Need help with Lenovo ix2-ng July 17, 2019 04:02PM |
Registered: 4 years ago Posts: 3 |
0. sudo su => All commands were run under root@AlDaniel 1. Used gparted to format the usb stick with ext2 and the name rootfs 2. mount /dev/sdg1 /media/sdb1/ 3. cd /media/sdb1/ 4. tar -xjf Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2 5. cd etc/ 6. vi fstab 7. Modified fstab by changing ext3 to ext2 8. cd .. 9. cd boot/ 10. cp -a zImage-4.12.1-kirkwood-tld-1 zImage.fdt 11. cat dts/kirkwood-lenovo-ix2-ng.dtb >> zImage.fdt 12. mv uImage uImage.orig 13. mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-4.12.1-kirkwood-tld-1 -d zImage.fdt uImage 14. sync 15. cd /home/ 16. umount /media/sdb1/
setenv load_initrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd' setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' setenv bootargs 'console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x80000@0(uboot),0x20000@0xa0000 (env),0x20000@0xc0000(env2),0x300000@0x100000(uImage),0x400000@0x400000(initrd),0x3f800000@0x800000 (boot),1024m@0x0(flash) earlyprintk=serial' setenv usb_boot 'usb start; run load_uimage; run load_initrd; bootm 0x800000 0x2100000' setenv bootcmd 'run usb_boot' setenv usb_root 'LABEL=rootfs' setenv rootdelay 10 boot
(Re)start USB... USB: scanning bus for devices... 2 USB Device(s) found Waiting for storage device(s) to settle before scanning... 1 Storage Device(s) found T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T Device NOT ready Request Sense returned 00 00 00 T T T T T T T T T T T T T T T T T T T T T T Device NOT ready Request Sense returned 00 00 00 ** ext2fs_devread() read error ** ** Unable to read "/boot/uImage" from usb 0:1 ** T T T T T T T T T T T T T T T T T T T T T T Device NOT ready Request Sense returned 00 00 00 ** Can't read partition table on 0:0 ** ** Bad partition 1 ** ## Booting image at 00800000 ... Bad Magic Number
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 ** ** MARVELL BOARD: DB-88F6282A-BP LE U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0 Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 800Mhz SysClock = 533Mhz , TClock = 200Mhz DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done Found ADT7473, program PWM1 ... OK [1024kB@f8000000] Flash: 1 MB Marvell Serial ATA Adapter Integrated Sata device found [0 0 0]: Enable DMA mode (6) Device 0 @ 0 0: Model: WDC WD800JD-75MSA3 Firm: 10.01E04 Ser#: WD-WMAM9AM21410 Type: Hard Disk Supports 48-bit addressing Capacity: 76293.9 MB = 74.5 GB (156250000 x 512) [0 1 0]: Enable DMA mode (6) Device 1 @ 0 1: Model: WDC WD800JD-75MSA3 Firm: 10.01E04 Ser#: WD-WMAM9SV29648 Type: Hard Disk Supports 48-bit addressing Capacity: 76292.9 MB = 74.5 GB (156247887 x 512) CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. PEX 1: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 Marvell>> printenv baudrate=115200 loads_echo=0 rootpath=/srv/ubuntu netmask=255.255.255.0 run_diag=yes MALLOC_len=1 ethprime=egiga0 bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; lcd0_enable=0 lcd0_params=640x480-16@60 ethmtu=1500 mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no image_multi=yes ethact=egiga0 console=console=ttyS0,115200 bootargs_root=root=/dev/ram0 bootargs_mtd=mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) kernelimage=zImage initrdimage=mfginitrd ipaddr=192.168.1.2 mfgmodel=ix2 preroot_ver=0.0.2 fw_ver=0.0.2 uboot_ver=0.0.8 serial_number=5563Y01001G216000A7J0A1 ethaddr=00:D0:B8:1D:BA:D2 serialNo=EUAC1800AV modelname=31997200 serialno=0,01nrdpRPKLbEh/6nvg5IwLGlVkRu2Q85Gft0N3lR2L2oy1d5RAQiGOzlMCx+zlwdFt,EUAC1800AV, runintime=10800 ftpserver=192.168.43.4 testfile=100M mfgtest_state=system_tested_ok pre_path=IX2/1.0.3/download_runin.sh pre_path_conf=IX2/1.0.3/download_runin.conf pre_serverip=192.168.32.4 pre_user=ixxrunin pre_passwd=123 pre_dirzi=IX2/1.0.3 serverip=192.168.32.4 bootcmd2=ide dev 1;ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x2000; bootm 0x40000 0x900000; bootcmd=setenv bootargs console=ttyS0,115200n8 root=/dev/sda1; usb start; ext2load usb 0:1 0x00800000 /uImage; bootm 0x00800000 stdin=serial stdout=serial stderr=serial mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no enaAutoRecovery=yes pcieTune=no pcieTune1=no Environment size: 1909/4091 bytes
Re: Need help with Lenovo ix2-ng July 17, 2019 10:28PM |
Registered: 5 years ago Posts: 125 |
Re: Need help with Lenovo ix2-ng July 17, 2019 11:43PM |
Admin Registered: 13 years ago Posts: 18,487 |
Quote
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
T T T T T T T T T T T T T T T T T T T T T T T T T T T T T T Device NOT ready
Request Sense returned 00 00 00
T T T T T T T T T T T T T T T T T T T T T T Device NOT ready
Request Sense returned 00 00 00
Re: Need help with Lenovo ix2-ng July 18, 2019 11:06AM |
Registered: 4 years ago Posts: 3 |
Re: Need help with Lenovo ix2-ng July 18, 2019 05:12PM |
Registered: 5 years ago Posts: 125 |