eine
Debian on Zyxel NSA310 - another example March 20, 2016 03:29PM |
Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2and did chroot:
apt-get install qemu-user-static cp /usr/bin/qemu-arm-static /mnt/sdh2/usr/bin/ chroot /mnt/sdh2/ qemu-arm-static /bin/bashQemu-arm-static is needed to do chroot for diffrent architecture.
linux-4.4.0-kirkwood-tld-1-bodhi.tar.bz2Then I've installed two debs from tar:
linux-headers-4.4.0-kirkwood-tld-1_1.0_armel.deb linux-image-4.4.0-kirkwood-tld-1_1.0_armel.debThis operation generated initramfs. Then I've converted uImage and uInitrd. I've modified uboot to support systemd.
Re: Question about kirkwood kernel and rootfs March 20, 2016 04:09PM |
Admin Registered: 13 years ago Posts: 18,550 |
/boot/dts/kirkwood-nsa310.dtb /boot/dts/kirkwood-nsa310a.dtb /boot/dts/kirkwood-nsa310b-lmsensor-redusbled.dtb
eine
Re: Question about kirkwood kernel and rootfs March 20, 2016 04:19PM |
> /boot/dts/kirkwood-nsa310.dtb > /boot/dts/kirkwood-nsa310a.dtb > /boot/dts/kirkwood-nsa310b-lmsensor-redusbled.dtb >
Re: Question about kirkwood kernel and rootfs March 20, 2016 04:33PM |
Admin Registered: 13 years ago Posts: 18,550 |
-rw-r--r-- 1 root root 7466909 Jan 28 15:00 initrd.img-4.4.0-kirkwood-tld-1 -rw-r--r-- 1 root root 7466973 Jan 28 15:17 uInitrd.4.4.0-kirkwood-tld-1
eine
Re: Question about kirkwood kernel and rootfs March 20, 2016 04:47PM |
eine
Re: Question about kirkwood kernel and rootfs March 20, 2016 05:32PM |
Re: Question about kirkwood kernel and rootfs March 20, 2016 05:32PM |
Admin Registered: 13 years ago Posts: 18,550 |
nsa310:green:sys nsa310:green:hdd
if [ -d /sys/class/leds/nsa310:green:sys ]; then echo default-on > /sys/class/leds/nsa310:green:sys/trigger fihdd
if [ -d /sys/class/leds/nsa310:green:hdd ]; then echo ide-disk1 > /sys/class/leds/nsa310:green:hdd/trigger fihalt
if [ -d /sys/class/leds/nsa310:green:sys ]; then echo none > /sys/class/leds/nsa310:green:sys/trigger fi
Re: Question about kirkwood kernel and rootfs March 20, 2016 05:32PM |
Admin Registered: 13 years ago Posts: 18,550 |
eine
Re: Question about kirkwood kernel and rootfs March 20, 2016 06:41PM |
bootargs=console=ttyS0,115200 root=/dev/sda2 init=/bin/systemd mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)
root@nsa310:~# cat /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd1 0x0000 0x20000 0x20000 4Example output of fw_printenv:
root@nsa310:~# fw_printenv bootdelay=2 baudrate=115200 loads_echo=0 eth1addr=00:19:CB:00:51:82 ipaddr=10.4.50.165 serverip=10.4.50.5 rootpath=/mnt/ARM_FS/ netmask=255.255.255.0 nandEcc=1bit PRODUCT_NAME=NSA-310 FEATURE_BIT=00 CONTRY_TYPE=FF VENDOR_NAME=ZyXEL Communications Corp. run_diag=yes ethaddr=50:67:F0:69:AB:58 MODEL_ID=A203 arcNumber=4022 console=100000 =ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root) CASset=min ethprime=egiga1 bootargs_root=root=/dev/nfs rw bootargs_end=:::orion:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; ethmtu=1500 eth1mtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no MALLOC_len=3 bootcmd=ide reset;ext2load ide 0:1 0x800000 /uImage;ext2load ide 0:1 0xd00000 /uInitrd;bootm 0x800000 0xd00000 stdin=serial stdout=serial stderr=serial nandEnvBase=100000 mainlineLinux=yes enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no disaMvPnp=no hddPowerCtrl=no enaAutoRecovery=yes kernel_addr=0x4640000 pcieTune=no ethact=egiga1 bootargs=console=ttyS0,115200 root=/dev/sda2 init=/bin/systemd mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)
root@nsa310:~# cat /etc/rc.local #!/bin/sh -e # # rc.local # turn on LED echo default-on > /sys/class/leds/nsa310\:green\:sys/trigger echo ide-disk1 > /sys/class/leds/nsa310\:green\:hdd/trigger exit 0
apt-get install esekeydEnable deamon in:
root@nsa310:~# cat /etc/default/esekeyd # Defaults for esekeyd initscript # Start esekeyd on boot (set it to "true" to enable) START_ESEKEYD=true # Daemon options, at last config location must be present DAEMON_OPTS=/etc/esekeyd.confCreate config file:
root@nsa310:~# cat /etc/esekeyd.conf # # ESE Key Deamon 1.2.7 config file # # # example 1: to run mutt in xterm we must set DISPLAY # so the command line will be as follows: #MAIL:/bin/sh -c "DISPLAY=:0 xterm -e mutt" # # example 2: turn on/off GPS reciever when lid is open/closed #RADIO(press):echo 1 >/sys/device/platform/gps/gps_power #RADIO(release):echo 0 >/sys/device/platform/gps/gps_power # # example 3: run nautilus when both left meta and e keys are press #LEFTMETA+E:nautilus # #POWER(press): /usr/bin/logger -s -i "POWER button pushed" POWER:/sbin/shutdown -h nowFix missing realtek firmware during updating initramfs (non-free repo):
apt-get install firmware-realtekCreating zImage.fdt
cp -a zImage-4.4.0-kirkwood-tld-1 zImage.fdt cat dts/kirkwood-nsa310.dtb >> zImage.fdtGenerating and converting uImage and uInitrd:
update-initramfs -u mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-4.4.0-kirkwood-tld-1 -d initrd.img-4.4.0-kirkwood-tld-1 uInitrd mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-4.4.0-kirkwood-tld-1 -d zImage.fdt uImage
eine
Re: Question about kirkwood kernel and rootfs March 20, 2016 06:45PM |
eine
Re: Question about kirkwood kernel and rootfs March 20, 2016 06:52PM |
Re: Question about kirkwood kernel and rootfs March 21, 2016 04:05AM |
Admin Registered: 13 years ago Posts: 18,550 |
eine
Re: Question about kirkwood kernel and rootfs March 21, 2016 07:20AM |
eine
Re: Question about kirkwood kernel and rootfs March 21, 2016 08:20AM |
Re: Question about kirkwood kernel and rootfs November 22, 2017 10:05AM |
Registered: 6 years ago Posts: 12 |
root@nsa310:~# cat /etc/debian_version 9.2
root@nsa310:~# fw_printenv bootdelay=2 baudrate=115200 loads_echo=0 eth1addr=00:19:CB:00:51:82 ipaddr=10.4.50.165 serverip=10.4.50.5 rootpath=/mnt/ARM_FS/ netmask=255.255.255.0 nandEcc=1bit PRODUCT_NAME=NSA-310 FEATURE_BIT=00 CONTRY_TYPE=FF VENDOR_NAME=ZyXEL Communications Corp. run_diag=yes ethaddr=50:67:F0:69:56:9B MODEL_ID=A203 arcNumber=4022 stdin=serial stdout=serial stderr=serial console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root) mainlineLinux=yes CASset=min enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes ethprime=egiga1 netbsd_en=no vxworks_en=no bootargs_root=root=/dev/nfs rw bootargs_end=:::orion:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; disaMvPnp=no ethmtu=1500 eth1mtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 hddPowerCtrl=no netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no enaAutoRecovery=yes kernel_addr=0xc80000 pcieTune=no ethact=egiga1 bootargs=console=ttyS0,115200 root=/dev/sda2 init=/bin/systemd fsck.mode=force fsck.repair=yes mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) bootcmd=ide reset; ide read 0x800000 0x5000 0x2000; ide read 0xd00000 0xA000 0x5000; bootm 0x800000 0xd00000 root@nsa310:~# ls -l /boot/ /boot/4.13.5-kirkwood-tld1-bodhi/ /boot/: total 72552 drwxr-xr-x 3 root root 4096 Nov 22 16:29 4.13.5-kirkwood-tld1-bodhi -rw-r--r-- 1 root root 154699 Oct 7 10:53 config-4.13.5-kirkwood-tld-1 -rw-r--r-- 1 root root 140949 Jan 26 2016 config-4.4.0-kirkwood-tld-1 drwxr-xr-x 2 root root 4096 Jan 26 2016 dts -rw-r--r-- 1 root root 8510569 Nov 22 16:21 initrd.img-4.13.5-kirkwood-tld-1 -rw-r--r-- 1 root root 8867114 Nov 22 15:09 initrd.img-4.4.0-kirkwood-tld-1 -rw-r--r-- 1 root root 114393 Jan 30 2016 linux-4.4.0-kirkwood-tld-1.patch -rw-r--r-- 1 root root 1116160 Jan 30 2016 linux-dtb-4.4.0-kirkwood-tld-1.tar -rw-r--r-- 1 root root 7511582 Jan 26 2016 linux-headers-4.4.0-kirkwood-tld-1_1.0_armel.deb -rw-r--r-- 1 root root 17561216 Jan 26 2016 linux-image-4.4.0-kirkwood-tld-1_1.0_armel.deb drwx------ 2 root root 4096 Mar 20 2016 lost+found -rw------- 1 root root 2546047 Oct 7 13:26 System.map-4.13.5-kirkwood-tld-1 -rw------- 1 root root 2240040 Jan 26 2016 System.map-4.4.0-kirkwood-tld-1 -rw-r--r-- 1 root root 3167962 Nov 22 15:09 uImage -rw-r--r-- 1 root root 8867178 Nov 22 15:09 uInitrd -rw------- 1 root root 3848000 Oct 7 13:26 vmlinuz-4.13.5-kirkwood-tld-1 -rw------- 1 root root 3154832 Jan 26 2016 vmlinuz-4.4.0-kirkwood-tld-1 -rwxr-xr-x 1 root root 3154832 Jan 26 2016 zImage-4.4.0-kirkwood-tld-1 -rwxr-xr-x 1 root root 3167898 Nov 22 15:09 zImage.fdt /boot/4.13.5-kirkwood-tld1-bodhi/: total 47952 -rw-r--r-- 1 root root 154699 Oct 7 10:53 config-4.13.5-kirkwood-tld-1 drwxr-xr-x 2 root root 4096 Sep 20 10:13 dts -rw-r--r-- 1 root root 142721 Oct 9 10:05 linux-4.13.5-kirkwood-tld-1.patch -rw-r--r-- 1 root root 1300480 Oct 8 00:55 linux-dtb-4.13.5-kirkwood-tld-1.tar -rw-r--r-- 1 root root 8653960 Oct 7 13:49 linux-headers-4.13.5-kirkwood-tld-1_1.0_armel.deb -rw-r--r-- 1 root root 18669874 Oct 7 13:32 linux-image-4.13.5-kirkwood-tld-1_1.0_armel.deb -rw-r--r-- 1 root root 3860522 Nov 22 16:26 uImage -rw-r--r-- 1 root root 8510633 Nov 22 16:25 uInitrd -rwxr-xr-x 1 root root 3848000 Oct 7 08:56 zImage-4.13.5-kirkwood-tld-1 -rwxr-xr-x 1 root root 3860458 Nov 22 16:21 zImage.fdt root@nsa310:~# parted /dev/sda unit MiB print Model: ATA WDC WD20EFRX-68E (scsi) Disk /dev/sda: 1907729MiB Sector size (logical/physical): 512B/4096B Partition Table: gpt Disk Flags: Number Start End Size File system Name Flags 1 1000MiB 5096MiB 4096MiB linux-swap(v1) 2 5096MiB 46056MiB 40960MiB ext2 3 46056MiB 1907729MiB 1861673MiB btrfs root@nsa310:~# free -h total used free shared buff/cache available Mem: 241M 25M 185M 1.8M 31M 206M Swap: 4.0G 0B 4.0G root@nsa310:~# uname -a Linux nsa310 4.13.5-kirkwood-tld-1 #1 PREEMPT Fri Oct 6 23:54:39 PDT 2017 armv5tel GNU/Linux
cd /boot/4.13.5-kirkwood-tld1-bodhi/ cp -a zImage-4.13.5-kirkwood-tld-1 zImage.fdt cat dts/kirkwood-nsa310a.dtb >> zImage.fdt update-initramfs -uv mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-4.13.5-kirkwood-tld-1 -d /boot/initrd.img-4.13.5-kirkwood-tld-1 /boot/4.13.5-kirkwood-tld1-bodhi/uInitrd mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-4.13.4-kirkwood-tld-1 -d /boot/4.13.5-kirkwood-tld1-bodhi/zImage.fdt /boot/4.13.5-kirkwood-tld1-bodhi/uImage dd if=/boot/4.13.5-kirkwood-tld1-bodhi/uImage of=/dev/sda bs=1MiB seek=10 dd if=/boot/4.13.5-kirkwood-tld1-bodhi/uInitrd of=/dev/sda bs=1MiB seek=20
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** MARVELL BOARD: RD-88F6281A LE U-Boot 1.1.4 (Feb 22 2011 - 10:31:35) Marvell version: 3.4.19 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFEE0 Soc: 88F6281 A1 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Addresses 10M - 0M are saved for the U-Boot usage. Mem malloc Initialization (10M - 7M): Done NAND:128 MB Flash: 0 kB CPU : Marvell Feroceon (Rev 1) Kernel address is 0xc80000. Streaming disabled Write allocate disabled Module 0 is RGMII Module 1 is TDM USB 0: host mode PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 Net: egiga0, egiga1 [PRIME] Hit any key to stop autoboot: 0 Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found [0 0 0]: Enable DMA mode (6) Device 0 @ 0 0: Model: WDC WD20EFRX-68EUZN0 Firm: 80.00A80 Ser#: WD-WMC4M2857576 Type: Hard Disk Supports 48-bit addressing Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512) IDE read: device 0 block # 20480, count 8192 ... 8192 blocks read: OK IDE read: device 0 block # 40960, count 20480 ... 20480 blocks read: OK ## Booting image at 00800000 ... Image Name: Linux-4.13.4-kirkwood-tld-1 Created: 2017-11-22 15:26:22 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3860458 Bytes = 3.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 00d00000 ... Image Name: initramfs-4.13.5-kirkwood-tld-1 Created: 2017-11-22 15:25:20 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 8510569 Bytes = 8.1 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.13.5-kirkwood-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18)) #1 PREEMPT Fri Oct 6 23:54:39 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: ZyXEL NSA310 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] INITRD: 0x00d00000+0x0081e000 overlaps in-use memory region - disabling initrd [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda2 init=/bin/systemd fsck.mode=force fsck.repair=yes mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 246448K/262144K available (8192K kernel code, 713K rwdata, 2008K rodata, 1024K init, 284K bss, 15696K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db2744 ( 714 kB) [ 0.000000] .bss : 0xc0db91bc - 0xc0e001d4 ( 285 kB) [ 0.000000] random: get_random_u32 called from cache_alloc_refill+0x378/0x8dc with crng_init=0 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000039] Switching to timer-based delay loop, resolution 5ns [ 0.000487] Console: colour dummy device 80x30 [ 0.000519] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000539] pid_max: default: 32768 minimum: 301 [ 0.000721] Security Framework initialized [ 0.000855] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000877] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001680] CPU: Testing write buffer coherency: ok [ 0.002637] Setting up static identity map for 0x100000 - 0x100058 [ 0.002906] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.003137] Hierarchical SRCU implementation. [ 0.006308] devtmpfs: initialized [ 0.010594] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.010621] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.010984] prandom: seed boundary self test passed [ 0.015165] prandom: 100 self tests passed [ 0.015177] pinctrl core: initialized pinctrl subsystem [ 0.016194] NET: Registered protocol family 16 [ 0.016678] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.018096] cpuidle: using governor ladder [ 0.018160] cpuidle: using governor menu [ 0.018682] Feroceon L2: Enabling L2 [ 0.018725] Feroceon L2: Cache support initialised. [ 0.023951] No ATAGs? [ 0.033473] vgaarb: loaded [ 0.033788] SCSI subsystem initialized [ 0.034283] usbcore: registered new interface driver usbfs [ 0.034360] usbcore: registered new interface driver hub [ 0.034435] usbcore: registered new device driver usb [ 0.035644] clocksource: Switched to clocksource orion_clocksource [ 0.125340] VFS: Disk quotas dquot_6.6.0 [ 0.125424] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.135829] NET: Registered protocol family 2 [ 0.136558] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.136597] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.136628] TCP: Hash tables configured (established 2048 bind 2048) [ 0.136708] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.136732] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.136909] NET: Registered protocol family 1 [ 0.137322] RPC: Registered named UNIX socket transport module. [ 0.137335] RPC: Registered udp transport module. [ 0.137342] RPC: Registered tcp transport module. [ 0.137349] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.137783] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.138670] audit: initializing netlink subsys (disabled) [ 0.139127] Initialise system trusted keyrings [ 0.139177] Key type blacklist registered [ 0.139275] audit: type=2000 audit(0.133:1): state=initialized audit_enabled=0 res=1 [ 0.139352] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 0.139436] zbud: loaded [ 0.140301] NFS: Registering the id_resolver key type [ 0.140327] Key type id_resolver registered [ 0.140336] Key type id_legacy registered [ 0.140354] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.140364] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.140574] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.140772] fuse init (API version 7.26) [ 0.141118] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.141318] orangefs_init: module version upstream loaded [ 0.141329] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 2.555657] random: fast init done [ 6.056644] jitterentropy: Initialization failed with host not compliant with requirements: 2 [ 6.057472] Key type asymmetric registered [ 6.057485] Asymmetric key parser 'x509' registered [ 6.057546] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 6.057558] io scheduler noop registered [ 6.057566] io scheduler deadline registered [ 6.057642] io scheduler cfq registered (default) [ 6.058869] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 6.060854] mvebu-pcie mbus@f1000000:pcie-controller@82000000: PCI host bridge to bus 0000:00 [ 6.060876] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 6.060890] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 6.060904] pci_bus 0000:00: root bus resource [bus 00-ff] [ 6.061253] PCI: bus0: Fast back to back transfers disabled [ 6.061277] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 6.085761] PCI: bus1: Fast back to back transfers disabled [ 6.085830] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 6.085847] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff] [ 6.085867] pci 0000:01:00.0: BAR 6: assigned [mem 0xe0000000-0xe000ffff pref] [ 6.085884] pci 0000:01:00.0: BAR 4: assigned [mem 0xe0010000-0xe0013fff 64bit pref] [ 6.085909] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0014000-0xe0014fff 64bit pref] [ 6.085931] pci 0000:01:00.0: BAR 0: assigned [io 0x10000-0x100ff] [ 6.085947] pci 0000:00:01.0: PCI bridge to [bus 01] [ 6.085960] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 6.085975] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 6.086083] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 6.086604] mv_xor f1060800.xor: Marvell shared XOR driver [ 6.146413] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 6.146646] mv_xor f1060900.xor: Marvell shared XOR driver [ 6.206410] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 6.206867] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 6.208233] console [ttyS0] disabled [ 6.208302] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 6.951481] console [ttyS0] enabled [ 6.962405] loop: module loaded [ 6.966186] sata_mv f1080000.sata: slots 32 ports 2 [ 6.973802] scsi host0: sata_mv [ 6.977447] scsi host1: sata_mv [ 6.980836] ata1: SATA max UDMA/133 irq 32 [ 6.984954] ata2: SATA max UDMA/133 irq 32 [ 6.989854] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1 [ 6.996337] nand: Samsung NAND 128MiB 3,3V 8-bit [ 7.000982] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 7.008616] Scanning device for bad blocks [ 7.014515] Bad eraseblock 18 at 0x000000240000 [ 7.039585] Bad eraseblock 232 at 0x000001d00000 [ 7.046291] Bad eraseblock 254 at 0x000001fc0000 [ 7.072951] Bad eraseblock 484 at 0x000003c80000 [ 7.129425] 9 cmdlinepart partitions found on MTD device orion_nand [ 7.135745] Creating 9 MTD partitions on "orion_nand": [ 7.140916] 0x000000000000-0x000000100000 : "uboot" [ 7.147020] 0x000000100000-0x000000180000 : "uboot_env" [ 7.153400] 0x000000180000-0x000000200000 : "key_store" [ 7.159884] 0x000000200000-0x000000280000 : "info" [ 7.165772] 0x000000280000-0x000000c80000 : "etc" [ 7.171542] 0x000000c80000-0x000001680000 : "kernel_1" [ 7.177792] 0x000001680000-0x000004640000 : "rootfs1" [ 7.184209] 0x000004640000-0x000005040000 : "kernel_2" [ 7.190567] 0x000005040000-0x000008000000 : "rootfs2" [ 7.198352] libphy: Fixed MDIO Bus: probed [ 7.203354] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.209964] ehci-pci: EHCI PCI platform driver [ 7.214497] ehci-orion: EHCI orion driver [ 7.218794] orion-ehci f1050000.ehci: EHCI Host Controller [ 7.224373] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 7.232282] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 7.265670] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 7.271952] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 7.278821] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.286113] usb usb1: Product: EHCI Host Controller [ 7.291018] usb usb1: Manufacturer: Linux 4.13.5-kirkwood-tld-1 ehci_hcd [ 7.297788] usb usb1: SerialNumber: f1050000.ehci [ 7.303164] hub 1-0:1.0: USB hub found [ 7.307025] hub 1-0:1.0: 1 port detected [ 7.311596] usbcore: registered new interface driver usb-storage [ 7.318013] mousedev: PS/2 mouse device common for all mice [ 7.324179] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 7.331337] i2c /dev entries driver [ 7.337764] hidraw: raw HID events driver (C) Jiri Kosina [ 7.343552] drop_monitor: Initializing network drop monitor service [ 7.350180] NET: Registered protocol family 17 [ 7.354724] Key type dns_resolver registered [ 7.359874] registered taskstats version 1 [ 7.363993] Loading compiled-in X.509 certificates [ 7.368894] zswap: loaded using pool lzo/zbud [ 7.379531] Key type big_key registered [ 7.385236] Key type encrypted registered [ 7.390677] rtc-mv f1010300.rtc: setting system clock to 2017-11-22 15:17:30 UTC (1511363850) [ 7.495695] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 7.504446] ata1.00: ATA-9: WDC WD20EFRX-68EUZN0, 80.00A80, max UDMA/133 [ 7.511209] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 7.520591] ata1.00: configured for UDMA/133 [ 7.535331] scsi 0:0:0:0: Direct-Access ATA WDC WD20EFRX-68E 0A80 PQ: 0 ANSI: 5 [ 7.544722] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB) [ 7.553023] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 7.558419] sd 0:0:0:0: [sda] Write Protect is off [ 7.563360] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 7.621253] sda: sda1 sda2 sda3 [ 7.626578] sd 0:0:0:0: [sda] Attached SCSI disk [ 7.665685] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 7.857414] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 7.864181] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 7.871407] usb 1-1: Product: USB2.0 Hub [ 7.876258] hub 1-1:1.0: USB hub found [ 7.880415] hub 1-1:1.0: 4 ports detected [ 7.890211] ata2: SATA link down (SStatus 0 SControl F300) [ 7.934181] EXT4-fs (sda2): couldn't mount as ext3 due to feature incompatibilities [ 7.954835] EXT4-fs (sda2): mounted filesystem without journal. Opts: (null) [ 7.962051] VFS: Mounted root (ext4 filesystem) readonly on device 8:2. [ 7.981769] devtmpfs: mounted [ 7.987649] Freeing unused kernel memory: 1024K [ 8.628369] systemd[1]: Module 'ipv6' is blacklisted [ 8.673955] ip_tables: (C) 2000-2006 Netfilter Core Team [ 8.728264] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) [ 8.746963] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 9 (stretch)! [ 8.786154] systemd[1]: Set hostname to <nsa310>. [ 9.644537] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 9.676099] systemd[1]: Listening on fsck to fsckd communication Socket. [ OK ] Listening on fsck to fsckd communication Socket. [ 9.716179] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 9.749316] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ 9.809140] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 9.861534] systemd[1]: Starting File System Check on Root Device... Starting File System Check on Root Device... [ 9.916197] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Listening on udev Control Socket. [ OK ] Set up automount Arbitrary Executab…rmats File System Automount Point. [ OK ] Created slice User and Session Slice. [ OK ] Reached target Slices. Mounting Debug File System... [ OK ] Listening on udev Kernel Socket. [ OK ] Started Forward Password Requests to Wall Directory Watch. Starting Create list of required st…ce nodes for the current kernel... Starting Nameserver information manager... [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Listening on Syslog Socket. [ OK ] Listening on Journal Audit Socket. [ OK ] Created slice system-getty.slice. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Encrypted Volumes. [ OK ] Reached target Paths. [ OK ] Reached target Remote File Systems. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. Starting Journal Service... [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Debug File System. [ OK ] Started Load Kernel Modules. [ OK ] Started Create list of required sta…vice nodes for the current kernel. [ OK ] Started File System Check Daemon to report status. Starting Create Static Device Nodes in /dev... Starting Apply Kernel Variables... Mounting FUSE Control File System...) [ OK ] Mounted FUSE Control File System. [ OK ] Started Nameserver information manager. [ OK ] Started Apply Kernel Variables. [ OK ] Started Journal Service. [ OK ] Started Create Static Device Nodes in /dev. Starting udev Kernel Device Manager... [ OK ] Started udev Kernel Device Manager.e) [ 19.831485] random: crng init done complete) [ OK ] Started File System Check on Root Device. Starting Remount Root and Kernel File Systems... [ 76.685812] EXT4-fs (sda2): re-mounted. Opts: (null) [ OK ] Started Remount Root and Kernel File Systems. Starting udev Coldplug all Devices... Starting Load/Save Random Seed... Starting Flush Journal to Persistent Storage... [ OK ] Reached target Local File Systems (Pre). Mounting /tmp... [ OK ] Started Load/Save Random Seed. [ OK ] Mounted /tmp. [ 77.109608] systemd-journald[116]: Received request to flush runtime journal from PID 1 [ OK ] Reached target Local File Systems. Starting Raise network interfaces... [ OK ] Started Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. [ OK ] Reached target System Time Synchronized. Starting Update UTMP about System Boot/Shutdown... [ OK ] Started udev Coldplug all Devices. [ OK ] Started Update UTMP about System Boot/Shutdown. [ 77.890496] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [ OK ] Found device /dev/ttyS0. [ 78.202758] hwmon_vid: Unknown VRM version of your CPU [ 78.256841] lm85 0-002e: Starting monitoring [ 78.268227] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 78.269218] r8169 0000:01:00.0 eth0: RTL8168d/8111d at 0xd1949000, 00:00:00:00:00:30, XID 083000c0 IRQ 38 [ 78.269227] r8169 0000:01:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] [ 78.353429] marvell-cesa f1030000.crypto: CESA device successfully registered [ 78.354694] orion_wdt: Initial timeout 21 sec [ 78.419063] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ OK ] Found device WDC_WD20EFRX-68EUZN0 1. [ OK ] Found device WDC_WD20EFRX-68EUZN0 1. Activating swap Swap Partition... [ 79.014223] Adding 4194300k swap on /dev/sda1. Priority:-1 extents:1 across:4194300k FS [ OK ] Activated swap Swap Partition. [ OK ] Activated swap /dev/disk/by-uuid/1789cdaa-6fa3-4909-b7d9-7d3e459a0140. [ OK ] Reached target Swap. [ OK ] Reached target System Initialization. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Basic System. Starting Initialize hardware monitoring sensors... Starting Login Service... Starting System Logging Service... Starting LSB: Starts syslogd... [ OK ] Started Self Monitoring and Reporting Technology (SMART) Daemon. Starting LSB: ESE Key Daemon... Starting LSB: Starts the Name Service Cache Daemon... [ OK ] Started D-Bus System Message Bus. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Reached target Timers. [ OK ] Started System Logging Service. [ OK ] Started LSB: Starts syslogd. [ OK ] Started LSB: Starts the Name Service Cache Daemon. [ OK ] Started Initialize hardware monitoring sensors. Starting LSB: Starts klogd... [ OK ] Started LSB: Starts klogd. [ OK ] Started Login Service. [ OK ] Started LSB: ESE Key Daemon. [ 81.157046] r8169 0000:01:00.0 eth0: link down [ 81.161534] r8169 0000:01:00.0 eth0: link down [ 83.977326] r8169 0000:01:00.0 eth0: link up [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. Starting OpenVPN service... Starting Permit User Sessions... Starting Simple Network Management Protocol (SNMP) Daemon.... Starting OpenBSD Secure Shell server... [ OK ] Reached target Network is Online. Starting /etc/rc.local Compatibility... Starting LSB: LDAP connection daemon... Starting LSB: start Samba daemons for the AD DC... [ OK ] Started OpenVPN service. [ OK ] Started Permit User Sessions. [ OK ] Started Simple Network Management Protocol (SNMP) Daemon.. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started LSB: LDAP connection daemon. [ OK ] Started LSB: start Samba daemons for the AD DC. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Started Regular background program processing daemon. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Getty on tty1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... Mounting Arbitrary Executable File Formats File System... [ OK ] Mounted Arbitrary Executable File Formats File System. [ OK ] Started Update UTMP about System Runlevel Changes. Debian GNU/Linux 9 nsa310 ttyS0 nsa310 login: [ OK ] Stopped target Timers. [ OK ] Stopped Daily Cleanup of Temporary Directories. [ OK ] Stopped Daily apt upgrade and clean activities. [ OK ] Stopped Daily apt download activities. [ OK ] Stopped target Graphical Interfac Stopping Serial Getty on ttyS0... [ OK ] Stopped OpenVPN service. [ OK ] Stopped Initialize hardware monitoring sensors. Stopping D-Bus System Message Bus... Stopping Simple Network Management Protocol (SNMP) Daemon.... Stopping LSB: ESE Key Daemon... Stopping LSB: start Samba daemons for the AD DC... Stopping LSB: Starts the Name Service Cache Daemon... Stopping LSB: Starts klogd... Stopping Getty on tty1... Stopping Login Service... Stopping Self Monitoring and Reporting Technology (SMART) Daemon... Stopping OpenBSD Secure Shell server... Stopping System Logging Service... [ OK ] Stopped Login Service. [ OK ] Stopped System Logging Service. [ OK ] Stopped Self Monitoring and Reporting Technology (SMART) Daemon. [ OK ] Stopped D-Bus System Message Bus. [ OK ] Stopped OpenBSD Secure Shell server. [ OK ] Stopped Simple Network Management Protocol (SNMP) Daemon.. [ OK ] Stopped Regular background program processing daemon. [ OK ] Stopped Getty on tty1. [ OK ] Stopped Serial Getty on ttyS0. [ OK ] Stopped LSB: start Samba daemons for the AD DC. [ OK ] Stopped LSB: Starts the Name Service Cache Daemon. [ OK ] Stopped LSB: Starts klogd. Stopping LSB: Starts syslogd... [ OK ] Removed slice system-serial\x2dgetty.slice. Stopping Permit User Sessions... [ OK ] Stopped /etc/rc.local Compatibility. [ OK ] Removed slice system-getty.slice. Stopping LSB: LDAP connection daemon... [ OK ] Stopped LSB: ESE Key Daemon. [ OK ] Stopped LSB: Starts syslogd. [ OK ] Stopped Permit User Sessions. [ OK ] Stopped LSB: LDAP connection daemon. [ OK ] Stopped target System Time Synchronized. [ OK ] Stopped target Network is Online. [ OK ] Stopped target Network. Stopping Raise network interfaces... [ OK ] Stopped target Basic System. [ OK ] Stopped target Sockets. [ OK ] Closed Syslog Socket. [ OK ] Closed D-Bus System Message Bus Socket. [ OK ] Stopped target Slices. [ OK ] Removed slice User and Session Slice. [ OK ] Stopped target Paths. [ OK ] Stopped target System Initialization. [ OK ] Stopped target Encrypted Volumes. [ OK ] Stopped Forward Password Requests to Wall Directory Watch. [ OK ] Stopped Dispatch Password Requests to Console Directory Watch. [ OK ] Stopped target Swap. Deactivating swap Swap Partition... Deactivating swap /dev/disk/by-id/wwn-0x50014ee0ae6ff021-part1... Stopping Load/Save Random Seed... Stopping Update UTMP about System Boot/Shutdown... [ OK ] Stopped target Remote File Systems. [ OK ] Deactivated swap /dev/disk/by-path/platform-f1080000.sata-ata-1-part1. [ OK ] Deactivated swap /dev/disk/by-partu…da65d-18f8-4ee7-9d87-2f86cc555d84. [ OK ] Deactivated swap /dev/disk/by-id/wwn-0x50014ee0ae6ff021-part1. [ OK ] Deactivated swap /dev/disk/by-id/at…FRX-68EUZN0_WD-WMC4M2857576-part1. [ OK ] Deactivated swap Swap Partition. [ OK ] Deactivated swap /dev/disk/by-uuid/…9cdaa-6fa3-4909-b7d9-7d3e459a0140. [ OK ] Stopped Load/Save Random Seed. [ OK ] Stopped Update UTMP about System Boot/Shutdown. [ OK ] Stopped Create Volatile Files and Directories. [ OK ] Stopped Raise network interfaces. [ OK ] Stopped Apply Kernel Variables. [ OK ] Stopped target Local File Systems. Unmounting /tmp... [ OK ] Stopped Load Kernel Modules. [ OK ] Unmounted /tmp. [ OK ] Reached target Unmount All Filesystems. [ OK ] Stopped target Local File Systems (Pre). [ OK ] Stopped Create Static Device Nodes in /dev. [ OK ] Stopped Remount Root and Kernel File Systems. [ OK ] Reached target Shutdown. [ 306.762421] systemd-shutdow: 32 output lines suppressed due to ratelimiting [ 306.945848] systemd-shutdown[1]: Sending SIGTERM to remaining processes... [ 306.963714] systemd-journald[116]: Received SIGTERM from PID 1 (systemd-shutdow). [ 307.006562] systemd-shutdown[1]: Sending SIGKILL to remaining processes... [ 307.022576] systemd-shutdown[1]: Unmounting file systems. [ 307.029132] systemd-shutdown[1]: Remounting '/' read-only with options 'block_validity,delalloc,barrier,user_xattr,acl'. [ 307.105762] EXT4-fs (sda2): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr,acl [ 307.325470] systemd-shutdown[1]: Remounting '/' read-only with options 'block_validity,delalloc,barrier,user_xattr,acl'. [ 307.336931] EXT4-fs (sda2): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr,acl [ 307.345448] systemd-shutdown[1]: All filesystems unmounted. [ 307.351207] systemd-shutdown[1]: Deactivating swaps. [ 307.356458] systemd-shutdown[1]: All swaps deactivated. [ 307.361732] systemd-shutdown[1]: Detaching loop devices. [ 307.393747] systemd-shutdown[1]: All loop devices detached. [ 307.445794] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 307.451179] sd 0:0:0:0: [sda] Stopping disk [ 307.876067] reboot: Power down
[ 112.169306] ------------[ cut here ]------------ [ 112.173962] WARNING: CPU: 0 PID: 522 at fs/filesystems.c:281 get_fs_type+0xa0/0xe4 [ 112.183271] request_module fs-btrfs succeeded, but still no fs? [ 112.190216] Modules linked in: binfmt_misc evdev fixed sg uas lm85 hwmon_vid orion_wdt marvell_cesa r8169 gpio_keys uio_pdrv_genirq uio ip_tables x_tables autofs4 [ 112.205856] CPU: 0 PID: 522 Comm: mount Not tainted 4.13.5-kirkwood-tld-1 #1 [ 112.212933] Hardware name: Marvell Kirkwood (Flattened Device Tree) [ 112.220646] [<c010ea24>] (unwind_backtrace) from [<c010ab28>] (show_stack+0x10/0x14) [ 112.229373] [<c010ab28>] (show_stack) from [<c011812c>] (__warn+0xe0/0xfc) [ 112.237236] [<c011812c>] (__warn) from [<c011817c>] (warn_slowpath_fmt+0x34/0x44) [ 112.244764] [<c011817c>] (warn_slowpath_fmt) from [<c0250f38>] (get_fs_type+0xa0/0xe4) [ 112.254113] [<c0250f38>] (get_fs_type) from [<c02549d4>] (do_mount+0x664/0xb30) [ 112.262359] [<c02549d4>] (do_mount) from [<c02550e4>] (SyS_mount+0x70/0x98) [ 112.270262] [<c02550e4>] (SyS_mount) from [<c0106ec0>] (ret_fast_syscall+0x0/0x38) [ 112.278767] ---[ end trace 8fb1adfba3d8f851 ]---
mount -t btrfs /dev/sda3 /srv/backup/ -o defaults,autodefrag,compressBtrfs module somehow didn't load, I had to do it manually. It's not a big deal for me. Great work, congrats.
Re: Question about kirkwood kernel and rootfs November 22, 2017 04:41PM |
Admin Registered: 13 years ago Posts: 18,550 |