Need help giving new life to a previously Bricked Pogoplug V4 December 28, 2017 09:21PM |
Registered: 6 years ago Posts: 6 |
Re: Need help giving new life to a previously Bricked Pogoplug V4 December 28, 2017 09:22PM |
Registered: 6 years ago Posts: 6 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:34:01 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: MVEBU_MMC: 0 In: serial Out: serial Err: serial Net: egiga0 Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.1.100 is not alive Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Reset IDE: ide_preinit failed MMC rescan: current device # 0 initialized OK ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... ** Bad device usb 0 ** no IDE devices available Partition Map for MMC device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type loading envs from mmc 0 ... ** Invalid partition 1 ** running scan_disk ... Scan device usb device usb 0:1 ** Bad device usb 0 ** device usb 1:1 ** Bad device usb 1 ** device usb 2:1 ** Bad device usb 2 ** device usb 3:1 ** Bad device usb 3 ** Scan device ide Reset IDE: ide_preinit failed device ide 0:1 ** Bad device ide 0 ** device ide 1:1 ** Bad device ide 1 ** device ide 2:1 ** Bad device ide 2 ** device ide 3:1 ** Bad device ide 3 ** Scan device mmc MMC rescan: current device # 0 initialized OK device mmc 0:1 ** Invalid partition 1 ** device mmc 1:1 MMC Device 1 not found MMC Device 1 not found ** Bad device mmc 1 ** device mmc 2:1 MMC Device 2 not found MMC Device 2 not found ** Bad device mmc 2 ** device mmc 3:1 MMC Device 3 not found MMC Device 3 not found ** Bad device mmc 3 ** loading uImage ... ** Bad device usb 0 ** loading uInitrd ... ** Bad device usb 0 ** loading DTB /boot/dts/kirkwood-pogo_e02.dtb ... ** Bad device usb 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! Pogov4>
Re: Need help giving new life to a previously Bricked Pogoplug V4 December 28, 2017 09:24PM |
Registered: 6 years ago Posts: 6 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:34:01 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: MVEBU_MMC: 0 In: serial Out: serial Err: serial Net: egiga0 Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.1.100 is not alive Hit any key to stop autoboot: 0 Pogov4> printenv arcNumber=3960 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-pogo_e02.dtb ethact=egiga0 ethaddr=52:3b:20:9c:11:51 if_netconsole=ping $serverip ipaddr=192.168.1.10 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 machid=F78 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) partition=nand0,2 preboot=run if_netconsole start_netconsole preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.1.100 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15 usb_rootfstype=ext3 Environment size: 2940/131068 bytes Pogov4>
Re: Need help giving new life to a previously Bricked Pogoplug V4 December 28, 2017 09:29PM |
Registered: 6 years ago Posts: 6 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:34:01 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: MVEBU_MMC: 0 In: serial Out: serial Err: serial Net: egiga0 Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.1.100 is not alive Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Reset IDE: ide_preinit failed MMC rescan: current device # 0 initialized OK Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 7819264 b3755a46-01 83 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** no IDE devices available Partition Map for MMC device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type loading envs from mmc 0 ... ** Invalid partition 1 ** running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 1291 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 3833487 bytes read in 1552 ms (2.4 MiB/s) loading uInitrd ... 7245696 bytes read in 1591 ms (4.3 MiB/s) loading DTB /boot/dts/kirkwood-pogo_e02.dtb ... 10444 bytes read in 4182 ms (2 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.12.1-kirkwood-tld-1 Created: 2017-12-28 13:22:19 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3833423 Bytes = 3.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.12.1-kirkwood-tld-1 Created: 2017-07-24 0:18:23 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7245632 Bytes = 6.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 07420000, end 07b08f40 ... OK Loading Device Tree to 0741a000, end 0741f8cb ... OK Using machid 0xf78 from environment Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.1-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: Seagate GoFlex Net [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10 [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 116496K/131072K available (8192K kernel code, 716K rwdata, 1972K rodata, 1024K init, 288K bss, 14576K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db3274 ( 717 kB) [ 0.000000] .bss : 0xc0db9b9c - 0xc0e01e60 ( 289 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 0.000012] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 0.007935] Switching to timer-based delay loop, resolution 6ns [ 0.014612] Console: colour dummy device 80x30 [ 0.019230] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666) [ 0.029876] pid_max: default: 32768 minimum: 301 [ 0.034859] Security Framework initialized [ 0.039276] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.045967] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.054423] CPU: Testing write buffer coherency: ok [ 0.060986] Setting up static identity map for 0x100000 - 0x100058 [ 0.067621] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.077906] devtmpfs: initialized [ 0.087866] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.097889] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.104724] prandom: seed boundary self test passed [ 0.115344] prandom: 100 self tests passed [ 0.119578] pinctrl core: initialized pinctrl subsystem [ 0.126616] NET: Registered protocol family 16 [ 0.131935] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.141323] cpuidle: using governor ladder [ 0.145595] cpuidle: using governor menu [ 0.150307] Feroceon L2: Enabling L2 [ 0.154004] Feroceon L2: Cache support initialised. [ 0.159529] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.176851] No ATAGs? [ 0.190353] vgaarb: loaded [ 0.195926] SCSI subsystem initialized [ 0.200495] usbcore: registered new interface driver usbfs [ 0.206143] usbcore: registered new interface driver hub [ 0.211680] usbcore: registered new device driver usb [ 0.218426] clocksource: Switched to clocksource orion_clocksource [ 0.356946] VFS: Disk quotas dquot_6.6.0 [ 0.361149] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.383045] NET: Registered protocol family 2 [ 0.388612] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.395657] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.402124] TCP: Hash tables configured (established 1024 bind 1024) [ 0.408682] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.414594] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.421194] NET: Registered protocol family 1 [ 0.426190] RPC: Registered named UNIX socket transport module. [ 0.432280] RPC: Registered udp transport module. [ 0.437054] RPC: Registered tcp transport module. [ 0.441867] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.448907] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.456782] audit: initializing netlink subsys (disabled) [ 0.462963] Initialise system trusted keyrings [ 0.467528] Key type blacklist registered [ 0.471708] audit: type=2000 audit(0.454:1): state=initialized audit_enabled=0 res=1 [ 0.479763] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 0.486342] zbud: loaded [ 0.490463] NFS: Registering the id_resolver key type [ 0.495601] Key type id_resolver registered [ 0.499929] Key type id_legacy registered [ 0.504021] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.510825] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.517509] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.524915] fuse init (API version 7.26) [ 0.529464] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.536349] orangefs_init: module version upstream loaded [ 0.541857] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 2.558436] random: fast init done [ 9.310449] Key type asymmetric registered [ 9.314623] Asymmetric key parser 'x509' registered [ 9.319970] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 9.327427] io scheduler noop registered [ 9.331505] io scheduler deadline registered [ 9.335941] io scheduler cfq registered (default) [ 9.342650] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 9.352646] mv_xor f1060800.xor: Marvell shared XOR driver [ 9.419551] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 9.427488] mv_xor f1060900.xor: Marvell shared XOR driver [ 9.489550] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 9.497762] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 9.506063] console [ttyS0] disabled [ 9.509888] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 10416666) is a 16550A [ 9.519015] console [ttyS0] enabled [ 9.519015] console [ttyS0] enabled [ 9.526042] bootconsole [earlycon0] disabled [ 9.526042] bootconsole [earlycon0] disabled [ 9.547132] loop: module loaded [ 9.551153] sata_mv f1080000.sata: slots 32 ports 2 [ 9.559956] scsi host0: sata_mv [ 9.563696] scsi host1: sata_mv [ 9.567154] ata1: SATA max UDMA/133 irq 32 [ 9.571316] ata2: SATA max UDMA/133 irq 32 [ 9.576938] nand: Could not find valid ONFI parameter page; aborting [ 9.583391] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 9.589748] nand: Hynix NAND 128MiB 3,3V 8-bit [ 9.594180] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 9.601758] Scanning device for bad blocks [ 9.691393] Bad eraseblock 758 at 0x000005ec0000 [ 9.725919] 4 ofpart partitions found on MTD device orion_nand [ 9.731753] Creating 4 MTD partitions on "orion_nand": [ 9.736884] 0x000000000000-0x000000100000 : "u-boot" [ 9.743671] 0x000000100000-0x000000500000 : "uImage" [ 9.750514] 0x000000500000-0x000002500000 : "pogoplug" [ 9.757724] 0x000002500000-0x00000fd00000 : "root" [ 9.762586] mtd: partition "root" extends beyond the end of device "orion_nand" -- size truncated to 0x5b00000 [ 9.777078] libphy: Fixed MDIO Bus: probed [ 9.782386] libphy: orion_mdio_bus: probed [ 9.787635] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 9.901045] ata1: SATA link down (SStatus 0 SControl F300) [ 10.249963] ata2: SATA link down (SStatus 0 SControl F300) [ 10.900445] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 52:3b:20:9c:11:51 [ 10.909331] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 10.915858] ehci-pci: EHCI PCI platform driver [ 10.920402] ehci-orion: EHCI orion driver [ 10.924692] orion-ehci f1050000.ehci: EHCI Host Controller [ 10.930253] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 10.938109] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 10.968474] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 10.974822] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 10.981626] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.988851] usb usb1: Product: EHCI Host Controller [ 10.993714] usb usb1: Manufacturer: Linux 4.12.1-kirkwood-tld-1 ehci_hcd [ 11.000419] usb usb1: SerialNumber: f1050000.ehci [ 11.006061] hub 1-0:1.0: USB hub found [ 11.009931] hub 1-0:1.0: 1 port detected [ 11.014739] usbcore: registered new interface driver usb-storage [ 11.021279] mousedev: PS/2 mouse device common for all mice [ 11.368472] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 11.559492] usb 1-1: New USB device found, idVendor=0781, idProduct=5575 [ 11.566193] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 11.573352] usb 1-1: Product: Cruzer Glide [ 11.577432] usb 1-1: Manufacturer: SanDisk [ 11.581537] usb 1-1: SerialNumber: 4C530200271031104534 [ 11.587795] usb-storage 1-1:1.0: USB Mass Storage device detected [ 11.594409] scsi host2: usb-storage 1-1:1.0 [ 12.088473] rtc-mv f1010300.rtc: internal RTC not ticking [ 12.094100] i2c /dev entries driver [ 12.101494] hidraw: raw HID events driver (C) Jiri Kosina [ 12.107439] drop_monitor: Initializing network drop monitor service [ 12.114097] NET: Registered protocol family 17 [ 12.118681] Key type dns_resolver registered [ 12.124078] registered taskstats version 1 [ 12.128160] Loading compiled-in X.509 certificates [ 12.133060] zswap: loaded using pool lzo/zbud [ 12.141011] Key type big_key registered [ 12.147429] Key type encrypted registered [ 12.153379] hctosys: unable to open rtc device (rtc0) [ 12.159091] Waiting 10 sec before mounting root device... [ 12.649759] scsi 2:0:0:0: Direct-Access SanDisk Cruzer Glide 2.01 PQ: 0 ANSI: 6 [ 12.660311] sd 2:0:0:0: [sda] 7821312 512-byte logical blocks: (4.00 GB/3.73 GiB) [ 12.669293] sd 2:0:0:0: [sda] Write Protect is off [ 12.674780] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 12.688375] sda: sda1 [ 12.694658] sd 2:0:0:0: [sda] Attached SCSI disk [ 22.249716] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 22.269079] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 22.276800] VFS: Mounted root (ext3 filesystem) readonly on device 8:1. [ 22.293003] devtmpfs: mounted [ 22.300919] Freeing unused kernel memory: 1024K INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. ERROR: could not open /proc/stat: No such file or directory findfs: unable to resolve 'LABEL=rootfs' [....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232 . ok [ ok ] Synthesizing the initial hotplug events...done. [....] Waiting for /dev to be fully populated...[ 24.952447] marvell-cesa f1030000.crypto: CESA device successfully registered [ 24.985413] orion_wdt: Initial timeout 25 sec [ 25.042092] usbcore: registered new interface driver uas [ 25.119886] sd 2:0:0:0: Attached scsi generic sg0 type 0 done. [ ok ] Setting hostname to 'debian'...done. [ ok ] Activating swap:. [ 26.739689] EXT4-fs (sda1): re-mounted. Opts: (null) [....] Will now check root file system:fsck from util-linux 2.29.2 [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sda1 e2fsck 1.43.4 (31-Jan-2017) rootfs: clean, 14494/244800 files, 221645/977408 blocks . ok [ 27.081140] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ ok ] Will now activate lvm and md swap:[ 28.216315] random: crng init done done. [info] Will now check all file systems. fsck from util-linux 2.29.2 Checking all file systems. LABEL=rootfs is mounted [ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. [ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done. [ ok . [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables...done. [ ok ] Initializing random number generator...done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5 Copyright 2004-2016 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/52:3b:20:9c:11:51 Sending on LPF/eth0/52:3b:20:9c:11:51 Sending on Socket/fallback DHCPREQUEST of 192.168.1.23 on eth0 to 255.255.255.255 port 67 [ 35.322190] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 37.543795] NET: Registered protocol family 10 [ 37.552265] Segment Routing with IPv6 DHCPREQUEST of 192.168.1.23 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.1.23 from 192.168.1.1 bound to 192.168.1.23 -- renewal in 35080 seconds. done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1257 (syslogd) . ok [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [ ok ] Starting NFS common utilities: statd idmapd. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1256 (klogd) . ok [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Running local boot scripts (/etc/rc.local). Debian GNU/Linux 9 debian ttyS0 debian login: root Password: Last login: Wed Dec 31 16:02:06 PST 1969 on ttyS0 Linux debian 4.12.1-kirkwood-tld-1 #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 armv5tel The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@debian:~#
Re: Need help giving new life to a previously Bricked Pogoplug V4 December 28, 2017 11:10PM |
Admin Registered: 13 years ago Posts: 18,495 |
Quote
> My question is that if there is any way to
> restore it in a way that I can boot it from
> sdcard.
Quote
4. Create uImage with embedded DTB for booting with older u-boots (2012 or earlier). Skip this step if you have installed the latest U-Boot for Kirkwood (or are installing this u-boot at the same time).
setenv devices 'mmc usb ide' setenv dtb_file '/boot/dts/kirkwood-pogoplug_v4.dtb'
boot
Re: Need help giving new life to a previously Bricked Pogoplug V4 December 29, 2017 03:09AM |
Registered: 6 years ago Posts: 6 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:34:01 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: MVEBU_MMC: 0 In: serial Out: serial Err: serial Net: egiga0 Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.1.100 is not alive Hit any key to stop autoboot: 0 Pogov4> setenv devices 'mmc usb ide' Pogov4> setenv dtb_file '/boot/dts/kirkwood-pogoplug_v4.dtb' Pogov4> boot MMC rescan: current device # 0 initialized OK starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Reset IDE: ide_preinit failed Partition Map for MMC device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 15521792 20a95607-01 83 loading envs from mmc 0 ... ** File not found /boot/uEnv.txt ** ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... ** Bad device usb 0 ** no IDE devices available running scan_disk ... Scan device mmc MMC rescan: current device # 0 initialized OK device mmc 0:1 1 bytes read in 19 ms (0 Bytes/s) Found bootable drive on mmc 0 loading uImage ... 3821592 bytes read in 222 ms (16.4 MiB/s) loading uInitrd ... 7245696 bytes read in 398 ms (17.4 MiB/s) loading DTB /boot/dts/kirkwood-pogoplug_v4.dtb ... 10284 bytes read in 46 ms (217.8 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.12.1-kirkwood-tld-1 Created: 2017-07-20 8:11:24 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3821528 Bytes = 3.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.12.1-kirkwood-tld-1 Created: 2017-07-24 0:18:23 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7245632 Bytes = 6.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 07420000, end 07b08f40 ... OK Loading Device Tree to 0741a000, end 0741f82b ... OK Using machid 0xf78 from environment Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.1-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397 f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: Pogoplug v4 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootd elay=10 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M( root) [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 109428K/131072K available (8192K kernel code, 716K rwdata , 1972K rodata, 1024K init, 288K bss, 21644K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db3274 ( 717 kB) [ 0.000000] .bss : 0xc0db9b9c - 0xc0e01e60 ( 289 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xff ffffff, max_idle_ns: 11467562657 ns [ 0.000012] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884 901885ns [ 0.000067] Switching to timer-based delay loop, resolution 6ns [ 0.000765] Console: colour dummy device 80x30 [ 0.000815] Calibrating delay loop (skipped), value calculated using timer fr equency.. 333.33 BogoMIPS (lpj=1666666) [ 0.000850] pid_max: default: 32768 minimum: 301 [ 0.001145] Security Framework initialized [ 0.001328] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001357] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.002651] CPU: Testing write buffer coherency: ok [ 0.004214] Setting up static identity map for 0x100000 - 0x100058 [ 0.004613] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.009526] devtmpfs: initialized [ 0.015389] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns [ 0.015431] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.016052] prandom: seed boundary self test passed [ 0.021786] prandom: 100 self tests passed [ 0.021811] pinctrl core: initialized pinctrl subsystem [ 0.023551] NET: Registered protocol family 16 [ 0.024291] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.026647] cpuidle: using governor ladder [ 0.026753] cpuidle: using governor menu [ 0.027401] Feroceon L2: Enabling L2 [ 0.027466] Feroceon L2: Cache support initialised. [ 0.028014] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet 0-port@0: local-mac-address is not set [ 0.035042] No ATAGs? [ 0.048336] vgaarb: loaded [ 0.048799] SCSI subsystem initialized [ 0.049463] usbcore: registered new interface driver usbfs [ 0.049589] usbcore: registered new interface driver hub [ 0.049710] usbcore: registered new device driver usb [ 0.051385] clocksource: Switched to clocksource orion_clocksource [ 0.183739] VFS: Disk quotas dquot_6.6.0 [ 0.183856] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.198753] NET: Registered protocol family 2 [ 0.199815] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.199858] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.199888] TCP: Hash tables configured (established 1024 bind 1024) [ 0.200018] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.200053] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.200303] NET: Registered protocol family 1 [ 0.200890] RPC: Registered named UNIX socket transport module. [ 0.200908] RPC: Registered udp transport module. [ 0.200919] RPC: Registered tcp transport module. [ 0.200929] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.201265] Unpacking initramfs... [ 1.168539] Freeing initrd memory: 7076K [ 1.168746] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.170124] audit: initializing netlink subsys (disabled) [ 1.170827] Initialise system trusted keyrings [ 1.170919] Key type blacklist registered [ 1.171051] audit: type=2000 audit(1.169:1): state=initialized audit_enabled= 0 res=1 [ 1.171183] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 1.171281] zbud: loaded [ 1.172805] NFS: Registering the id_resolver key type [ 1.172849] Key type id_resolver registered [ 1.172862] Key type id_legacy registered [ 1.172887] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.172902] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.173188] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.173466] fuse init (API version 7.26) [ 1.173980] orangefs_debugfs_init: called with debug mask: :none: :0: [ 1.174379] orangefs_init: module version upstream loaded [ 1.174395] SGI XFS with ACLs, security attributes, realtime, no debug enable d [ 2.551396] random: fast init done [ 9.945324] Key type asymmetric registered [ 9.945348] Asymmetric key parser 'x509' registered [ 9.945448] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 49) [ 9.945464] io scheduler noop registered [ 9.945476] io scheduler deadline registered [ 9.945591] io scheduler cfq registered (default) [ 9.946845] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 4 7 [ 9.946871] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 4 9 [ 9.947370] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driv er [ 9.950172] mvebu-pcie mbus@f1000000:pcie-controller@82000000: PCI host bridg e to bus 0000:00 [ 9.950203] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 9.950223] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 9.950243] pci_bus 0000:00: root bus resource [bus 00-ff] [ 9.950727] PCI: bus0: Fast back to back transfers disabled [ 9.950762] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), rec onfiguring [ 9.950989] PCI: bus1: Fast back to back transfers enabled [ 9.951098] pci 0000:00:01.0: PCI bridge to [bus 01] [ 9.952155] mv_xor f1060800.xor: Marvell shared XOR driver [ 10.012521] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg i ntr ) [ 10.012837] mv_xor f1060900.xor: Marvell shared XOR driver [ 10.072503] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg i ntr ) [ 10.073127] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 10.075011] console [ttyS0] disabled [ 10.075108] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 10416666) is a 16550A [ 10.735998] console [ttyS0] enabled [ 10.751996] loop: module loaded [ 10.755946] sata_mv f1080000.sata: slots 32 ports 2 [ 10.764748] scsi host0: sata_mv [ 10.768512] scsi host1: sata_mv [ 10.772062] ata1: SATA max UDMA/133 irq 32 [ 10.776148] ata2: SATA max UDMA/133 irq 32 [ 10.781729] nand: Could not find valid ONFI parameter page; aborting [ 10.788073] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 10.794498] nand: Hynix NAND 128MiB 3,3V 8-bit [ 10.798933] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB siz e: 64 [ 10.806514] Scanning device for bad blocks [ 10.873402] Bad eraseblock 758 at 0x000005ec0000 [ 10.899983] 5 cmdlinepart partitions found on MTD device orion_nand [ 10.906250] Creating 5 MTD partitions on "orion_nand": [ 10.911405] 0x000000000000-0x000000200000 : "u-boot" [ 10.918185] 0x000000200000-0x000000500000 : "uImage" [ 10.925001] 0x000000500000-0x000000800000 : "uImage2" [ 10.931892] 0x000000800000-0x000001000000 : "failsafe" [ 10.938955] 0x000001000000-0x000008000000 : "root" [ 10.948209] libphy: Fixed MDIO Bus: probed [ 10.953506] libphy: orion_mdio_bus: probed [ 10.964873] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 11.113041] ata1: SATA link down (SStatus 0 SControl F300) [ 11.462916] ata2: SATA link down (SStatus 0 SControl F300) [ 12.083515] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 52:3b:20:9c:11:51 [ 12.092410] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 12.098943] ehci-pci: EHCI PCI platform driver [ 12.103491] ehci-orion: EHCI orion driver [ 12.107779] orion-ehci f1050000.ehci: EHCI Host Controller [ 12.113329] orion-ehci f1050000.ehci: new USB bus registered, assigned bus nu mber 1 [ 12.121191] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 12.151434] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 12.157753] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 12.164560] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 12.171786] usb usb1: Product: EHCI Host Controller [ 12.176651] usb usb1: Manufacturer: Linux 4.12.1-kirkwood-tld-1 ehci_hcd [ 12.183353] usb usb1: SerialNumber: f1050000.ehci [ 12.189001] hub 1-0:1.0: USB hub found [ 12.192878] hub 1-0:1.0: 1 port detected [ 12.197740] usbcore: registered new interface driver usb-storage [ 12.204278] mousedev: PS/2 mouse device common for all mice [ 13.281426] rtc-mv f1010300.rtc: internal RTC not ticking [ 13.287051] i2c /dev entries driver [ 13.292567] hidraw: raw HID events driver (C) Jiri Kosina [ 13.298483] drop_monitor: Initializing network drop monitor service [ 13.305137] NET: Registered protocol family 17 [ 13.309686] Key type dns_resolver registered [ 13.315096] registered taskstats version 1 [ 13.319184] Loading compiled-in X.509 certificates [ 13.324087] zswap: loaded using pool lzo/zbud [ 13.342959] Key type big_key registered [ 13.360473] Key type encrypted registered [ 13.366649] hctosys: unable to open rtc device (rtc0) [ 13.376769] Freeing unused kernel memory: 1024K Loading, please wait... starting version 232 [ 14.030341] mvsdio f1090000.mvsdio: Got CD GPIO [ 14.169177] mmc0: host does not support reading read-only switch, assuming wr ite-enable [ 14.187215] mmc0: new high speed SDHC card at address aaaa [ 14.387647] mmcblk0: mmc0:aaaa SU08G 7.40 GiB [ 14.396381] mmcblk0: p1 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Warning: fsck not present, so skipping root file system [ 24.745329] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 sub system [ 24.754671] EXT4-fs (mmcblk0p1): INFO: recovery required on readonly filesyst em [ 24.762047] EXT4-fs (mmcblk0p1): write access will be enabled during recovery [ 54.672594] EXT4-fs (mmcblk0p1): recovery complete [ 54.686538] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. O pts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [ ok ] Setting hostname to 'debian'...done. [....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232 . ok [....] Synthesizing the initial hotplug events...[ 57.161638] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [ ok done. [....] Waiting for /dev to be fully populated...[ 57.590658] orion_wdt: Initia l timeout 25 sec [ 57.702963] marvell-cesa f1030000.crypto: CESA device successfully registered done. [ ok ] Activating swap:. [ 59.247532] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null) [....] Will now check root file system:fsck from util-linux 2.29.2 [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/mmcblk0p1 e2fsck 1.43.4 (31-Jan-2017) rootfs: clean, 14453/485760 files, 235925/1940224 blocks . ok [ 59.549087] EXT4-fs (mmcblk0p1): re-mounted. Opts: errors=remount-ro [ ok ] Will now activate lvm and md swap:done. [info] Will now check all file systems. fsck from util-linux 2.29.2 Checking all file systems. LABEL=rootfs is mounted [....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs [ ok hat location is writable.. [ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done. [ ok . [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables...done. [ ok ] Initializing random number generator...done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5 Copyright 2004-2016 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/52:3b:20:9c:11:51 Sending on LPF/eth0/52:3b:20:9c:11:51 Sending on Socket/fallback DHCPREQUEST of 192.168.0.14 on eth0 to 255.255.255.255 port 67 [ 67.425182] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, ful l duplex, flow control disabled [ 69.331863] NET: Registered protocol family 10 [ 69.342837] Segment Routing with IPv6 DHCPREQUEST of 192.168.0.14 on eth0 to 255.255.255.255 port 67 DHCPNAK from 169.254.255.1 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7 DHCPREQUEST of 192.168.1.23 on eth0 to 255.255.255.255 port 67 DHCPOFFER of 192.168.1.23 from 192.168.1.1 DHCPACK of 192.168.1.23 from 192.168.1.1 bound to 192.168.1.23 -- renewal in 34957 seconds. done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd. .. 1325 (syslogd) . ok [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1324 (klogd) . ok [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Running local boot scripts (/etc/rc.local). Debian GNU/Linux 9 debian ttyS0 debian login: root Password: Last login: Wed Dec 31 16:01:32 PST 1969 from 192.168.0.220 on pts/0 Linux debian 4.12.1-kirkwood-tld-1 #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 armv5 tel The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@debian:~# rm /etc/ssh/ssh_host* root@debian:~# ssh-keygen -A ssh-keygen: generating new host keys: RSA [ 151.921600] random: crng init done root@debian:~#
Re: Need help giving new life to a previously Bricked Pogoplug V4 December 29, 2017 03:39AM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: Need help giving new life to a previously Bricked Pogoplug V4 December 30, 2017 07:02AM |
Registered: 6 years ago Posts: 6 |
Re: Need help giving new life to a previously Bricked Pogoplug V4 December 30, 2017 07:31AM |
Admin Registered: 13 years ago Posts: 18,495 |