Re: Debian on CISCO ON100-K9 September 20, 2016 11:07PM |
Admin Registered: 13 years ago Posts: 18,495 |
ON100_K9> setenv ethact egiga1
Re: Debian on CISCO ON100-K9 September 20, 2016 11:49PM |
Registered: 9 years ago Posts: 1,516 |
Re: Debian on CISCO ON100-K9 September 21, 2016 01:29AM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: Debian on CISCO ON100-K9 September 21, 2016 09:21PM |
Registered: 9 years ago Posts: 437 |
> version > printenv ethaddr > printenv ethact > setenv ipaddr 192.168.178.110 > setenv gatewayip 192.168.178.1 > setenv netmask 255.255.255.0 > mii device > mii info 0 > mii info 1 > setenv pingr 'for pingstat in 1 2 3 4 5; do; sleep > 1; ping 192.168.178.1; done' > run pingr > ping 8.8.8.8 > mii dump 0 0-5 >>
> version > printenv eth1addr > setenv ethact egiga1 > setenv ipaddr 192.168.178.110 > setenv gatewayip 192.168.178.1 > setenv netmask 255.255.255.0 > mii device > mii info 0 > mii info 1 > setenv pingr 'for pingstat in 1 2 3 4 5; do; sleep > 1; ping 192.168.178.1; done' > run pingr > ping 8.8.8.8 > mii dump 1 0-5 >
U-Boot 2016.05-tld-2.18 (Sep 20 2016 - 13:37:24 -0700) Cisco ON100_K9 SoC: Kirkwood 88F6282_A1 DRAM: 512 MiB WARNING: Caches not enabled NAND: 512 MiB MMC: kwsdio: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: Marvell MV88E1310 PHY initialized egiga0 Waiting for PHY auto negotiation to complete....... done Marvell MV88E1310 PHY initialized egiga1 Waiting for PHY auto negotiation to complete................. TIMEOUT ! egiga0, egiga1 Hit any key to stop autoboot: 0 ON100_K9> version U-Boot 2016.05-tld-2.18 (Sep 20 2016 - 13:37:24 -0700) Cisco ON100_K9 gcc (Debian 4.9.2-10) 4.9.2 GNU ld (GNU Binutils for Debian) 2.25 ON100_K9> printenv ethaddr ethaddr=b6:d0:5e:0f:a1:17 ON100_K9> printenv ethact ethact=egiga0 ON100_K9> setenv ipaddr 192.168.11.15 ON100_K9> setenv gatewayip 192.168.11.1 ON100_K9> setenv netmask 255.255.255.0 ON100_K9> mii device MII devices: 'egiga0' 'egiga1' Current device: 'egiga0' ON100_K9> mii info 0 PHY 0x00: OUI = 0x5043, Model = 0x29, Rev = 0x00, 1000baseT, FDX ON100_K9> mii info 1 PHY 0x01: OUI = 0x5043, Model = 0x29, Rev = 0x00, 10baseT, HDX ON100_K9> setenv pingr 'for pingstat in 1 2 3 4 5; do; sleep 1; ping 192.168.11.1; done' ON100_K9> run pingr Using egiga0 device host 192.168.11.1 is alive Using egiga0 device host 192.168.11.1 is alive Using egiga0 device host 192.168.11.1 is alive Using egiga0 device host 192.168.11.1 is alive Using egiga0 device host 192.168.11.1 is alive ON100_K9> ping 8.8.8.8 Using egiga0 device host 8.8.8.8 is alive ON100_K9> mii dump 0 0-5 0. (1000) -- PHY control register -- (8000:0000) 0.15 = 0 reset (4000:0000) 0.14 = 0 loopback (2040:0000) 0. 6,13 = b00 speed selection = 10 Mbps (1000:1000) 0.12 = 1 A/N enable (0800:0000) 0.11 = 0 power-down (0400:0000) 0.10 = 0 isolate (0200:0000) 0. 9 = 0 restart A/N (0100:0000) 0. 8 = 0 duplex = half (0080:0000) 0. 7 = 0 collision test enable (003f:0000) 0. 5- 0 = 0 (reserved) 1. (796d) -- PHY status register -- (8000:0000) 1.15 = 0 100BASE-T4 able (4000:4000) 1.14 = 1 100BASE-X full duplex able (2000:2000) 1.13 = 1 100BASE-X half duplex able (1000:1000) 1.12 = 1 10 Mbps full duplex able (0800:0800) 1.11 = 1 10 Mbps half duplex able (0400:0000) 1.10 = 0 100BASE-T2 full duplex able (0200:0000) 1. 9 = 0 100BASE-T2 half duplex able (0100:0100) 1. 8 = 1 extended status (0080:0000) 1. 7 = 0 (reserved) (0040:0040) 1. 6 = 1 MF preamble suppression (0020:0020) 1. 5 = 1 A/N complete (0010:0000) 1. 4 = 0 remote fault (0008:0008) 1. 3 = 1 A/N able (0004:0004) 1. 2 = 1 link status (0002:0000) 1. 1 = 0 jabber detect (0001:0001) 1. 0 = 1 extended capabilities 2. (0141) -- PHY ID 1 register -- (ffff:0141) 2.15- 0 = 321 OUI portion 3. (0e90) -- PHY ID 2 register -- (fc00:0c00) 3.15-10 = 3 OUI portion (03f0:0290) 3. 9- 4 = 41 manufacturer part number (000f:0000) 3. 3- 0 = 0 manufacturer rev. number 4. (01e1) -- Autonegotiation advertisement register -- (8000:0000) 4.15 = 0 next page able (4000:0000) 4.14 = 0 (reserved) (2000:0000) 4.13 = 0 remote fault (1000:0000) 4.12 = 0 (reserved) (0800:0000) 4.11 = 0 asymmetric pause (0400:0000) 4.10 = 0 pause enable (0200:0000) 4. 9 = 0 100BASE-T4 able (0100:0100) 4. 8 = 1 100BASE-TX full duplex able (0080:0080) 4. 7 = 1 100BASE-TX able (0040:0040) 4. 6 = 1 10BASE-T full duplex able (0020:0020) 4. 5 = 1 10BASE-T able (001f:0001) 4. 4- 0 = 1 selector = IEEE 802.3 5. (cde1) -- Autonegotiation partner abilities register -- (8000:8000) 5.15 = 1 next page able (4000:4000) 5.14 = 1 acknowledge (2000:0000) 5.13 = 0 remote fault (1000:0000) 5.12 = 0 (reserved) (0800:0800) 5.11 = 1 asymmetric pause able (0400:0400) 5.10 = 1 pause able (0200:0000) 5. 9 = 0 100BASE-T4 able (0100:0100) 5. 8 = 1 100BASE-X full duplex able (0080:0080) 5. 7 = 1 100BASE-TX able (0040:0040) 5. 6 = 1 10BASE-T full duplex able (0020:0020) 5. 5 = 1 10BASE-T able (001f:0001) 5. 4- 0 = 1 selector = IEEE 802.3 ON100_K9>
U-Boot 2016.05-tld-2.18 (Sep 20 2016 - 13:37:24 -0700) Cisco ON100_K9 SoC: Kirkwood 88F6282_A1 DRAM: 512 MiB WARNING: Caches not enabled NAND: 512 MiB MMC: kwsdio: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: Marvell MV88E1310 PHY initialized egiga0 Waiting for PHY auto negotiation to complete................. TIMEOUT ! Marvell MV88E1310 PHY initialized egiga1 Waiting for PHY auto negotiation to complete....... done egiga0, egiga1 Hit any key to stop autoboot: 0 ON100_K9> version U-Boot 2016.05-tld-2.18 (Sep 20 2016 - 13:37:24 -0700) Cisco ON100_K9 gcc (Debian 4.9.2-10) 4.9.2 GNU ld (GNU Binutils for Debian) 2.25 ON100_K9> printenv eth1addr eth1addr=a6:1c:1a:49:fe:34 ON100_K9> setenv ethact egiga1 ON100_K9> setenv ipaddr 192.168.11.20 ON100_K9> setenv gatewayip 192.168.11.1 ON100_K9> setenv netmask 255.255.255.0 ON100_K9> mii device MII devices: 'egiga0' 'egiga1' Current device: 'egiga0' ON100_K9> mii info 0 PHY 0x00: OUI = 0x5043, Model = 0x29, Rev = 0x00, 10baseT, HDX ON100_K9> mii info 1 PHY 0x01: OUI = 0x5043, Model = 0x29, Rev = 0x00, 1000baseT, FDX ON100_K9> setenv pingr 'for pingstat in 1 2 3 4 5; do; sleep 1; ping 192.168.11.1; done' ON100_K9> run pingr Using egiga1 device host 192.168.11.1 is alive Using egiga1 device host 192.168.11.1 is alive Using egiga1 device host 192.168.11.1 is alive Using egiga1 device host 192.168.11.1 is alive Using egiga1 device host 192.168.11.1 is alive ON100_K9> ping 8.8.8.8 Using egiga1 device host 8.8.8.8 is alive ON100_K9> mii dump 1 0-5 0. (1000) -- PHY control register -- (8000:0000) 0.15 = 0 reset (4000:0000) 0.14 = 0 loopback (2040:0000) 0. 6,13 = b00 speed selection = 10 Mbps (1000:1000) 0.12 = 1 A/N enable (0800:0000) 0.11 = 0 power-down (0400:0000) 0.10 = 0 isolate (0200:0000) 0. 9 = 0 restart A/N (0100:0000) 0. 8 = 0 duplex = half (0080:0000) 0. 7 = 0 collision test enable (003f:0000) 0. 5- 0 = 0 (reserved) 1. (796d) -- PHY status register -- (8000:0000) 1.15 = 0 100BASE-T4 able (4000:4000) 1.14 = 1 100BASE-X full duplex able (2000:2000) 1.13 = 1 100BASE-X half duplex able (1000:1000) 1.12 = 1 10 Mbps full duplex able (0800:0800) 1.11 = 1 10 Mbps half duplex able (0400:0000) 1.10 = 0 100BASE-T2 full duplex able (0200:0000) 1. 9 = 0 100BASE-T2 half duplex able (0100:0100) 1. 8 = 1 extended status (0080:0000) 1. 7 = 0 (reserved) (0040:0040) 1. 6 = 1 MF preamble suppression (0020:0020) 1. 5 = 1 A/N complete (0010:0000) 1. 4 = 0 remote fault (0008:0008) 1. 3 = 1 A/N able (0004:0004) 1. 2 = 1 link status (0002:0000) 1. 1 = 0 jabber detect (0001:0001) 1. 0 = 1 extended capabilities 2. (0141) -- PHY ID 1 register -- (ffff:0141) 2.15- 0 = 321 OUI portion 3. (0e90) -- PHY ID 2 register -- (fc00:0c00) 3.15-10 = 3 OUI portion (03f0:0290) 3. 9- 4 = 41 manufacturer part number (000f:0000) 3. 3- 0 = 0 manufacturer rev. number 4. (01e1) -- Autonegotiation advertisement register -- (8000:0000) 4.15 = 0 next page able (4000:0000) 4.14 = 0 (reserved) (2000:0000) 4.13 = 0 remote fault (1000:0000) 4.12 = 0 (reserved) (0800:0000) 4.11 = 0 asymmetric pause (0400:0000) 4.10 = 0 pause enable (0200:0000) 4. 9 = 0 100BASE-T4 able (0100:0100) 4. 8 = 1 100BASE-TX full duplex able (0080:0080) 4. 7 = 1 100BASE-TX able (0040:0040) 4. 6 = 1 10BASE-T full duplex able (0020:0020) 4. 5 = 1 10BASE-T able (001f:0001) 4. 4- 0 = 1 selector = IEEE 802.3 5. (cde1) -- Autonegotiation partner abilities register -- (8000:8000) 5.15 = 1 next page able (4000:4000) 5.14 = 1 acknowledge (2000:0000) 5.13 = 0 remote fault (1000:0000) 5.12 = 0 (reserved) (0800:0800) 5.11 = 1 asymmetric pause able (0400:0400) 5.10 = 1 pause able (0200:0000) 5. 9 = 0 100BASE-T4 able (0100:0100) 5. 8 = 1 100BASE-X full duplex able (0080:0080) 5. 7 = 1 100BASE-TX able (0040:0040) 5. 6 = 1 10BASE-T full duplex able (0020:0020) 5. 5 = 1 10BASE-T able (001f:0001) 5. 4- 0 = 1 selector = IEEE 802.3 ON100_K9>
Re: Debian on CISCO ON100-K9 September 22, 2016 01:28AM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: Debian on CISCO ON100-K9 September 22, 2016 08:28PM |
Registered: 9 years ago Posts: 1,516 |
U-Boot 2016.05-tld-2.18 (Sep 20 2016 - 13:37:24 -0700) Cisco ON100_K9 SoC: Kirkwood 88F6282_A1 DRAM: 512 MiB WARNING: Caches not enabled NAND: 512 MiB MMC: kwsdio: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: Marvell MV88E1310 PHY initialized egiga0 Waiting for PHY auto negotiation to complete..... done Marvell MV88E1310 PHY initialized egiga1 Waiting for PHY auto negotiation to complete................. TIMEOUT ! egiga0, egiga1 Hit any key to stop autoboot: 0 ON100_K9> version U-Boot 2016.05-tld-2.18 (Sep 20 2016 - 13:37:24 -0700) Cisco ON100_K9 gcc (Debian 4.9.2-10) 4.9.2 GNU ld (GNU Binutils for Debian) 2.25 ON100_K9> printenv ethaddr ethaddr=b6:d0:5e:0f:a1:17 ON100_K9> printenv ethact ethact=egiga0 ON100_K9> setenv ipaddr 192.168.178.110 ON100_K9> setenv gatewayip 192.168.178.1 ON100_K9> setenv netmask 255.255.255.0 ON100_K9> mii device MII devices: 'egiga0' 'egiga1' Current device: 'egiga0' ON100_K9> mii info 0 PHY 0x00: OUI = 0x5043, Model = 0x29, Rev = 0x00, 1000baseT, FDX ON100_K9> mii info 1 PHY 0x01: OUI = 0x5043, Model = 0x29, Rev = 0x00, 10baseT, HDX ON100_K9> setenv pingr 'for pingstat in 1 2 3 4 5; do; sleep 1; ping 192.168.178.1; done' ON100_K9> run pingr Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.178.1 is not alive Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.178.1 is not alive Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.178.1 is not alive Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.178.1 is not alive Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.178.1 is not alive ON100_K9> ping 8.8.8.8 Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 8.8.8.8 is not alive ON100_K9> mii dump 0 0-5 0. (1000) -- PHY control register -- (8000:0000) 0.15 = 0 reset (4000:0000) 0.14 = 0 loopback (2040:0000) 0. 6,13 = b00 speed selection = 10 Mbps (1000:1000) 0.12 = 1 A/N enable (0800:0000) 0.11 = 0 power-down (0400:0000) 0.10 = 0 isolate (0200:0000) 0. 9 = 0 restart A/N (0100:0000) 0. 8 = 0 duplex = half (0080:0000) 0. 7 = 0 collision test enable (003f:0000) 0. 5- 0 = 0 (reserved) 1. (796d) -- PHY status register -- (8000:0000) 1.15 = 0 100BASE-T4 able (4000:4000) 1.14 = 1 100BASE-X full duplex able (2000:2000) 1.13 = 1 100BASE-X half duplex able (1000:1000) 1.12 = 1 10 Mbps full duplex able (0800:0800) 1.11 = 1 10 Mbps half duplex able (0400:0000) 1.10 = 0 100BASE-T2 full duplex able (0200:0000) 1. 9 = 0 100BASE-T2 half duplex able (0100:0100) 1. 8 = 1 extended status (0080:0000) 1. 7 = 0 (reserved) (0040:0040) 1. 6 = 1 MF preamble suppression (0020:0020) 1. 5 = 1 A/N complete (0010:0000) 1. 4 = 0 remote fault (0008:0008) 1. 3 = 1 A/N able (0004:0004) 1. 2 = 1 link status (0002:0000) 1. 1 = 0 jabber detect (0001:0001) 1. 0 = 1 extended capabilities 2. (0141) -- PHY ID 1 register -- (ffff:0141) 2.15- 0 = 321 OUI portion 3. (0e90) -- PHY ID 2 register -- (fc00:0c00) 3.15-10 = 3 OUI portion (03f0:0290) 3. 9- 4 = 41 manufacturer part number (000f:0000) 3. 3- 0 = 0 manufacturer rev. number 4. (01e1) -- Autonegotiation advertisement register -- (8000:0000) 4.15 = 0 next page able (4000:0000) 4.14 = 0 (reserved) (2000:0000) 4.13 = 0 remote fault (1000:0000) 4.12 = 0 (reserved) (0800:0000) 4.11 = 0 asymmetric pause (0400:0000) 4.10 = 0 pause enable (0200:0000) 4. 9 = 0 100BASE-T4 able (0100:0100) 4. 8 = 1 100BASE-TX full duplex able (0080:0080) 4. 7 = 1 100BASE-TX able (0040:0040) 4. 6 = 1 10BASE-T full duplex able (0020:0020) 4. 5 = 1 10BASE-T able (001f:0001) 4. 4- 0 = 1 selector = IEEE 802.3 5. (dde1) -- Autonegotiation partner abilities register -- (8000:8000) 5.15 = 1 next page able (4000:4000) 5.14 = 1 acknowledge (2000:0000) 5.13 = 0 remote fault (1000:1000) 5.12 = 1 (reserved) (0800:0800) 5.11 = 1 asymmetric pause able (0400:0400) 5.10 = 1 pause able (0200:0000) 5. 9 = 0 100BASE-T4 able (0100:0100) 5. 8 = 1 100BASE-X full duplex able (0080:0080) 5. 7 = 1 100BASE-TX able (0040:0040) 5. 6 = 1 10BASE-T full duplex able (0020:0020) 5. 5 = 1 10BASE-T able (001f:0001) 5. 4- 0 = 1 selector = IEEE 802.3 ON100_K9>
U-Boot 2016.05-tld-2.18 (Sep 20 2016 - 13:37:24 -0700) Cisco ON100_K9 SoC: Kirkwood 88F6282_A1 DRAM: 512 MiB WARNING: Caches not enabled NAND: 512 MiB MMC: kwsdio: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: Marvell MV88E1310 PHY initialized egiga0 Waiting for PHY auto negotiation to complete................. TIMEOUT ! Marvell MV88E1310 PHY initialized egiga1 Waiting for PHY auto negotiation to complete..... done egiga0, egiga1 Hit any key to stop autoboot: 0 ON100_K9> version U-Boot 2016.05-tld-2.18 (Sep 20 2016 - 13:37:24 -0700) Cisco ON100_K9 gcc (Debian 4.9.2-10) 4.9.2 GNU ld (GNU Binutils for Debian) 2.25 ON100_K9> printenv eth1addr eth1addr=a6:1c:1a:49:fe:34 ON100_K9> setenv ethact egiga1 ON100_K9> setenv ipaddr 192.168.178.110 ON100_K9> setenv gatewayip 192.168.178.1 ON100_K9> setenv netmask 255.255.255.0 ON100_K9> mii device MII devices: 'egiga0' 'egiga1' Current device: 'egiga0' ON100_K9> mii info 0 PHY 0x00: OUI = 0x5043, Model = 0x29, Rev = 0x00, 10baseT, HDX ON100_K9> mii info 1 PHY 0x01: OUI = 0x5043, Model = 0x29, Rev = 0x00, 1000baseT, FDX ON100_K9> setenv pingr 'for pingstat in 1 2 3 4 5; do; sleep 1; ping 192.168.178.1; done' ON100_K9> run pingr Using egiga1 device host 192.168.178.1 is alive Using egiga1 device host 192.168.178.1 is alive Using egiga1 device host 192.168.178.1 is alive Using egiga1 device host 192.168.178.1 is alive Using egiga1 device host 192.168.178.1 is alive ON100_K9> ping 8.8.8.8 Using egiga1 device host 8.8.8.8 is alive ON100_K9> mii dump 1 0-5 0. (1000) -- PHY control register -- (8000:0000) 0.15 = 0 reset (4000:0000) 0.14 = 0 loopback (2040:0000) 0. 6,13 = b00 speed selection = 10 Mbps (1000:1000) 0.12 = 1 A/N enable (0800:0000) 0.11 = 0 power-down (0400:0000) 0.10 = 0 isolate (0200:0000) 0. 9 = 0 restart A/N (0100:0000) 0. 8 = 0 duplex = half (0080:0000) 0. 7 = 0 collision test enable (003f:0000) 0. 5- 0 = 0 (reserved) 1. (796d) -- PHY status register -- (8000:0000) 1.15 = 0 100BASE-T4 able (4000:4000) 1.14 = 1 100BASE-X full duplex able (2000:2000) 1.13 = 1 100BASE-X half duplex able (1000:1000) 1.12 = 1 10 Mbps full duplex able (0800:0800) 1.11 = 1 10 Mbps half duplex able (0400:0000) 1.10 = 0 100BASE-T2 full duplex able (0200:0000) 1. 9 = 0 100BASE-T2 half duplex able (0100:0100) 1. 8 = 1 extended status (0080:0000) 1. 7 = 0 (reserved) (0040:0040) 1. 6 = 1 MF preamble suppression (0020:0020) 1. 5 = 1 A/N complete (0010:0000) 1. 4 = 0 remote fault (0008:0008) 1. 3 = 1 A/N able (0004:0004) 1. 2 = 1 link status (0002:0000) 1. 1 = 0 jabber detect (0001:0001) 1. 0 = 1 extended capabilities 2. (0141) -- PHY ID 1 register -- (ffff:0141) 2.15- 0 = 321 OUI portion 3. (0e90) -- PHY ID 2 register -- (fc00:0c00) 3.15-10 = 3 OUI portion (03f0:0290) 3. 9- 4 = 41 manufacturer part number (000f:0000) 3. 3- 0 = 0 manufacturer rev. number 4. (01e1) -- Autonegotiation advertisement register -- (8000:0000) 4.15 = 0 next page able (4000:0000) 4.14 = 0 (reserved) (2000:0000) 4.13 = 0 remote fault (1000:0000) 4.12 = 0 (reserved) (0800:0000) 4.11 = 0 asymmetric pause (0400:0000) 4.10 = 0 pause enable (0200:0000) 4. 9 = 0 100BASE-T4 able (0100:0100) 4. 8 = 1 100BASE-TX full duplex able (0080:0080) 4. 7 = 1 100BASE-TX able (0040:0040) 4. 6 = 1 10BASE-T full duplex able (0020:0020) 4. 5 = 1 10BASE-T able (001f:0001) 4. 4- 0 = 1 selector = IEEE 802.3 5. (dde1) -- Autonegotiation partner abilities register -- (8000:8000) 5.15 = 1 next page able (4000:4000) 5.14 = 1 acknowledge (2000:0000) 5.13 = 0 remote fault (1000:1000) 5.12 = 1 (reserved) (0800:0800) 5.11 = 1 asymmetric pause able (0400:0400) 5.10 = 1 pause able (0200:0000) 5. 9 = 0 100BASE-T4 able (0100:0100) 5. 8 = 1 100BASE-X full duplex able (0080:0080) 5. 7 = 1 100BASE-TX able (0040:0040) 5. 6 = 1 10BASE-T full duplex able (0020:0020) 5. 5 = 1 10BASE-T able (001f:0001) 5. 4- 0 = 1 selector = IEEE 802.3 ON100_K9>
Re: Debian on CISCO ON100-K9 September 22, 2016 08:46PM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: Debian on CISCO ON100-K9 September 22, 2016 10:21PM |
Registered: 9 years ago Posts: 1,516 |
setenv ethact egiga1One Test lacks the "egiga1" part. I wondered to myself if "egiga0" or something should be there.
Re: Debian on CISCO ON100-K9 September 22, 2016 10:49PM |
Admin Registered: 13 years ago Posts: 18,495 |
> setenv ethact egiga1 >> One Test lacks the "egiga1" part. I wondered to
Re: Debian on CISCO ON100-K9 September 22, 2016 11:35PM |
Registered: 9 years ago Posts: 1,516 |
U-Boot 2016.05-tld-2.18 (Sep 20 2016 - 13:37:24 -0700) Cisco ON100_K9 SoC: Kirkwood 88F6282_A1 DRAM: 512 MiB WARNING: Caches not enabled NAND: 512 MiB MMC: kwsdio: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: Marvell MV88E1310 PHY initialized egiga0 Waiting for PHY auto negotiation to complete...... done Marvell MV88E1310 PHY initialized egiga1 Waiting for PHY auto negotiation to complete................. TIMEOUT ! egiga0, egiga1 Hit any key to stop autoboot: 0 ON100_K9> version U-Boot 2016.05-tld-2.18 (Sep 20 2016 - 13:37:24 -0700) Cisco ON100_K9 gcc (Debian 4.9.2-10) 4.9.2 GNU ld (GNU Binutils for Debian) 2.25 ON100_K9> printenv ethaddr ethaddr=b6:d0:5e:0f:a1:17 ON100_K9> printenv ethact ethact=egiga0 ON100_K9> setenv ipaddr 192.168.178.110 ON100_K9> setenv gatewayip 192.168.178.1 ON100_K9> setenv netmask 255.255.255.0 ON100_K9> mii device MII devices: 'egiga0' 'egiga1' Current device: 'egiga0' ON100_K9> mii info 0t PHY 0x00: OUI = 0x5043, Model = 0x29, Rev = 0x00, 1000baseT, FDX ON100_K9> mii info 1 PHY 0x01: OUI = 0x5043, Model = 0x29, Rev = 0x00, 10baseT, HDX ON100_K9> setenv pingr 'for pingstat in 1 2 3 4 5; do; sleep 1; ping 192.168.178.1; done' ON100_K9> run pingr Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.178.1 is not alive Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.178.1 is not alive Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.178.1 is not alive Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.178.1 is not alive Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.178.1 is not alive ON100_K9> ping 8.8.8.8 Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 8.8.8.8 is not alive ON100_K9> mii dump 0 0-5 0. (1000) -- PHY control register -- (8000:0000) 0.15 = 0 reset (4000:0000) 0.14 = 0 loopback (2040:0000) 0. 6,13 = b00 speed selection = 10 Mbps (1000:1000) 0.12 = 1 A/N enable (0800:0000) 0.11 = 0 power-down (0400:0000) 0.10 = 0 isolate (0200:0000) 0. 9 = 0 restart A/N (0100:0000) 0. 8 = 0 duplex = half (0080:0000) 0. 7 = 0 collision test enable (003f:0000) 0. 5- 0 = 0 (reserved) 1. (796d) -- PHY status register -- (8000:0000) 1.15 = 0 100BASE-T4 able (4000:4000) 1.14 = 1 100BASE-X full duplex able (2000:2000) 1.13 = 1 100BASE-X half duplex able (1000:1000) 1.12 = 1 10 Mbps full duplex able (0800:0800) 1.11 = 1 10 Mbps half duplex able (0400:0000) 1.10 = 0 100BASE-T2 full duplex able (0200:0000) 1. 9 = 0 100BASE-T2 half duplex able (0100:0100) 1. 8 = 1 extended status (0080:0000) 1. 7 = 0 (reserved) (0040:0040) 1. 6 = 1 MF preamble suppression (0020:0020) 1. 5 = 1 A/N complete (0010:0000) 1. 4 = 0 remote fault (0008:0008) 1. 3 = 1 A/N able (0004:0004) 1. 2 = 1 link status (0002:0000) 1. 1 = 0 jabber detect (0001:0001) 1. 0 = 1 extended capabilities 2. (0141) -- PHY ID 1 register -- (ffff:0141) 2.15- 0 = 321 OUI portion 3. (0e90) -- PHY ID 2 register -- (fc00:0c00) 3.15-10 = 3 OUI portion (03f0:0290) 3. 9- 4 = 41 manufacturer part number (000f:0000) 3. 3- 0 = 0 manufacturer rev. number 4. (01e1) -- Autonegotiation advertisement register -- (8000:0000) 4.15 = 0 next page able (4000:0000) 4.14 = 0 (reserved) (2000:0000) 4.13 = 0 remote fault (1000:0000) 4.12 = 0 (reserved) (0800:0000) 4.11 = 0 asymmetric pause (0400:0000) 4.10 = 0 pause enable (0200:0000) 4. 9 = 0 100BASE-T4 able (0100:0100) 4. 8 = 1 100BASE-TX full duplex able (0080:0080) 4. 7 = 1 100BASE-TX able (0040:0040) 4. 6 = 1 10BASE-T full duplex able (0020:0020) 4. 5 = 1 10BASE-T able (001f:0001) 4. 4- 0 = 1 selector = IEEE 802.3 5. (dde1) -- Autonegotiation partner abilities register -- (8000:8000) 5.15 = 1 next page able (4000:4000) 5.14 = 1 acknowledge (2000:0000) 5.13 = 0 remote fault (1000:1000) 5.12 = 1 (reserved) (0800:0800) 5.11 = 1 asymmetric pause able (0400:0400) 5.10 = 1 pause able (0200:0000) 5. 9 = 0 100BASE-T4 able (0100:0100) 5. 8 = 1 100BASE-X full duplex able (0080:0080) 5. 7 = 1 100BASE-TX able (0040:0040) 5. 6 = 1 10BASE-T full duplex able (0020:0020) 5. 5 = 1 10BASE-T able (001f:0001) 5. 4- 0 = 1 selector = IEEE 802.3 ON100_K9>
Re: Debian on CISCO ON100-K9 September 23, 2016 12:20AM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: Debian on CISCO ON100-K9 September 23, 2016 12:39AM |
Registered: 9 years ago Posts: 1,516 |
Re: Debian on CISCO ON100-K9 September 23, 2016 02:19PM |
Registered: 9 years ago Posts: 1,516 |
Re: Debian on CISCO ON100-K9 September 23, 2016 02:52PM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: Debian on CISCO ON100-K9 September 23, 2016 03:15PM |
Registered: 9 years ago Posts: 1,516 |
./kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2016.05-tld-2.18.on100_k9.mtd0.kwb -p
Re: Debian on CISCO ON100-K9 September 23, 2016 05:10PM |
Admin Registered: 13 years ago Posts: 18,495 |
> ./kwboot -t -B 115200 /dev/ttyUSB0 -b > uboot.2016.05-tld-2.18.on100_k9.mtd0.kwb -p >>
Re: Debian on CISCO ON100-K9 September 23, 2016 06:08PM |
Registered: 9 years ago Posts: 1,516 |
U-Boot 2016.05-tld-2.18 (Sep 20 2016 - 13:37:24 -0700) Cisco ON100_K9 SoC: Kirkwood 88F6282_A1 DRAM: 512 MiB WARNING: Caches not enabled NAND: 512 MiB MMC: kwsdio: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: Marvell MV88E1310 PHY initialized egiga0 Waiting for PHY auto negotiation to complete..... done Marvell MV88E1310 PHY initialized egiga1 Waiting for PHY auto negotiation to complete................. TIMEOUT ! egiga0, egiga1 Hit any key to stop autoboot: 0 ON100_K9> version U-Boot 2016.05-tld-2.18 (Sep 20 2016 - 13:37:24 -0700) Cisco ON100_K9 gcc (Debian 4.9.2-10) 4.9.2 GNU ld (GNU Binutils for Debian) 2.25 ON100_K9> printenv ethaddr ethaddr=b6:d0:5e:0f:a1:17 ON100_K9> printenv ethact ethact=egiga0 ON100_K9> setenv ipaddr 192.168.178.110 ON100_K9> setenv gatewayip 192.168.178.1 ON100_K9> setenv netmask 255.255.255.0 ON100_K9> mii device MII devices: 'egiga0' 'egiga1' Current device: 'egiga0' ON100_K9> mii info 0 PHY 0x00: OUI = 0x5043, Model = 0x29, Rev = 0x00, 1000baseT, FDX ON100_K9> mii info 1 PHY 0x01: OUI = 0x5043, Model = 0x29, Rev = 0x00, 10baseT, HDX ON100_K9> setenv pingr 'for pingstat in 1 2 3 4 5; do; sleep 1; ping 192.168.178.1; done' ON100_K9> run pingr Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.178.1 is not alive Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.178.1 is not alive Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.178.1 is not alive Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.178.1 is not alive Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 192.168.178.1 is not alive ON100_K9> ping 8.8.8.8 Using egiga0 device ARP Retry count exceeded; starting again ping failed; host 8.8.8.8 is not alive ON100_K9> mii dump 0 0-5 0. (1000) -- PHY control register -- (8000:0000) 0.15 = 0 reset (4000:0000) 0.14 = 0 loopback (2040:0000) 0. 6,13 = b00 speed selection = 10 Mbps (1000:1000) 0.12 = 1 A/N enable (0800:0000) 0.11 = 0 power-down (0400:0000) 0.10 = 0 isolate (0200:0000) 0. 9 = 0 restart A/N (0100:0000) 0. 8 = 0 duplex = half (0080:0000) 0. 7 = 0 collision test enable (003f:0000) 0. 5- 0 = 0 (reserved) 1. (796d) -- PHY status register -- (8000:0000) 1.15 = 0 100BASE-T4 able (4000:4000) 1.14 = 1 100BASE-X full duplex able (2000:2000) 1.13 = 1 100BASE-X half duplex able (1000:1000) 1.12 = 1 10 Mbps full duplex able (0800:0800) 1.11 = 1 10 Mbps half duplex able (0400:0000) 1.10 = 0 100BASE-T2 full duplex able (0200:0000) 1. 9 = 0 100BASE-T2 half duplex able (0100:0100) 1. 8 = 1 extended status (0080:0000) 1. 7 = 0 (reserved) (0040:0040) 1. 6 = 1 MF preamble suppression (0020:0020) 1. 5 = 1 A/N complete (0010:0000) 1. 4 = 0 remote fault (0008:0008) 1. 3 = 1 A/N able (0004:0004) 1. 2 = 1 link status (0002:0000) 1. 1 = 0 jabber detect (0001:0001) 1. 0 = 1 extended capabilities 2. (0141) -- PHY ID 1 register -- (ffff:0141) 2.15- 0 = 321 OUI portion 3. (0e90) -- PHY ID 2 register -- (fc00:0c00) 3.15-10 = 3 OUI portion (03f0:0290) 3. 9- 4 = 41 manufacturer part number (000f:0000) 3. 3- 0 = 0 manufacturer rev. number 4. (01e1) -- Autonegotiation advertisement register -- (8000:0000) 4.15 = 0 next page able (4000:0000) 4.14 = 0 (reserved) (2000:0000) 4.13 = 0 remote fault (1000:0000) 4.12 = 0 (reserved) (0800:0000) 4.11 = 0 asymmetric pause (0400:0000) 4.10 = 0 pause enable (0200:0000) 4. 9 = 0 100BASE-T4 able (0100:0100) 4. 8 = 1 100BASE-TX full duplex able (0080:0080) 4. 7 = 1 100BASE-TX able (0040:0040) 4. 6 = 1 10BASE-T full duplex able (0020:0020) 4. 5 = 1 10BASE-T able (001f:0001) 4. 4- 0 = 1 selector = IEEE 802.3 5. (dde1) -- Autonegotiation partner abilities register -- (8000:8000) 5.15 = 1 next page able (4000:4000) 5.14 = 1 acknowledge (2000:0000) 5.13 = 0 remote fault (1000:1000) 5.12 = 1 (reserved) (0800:0800) 5.11 = 1 asymmetric pause able (0400:0400) 5.10 = 1 pause able (0200:0000) 5. 9 = 0 100BASE-T4 able (0100:0100) 5. 8 = 1 100BASE-X full duplex able (0080:0080) 5. 7 = 1 100BASE-TX able (0040:0040) 5. 6 = 1 10BASE-T full duplex able (0020:0020) 5. 5 = 1 10BASE-T able (001f:0001) 5. 4- 0 = 1 selector = IEEE 802.3 ON100_K9>
Re: Debian on CISCO ON100-K9 September 24, 2016 03:08PM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: Debian on CISCO ON100-K9 September 25, 2016 10:22AM |
Registered: 9 years ago Posts: 1,516 |
Re: Debian on CISCO ON100-K9 September 26, 2016 01:15PM |
Registered: 9 years ago Posts: 437 |
Re: Debian on CISCO ON100-K9 September 27, 2016 11:35AM |
Admin Registered: 13 years ago Posts: 18,495 |
EDITED September 27, 2016 11:43PM |
Registered: 9 years ago Posts: 1,516 |
Re: Debian on CISCO ON100-K9 September 28, 2016 04:37PM |
Registered: 9 years ago Posts: 437 |
Re: Debian on CISCO ON100-K9 January 12, 2018 01:23AM |
Registered: 9 years ago Posts: 437 |
Re: Debian on CISCO ON100-K9 January 12, 2018 11:05PM |
Registered: 9 years ago Posts: 437 |
root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 00200000 00200000 "uBoot" mtd1: 00200000 00200000 "dualboot" mtd2: 00600000 00200000 "kernel1" mtd3: 00800000 00200000 "rootfs1" mtd4: 00600000 00200000 "kernel2" mtd5: 00800000 00200000 "rootfs2" mtd6: 1d600000 00200000 "datafs" mtd7: 00a00000 00200000 "misc" root@debian:~# flash_erase /dev/mtd0 0 4 flash_erase: error!: /dev/mtd0 error 13 (Permission denied) root@debian:~# flash_unlock /dev/mtd0 flash_unlock: error!: could not open: /dev/mtd0 error 13 (Permission denied) root@debian:~#
Re: Debian on CISCO ON100-K9 January 12, 2018 11:50PM |
Registered: 9 years ago Posts: 437 |
U-Boot 2016.05-tld-2.18 (Sep 20 2016 - 13:37:24 -0700) Cisco ON100_K9 SoC: Kirkwood 88F6282_A1 DRAM: 512 MiB WARNING: Caches not enabled NAND: 512 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: Marvell MV88E1310 PHY initialized egiga0 Waiting for PHY auto negotiation to complete....... done Marvell MV88E1310 PHY initialized egiga1 Waiting for PHY auto negotiation to complete................. TIMEOUT ! egiga0, egiga1 Error: egiga1 address not set. Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Reset IDE: ide_preinit failed ** First descriptor is NOT a primary desc on 0:1 ** MMC rescan: current device # 0 initialized OK no USB devices available no IDE devices available ## Unknown partition table type 0 loading envs from mmc 0 ... ** No partition table - mmc 0 ** running scan_disk ... Scan device usb device usb 0:1 ** Bad device usb 0 ** device usb 1:1 ** Bad device usb 1 ** device usb 2:1 ** Bad device usb 2 ** device usb 3:1 ** Bad device usb 3 ** Scan device ide Reset IDE: ide_preinit failed device ide 0:1 ** Bad device size - ide 0 ** device ide 1:1 ** Bad device size - ide 1 ** device ide 2:1 ** Bad device ide 2 ** device ide 3:1 ** Bad device ide 3 ** Scan device mmc ** First descriptor is NOT a primary desc on 0:1 ** MMC rescan: current device # 0 initialized OK device mmc 0:1 ** No partition table - mmc 0 ** device mmc 1:1 MMC Device 1 not found MMC Device 1 not found ** Bad device mmc 1 ** device mmc 2:1 MMC Device 2 not found MMC Device 2 not found ** Bad device mmc 2 ** device mmc 3:1 MMC Device 3 not found MMC Device 3 not found ** Bad device mmc 3 ** loading uImage ... ** Bad device usb 0 ** loading uInitrd ... ** Bad device usb 0 ** loading DTB /boot/dts/kirkwood-on100.dtb ... ** Bad device usb 0 ** Wrong Image Format for bootm command Error occured, error code = 112 ERROR: can't get kernel image! ON100_K9>
U-Boot 2016.05-tld-2.18 (Sep 20 2016 - 13:37:24 -0700) Cisco ON100_K9 SoC: Kirkwood 88F6282_A1 DRAM: 512 MiB WARNING: Caches not enabled NAND: 512 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: Marvell MV88E1310 PHY initialized egiga0 Waiting for PHY auto negotiation to complete....... done Marvell MV88E1310 PHY initialized egiga1 Waiting for PHY auto negotiation to complete................. TIMEOUT ! egiga0, egiga1 Error: egiga1 address not set. Hit any key to stop autoboot: 10 9 8 7 6 5 4 3 2 1 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Reset IDE: ide_preinit failed ** First descriptor is NOT a primary desc on 0:1 ** MMC rescan: current device # 0 initialized OK Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 60592384 45544d62-01 83 loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** no IDE devices available ## Unknown partition table type 0 loading envs from mmc 0 ... ** No partition table - mmc 0 ** running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 123 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 3821592 bytes read in 305 ms (11.9 MiB/s) loading uInitrd ... 7245696 bytes read in 506 ms (13.7 MiB/s) loading DTB /boot/dts/kirkwood-on100.dtb ... 11666 bytes read in 941 ms (11.7 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.12.1-kirkwood-tld-1 Created: 2017-07-20 8:11:24 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3821528 Bytes = 3.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.12.1-kirkwood-tld-1 Created: 2017-07-24 0:18:23 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7245632 Bytes = 6.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 1f422000, end 1fb0af40 ... OK Loading Device Tree to 1f41c000, end 1f421d91 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.1-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: Cisco Systems ON100 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 499272K/524288K available (8192K kernel code, 716K rwdata, 1972K rodata, 1024K init, 288K bss, 25016K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db3274 ( 717 kB) [ 0.000000] .bss : 0xc0db9b9c - 0xc0e01e60 ( 289 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000007] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000041] Switching to timer-based delay loop, resolution 5ns [ 0.000469] Console: colour dummy device 80x30 [ 0.000503] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000523] pid_max: default: 32768 minimum: 301 [ 0.000707] Security Framework initialized [ 0.000816] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000836] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001671] CPU: Testing write buffer coherency: ok [ 0.002733] Setting up static identity map for 0x100000 - 0x100058 [ 0.002977] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1 [ 0.006011] devtmpfs: initialized [ 0.009850] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.009878] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.010336] prandom: seed boundary self test passed [ 0.013144] prandom: 100 self tests passed [ 0.013155] pinctrl core: initialized pinctrl subsystem [ 0.014279] NET: Registered protocol family 16 [ 0.014696] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.016254] cpuidle: using governor ladder [ 0.016331] cpuidle: using governor menu [ 0.016711] Feroceon L2: Enabling L2 [ 0.016754] Feroceon L2: Cache support initialised. [ 0.017066] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.017154] [Firmware Info]: /ocp@f1000000/ethernet-controller@76000/ethernet1-port@0: local-mac-address is not set [ 0.020949] No ATAGs? [ 0.028158] vgaarb: loaded [ 0.028428] SCSI subsystem initialized [ 0.028823] usbcore: registered new interface driver usbfs [ 0.028891] usbcore: registered new interface driver hub [ 0.028939] usbcore: registered new device driver usb [ 0.029873] clocksource: Switched to clocksource orion_clocksource [ 0.102842] VFS: Disk quotas dquot_6.6.0 [ 0.102926] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.111315] NET: Registered protocol family 2 [ 0.112015] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.112087] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.112153] TCP: Hash tables configured (established 4096 bind 4096) [ 0.112230] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.112255] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.112418] NET: Registered protocol family 1 [ 0.112797] RPC: Registered named UNIX socket transport module. [ 0.112807] RPC: Registered udp transport module. [ 0.112813] RPC: Registered tcp transport module. [ 0.112818] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.113026] Unpacking initramfs... [ 0.631226] Freeing initrd memory: 7076K [ 0.631347] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.632214] audit: initializing netlink subsys (disabled) [ 0.632662] Initialise system trusted keyrings [ 0.632713] Key type blacklist registered [ 0.632794] audit: type=2000 audit(0.622:1): state=initialized audit_enabled=0 res=1 [ 0.632884] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.632946] zbud: loaded [ 0.633767] NFS: Registering the id_resolver key type [ 0.633791] Key type id_resolver registered [ 0.633798] Key type id_legacy registered [ 0.633813] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.633821] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.634007] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.634167] fuse init (API version 7.26) [ 0.634480] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.634689] orangefs_init: module version upstream loaded [ 0.634698] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 2.559879] random: fast init done [ 4.994747] Key type asymmetric registered [ 4.994763] Asymmetric key parser 'x509' registered [ 4.994828] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 4.994838] io scheduler noop registered [ 4.994845] io scheduler deadline registered [ 4.994920] io scheduler cfq registered (default) [ 4.996020] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 4.997437] mv_xor f1060800.xor: Marvell shared XOR driver [ 5.050463] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 5.050686] mv_xor f1060900.xor: Marvell shared XOR driver [ 5.110459] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 5.110858] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 5.111918] console [ttyS0] disabled [ 5.111983] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 5.722090] console [ttyS0] enabled [ 5.732696] loop: module loaded [ 5.736788] nand: Could not find valid ONFI parameter page; aborting [ 5.743251] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xdc [ 5.749630] nand: Hynix NAND 512MiB 3,3V 8-bit [ 5.754116] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 5.761741] Scanning device for bad blocks [ 5.820928] Bad eraseblock 723 at 0x000005a60000 [ 5.825680] Bad eraseblock 725 at 0x000005aa0000 [ 5.952628] Bad eraseblock 2332 at 0x000012380000 [ 6.091301] Bad eraseblock 4091 at 0x00001ff60000 [ 6.096140] Bad eraseblock 4093 at 0x00001ffa0000 [ 6.101002] Bad eraseblock 4095 at 0x00001ffe0000 [ 6.105735] 4 cmdlinepart partitions found on MTD device orion_nand [ 6.112042] Creating 4 MTD partitions on "orion_nand": [ 6.117202] 0x000000000000-0x000000100000 : "u-boot" [ 6.123182] 0x000000100000-0x000000500000 : "uImage" [ 6.129121] 0x000000500000-0x000002500000 : "rootfs" [ 6.135258] 0x000002500000-0x000020000000 : "data" [ 6.144326] libphy: Fixed MDIO Bus: probed [ 6.149128] libphy: orion_mdio_bus: probed [ 6.161567] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 6.260908] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 64:00:f1:20:e0:da [ 6.360763] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:00:00:00:00:00 [ 6.369592] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 6.376197] ehci-pci: EHCI PCI platform driver [ 6.380725] ehci-orion: EHCI orion driver [ 6.384917] orion-ehci f1050000.ehci: EHCI Host Controller [ 6.390478] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 6.398299] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 6.429899] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 6.436153] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 6.442994] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.450265] usb usb1: Product: EHCI Host Controller [ 6.455158] usb usb1: Manufacturer: Linux 4.12.1-kirkwood-tld-1 ehci_hcd [ 6.461904] usb usb1: SerialNumber: f1050000.ehci [ 6.467178] hub 1-0:1.0: USB hub found [ 6.471024] hub 1-0:1.0: 1 port detected [ 6.475475] usbcore: registered new interface driver usb-storage [ 6.481840] mousedev: PS/2 mouse device common for all mice [ 6.487910] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 6.494981] i2c /dev entries driver [ 6.499761] hidraw: raw HID events driver (C) Jiri Kosina [ 6.505555] drop_monitor: Initializing network drop monitor service [ 6.512094] NET: Registered protocol family 17 [ 6.516629] Key type dns_resolver registered [ 6.521565] registered taskstats version 1 [ 6.525677] Loading compiled-in X.509 certificates [ 6.530562] zswap: loaded using pool lzo/zbud [ 6.543713] Key type big_key registered [ 6.555676] Key type encrypted registered [ 6.561066] rtc-mv f1010300.rtc: setting system clock to 2018-01-13 05:30:00 UTC (1515821400) [ 6.573944] Freeing unused kernel memory: 1024K Loading, please wait... starting version 232 [ 6.829976] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 7.033306] usb 1-1: New USB device found, idVendor=0930, idProduct=6544 [ 7.047970] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7.063312] usb 1-1: Product: TransMemory [ 7.067783] usb 1-1: Manufacturer: TOSHIBA [ 7.079992] usb 1-1: SerialNumber: 7071BCD10782CF50E2CF8316 [ 7.093541] usb-storage 1-1:1.0: USB Mass Storage device detected [ 7.099693] mmc0: host does not support reading read-only switch, assuming write-enable [ 7.102800] mmc0: new high speed SDHC card at address aaaa [ 7.136521] scsi host0: usb-storage 1-1:1.0 [ 7.231417] usbcore: registered new interface driver uas [ 7.240032] mmcblk0: mmc0:aaaa ADLCD 29.7 GiB [ 7.256978] mmcblk0: p1 Begin: Loading essential drivers ... done. [ 8.212024] scsi 0:0:0:0: Direct-Access TOSHIBA TransMemory 1.00 PQ: 0 ANSI: 4 [ 8.225124] sd 0:0:0:0: [sda] 60594432 512-byte logical blocks: (31.0 GB/28.9 GiB) [ 8.240510] sd 0:0:0:0: [sda] Write Protect is off [ 8.249478] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 8.268561] sda: sda1 [ 8.276103] sd 0:0:0:0: [sda] Attached SCSI removable disk Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Warning: fsck not present, so skipping root file system [ 17.536071] EXT4-fs (sda1): INFO: recovery required on readonly filesystem [ 17.543137] EXT4-fs (sda1): write access will be enabled during recovery [ 25.803089] EXT4-fs (sda1): recovery complete [ 25.812349] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [[36minfo[39;49m] Using makefile-style concurrent boot in runlevel S. [....] Setting hostname to 'debian'...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232 [?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Synthesizing the initial hotplug events...[?25l[?1c7[1G[ 27.629683] kirkwood-pinctrl f1010000.pin-controller: pin PIN31 already requested by f1076000.ethernet-controller; cannot claim for gpio_keys [[32m ok [39;49m8[?25h[?0cdone. [....] Waiting for /dev to be fully populated...[ 27.768630] kirkwood-pinctrl f1010000.pin-controller: pin-31 (gpio_keys) status -22 [ 27.816340] (NULL device *): hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info(). [ 27.948546] kirkwood-pinctrl f1010000.pin-controller: could not request pin 31 (PIN31) from group mpp31 on device f1010000.pin-controller [ 28.012834] marvell-cesa f1030000.crypto: CESA device successfully registered [ 28.013948] orion_wdt: Initial timeout 21 sec [ 28.099619] gpio-keys gpio_keys: Error applying setting, reverse things back [ 28.167005] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 28.217159] gpio-keys: probe of gpio_keys failed with error -22 [?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Activating swap:[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [ 29.174896] EXT4-fs (sda1): re-mounted. Opts: (null) [....] Will now check root file system:fsck from util-linux 2.29.2 [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sda1 e2fsck 1.43.4 (31-Jan-2017) rootfs: clean, 14547/1896832 files, 297372/7574048 blocks [?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [ 29.446793] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 29.797378] random: crng init done [....] Will now activate lvm and md swap:[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [[36minfo[39;49m] Will now check all file systems. fsck from util-linux 2.29.2 Checking all file systems. LABEL=rootfs is mounted [....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Cleaning up temporary files...[....] Cleaning /tmp...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. /tmp[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Will now mount local filesystems:[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Will now activate swapfile swap:[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Checking minimum space in /tmp...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Cleaning up temporary files...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Setting kernel variables...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Initializing random number generator...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5 Copyright 2004-2016 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/64:00:f1:20:e0:da Sending on LPF/eth0/64:00:f1:20:e0:da Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4 [ 34.929854] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 39.860152] NET: Registered protocol family 10 [ 39.867256] Segment Routing with IPv6 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4 DHCPREQUEST of 192.168.11.239 on eth0 to 255.255.255.255 port 67 DHCPOFFER of 192.168.11.239 from 192.168.11.1 DHCPACK of 192.168.11.239 from 192.168.11.1 bound to 192.168.11.239 -- renewal in 17830 seconds. [?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Starting RPC port mapper daemon: rpcbind[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting NFS common utilities: statd idmapd[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Cleaning up temporary files...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. INIT: Entering runlevel: 2 [[36minfo[39;49m] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1335 (syslogd) [?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting system message bus: dbus[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting NFS common utilities: statd idmapd[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Not starting NFS kernel daemon: no exports. ...[?25l[?1c7[1G[[33mwarn[39;49m8[?25h[?0c [33m(warning).[39;49m [....] Starting NTP server: ntpd[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting OpenBSD Secure Shell server: sshd[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1333 (klogd) [?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Running local boot scripts (/etc/rc.local)[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. Debian GNU/Linux 9 debian ttyS0 debian login:
Unpacking libicu57:armel (57.1-6+deb9u1) over (57.1-6) ... [ 427.103177] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b [ 427.103177] [ 427.112369] CPU: 0 PID: 1 Comm: init Not tainted 4.12.1-kirkwood-tld-1 #1 [ 427.119180] Hardware name: Marvell Kirkwood (Flattened Device Tree) [ 427.125503] [<c010ea54>] (unwind_backtrace) from [<c010ab48>] (show_stack+0x10/0x14) [ 427.133296] [<c010ab48>] (show_stack) from [<c01dba9c>] (panic+0xb0/0x250) [ 427.140211] [<c01dba9c>] (panic) from [<c011a3e8>] (do_exit+0x5e0/0xa64) [ 427.146943] [<c011a3e8>] (do_exit) from [<c011bc18>] (do_group_exit+0x4c/0xec) [ 427.154203] [<c011bc18>] (do_group_exit) from [<c0125f1c>] (get_signal+0x5ac/0x658) [ 427.161899] [<c0125f1c>] (get_signal) from [<c010a00c>] (do_signal+0x8c/0x3bc) [ 427.169152] [<c010a00c>] (do_signal) from [<c010a4a4>] (do_work_pending+0x5c/0xd0) [ 427.176755] [<c010a4a4>] (do_work_pending) from [<c0107090>] (slow_work_pending+0xc/0x20) [ 427.184976] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b [ 427.184976]
Re: Debian on CISCO ON100-K9 January 13, 2018 04:04AM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: Debian on CISCO ON100-K9 January 13, 2018 07:31AM |
Registered: 6 years ago Posts: 2 |
Re: Debian on CISCO ON100-K9 January 14, 2018 02:34AM |
Registered: 9 years ago Posts: 437 |
Re: Debian on CISCO ON100-K9 January 14, 2018 09:50AM |
Registered: 6 years ago Posts: 2 |