Cannot boot any image anymore pogoplug V4 July 08, 2015 05:06PM |
Registered: 11 years ago Posts: 25 |
Pogov4> printenv p r i n t e n v arcNumber=3960 baudrate=115200 bootcmd=run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; reset bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot; bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot; bootdelay=10 console=ttyS0,115200 device=0:1 ethact=egiga0 ethaddr=00:25:re:da:ct:ed if_netconsole=ping $serverip ipaddr=192.168.1.128 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=ext2load usb 0:1 0x1c00000 /boot/dts/kirkwood-pogoplug_v4.dtb load_initrd=ext2load usb 0:1 0x1100000 /boot/uInitrd load_uimage=ext2load usb 0:1 0x800000 /boot/uImage machid=f78 mainlineLinux=yes mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi mmc_init=mmc rescan mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd mmc_root=/dev/mmcblk0p1 mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) ncip=192.168.1.252 partition=nand0,2 preboot=run preboot_nc preboot_nc=run if_netconsole start_netconsole rootdelay=10 rootfstype=ext2 sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi sata_init=ide reset sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd sata_root=/dev/sda1 serverip=192.168.1.252 set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=nc stdin=nc stdout=nc usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_init=usb start; setenv usb_root LABEL=rootfs usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd usb_root=/dev/sda1 Environment size: 2480/131068 byteshere is an example of boot
Pogov4> run usb_boot r u n u s b _ b o o t 2756040 bytes read in 401 ms (6.6 MiB/s) 6032465 bytes read in 520 ms (11.1 MiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.16.0-kirkwood-tld-2 Created: 2014-09-01 23:18:31 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2755976 Bytes = 2.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-3.16.0-kirkwood-tld-2 Created: 2014-09-01 23:18:48 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6032401 Bytes = 5.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ...
Re: Cannot boot any image anymore pogoplug V4 July 08, 2015 05:35PM |
Admin Registered: 13 years ago Posts: 18,594 |
rootfstype=ext2
setenv rootfstype ext3After booted into Debian, set it permanently
fw_setenv rootfstype ext3
Re: Cannot boot any image anymore pogoplug V4 July 08, 2015 06:53PM |
Registered: 11 years ago Posts: 25 |