|
Debian on Verbatim MediaShare Mini September 06, 2016 12:49AM |
Registered: 9 years ago Posts: 442 |
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: DB-88F6281A-BP LE
The board type is Topkick0281
U-Boot 1.1.4 (Jul 13 2010 - 12:04:50) Marvell version: 3.4.27
USISH-SMB Ver: topkick0281-20100706-axentra
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006D0120
Soc: 88F6281 A1 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> printenv^M
baudrate=115200
loads_echo=0
ipaddr=192.168.58.21
serverip=192.168.58.135
rootpath=/mnt/ARM_FS/
netmask=255.255.255.0
run_diag=yes
CASset=min
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
nandEcc=1bit
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
ethact=egiga0
bootargs=console=ttyS0,115200;version=topkick0281-002-001-20100701-verbatim
initializeKernelRamdisk=run initializeUSB; nand erase clean 0x200000 0x600000; nand write.e 0x1200000 0x200000 0x300000; nand erase clean 0x800000 0x1000000; nand write.e 0x1800000 0x800000 0x800000
filesize=61123C
ethaddr=00:27:13:ff:f1:f3
PK=VPRQ-FPTA-NWKT-QWWR
console=console=ttyS0,115200
initializeDev=run initializeKernel; setenv bootargs console=ttyS0,115200 root=/dev/ram0 rw ramdisk=0x01100000,8M install_type=nand; bootm 0x00800000 0x01100000
initializeKernel=run initializeUSB; nand erase clean 0x00200000 0x00600000; nand write.e 0x00800000 0x00200000 0x00600000
initializeUSB=usb start; fatload usb 0 0x00800000 uImage; fatload usb 0 0x01100000 initrd
save_crc=true
install_mode=false
bootargs_root=ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc
console2=console=ttyS0,115200
bootcmd=nand read.e 0x800000 0x200000 0x600000; setenv bootargs $(console2) $(bootargs_root); bootm 0x800000
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
Environment size: 1920/131068 bytes
Marvell>> help^M
? - alias for 'help'
SatR - sample at reset sub-system, relevent for DB only
base - print or set address offset
boot - boot default, i.e., run 'bootcmd'
bootd - boot default, i.e., run 'bootcmd'
bootext2 dev:boot_part1,boot_part2 addr boot_image linux_dev_name
bootm - boot application image from memory
bootp - boot image via network using BootP/TFTP protocol
bubt - Burn an image on the Boot Nand Flash.
chpart - change active partition
cmp - memory compare
cmpm - Compare Memory
cp - memory copy
cpumap - Display CPU memory mapping settings.
crc32 - checksum calculation
date - get/set/reset date & time
dclk - Display the MV device CLKs.
dhcp - invoke DHCP client to obtain IP/boot params
diskboot- boot from IDE device
echo - echo args to console
eeprom - EEPROM sub-system
erase - erase FLASH memory
ext2load- load binary file from a Ext2 filesystem
ext2ls - list files in a directory (default /)
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
fi - Find value in the memory.
flinfo - print FLASH memory information
fsinfo - print information about filesystems
fsload - load binary file from a filesystem image
g - start application at cached address 'addr'(default addr 0x40000)
go - start application at address 'addr'
help - print online help
icrc32 - checksum calculation
ide - IDE sub-system
iloop - infinite loop on address range
imd - i2c memory display
iminfo - print header information for application image
imm[.b, .s, .w, .l] - i2c memory modify (auto-incrementing)
imw - memory write (fill)
inm - memory modify (constant address)
iprobe - probe to discover valid I2C chip addresses
ir - reading and changing MV internal register values.
loop - infinite loop on address range
ls - list files in a directory (default /)
map - Diasplay address decode windows
md - memory display
me - PCI master enable
mm - memory modify (auto-incrementing)
mmcinit - init mmc card
mp - map PCI BAR
mtdparts- define flash/nand partitions
mtest - simple RAM test
mw - memory write (fill)
nand - NAND sub-system
nboot - boot from NAND device
nbubt - Burn a boot loader image on the Boot Nand Flash.
nm - memory modify (constant address)
pci - list and access PCI Configuration Space
phyRead - Read PCI-E Phy register
pciePhyWrite - Write PCI-E Phy register
phyRead - Read Phy register
phyWrite - Write Phy register
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
rcvr - Satrt recovery process (Distress Beacon with TFTP server)
reset - Perform RESET of the CPU
resetenv - Return all environment variable to default.
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
se - PCI Slave enable
setenv - set environment variables
sflash - read, write or erase the external SPI Flash.
sg - scanning the PHYs status
sp - Scan PCI bus.
switchRegRead - Read switch register
switchRegWrite - Write switch register
tftpboot- boot image via network using TFTP protocol
usb - USB sub-system
usbboot - boot from USB device
version - print monitor version
Marvell>>
|
Re: Debian on Verbatim MediaShare Mini September 06, 2016 01:40AM |
Admin Registered: 13 years ago Posts: 18,564 |
ETH chip1: Marvell 88F6281 ETH chip2: Marvell 88E1116R LAN speed: 10/100/1000 LAN ports: 1
|
Re: Debian on Verbatim MediaShare Mini September 06, 2016 01:47AM |
Admin Registered: 13 years ago Posts: 18,564 |
|
Re: Debian on Verbatim MediaShare Mini September 06, 2016 01:58AM |
Admin Registered: 13 years ago Posts: 18,564 |
|
Re: Debian on Verbatim MediaShare Mini September 06, 2016 02:21AM |
Registered: 9 years ago Posts: 442 |
> ETH chip1: Marvell 88F6281 > ETH chip2: Marvell 88E1116R > LAN speed: 10/100/1000 > LAN ports: 1 >>
|
Re: Debian on Verbatim MediaShare Mini September 06, 2016 02:33AM |
Admin Registered: 13 years ago Posts: 18,564 |
|
Re: Debian on Verbatim MediaShare Mini September 06, 2016 02:35AM |
Registered: 9 years ago Posts: 442 |
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: DB-88F6281A-BP LE
The board type is Topkick0281
U-Boot 1.1.4 (Jul 13 2010 - 12:04:50) Marvell version: 3.4.27
USISH-SMB Ver: topkick0281-20100706-axentra
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006D0120
Soc: 88F6281 A1 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x200000, size 0x600000
^MReading data from 0x200000 -- 0% complete.^MReading data from 0x20f000 -- 1% complete.^MReading data from 0x21e800 -- 2% complete.^MReading data from 0x22e000 -- 3% complete.^MReading data from 0x23d000 -- 4% complete.^M^MReading data from 0x24c800 -- 5% complete.^MReading data from 0x25c000 -- 6% complete.^MReading data from 0x26b800 -- 7% complete.^MReading data from 0x27a800 -- 8% complete.^MReading data from 0x28a000 -- 9% complete.^M^MReading data from 0x299800 -- 10% complete.^MReading data from 0x2a8800 -- 11% complete.^MReading data from 0x2b8000 -- 12% complete.^MReading data from 0x2c7800 -- 13% complete.^MReading data from 0x2d7000 -- 14% complete.^M^MReading data from 0x2e6000 -- 15% complete.^MReading data from 0x2f5800 -- 16% complete.^MReading data from 0x305000 -- 17% complete.^MReading data from 0x314000 -- 18% complete.^MReading data from 0x323800 -- 19% complete.^M^MReading data from 0x333000 -- 20% complete.^MReading data from 0x342800 -- 21% complete.^MReading data from 0x351800 -- 22% complete.^MReading data from 0x361000 -- 23% complete.^MReading data from 0x370800 -- 24% complete.^M^MReading data from 0x37f800 -- 25% complete.^MReading data from 0x38f000 -- 26% complete.^MReading data from 0x39e800 -- 27% complete.^MReading data from 0x3ae000 -- 28% complete.^MReading data from 0x3bd000 -- 29% complete.^M^MReading data from 0x3cc800 -- 30% complete.^MReading data from 0x3dc000 -- 31% complete.^MReading data from 0x3eb800 -- 32% complete.^MReading data from 0x3fa800 -- 33% complete.^MReading data from 0x40a000 -- 34% complete.^M^MReading data from 0x419800 -- 35% complete.^MReading data from 0x428800 -- 36% complete.^MReading data from 0x438000 -- 37% complete.^MReading data from 0x447800 -- 38% complete.^MReading data from 0x457000 -- 39% complete.^M^MReading data from 0x466000 -- 40% complete.^MReading data from 0x475800 -- 41% complete.^MReading data from 0x485000 -- 42% complete.^MReading data from 0x494000 -- 43% complete.^MReading data from 0x4a3800 -- 44% complete.^M^MReading data from 0x4b3000 -- 45% complete.^MReading data from 0x4c2800 -- 46% complete.^MReading data from 0x4d1800 -- 47% complete.^MReading data from 0x4e1000 -- 48% complete.^MReading data from 0x4f0800 -- 49% complete.^M^MReading data from 0x4ff800 -- 50% complete.^MReading data from 0x50f000 -- 51% complete.^MReading data from 0x51e800 -- 52% complete.^MReading data from 0x52e000 -- 53% complete.^MReading data from 0x53d000 -- 54% complete.^M^MReading data from 0x54c800 -- 55% complete.^MReading data from 0x55c000 -- 56% complete.^MReading data from 0x56b800 -- 57% complete.^MReading data from 0x57a800 -- 58% complete.^MReading data from 0x58a000 -- 59% complete.^M^MReading data from 0x599800 -- 60% complete.^MReading data from 0x5a8800 -- 61% complete.^MReading data from 0x5b8000 -- 62% complete.^MReading data from 0x5c7800 -- 63% complete.^MReading data from 0x5d7000 -- 64% complete.^M^MReading data from 0x5e6000 -- 65% complete.^MReading data from 0x5f5800 -- 66% complete.^MReading data from 0x605000 -- 67% complete.^MReading data from 0x614000 -- 68% complete.^MReading data from 0x623800 -- 69% complete.^M^MReading data from 0x633000 -- 70% complete.^MReading data from 0x642800 -- 71% complete.^MReading data from 0x651800 -- 72% complete.^MReading data from 0x661000 -- 73% complete.^MReading data from 0x670800 -- 74% complete.^M^MReading data from 0x67f800 -- 75% complete.^MReading data from 0x68f000 -- 76% complete.^MReading data from 0x69e800 -- 77% complete.^MReading data from 0x6ae000 -- 78% complete.^MReading data from 0x6bd000 -- 79% complete.^M^MReading data from 0x6cc800 -- 80% complete.^MReading data from 0x6dc000 -- 81% complete.^MReading data from 0x6eb800 -- 82% complete.^MReading data from 0x6fa800 -- 83% complete.^MReading data from 0x70a000 -- 84% complete.^M^MReading data from 0x719800 -- 85% complete.^MReading data from 0x728800 -- 86% complete.^MReading data from 0x738000 -- 87% complete.^MReading data from 0x747800 -- 88% complete.^MReading data from 0x757000 -- 89% complete.^M^MReading data from 0x766000 -- 90% complete.^MReading data from 0x775800 -- 91% complete.^MReading data from 0x785000 -- 92% complete.^MReading data from 0x794000 -- 93% complete.^MReading data from 0x7a3800 -- 94% complete.^M^MReading data from 0x7b3000 -- 95% complete.^MReading data from 0x7c2800 -- 96% complete.^MReading data from 0x7d1800 -- 97% complete.^MReading data from 0x7e1000 -- 98% complete.^MReading data from 0x7f0800 -- 99% complete.^M^MReading data from 0x7ff800 -- 100% complete.
6291456 bytes read: OK
## Booting image at 00800000 ...
Image Name: Linux-2.6.22.18
Created: 2010-07-16 14:28:07 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1657568 Bytes = 1.6 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux.................................................................................................
......... done, booting the kernel.
^MLinux version 2.6.22.18 (khaled@es5x86.axentra.com) (gcc version 4.3.2 (sdk3.2rc1-ct-ng-1.4.1) ) #1 Fri Jul 16 10:
28:00 EDT 2010
CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053977
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists. Total pages: 65024
Kernel command line: console=ttyS0,115200 ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB 0MB 0MB 0MB = 256MB total
Memory: 256384KB available (3060K code, 221K data, 108K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 256MB
SDRAM_CS1 ....base 10000000, size 256MB
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e8000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
INTER_REGS ....base f1000000, size 1MB
NFLASH_CS ....base fa000000, size 2MB
SPI_CS ....base f4000000, size 16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size 2MB
Marvell Development Board (LSP Version kernel-2.6.22-topkick-1.0.0.2)-- USI-88F6281A Soc: 88F6281 A1 LE
Detected Tclk 166666667 and SysClk 200000000
MV Buttons Device Load
Marvell USB EHCI Host controller #0: c05c0600
PEX0 interface detected no Link.
PCI: bus0: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
Time: kw_clocksource clocksource has been installed.
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
RTC registered
Use the XOR engines (acceleration) for enhancing the following functions:
o RAID 5 Xor calculation
o kernel memcpy
o kenrel memzero
Number of XOR engines to use: 4
cesadev_init(c0010ddc)
mvCesaInit: sessions=640, queue=64, pSram=f0000000
MV Buttons Driver Load
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
Loading Marvell Ethernet Driver:
o Cached descriptors in DRAM
o DRAM SW cache-coherency
o Single RX Queue support - ETH_DEF_RXQ=0
o Single TX Queue support - ETH_DEF_TXQ=0
o TCP segmentation offload enabled
o Receive checksum offload enabled
o Transmit checksum offload enabled
o Network Fast Processing (Routing) supported
o Driver ERROR statistics enabled
o Driver INFO statistics enabled
o Proc tool API enabled
o Rx descripors: q0=128
o Tx descripors: q0=532
o Loading network interface(s):
o eth0, ifindex = 1, GbE port = 0
Warning: Giga 1 is Powered Off
mvFpRuleDb (cfd14000): 2048 entries, 8192 bytes
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
Copyright (c) 1999-2006 Intel Corporation.
e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Using static partition definition
Creating 3 MTD partitions on "nand_mtd":
0x00000000-0x00200000 : "u-boot"
0x00200000-0x00800000 : "uImage"
0x00800000-0x10000000 : "root"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: attached mtd2 to ubi0
UBI: MTD device name: "root"
UBI: MTD device size: 248 MiB
UBI: number of good PEBs: 1984
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 1984
UBI: number of PEBs reserved for bad PEB handling: 38
UBI: max/mean erase counter: 1/0
UBI: background thread "ubi_bgt0d" started, PID 316
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v3.0
usb 1-1: new high speed USB device using ehci_marvell and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usish: set gpio39 to 1
usb 1-1.4: new high speed USB device using ehci_marvell and address 3
usb 1-1.4: configuration #1 chosen from 1 choice
usish: set gpio39 to 1
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
pwrctl: dev_t_NO. = 0xdd00000, major = 221
pwrctl: HDD1(0),HDD2(0)
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size: 239857664 bytes (234236 KiB, 228 MiB, 1889 LEBs)
UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format: 4 (latest is 4)
UBIFS: default compressor: zlib
UBIFS: reserved for root: 0 bytes (0 KiB)
VFS: Mounted root (ubifs filesystem).
Freeing init memory: 108K
Failed to execute /linuxrc. Attempting defaults...
^MINIT: version 2.86 booting^M
Welcome to HipServ
Press 'I' to enter interactive startup.
Setting clock (utc): Tue Sep 6 03:27:33 EDT 2016 [ OK ]^M
Starting udev: [ OK ]^M
Setting hostname axentraserver.mediashareminirk.myverbatim.com: [ OK ]^M
Checking filesystems
Checking all file systems.
[ OK ]^M
Mounting local filesystems: mount: sysfs already mounted or /sys busy
mount: according to mtab, /sys is already mounted on /sys
[FAILED]^M
Enabling /etc/fstab swaps: [ OK ]
^MINIT: Entering runlevel: 3^M
Entering non-interactive startup
HipServ startup:[ OK ]^M
Starting reset: [ OK ]^M
Bringing up loopback interface: [ OK ]^M
Bringing up interface eth0:
Determining IP information for eth0... done.
/etc/init.d/iptables: line 42: /etc/sysconfig/networking/oe-profiles/default/ifcfg-eth0: No such file or directory
Flushing all current rules and user defined chains: [ OK ]^M
Clearing all current rules and user defined chains: [ OK ]^M
[ OK ]^M[ OK ]^MApplying iptables firewall rules:
[ OK ]^M
[ OK ]^M
Starting system logger: [ OK ]^M
Starting kernel logger: [ OK ]^M
Starting locator:[ OK ]^M
Starting system message bus: [ OK ]^M
Starting sshd: [ OK ]^M
Starting cups: [ OK ]^M
Starting xinetd: [ OK ]^M
Starting vsftpd for vsftpd: [ OK ]^M
Starting access-patrol:[ OK ]^M
Starting httpd: [ OK ]^M
Starting appserver: [ OK ]^M
Starting crond: [ OK ]^M
Starting SMB services: [ OK ]^M
Starting NMB services: [ OK ]^M
check_igd.pl: no process killed
Starting igd-daemon:[ OK ]^M[ OK ]^M
Starting OEone System Proxy: SPD starting....log level=1, uid=0
[ OK ]^M
Starting Avahi daemon... [ OK ]^M
Starting twonky: Starting /usr/local/TwonkyVision/twonkymedia ... Daemonizing...
[ OK ]^M
Starting DAAP server: [ OK ]^M
Starting mynetworkd:[ OK ]^M
HipServ - Checking if RAID needs to be rebuilt
HipServ - No RAID found
HipServ - Bringing up iptables
HipServ - Updating date...
[ OK ]^M success
HipServ - Checking for updates...
[ OK ]^M success
HipServ - Enabling swap
HipServ - Cleaning USB mountpoints
HipServ - Mounting USB devices
ufsd: module license 'Commercial product' taints kernel.
ufsd: driver 8.1 (022_A) LBD=ON with ioctl loaded at bf04f000
NTFS read/write support included
Hfs+/HfsX read/write support included
Unknown HZ value! (88) Assume 100.
Unknown HZ value! (88) Assume 100.
Unknown HZ value! (88) Assume 100.
Unknown HZ value! (88) Assume 100.
HipServ - Checking for FTPS certificate
HipServ - Found vsftpd key file
HipServ - Starting usbreaderd: [ OK ]
HipServ - boot complete
axentraserver.mediashareminirk.myverbatim.com login:
|
Re: Debian on Verbatim MediaShare Mini September 06, 2016 02:49AM |
Admin Registered: 13 years ago Posts: 18,564 |
|
Re: Debian on Verbatim MediaShare Mini September 06, 2016 11:24PM |
Registered: 9 years ago Posts: 442 |
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: DB-88F6281A-BP LE
The board type is Topkick0281
U-Boot 1.1.4 (Jul 13 2010 - 12:04:50) Marvell version: 3.4.27
USISH-SMB Ver: topkick0281-20100706-axentra
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006D0120
Soc: 88F6281 A1 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10^M
Marvell>> usb start^M
(Re)start USB...
USB: scanning bus for devices... 3 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
Marvell>> ext2load usb 0:1 0x800000 /boot/uImage^M
....
.
......
............
.........................
...................................................
......................................................................................................
........................................................................................................
3165294 bytes read
Marvell>> ext2load usb 0:1 0x1100000 /boot/uInitrd^M
....
.
......
............
.........................
...................................................
......................................................................................................
.................................................................................................................................................................................................................
..............................................................................................................................................................................................................................................................................................
7179935 bytes read
Marvell>> bootm 0x800000 0x1100000^M
## Booting image at 00800000 ...
Image Name: Linux-4.4.0-kirkwood-tld-1
Created: 2016-09-07 3:59:49 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3165230 Bytes = 3 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
Image Name: initramfs-4.4.0-kirkwood-tld-1
Created: 2016-02-19 7:33:04 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 7179871 Bytes = 6.8 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine model: Seagate FreeAgent Dockstar
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 243580K/262144K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 18564K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc07d7ef4 (8000 kB)
[ 0.000000] .init : 0xc07d8000 - 0xc0822000 ( 296 kB)
[ 0.000000] .data : 0xc0822000 - 0xc08b169c ( 574 kB)
[ 0.000000] .bss : 0xc08b169c - 0xc08ff9d0 ( 313 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[ 0.000016] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[ 0.000529] Console: colour dummy device 80x30
[ 0.000582] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216)
[ 0.090145] pid_max: default: 32768 minimum: 301
[ 0.090329] Security Framework initialized
[ 0.090454] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090488] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.091841] Initializing cgroup subsys io
[ 0.091901] Initializing cgroup subsys devices
[ 0.091942] Initializing cgroup subsys freezer
[ 0.092001] Initializing cgroup subsys net_cls
[ 0.092148] CPU: Testing write buffer coherency: ok
[ 0.092941] Setting up static identity map for 0x8200 - 0x8258
[ 0.093424] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[ 0.099554] devtmpfs: initialized
[ 0.107347] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.108151] prandom: seed boundary self test passed
[ 0.113850] prandom: 100 self tests passed
[ 0.113912] pinctrl core: initialized pinctrl subsystem
[ 0.116298] NET: Registered protocol family 16
[ 0.117011] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.140186] cpuidle: using governor ladder
[ 0.170181] cpuidle: using governor menu
[ 0.170813] Feroceon L2: Enabling L2
[ 0.170882] Feroceon L2: Cache support initialised.
[ 0.171465] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[ 0.178698] No ATAGs?
[ 0.212447] vgaarb: loaded
[ 0.213020] usbcore: registered new interface driver usbfs
[ 0.213143] usbcore: registered new interface driver hub
[ 0.213267] usbcore: registered new device driver usb
[ 0.214945] clocksource: Switched to clocksource orion_clocksource
[ 0.300536] NET: Registered protocol family 2
[ 0.301865] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.301928] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.301981] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.302089] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.302127] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.302450] NET: Registered protocol family 1
[ 0.303095] RPC: Registered named UNIX socket transport module.
[ 0.303114] RPC: Registered udp transport module.
[ 0.303125] RPC: Registered tcp transport module.
[ 0.303136] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.303577] Unpacking initramfs...
[ 1.255435] Freeing initrd memory: 7012K (c1100000 - c17d9000)
[ 1.255624] NetWinder Floating Point Emulator V0.97 (double precision)
[ 1.257421] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 1.257536] audit: initializing netlink subsys (disabled)
[ 1.257631] audit: type=2000 audit(1.250:1): initialized
[ 1.258194] Initialise system trusted keyring
[ 1.258853] zbud: loaded
[ 1.259312] VFS: Disk quotas dquot_6.6.0
[ 1.259404] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.260265] NFS: Registering the id_resolver key type
[ 1.260351] Key type id_resolver registered
[ 1.260364] Key type id_legacy registered
[ 1.260405] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.260426] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 1.260772] jffs2: version 2.2. (NAND) (SUMMARY) <C2><A9> 2001-2006 Red Hat, Inc.
[ 1.261574] Key type big_key registered
[ 1.292341] Key type asymmetric registered
[ 1.292377] Asymmetric key parser 'x509' registered
[ 1.292537] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.292568] io scheduler noop registered
[ 1.292592] io scheduler deadline registered
[ 1.292693] io scheduler cfq registered (default)
[ 1.294756] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 1.296193] irq: Cannot allocate irq_descs @ IRQ32, assuming pre-allocated
[ 1.296846] irq: Cannot allocate irq_descs @ IRQ64, assuming pre-allocated
[ 1.297662] mv_xor f1060800.xor: Marvell shared XOR driver
[ 1.336046] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 1.336440] mv_xor f1060900.xor: Marvell shared XOR driver
[ 1.376018] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 1.376854] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 1.379070] console [ttyS0] disabled
[ 1.379175] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 10416666) is a 16550A
[ 1.969260] console [ttyS0] enabled
[ 1.974874] nand: Could not find valid ONFI parameter page; aborting
[ 1.981304] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda
[ 1.987657] nand: Hynix NAND 256MiB 3,3V 8-bit
[ 1.992085] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.999667] Scanning device for bad blocks
[ 2.144862] libphy: Fixed MDIO Bus: probed
[ 2.149651] libphy: orion_mdio_bus: probed
[ 2.154184] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 2.161889] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.168603] ehci-pci: EHCI PCI platform driver
[ 2.173141] ehci-orion: EHCI orion driver
[ 2.177459] orion-ehci f1050000.ehci: EHCI Host Controller
[ 2.182964] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 2.190926] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[ 2.214990] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 2.221347] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.228156] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.235380] usb usb1: Product: EHCI Host Controller
[ 2.240244] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd
[ 2.246860] usb usb1: SerialNumber: f1050000.ehci
[ 2.252680] hub 1-0:1.0: USB hub found
[ 2.256548] hub 1-0:1.0: 1 port detected
[ 2.261915] mousedev: PS/2 mouse device common for all mice
[ 2.268566] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0
[ 2.275760] i2c /dev entries driver
[ 2.281130] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.287212] drop_monitor: Initializing network drop monitor service
[ 2.293854] NET: Registered protocol family 17
[ 2.298740] Key type dns_resolver registered
[ 2.304245] registered taskstats version 1
[ 2.308450] Loading compiled-in X.509 certificates
[ 2.313323] zswap: loaded using pool lzo/zbud
[ 2.331302] Key type encrypted registered
[ 2.336667] rtc-mv f1010300.rtc: setting system clock to 2013-01-01 04:14:56 UTC (1357013696)
[ 2.349081] Freeing unused kernel memory: 296K (c07d8000 - c0822000)
Loading, please wait...
[ 2.463843] systemd-udevd[79]: starting version 215
[ 2.478252] random: systemd-udevd urandom read with 3 bits of entropy available
[ 2.575149] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 2.735715] usb 1-1: New USB device found, idVendor=058f, idProduct=6254
[ 2.742443] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.765235] hub 1-1:1.0: USB hub found
[ 2.773282] hub 1-1:1.0: 4 ports detected
[ 3.054991] usb 1-1.4: new high-speed USB device number 3 using orion-ehci
[ 3.186811] usb 1-1.4: New USB device found, idVendor=154b, idProduct=009f
[ 3.193688] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.201021] usb 1-1.4: Product: USB 2.0 FD
[ 3.205130] usb 1-1.4: Manufacturer: PNY Technologies
[ 3.210163] usb 1-1.4: SerialNumber: 0400000000015713
[ 3.240933] SCSI subsystem initialized
[ 3.252249] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[ 3.259328] scsi host0: usb-storage 1-1.4:1.0
[ 3.266808] usbcore: registered new interface driver usb-storage
[ 3.277720] usbcore: registered new interface driver uas
[ 4.532606] scsi 0:0:0:0: Direct-Access PNY USB 2.0 FD 1100 PQ: 0 ANSI: 4
[ 4.554163] sd 0:0:0:0: [sda] 15826944 512-byte logical blocks: (8.10 GB/7.54 GiB)
[ 4.564384] sd 0:0:0:0: [sda] Write Protect is off
[ 4.570109] sd 0:0:0:0: [sda] No Caching mode page found
[ 4.575487] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 4.588946] sda: sda1
[ 4.595989] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 4.608362] sd 0:0:0:0: Attached scsi generic sg0 type 0
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
modprobe: module ext3 not found in modules.dep
Begin: Checking root file system ... fsck from util-linux 2.25.2
fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sda1
fsck exited with status code 8
done.
Warning: File system check failed but did not detect errors
[ 18.151189] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 18.171744] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[ESC[36minfoESC[39;49m] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: udevd[ 19.949053] systemd-udevd[282]: starting version 215
ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c.
[....] Synthesizing the initial hotplug events...ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0cdone.
[....] Waiting for /dev to be fully populated...[ 20.621720] orion_wdt: Initial timeout 25 sec
[ 20.658836] marvell-cesa: probe of f1030000.crypto failed with error -524
[ 20.721949] random: nonblocking pool is initialized
ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0cdone.
[....] Activating swap...ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0cdone.
[ 22.670267] EXT4-fs (sda1): re-mounted. Opts: (null)
[....] Checking root file system...fsck from util-linux 2.25.2
rootfs: clean, 14518/494832 files, 167035/1978315 blocks
ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0cdone.
[ 24.487097] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[....] Activating lvm and md swap...ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0cdone.
[....] Checking file systems...fsck from util-linux 2.25.2
ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0cdone.
[....] Loading kernel modules...ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0cdone.
[....] Cleaning up temporary files... /tmpESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c.
[....] Mounting local filesystems...ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0cdone.
[....] Activating swapfile swap...ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0cdone.
[....] Cleaning up temporary files...ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c.
[....] Setting kernel variables ...ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0cdone.
[ 28.245861] NET: Registered protocol family 10
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1
Copyright 2004-2014 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Cannot find device "eth0"
Bind socket to interface: No such device
If you think you have received this message due to a bug rather
than a configuration issue please read the section on submitting
bugs on either our web page at www.isc.org or in the README file
before submitting a bug. These pages explain the proper
process and the information we find helpful for debugging..
exiting.
Failed to bring up eth0.
ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0cdone.
[....] Starting rpcbind daemon...ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c.
[....] Starting NFS common utilities: statd idmapdESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c.
[....] Cleaning up temporary files...ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c.
^MINIT: Entering runlevel: 2^M
[ESC[36minfoESC[39;49m] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1165 (syslogd)
ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c.
[....] Starting system message bus: dbusESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c.
[....] Starting NFS common utilities: statd idmapdESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c.
[....] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemonESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c.
[....] Not starting NFS kernel daemon: no exports. ...ESC[?25lESC[?1cESC7ESC[1G[ESC[33mwarnESC[39;49mESC8ESC[?25hESC[?0c ESC[33m(warning).ESC[39;49m
[....] Starting NTP server: ntpdESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c.
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1163 (klogd)
ESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c.
[....] Starting OpenBSD Secure Shell server: sshdESC[?25lESC[?1cESC7ESC[1G[ESC[32m ok ESC[39;49mESC8ESC[?25hESC[?0c.
^M
Debian GNU/Linux 8 debian ttyS0
debian login: root^M
Password:
Last login: Mon Dec 31 20:08:40 PST 2012 on ttyS0
Linux debian 4.4.0-kirkwood-tld-1 #1 PREEMPT Mon Jan 25 20:35:24 PST 2016 armv5tel
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
root@debian:~# ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
root@debian:~#
|
Re: Debian on Verbatim MediaShare Mini September 07, 2016 12:04AM |
Admin Registered: 13 years ago Posts: 18,564 |