NAS Iconbit I-STOR IS608 with Linux Kernel 4.4.89 Oxnas (OX820)

There was a version (NAS Iconbit I-STOR IS608). Previous messages here

root @ debian: ~ # cat /proc/version
Linux version 4.1.0-oxnas-tld-1 (root @ tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10)) # 3 SMP PREEMPT Wed Jul 1 05:11:47 PDT 2015

Installed from the first page linux-4.4.89-oxnas-tld-1.bodhi.tar.bz2

root@debian:~# cat /proc/version
Linux version 4.4.89-oxnas-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18) ) #1 SMP PREEMPT Wed Oct 4 22:22:09 PDT 2017

WiFi usb are defined

TEW-684UB

[  127.520281] usb 1-2: new high-speed USB device number 2 using oxnas-ehci
[  127.686799] usb 1-2: New USB device found, idVendor=148f, idProduct=3573
[  127.693529] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  127.700712] usb 1-2: Product: 802.11 n WLAN
[  127.705100] usb 1-2: Manufacturer: Ralink
[  127.709102] usb 1-2: SerialNumber: 1.0
[  127.990028] usb 1-2: reset high-speed USB device number 2 using oxnas-ehci
[  128.149688] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3593, rev 0402 detected
[  128.186296] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 000d detected
[  128.198382] usbcore: registered new interface driver rt2800usb

DWA-140 rev B2

[  235.971694] usb 1-2: USB disconnect, device number 2
[  254.000053] usb 1-2: new high-speed USB device number 3 using oxnas-ehci
[  254.166174] usb 1-2: New USB device found, idVendor=07d1, idProduct=3c0a
[  254.172904] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  254.180096] usb 1-2: Product: 11n Adapter
[  254.184094] usb 1-2: Manufacturer: Ralink
[  254.188085] usb 1-2: SerialNumber: 1.0
[  254.320058] usb 1-2: reset high-speed USB device number 3 using oxnas-ehci
[  254.479685] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 3071, rev 0213 detected
[  254.516418] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 0008 detected

TEW-664-UB

[  316.629611] usb 1-2: USB disconnect, device number 3
[  325.350074] usb 1-2: new high-speed USB device number 4 using oxnas-ehci
[  325.518046] usb 1-2: New USB device found, idVendor=148f, idProduct=2870
[  325.524779] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  325.531962] usb 1-2: Product: 802.11 n WLAN
[  325.536135] usb 1-2: Manufacturer: Ralink
[  325.540160] usb 1-2: SerialNumber: 1.0
[  325.670077] usb 1-2: reset high-speed USB device number 4 using oxnas-ehci
[  325.831057] ieee80211 phy2: rt2x00_set_rt: Info - RT chipset 2872, rev 0202 detected
[  325.893309] ieee80211 phy2: rt2x00_set_rf: Info - RF chipset 0002 detected

DWA -131

[  417.880094] usb 1-2: new high-speed USB device number 6 using oxnas-ehci
[  418.032921] usb 1-2: New USB device found, idVendor=07d1, idProduct=3303
[  418.039603] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  418.046789] usb 1-2: Product: 11n Adapter
[  418.050816] usb 1-2: Manufacturer: Manufacturer Realtek
[  418.056104] usb 1-2: SerialNumber: 00e04c000001

DWA -131 no line ieee80211 phy......, no wlan0

Question: How to raise wlan interface and what other packages do I need to install? Thank you

root@debian:~#  ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT qlen 1
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN mode DEFAULT qlen 1000
    link/ether 74:f0:6d:6a:1d:17 brd ff:ff:ff:ff:ff:ff
3: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT qlen 1
    link/sit 0.0.0.0 brd 0.0.0.0
4: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT qlen 1000
    link/ether f0:7d:68:71:18:34 brd ff:ff:ff:ff:ff:ff
root@debian:~# ip link set wlan0 up
[  357.880258] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[  357.909102] rt2800usb 1-2:1.0: Direct firmware load for rt2870.bin failed with error -2
[  357.917201] ieee80211 phy0: rt2x00lib_request_firmware: Error - Failed to request Firmware
RTNETLINK answers: No such file or directory
root@debian:~# dmesg | grep firmware
[  357.880258] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[  357.909102] rt2800usb 1-2:1.0: Direct firmware load for rt2870.bin failed with error -2
[  357.917201] ieee80211 phy0: rt2x00lib_request_firmware: Error - Failed to request Firmware

P.S. Took from debian8 and inserted /lib/firmware/4.4.89-oxnas-tld-1/rt2870.bin

root@debian:~# ip link set wlan0 up
[   67.000051] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[   67.031656] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.29
[   67.447644] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
root@debian:~# ifconfig
eth0      Link encap:Ethernet  HWaddr 74:f0:6d:6a:1d:17
          inet addr:192.168.3.179  Bcast:192.168.3.255  Mask:255.255.255.0
          inet6 addr: fe80::76f0:6dff:fe6a:1d17/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:22 errors:0 dropped:0 overruns:0 frame:0
          TX packets:75 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:2339 (2.2 KiB)  TX bytes:10172 (9.9 KiB)
          Interrupt:8 Base address:0xc000

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

wlan0     Link encap:Ethernet  HWaddr ff:ff:ff:ff:ff:ff
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

Edited 17 time(s). Last edit at 02/03/2018 06:50PM by sakatgg.