Debian on iomega storcenter ix4-200d: succes! July 12, 2015 01:30PM |
Registered: 9 years ago Posts: 7 |
/dts-v1/; #include "kirkwood.dtsi" #include "kirkwood-6281.dtsi" / { model = "Iomega ix4-2OOd"; compatible = "marvell,rd88f6281-a", "marvell,rd88f6281","marvell,kirkwood-88f6281", "marvell,kirkwood"; memory { device_type = "memory"; reg = <0x00000000 0x20000000>; }; chosen { bootargs = "console=ttyS0,115200n8 earlyprintk"; stdout-path = &uart0; }; mbus { pcie-controller { status = "okay"; pcie@1,0 { status = "okay"; }; }; }; ocp@f1000000 { serial@12000 { status = "ok"; }; sata@80000 { status = "okay"; nr-ports = <2>; }; }; }; &nand { status = "okay"; partition@0 { label = "u-boot"; reg = <0x0000000 0x100000>; read-only; }; partition@100000 { label = "uImage"; reg = <0x0100000 0x200000>; }; partition@300000 { label = "rootfs"; reg = <0x0300000 0x500000>; }; }; &mdio { status = "okay"; ethphy0: ethernet-phy@8 { device_type = "ethernet-phy"; reg = <8>; }; ethphy1: ethernet-phy@9 { device_type = "ethernet-phy"; reg = <9>; }; }; ð0 { status = "okay"; ethernet0-port@0 { phy-handle = <ðphy0>; }; }; ð1 { status = "okay"; ethernet1-port@0 { phy-handle = <ðphy1>; }; };
CN4 -------------- | 9 8 6 4 2 | | 10 7 5 3 1 | -------------- PIN 1 Mark (fat line) 1 = RXD 4 = TXD 6 = GND 10 = 3.3v
Re: Debian on iomega storcenter ix4-200d: succes! July 12, 2015 01:41PM |
Admin Registered: 14 years ago Posts: 19,302 |
Re: Debian on iomega storcenter ix4-200d: succes! July 12, 2015 02:25PM |
Registered: 9 years ago Posts: 7 |
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** uboot_ver:v1.1.0 ** ** MARVELL BOARD: IX4-110 LE U-Boot 1.1.4 (Oct 15 2009 - 17:28:22) Marvell version: 3.4.18 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CF600 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM CS[1] base 0x10000000 size 256MB DRAM Total size 512MB 16bit width Found 0x20 i2c device Set Power State as Always On Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:32 MB Found ADT7473, program LED ...(led_volt=90) OK Found ADT7473, program thermal/Fan ...(pwm_min=0) (pwm_max=130) (therm=67) (temp_min=60) OK Marvell Serial ATA Adapter Integrated Sata device found CPU : Marvell Feroceon (Rev 1) Found initrd at 0x2d4000 Streaming disabled Write allocate disabled Module 0 is RGMII Module 1 is RGMII USB 0: host mode PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 SCSI: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x7 impl IDE mode flags: 64bit ncq stag led pmp slum part scanning bus for devices... Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 (Re)start USB... USB: scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found .... ................................................................................................................................................................................................................................................................................... 2874910 bytes read .... . ...... ............ ......................... ................................................... ...................................................................................................... ............................................................................................................................................................................................................ .... ............................................................................................................................................................................................................................... 6535284 bytes read ## Booting image at 00800000 ... Image Name: Linux-3.18.5-kirkwood-tld-1 Created: 2000-01-14 21:59:00 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2874846 Bytes = 2.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 01100000 ... Image Name: initramfs-3.18.5-kirkwood-tld-1 Created: 2015-02-19 1:49:36 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6535220 Bytes = 6.2 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.18.5-kirkwood-tld-1 (root@tldDebian) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 PREEMPT Thu Feb 5 17:58:07 PST 2015 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine model: Iomega ix4-2OOd [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 rootfstype=ext2 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 504792K/524288K available (5640K kernel code, 365K rwdata, 1920K rodata, 268K init, 305K bss, 19496K reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc076a240 (7561 kB) [ 0.000000] .init : 0xc076b000 - 0xc07ae000 ( 268 kB) [ 0.000000] .data : 0xc07ae000 - 0xc08096fc ( 366 kB) [ 0.000000] .bss : 0xc08096fc - 0xc0855d84 ( 306 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000014] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474836475ns [ 0.000373] Console: colour dummy device 80x30 [ 0.000400] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584) [ 0.090111] pid_max: default: 32768 minimum: 301 [ 0.090250] Security Framework initialized [ 0.090345] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090364] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.091046] Initializing cgroup subsys devices [ 0.091077] Initializing cgroup subsys freezer [ 0.091107] Initializing cgroup subsys net_cls [ 0.091127] Initializing cgroup subsys blkio [ 0.091221] CPU: Testing write buffer coherency: ok [ 0.091609] Setting up static identity map for 0x557418 - 0x557470 [ 0.091873] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.094041] devtmpfs: initialized [ 0.096475] prandom: seed boundary self test passed [ 0.100561] prandom: 100 self tests passed [ 0.100588] pinctrl core: initialized pinctrl subsystem [ 0.101037] regulator-dummy: no parameters [ 0.104557] NET: Registered protocol family 16 [ 0.104951] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.130104] cpuidle: using governor ladder [ 0.160102] cpuidle: using governor menu [ 0.160470] Feroceon L2: Enabling L2 [ 0.160513] Feroceon L2: Cache support initialised. [ 0.160858] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.160951] [Firmware Info]: /ocp@f1000000/ethernet-controller@76000/ethernet1-port@0: local-mac-address is not set [ 0.165051] No ATAGs? [ 0.201720] vgaarb: loaded [ 0.202085] usbcore: registered new interface driver usbfs [ 0.202168] usbcore: registered new interface driver hub [ 0.202231] usbcore: registered new device driver usb [ 0.203247] Switched to clocksource orion_clocksource [ 0.240850] NET: Registered protocol family 2 [ 0.241579] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.241636] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.241689] TCP: Hash tables configured (established 4096 bind 4096) [ 0.241748] TCP: reno registered [ 0.241762] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.241784] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.241979] NET: Registered protocol family 1 [ 0.242320] RPC: Registered named UNIX socket transport module. [ 0.242333] RPC: Registered udp transport module. [ 0.242340] RPC: Registered tcp transport module. [ 0.242347] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.242606] Unpacking initramfs... [ 0.784251] Freeing initrd memory: 6384K (c1100000 - c173c000) [ 0.784366] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.785661] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.785693] Initialise system trusted keyring [ 0.785787] audit: initializing netlink subsys (disabled) [ 0.785842] audit: type=2000 audit(0.780:1): initialized [ 0.786594] zpool: loaded [ 0.786612] zbud: loaded [ 0.786907] VFS: Disk quotas dquot_6.5.2 [ 0.786966] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.787544] NFS: Registering the id_resolver key type [ 0.787594] Key type id_resolver registered [ 0.787603] Key type id_legacy registered [ 0.787629] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.787643] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.787860] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.788182] msgmni has been set to 998 [ 0.788339] Key type big_key registered [ 0.791112] alg: No test for stdrng (krng) [ 0.791155] Key type asymmetric registered [ 0.791171] Asymmetric key parser 'x509' registered [ 0.791262] bounce: pool size: 64 pages [ 0.791346] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.791369] io scheduler noop registered [ 0.791385] io scheduler deadline registered [ 0.791440] io scheduler cfq registered (default) [ 0.792729] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 0.793462] irq: Cannot allocate irq_descs @ IRQ33, assuming pre-allocated [ 0.793867] irq: Cannot allocate irq_descs @ IRQ65, assuming pre-allocated [ 0.794675] mvebu-pcie mbus:pcie-controller: PCI host bridge to bus 0000:00 [ 0.794695] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 0.794709] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 0.794723] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.795022] PCI: bus0: Fast back to back transfers disabled [ 0.795038] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.795727] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 0.795762] PCI: bus1: Fast back to back transfers disabled [ 0.795855] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 0.795872] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff] [ 0.795891] pci 0000:01:00.0: BAR 5: assigned [mem 0xe0000000-0xe00003ff] [ 0.795910] pci 0000:01:00.0: BAR 4: assigned [io 0x10000-0x1000f] [ 0.795927] pci 0000:01:00.0: BAR 0: assigned [io 0x10010-0x10017] [ 0.795945] pci 0000:01:00.0: BAR 2: assigned [io 0x10018-0x1001f] [ 0.795962] pci 0000:01:00.0: BAR 1: assigned [io 0x10020-0x10023] [ 0.795979] pci 0000:01:00.0: BAR 3: assigned [io 0x10024-0x10027] [ 0.795995] pci 0000:00:01.0: PCI bridge to [bus 01] [ 0.796007] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 0.796022] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 0.796307] mv_xor f1060800.xor: Marvell shared XOR driver [ 0.833334] mv_xor f1060800.xor: Marvell XOR: ( xor cpy ) [ 0.873307] mv_xor f1060800.xor: Marvell XOR: ( xor cpy ) [ 0.873497] mv_xor f1060900.xor: Marvell shared XOR driver [ 0.913306] mv_xor f1060900.xor: Marvell XOR: ( xor cpy ) [ 0.953305] mv_xor f1060900.xor: Marvell XOR: ( xor cpy ) [ 0.953717] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.955057] console [ttyS0] disabled [ 0.955115] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 1.686995] console [ttyS0] enabled [ 1.691829] nand: device found, Manufacturer ID: 0xec, Chip ID: 0x75 [ 1.698248] nand: Samsung NAND 32MiB 3,3V 8-bit [ 1.702803] nand: 32MiB, SLC, page size: 512, OOB size: 16 [ 1.708343] Scanning device for bad blocks [ 1.935726] libphy: Fixed MDIO Bus: probed [ 1.940155] libphy: orion_mdio_bus: probed [ 1.953180] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 3.033921] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:26:2d:06:77:48 [ 4.114027] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:26:2d:06:77:49 [ 4.122994] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.129590] ehci-pci: EHCI PCI platform driver [ 4.134143] ehci-orion: EHCI orion driver [ 4.138331] orion-ehci f1050000.ehci: EHCI Host Controller [ 4.143896] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 4.151837] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 4.173283] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 4.179509] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.186356] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.193630] usb usb1: Product: EHCI Host Controller [ 4.198530] usb usb1: Manufacturer: Linux 3.18.5-kirkwood-tld-1 ehci_hcd [ 4.205279] usb usb1: SerialNumber: f1050000.ehci [ 4.210722] hub 1-0:1.0: USB hub found [ 4.214578] hub 1-0:1.0: 1 port detected [ 4.219383] mousedev: PS/2 mouse device common for all mice [ 4.225633] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 4.232703] i2c /dev entries driver [ 4.237128] hidraw: raw HID events driver (C) Jiri Kosina [ 4.242900] drop_monitor: Initializing network drop monitor service [ 4.249471] TCP: cubic registered [ 4.252809] NET: Registered protocol family 17 [ 4.257425] Key type dns_resolver registered [ 4.262505] Loading compiled-in X.509 certificates [ 4.267383] registered taskstats version 1 [ 4.272518] rtc-mv f1010300.rtc: setting system clock to 2000-01-14 21:59:51 UTC (947887191) [ 4.283188] Freeing unused kernel memory: 268K (c076b000 - c07ae000) Loading, please wait... [ 4.354611] systemd-udevd[61]: starting version 215 [ 4.361558] random: systemd-udevd urandom read with 7 bits of entropy available [ 4.510677] SCSI subsystem initialized [ 4.533428] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 4.561892] pci 0000:00:01.0: enabling device (0140 -> 0143) [ 4.569946] sata_mv f1080000.sata: slots 32 ports 2 [ 4.599331] ahci 0000:01:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this. [ 4.621233] scsi host0: sata_mv [ 4.639576] scsi host1: sata_mv [ 4.643080] ata1: SATA max UDMA/133 irq 32 [ 4.657543] ahci 0000:01:00.0: controller can't do NCQ, turning off CAP_NCQ [ 4.672142] ata2: SATA max UDMA/133 irq 32 [ 4.691921] ahci 0000:01:00.0: controller can't do PMP, turning off CAP_PMP [ 4.700732] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 4.712528] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 4.727751] usb 1-1: Product: USB2.0 Hub [ 4.736463] hub 1-1:1.0: USB hub found [ 4.743318] hub 1-1:1.0: 4 ports detected [ 4.748314] ahci 0000:01:00.0: masking port_map 0x7 -> 0x3 [ 4.774944] ahci 0000:01:00.0: SSS flag set, parallel bus scan disabled [ 4.781658] ahci 0000:01:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode [ 4.799368] ahci 0000:01:00.0: flags: 64bit stag led slum part [ 4.809722] scsi host2: ahci [ 4.813613] scsi host3: ahci [ 4.817427] scsi host4: ahci [ 4.821071] ata3: SATA max UDMA/133 abar m1024@0xe0000000 port 0xe0000100 irq 83 [ 4.828618] ata4: SATA max UDMA/133 abar m1024@0xe0000000 port 0xe0000180 irq 83 [ 4.836088] ata5: DUMMY [ 5.033597] usb 1-1.2: new high-speed USB device number 3 using orion-ehci [ 5.043288] ata1: SATA link down (SStatus 0 SControl F300) [ 5.144221] usb 1-1.2: New USB device found, idVendor=0781, idProduct=5406 [ 5.151143] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 5.158526] usb 1-1.2: Product: U3 Cruzer Micro [ 5.163075] usb 1-1.2: Manufacturer: SanDisk [ 5.167404] usb 1-1.2: SerialNumber: 0775120CC542857C [ 5.181799] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 5.188212] ata3: SATA link down (SStatus 0 SControl 300) [ 5.194065] scsi host5: usb-storage 1-1.2:1.0 [ 5.200176] usbcore: registered new interface driver usb-storage [ 5.209160] usbcore: registered new interface driver uas [ 5.413292] ata2: SATA link down (SStatus 0 SControl F300) [ 5.783294] ata4: SATA link down (SStatus 0 SControl 300) [ 6.194193] scsi 5:0:0:0: Direct-Access SanDisk Cruzer 7.01 PQ: 0 ANSI: 0 CCS [ 6.203313] scsi 5:0:0:1: CD-ROM SanDisk Cruzer 7.01 PQ: 0 ANSI: 0 [ 6.218024] sd 5:0:0:0: [sda] 3907583 512-byte logical blocks: (2.00 GB/1.86 GiB) [ 6.231776] sd 5:0:0:0: [sda] Write Protect is off [ 6.239395] sd 5:0:0:0: [sda] No Caching mode page found [ 6.244930] sd 5:0:0:0: [sda] Assuming drive cache: write through [ 6.252812] sr 5:0:0:1: [sr0] scsi3-mmc drive: 48x/48x tray [ 6.258719] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 6.270239] sda: sda1 [ 6.275768] sd 5:0:0:0: [sda] Attached SCSI removable disk [ 6.285074] sd 5:0:0:0: Attached scsi generic sg0 type 0 [ 6.291247] sr 5:0:0:1: Attached scsi generic sg1 type 5 [ 6.434159] sr 5:0:0:1: [sr0] GET_EVENT and TUR disagree continuously, suppress GET_EVENT events Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Running /scripts/local-bottom ... done. done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 17.044175] systemd-udevd[273]: starting version 215 . ok [ ok ] Synthesizing the initial hotplug events...done. [....] Waiting for /dev to be fully populated...[ 17.502011] orion_wdt: Initial timeout 21 sec [ 17.777344] random: nonblocking pool is initialized [ 17.814250] sr 5:0:0:1: [sr0] [ 17.817410] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE [ 17.823307] sr 5:0:0:1: [sr0] [ 17.826460] Sense Key : Hardware Error [current] [ 17.831216] sr 5:0:0:1: [sr0] [ 17.834388] Add. Sense: No additional sense information [ 17.839665] sr 5:0:0:1: [sr0] CDB: [ 17.843166] Read(10): 28 00 00 00 7f fc 00 00 02 00 [ 17.848202] blk_update_request: I/O error, dev sr0, sector 131056 [ 17.915367] sr 5:0:0:1: [sr0] [ 17.918546] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE [ 17.924431] sr 5:0:0:1: [sr0] [ 17.927605] Sense Key : Hardware Error [current] [ 17.932349] sr 5:0:0:1: [sr0] [ 17.935537] Add. Sense: No additional sense information [ 17.940791] sr 5:0:0:1: [sr0] CDB: [ 17.944323] Read(10): 28 00 00 00 7f fc 00 00 01 00 [ 17.949328] blk_update_request: I/O error, dev sr0, sector 131056 [ 17.955470] Buffer I/O error on dev sr0, logical block 32764, async page read [ 18.024491] sr 5:0:0:1: [sr0] [ 18.027666] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE [ 18.033553] sr 5:0:0:1: [sr0] [ 18.036727] Sense Key : Hardware Error [current] [ 18.041472] sr 5:0:0:1: [sr0] [ 18.044657] Add. Sense: No additional sense information [ 18.049913] sr 5:0:0:1: [sr0] CDB: [ 18.053443] Read(10): 28 00 00 00 7f fd 00 00 01 00 [ 18.058450] blk_update_request: I/O error, dev sr0, sector 131060 [ 18.064592] Buffer I/O error on dev sr0, logical block 32765, async page read done. [ ok ] Activating swap...done. [....] Checking root file system...fsck from util-linux 2.25.2 rootfs: clean, 14354/122160 files, 115705/488191 blocks done. [ ok ] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.25.2 done. [ ok ] Loading kernel modules...done. [ ok ] Cleaning up temporary files... /tmp. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables ...done. [ 21.646146] NET: Registered protocol family 10 [ 23.637580] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 23.648723] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ ok ] Configuring network interfaces...done. [ ok ] Starting rpcbind daemon.... [ 25.622237] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 25.632185] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1263 (syslogd) . ok [ ok ] Starting system message bus: dbus. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1261 (klogd) . ok Debian GNU/Linux 8 debian ttyS0
Re: Debian on iomega storcenter ix4-200d: succes! July 12, 2015 05:32PM |
Admin Registered: 14 years ago Posts: 19,302 |
Quote
Lenovo wants a cheque or money order to cover expenses before they will mail it to you on a cd. (https://lenovo-na-en.custhelp.com/app/answers/detail/a_id/34787)
Re: Debian on iomega storcenter ix4-200d: succes! July 14, 2015 04:47PM |
Registered: 9 years ago Posts: 7 |
adt7473-i2c-0-2e Adapter: mv64xxx_i2c adapter in1: +1.10 V (min = +0.00 V, max = +2.99 V) +3.3V: +3.33 V (min = +2.96 V, max = +3.61 V) fan1: 755 RPM (min = 0 RPM) fan2: 0 RPM (min = 0 RPM) fan3: 0 RPM (min = 0 RPM) fan4: 0 RPM (min = 0 RPM) temp1: +37.5 C (low = -63.0 C, high = +191.0 C) (crit = +100.0 C, hyst = +96.0 C) Board Temp: +43.5 C (low = -63.0 C, high = +191.0 C) (crit = +67.0 C, hyst = +65.0 C) temp3: +37.0 C (low = -63.0 C, high = +191.0 C) (crit = +67.0 C, hyst = +65.0 C)
Re: Debian on iomega storcenter ix4-200d: succes! July 14, 2015 06:31PM |
Admin Registered: 14 years ago Posts: 19,302 |
Re: Debian on iomega storcenter ix4-200d: succes! July 23, 2015 06:19PM |
Registered: 9 years ago Posts: 295 |
Bruno
Re: Debian on iomega storcenter ix4-200d: succes! November 04, 2015 10:27AM |
Re: Debian on iomega storcenter ix4-200d: succes! November 04, 2015 04:55PM |
Admin Registered: 14 years ago Posts: 19,302 |
Bruno
Re: Debian on iomega storcenter ix4-200d: succes! November 10, 2015 11:29AM |
Re: Debian on iomega storcenter ix4-200d: succes! January 29, 2016 10:25AM |
Admin Registered: 14 years ago Posts: 19,302 |
mtdinfo -a
apt-get install mtd-utils
Re: Debian on iomega storcenter ix4-200d: succes! January 30, 2016 05:34PM |
Registered: 9 years ago Posts: 7 |
Count of MTD devices: 3 Present MTD devices: mtd0, mtd1, mtd2 Sysfs interface supported: yes mtd0 Name: u-boot Type: nand Eraseblock size: 16384 bytes, 16.0 KiB Amount of eraseblocks: 40 (655360 bytes, 640.0 KiB) Minimum input/output unit size: 512 bytes Sub-page size: 256 bytes OOB size: 16 bytes Character device major/minor: 90:0 Bad blocks are allowed: true Device is writable: true mtd1 Name: env Type: nand Eraseblock size: 16384 bytes, 16.0 KiB Amount of eraseblocks: 4 (65536 bytes, 64.0 KiB) Minimum input/output unit size: 512 bytes Sub-page size: 256 bytes OOB size: 16 bytes Character device major/minor: 90:2 Bad blocks are allowed: true Device is writable: true mtd2 Name: flash Type: nand Eraseblock size: 16384 bytes, 16.0 KiB Amount of eraseblocks: 2048 (33554432 bytes, 32.0 MiB) Minimum input/output unit size: 512 bytes Sub-page size: 256 bytes OOB size: 16 bytes Character device major/minor: 90:4 Bad blocks are allowed: true Device is writable: true
Re: Debian on iomega storcenter ix4-200d: succes! January 30, 2016 05:40PM |
Admin Registered: 14 years ago Posts: 19,302 |
Re: Debian on iomega storcenter ix4-200d: succes! February 02, 2016 01:04PM |
Admin Registered: 14 years ago Posts: 19,302 |
nanddump --omitoob --noecc --file=ix4-200d-mtd0.kwb /dev/mtd0
Re: Debian on iomega storcenter ix4-200d: succes! February 04, 2016 03:20PM |
Registered: 9 years ago Posts: 7 |
Re: Debian on iomega storcenter ix4-200d: succes! February 04, 2016 03:34PM |
Admin Registered: 14 years ago Posts: 19,302 |
Re: Debian on iomega storcenter ix4-200d: succes! February 05, 2016 04:52AM |
Admin Registered: 14 years ago Posts: 19,302 |
find / -name '*blparam*'
Re: Debian on iomega storcenter ix4-200d: succes! February 09, 2016 04:49PM |
Registered: 9 years ago Posts: 7 |
Re: Debian on iomega storcenter ix4-200d: succes! February 09, 2016 05:13PM |
Admin Registered: 14 years ago Posts: 19,302 |
Re: Debian on iomega storcenter ix4-200d: succes! February 28, 2016 04:03PM |
Registered: 13 years ago Posts: 62 |
[ 11.160528] blk_update_request: I/O error, dev mtdblock4, sector 0 [ 11.167449] blk_update_request: I/O error, dev mtdblock4, sector 0 [ 11.173938] __nand_correct_data: uncorrectable ECC error [ 11.179335] blk_update_request: I/O error, dev mtdblock4, sector 0 [ 11.185868] __nand_correct_data: uncorrectable ECC error [ 11.191280] blk_update_request: I/O error, dev mtdblock3, sector 6016 [ 11.198004] __nand_correct_data: uncorrectable ECC error [ 11.203447] blk_update_request: I/O error, dev mtdblock3, sector 6128 [ 11.210201] __nand_correct_data: uncorrectable ECC error [ 11.215595] __nand_correct_data: uncorrectable ECC error [ 11.220993] blk_update_request: I/O error, dev mtdblock3, sector 6142 [ 11.227700] __nand_correct_data: uncorrectable ECC error [ 11.233137] blk_update_request: I/O error, dev mtdblock3, sector 0 [ 11.239528] __nand_correct_data: uncorrectable ECC error [ 11.244949] blk_update_request: I/O error, dev mtdblock3, sector 0 [ 11.253493] __nand_correct_data: uncorrectable ECC error [ 11.258886] blk_update_request: I/O error, dev mtdblock2, sector 0 [ 11.265629] __nand_correct_data: uncorrectable ECC error [ 11.271030] blk_update_request: I/O error, dev mtdblock2, sector 0 [ 11.277470] __nand_correct_data: uncorrectable ECC error [ 11.283179] __nand_correct_data: uncorrectable ECC error [ 11.288524] __nand_correct_data: uncorrectable ECC error [ 11.295145] __nand_correct_data: uncorrectable ECC error [ 11.301024] __nand_correct_data: uncorrectable ECC error [ 11.306645] __nand_correct_data: uncorrectable ECC error [ 11.311997] __nand_correct_data: uncorrectable ECC error [ 11.317697] __nand_correct_data: uncorrectable ECC error [ 11.323047] __nand_correct_data: uncorrectable ECC error [ 11.328686] __nand_correct_data: uncorrectable ECC error [ 11.334084] __nand_correct_data: uncorrectable ECC error [ 11.339741] __nand_correct_data: uncorrectable ECC error [ 11.345143] __nand_correct_data: uncorrectable ECC error [ 11.350710] __nand_correct_data: uncorrectable ECC errorand
[67754.085919] blk_update_request: I/O error, dev mtdblock2, sector 0 [67754.092478] blk_update_request: I/O error, dev mtdblock2, sector 0 [67754.098687] Buffer I/O error on dev mtdblock2, logical block 0, async page read [67754.108480] __nand_correct_data: uncorrectable ECC error [67754.113907] __nand_correct_data: uncorrectable ECC error [67754.119314] blk_update_request: I/O error, dev mtdblock3, sector 6016 [67754.127619] __nand_correct_data: uncorrectable ECC error [67754.133030] blk_update_request: I/O error, dev mtdblock3, sector 6016 [67754.139506] Buffer I/O error on dev mtdblock3, logical block 752, async page read [67754.151527] blk_update_request: I/O error, dev mtdblock4, sector 0 [67754.158719] blk_update_request: I/O error, dev mtdblock4, sector 0 [67754.164935] Buffer I/O error on dev mtdblock4, logical block 0, async page read [67754.302477] __nand_correct_data: uncorrectable ECC error [67754.307914] __nand_correct_data: uncorrectable ECC error [67754.314805] __nand_correct_data: uncorrectable ECC error [67754.320196] Buffer I/O error on dev mtdblock0, logical block 1, async page read [67754.332832] __nand_correct_data: uncorrectable ECC error [67754.338515] __nand_correct_data: uncorrectable ECC error [67754.345766] Buffer I/O error on dev mtdblock1, logical block 0, async page read [67754.357383] __nand_correct_data: uncorrectable ECC error [67754.362909] __nand_correct_data: uncorrectable ECC error [67754.369521] __nand_correct_data: uncorrectable ECC error [67754.375684] Buffer I/O error on dev mtdblock2, logical block 0, async page read [67754.384674] __nand_correct_data: uncorrectable ECC error [67754.390221] __nand_correct_data: uncorrectable ECC error [67754.396888] Buffer I/O error on dev mtdblock3, logical block 752, async page read [67754.407953] __nand_correct_data: uncorrectable ECC error [67754.414331] Buffer I/O error on dev mtdblock4, logical block 0, async page read [67754.568512] __nand_correct_data: uncorrectable ECC error [67754.574008] __nand_correct_data: uncorrectable ECC error
[ 34.122103] sd 4:0:0:0: [sde] 4096-byte physical blocks [ 34.130136] sd 4:0:0:0: [sde] Write Protect is off [ 34.136034] sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00 [ 34.136191] sd 4:0:0:0: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 34.719673] sde: sde1 sde2 [ 34.725286] sd 4:0:0:0: [sde] Attached SCSI removable disk [ 51.093138] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 51.100266] ata4.00: failed command: IDENTIFY DEVICE [ 51.106588] ata4.00: cmd ec/00:01:00:00:00/00:00:00:00:00/40 tag 12 pio 512 in [ 51.106588] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 51.121753] ata4.00: status: { DRDY } [ 51.125873] ata4: hard resetting link [ 51.473116] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 51.480360] ata4.00: configured for UDMA/133 [ 51.493612] ata4: EH complete [ 91.079424] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 91.086549] ata3.00: failed command: IDENTIFY DEVICE [ 91.093423] ata3.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 7 pio 512 in [ 91.093423] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 91.108941] ata3.00: status: { DRDY } [ 91.113428] ata3: hard resetting link [ 91.459213] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 91.466590] ata3.00: configured for UDMA/133 [ 91.474828] ata3: EH complete [ 112.068962] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 112.076369] ata4.00: failed command: IDENTIFY DEVICE [ 112.083378] ata4.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 19 pio 512 in [ 112.083378] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 112.099080] ata4.00: status: { DRDY } [ 112.102810] ata4: hard resetting link [ 112.448732] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 112.455994] ata4.00: configured for UDMA/133 [ 112.464328] ata4: EH complete [ 209.412877] ata1: sata_mv: attempting PIO w/multiple DRQ: this may fail due to h/w errata [ 210.312406] ata2: sata_mv: attempting PIO w/multiple DRQ: this may fail due to h/w errata [ 231.015605] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 231.022731] ata3.00: failed command: IDENTIFY DEVICE [ 231.029050] ata3.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 26 pio 512 in [ 231.029050] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 231.044611] ata3.00: status: { DRDY } [ 231.049048] ata3: hard resetting link [ 231.395579] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 231.402885] ata3.00: configured for UDMA/133 [ 231.408583] ata3: EH complete [ 252.015625] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 252.022758] ata4.00: failed command: SMART [ 252.028216] ata4.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 9 pio 512 in [ 252.028216] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 252.043692] ata4.00: status: { DRDY } [ 252.048141] ata4: hard resetting link [ 252.395579] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 252.401825] ata4.00: link online but device misclassified [ 252.402904] ata4.00: configured for UDMA/133 [ 252.409153] ata4: EH complete [ 273.015604] ata4: limiting SATA link speed to 1.5 Gbps [ 273.020817] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 273.029319] ata4.00: failed command: READ LOG EXT [ 273.034106] ata4.00: cmd 2f/00:01:07:00:00/00:00:00:00:00/00 tag 25 pio 512 in [ 273.034106] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 273.050055] ata4.00: status: { DRDY } [ 273.053778] ata4: hard resetting link [ 273.405581] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 273.412899] ata4.00: configured for UDMA/133 [ 273.418758] ata4: EH complete [ 876.526257] ata1: sata_mv: attempting PIO w/multiple DRQ: this may fail due to h/w errata [ 877.998228] ata2: sata_mv: attempting PIO w/multiple DRQ: this may fail due to h/w errata [ 893.598375] ata1: sata_mv: attempting PIO w/multiple DRQ: this may fail due to h/w errata [ 895.338307] ata2: sata_mv: attempting PIO w/multiple DRQ: this may fail due to h/w errata [ 898.975665] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 898.982802] ata3.00: failed command: IDENTIFY DEVICE [ 899.005610] ata3.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 29 pio 512 in [ 899.005610] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 899.035618] ata3.00: status: { DRDY } [ 899.039353] ata3: hard resetting link [ 899.385622] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 899.406218] ata3.00: configured for UDMA/133 [ 899.416454] ata3: EH complete [ 902.346638] ata1: sata_mv: attempting PIO w/multiple DRQ: this may fail due to h/w errata [ 903.736326] ata1: sata_mv: attempting PIO w/multiple DRQ: this may fail due to h/w errata [ 904.226277] ata1: sata_mv: attempting PIO w/multiple DRQ: this may fail due to h/w errata [ 906.406281] ata2: sata_mv: attempting PIO w/multiple DRQ: this may fail due to h/w errata [ 919.977889] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 919.985123] ata3.00: failed command: IDENTIFY DEVICE [ 919.991705] ata3.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 14 pio 512 in [ 919.991705] res 40/00:01:00:00:00/00:00:00:00:00/40 Emask 0x4 (timeout) [ 920.007493] ata3.00: status: { DRDY } [ 920.011862] ata3: hard resetting link [ 920.365651] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 925.365607] ata3.00: qc timeout (cmd 0xec) [ 925.369775] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 925.385659] ata3.00: revalidation failed (errno=-5) [ 925.390614] ata3: hard resetting link [ 925.735619] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 925.756214] ata3.00: configured for UDMA/133 [ 925.766498] ata3: EH complete [ 945.975618] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 945.982769] ata3.00: failed command: IDENTIFY DEVICE [ 945.989133] ata3.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 3 pio 512 in [ 945.989133] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 946.004674] ata3.00: status: { DRDY } [ 946.009150] ata3: hard resetting link [ 946.355619] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 946.374109] ata3.00: configured for UDMA/133 [ 946.386593] ata3: EH complete [ 966.988608] ata3: limiting SATA link speed to 1.5 Gbps [ 966.993819] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 967.015633] ata3.00: failed command: IDENTIFY DEVICE [ 967.030342] ata3.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 7 pio 512 in [ 967.030342] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 967.061503] ata3.00: status: { DRDY } [ 967.065257] ata3: hard resetting link [ 967.415586] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 967.422915] ata3.00: configured for UDMA/133 [ 967.428772] ata3: EH complete
Re: Debian on iomega storcenter ix4-200d: succes! February 28, 2016 05:38PM |
Admin Registered: 14 years ago Posts: 19,302 |
Re: Debian on iomega storcenter ix4-200d: succes! February 28, 2016 06:06PM |
Registered: 13 years ago Posts: 62 |
Re: Debian on iomega storcenter ix4-200d: succes! February 28, 2016 06:23PM |
Admin Registered: 14 years ago Posts: 19,302 |
Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:0xa0000@0x0(uboot),0x10000@0xa0000(env),0x228000@0xb0000(zImage),0x300000@0x2d8000(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10
Re: Debian on iomega storcenter ix4-200d: succes! February 28, 2016 06:36PM |
Registered: 13 years ago Posts: 62 |
forart
Re: Debian on iomega storcenter ix4-200d: succes! May 20, 2016 04:34PM |
Re: Debian on iomega storcenter ix4-200d: succes! May 21, 2016 02:00AM |
Admin Registered: 14 years ago Posts: 19,302 |
Re: Debian on iomega storcenter ix4-200d: succes! August 03, 2016 03:22PM |
Registered: 8 years ago Posts: 16 |
Re: Debian on iomega storcenter ix4-200d: succes! August 03, 2016 05:11PM |
Admin Registered: 14 years ago Posts: 19,302 |
Re: Debian on iomega storcenter ix4-200d: succes! August 03, 2016 06:12PM |
Registered: 8 years ago Posts: 16 |
Re: Debian on iomega storcenter ix4-200d: succes! August 03, 2016 11:30PM |
Admin Registered: 14 years ago Posts: 19,302 |
printenvand copy/paste the output to a text file.