SirK79
NSA310 how to install debian on fresh HDD September 09, 2016 05:15PM |
Re: NSA310 how to install debian on fresh HDD September 09, 2016 07:32PM |
Admin Registered: 13 years ago Posts: 18,580 |
Quote
This Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 is to keep in sync with kernel Linux-4.4.0-kirkwood-tld-1.
Basic minimal Debian Kirkwood rootfs for most Kirwood plugs:
- tarball size: 137M
- install size: 398M
- a basic jessie rootfs.
- The init system used in this rootfs is sysvinit . To boot with systemd, see note 2 below.
- Installed packages: nano, avahi, ntp, busybox-syslogd (log to RAM), htop, isc-dhcp-client, dialog, bzip2, nfs server/client, iperf, ethtool, sysvinit-core, sysvinit, and sysvinit-utils.
- see LED controls in /etc/rc.local, and /etc/init.d/halt
- see some useful aliases in /root/.profile
- root password: root
SirK79
Re: NSA310 how to install debian on fresh HDD September 10, 2016 08:28AM |
U-Boot 2013.07 (Sep 20 2013 - 15:45:03) ZyXEL NSA310 1-Bay Power Media Server SoC: Kirkwood 88F6281_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 PHY reset timed out MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 NSA310> usb start (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found NSA310> setenv load_dtb 'ext2load usb 0:1 0x1c00000 /boot/dts/kirkwood-goflexnet.dtb' NSA310> setenv load_initrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd' NSA310> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' NSA310> run load_dtb 11897 bytes read in 559 ms (20.5 KiB/s) NSA310> run load_uimage 3167962 bytes read in 385 ms (7.8 MiB/s) NSA310> run load_initrd 7179935 bytes read in 477 ms (14.4 MiB/s) NSA310> bootm 0x800000 0x1100000 0x1c00000 ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.4.0-kirkwood-tld-1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3167898 Bytes = 3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.4.0-kirkwood-tld-1 Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7179871 Bytes = 6.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f465000, end 0fb3de5f ... OK Loading Device Tree to 0f45f000, end 0f464e78 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Mon Jan 25 20:35:24 PST 2016 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine model: ZyXEL NSA310 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 250576K/262144K available (6007K kernel code, 573K rwdata, 1992K rodata, 296K init, 312K bss, 11568K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc07d7ef4 (8000 kB) [ 0.000000] .init : 0xc07d8000 - 0xc0822000 ( 296 kB) [ 0.000000] .data : 0xc0822000 - 0xc08b169c ( 574 kB) [ 0.000000] .bss : 0xc08b169c - 0xc08ff9d0 ( 313 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000009] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000326] Console: colour dummy device 80x30 [ 0.000357] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256) [ 0.090099] pid_max: default: 32768 minimum: 301 [ 0.090210] Security Framework initialized [ 0.090287] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090307] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.091157] Initializing cgroup subsys io [ 0.091192] Initializing cgroup subsys devices [ 0.091216] Initializing cgroup subsys freezer [ 0.091247] Initializing cgroup subsys net_cls [ 0.091329] CPU: Testing write buffer coherency: ok [ 0.091784] Setting up static identity map for 0x8200 - 0x8258 [ 0.092112] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.095764] devtmpfs: initialized [ 0.101186] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.101648] prandom: seed boundary self test passed [ 0.105387] prandom: 100 self tests passed [ 0.105413] pinctrl core: initialized pinctrl subsystem [ 0.106787] NET: Registered protocol family 16 [ 0.107149] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.130106] cpuidle: using governor ladder [ 0.160105] cpuidle: using governor menu [ 0.160483] Feroceon L2: Enabling L2 [ 0.160529] Feroceon L2: Cache support initialised. [ 0.166181] No ATAGs? [ 0.201603] vgaarb: loaded [ 0.201980] usbcore: registered new interface driver usbfs [ 0.202062] usbcore: registered new interface driver hub [ 0.202125] usbcore: registered new device driver usb [ 0.203163] clocksource: Switched to clocksource orion_clocksource [ 0.258235] NET: Registered protocol family 2 [ 0.259042] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.259080] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.259112] TCP: Hash tables configured (established 2048 bind 2048) [ 0.259180] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.259204] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.259399] NET: Registered protocol family 1 [ 0.259806] RPC: Registered named UNIX socket transport module. [ 0.259819] RPC: Registered udp transport module. [ 0.259827] RPC: Registered tcp transport module. [ 0.259834] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.260191] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.261226] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.261298] audit: initializing netlink subsys (disabled) [ 0.261348] audit: type=2000 audit(0.250:1): initialized [ 0.261696] Initialise system trusted keyring [ 0.262083] zbud: loaded [ 0.262374] VFS: Disk quotas dquot_6.6.0 [ 0.262435] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.262983] NFS: Registering the id_resolver key type [ 0.263022] Key type id_resolver registered [ 0.263032] Key type id_legacy registered [ 0.263058] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.263073] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.263365] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.263902] Key type big_key registered [ 0.275246] Key type asymmetric registered [ 0.275269] Asymmetric key parser 'x509' registered [ 0.275361] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.275384] io scheduler noop registered [ 0.275400] io scheduler deadline registered [ 0.275460] io scheduler cfq registered (default) [ 0.276867] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 0.277549] irq: Cannot allocate irq_descs @ IRQ33, assuming pre-allocated [ 0.277977] irq: Cannot allocate irq_descs @ IRQ65, assuming pre-allocated [ 0.278821] mvebu-pcie mbus:pcie-controller: PCI host bridge to bus 0000:00 [ 0.278841] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 0.278855] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 0.278869] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.279281] PCI: bus0: Fast back to back transfers disabled [ 0.279307] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.293350] PCI: bus1: Fast back to back transfers disabled [ 0.293537] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 0.293552] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff] [ 0.293572] pci 0000:01:00.0: BAR 6: assigned [mem 0xe0000000-0xe000ffff pref] [ 0.293589] pci 0000:01:00.0: BAR 4: assigned [mem 0xe0010000-0xe0013fff 64bit pref] [ 0.293613] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0014000-0xe0014fff 64bit pref] [ 0.293635] pci 0000:01:00.0: BAR 0: assigned [io 0x10000-0x100ff] [ 0.293650] pci 0000:00:01.0: PCI bridge to [bus 01] [ 0.293663] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 0.293678] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 0.293765] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 0.294064] mv_xor f1060800.xor: Marvell shared XOR driver [ 0.333843] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 0.334068] mv_xor f1060900.xor: Marvell shared XOR driver [ 0.373842] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 0.374317] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.375723] console [ttyS0] disabled [ 0.375787] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 1.058784] console [ttyS0] enabled [ 1.063615] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1 [ 1.069999] nand: Samsung NAND 128MiB 3,3V 8-bit [ 1.074670] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.082284] Scanning device for bad blocks [ 1.168283] Bad eraseblock 848 at 0x000006a00000 [ 1.192330] libphy: Fixed MDIO Bus: probed [ 1.196902] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.203548] ehci-pci: EHCI PCI platform driver [ 1.208088] ehci-orion: EHCI orion driver [ 1.212300] orion-ehci f1050000.ehci: EHCI Host Controller [ 1.217915] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 1.225873] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 1.243186] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 1.249458] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.256307] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.263587] usb usb1: Product: EHCI Host Controller [ 1.268485] usb usb1: Manufacturer: Linux 4.4.0-kirkwood-tld-1 ehci_hcd [ 1.275148] usb usb1: SerialNumber: f1050000.ehci [ 1.280605] hub 1-0:1.0: USB hub found [ 1.284457] hub 1-0:1.0: 1 port detected [ 1.289394] mousedev: PS/2 mouse device common for all mice [ 1.295725] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 1.302799] i2c /dev entries driver [ 1.309617] hidraw: raw HID events driver (C) Jiri Kosina [ 1.315511] drop_monitor: Initializing network drop monitor service [ 1.322061] NET: Registered protocol family 17 [ 1.326839] Key type dns_resolver registered [ 1.331936] registered taskstats version 1 [ 1.336135] Loading compiled-in X.509 certificates [ 1.341013] zswap: loaded using pool lzo/zbud [ 1.346489] Key type encrypted registered [ 1.351145] rtc-mv f1010300.rtc: setting system clock to 2016-09-10 13:25:48 UTC (1473513948) [ 1.361416] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6 [ 1.369016] Please append a correct "root=" boot option; here are the available partitions: [ 1.377516] 1f00 131072 mtdblock0 (driver?) [ 1.382605] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 1.390907] CPU: 0 PID: 1 Comm: swapper Not tainted 4.4.0-kirkwood-tld-1 #1 [ 1.397896] Hardware name: Marvell Kirkwood (Flattened Device Tree) [ 1.404223] [<c0016784>] (unwind_backtrace) from [<c00129f8>] (show_stack+0x10/0x14) [ 1.412006] [<c00129f8>] (show_stack) from [<c00c2200>] (panic+0x80/0x214) [ 1.418922] [<c00c2200>] (panic) from [<c07d9280>] (mount_block_root+0x204/0x24c) [ 1.426444] [<c07d9280>] (mount_block_root) from [<c07d93b4>] (mount_root+0xec/0x118) [ 1.434318] [<c07d93b4>] (mount_root) from [<c07d9504>] (prepare_namespace+0x124/0x184) [ 1.442358] [<c07d9504>] (prepare_namespace) from [<c07d8e9c>] (kernel_init_freeable+0x208/0x258) [ 1.451283] [<c07d8e9c>] (kernel_init_freeable) from [<c05b16b4>] (kernel_init+0x8/0xe4) [ 1.459417] [<c05b16b4>] (kernel_init) from [<c000f090>] (ret_from_fork+0x14/0x24) [ 1.467027] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
SirK79
Re: NSA310 how to install debian on fresh HDD September 10, 2016 09:49AM |
NSA310> printenv CASset=min CONTRY_TYPE=FF FEATURE_BIT=00 MALLOC_len=3 MODEL_ID=A203 PRODUCT_NAME=NSA-310 VENDOR_NAME=ZyXEL Communications Corp. arcNumber=4022 autoload=no baudrate=115200 bootargs=console=ttyS0,115200 root=/dev/sda3 bootargs_end=:::DB88FXX81:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=ide reset; ext2load ide 0:1 0x800000 /uImage-3.2; bootm 0x800000 bootdelay=2 console=100000 disL2Cache=no disL2Prefetch=yes disaMvPnp=no enaAutoRecovery=yes enaCpuStream=no enaDCPref=yes enaICPref=yes enaMonExt=no enaWrAllo=no eth1addr=00:19:CB:00:51:82 eth1mtu=1500 ethact=egiga0 ethaddr=50:67:F0:69:55:7D ethmtu=1500 ethprime=egiga1 hddPowerCtrl=no image_name=uImage ipaddr=10.4.50.165 kernel_addr=0x4640000 loadaddr=0x02000000 loads_echo=0 mainlineLinux=yes mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs nandEcc=1bit nandEnvBase=100000 netbsd_en=no netmask=255.255.255.0 netretry=no pcieTune=no pexMode=RC rcvrip=169.254.100.100 rootpath=/mnt/ARM_FS/ run_diag=yes sata_dma_mode=yes serverip=10.4.50.5 setL2CacheWT=yes standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 1464/131068 bytes
NSA310> ide reset Reset IDE: Bus 0: OK Bus 1: not available Device 0: Model: ST250LT007-9ZV14C Firm: 0001DEM1 Ser#: W0Q022GJ Type: Hard Disk Supports 48-bit addressing Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
usb start (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found
Re: NSA310 how to install debian on fresh HDD September 10, 2016 03:49PM |
Admin Registered: 13 years ago Posts: 18,580 |
NSA310> setenv load_dtb 'ext2load usb 0:1 0x1c00000 /boot/dts/kirkwood-goflexnet.dtb' NSA310> setenv load_initrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd' NSA310> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
setenv load_dtb 'ext2load ide 0:1 0x1c00000 /boot/dts/kirkwood-nsa310.dtb' setenv load_initrd 'ext2load ide 0:1 0x1100000 /boot/uInitrd' setenv load_uimage 'ext2load ide 0:1 0x800000 /boot/uImage'
Quote
4. Create uImage with embedded DTB for booting with older u-boots (2012 or earlier). Skip this step if you have installed the latest U-Boot for Kirkwood (or are installing this u-boot at the same time).
Please replace kirkwood-goflexnet.dtb below with the correct DTB name for your box (see the folder /media/sdb1/boot/dts).
Generate the uImage with DTB embedded inside:
cd /media/sdb1/boot
cp -a zImage-4.4.0-kirkwood-tld-1 zImage.fdt
cat dts/kirkwood-goflexnet.dtb >> zImage.fdt
mv uImage uImage.orig
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-4.4.0-kirkwood-tld-1 -d zImage.fdt uImage
sync
mv uImage uImage.nsa310 mv uImage.orig uImage
SirK79
Re: NSA310 how to install debian on fresh HDD September 10, 2016 05:17PM |
Re: NSA310 how to install debian on fresh HDD September 10, 2016 05:24PM |
Admin Registered: 13 years ago Posts: 18,580 |
AdamPL
Re: NSA310 how to install debian on fresh HDD September 12, 2016 09:47AM |
Re: NSA310 how to install debian on fresh HDD September 12, 2016 12:56PM |
Admin Registered: 13 years ago Posts: 18,580 |
Updated 20 Feb 2016: This Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2 is to keep in sync with kernel Linux-4.4.0-kirkwood-tld-1. Basic minimal Debian Kirkwood rootfs for most Kirwood plugs: - tarball size: 137M - install size: 398M - a basic jessie rootfs. - The init system used in this rootfs is sysvinit . To boot with systemd, see note 2 below. - Installed packages: nano, avahi, ntp, busybox-syslogd (log to RAM), htop, isc-dhcp-client, dialog, bzip2, nfs server/client, iperf, ethtool, sysvinit-core, sysvinit, and sysvinit-utils. - see LED controls in /etc/rc.local, and /etc/init.d/halt - see some useful aliases in /root/.profile - root password: root
SirK79
Re: NSA310 how to install debian on fresh HDD September 12, 2016 01:02PM |
Re: NSA310 how to install debian on fresh HDD September 12, 2016 01:17PM |
Admin Registered: 13 years ago Posts: 18,580 |
ll -R /sys/class/leds/
SirK79
Re: NSA310 how to install debian on fresh HDD September 12, 2016 01:48PM |
krzysiek@NSA310:~$ ls -l -R /sys/class/leds/ /sys/class/leds/: total 0 lrwxrwxrwx 1 root root 0 Sep 12 19:46 nsa310:green:copy -> ../../devices/platform/gpio-leds/leds/nsa310:green:copy lrwxrwxrwx 1 root root 0 Sep 12 19:46 nsa310:green:esata -> ../../devices/platform/gpio-leds/leds/nsa310:green:esata lrwxrwxrwx 1 root root 0 Sep 12 19:46 nsa310:green:hdd -> ../../devices/platform/gpio-leds/leds/nsa310:green:hdd lrwxrwxrwx 1 root root 0 Sep 12 19:46 nsa310:green:sys -> ../../devices/platform/gpio-leds/leds/nsa310:green:sys lrwxrwxrwx 1 root root 0 Sep 12 19:46 nsa310:green:usb -> ../../devices/platform/gpio-leds/leds/nsa310:green:usb lrwxrwxrwx 1 root root 0 Sep 12 19:46 nsa310:red:copy -> ../../devices/platform/gpio-leds/leds/nsa310:red:copy lrwxrwxrwx 1 root root 0 Sep 12 19:46 nsa310:red:esata -> ../../devices/platform/gpio-leds/leds/nsa310:red:esata lrwxrwxrwx 1 root root 0 Sep 12 19:46 nsa310:red:hdd -> ../../devices/platform/gpio-leds/leds/nsa310:red:hdd lrwxrwxrwx 1 root root 0 Sep 12 19:46 nsa310:red:sys -> ../../devices/platform/gpio-leds/leds/nsa310:red:sys lrwxrwxrwx 1 root root 0 Sep 12 19:46 nsa310:red:usb -> ../../devices/platform/gpio-leds/leds/nsa310:red:usb
SirK79
Re: NSA310 how to install debian on fresh HDD September 12, 2016 01:57PM |
Re: NSA310 how to install debian on fresh HDD September 12, 2016 02:28PM |
Admin Registered: 13 years ago Posts: 18,580 |
> root@NSA310:/home/krzysiek# echo 1 > > /sys/class/leds/nsa310\:green\:hdd/brightness > root@NSA310:/home/krzysiek# echo 0 > > /sys/class/leds/nsa310\:green\:hdd/brightnes >>
echo default-on > /sys/class/leds/nsa310:green:sys/trigger
SirK79
Re: NSA310 how to install debian on fresh HDD September 12, 2016 05:39PM |
if [ -d /sys/class/leds/nsa310\:green\:sys ]; then echo default-on > /sys/class/leds/nsa310\:green\:sys/trigger echo none > /sys/class/leds/nsa310:orange:sys/trigger fi if [ -d /sys/class/leds/nsa310\:green\:hdd ]; then echo ide-disk1 > /sys/class/leds/nsa310\:green\:hdd/trigger fi if [ -d /sys/class/leds/nsa310\:green\:esata ]; then echo ide-disk2 > /sys/class/leds/nsa310\:green\:esata/trigger fi if [ -d /sys/class/leds/nsa310\:green\:usb ]; then echo usb-host > /sys/class/leds/nsa310\:green\:usb/trigger fi
Re: NSA310 how to install debian on fresh HDD September 13, 2016 12:35AM |
Admin Registered: 13 years ago Posts: 18,580 |
U-Boot 2013.07 (Sep 20 2013 - 15:45:03) ZyXEL NSA310 1-Bay Power Media Server
SirK79
Re: NSA310 how to install debian on fresh HDD September 13, 2016 04:52AM |
SirK79
Re: NSA310 how to install debian on fresh HDD September 14, 2016 10:58AM |
Re: NSA310 how to install debian on fresh HDD September 14, 2016 02:14PM |
Admin Registered: 13 years ago Posts: 18,580 |
/boot/dts/kirkwood-nsa310a.dtb /boot/dts/kirkwood-nsa310b-lmsensor-redusbled.dtb /boot/dts/kirkwood-nsa310.dtb
Re: NSA310 how to install debian on fresh HDD September 14, 2016 03:49PM |
Registered: 7 years ago Posts: 2 |
U-Boot 2013.07 (Sep 20 2013 - 15:45:03) ZyXEL NSA310 1-Bay Power Media Server SoC: Kirkwood 88F6281_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 PHY reset timed out MV88E1318 PHY initialized on egiga0
root@nsa310:~# lscpu Architecture: armv5tel Byte Order: Little Endian CPU(s): 1 On-line CPU(s) list: 0 Thread(s) per core: 1 Core(s) per socket: 1 Socket(s): 1 Model name: Feroceon 88FR131 rev 1 (v5l)
Re: NSA310 how to install debian on fresh HDD September 14, 2016 03:57PM |
Registered: 7 years ago Posts: 2 |