x00008000, Header CRC: 0x3E922991, Data CRC: 0x0313BB48 # file uInitrd uInitrd: u-boot legacy uImage, initramfs-4.13.5-kirkwood-tld-1, Linux/ARM, RAMDisk Image (gzip), 8386322 bytes, Thu Oct 12 16:12:32 2017, Load Address: 0x00000000, Entry Point: 0x00000000, Header CRC: 0x8F561567, Data CRC: 0x55FE9383
Re: NSA325 - Problem booting with Linux Kernel 4.13.5 October 12, 2017 03:50PM |
Admin Registered: 13 years ago Posts: 18,613 |
printenv
dummy64
Re: NSA325 - Problem booting with Linux Kernel 4.13.5 October 12, 2017 05:44PM |
Marvell>> printenv bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init bootdelay=2 baudrate=115200 loads_echo=0 ipaddr=10.4.52.165 serverip=10.4.52.7 rootpath=/srv/ubuntu netmask=255.255.255.0 nandEcc=1bit MODEL_ID=AE03 PRODUCT_NAME=NSA-325v2 FEATURE_BIT=00 CONTRY_TYPE=FF VENDOR_NAME=MitraStar Technology Corp. run_diag=yes console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root) ethprime=egiga0 bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; lcd0_enable=0 lcd0_params=640x480-16@60 ethaddr=00:50:43:00:02:02 ethmtu=1500 mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no image_multi=yes ethact=egiga0 arcNumber=4495 bootargs_stock=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init bootargs_linux=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=LABEL=rootfs loglevel=8 bootcmd_linux=setenv bootargs $(bootargs_linux); mw.l f1010100 0020c000; usb reset; ext2load usb 0:1 $(loadaddr) /uImage; ext2load usb 0:1 0x01100000 /uInitrd; bootm $(loadaddr) 0x01100000 bootcmd_stock=setenv bootargs $(bootargs_stock); nand read.e $(loadaddr) $(kernel_addr) 0xA00000; bootm $(loadadr) to_stock=setenv mainlineLinux no; setenv bootcmd \'run bootcmd_stock\'; saveenv; reset to_linux=setenv mainlineLinux yes; setenv bootcmd \'run bootcmd_linux\'; saveenv; reset bootcmd='run bootcmd_linux' stdin=serial stdout=serial stderr=serial mainlineLinux=yes enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no disaMvPnp=no enaAutoRecovery=yes kernel_addr=0x4640000 pcieTune=no pcieTune1=no Environment size: 2498/131068 bytes
Re: NSA325 - Problem booting with Linux Kernel 4.13.5 October 13, 2017 01:18AM |
Admin Registered: 13 years ago Posts: 18,613 |
Quote
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Jul 18 2013 - 10:47:29) Marvell version: 3.5.9
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00
Soc: 88F6282 A1CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 8 tRAS = 24 tRCD=8
DRAM CS[0] base 0x00000000 size 512MB
DRAM Total size 512MB 16bit width
Addresses 10M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (10M - 7M): Done
NAND:128 MB
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Kernel address is 0x4640000.
Streaming disabled
Write allocate disabled
USB 0: host mode
[BlueDBG] reseting SoC Pex[0] 0 ...
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
[BlueDBG] reseting SoC Pex[1] 0 ...
[BlueDBG] reseting SoC Pex[1] 1 ...
[BlueDBG] reseting SoC Pex[1] 2 ...
[BlueDBG] reseting SoC Pex[1] 3 ...
[BlueDBG] reseting SoC Pex[1] 4 ...
[BlueDBG] reseting SoC Pex[1] 5 ...
[BlueDBG] reseting SoC Pex[1] 6 ...
[BlueDBG] reseting SoC Pex[1] 7 ...
[BlueDBG] reseting SoC Pex[1] 8 ...
[BlueDBG] reseting SoC Pex[1] 9 ...
[BlueDBG] reseting SoC Pex[1] 10 ...
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices... 3 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
....
8386386 bytes read
## Booting image at 02000000 ...
Image Name: Linux-4.13.5-kirkwood-tld-1
Created: 2017-10-12 16:12:18 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3862548 Bytes = 3.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
Image Name: initramfs-4.13.5-kirkwood-tld-1
Created: 2017-10-12 16:12:32 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 8386322 Bytes = 8 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
setenv bootargs_linux 'console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=LABEL=rootfs loglevel=8 earlyprintk=serial' setenv bootcmd_linux 'setenv bootargs $(bootargs_linux); mw.l f1010100 0020c000; usb reset; ext2load usb 0:1 $(loadaddr) /boot/uImage; ext2load usb 0:1 0x02100000 /boot/uInitrd; bootm $(loadaddr) 0x02100000' printenv boot
dummy64
Re: NSA325 - stock u-boot problem booting with Linux Kernel 4.13.5 October 14, 2017 05:26PM |
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** MARVELL BOARD: DB-88F6282A-BP LE U-Boot 1.1.4 (Jul 18 2013 - 10:47:29) Marvell version: 3.5.9 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00 Soc: 88F6282 A1CPU running @ 1600Mhz L2 running @ 533Mhz SysClock = 533Mhz , TClock = 200Mhz DRAM (DDR3) CAS Latency = 7 tRP = 8 tRAS = 24 tRCD=8 DRAM CS[0] base 0x00000000 size 512MB DRAM Total size 512MB 16bit width Addresses 10M - 0M are saved for the U-Boot usage. Mem malloc Initialization (10M - 7M): Done NAND:128 MB Flash: 0 kB CPU : Marvell Feroceon (Rev 1) Kernel address is 0x4640000. Streaming disabled Write allocate disabled USB 0: host mode [BlueDBG] reseting SoC Pex[0] 0 ... PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 [BlueDBG] reseting SoC Pex[1] 0 ... [BlueDBG] reseting SoC Pex[1] 1 ... [BlueDBG] reseting SoC Pex[1] 2 ... [BlueDBG] reseting SoC Pex[1] 3 ... [BlueDBG] reseting SoC Pex[1] 4 ... [BlueDBG] reseting SoC Pex[1] 5 ... [BlueDBG] reseting SoC Pex[1] 6 ... [BlueDBG] reseting SoC Pex[1] 7 ... [BlueDBG] reseting SoC Pex[1] 8 ... [BlueDBG] reseting SoC Pex[1] 9 ... [BlueDBG] reseting SoC Pex[1] 10 ... PEX 1: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 Marvell>> printenv bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init bootdelay=2 baudrate=115200 loads_echo=0 ipaddr=10.4.52.165 serverip=10.4.52.7 rootpath=/srv/ubuntu netmask=255.255.255.0 nandEcc=1bit MODEL_ID=AE03 PRODUCT_NAME=NSA-325v2 FEATURE_BIT=00 CONTRY_TYPE=FF VENDOR_NAME=MitraStar Technology Corp. run_diag=yes console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root) ethprime=egiga0 bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; lcd0_enable=0 lcd0_params=640x480-16@60 ethaddr=00:50:43:00:02:02 ethmtu=1500 mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no image_multi=yes ethact=egiga0 arcNumber=4495 bootargs_stock=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init bootargs_linux=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=LABEL=rootfs loglevel=8 bootcmd_linux=setenv bootargs $(bootargs_linux); mw.l f1010100 0020c000; usb reset; ext2load usb 0:1 $(loadaddr) /uImage; ext2load usb 0:1 0x01100000 /uInitrd; bootm $(loadaddr) 0x01100000 bootcmd_stock=setenv bootargs $(bootargs_stock); nand read.e $(loadaddr) $(kernel_addr) 0xA00000; bootm $(loadadr) to_stock=setenv mainlineLinux no; setenv bootcmd \'run bootcmd_stock\'; saveenv; reset to_linux=setenv mainlineLinux yes; setenv bootcmd \'run bootcmd_linux\'; saveenv; reset bootcmd='run bootcmd_linux' stdin=serial stdout=serial stderr=serial mainlineLinux=yes enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no disaMvPnp=no enaAutoRecovery=yes kernel_addr=0x4640000 pcieTune=no pcieTune1=no Environment size: 2498/131068 bytes Marvell>> setenv bootargs_linux 'console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=LABEL=rootfs loglevel=8 earlyprintk=serial' Marvell>> setenv bootcmd_linux 'setenv bootargs $(bootargs_linux); mw.l f1010100 0020c000; usb reset; ext2load usb 0:1 $(loadaddr) /boot/uImage; ext2load usb 0:1 0x02100000 /boot/uInitrd; bootm $(loadaddr) 0x02100000' Marvell>> printenv bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init bootdelay=2 baudrate=115200 loads_echo=0 ipaddr=10.4.52.165 serverip=10.4.52.7 rootpath=/srv/ubuntu netmask=255.255.255.0 nandEcc=1bit MODEL_ID=AE03 PRODUCT_NAME=NSA-325v2 FEATURE_BIT=00 CONTRY_TYPE=FF VENDOR_NAME=MitraStar Technology Corp. run_diag=yes console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root) ethprime=egiga0 bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; lcd0_enable=0 lcd0_params=640x480-16@60 ethaddr=00:50:43:00:02:02 ethmtu=1500 mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no image_multi=yes ethact=egiga0 arcNumber=4495 bootargs_stock=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init bootcmd_stock=setenv bootargs $(bootargs_stock); nand read.e $(loadaddr) $(kernel_addr) 0xA00000; bootm $(loadadr) to_stock=setenv mainlineLinux no; setenv bootcmd \'run bootcmd_stock\'; saveenv; reset to_linux=setenv mainlineLinux yes; setenv bootcmd \'run bootcmd_linux\'; saveenv; reset bootcmd='run bootcmd_linux' stdin=serial stdout=serial stderr=serial mainlineLinux=yes enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no disaMvPnp=no enaAutoRecovery=yes kernel_addr=0x4640000 pcieTune=no pcieTune1=no bootargs_linux=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=LABEL=rootfs loglevel=8 earlyprintk=serial bootcmd_linux=setenv bootargs $(bootargs_linux); mw.l f1010100 0020c000; usb reset; ext2load usb 0:1 $(loadaddr) /boot/uImage; ext2load usb 0:1 0x02100000 /boot/uInitrd; bootm $(loadaddr) 0x02100000 Environment size: 2527/131068 bytes Marvell>>boot (Re)start USB... USB: scanning bus for devices... 3 USB Device(s) found Waiting for storage device(s) to settle before scanning... 1 Storage Device(s) found ** Unable to read "/boot/uImage" from usb 0:1 ** ** Unable to read "/boot/uInitrd" from usb 0:1 ** ## Booting image at 02000000 ... Bad Magic Number Marvell>>
Re: NSA325 - stock u-boot problem booting with Linux Kernel 4.13.5 October 14, 2017 07:12PM |
Admin Registered: 13 years ago Posts: 18,613 |
/boot/uImage /boot/uInitrdNote: /boot here is a folder, not parttition name.