Pogo plug stuck at "bad magic number" March 07, 2017 10:19PM |
Registered: 7 years ago Posts: 1 |
Reading data from 0x2ff800 -- 100% complete. 2097152 bytes read: OK ## Booting image at 00800000 ... Bad Magic Number CE>>
U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Using egiga0 device ping failed; host 192.168.1.100 is not alive Hit any key to stop autoboot: 0 (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found ** Bad device usb 0 ** ** Bad device usb 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! MMC rescan: current device # 0 initialized OK ** No partition table - mmc 0 ** ** No partition table - mmc 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! Reset IDE: ide_preinit failed ** Bad device size - ide 0 ** ** Bad device size - ide 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=4" UBI: MTD device size: 112 MiB UBI: number of good PEBs: 896 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 0 UBI: total number of reserved PEBs: 896 UBI: number of PEBs reserved for bad PEB handling: 8 UBI: max/mean erase counter: 1/0 UBIFS: recovery needed UBIFS: recovery deferred UBIFS: mounted UBI device 0, volume 0, name "rootfs" UBIFS: mounted read-only UBIFS: file system size: 110850048 bytes (108252 KiB, 105 MiB, 873 LEBs) UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: LZO UBIFS: reserved for root: 0 bytes (0 KiB) Loading file 'uboot.mtd0.dockstar.original.kwb' to addr 0x00800000 with size 524288 (0x00080000)... Done ## Starting application at 0x00800200 ... U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: MV88F6192 Rev 3 (DDR2) CPU running @ 800Mhz L2 running @ 400Mhz SysClock = 200Mhz , TClock = 166Mhz DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB *** Warning - bad CRC or NAND, using default environment CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD (GUESSED): REDSTONE:0.1 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x200000 Reading data from 0x2ff800 -- 100% complete. 2097152 bytes read: OK ## Booting image at 00800000 ... Bad Magic Number CE>>
U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: kwsdio: 0 In: serial Out: serial Err: serial Net: egiga0 Using egiga0 device ping failed; host 192.168.1.100 is not alive Hit any key to stop autoboot: 0 (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found ** Bad device usb 0 ** ** Bad device usb 0 ** Wrong Image Format for bootm command ERROR: can't get kernel image! MMC rescan: current device # 0 initialized OK 2461416 bytes read in 1241 ms (1.9 MiB/s) 6362802 bytes read in 1540 ms (3.9 MiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-3.14.0-kirkwood-tld-1 Created: 2014-04-06 20:44:27 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2461352 Bytes = 2.3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-3.14.0-kirkwood-tld-1 Created: 2014-04-06 20:44:41 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6362738 Bytes = 6.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK Using machid 0xf78 from environment Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.14.0-kirkwood-tld-1 (root@tldDebian) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 PREEMPT Tue Apr 1 22:54:58 PDT 2014 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977 [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: Pogoplug V4 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Re: Pogo plug stuck at "bad magic number" March 07, 2017 11:45PM |
Admin Registered: 13 years ago Posts: 18,558 |
su cd /media/sdb1 cp -aR /media/sda1/* . sync
Re: Pogo plug stuck at "bad magic number" March 07, 2017 11:51PM |
Admin Registered: 13 years ago Posts: 18,558 |
gaurav
Re: Pogo plug stuck at "bad magic number" May 27, 2017 03:50AM |