Debian on Iomega EZ Media & Backup Center
Posted by Berryshake
|
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? June 03, 2017 01:01AM |
Admin Registered: 13 years ago Posts: 19,107 |
iomega ez Wrote:
-------------------------------------------------------
>
> I saved by saveenv and I want to check on boot but
> it gives nothing?
Check at serial console. Interrupt u-boot and
You might need to post some more info so that I can show you how to set up fw_printenv in Debian. But serial console should list the envs the same way.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
>
> root@IOMEGA:~# fw_printenv > Cannot access MTD device /dev/mtd1: No such file o > r directory > root@IOMEGA:~# > >>
> I saved by saveenv and I want to check on boot but
> it gives nothing?
Check at serial console. Interrupt u-boot and
printenv
You might need to post some more info so that I can show you how to set up fw_printenv in Debian. But serial console should list the envs the same way.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
iomega ez
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? June 03, 2017 07:12AM |
root@IOMEGA-EZ:/mnt/nas# fw_printenv
Warning: Bad CRC, using default environment
bootargs=
bootcmd=bootp; setenv bootargs root=/dev/nfs nfsroot=${serverip}:${rootpath} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; bootm
bootdelay=3
baudrate=115200
stdin=serial,cros-ec-keyb
stdout=serial,lcd
stderr=serial,lcd
root@IOMEGA-EZ:/mnt/nas#
last time I used my old wheezy usb and this time, I used a new jessi usb and it gives me message.
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix1-spi ** ** uboot_ver:0.0.8 **
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Oct 28 2011 - 15:17:21) Marvell version: 3.6.1 - EMC
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0
Soc: 88F6282 A1 CPU running @ 1200Mhz L2 running @ 600Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 6 tRP = 6 tRAS = 15 tRCD=6
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
[1024kB@f8000000] Flash: 1 MB
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST340014AS Firm: 8.12 Ser#: 5MQ3ESZM
Type: Hard Disk
Supports 48-bit addressing
Capacity: 38146.9 MB = 37.2 GB (78125000 x 512)
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> printenv
baudrate=115200
loads_echo=0
rootpath=/srv/ubuntu
netmask=255.255.255.0
run_diag=yes
MALLOC_len=1
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
lcd0_enable=0
lcd0_params=640x480-16@60
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
image_multi=yes
ethact=egiga0
console=console=ttyS0,115200
bootargs_root=root=/dev/ram0
bootargs_mtd=mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2)
kernelimage=zImage
initrdimage=mfginitrd
ipaddr=192.168.1.2
mfgmodel=ix1
preroot_ver=0.0.2
bootcmd2=ide dev 1;ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x1800; bootm 0x40000 0x900000;
uboot_ver=0.0.8
fw_ver=3.3.2.29823
serial_number=5563Z01001G30100784J0C1
ethaddr=00:D0:B8:14:0B:8A
serialNo=USAD020062
modelname=31997701
serialno=0,01xqV5lWlCJ4voSqhRSkfcpHpi7vDAgRqVwyNe4nzWGO1eGJjRJi8ltftT1y38RqWc,USAD020062,
runintime=10800
ftpserver=192.168.43.4
testfile=100M
mfgtest_state=system_tested_ok
pre_path=IX1/1.0.4/download_runin.sh
pre_path_conf=IX1/1.0.4/download_runin.conf
pre_serverip=192.168.32.4
pre_user=ixxrunin
pre_passwd=123
pre_dirzi=IX1/1.0.4
serverip=192.168.32.4
usb_scan=setenv usb_device 0:1; setenv usb_root sdb1
make_usb_bootargs=setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) root=/dev/$(usb_root) rootdelay=10 rootfstype=ext2
bootcmd1=ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x1800; setenv bootargs $(console) $(bootargs_root) $(bootargs_mtd) $(bootargs_end); bootm 0x40000 0x900000;run bootcmd2
bootcmd=ide reset; run bootcmd_usb; usb stop; run bootcmd1
bootcmd_usb=usb reset; run usb_scan; run make_usb_bootargs; ext2load usb $(usb_device) 0x40000 /boot/uImage; ext2load usb $(usb_device) 0x1100000 /boot/uInitrd; bootm 0x40000 0x1100000
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
pcieTune1=no
Environment size: 2398/4091 bytes
Marvell>>
I used saveenv but if someone do not have access to serial cable, how can I advise them to use my uImage?
|
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? June 03, 2017 02:27PM |
Admin Registered: 13 years ago Posts: 19,107 |
iomega ez,
You are not done yet until you can boot with the rootfs label like this:
And the mtds are not visible in bootlog, so that bootargs_mtd variable seems to have problem. Please get the output of:
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
You are not done yet until you can boot with the rootfs label like this:
make_usb_bootargs=setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) root=LABEL=rootfs rootdelay=10
And the mtds are not visible in bootlog, so that bootargs_mtd variable seems to have problem. Please get the output of:
cat /proc/mtd cat /etc/fw_env.config
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
iomega ez
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? June 03, 2017 06:37PM |
root@IOMEGA-EZ:~# cat /proc/mtd dev: size erasesize name mtd0: 00100000 00010000 "spi0.0" root@IOMEGA-EZ:~# cat /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd0 0xc0000 0x20000 0x20000 root@IOMEGA-EZ:~#
so how should I change uboot ?
|
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? June 03, 2017 06:42PM |
Admin Registered: 13 years ago Posts: 19,107 |
iomega ez,
> so how should I change uboot ?
Power up, interrupt serial console and,
and then
If you can boot all the way into Debian just by doing the above then you can save envs (but don't try anything else). This is to prove that your rootfs was correctly created.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> so how should I change uboot ?
Power up, interrupt serial console and,
setenv make_usb_bootargs 'setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) root=LABEL=rootfs rootdelay=10'
and then
boot
If you can boot all the way into Debian just by doing the above then you can save envs (but don't try anything else). This is to prove that your rootfs was correctly created.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
iomega ez
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? June 03, 2017 07:12PM |
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix1-spi ** ** uboot_ver:0.0.8 **
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Oct 28 2011 - 15:17:21) Marvell version: 3.6.1 - EMC
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0
Soc: 88F6282 A1 CPU running @ 1200Mhz L2 running @ 600Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 6 tRP = 6 tRAS = 15 tRCD=6
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
[1024kB@f8000000] Flash: 1 MB
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST340014AS Firm: 8.12 Ser#: 5MQ3ESZM
Type: Hard Disk
Supports 48-bit addressing
Capacity: 38146.9 MB = 37.2 GB (78125000 x 512)
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> setenv make_usb_bootargs 'setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) root=LABEL=rootfs rootdelay=10'
Marvell>> boot
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST340014AS Firm: 8.12 Ser#: 5MQ3ESZM
Type: Hard Disk
Supports 48-bit addressing
Capacity: 38146.9 MB = 37.2 GB (78125000 x 512)
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
....
................................................................................................................................................................................................................................................................................................................
3167987 bytes read
....
.........................................................................................................................................................................................................................................................................................................................................................................................................................
..............................................................................................................................................................................................................................................................................................
7179935 bytes read
## Booting image at 00040000 ...
Image Name: Linux-4.4.0-kirkwood-tld-1
Created: 2017-06-01 10:40:30 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3167923 Bytes = 3 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
Image Name: initramfs-4.4.0-kirkwood-tld-1
Created: 2016-02-19 7:33:04 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 7179871 Bytes = 6.8 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine model: Lenovo IX2-ng
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) :::DB88FXX81:eth0:none root=LABEL=rootfs rootdelay=10
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 113620K/131072K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 17452K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc07d7ef4 (8000 kB)
[ 0.000000] .init : 0xc07d8000 - 0xc0822000 ( 296 kB)
[ 0.000000] .data : 0xc0822000 - 0xc08b169c ( 574 kB)
[ 0.000000] .bss : 0xc08b169c - 0xc08ff9d0 ( 313 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.000333] Console: colour dummy device 80x30
[ 0.000362] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[ 0.090101] pid_max: default: 32768 minimum: 301
[ 0.090208] Security Framework initialized
[ 0.090282] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090302] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.091088] Initializing cgroup subsys io
[ 0.091121] Initializing cgroup subsys devices
[ 0.091145] Initializing cgroup subsys freezer
[ 0.091178] Initializing cgroup subsys net_cls
[ 0.091259] CPU: Testing write buffer coherency: ok
[ 0.091703] Setting up static identity map for 0x8200 - 0x8258
[ 0.091995] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1
[ 0.095604] devtmpfs: initialized
[ 0.101206] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.101670] prandom: seed boundary self test passed
[ 0.105425] prandom: 100 self tests passed
[ 0.105450] pinctrl core: initialized pinctrl subsystem
[ 0.106814] NET: Registered protocol family 16
[ 0.107258] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.130100] cpuidle: using governor ladder
[ 0.160102] cpuidle: using governor menu
[ 0.160539] Feroceon L2: Enabling L2
[ 0.160580] Feroceon L2: Cache support initialised.
[ 0.160956] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[ 0.166580] No ATAGs?
[ 0.201541] vgaarb: loaded
[ 0.201891] usbcore: registered new interface driver usbfs
[ 0.201969] usbcore: registered new interface driver hub
[ 0.202031] usbcore: registered new device driver usb
[ 0.203134] clocksource: Switched to clocksource orion_clocksource
[ 0.258186] NET: Registered protocol family 2
[ 0.258976] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.259007] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.259031] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.259093] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.259119] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.259315] NET: Registered protocol family 1
[ 0.259709] RPC: Registered named UNIX socket transport module.
[ 0.259721] RPC: Registered udp transport module.
[ 0.259728] RPC: Registered tcp transport module.
[ 0.259735] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.260010] Unpacking initramfs...
[ 0.882153] Freeing initrd memory: 7012K (c1100000 - c17d9000)
[ 0.882310] NetWinder Floating Point Emulator V0.97 (double precision)
[ 0.883462] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.883534] audit: initializing netlink subsys (disabled)
[ 0.883587] audit: type=2000 audit(0.880:1): initialized
[ 0.883933] Initialise system trusted keyring
[ 0.884315] zbud: loaded
[ 0.884598] VFS: Disk quotas dquot_6.6.0
[ 0.884658] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.885194] NFS: Registering the id_resolver key type
[ 0.885231] Key type id_resolver registered
[ 0.885240] Key type id_legacy registered
[ 0.885266] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.885280] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.885499] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 0.886001] Key type big_key registered
[ 0.905236] Key type asymmetric registered
[ 0.905259] Asymmetric key parser 'x509' registered
[ 0.905352] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.905372] io scheduler noop registered
[ 0.905387] io scheduler deadline registered
[ 0.905445] io scheduler cfq registered (default)
[ 0.906776] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 0.907461] irq: Cannot allocate irq_descs @ IRQ35, assuming pre-allocated
[ 0.907885] irq: Cannot allocate irq_descs @ IRQ67, assuming pre-allocated
[ 0.908427] mv_xor f1060800.xor: Marvell shared XOR driver
[ 0.943838] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 0.944088] mv_xor f1060900.xor: Marvell shared XOR driver
[ 0.983840] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 0.984335] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.985646] console [ttyS0] disabled
[ 0.985706] f1012100.serial: ttyS0 at MMIO 0xf1012100 (irq = 27, base_baud = 12500000) is a 16550A
[ 1.588125] console [ttyS0] enabled
[ 1.593571] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
[ 1.604521] libphy: Fixed MDIO Bus: probed
[ 1.608965] libphy: orion_mdio_bus: probed
[ 1.617607] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 1.625750] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:14:0b:8a
[ 1.634740] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.641324] ehci-pci: EHCI PCI platform driver
[ 1.645906] ehci-orion: EHCI orion driver
[ 1.650102] orion-ehci f1050000.ehci: EHCI Host Controller
[ 1.655690] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 1.663571] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000
[ 1.683168] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 1.689421] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.696271] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.703544] usb usb1: Product: EHCI Host Controller
[ 1.708445] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd
[ 1.715105] usb usb1: SerialNumber: f1050000.ehci
[ 1.720549] hub 1-0:1.0: USB hub found
[ 1.724399] hub 1-0:1.0: 1 port detected
[ 1.729307] mousedev: PS/2 mouse device common for all mice
[ 1.735601] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0
[ 1.742676] i2c /dev entries driver
[ 1.748683] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.754549] drop_monitor: Initializing network drop monitor service
[ 1.761101] NET: Registered protocol family 17
[ 1.765857] Key type dns_resolver registered
[ 1.770967] registered taskstats version 1
[ 1.775158] Loading compiled-in X.509 certificates
[ 1.780028] zswap: loaded using pool lzo/zbud
[ 1.792489] Key type encrypted registered
[ 1.797155] rtc-mv f1010300.rtc: setting system clock to 2017-06-04 00:09:55 UTC (1496534995)
[ 1.808269] Freeing unused kernel memory: 296K (c07d8000 - c0822000)
Loading, please wait...
[ 1.881193] systemd-udevd[81]: starting version 215
[ 1.895179] random: systemd-udevd urandom read with 3 bits of entropy available
[ 2.043263] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 2.062009] SCSI subsystem initialized
[ 2.118926] sata_mv f1080000.sata: slots 32 ports 2
[ 2.160542] scsi host0: sata_mv
[ 2.179160] scsi host1: sata_mv
[ 2.182683] ata1: SATA max UDMA/133 irq 34
[ 2.208224] usb 1-1: New USB device found, idVendor=05e3, idProduct=0723
[ 2.215399] ata2: SATA max UDMA/133 irq 34
[ 2.219624] usb 1-1: New USB device strings: Mfr=3, Product=4, SerialNumber=2
[ 2.234665] usb 1-1: Product: USB Storage
[ 2.238720] usb 1-1: Manufacturer: Generic
[ 2.242929] usb 1-1: SerialNumber: 000000009451
[ 2.272041] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 2.279565] usb-storage 1-1:1.0: Quirks match for vid 05e3 pid 0723: 8000
[ 2.286543] scsi host2: usb-storage 1-1:1.0
[ 2.292425] usbcore: registered new interface driver usb-storage
[ 2.301448] usbcore: registered new interface driver uas
[ 2.723176] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F300)
[ 2.763206] ata1.00: ATA-6: ST340014AS, 8.12, max UDMA/133
[ 2.768718] ata1.00: 78125000 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 2.833209] ata1.00: configured for UDMA/133
[ 2.853599] scsi 0:0:0:0: Direct-Access ATA ST340014AS 8.12 PQ: 0 ANSI: 5
[ 3.213169] ata2: SATA link down (SStatus 0 SControl F300)
[ 3.245408] sd 0:0:0:0: [sda] 78125000 512-byte logical blocks: (40.0 GB/37.2 GiB)
[ 3.255729] sd 0:0:0:0: [sda] Write Protect is off
[ 3.260660] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.274811] sda: sda1
[ 3.278890] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.287630] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.294431] scsi 2:0:0:0: Direct-Access Generic STORAGE DEVICE 9451 PQ: 0 ANSI: 0
[ 3.314749] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 3.459380] sd 2:0:0:0: [sdb] 7959552 512-byte logical blocks: (4.07 GB/3.79 GiB)
[ 3.469602] sd 2:0:0:0: [sdb] Write Protect is off
[ 3.476742] sd 2:0:0:0: [sdb] No Caching mode page found
[ 3.482288] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 3.498723] sdb: sdb1
[ 3.512763] sd 2:0:0:0: [sdb] Attached SCSI removable disk
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Checking root file system ... fsck from util-linux 2.25.2
rootfs: clean, 49661/248992 files, 443084/994560 blocks
done.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: udevd[ 15.230963] systemd-udevd[298]: starting version 215
. ok
[....] Synthesizing the initial hotplug events...[ 15.515130] input: gpio-keys as /devices/platform/gpio-keys/input/input0
done.
[....] Waiting for /dev to be fully populated...[ 15.738606] orion_wdt: Initial timeout 21 sec
[ 15.760777] marvell-cesa: probe of f1030000.crypto failed with error -524
[ 15.792668] adt7475 0-002e: ADT7473 device, revision 2
[ 15.839513] random: nonblocking pool is initialized
[ 15.847751] adt7475 0-002e: Bypassing attenuators on: in1
done.
[....] Checking root file system...fsck from util-linux 2.25.2
rootfs: clean, 49661/248992 files, 443084/994560 blocks
done.
[....] Activating lvm and md swap...[ 18.030186] Adding 524284k swap on /swapfile. Priority:-1 extents:225 across:752796k FS
done.
[....] Checking file systems...fsck from util-linux 2.25.2
done.
[ ok ] Loading kernel modules...done.
[ ok ] Cleaning up temporary files... /tmp.
[ 18.824514] EXT4-fs (sda1): mounted filesystem with writeback data mode. Opts: data=writeback
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables ...done.
[ 19.977981] NET: Registered protocol family 10
[ 20.087968] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1
Copyright 2004-2014 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/00:d0:b8:14:0b:8a
Sending on LPF/eth0/00:d0:b8:14:0b:8a
Sending on Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5
[ 23.661024] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 23.670946] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPOFFER from 192.168.2.1
DHCPACK from 192.168.2.1
Reloading /etc/samba/smb.conf: smbd.
bound to 192.168.2.101 -- renewal in 36158 seconds.
done.
[ ok ] Starting rpcbind daemon....
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1258 (syslogd)
. ok
[ ok ] Starting periodic command scheduler: cron.
[ ok ] Starting system message bus: dbus.
[ ok ] Starting the hd-idle daemon: hd-idle.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting NFS common utilities: statd idmapd.
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1256 (klogd)
. ok
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting ftp server: proftpd.
[ ok ] Starting NetBIOS name server: nmbd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[ ok ] Starting SMB/CIFS daemon: smbd.
Debian GNU/Linux 8 IOMEGA-EZ ttyS0
IOMEGA-EZ login:
yes, it boots fine
|
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? June 03, 2017 07:22PM |
Admin Registered: 13 years ago Posts: 19,107 |
Cool!
Now you can save it:
Power up, interrupt serial console and,
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Now you can save it:
Power up, interrupt serial console and,
setenv make_usb_bootargs 'setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) root=LABEL=rootfs rootdelay=10' saveenv
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? June 03, 2017 07:30PM |
Admin Registered: 13 years ago Posts: 19,107 |
Regarding your mtdparts that have not been detected by the kernel. This was one of the reasons you could not use fw_printenv.
Try this,
Power up, interrupt serial console and,
Please post the entire serial boot log here.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Try this,
Power up, interrupt serial console and,
setenv bootargs_mtd 'mtdparts=spi0.0:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2)' boot
Please post the entire serial boot log here.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
iomega ez
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? June 03, 2017 07:35PM |
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix1-spi ** ** uboot_ver:0.0.8 **
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Oct 28 2011 - 15:17:21) Marvell version: 3.6.1 - EMC
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0
Soc: 88F6282 A1 CPU running @ 1200Mhz L2 running @ 600Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 6 tRP = 6 tRAS = 15 tRCD=6
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
[1024kB@f8000000] Flash: 1 MB
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST340014AS Firm: 8.12 Ser#: 5MQ3ESZM
Type: Hard Disk
Supports 48-bit addressing
Capacity: 38146.9 MB = 37.2 GB (78125000 x 512)
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> setenv make_usb_bootargs 'setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) root=LABEL=rootfs rootdelay=10'
Marvell>> saveenv
Saving Environment to Flash...
.
Un-Protected 1 sectors
.
Un-Protected 1 sectors
Erasing Flash...
.
Erased 1 sectors
Writing to Flash... done
.
Protected 1 sectors
.
Protected 1 sectors
Marvell>> boot
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST340014AS Firm: 8.12 Ser#: 5MQ3ESZM
Type: Hard Disk
Supports 48-bit addressing
Capacity: 38146.9 MB = 37.2 GB (78125000 x 512)
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
....
................................................................................................................................................................................................................................................................................................................
3167987 bytes read
....
.........................................................................................................................................................................................................................................................................................................................................................................................................................
..............................................................................................................................................................................................................................................................................................
7179935 bytes read
## Booting image at 00040000 ...
Image Name: Linux-4.4.0-kirkwood-tld-1
Created: 2017-06-01 10:40:30 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3167923 Bytes = 3 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
Image Name: initramfs-4.4.0-kirkwood-tld-1
Created: 2016-02-19 7:33:04 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 7179871 Bytes = 6.8 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine model: Lenovo IX2-ng
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) :::DB88FXX81:eth0:none root=LABEL=rootfs rootdelay=10
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 113620K/131072K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 17452K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc07d7ef4 (8000 kB)
[ 0.000000] .init : 0xc07d8000 - 0xc0822000 ( 296 kB)
[ 0.000000] .data : 0xc0822000 - 0xc08b169c ( 574 kB)
[ 0.000000] .bss : 0xc08b169c - 0xc08ff9d0 ( 313 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.000333] Console: colour dummy device 80x30
[ 0.000362] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[ 0.090101] pid_max: default: 32768 minimum: 301
[ 0.090208] Security Framework initialized
[ 0.090281] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090302] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.091091] Initializing cgroup subsys io
[ 0.091123] Initializing cgroup subsys devices
[ 0.091148] Initializing cgroup subsys freezer
[ 0.091181] Initializing cgroup subsys net_cls
[ 0.091263] CPU: Testing write buffer coherency: ok
[ 0.091707] Setting up static identity map for 0x8200 - 0x8258
[ 0.091999] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1
[ 0.095609] devtmpfs: initialized
[ 0.101208] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.101670] prandom: seed boundary self test passed
[ 0.105425] prandom: 100 self tests passed
[ 0.105451] pinctrl core: initialized pinctrl subsystem
[ 0.106808] NET: Registered protocol family 16
[ 0.107252] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.130100] cpuidle: using governor ladder
[ 0.160102] cpuidle: using governor menu
[ 0.160539] Feroceon L2: Enabling L2
[ 0.160580] Feroceon L2: Cache support initialised.
[ 0.160955] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[ 0.166582] No ATAGs?
[ 0.201540] vgaarb: loaded
[ 0.201891] usbcore: registered new interface driver usbfs
[ 0.201970] usbcore: registered new interface driver hub
[ 0.202031] usbcore: registered new device driver usb
[ 0.203131] clocksource: Switched to clocksource orion_clocksource
[ 0.258199] NET: Registered protocol family 2
[ 0.258984] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.259016] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.259039] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.259101] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.259128] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.259324] NET: Registered protocol family 1
[ 0.259721] RPC: Registered named UNIX socket transport module.
[ 0.259733] RPC: Registered udp transport module.
[ 0.259740] RPC: Registered tcp transport module.
[ 0.259747] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.260021] Unpacking initramfs...
[ 0.882069] Freeing initrd memory: 7012K (c1100000 - c17d9000)
[ 0.882226] NetWinder Floating Point Emulator V0.97 (double precision)
[ 0.883379] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.883453] audit: initializing netlink subsys (disabled)
[ 0.883507] audit: type=2000 audit(0.880:1): initialized
[ 0.883856] Initialise system trusted keyring
[ 0.884242] zbud: loaded
[ 0.884524] VFS: Disk quotas dquot_6.6.0
[ 0.884583] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.885118] NFS: Registering the id_resolver key type
[ 0.885155] Key type id_resolver registered
[ 0.885165] Key type id_legacy registered
[ 0.885190] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.885204] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.885424] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 0.885927] Key type big_key registered
[ 0.905175] Key type asymmetric registered
[ 0.905197] Asymmetric key parser 'x509' registered
[ 0.905290] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.905310] io scheduler noop registered
[ 0.905326] io scheduler deadline registered
[ 0.905384] io scheduler cfq registered (default)
[ 0.906714] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 0.907396] irq: Cannot allocate irq_descs @ IRQ35, assuming pre-allocated
[ 0.907820] irq: Cannot allocate irq_descs @ IRQ67, assuming pre-allocated
[ 0.908364] mv_xor f1060800.xor: Marvell shared XOR driver
[ 0.943838] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 0.944087] mv_xor f1060900.xor: Marvell shared XOR driver
[ 0.983835] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 0.984332] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.985644] console [ttyS0] disabled
[ 0.985708] f1012100.serial: ttyS0 at MMIO 0xf1012100 (irq = 27, base_baud = 12500000) is a 16550A
[ 1.588126] console [ttyS0] enabled
[ 1.593564] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
[ 1.604507] libphy: Fixed MDIO Bus: probed
[ 1.608949] libphy: orion_mdio_bus: probed
[ 1.617611] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 1.625748] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:14:0b:8a
[ 1.634743] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.641325] ehci-pci: EHCI PCI platform driver
[ 1.645907] ehci-orion: EHCI orion driver
[ 1.650106] orion-ehci f1050000.ehci: EHCI Host Controller
[ 1.655693] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 1.663578] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000
[ 1.683166] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 1.689423] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.696272] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.703545] usb usb1: Product: EHCI Host Controller
[ 1.708446] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd
[ 1.715106] usb usb1: SerialNumber: f1050000.ehci
[ 1.720557] hub 1-0:1.0: USB hub found
[ 1.724400] hub 1-0:1.0: 1 port detected
[ 1.729307] mousedev: PS/2 mouse device common for all mice
[ 1.735605] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0
[ 1.742678] i2c /dev entries driver
[ 1.748682] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.754552] drop_monitor: Initializing network drop monitor service
[ 1.761100] NET: Registered protocol family 17
[ 1.765857] Key type dns_resolver registered
[ 1.770966] registered taskstats version 1
[ 1.775159] Loading compiled-in X.509 certificates
[ 1.780029] zswap: loaded using pool lzo/zbud
[ 1.792490] Key type encrypted registered
[ 1.797152] rtc-mv f1010300.rtc: setting system clock to 2017-06-04 00:28:48 UTC (1496536128)
[ 1.808258] Freeing unused kernel memory: 296K (c07d8000 - c0822000)
Loading, please wait...
[ 1.881346] systemd-udevd[81]: starting version 215
[ 1.895249] random: systemd-udevd urandom read with 3 bits of entropy available
[ 2.043272] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 2.065944] SCSI subsystem initialized
[ 2.122023] sata_mv f1080000.sata: slots 32 ports 2
[ 2.162732] scsi host0: sata_mv
[ 2.181162] scsi host1: sata_mv
[ 2.190420] ata1: SATA max UDMA/133 irq 34
[ 2.207183] ata2: SATA max UDMA/133 irq 34
[ 2.212228] usb 1-1: New USB device found, idVendor=05e3, idProduct=0723
[ 2.223237] usb 1-1: New USB device strings: Mfr=3, Product=4, SerialNumber=2
[ 2.230424] usb 1-1: Product: USB Storage
[ 2.246635] usb 1-1: Manufacturer: Generic
[ 2.250849] usb 1-1: SerialNumber: 000000009451
[ 2.271232] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 2.278712] usb-storage 1-1:1.0: Quirks match for vid 05e3 pid 0723: 8000
[ 2.285688] scsi host2: usb-storage 1-1:1.0
[ 2.291577] usbcore: registered new interface driver usb-storage
[ 2.300588] usbcore: registered new interface driver uas
[ 2.753174] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F300)
[ 2.793202] ata1.00: ATA-6: ST340014AS, 8.12, max UDMA/133
[ 2.798716] ata1.00: 78125000 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 2.843381] ata1.00: configured for UDMA/133
[ 2.863598] scsi 0:0:0:0: Direct-Access ATA ST340014AS 8.12 PQ: 0 ANSI: 5
[ 3.223166] ata2: SATA link down (SStatus 0 SControl F300)
[ 3.255548] sd 0:0:0:0: [sda] 78125000 512-byte logical blocks: (40.0 GB/37.2 GiB)
[ 3.265852] sd 0:0:0:0: [sda] Write Protect is off
[ 3.270785] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.285040] scsi 2:0:0:0: Direct-Access Generic STORAGE DEVICE 9451 PQ: 0 ANSI: 0
[ 3.293411] sda: sda1
[ 3.297691] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.310165] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.316062] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 3.444630] sd 2:0:0:0: [sdb] 7959552 512-byte logical blocks: (4.07 GB/3.79 GiB)
[ 3.453242] sd 2:0:0:0: [sdb] Write Protect is off
[ 3.459108] sd 2:0:0:0: [sdb] No Caching mode page found
[ 3.464476] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 3.478719] sdb: sdb1
[ 3.491885] sd 2:0:0:0: [sdb] Attached SCSI removable disk
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Checking root file system ... fsck from util-linux 2.25.2
rootfs: clean, 49671/248992 files, 443092/994560 blocks
done.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: udevd[ 15.354038] systemd-udevd[299]: starting version 215
. ok
[....] Synthesizing the initial hotplug events...[ 15.624772] input: gpio-keys as /devices/platform/gpio-keys/input/input0
done.
[....] Waiting for /dev to be fully populated...[ 15.826583] adt7475 0-002e: ADT7473 device, revision 2
[ 15.852394] adt7475 0-002e: Bypassing attenuators on: in1
[ 15.883722] orion_wdt: Initial timeout 21 sec
[ 15.921651] marvell-cesa: probe of f1030000.crypto failed with error -524
[ 15.970611] random: nonblocking pool is initialized
done.
[....] Checking root file system...fsck from util-linux 2.25.2
rootfs: clean, 49671/248992 files, 443092/994560 blocks
done.
[....] Activating lvm and md swap...[ 18.058559] Adding 524284k swap on /swapfile. Priority:-1 extents:225 across:752796k FS
done.
[....] Checking file systems...fsck from util-linux 2.25.2
done.
[ ok ] Loading kernel modules...done.
[ ok ] Cleaning up temporary files... /tmp.
[ 18.834519] EXT4-fs (sda1): mounted filesystem with writeback data mode. Opts: data=writeback
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables ...done.
[ 19.980294] NET: Registered protocol family 10
[ 20.087356] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1
Copyright 2004-2014 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/00:d0:b8:14:0b:8a
Sending on LPF/eth0/00:d0:b8:14:0b:8a
Sending on Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7
[ 23.683654] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 23.693575] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPOFFER from 192.168.2.1
DHCPACK from 192.168.2.1
Reloading /etc/samba/smb.conf: smbd.
bound to 192.168.2.101 -- renewal in 32952 seconds.
done.
[ ok ] Starting rpcbind daemon....
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1259 (syslogd)
. ok
[ ok ] Starting periodic command scheduler: cron.
[ ok ] Starting system message bus: dbus.
[ ok ] Starting the hd-idle daemon: hd-idle.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting NFS common utilities: statd idmapd.
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1257 (klogd)
. ok
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting ftp server: proftpd.
[ ok ] Starting NetBIOS name server: nmbd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[ ok ] Starting SMB/CIFS daemon: smbd.
Debian GNU/Linux 8 IOMEGA-EZ ttyS0
IOMEGA-EZ login:
done
root@IOMEGA-EZ:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00100000 00010000 "spi0.0"
root@IOMEGA-EZ:~# cat /etc/fw_env.config
# MTD device name Device offset Env. size Flash sector size Number of sectors
/dev/mtd0 0xc0000 0x20000 0x20000
root@IOMEGA-EZ:~# fw_printenv
Warning: Bad CRC, using default environment
bootargs=
bootcmd=bootp; setenv bootargs root=/dev/nfs nfsroot=${serverip}:${rootpath} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; bootm
bootdelay=3
baudrate=115200
stdin=serial,cros-ec-keyb
stdout=serial,lcd
stderr=serial,lcd
root@IOMEGA-EZ:~#
still have the same output?
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix1-spi ** ** uboot_ver:0.0.8 **
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Oct 28 2011 - 15:17:21) Marvell version: 3.6.1 - EMC
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0
Soc: 88F6282 A1 CPU running @ 1200Mhz L2 running @ 600Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 6 tRP = 6 tRAS = 15 tRCD=6
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
[1024kB@f8000000] Flash: 1 MB
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST340014AS Firm: 8.12 Ser#: 5MQ3ESZM
Type: Hard Disk
Supports 48-bit addressing
Capacity: 38146.9 MB = 37.2 GB (78125000 x 512)
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> printenv
baudrate=115200
loads_echo=0
rootpath=/srv/ubuntu
netmask=255.255.255.0
run_diag=yes
MALLOC_len=1
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
lcd0_enable=0
lcd0_params=640x480-16@60
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
image_multi=yes
ethact=egiga0
console=console=ttyS0,115200
bootargs_root=root=/dev/ram0
bootargs_mtd=mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2)
kernelimage=zImage
initrdimage=mfginitrd
ipaddr=192.168.1.2
mfgmodel=ix1
preroot_ver=0.0.2
bootcmd2=ide dev 1;ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x1800; bootm 0x40000 0x900000;
uboot_ver=0.0.8
fw_ver=3.3.2.29823
serial_number=5563Z01001G30100784J0C1
ethaddr=00:D0:B8:14:0B:8A
serialNo=USAD020062
modelname=31997701
serialno=0,01xqV5lWlCJ4voSqhRSkfcpHpi7vDAgRqVwyNe4nzWGO1eGJjRJi8ltftT1y38RqWc,USAD020062,
runintime=10800
ftpserver=192.168.43.4
testfile=100M
mfgtest_state=system_tested_ok
pre_path=IX1/1.0.4/download_runin.sh
pre_path_conf=IX1/1.0.4/download_runin.conf
pre_serverip=192.168.32.4
pre_user=ixxrunin
pre_passwd=123
pre_dirzi=IX1/1.0.4
serverip=192.168.32.4
usb_scan=setenv usb_device 0:1; setenv usb_root sdb1
bootcmd1=ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x1800; setenv bootargs $(console) $(bootargs_root) $(bootargs_mtd) $(bootargs_end); bootm 0x40000 0x900000;run bootcmd2
bootcmd=ide reset; run bootcmd_usb; usb stop; run bootcmd1
bootcmd_usb=usb reset; run usb_scan; run make_usb_bootargs; ext2load usb $(usb_device) 0x40000 /boot/uImage; ext2load usb $(usb_device) 0x1100000 /boot/uInitrd; bootm 0x40000 0x1100000
make_usb_bootargs=setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) root=LABEL=rootfs rootdelay=10
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
pcieTune1=no
Environment size: 2378/4091 bytes
Marvell>>
here is printenv output
|
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? June 03, 2017 08:13PM |
Admin Registered: 13 years ago Posts: 19,107 |
See this above
http://forum.doozan.com/read.php?2,15887,34543#msg-34543
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
http://forum.doozan.com/read.php?2,15887,34543#msg-34543
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
iomega ez
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? June 04, 2017 04:47AM |
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix1-spi ** ** uboot_ver:0.0.8 **
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Oct 28 2011 - 15:17:21) Marvell version: 3.6.1 - EMC
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0
Soc: 88F6282 A1 CPU running @ 1200Mhz L2 running @ 600Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 6 tRP = 6 tRAS = 15 tRCD=6
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
[1024kB@f8000000] Flash: 1 MB
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST340014AS Firm: 8.12 Ser#: 5MQ3ESZM
Type: Hard Disk
Supports 48-bit addressing
Capacity: 38146.9 MB = 37.2 GB (78125000 x 512)
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> printenv
baudrate=115200
loads_echo=0
rootpath=/srv/ubuntu
netmask=255.255.255.0
run_diag=yes
MALLOC_len=1
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
lcd0_enable=0
lcd0_params=640x480-16@60
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
image_multi=yes
ethact=egiga0
console=console=ttyS0,115200
bootargs_root=root=/dev/ram0
bootargs_mtd=mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2)
kernelimage=zImage
initrdimage=mfginitrd
ipaddr=192.168.1.2
mfgmodel=ix1
preroot_ver=0.0.2
bootcmd2=ide dev 1;ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x1800; bootm 0x40000 0x900000;
uboot_ver=0.0.8
fw_ver=3.3.2.29823
serial_number=5563Z01001G30100784J0C1
ethaddr=00:D0:B8:14:0B:8A
serialNo=USAD020062
modelname=31997701
serialno=0,01xqV5lWlCJ4voSqhRSkfcpHpi7vDAgRqVwyNe4nzWGO1eGJjRJi8ltftT1y38RqWc,USAD020062,
runintime=10800
ftpserver=192.168.43.4
testfile=100M
mfgtest_state=system_tested_ok
pre_path=IX1/1.0.4/download_runin.sh
pre_path_conf=IX1/1.0.4/download_runin.conf
pre_serverip=192.168.32.4
pre_user=ixxrunin
pre_passwd=123
pre_dirzi=IX1/1.0.4
serverip=192.168.32.4
usb_scan=setenv usb_device 0:1; setenv usb_root sdb1
bootcmd1=ide read 0x40000 0x800 0x1800; ide read 0x900000 0x2000 0x1800; setenv bootargs $(console) $(bootargs_root) $(bootargs_mtd) $(bootargs_end); bootm 0x40000 0x900000;run bootcmd2
bootcmd=ide reset; run bootcmd_usb; usb stop; run bootcmd1
bootcmd_usb=usb reset; run usb_scan; run make_usb_bootargs; ext2load usb $(usb_device) 0x40000 /boot/uImage; ext2load usb $(usb_device) 0x1100000 /boot/uInitrd; bootm 0x40000 0x1100000
make_usb_bootargs=setenv bootargs $(console) $(bootargs_mtd) $(bootargs_end) root=LABEL=rootfs rootdelay=10
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
pcieTune1=no
Environment size: 2378/4091 bytes
Marvell>> boot
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST340014AS Firm: 8.12 Ser#: 5MQ3ESZM
Type: Hard Disk
Supports 48-bit addressing
Capacity: 38146.9 MB = 37.2 GB (78125000 x 512)
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
....
................................................................................................................................................................................................................................................................................................................
3167987 bytes read
....
.........................................................................................................................................................................................................................................................................................................................................................................................................................
..............................................................................................................................................................................................................................................................................................
7179935 bytes read
## Booting image at 00040000 ...
Image Name: Linux-4.4.0-kirkwood-tld-1
Created: 2017-06-01 10:40:30 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3167923 Bytes = 3 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
Image Name: initramfs-4.4.0-kirkwood-tld-1
Created: 2016-02-19 7:33:04 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 7179871 Bytes = 6.8 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine model: Lenovo IX2-ng
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=spi_flash:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) :::DB88FXX81:eth0:none root=LABEL=rootfs rootdelay=10
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 113620K/131072K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 17452K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc07d7ef4 (8000 kB)
[ 0.000000] .init : 0xc07d8000 - 0xc0822000 ( 296 kB)
[ 0.000000] .data : 0xc0822000 - 0xc08b169c ( 574 kB)
[ 0.000000] .bss : 0xc08b169c - 0xc08ff9d0 ( 313 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.000333] Console: colour dummy device 80x30
[ 0.000362] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[ 0.090101] pid_max: default: 32768 minimum: 301
[ 0.090208] Security Framework initialized
[ 0.090281] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090302] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.091088] Initializing cgroup subsys io
[ 0.091121] Initializing cgroup subsys devices
[ 0.091145] Initializing cgroup subsys freezer
[ 0.091178] Initializing cgroup subsys net_cls
[ 0.091259] CPU: Testing write buffer coherency: ok
[ 0.091703] Setting up static identity map for 0x8200 - 0x8258
[ 0.091995] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1
[ 0.095604] devtmpfs: initialized
[ 0.101206] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.101670] prandom: seed boundary self test passed
[ 0.105425] prandom: 100 self tests passed
[ 0.105450] pinctrl core: initialized pinctrl subsystem
[ 0.106814] NET: Registered protocol family 16
[ 0.107257] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.130099] cpuidle: using governor ladder
[ 0.160101] cpuidle: using governor menu
[ 0.160544] Feroceon L2: Enabling L2
[ 0.160584] Feroceon L2: Cache support initialised.
[ 0.160959] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[ 0.166585] No ATAGs?
[ 0.201539] vgaarb: loaded
[ 0.201890] usbcore: registered new interface driver usbfs
[ 0.201969] usbcore: registered new interface driver hub
[ 0.202030] usbcore: registered new device driver usb
[ 0.203137] clocksource: Switched to clocksource orion_clocksource
[ 0.258198] NET: Registered protocol family 2
[ 0.258988] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.259019] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.259042] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.259104] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.259130] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.259323] NET: Registered protocol family 1
[ 0.259720] RPC: Registered named UNIX socket transport module.
[ 0.259731] RPC: Registered udp transport module.
[ 0.259739] RPC: Registered tcp transport module.
[ 0.259746] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.260018] Unpacking initramfs...
[ 0.882184] Freeing initrd memory: 7012K (c1100000 - c17d9000)
[ 0.882340] NetWinder Floating Point Emulator V0.97 (double precision)
[ 0.883500] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.883573] audit: initializing netlink subsys (disabled)
[ 0.883624] audit: type=2000 audit(0.880:1): initialized
[ 0.883973] Initialise system trusted keyring
[ 0.884359] zbud: loaded
[ 0.884643] VFS: Disk quotas dquot_6.6.0
[ 0.884703] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.885238] NFS: Registering the id_resolver key type
[ 0.885280] Key type id_resolver registered
[ 0.885290] Key type id_legacy registered
[ 0.885315] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.885329] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.885547] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 0.886050] Key type big_key registered
[ 0.905304] Key type asymmetric registered
[ 0.905326] Asymmetric key parser 'x509' registered
[ 0.905419] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.905438] io scheduler noop registered
[ 0.905454] io scheduler deadline registered
[ 0.905511] io scheduler cfq registered (default)
[ 0.906842] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 0.907524] irq: Cannot allocate irq_descs @ IRQ35, assuming pre-allocated
[ 0.907947] irq: Cannot allocate irq_descs @ IRQ67, assuming pre-allocated
[ 0.908490] mv_xor f1060800.xor: Marvell shared XOR driver
[ 0.943841] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 0.944088] mv_xor f1060900.xor: Marvell shared XOR driver
[ 0.983838] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 0.984334] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.985644] console [ttyS0] disabled
[ 0.985707] f1012100.serial: ttyS0 at MMIO 0xf1012100 (irq = 27, base_baud = 12500000) is a 16550A
[ 1.588123] console [ttyS0] enabled
[ 1.593563] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
[ 1.604494] libphy: Fixed MDIO Bus: probed
[ 1.608941] libphy: orion_mdio_bus: probed
[ 1.617635] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 1.625763] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:14:0b:8a
[ 1.634758] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.641340] ehci-pci: EHCI PCI platform driver
[ 1.645921] ehci-orion: EHCI orion driver
[ 1.650119] orion-ehci f1050000.ehci: EHCI Host Controller
[ 1.655710] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 1.663578] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000
[ 1.683170] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 1.689429] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.696280] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.703552] usb usb1: Product: EHCI Host Controller
[ 1.708453] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd
[ 1.715113] usb usb1: SerialNumber: f1050000.ehci
[ 1.720559] hub 1-0:1.0: USB hub found
[ 1.724408] hub 1-0:1.0: 1 port detected
[ 1.729314] mousedev: PS/2 mouse device common for all mice
[ 1.735609] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0
[ 1.742685] i2c /dev entries driver
[ 1.748679] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.754549] drop_monitor: Initializing network drop monitor service
[ 1.761098] NET: Registered protocol family 17
[ 1.765856] Key type dns_resolver registered
[ 1.770961] registered taskstats version 1
[ 1.775157] Loading compiled-in X.509 certificates
[ 1.780027] zswap: loaded using pool lzo/zbud
[ 1.792479] Key type encrypted registered
[ 1.797140] rtc-mv f1010300.rtc: setting system clock to 2017-06-04 00:33:34 UTC (1496536414)
[ 1.808251] Freeing unused kernel memory: 296K (c07d8000 - c0822000)
Loading, please wait...
[ 1.880881] systemd-udevd[81]: starting version 215
[ 1.895215] random: systemd-udevd urandom read with 3 bits of entropy available
[ 2.043274] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 2.067148] SCSI subsystem initialized
[ 2.117277] sata_mv f1080000.sata: slots 32 ports 2
[ 2.160500] scsi host0: sata_mv
[ 2.180713] scsi host1: sata_mv
[ 2.187683] ata1: SATA max UDMA/133 irq 34
[ 2.191828] ata2: SATA max UDMA/133 irq 34
[ 2.208232] usb 1-1: New USB device found, idVendor=05e3, idProduct=0723
[ 2.220043] usb 1-1: New USB device strings: Mfr=3, Product=4, SerialNumber=2
[ 2.234983] usb 1-1: Product: USB Storage
[ 2.239043] usb 1-1: Manufacturer: Generic
[ 2.251231] usb 1-1: SerialNumber: 000000009451
[ 2.272085] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 2.279608] usb-storage 1-1:1.0: Quirks match for vid 05e3 pid 0723: 8000
[ 2.286586] scsi host2: usb-storage 1-1:1.0
[ 2.292478] usbcore: registered new interface driver usb-storage
[ 2.301505] usbcore: registered new interface driver uas
[ 2.753178] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F300)
[ 2.793206] ata1.00: ATA-6: ST340014AS, 8.12, max UDMA/133
[ 2.798724] ata1.00: 78125000 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 2.863210] ata1.00: configured for UDMA/133
[ 2.883595] scsi 0:0:0:0: Direct-Access ATA ST340014AS 8.12 PQ: 0 ANSI: 5
[ 3.243171] ata2: SATA link down (SStatus 0 SControl F300)
[ 3.275680] sd 0:0:0:0: [sda] 78125000 512-byte logical blocks: (40.0 GB/37.2 GiB)
[ 3.286570] sd 0:0:0:0: [sda] Write Protect is off
[ 3.291676] scsi 2:0:0:0: Direct-Access Generic STORAGE DEVICE 9451 PQ: 0 ANSI: 0
[ 3.300001] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.319083] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.324700] sda: sda1
[ 3.328961] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.334026] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 3.456754] sd 2:0:0:0: [sdb] 7959552 512-byte logical blocks: (4.07 GB/3.79 GiB)
[ 3.465362] sd 2:0:0:0: [sdb] Write Protect is off
[ 3.471236] sd 2:0:0:0: [sdb] No Caching mode page found
[ 3.476600] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 3.490844] sdb: sdb1
[ 3.504014] sd 2:0:0:0: [sdb] Attached SCSI removable disk
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Checking root file system ... fsck from util-linux 2.25.2
rootfs: clean, 49671/248992 files, 443094/994560 blocks
done.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: udevd[ 15.334064] systemd-udevd[299]: starting version 215
. ok
[....] Synthesizing the initial hotplug events...[ 15.585510] input: gpio-keys as /devices/platform/gpio-keys/input/input0
done.
[....] Waiting for /dev to be fully populated...[ 15.802619] adt7475 0-002e: ADT7473 device, revision 2
[ 15.850649] adt7475 0-002e: Bypassing attenuators on: in1
[ 15.864544] orion_wdt: Initial timeout 21 sec
[ 15.896435] marvell-cesa: probe of f1030000.crypto failed with error -524
[ 15.950080] random: nonblocking pool is initialized
done.
[....] Checking root file system...fsck from util-linux 2.25.2
rootfs: clean, 49671/248992 files, 443094/994560 blocks
done.
[....] Activating lvm and md swap...[ 18.280053] Adding 524284k swap on /swapfile. Priority:-1 extents:225 across:752796k FS
done.
[....] Checking file systems...fsck from util-linux 2.25.2
done.
[ ok ] Loading kernel modules...done.
[ ok ] Cleaning up temporary files... /tmp.
[ 19.094475] EXT4-fs (sda1): mounted filesystem with writeback data mode. Opts: data=writeback
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables ...done.
[ 20.247675] NET: Registered protocol family 10
[ 20.357368] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1
Copyright 2004-2014 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/00:d0:b8:14:0b:8a
Sending on LPF/eth0/00:d0:b8:14:0b:8a
Sending on Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4
[ 23.868760] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 23.878692] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPOFFER from 192.168.2.1
DHCPACK from 192.168.2.1
Reloading /etc/samba/smb.conf: smbd.
bound to 192.168.2.101 -- renewal in 38961 seconds.
done.
[ ok ] Starting rpcbind daemon....
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1259 (syslogd)
. ok
[ ok ] Starting periodic command scheduler: cron.
[ ok ] Starting system message bus: dbus.
[ ok ] Starting the hd-idle daemon: hd-idle.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting NFS common utilities: statd idmapd.
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1257 (klogd)
. ok
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting ftp server: proftpd.
[ ok ] Starting NetBIOS name server: nmbd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[ ok ] Starting SMB/CIFS daemon: smbd.
Debian GNU/Linux 8 IOMEGA-EZ ttyS0
IOMEGA-EZ login:
here it is
|
iomega ez
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? June 04, 2017 04:51AM |
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix1-spi ** ** uboot_ver:0.0.8 **
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Oct 28 2011 - 15:17:21) Marvell version: 3.6.1 - EMC
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0
Soc: 88F6282 A1 CPU running @ 1200Mhz L2 running @ 600Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 6 tRP = 6 tRAS = 15 tRCD=6
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
[1024kB@f8000000] Flash: 1 MB
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST340014AS Firm: 8.12 Ser#: 5MQ3ESZM
Type: Hard Disk
Supports 48-bit addressing
Capacity: 38146.9 MB = 37.2 GB (78125000 x 512)
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> setenv bootargs_mtd 'mtdparts=spi0.0:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2)'
Marvell>> boot
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: ST340014AS Firm: 8.12 Ser#: 5MQ3ESZM
Type: Hard Disk
Supports 48-bit addressing
Capacity: 38146.9 MB = 37.2 GB (78125000 x 512)
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
....
................................................................................................................................................................................................................................................................................................................
3167987 bytes read
....
.........................................................................................................................................................................................................................................................................................................................................................................................................................
..............................................................................................................................................................................................................................................................................................
7179935 bytes read
## Booting image at 00040000 ...
Image Name: Linux-4.4.0-kirkwood-tld-1
Created: 2017-06-01 10:40:30 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3167923 Bytes = 3 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
Image Name: initramfs-4.4.0-kirkwood-tld-1
Created: 2016-02-19 7:33:04 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 7179871 Bytes = 6.8 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine model: Lenovo IX2-ng
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=spi0.0:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2) :::DB88FXX81:eth0:none root=LABEL=rootfs rootdelay=10
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 113620K/131072K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 17452K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc07d7ef4 (8000 kB)
[ 0.000000] .init : 0xc07d8000 - 0xc0822000 ( 296 kB)
[ 0.000000] .data : 0xc0822000 - 0xc08b169c ( 574 kB)
[ 0.000000] .bss : 0xc08b169c - 0xc08ff9d0 ( 313 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.000333] Console: colour dummy device 80x30
[ 0.000362] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[ 0.090101] pid_max: default: 32768 minimum: 301
[ 0.090204] Security Framework initialized
[ 0.090276] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090296] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.091078] Initializing cgroup subsys io
[ 0.091111] Initializing cgroup subsys devices
[ 0.091135] Initializing cgroup subsys freezer
[ 0.091167] Initializing cgroup subsys net_cls
[ 0.091249] CPU: Testing write buffer coherency: ok
[ 0.091693] Setting up static identity map for 0x8200 - 0x8258
[ 0.091986] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1
[ 0.095595] devtmpfs: initialized
[ 0.101183] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.101644] prandom: seed boundary self test passed
[ 0.105399] prandom: 100 self tests passed
[ 0.105425] pinctrl core: initialized pinctrl subsystem
[ 0.106792] NET: Registered protocol family 16
[ 0.107236] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.130101] cpuidle: using governor ladder
[ 0.160099] cpuidle: using governor menu
[ 0.160542] Feroceon L2: Enabling L2
[ 0.160583] Feroceon L2: Cache support initialised.
[ 0.160958] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[ 0.166581] No ATAGs?
[ 0.201535] vgaarb: loaded
[ 0.201888] usbcore: registered new interface driver usbfs
[ 0.201966] usbcore: registered new interface driver hub
[ 0.202026] usbcore: registered new device driver usb
[ 0.203131] clocksource: Switched to clocksource orion_clocksource
[ 0.258203] NET: Registered protocol family 2
[ 0.258995] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.259027] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.259050] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.259112] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.259138] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.259331] NET: Registered protocol family 1
[ 0.259729] RPC: Registered named UNIX socket transport module.
[ 0.259741] RPC: Registered udp transport module.
[ 0.259748] RPC: Registered tcp transport module.
[ 0.259756] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.260030] Unpacking initramfs...
[ 0.882257] Freeing initrd memory: 7012K (c1100000 - c17d9000)
[ 0.882412] NetWinder Floating Point Emulator V0.97 (double precision)
[ 0.883564] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.883638] audit: initializing netlink subsys (disabled)
[ 0.883691] audit: type=2000 audit(0.880:1): initialized
[ 0.884038] Initialise system trusted keyring
[ 0.884425] zbud: loaded
[ 0.884713] VFS: Disk quotas dquot_6.6.0
[ 0.884774] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.885302] NFS: Registering the id_resolver key type
[ 0.885340] Key type id_resolver registered
[ 0.885349] Key type id_legacy registered
[ 0.885374] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.885388] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.885607] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 0.886109] Key type big_key registered
[ 0.905354] Key type asymmetric registered
[ 0.905376] Asymmetric key parser 'x509' registered
[ 0.905468] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.905489] io scheduler noop registered
[ 0.905504] io scheduler deadline registered
[ 0.905562] io scheduler cfq registered (default)
[ 0.906895] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 0.907577] irq: Cannot allocate irq_descs @ IRQ35, assuming pre-allocated
[ 0.908000] irq: Cannot allocate irq_descs @ IRQ67, assuming pre-allocated
[ 0.908543] mv_xor f1060800.xor: Marvell shared XOR driver
[ 0.943839] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 0.944086] mv_xor f1060900.xor: Marvell shared XOR driver
[ 0.983835] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 0.984334] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.985645] console [ttyS0] disabled
[ 0.985708] f1012100.serial: ttyS0 at MMIO 0xf1012100 (irq = 27, base_baud = 12500000) is a 16550A
[ 1.587860] console [ttyS0] enabled
[ 1.593304] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
[ 1.598138] 3 cmdlinepart partitions found on MTD device spi0.0
[ 1.604118] Creating 3 MTD partitions on "spi0.0":
[ 1.608932] 0x000000000000-0x00000007e000 : "u-boot"
[ 1.613933] mtd: partition "u-boot" doesn't end on an erase block -- force read-only
[ 1.622936] 0x00000007f000-0x000000080000 : "env"
[ 1.627717] mtd: partition "env" doesn't start on an erase block boundary -- force read-only
[ 1.637403] 0x00000007e000-0x00000007f000 : "env2"
[ 1.642221] mtd: partition "env2" doesn't start on an erase block boundary -- force read-only
[ 1.652959] libphy: Fixed MDIO Bus: probed
[ 1.657462] libphy: orion_mdio_bus: probed
[ 1.666228] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 1.674322] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:b8:14:0b:8a
[ 1.683275] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.689857] ehci-pci: EHCI PCI platform driver
[ 1.694485] ehci-orion: EHCI orion driver
[ 1.698686] orion-ehci f1050000.ehci: EHCI Host Controller
[ 1.704280] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 1.712207] orion-ehci f1050000.ehci: irq 31, io mem 0xf1050000
[ 1.733152] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 1.739396] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.746243] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.753516] usb usb1: Product: EHCI Host Controller
[ 1.758416] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd
[ 1.765077] usb usb1: SerialNumber: f1050000.ehci
[ 1.770565] hub 1-0:1.0: USB hub found
[ 1.774414] hub 1-0:1.0: 1 port detected
[ 1.779306] mousedev: PS/2 mouse device common for all mice
[ 1.785573] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0
[ 1.792641] i2c /dev entries driver
[ 1.798530] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.804405] drop_monitor: Initializing network drop monitor service
[ 1.810943] NET: Registered protocol family 17
[ 1.815705] Key type dns_resolver registered
[ 1.820827] registered taskstats version 1
[ 1.825025] Loading compiled-in X.509 certificates
[ 1.829901] zswap: loaded using pool lzo/zbud
[ 1.842384] Key type encrypted registered
[ 1.847042] rtc-mv f1010300.rtc: setting system clock to 2017-06-04 09:44:00 UTC (1496569440)
[ 1.858146] Freeing unused kernel memory: 296K (c07d8000 - c0822000)
Loading, please wait...
[ 1.931099] systemd-udevd[82]: starting version 215
[ 1.945207] random: systemd-udevd urandom read with 3 bits of entropy available
[ 2.093232] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 2.111933] SCSI subsystem initialized
[ 2.177545] sata_mv f1080000.sata: slots 32 ports 2
[ 2.218511] scsi host0: sata_mv
[ 2.233319] scsi host1: sata_mv
[ 2.246859] ata1: SATA max UDMA/133 irq 34
[ 2.250985] ata2: SATA max UDMA/133 irq 34
[ 2.268234] usb 1-1: New USB device found, idVendor=05e3, idProduct=0723
[ 2.280435] usb 1-1: New USB device strings: Mfr=3, Product=4, SerialNumber=2
[ 2.294277] usb 1-1: Product: USB Storage
[ 2.298316] usb 1-1: Manufacturer: Generic
[ 2.302542] usb 1-1: SerialNumber: 000000009451
[ 2.332262] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 2.339740] usb-storage 1-1:1.0: Quirks match for vid 05e3 pid 0723: 8000
[ 2.346800] scsi host2: usb-storage 1-1:1.0
[ 2.352703] usbcore: registered new interface driver usb-storage
[ 2.361693] usbcore: registered new interface driver uas
[ 2.813173] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F300)
[ 2.853200] ata1.00: ATA-6: ST340014AS, 8.12, max UDMA/133
[ 2.858716] ata1.00: 78125000 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 2.923204] ata1.00: configured for UDMA/133
[ 2.943607] scsi 0:0:0:0: Direct-Access ATA ST340014AS 8.12 PQ: 0 ANSI: 5
[ 3.303170] ata2: SATA link down (SStatus 0 SControl F300)
[ 3.335605] sd 0:0:0:0: [sda] 78125000 512-byte logical blocks: (40.0 GB/37.2 GiB)
[ 3.346466] sd 0:0:0:0: [sda] Write Protect is off
[ 3.351535] scsi 2:0:0:0: Direct-Access Generic STORAGE DEVICE 9451 PQ: 0 ANSI: 0
[ 3.359913] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.379144] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.384733] sda: sda1
[ 3.389022] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.394089] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 3.515883] sd 2:0:0:0: [sdb] 7959552 512-byte logical blocks: (4.07 GB/3.79 GiB)
[ 3.524490] sd 2:0:0:0: [sdb] Write Protect is off
[ 3.530363] sd 2:0:0:0: [sdb] No Caching mode page found
[ 3.535734] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 3.549903] sdb: sdb1
[ 3.563202] sd 2:0:0:0: [sdb] Attached SCSI removable disk
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Checking root file system ... fsck from util-linux 2.25.2
rootfs: clean, 49661/248992 files, 443103/994560 blocks
done.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: udevd[ 15.384007] systemd-udevd[300]: starting version 215
. ok
[....] Synthesizing the initial hotplug events...[ 15.664791] input: gpio-keys as /devices/platform/gpio-keys/input/input0
done.
[....] Waiting for /dev to be fully populated...[ 15.823843] adt7475 0-002e: ADT7473 device, revision 2
[ 15.862602] adt7475 0-002e: Bypassing attenuators on: in1
[ 15.908578] orion_wdt: Initial timeout 21 sec
[ 15.948062] marvell-cesa: probe of f1030000.crypto failed with error -524
[ 16.037240] random: nonblocking pool is initialized
done.
[....] Checking root file system...fsck from util-linux 2.25.2
rootfs: clean, 49661/248992 files, 443103/994560 blocks
done.
[....] Activating lvm and md swap...[ 18.300066] Adding 524284k swap on /swapfile. Priority:-1 extents:225 across:752796k FS
done.
[....] Checking file systems...fsck from util-linux 2.25.2
done.
[ ok ] Loading kernel modules...done.
[ ok ] Cleaning up temporary files... /tmp.
[ 19.104501] EXT4-fs (sda1): mounted filesystem with writeback data mode. Opts: data=writeback
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables ...done.
[ 20.248944] NET: Registered protocol family 10
[ 20.357204] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1
Copyright 2004-2014 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/00:d0:b8:14:0b:8a
Sending on LPF/eth0/00:d0:b8:14:0b:8a
Sending on Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4
[ 24.022996] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 24.032919] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPOFFER from 192.168.2.1
DHCPACK from 192.168.2.1
Reloading /etc/samba/smb.conf: smbd.
bound to 192.168.2.101 -- renewal in 39399 seconds.
done.
[ ok ] Starting rpcbind daemon....
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1262 (syslogd)
. ok
[ ok ] Starting periodic command scheduler: cron.
[ ok ] Starting system message bus: dbus.
[ ok ] Starting the hd-idle daemon: hd-idle.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ ok ] Starting NFS common utilities: statd idmapd.
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1260 (klogd)
. ok
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting ftp server: proftpd.
[ ok ] Starting NetBIOS name server: nmbd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[ ok ] Starting SMB/CIFS daemon: smbd.
Debian GNU/Linux 8 IOMEGA-EZ ttyS0
IOMEGA-EZ login:
please ignore post above, here it is
|
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? June 04, 2017 01:22PM |
Admin Registered: 13 years ago Posts: 19,107 |
So now SPI is working and MTD is working. But the definition seems wrong.
You need to:
1. Look for the correct MTD definition (search here and NAS Central).
2. Look for the correct /etc/fw_env.config for this box.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
[ 1.593304] m25p80 spi0.0: mx25l8005 (1024 Kbytes) [ 1.598138] 3 cmdlinepart partitions found on MTD device spi0.0 [ 1.604118] Creating 3 MTD partitions on "spi0.0": [ 1.608932] 0x000000000000-0x00000007e000 : "u-boot" [ 1.613933] mtd: partition "u-boot" doesn't end on an erase block -- force read-only [ 1.622936] 0x00000007f000-0x000000080000 : "env" [ 1.627717] mtd: partition "env" doesn't start on an erase block boundary -- force read-only [ 1.637403] 0x00000007e000-0x00000007f000 : "env2" [ 1.642221] mtd: partition "env2" doesn't start on an erase block boundary -- force read-only
You need to:
1. Look for the correct MTD definition (search here and NAS Central).
2. Look for the correct /etc/fw_env.config for this box.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
iomega ez
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? June 05, 2017 08:52PM |
|
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? June 08, 2017 01:38AM |
Registered: 7 years ago Posts: 17 |
First, you are probably better off with a DTB that supports this device. There is no absolute guarantee that the DTB for the IX2-ng has all the bits and pieces in the correct place. That said, most of these devices are pretty close to being the same.
The MTD has sector misaligned problems even on the IX2-ng. This is because Linux does not know about the actual SPI flash chip in the device. Linux has picked the flash geometry for the closest SPI flash device that it knows about. The actual flash chip in the device can erase to page boundaries that the stock Linux driver just cannot use. Uboot knows about the page boundaries and sets up the Uboot environment to those boundaries but Linux chokes.
You would need to edit the Linux m25p80 flash driver to correct the problem.
The MTD has sector misaligned problems even on the IX2-ng. This is because Linux does not know about the actual SPI flash chip in the device. Linux has picked the flash geometry for the closest SPI flash device that it knows about. The actual flash chip in the device can erase to page boundaries that the stock Linux driver just cannot use. Uboot knows about the page boundaries and sets up the Uboot environment to those boundaries but Linux chokes.
You would need to edit the Linux m25p80 flash driver to correct the problem.
|
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? June 08, 2017 01:48AM |
Registered: 7 years ago Posts: 17 |
I need to point out that the MTD sector misaligned problem is documented in the kirkwood-lenovo-ix2-ng.dts file. If your device has the same SPI flash chip, you will have the same problem. If your device has a different SPI flash chip, you need a DTB/DTS file that supports the hardware in your device.
|
iomega ez
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? June 12, 2017 08:18PM |
|
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? June 13, 2017 08:38PM |
Admin Registered: 13 years ago Posts: 19,107 |
iomega ez Wrote:
-------------------------------------------------------
> as far as I know, they use the same board. but EZ
> boark have only 1 sata port and 128MB memory on bo
> ard.
>
> same board but less parts.
Since you have serial console, and can set the envs there, no need to worry about the MTD. As long as other aspects of this box are working then it is fine. You can remove the mtdparts from bootargs.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> as far as I know, they use the same board. but EZ
> boark have only 1 sata port and 128MB memory on bo
> ard.
>
> same board but less parts.
Since you have serial console, and can set the envs there, no need to worry about the MTD. As long as other aspects of this box are working then it is fine. You can remove the mtdparts from bootargs.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
iomega_ez
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? June 22, 2017 07:54PM |
from wiki page
wiki
but on dts file(kirkwood-lenovo-ix2-ng.dts)
is this why I have wrong MTD?
wiki
tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 1:0:0:0: [sda] Sector size 0 reported, assuming 512. SPI Serial flash detected @ 0xf4000000, 1024KB (256sec x 4KB) 3 cmdlinepart partitions found on MTD device spi_flash Creating 3 MTD partitions on "spi_flash": 0x000000000000-0x00000007e000 : "u-boot" 0x00000007f000-0x000000080000 : "env" 0x00000007e000-0x00000007f000 : "env2" sda:Using Hamming 1-bit ECC for NAND device No NAND device found!!!
but on dts file(kirkwood-lenovo-ix2-ng.dts)
#include "kirkwood-lenovo-ix2-common.dtsi"
/ {
model = "Lenovo IX2-ng";
compatible = "lenovo,ix2", "marvell,kirkwood-88f6282", "marvell,kirkwood";
ocp@f1000000 {
spi@10600 {
status = "okay";
flash@0 {
#address-cells = <1>;
#size-cells = <1>;
/* MX25L8006E can do 4K sector handling but
* sadly not in spi-nor.c yet.
*/
// compatible = "mxicy,mx25l8006e", "jedec,spi-nor";
compatible = "mxicy,mx25l8005", "jedec,spi-nor";
spi-max-frequency = <50000000>;
reg = <0>; /* Chip-select 0 */
mode = <0>;
partition@0 {
reg = <0x0 0x7e000>;
label = "u-boot";
};
partition@1 {
reg = <0x7e000 0x1000>;
label = "u-boot env2";
};
partition@2 {
reg = <0x7f000 0x1000>;
label = "u-boot env";
};
};
};
};
};
is this why I have wrong MTD?
|
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? June 22, 2017 11:18PM |
Admin Registered: 13 years ago Posts: 19,107 |
iomega_ez,
> is this why I have wrong MTD?
Not really. What you have
is the same as in the DTS.
Regardless, the mtdparts in bootargs takes precedent. So it is fine.
The error Indicated that the flash sector boundary is not 0x1000 (4K).
So the only explanation for this error is the flash sectore boundary is 0x10000 (64K). But your stock boot log says it is 4K.
So the DTS needs to be defined differently for this box to match the one that u-boot already knows about (4K).
.
Please post what you know about the SPI flash type (probably from GPL or webistes such as NASCentral), and also post the DTS that you are using.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 4 time(s). Last edit at 06/23/2017 01:10AM by bodhi.
> is this why I have wrong MTD?
Not really. What you have
mtdparts=spi0.0:0x7e000@0(u-boot),0x1000@0x7f000(env),0x1000@0x7e000(env2)
is the same as in the DTS.
> partition@0 {
> reg = <0x0 0x7e000>;
> label = "u-boot";
> };
>
> partition@1 {
> reg = <0x7e000 0x1000>;
> label = "u-boot env2";
> };
>
> partition@2 {
> reg = <0x7f000 0x1000>;
> label = "u-boot env";
Regardless, the mtdparts in bootargs takes precedent. So it is fine.
The error Indicated that the flash sector boundary is not 0x1000 (4K).
[ 1.593304] m25p80 spi0.0: mx25l8005 (1024 Kbytes) [ 1.598138] 3 cmdlinepart partitions found on MTD device spi0.0 [ 1.604118] Creating 3 MTD partitions on "spi0.0": [ 1.608932] 0x000000000000-0x00000007e000 : "u-boot" [ 1.613933] mtd: partition "u-boot" doesn't end on an erase block -- force read-only [ 1.622936] 0x00000007f000-0x000000080000 : "env" [ 1.627717] mtd: partition "env" doesn't start on an erase block boundary -- force read-only [ 1.637403] 0x00000007e000-0x00000007f000 : "env2" [ 1.642221] mtd: partition "env2" doesn't start on an erase block boundary -- force read-only
So the only explanation for this error is the flash sectore boundary is 0x10000 (64K). But your stock boot log says it is 4K.
SPI Serial flash detected @ 0xf4000000, 1024KB (256sec x 4KB)
So the DTS needs to be defined differently for this box to match the one that u-boot already knows about (4K).
.
Please post what you know about the SPI flash type (probably from GPL or webistes such as NASCentral), and also post the DTS that you are using.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 4 time(s). Last edit at 06/23/2017 01:10AM by bodhi.
|
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? June 27, 2017 12:03PM |
Registered: 7 years ago Posts: 17 |
Just changing the DTS won't help the fact that Linux does not know about that flash chip. It would require patching the SPI flash driver to recognize the chip correctly.
You can, however, get the U-Boot environment to appear correctly in Linux. It will be in read-only mode because Linux can't erase/program to the 4K sector boundaries of the U-Boot environment.
In Debian, you need to install "u-boot-tools" package. Then put this in a configuration file named "/etc/fw_env.config". You will have to be "root" to do these things.
# device Offset Size Sector size
/dev/mtd2 0x7e000 0x1000 0x1000
/dev/mtd1 0x7f000 0x1000 0x1000
This will describe where the U-Boot environment(s) are to the U-Boot tools. Now you should be able to use the "fw_printenv" command. You will have to be "root" or you will have to change the permissions on the "/dev/mtd" devices to use the fw_printenv command.
You can, however, get the U-Boot environment to appear correctly in Linux. It will be in read-only mode because Linux can't erase/program to the 4K sector boundaries of the U-Boot environment.
In Debian, you need to install "u-boot-tools" package. Then put this in a configuration file named "/etc/fw_env.config". You will have to be "root" to do these things.
# device Offset Size Sector size
/dev/mtd2 0x7e000 0x1000 0x1000
/dev/mtd1 0x7f000 0x1000 0x1000
This will describe where the U-Boot environment(s) are to the U-Boot tools. Now you should be able to use the "fw_printenv" command. You will have to be "root" or you will have to change the permissions on the "/dev/mtd" devices to use the fw_printenv command.
|
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? June 27, 2017 01:07PM |
Admin Registered: 13 years ago Posts: 19,107 |
sarcastic.mannequin,
> Just changing the DTS won't help the fact that Lin
> ux does not know about that flash chip. It would r
> equire patching the SPI flash driver to recognize
> the chip correctly.
True, there are 2 parts: DTS and dirver. If the flash type appear on the list, then it's easier. If it is not, then some change in the driver is needed, and it might be quite simple, might be not.
> In Debian, you need to install "u-boot-tools" pack
> age. Then put this in a configuration file named "
> /etc/fw_env.config". You will have to be "root" to
> do these things.
>
> # device Offset Size Sector size
> /dev/mtd2 0x7e000 0x1000 0x1000
> /dev/mtd1 0x7f000 0x1000 0x1000
>
> This will describe where the U-Boot environment(s)
> are to the U-Boot tools. Now you should be able to
> use the "fw_printenv" command. You will have to be
> "root" or you will have to change the permissions
> on the "/dev/mtd" devices to use the fw_printenv
> command.
All these are in the rootfs Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> Just changing the DTS won't help the fact that Lin
> ux does not know about that flash chip. It would r
> equire patching the SPI flash driver to recognize
> the chip correctly.
True, there are 2 parts: DTS and dirver. If the flash type appear on the list, then it's easier. If it is not, then some change in the driver is needed, and it might be quite simple, might be not.
> In Debian, you need to install "u-boot-tools" pack
> age. Then put this in a configuration file named "
> /etc/fw_env.config". You will have to be "root" to
> do these things.
>
> # device Offset Size Sector size
> /dev/mtd2 0x7e000 0x1000 0x1000
> /dev/mtd1 0x7f000 0x1000 0x1000
>
> This will describe where the U-Boot environment(s)
> are to the U-Boot tools. Now you should be able to
> use the "fw_printenv" command. You will have to be
> "root" or you will have to change the permissions
> on the "/dev/mtd" devices to use the fw_printenv
> command.
All these are in the rootfs Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
iomega ez
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? July 01, 2017 12:07AM |
|
iomega ez
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? July 01, 2017 02:23AM |
|
Re: Can install Bodhi's kernel on still 'unsupported' kirkwood device? July 01, 2017 02:59AM |
Admin Registered: 13 years ago Posts: 19,107 |
Take a look at the benchmarks to see how other people are testing it:
http://forum.doozan.com/read.php?2,23630
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
http://forum.doozan.com/read.php?2,23630
Quote
Benchmarks
Pogo ProV3 vs Pogo E02
Another Pogo Pro V3 benchmarks
Network performance - SAMBA - NFS (various protocols)
Pogo Pro V3 Network NFS benchmarks
Kirkwood vs OXNAS network performance (with flow control)
Kirkwood vs OXNAS network performance (flow control turned off )
OXNAS vs OXNAS network performance (flow control turned off)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on Iomega EZ Media & Backup Center August 17, 2017 04:01PM |
Admin Registered: 13 years ago Posts: 19,107 |
Here is the kirkwood-lenovo-iomega-ez.dtb for testing.
Please try and let me know.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Please try and let me know.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on Iomega EZ Media & Backup Center November 27, 2017 07:26PM |
Registered: 7 years ago Posts: 2 |
Hi I am trying to install Debian on a Iomega’s Ez Media & Backup Center
I have a 6Tb empty Hardrive ready to make some test,
I have serial-ttl cable, and pin of ttl identified on the board.
I have a ready to use debian VM and connected a USB to Sata Cable that I was able to use with another 6Tb HardDrive to flash a WDMyBookLive-Single with LEDE and It worked perfectly.
I have asked for help in LEDE forums and one user prepared to me a file with LEDE but it is not uImage formatted: https://forum.lede-project.org/t/lenovo-iomega-ez-media-backup-center/5031
I want to try to install LEDE or Debian.
Thanks.
I have a 6Tb empty Hardrive ready to make some test,
I have serial-ttl cable, and pin of ttl identified on the board.
I have a ready to use debian VM and connected a USB to Sata Cable that I was able to use with another 6Tb HardDrive to flash a WDMyBookLive-Single with LEDE and It worked perfectly.
I have asked for help in LEDE forums and one user prepared to me a file with LEDE but it is not uImage formatted: https://forum.lede-project.org/t/lenovo-iomega-ez-media-backup-center/5031
I want to try to install LEDE or Debian.
Thanks.
|
Re: Debian on Iomega EZ Media & Backup Center November 27, 2017 09:54PM |
Admin Registered: 13 years ago Posts: 19,107 |
braian87b,
Create the USB rootfs using Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2 (24 Jul 2017).
https://forum.doozan.com/read.php?2,12096
And use the kirkwood-lenovo-iomega-ez.dtb from this post:
https://forum.doozan.com/read.php?2,15887,36138#msg-36138
If you have serial console, then try what iomega_ez did to set up booting the new USB rootfs:
https://forum.doozan.com/read.php?2,15887,34541#msg-34541
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Create the USB rootfs using Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2 (24 Jul 2017).
https://forum.doozan.com/read.php?2,12096
And use the kirkwood-lenovo-iomega-ez.dtb from this post:
https://forum.doozan.com/read.php?2,15887,36138#msg-36138
If you have serial console, then try what iomega_ez did to set up booting the new USB rootfs:
https://forum.doozan.com/read.php?2,15887,34541#msg-34541
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on Iomega EZ Media & Backup Center February 12, 2019 12:38PM |
Registered: 5 years ago Posts: 6 |
The Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2 with the kirkwood-lenovo-iomega-ez.dtb still shows
I found that
while stock firmware has 0x00001000 erasesize.
How can I correct this?
Edited 3 time(s). Last edit at 02/12/2019 01:22PM by jeon.
[ 7.781037] mtd: partition "u-boot" doesn't end on an erase/write block -- force read-only [ 7.796000] mtd: partition "u-boot env2" doesn't start on an erase/write block boundary -- force read-only [ 7.812164] mtd: partition "u-boot env" doesn't start on an erase/write block boundary -- force read-only
I found that
$ cat /proc/mtd
dev: size erasesize name
mtd0: 0007e000 00010000 "u-boot"
mtd1: 00001000 00010000 "u-boot env2"
mtd2: 00001000 00010000 "u-boot env"
while stock firmware has 0x00001000 erasesize.
$ cat /proc/mtd dev: size erasesize name mtd0: 0007e000 00001000 "u-boot" mtd1: 00001000 00001000 "env" mtd2: 00001000 00001000 "env2"
How can I correct this?
Edited 3 time(s). Last edit at 02/12/2019 01:22PM by jeon.
|
Re: Debian on Iomega EZ Media & Backup Center February 12, 2019 02:02PM |
Admin Registered: 13 years ago Posts: 19,107 |
jeon,
With Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2 rootfs, get these info:
If you have stock u-boot envs and bootlog, please post here also.
It seems there is a mismatch somewhere in your u-boot envs, and how the kernel detect the SPI chip.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 02/12/2019 02:04PM by bodhi.
With Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2 rootfs, get these info:
dmesg fw_printenv cat /proc/mtd
If you have stock u-boot envs and bootlog, please post here also.
It seems there is a mismatch somewhere in your u-boot envs, and how the kernel detect the SPI chip.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 02/12/2019 02:04PM by bodhi.
