Re: Pogoplug E02 Debian Linux Installation Guide October 22, 2017 06:13AM |
Registered: 8 years ago Posts: 88 |
Re: Pogoplug E02 Debian Linux Installation Guide October 22, 2017 06:23AM |
Admin Registered: 13 years ago Posts: 18,575 |
arcNumber=3542 machid=dd6 ethaddr=00:25:31:04:80:8C disks=0 1 2 3 4 5 6 7 preboot_nc=setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi preboot=run preboot_nc ipaddr=192.168.222.168 serverip=192.168.222.103 load_initrd=ext2load usb 0:1 0x1100000 /boot/uInitrd load_uimage=ext2load usb 0:1 0x800000 /boot/uImage usb_boot=run load_dtb; run load_uimage; if run load_initrd; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 - 0x1c00000; fi load_db=load_dtb=ext2load usb 0:1 0x1c00000 /boot/dts/kirkwood-pogo_e02.dtb load_dtb=ext2load usb 0:1 0x1c00000 /boot/dts/kirkwood-pogo_e02.dtb
load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage
usb_boot=run load_dtb; run load_uimage; if run load_initrd; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 - 0x1c00000; fi load_db=load_dtb=ext2load usb 0:1 0x1c00000 /boot/dts/kirkwood-pogo_e02.dtb
Re: Pogoplug E02 Debian Linux Installation Guide October 22, 2017 06:28AM |
Admin Registered: 13 years ago Posts: 18,575 |
devices=usb
Re: Pogoplug E02 Debian Linux Installation Guide October 22, 2017 06:30AM |
Admin Registered: 13 years ago Posts: 18,575 |
Re: Pogoplug E02 Debian Linux Installation Guide October 22, 2017 06:31AM |
Registered: 8 years ago Posts: 88 |
Re: Pogoplug E02 Debian Linux Installation Guide October 23, 2017 01:26AM |
Registered: 8 years ago Posts: 88 |
root@debian:~# root@debian:~# root@debian:~# fw_printenv bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 ethact=egiga0 if_netconsole=ping $serverip led_error=orange blinking led_exit=green off led_init=green blinking dtb_file=/boot/dts/kirkwood-pogo_e02.dtb load_dtb_addr=0x1c00000 load_initrd_addr=0x1100000 load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi usb_ready_retry=15 arcNumber=3542 machid=dd6 ethaddr=00:25:31:04:80:8C disks=0 1 2 3 4 5 6 7 preboot_nc=setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi preboot=run preboot_nc ipaddr=192.168.222.168 devices=usb load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage serverip=192.168.222.164 root@debian:~# root@debian:~#
U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:23:43 -0700) Pogo E02 SoC: Kirkwood 88F6281_A0 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 Using egiga0 device Abort ping failed; host 192.168.222.103 is not alive Hit any key to stop autoboot: 0 PogoE02> boot starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Unknown command 'ide' - try 'help' Unknown command 'mmc' - try 'help' Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 7829504 3fd1c278-01 83 Boot loading envs from usb 0 ... 88 bytes read in 274 ms (0 Bytes/s) Unknown command 'ide' - try 'help' Unknown command 'mmc' - try 'help' importing envs ... running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 253 ms (0 Bytes/s) Found bootable drive on usb 0 3821592 bytes read in 468 ms (7.8 MiB/s) 7245696 bytes read in 622 ms (11.1 MiB/s) ** File not found /boot/dts/kirkwood-pogo_e02.dtb ** ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.12.1-kirkwood-tld-1 Created: 2017-07-20 8:11:24 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3821528 Bytes = 3.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.12.1-kirkwood-tld-1 Created: 2017-07-24 0:18:23 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7245632 Bytes = 6.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK Using machid 0xdd6 from environment Starting kernel ... Uncompressing Linux... done, booting the kernel. Error: unrecognized/unsupported machine ID (r1 = 0x00000dd6). Available machine support: ID (hex) NAME ffffffff Generic DT based system ffffffff Marvell Kirkwood (Flattened Device Tree) Please check your kernel config and/or bootloader.
PogoE02> boot starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Unknown command 'ide' - try 'help' Unknown command 'mmc' - try 'help' Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 7829504 3fd1c278-01 83 Boot loading envs from usb 0 ... 88 bytes read in 274 ms (0 Bytes/s) Unknown command 'ide' - try 'help' Unknown command 'mmc' - try 'help' importing envs ... running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 253 ms (0 Bytes/s) Found bootable drive on usb 0 3821592 bytes read in 469 ms (7.8 MiB/s) 7245696 bytes read in 623 ms (11.1 MiB/s) 10444 bytes read in 1263 ms (7.8 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.12.1-kirkwood-tld-1 Created: 2017-07-20 8:11:24 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3821528 Bytes = 3.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.12.1-kirkwood-tld-1 Created: 2017-07-24 0:18:23 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7245632 Bytes = 6.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f42b000, end 0fb13f40 ... OK Loading Device Tree to 0f425000, end 0f42a8cb ... OK Using machid 0xdd6 from environment Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.1-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: CloudEngines Pogoplug E02 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 239376K/262144K available (8192K kernel code, 716K rwdata, 1972K rodata, 1024K init, 288K bss, 22768K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db3274 ( 717 kB) [ 0.000000] .bss : 0xc0db9b9c - 0xc0e01e60 ( 289 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000007] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000042] Switching to timer-based delay loop, resolution 5ns [ 0.000509] Console: colour dummy device 80x30 [ 0.000542] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000564] pid_max: default: 32768 minimum: 301 [ 0.000762] Security Framework initialized [ 0.000886] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000905] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001767] CPU: Testing write buffer coherency: ok [ 0.002816] Setting up static identity map for 0x100000 - 0x100058 [ 0.003077] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.006375] devtmpfs: initialized [ 0.010318] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.010347] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.010751] prandom: seed boundary self test passed [ 0.014508] prandom: 100 self tests passed [ 0.014521] pinctrl core: initialized pinctrl subsystem [ 0.015669] NET: Registered protocol family 16 [ 0.016146] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.017741] cpuidle: using governor ladder [ 0.017813] cpuidle: using governor menu [ 0.018239] Feroceon L2: Enabling L2 [ 0.018286] Feroceon L2: Cache support initialised. [ 0.018657] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.023173] No ATAGs? [ 0.032252] vgaarb: loaded [ 0.032578] SCSI subsystem initialized [ 0.033051] usbcore: registered new interface driver usbfs [ 0.033128] usbcore: registered new interface driver hub [ 0.033209] usbcore: registered new device driver usb [ 0.034310] clocksource: Switched to clocksource orion_clocksource [ 0.123918] VFS: Disk quotas dquot_6.6.0 [ 0.124003] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.134704] NET: Registered protocol family 2 [ 0.135456] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.135495] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.135526] TCP: Hash tables configured (established 2048 bind 2048) [ 0.135615] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.135640] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.135817] NET: Registered protocol family 1 [ 0.136236] RPC: Registered named UNIX socket transport module. [ 0.136249] RPC: Registered udp transport module. [ 0.136257] RPC: Registered tcp transport module. [ 0.136264] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.136507] Unpacking initramfs... [ 0.797328] Freeing initrd memory: 7076K [ 0.797469] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.798441] audit: initializing netlink subsys (disabled) [ 0.798934] Initialise system trusted keyrings [ 0.798991] Key type blacklist registered [ 0.799089] audit: type=2000 audit(0.794:1): state=initialized audit_enabled=0 res=1 [ 0.799184] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 0.799254] zbud: loaded [ 0.800245] NFS: Registering the id_resolver key type [ 0.800271] Key type id_resolver registered [ 0.800280] Key type id_legacy registered [ 0.800298] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.800308] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.800503] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.800701] fuse init (API version 7.26) [ 0.801072] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.801343] orangefs_init: module version upstream loaded [ 0.801355] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 2.554317] random: fast init done [ 6.676411] Key type asymmetric registered [ 6.676430] Asymmetric key parser 'x509' registered [ 6.676500] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 6.676511] io scheduler noop registered [ 6.676519] io scheduler deadline registered [ 6.676602] io scheduler cfq registered (default) [ 6.677911] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 6.679773] mv_xor f1060800.xor: Marvell shared XOR driver [ 6.735050] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 6.735284] mv_xor f1060900.xor: Marvell shared XOR driver [ 6.795061] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 6.795490] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 6.796738] console [ttyS0] disabled [ 6.796808] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 7.397072] console [ttyS0] enabled [ 7.409113] loop: module loaded [ 7.413424] nand: Could not find valid ONFI parameter page; aborting [ 7.419898] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 7.426313] nand: Hynix NAND 128MiB 3,3V 8-bit [ 7.430780] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 7.438411] Scanning device for bad blocks [ 7.551465] 4 cmdlinepart partitions found on MTD device orion_nand [ 7.557780] Creating 4 MTD partitions on "orion_nand": [ 7.562945] 0x000000000000-0x000000100000 : "u-boot" [ 7.569143] 0x000000100000-0x000000500000 : "uImage" [ 7.575351] 0x000000500000-0x000002500000 : "rootfs" [ 7.581688] 0x000002500000-0x000008000000 : "data" [ 7.589456] libphy: Fixed MDIO Bus: probed [ 7.594462] libphy: orion_mdio_bus: probed [ 7.603527] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 8.706042] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:04:80:8c [ 8.714943] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.721525] ehci-pci: EHCI PCI platform driver [ 8.726077] ehci-orion: EHCI orion driver [ 8.730300] orion-ehci f1050000.ehci: EHCI Host Controller [ 8.735876] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 8.743739] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 8.774345] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 8.780639] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 8.787488] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.794767] usb usb1: Product: EHCI Host Controller [ 8.799664] usb usb1: Manufacturer: Linux 4.12.1-kirkwood-tld-1 ehci_hcd [ 8.806415] usb usb1: SerialNumber: f1050000.ehci [ 8.811910] hub 1-0:1.0: USB hub found [ 8.815778] hub 1-0:1.0: 1 port detected [ 8.820409] usbcore: registered new interface driver usb-storage [ 8.826806] mousedev: PS/2 mouse device common for all mice [ 9.174344] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 9.366115] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 9.372861] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 9.380069] usb 1-1: Product: USB2.0 Hub [ 9.384912] hub 1-1:1.0: USB hub found [ 9.388990] hub 1-1:1.0: 4 ports detected [ 9.714336] usb 1-1.1: new high-speed USB device number 3 using orion-ehci [ 9.844333] rtc-mv f1010300.rtc: internal RTC not ticking [ 9.849924] i2c /dev entries driver [ 9.854784] hidraw: raw HID events driver (C) Jiri Kosina [ 9.860568] drop_monitor: Initializing network drop monitor service [ 9.867269] NET: Registered protocol family 17 [ 9.871868] Key type dns_resolver registered [ 9.877024] usb 1-1.1: New USB device found, idVendor=8644, idProduct=8003 [ 9.883953] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 9.891557] registered taskstats version 1 [ 9.891561] Loading compiled-in X.509 certificates [ 9.891616] zswap: loaded using pool lzo/zbud [ 9.906104] Key type big_key registered [ 9.928910] usb 1-1.1: Product: USB Flash Disk [ 9.934980] Key type encrypted registered [ 9.940028] usb 1-1.1: Manufacturer: General [ 9.946394] usb 1-1.1: SerialNumber: 0663000000008F3F [ 9.952248] hctosys: unable to open rtc device (rtc0) [ 9.957619] usb-storage 1-1.1:1.0: USB Mass Storage device detected [ 9.964527] scsi host0: usb-storage 1-1.1:1.0 [ 9.972680] Freeing unused kernel memory: 1024K Loading, please wait... starting version 232 [ 10.375832] usbcore: registered new interface driver uas Begin: Loading essential drivers ... done. [ 11.045592] scsi 0:0:0:0: Direct-Access General USB Flash Disk 1.00 PQ: 0 ANSI: 2 [ 11.059423] sd 0:0:0:0: [sda] 7831552 512-byte logical blocks: (4.01 GB/3.73 GiB) [ 11.073056] sd 0:0:0:0: [sda] Write Protect is off [ 11.084802] sd 0:0:0:0: [sda] No Caching mode page found [ 11.090150] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 11.108398] sda: sda1 [ 11.117168] sd 0:0:0:0: [sda] Attached SCSI removable disk Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Warning: fsck not present, so skipping root file system [ 20.733572] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 20.751852] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [ ok ] Setting hostname to 'debian'...done. [....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232 . ok [ ok ] Synthesizing the initial hotplug events...done. [....] Waiting for /dev to be fully populated...[ 23.115632] orion_wdt: Initial timeout 21 sec [ 23.216154] marvell-cesa f1030000.crypto: CESA device successfully registered [ 23.307092] sd 0:0:0:0: Attached scsi generic sg0 type 0 done. [ ok ] Activating swap:. [ 24.336085] EXT4-fs (sda1): re-mounted. Opts: (null) [....] Will now check root file system:fsck from util-linux 2.29.2 [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sda1 e2fsck 1.43.4 (31-Jan-2017) rootfs: clean, 14456/244800 files, 202054/978688 blocks . ok [ 24.624098] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ ok ] Will now activate lvm and md swap:done. [info] Will now check all file systems. fsck from util-linux 2.29.2 Checking all file systems. LABEL=rootfs is mounted [ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. [ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done. [ ok . [ 26.064412] random: crng init done [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables...done. [ ok ] Initializing random number generator...done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5 Copyright 2004-2016 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:25:31:04:80:8c Sending on LPF/eth0/00:25:31:04:80:8c Sending on Socket/fallback DHCPREQUEST of 192.168.0.14 on eth0 to 255.255.255.255 port 67 [ 30.927742] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 37.344629] NET: Registered protocol family 10 [ 37.353340] Segment Routing with IPv6 DHCPREQUEST of 192.168.0.14 on eth0 to 255.255.255.255 port 67 DHCPNAK from 192.168.222.1 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4 DHCPREQUEST of 192.168.222.168 on eth0 to 255.255.255.255 port 67 DHCPOFFER of 192.168.222.168 from 192.168.222.1 DHCPACK of 192.168.222.168 from 192.168.222.1 bound to 192.168.222.168 -- renewal in 41465 seconds. done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1328 (syslogd) . ok [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1326 (klogd) . ok [ ok ] Running local boot scripts (/etc/rc.local). Debian GNU/Linux 9 debian ttyS0 debian login: root Password: Last login: Wed Dec 31 16:01:32 PST 1969 from 192.168.0.220 on pts/0 Linux debian 4.12.1-kirkwood-tld-1 #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 armv5tel The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@debian:~# root@debian:~# root@debian:~# mount sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,relatime) proc on /proc type proc (rw,nosuid,nodev,noexec,relatime) udev on /dev type devtmpfs (rw,nosuid,relatime,size=119688k,nr_inodes=29922,mode=755) devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000) tmpfs on /run type tmpfs (rw,nosuid,noexec,relatime,size=24748k,mode=755) /dev/sda1 on / type ext3 (rw,noatime,errors=remount-ro,data=ordered) tmpfs on /run/lock type tmpfs (rw,nosuid,nodev,noexec,relatime,size=5120k) tmpfs on /run/shm type tmpfs (rw,nosuid,nodev,noexec,relatime,size=49480k) tmpfs on /tmp type tmpfs (rw,relatime) rpc_pipefs on /run/rpc_pipefs type rpc_pipefs (rw,relatime) root@debian:~# root@debian:~# root@debian:~# uname -a Linux debian 4.12.1-kirkwood-tld-1 #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 armv5tel GNU/Linux root@debian:~# root@debian:~# root@debian:~# cat /boot/uEnv.txt dtb_file=/boot/dts/kirkwood-pogo_e02.dtb devices=usb devices=usb disks=0 1 2 3 4 5 6 7
Re: Pogoplug E02 Debian Linux Installation Guide October 23, 2017 01:58AM |
Registered: 8 years ago Posts: 88 |
> uname -a > dpkg -l | grep linux-image > ls -lart /lib/modules/ -d > cat /proc/mtd > dmesg | grep -i bad > mount >>
> cat /etc/fw_env.config > fw_printenv >>
> ls -latr /boot > ls -latr /boot/dts/kirkwood-*pogo* >
root@debian:/# root@debian:/# root@debian:/# uname -a Linux debian 4.12.1-kirkwood-tld-1 #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 armv5tel GNU/Linux root@debian:/# root@debian:/# dpkg -l | grep linux-image ii linux-image-4.12.1-kirkwood-tld-1 1.0 armel Linux kernel binary image for version 4.12.1-kirkwood-tld-1 root@debian:/# root@debian:/# root@debian:/# ls -lart /lib/modules/ -d drwxr-xr-x 3 root root 4096 Dec 31 1969 /lib/modules/ root@debian:/# root@debian:/# root@debian:/# cat /proc/mtd dev: size erasesize name mtd0: 00100000 00020000 "u-boot" mtd1: 00400000 00020000 "uImage" mtd2: 02000000 00020000 "rootfs" mtd3: 05b00000 00020000 "data" root@debian:/# root@debian:/# root@debian:/# dmesg | grep -i bad [ 7.438411] Scanning device for bad blocks root@debian:/# root@debian:/# root@debian:/# root@debian:/# mount sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,relatime) proc on /proc type proc (rw,nosuid,nodev,noexec,relatime) udev on /dev type devtmpfs (rw,nosuid,relatime,size=119688k,nr_inodes=29922,mode=755) devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000) tmpfs on /run type tmpfs (rw,nosuid,noexec,relatime,size=24748k,mode=755) /dev/sda1 on / type ext3 (rw,noatime,errors=remount-ro,data=ordered) tmpfs on /run/lock type tmpfs (rw,nosuid,nodev,noexec,relatime,size=5120k) tmpfs on /run/shm type tmpfs (rw,nosuid,nodev,noexec,relatime,size=49480k) tmpfs on /tmp type tmpfs (rw,relatime) rpc_pipefs on /run/rpc_pipefs type rpc_pipefs (rw,relatime) root@debian:/# root@debian:/# root@debian:/# root@debian:/# root@debian:/# cat /etc/fw_env.config # MTD device name Device offset Env. size Flash sector size Number of sectors /dev/mtd0 0xc0000 0x20000 0x20000 root@debian:/# root@debian:/# root@debian:/# ls -latr /boot total 36264 drwxr-xr-x 21 root root 4096 Feb 16 2015 .. -rw-r--r-- 1 root root 153501 Jul 15 20:21 config-4.12.1-kirkwood-tld-1 -rwxr-xr-x 1 root root 3821528 Jul 15 21:42 zImage-4.12.1-kirkwood-tld-1 -rw------- 1 root root 3821528 Jul 16 00:43 vmlinuz-4.12.1-kirkwood-tld-1 -rw------- 1 root root 2504031 Jul 16 00:43 System.map-4.12.1-kirkwood-tld-1 -rw-r--r-- 1 root root 8435004 Jul 16 01:06 linux-headers-4.12.1-kirkwood-tld-1_1.0_armel.deb -rw-r--r-- 1 root root 3821592 Jul 20 01:11 uImage -rw-r--r-- 1 root root 7245632 Jul 23 17:15 initrd.img-4.12.1-kirkwood-tld-1 -rw-r--r-- 1 root root 7245696 Jul 23 17:18 uInitrd -rw-r--r-- 1 root root 88 Oct 22 00:43 uEnv.txt drwxr-xr-x 3 root root 4096 Oct 22 00:43 . drwxr-xr-x 3 root root 4096 Oct 22 01:40 dts root@debian:/# root@debian:/# root@debian:/# root@debian:/# ls -latr /boot/dts/kirkwood-*pogo* -rw-r--r-- 1 root root 10284 Jul 16 01:08 /boot/dts/kirkwood-pogoplug_v4.dtb -rw-r--r-- 1 root root 10444 Jul 16 01:08 /boot/dts/kirkwood-pogo_e02.dtb root@debian:/# root@debian:/#
Re: Pogoplug E02 Debian Linux Installation Guide October 23, 2017 02:34AM |
Admin Registered: 13 years ago Posts: 18,575 |
root@debian:~# root@debian:~# root@debian:~# fw_printenv bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 ethact=egiga0 if_netconsole=ping $serverip led_error=orange blinking led_exit=green off led_init=green blinking dtb_file=/boot/dts/kirkwood-pogo_e02.dtb load_dtb_addr=0x1c00000 load_initrd_addr=0x1100000 load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi usb_ready_retry=15 arcNumber=3542 machid=dd6 ethaddr=00:25:31:04:80:8C disks=0 1 2 3 4 5 6 7 preboot_nc=setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi preboot=run preboot_nc ipaddr=192.168.222.168 devices=usb load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage serverip=192.168.222.164 root@debian:~# root@debian:~#
dtb_file=/boot/dts/kirkwood-pogo_e02.dtb devices=usb devices=usb disks=0 1 2 3 4 5 6 7
fw_setenv prebootWhen you want to turn on netconsole (i.e. removing serial console for other duty), you can turn it back on:
fw_setenv preboot 'run preboot_nc'
Re: Pogoplug E02 Debian Linux Installation Guide October 23, 2017 03:16AM |
Registered: 8 years ago Posts: 88 |
Note2: To boot with systemd, add parameter init=/bin/systemd to your u-boot env bootargs. - For example, fw_setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts init=/bin/systemd' - Or, if you are booting with my latest u-boot images you can also use the uEnv.txt capability to do this. In the default envs, custom_params is a variable that allows you to add extra bootargs. So add the following line to uEnv.txt: custom_params=init=/bin/systemd If that's still not possible to run systemd, you might want to install it again: apt-get install systemd
Re: Pogoplug E02 Debian Linux Installation Guide October 23, 2017 03:30AM |
Registered: 8 years ago Posts: 88 |
> fw_setenv preboot >> When you want to turn on netconsole (i.e. removing
> fw_setenv preboot 'run preboot_nc' >>
Re: Pogoplug E02 Debian Linux Installation Guide October 23, 2017 02:14PM |
Registered: 8 years ago Posts: 88 |
PogoE02> PogoE02> boot starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 60 second(s) 1 Storage Device(s) found Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 7829504 3fd1c278-01 83 Boot loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 253 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 3848064 bytes read in 411 ms (8.9 MiB/s) loading uInitrd ... EHCI timed out on TD - token=0xa0008d80 EHCI timed out on TD - token=0x128d80 EHCI timed out on TD - token=0x20008d80 EHCI timed out on TD - token=0x128d80 EHCI timed out on TD - token=0x20008d80 EHCI timed out on TD - token=0x128d80 ** ext4fs_devread read error - block loading DTB /boot/dts/kirkwood-pogo_e02.dtb ... EHCI timed out on TD - token=0x2008d80 EHCI timed out on TD - token=0x128d80 EHCI timed out on TD - token=0x2008d80 EHCI timed out on TD - token=0x128d80 EHCI timed out on TD - token=0x2008d80 EHCI timed out on TD - token=0x128d80 ** Can't read partition table on 0:0 ** ** Invalid partition 1 ** ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.13.5-kirkwood-tld-1 Created: 2017-10-23 12:01:29 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3848000 Bytes = 3.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK Using machid 0xdd6 from environment Starting kernel ... Uncompressing Linux... done, booting the kernel. Error: unrecognized/unsupported machine ID (r1 = 0x00000dd6). Available machine support: ID (hex) NAME ffffffff Generic DT based system ffffffff Marvell Kirkwood (Flattened Device Tree) Please check your kernel config and/or bootloader.
PogoE02> PogoE02> printenv arcNumber=3542 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb disks=0 1 2 3 4 5 6 7 dtb_file=/boot/dts/kirkwood-pogo_e02.dtb ethact=egiga0 ethaddr=00:25:31:04:80:8C if_netconsole=ping $serverip ipaddr=192.168.222.168 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 machid=dd6 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 preboot_nc=setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.222.140 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15 Environment size: 2997/131068 bytes PogoE02>
Re: Pogoplug E02 Debian Linux Installation Guide October 23, 2017 02:40PM |
Admin Registered: 13 years ago Posts: 18,575 |
Re: Pogoplug E02 Debian Linux Installation Guide August 29, 2018 06:15PM |
Registered: 5 years ago Posts: 2 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700) Pogo E02 SoC: Kirkwood 88F6281_A0 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 PogoE02> version U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700) Pogo E02 gcc (Debian 6.3.0-18) 6.3.0 20170516 GNU ld (GNU Binutils for Debian) 2.28 PogoE02>
Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 14422016 683440f4-01 83 2 14424064 1017856 683440f4-02 82 Attempting to boot from usb 0:1... ** File not found /boot/uEnv.txt ** Checking if uenvcmd is set ... Running default loadzimage ... ** File not found /boot/zImage ** Running default loaduimage ... 2840564 bytes read in 508 ms (5.3 MiB/s) Booting from 0 ... ## Booting kernel from Legacy Image at 00810000 ... Image Name: Linux-2.6.33 Created: 2010-03-02 21:27:23 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2840500 Bytes = 2.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel.
PogoE02> printenv arcNumber=2097 autoload=no baudrate=115200 bootcmd=usb start; setenv letter 9;for type in usb; do for disk in 0 1 2 3; do if ${type} part ${disk};then setexpr letter $letter + 1;run load;fi;done;done; bootdelay=3 bootm=echo Booting from ${disk} ...; run setargs; bootm ${loadaddr}; bootz=echo Booting from ${disk} ...; run setargs; bootz ${loadaddr} - ${fdt_addr}; console=ttyS0 dnsip=192.168.42.1 ethact=egiga0 ethaddr=00:25:31:02:C6:10 fdt_addr=0x800000 fdt_file=/boot/dts/kirkwood-pogo_e02.dtb gatewayip=192.168.42.1 importbootenv=echo Importing environment (uEnv.txt)...; env import -t $loadaddr $filesize ipaddr=192.168.42.35 letter=d load=echo Attempting to boot from ${type} ${disk}:1...;if run loadbootenv; then run importbootenv;fi;echo Checking if uenvcmd is set ...;if test -n $uenvcmd; then echo Running uenvcmd ...;run uenvcmd;fi;echo Running default loadzimage ...;if run loadzimage; then run loadfdt;run bootz;fi;echo Running default loaduimage ...;if run loaduimage; then run bootm;fi; load_dtb=ext2load usb 0:1 0x1c00000 /boot/dts/kirkwood-pogo_e02.dtb loadaddr=0x810000 loadbootenv=load ${type} ${disk}:1 ${loadaddr} /boot/uEnv.txt loadfdt=load ${type} ${disk}:1 ${fdt_addr} ${fdt_file} loaduimage=load ${type} ${disk}:1 ${loadaddr} ${uimage} loadzimage=load ${type} ${disk}:1 ${loadaddr} ${zimage} matchid=dd6 mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),-(rootfs) netmask=255.255.255.0 setargs=setenv bootargs console=${console},${baudrate} ${optargs} root=/dev/sd${letter}1 rw rootwait ${mtdparts} stderr=serial stdin=serial stdout=serial uimage=/boot/uImage zimage=/boot/zImage Environment size: 1688/131068 bytes mtdparts device nand0 <orion_nand>, # parts = 2 #: name size offset mask_flags 0: u-boot 0x00100000 0x00000000 0 1: rootfs 0x07f00000 0x00100000 0 active partition: nand0,0 - (u-boot) 0x00100000 @ 0x00000000 defaults: mtdids : none mtdparts: none PogoE02>
Re: Pogoplug E02 Debian Linux Installation Guide August 29, 2018 07:30PM |
Admin Registered: 13 years ago Posts: 18,575 |
Quote
On another Linux box, mount the Debian rootfs that you meant to run on this box and put the attached u-boot script in the /boot folder (if it was mounted at /media/sdb1):
cp -a uboot.2016.05-tld-1.environment.scr /media/sdb1/boot/
Power up this box and interrupt serial console, run the script loading commands:
usb start
ext2load usb 0:1 0x800000 /boot/uboot.2016.05-tld-1.environment.scr
source 0x800000
printenv
Verify that the default envs look good as the source uboot.2016.05-tld-1.environment (which you've already downloaded).
Adjust the other specific envs and then boot the rootfs:
setenv devices 'usb'
setenv ethaddr xx:xx:xx:xx:xx:xx
setenv dtb_file '/boot/dts/kirkwood-pogo_e02.dtb'
boot
Quote
8. Flashing default u-boot envs image (if you are upgrading from 2016.05-tld-1 u-boot, you can skip this step 8).
As described in step 1, u-boot envs must be defined in /etc/fw_env.config as
# MTD device name Device offset Env. size Flash sector size Number of sectors
/dev/mtd0 0xc0000 0x20000 0x20000
Re: Pogoplug E02 Debian Linux Installation Guide August 30, 2018 03:58PM |
Registered: 5 years ago Posts: 2 |
Re: Pogoplug E02 Debian Linux Installation Guide August 30, 2018 05:18PM |
Admin Registered: 13 years ago Posts: 18,575 |