My Cloud Mirror Gen2 u-boot July 05, 2017 12:04PM |
Registered: 7 years ago Posts: 119 |
$ gunzip u-boot-a38x-GrandTeton_2014T3_PQ-nand-uart.bin.gz
./kwboot -f -t -B 115200 /dev/ttyUSB0 -b u-boot-a38x-GrandTeton_2014T3_PQ-nand-uart.bin -s 0 -q 1
mcmg2
Re: My Cloud Mirror Gen2 July 05, 2017 09:23PM |
mcmg2
Re: My Cloud Mirror Gen2 July 05, 2017 09:28PM |
-^Cmint@mint ~/kwboot $ sudo ./kwboot -f -t -B 115200 /dev/ttyUSB0 -b u-boot-a38randTeton_2014T3_PQ-nand-uart.bin -s 0 -q 1 Sending boot message. Please reboot the target...| BootRO/ - 1.73 Bootin from NAND flash General -nitialization - Version: 1.0.0 Detected Device ID 6820 High sp\ed PHY - Versio: 2.0 Load WD GrandTeton Serdes Config: boar| SerDes lanes topology details: | Lane # | Speed | Tpe / | -------------------------------- | 0 | 06 | SAT-0 | | 1 | 05 | PCIe0 | | 2 | 06 | SAA1 | \| 3 | 05 | USB3 HOST1 | | 4 | 05 | US3 HOST| | | 5 | 00 | SGMII2 --------------------------/-- |PCIe, /dx 0: detected no link High speed PHY - Ended Successfully DD-3 Training Sequence - Ver TIP-1.26.0 m\SysEnvGetTopologyUpdateInfo: TWSI Read failed |DDR/ Training Sequence - Swtching XBAR Winow to FastPath Window -DR3 Training Sequence - Ended Successfully |BootROM: Image checksum ver/ficatio\ PASSE|
mcmg2
Re: My Cloud Mirror Gen2 July 05, 2017 09:32PM |
mcmg2
Re: My Cloud Mirror Gen2 July 05, 2017 09:36PM |
mint@mint ~/kwboot $ sudo ./kwboot -f -t -B 115200 /dev/ttyUSB0 -b u-boot-a38x-GrandTeton_2014T3_PQ-nand-uart.bin -s 0 -q 1 Sending boot message. Please reboot the target...- Sending boot image... 0 % [+.....................................................................] 0 % [......................................................................] 1 % [......................................................................] 2 % [......................................................................] 3 % [......................................................................] 4 % [......................................................................] 5 % [......................................................................] 6 % [......................................................................] 7 % [......................................................................] 8 % [......................................................................] 9 % [......................................................................] 10 % [......................................................................] 11 % [......................................................................] 12 % [......................................................................] 13 % [......................................................................] 14 % [......................................................................] 15 % [......................................................................] 15 % [......................................................................] 16 % [......................................................................] 17 % [......................................................................] 18 % [......................................................................] 19 % [......................................................................] 20 % [......................................................................] 21 % [......................................................................] 22 % [......................................................................] 23 % [......................................................................] 24 % [......................................................................] 25 % [......................................................................] 26 % [......................................................................] 27 % [......................................................................] 28 % [......................................................................] 29 % [......................................................................] 30 % [......................................................................] 30 % [......................................................................] 31 % [......................................................................] 32 % [......................................................................] 33 % [......................................................................] 34 % [......................................................................] 35 % [......................................................................] 36 % [......................................................................] 37 % [......................................................................] 38 % [......................................................................] 39 % [......................................................................] 40 % [......................................................................] 41 % [......................................................................] 42 % [......................................................................] 43 % [......................................................................] 44 % [......................................................................] 45 % [......................................................................] 45 % [......................................................................] 46 % [......................................................................] 47 % [......................................................................] 48 % [......................................................................] 49 % [......................................................................] 50 % [......................................................................] 51 % [......................................................................] 52 % [......................................................................] 53 % [......................................................................] 54 % [......................................................................] 55 % [......................................................................] 56 % [......................................................................] 57 % [......................................................................] 58 % [......................................................................] 59 % [......................................................................] 60 % [......................................................................] 60 % [......................................................................] 61 % [......................................................................] 62 % [......................................................................] 63 % [......................................................................] 64 % [......................................................................] 65 % [......................................................................] 66 % [......................................................................] 67 % [......................................................................] 68 % [......................................................................] 69 % [......................................................................] 70 % [......................................................................] 71 % [......................................................................] 72 % [......................................................................] 73 % [......................................................................] 74 % [......................................................................] 75 % [......................................................................] 76 % [......................................................................] 76 % [......................................................................] 77 % [......................................................................] 78 % [......................................................................] 79 % [......................................................................] 80 % [......................................................................] 81 % [......................................................................] 82 % [......................................................................] 83 % [......................................................................] 84 % [......................................................................] 85 % [......................................................................] 86 % [......................................................................] 87 % [......................................................................] 88 % [......................................................................] 89 % [......................................................................] 90 % [......................................................................] 91 % [......................................................................] 91 % [......................................................................] 92 % [......................................................................] 93 % [......................................................................] 94 % [......................................................................] 95 % [......................................................................] 96 % [......................................................................] 97 % [......................................................................] 98 % [......................................................................] 99 % [.........................................] [Type Ctrl-\ + c to quit] __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01_v1.04 (Jul 05 2017 - 16:59:05) Marvell version: 2014_T3.0p6 mvBoardIdIndexGet(boardId) = 1 Board: GrandTeton DB6820 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 1 GiB Map: Code: 0x3fece000:0x3ff95f50 BSS: 0x3ffef254 Stack: 0x3f9cdf20 Heap: 0x3f9ce000:0x3fece000 raise: Signal # 8 caught raise: Signal # 8 caught U-Boot Environment: 0x00000000:0x00080000 (NAND) NAND: ID: daad ,256 MiB MMC: mv_sdh: 0 PCI-e 0: Detected No Link. USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Creating 1 MTD partitions on "nand0": 0x00000f500000-0x00000ff00000 : "mtd=7" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=7" UBI: MTD device size: 10 MiB UBI: number of good PEBs: 80 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 32 UBI: total number of reserved PEBs: 48 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 2/0 UBIFS: mounted UBI device 0, volume 0, name "reserve2" UBIFS: mounted read-only UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs) UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: LZO UBIFS: reserved for root: 200807 bytes (196 KiB) Loading file '/mac_addr' to addr 0x02000000 with size 18 (0x00000012)... Done Set lan 2 WakeOnLan ok Enable HD1 Enable HD2 Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | In-Band | | egiga1 | RGMII | In-Band | | egiga2 | SGMII | 0x00 | egiga0, egiga1, egiga2 [PRIME] Hit any key to stop autoboot: 0 Marvell>>finally...
Re: My Cloud Mirror Gen2 July 06, 2017 12:59AM |
Registered: 7 years ago Posts: 119 |
Quote
mcmg2
finally...
setenv bootdev usb setenv device '0:1' setenv dtb_file '/boot/dts/armada-385-wd-mcmg2.dtb' setenv load_dtb_addr 0x1000000 setenv load_initrd_addr 0x2900000 setenv load_image_addr 0x02000000 setenv load_dtb 'echo loading DTB $dtb_file ...; ext2load $bootdev $device $load_dtb_addr $dtb_file' setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/zImage' setenv usb_set_bootargs 'setenv bootargs "console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $mtdparts earlyprintk=serial"' setenv usb_bootcmd 'echo Booting from USB ...; setenv fdt_skip_update yes; usb start; run load_image; run load_dtb; run usb_set_bootargs; bootz $load_image_addr - $load_dtb_addr' setenv bootcmd_usb 'usb start; run usb_set_bootargs; run usb_bootcmd; reset' run bootcmd_usb
mcmg2
Re: My Cloud Mirror Gen2 July 06, 2017 02:19AM |
mint@mint ~/kwboot $ sudo ./kwboot -f -t -B 115200 /dev/ttyUSB0 -b u-boot-a38x-GrandTeton_2014T3_PQ-nand-uart.bin -s 0 -q 1 Sending boot message. Please reboot the target.../ Sending boot image... 0 % [+.....................................................................] 0 % [......................................................................] 1 % [......................................................................] 2 % [......................................................................] 3 % [......................................................................] 4 % [......................................................................] 5 % [......................................................................] 6 % [......................................................................] 7 % [......................................................................] 8 % [......................................................................] 9 % [......................................................................] 10 % [......................................................................] 11 % [......................................................................] 12 % [......................................................................] 13 % [......................................................................] 14 % [......................................................................] 15 % [......................................................................] 15 % [......................................................................] 16 % [......................................................................] 17 % [......................................................................] 18 % [......................................................................] 19 % [......................................................................] 20 % [......................................................................] 21 % [......................................................................] 22 % [......................................................................] 23 % [......................................................................] 24 % [......................................................................] 25 % [......................................................................] 26 % [......................................................................] 27 % [......................................................................] 28 % [......................................................................] 29 % [......................................................................] 30 % [......................................................................] 30 % [......................................................................] 31 % [......................................................................] 32 % [......................................................................] 33 % [......................................................................] 34 % [......................................................................] 35 % [......................................................................] 36 % [......................................................................] 37 % [......................................................................] 38 % [......................................................................] 39 % [......................................................................] 40 % [......................................................................] 41 % [......................................................................] 42 % [......................................................................] 43 % [......................................................................] 44 % [......................................................................] 45 % [......................................................................] 45 % [......................................................................] 46 % [......................................................................] 47 % [......................................................................] 48 % [......................................................................] 49 % [......................................................................] 50 % [......................................................................] 51 % [......................................................................] 52 % [......................................................................] 53 % [......................................................................] 54 % [......................................................................] 55 % [......................................................................] 56 % [......................................................................] 57 % [......................................................................] 58 % [......................................................................] 59 % [......................................................................] 60 % [......................................................................] 60 % [......................................................................] 61 % [......................................................................] 62 % [......................................................................] 63 % [......................................................................] 64 % [......................................................................] 65 % [......................................................................] 66 % [......................................................................] 67 % [......................................................................] 68 % [......................................................................] 69 % [......................................................................] 70 % [......................................................................] 71 % [......................................................................] 72 % [......................................................................] 73 % [......................................................................] 74 % [......................................................................] 75 % [......................................................................] 76 % [......................................................................] 76 % [......................................................................] 77 % [......................................................................] 78 % [......................................................................] 79 % [......................................................................] 80 % [......................................................................] 81 % [......................................................................] 82 % [......................................................................] 83 % [......................................................................] 84 % [......................................................................] 85 % [......................................................................] 86 % [......................................................................] 87 % [......................................................................] 88 % [......................................................................] 89 % [......................................................................] 90 % [......................................................................] 91 % [......................................................................] 91 % [......................................................................] 92 % [......................................................................] 93 % [......................................................................] 94 % [......................................................................] 95 % [......................................................................] 96 % [......................................................................] 97 % [......................................................................] 98 % [......................................................................] 99 % [.........................................] [Type Ctrl-\ + c to quit] __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01_v1.04 (Jul 05 2017 - 16:59:05) Marvell version: 2014_T3.0p6 mvBoardIdIndexGet(boardId) = 1 Board: GrandTeton DB6820 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 1 GiB Map: Code: 0x3fece000:0x3ff95f50 BSS: 0x3ffef254 Stack: 0x3f9cdf20 Heap: 0x3f9ce000:0x3fece000 raise: Signal # 8 caught raise: Signal # 8 caught U-Boot Environment: 0x00000000:0x00080000 (NAND) NAND: ID: daad ,256 MiB MMC: mv_sdh: 0 PCI-e 0: Detected No Link. USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Creating 1 MTD partitions on "nand0": 0x00000f500000-0x00000ff00000 : "mtd=7" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=7" UBI: MTD device size: 10 MiB UBI: number of good PEBs: 80 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 32 UBI: total number of reserved PEBs: 48 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 2/0 UBIFS: mounted UBI device 0, volume 0, name "reserve2" UBIFS: mounted read-only UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs) UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: LZO UBIFS: reserved for root: 200807 bytes (196 KiB) Loading file '/mac_addr' to addr 0x02000000 with size 18 (0x00000012)... Done Set lan 2 WakeOnLan ok Enable HD1 Enable HD2 Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | In-Band | | egiga1 | RGMII | In-Band | | egiga2 | SGMII | 0x00 | egiga0, egiga1, egiga2 [PRIME] Hit any key to stop autoboot: 0 Marvell>> setenv bootdev usb Marvell>> setenv device '0:1' Marvell>> setenv dtb_file '/boot/dts/armada-385-wd-mcmg2.dtb' Marvell>> setenv load_dtb_addr 0x1000000 Marvell>> setenv load_initrd_addr 0x2900000 Marvell>> setenv load_image_addr 0x02000000 Marvell>> setenv load_dtb 'echo loading DTB $dtb_file ...; ext2load $bootdev $device $load_dtb_addr $dtb_file' Marvell>> setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' Marvell>> setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage' Marvell>> setenv usb_set_bootargs 'setenv bootargs "console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $mtdparts earlyprintk=serial"' Marvell>> setenv usb_bootcmd 'echo Booting from USB ...; setenv fdt_skip_update yes; usb start; run load_image; run load_dtb; run usb_set_bootargs; bootz $load_image_addr - $load_dtb_addr' Marvell>> setenv bootcmd_usb 'usb start; run usb_set_bootargs; run usb_bootcmd; reset' Marvell>> run bootcmd_usb (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Booting from USB ... (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found loading Image ... ** Bad device usb 0 ** loading DTB /boot/dts/armada-385-wd-mcmg2.dtb ... ** Bad device usb 0 ** Bad Linux ARM zImage magic! resetting ... BootROM - 1.73 Booting from NAND flash General initialization - Version: 1.0.0 Detected Device ID 6820 High speed PHY - Version: 2.0 Load WD GrandTeton Serdes Config: board SerDes lanes topology details: | Lane # | Speed | Type | -------------------------------- | 0 | 06 | SATA0 | | 1 | 05 | PCIe0 | | 2 | 06 | SATA1 | | 3 | 05 | USB3 HOST1 | | 4 | 05 | USB3 HOST0 | | 5 | 00 | SGMII2 | -------------------------------- PCIe, Idx 0: detected no link High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.26.0 mvSysEnvGetTopologyUpdateInfo: TWSI Read failed DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01_v1.02 (Jun 25 2015 - 17:06:32) Marvell version: 2014_T3.0p6 mvBoardIdIndexGet(boardId) = 1 Board: GrandTeton DB6820 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB Map: Code: 0x1fece000:0x1ff95bd4 BSS: 0x1ffef254 Stack: 0x1f9cdf20 Heap: 0x1f9ce000:0x1fece000 raise: Signal # 8 caught raise: Signal # 8 caught U-Boot Environment: 0x00000000:0x00080000 (NAND) NAND: mvNfcInit mvNfcReset() ret = 0x0 read Nand Flash ID ID: daad ,nand reg = 0x.8ff8166 256 MiB MMC: mv_sdh: 0 PCI-e 0: Detected No Link. USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Creating 1 MTD partitions on "nand0": 0x00000f500000-0x00000ff00000 : "mtd=7" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=7" UBI: MTD device size: 10 MiB UBI: number of good PEBs: 80 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 32 UBI: total number of reserved PEBs: 48 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 2/0 UBIFS: mounted UBI device 0, volume 0, name "reserve2" UBIFS: mounted read-only UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs) UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: LZO UBIFS: reserved for root: 200807 bytes (196 KiB) Loading file '/mac_addr' to addr 0x02000000 with size 18 (0x00000012)... Done Set lan 2 WakeOnLan ok Enable HD1 Enable HD2 Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | In-Band | | egiga1 | RGMII | In-Band | | egiga2 | SGMII | 0x00 | egiga0, egiga1, egiga2 [PRIME] Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x500000, size 0x500000 5242880 bytes read: OK NAND read: device 0 offset 0xa00000, size 0x500000 5242880 bytes read: OK ## Booting image at 00a00000 ... ## Booting kernel from Legacy Image at 00a00000 ... Image Name: Linux-382 Created: 2015-08-02 3:54:03 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4093292 Bytes = 3.9 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 00f00000 ... Image Name: Ramdisk Created: 2015-10-13 10:23:23 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 2278194 Bytes = 2.2 MiB Load Address: 00e00000 Entry Point: 00e00000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Initializing cgroup subsys cpuset Initializing cgroup subsys cpu Initializing cgroup subsys cpuacct Linux version 3.10.39 (kman@kmachine) (gcc version 4.6.4 (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPAGESIZE ALIGN) ) #1 SMP Sun Aug 2 11:53:57 CST 2015 2014T30p5 Build-git3e9fe59 CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: Marvell Armada 380/381/382/385/388 (Device Tree), model: Marvell Armada 385 Development Board Memory policy: ECC disabled, Data cache writealloc PERCPU: Embedded 1 pages/cpu @c0930000 s8320 r8192 d16256 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16364 Kernel command line: root=/dev/ram console=ttyS0,115200 PID hash table entries: 2048 (order: -2, 8192 bytes) Dentry cache hash table entries: 65536 (order: 3, 262144 bytes) Inode-cache hash table entries: 32768 (order: 2, 131072 bytes) allocated 131072 bytes of page_cgroup please try 'cgroup_disable=memory' option if you don't want memory cgroups Memory: 512MB = 512MB total Memory: 511744k/511744k available, 12544k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff8000 ( 32 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xe0800000 - 0xfff00000 ( 503 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc0714278 (7217 kB) .init : 0xc0718000 - 0xc075a080 ( 265 kB) .data : 0xc075c000 - 0xc07a7e40 ( 304 kB) .bss : 0xc07a7e40 - 0xc0871570 ( 806 kB) Hierarchical RCU implementation. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. NR_IRQS:16 nr_irqs:16 16 LSP version: linux-3.10.39-2014_T3.0p5 sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms L310 cache controller enabled l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B Console: colour dummy device 80x30 Calibrating delay loop... 2655.84 BogoMIPS (lpj=13279232) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 4096 Initializing cgroup subsys memory Initializing cgroup subsys devices Initializing cgroup subsys freezer Initializing cgroup subsys blkio CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0xc056c2b0 - 0xc056c308 mvebu-pmsu: Initializing Power Management Service Unit Initializing CPU Reset module CPU1: Booted secondary processor CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 Brought up 2 CPUs SMP: Total of 2 processors activated (5311.69 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4 xor: measuring software checksum speed arm4regs : 1420.800 MB/sec 8regs : 940.800 MB/sec 32regs : 921.600 MB/sec xor: using function: arm4regs (1420.800 MB/sec) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations irq: Cannot allocate irq_descs @ IRQ196, assuming pre-allocated irq: Cannot allocate irq_descs @ IRQ228, assuming pre-allocated bio: create slab <bio-0> at 0 raid6: int32x1 355 MB/s raid6: int32x2 346 MB/s raid6: int32x4 446 MB/s raid6: int32x8 384 MB/s raid6: using algorithm int32x4 (446 MB/s) raid6: using intx1 recovery algorithm mvebu-pcie pcie-controller.3: PCIe0.0: link down mvebu-pcie pcie-controller.3: PCIe1.0: link down mvebu-pcie pcie-controller.3: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe8000000] pci_bus 0000:00: root bus resource [bus 00-ff] PCI: bus0: Fast back to back transfers disabled pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring PCI: bus1: Fast back to back transfers enabled PCI: bus2: Fast back to back transfers enabled pci 0000:00:01.0: PCI bridge to [bus 01] pci 0000:00:02.0: PCI bridge to [bus 02] PCI: enabling device 0000:00:01.0 (0140 -> 0143) PCI: enabling device 0000:00:02.0 (0140 -> 0143) SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> PTP clock support registered Switching to clocksource armada_370_xp_clocksource NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 0, 32768 bytes) TCP bind hash table entries: 4096 (order: 0, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP: reno registered UDP hash table entries: 1024 (order: 0, 32768 bytes) UDP-Lite hash table entries: 1024 (order: 0, 32768 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Trying to unpack rootfs image as initramfs... rootfs image is not initramfs (no cpio magic); looks like an initrd Freeing initrd memory: 2176K (c0f08000 - c1128000) VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 8192 (order 0, 32768 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher Installing knfsd (copyright (C) 1996 okir@monad.swb.de). fuse init (API version 7.22) SGI XFS with security attributes, large block/inode numbers, no debug enabled msgmni has been set to 1002 async_tx: api initialized (async) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver mv_xor f1060800.xor: Marvell shared XOR driver mv_xor f1060800.xor: Marvell XOR: ( xor cpy intr ) mv_xor f1060800.xor: freeing 1 in use descriptors! mv_xor f1060800.xor: Marvell XOR: ( crc32c ) mv_xor f1060900.xor: Marvell shared XOR driver mv_xor f1060900.xor: Marvell XOR: ( xor cpy intr ) mv_xor f1060900.xor: freeing 1 in use descriptors! mv_xor f1060900.xor: Marvell XOR: ( crc32c ) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A console [ttyS0] enabled f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 45) is a 16550A brd: module loaded loop: module loaded ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs scsi0 : ahci_mv_platform scsi1 : ahci_mv_platform ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58 ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58 armada-nand f10d0000.nand: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC Nand Flash Timing = [WP : 12], [WH : 10] NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix NAND 256MiB 3,3V 8-bit), 256MiB, page size: 2048, OOB size: 64 Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 8 ofpart partitions found on MTD device armada-nand Creating 8 MTD partitions on "armada-nand": 0x000000000000-0x000000500000 : "U-Boot" 0x000000500000-0x000000a00000 : "uImage" 0x000000a00000-0x000000f00000 : "uRamdisk" 0x000000f00000-0x00000c800000 : "image.cfs" 0x00000c800000-0x00000d700000 : "rescue fw" 0x00000d700000-0x00000eb00000 : "config" 0x00000eb00000-0x00000f500000 : "reserve1" 0x00000f500000-0x00000ff00000 : "reserve2" SoC: model = 0x6820, revision = 0x4 mvPncVirtBase = 0xe0e00000, pncTcamSize = 1024 o 3 Giga ports supported o SKB recycle supported (Disabled) o NETA acceleration mode 4 o BM supported for CPU: 4 BM pools o PnC supported (Enabled) o RX Queue support: 8 Queues * 256 Descriptors o TX Queue support: 8 Queues * 532 Descriptors o GSO supported o GRO supported o Receive checksum offload supported o Transmit checksum offload supported o Driver ERROR statistics enabled o Driver INFO statistics enabled o Driver DEBUG statistics enabled port #0: is_sgmii=0, is_rgmii=1, phy_addr=2 o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800 o Port 0 is connected to Linux netdevice o egiga0, ifindex = 2, GbE port = 0 giga p=0: mtu=1500, mac=00:50:43:02:02:01 (platform) port #1: is_sgmii=0, is_rgmii=1, phy_addr=1 o Loading network interface(s) for port #1: cpu_mask=0x3, tx_csum_limit=2048 o Port 1 is connected to Linux netdevice o egiga1, ifindex = 3, GbE port = 1 giga p=1: mtu=1500, mac=00:50:43:02:02:02 (platform) port #2: is_sgmii=1, is_rgmii=0, phy_addr=0 o Loading network interface(s) for port #2: cpu_mask=0x3, tx_csum_limit=2048 o Port 2 is connected to Linux netdevice o egiga2, ifindex = 4, GbE port = 2 giga p=2: mtu=1500, mac=00:50:43:02:02:03 (platform) libphy: orion_mdio_bus: probed mdio_bus f1072004.mdio-mi: cannot get PHY at address 2 mdio_bus f1072004.mdio-mi: cannot get PHY at address 1 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-orion: EHCI orion driver orion-ehci f1058000.usb: EHCI Host Controller orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 orion-ehci f1058000.usb: irq 50, io mem 0xf1058000 orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000 hub 4-0:1.0: USB hub found hub 4-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 hub 5-0:1.0: USB hub found hub 5-0:1.0: 1 port detected usbcore: registered new interface driver usb-storage ata1: SATA link down (SStatus 0 SControl 300) ata2: SATA link down (SStatus 0 SControl 300) usb 4-1: new high-speed USB device number 2 using xhci-hcd usb 4-1: ep 0x81 - rounding interval to 128 microframes, ep desc says 255 microframes usb 4-1: ep 0x2 - rounding interval to 128 microframes, ep desc says 255 microframes usb-storage 4-1:1.0: USB Mass Storage device detected scsi2 : usb-storage 4-1:1.0 mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 i2c /dev entries driver md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com dm_crypt using the OCF package. cpuidle: using governor ladder armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2 armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: chain(0) mvCesaInit: channels=2, session=640, queue=256 armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode cesadev_init(c0734f0c) TCP: cubic registered NET: Registered protocol family 17 8021q: 802.1Q VLAN Support v1.8 VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 registered taskstats version 1 mvebu-rtc f10a3800.rtc: setting system clock to 2017-07-06 07:15:56 UTC (1499325356) md: Waiting for all devices to be available before autodetect md: If you don't use raid, use raid=noautodetect md: Autodetecting RAID arrays. md: Scanned 0 and added 0 devices. md: autorun ... md: ... autorun DONE. RAMDISK: gzip image found at block 0 VFS: Mounted root (ext2 filesystem) readonly on device 1:0. devtmpfs: mounted Freeing unused kernel memory: 256K (c0718000 - c0758000) init started: BusyBox v1.20.2 (2014-10-30 15:28:59 CST) starting pid 1261, tty '': '/etc/rc.sh' ** Mounting /etc/fstab umount: can't umount /proc: Invalid argument umount: can't umount /usr/local/modules: Invalid argument scsi 2:0:0:0: Direct-Access SRT POLLEX 8G 1100 PQ: 0 ANSI: 4 sd 2:0:0:0: Attached scsi generic sg0 type 0 sd 2:0:0:0: [sda] 15728640 512-byte logical blocks: (8.05 GB/7.50 GiB) sd 2:0:0:0: [sda] Write Protect is off sd 2:0:0:0: [sda] No Caching mode page found sd 2:0:0:0: [sda] Assuming drive cache: write through sd 2:0:0:0: [sda] No Caching mode page found sd 2:0:0:0: [sda] Assuming drive cache: write through sda: sda1 sd 2:0:0:0: [sda] No Caching mode page found sd 2:0:0:0: [sda] Assuming drive cache: write through sd 2:0:0:0: [sda] Attached SCSI removable disk sh: hotPlug.sh: not found offset_flag=1,vaule_flag=1,bit_flag=0 offset_flag=1,vaule_flag=1,bit_flag=0 offset_flag=1,vaulUBI: attaching mtd5 to ubi0 e_flag=1,bit_flag=0 offset_flag=1,vaule_flag=1,bit_flag=0 UBI: scanning is finished UBI: attached mtd5 (name "config", size 20 MiB) to ubi0 UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 UBI: good PEBs: 160, bad PEBs: 0, corrupted PEBs: 0 UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 UBI: max/mean erase counter: 11/6, WL threshold: 4096, image sequence number: 1847991382 UBI: available PEBs: 22, total reserved PEBs: 138, PEBs reserved for bad PEB handling: 10 UBI: background thread "ubi_bgt0d" started, PID 1291 UBI device number 0, total 160 LEBs (20316160 bytes, 19.4 MiB), available 22 LEBs (2793472 bytes, 2.7 MiB), LEB size 126976 bytes (124.0 KiB) UBIFS: background thread "ubifs_bgt0_0" started, PID 1296 UBIFS: recovery needed UBIFS: recovery completed UBIFS: mounted UBI device 0, volume 0, name "config" UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS: FS size: 14475264 bytes (13 MiB, 114 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs) UBIFS: reserved for root: 683702 bytes (667 KiB) UBIFS: media format: w4/r0 (latest is w4/r0), UUID 12CDA789-300F-44B7-B437-4B5666A1DA39, small LPT model umount: can't umount /usr/local/tmp/image.cfs: No such file or directory rm: can't remove '/usr/local/tmp/image.cfs': No such file or directory umount: can't umount /usr/local/tmp: Invalid argument first good block is 0 image len = 109391872 , image checksum = dd9447db umount: can't umount /usr/local/tmp: Invalid argument dump image checksum=dd9447db mount cmd:busybox mount -t squashfs -o loop /usr/local/tmp/image.cfs /usr/local/modules cp: can't stat '/tmp1/*': No such file or directory ln: /usr/sbin/./transmission-daemon: File exists ln: /usr/sbin/./transmission-remote: File exists ln: /lib/./liblber-2.4.so.2.5.6: File exists ln: /lib/./libminiupnpc.so: File exists ln: /lib/./libnatpmp.so: File exists ln: /lib/./libpam.so.0.81.6: File exists ln: /usr/local/sbin/alert_email_config.sh: File exists ln: /usr/sbin/language.sh: File exists dev.raid.speed_limit_max = 1000 egiga0 Link encap:Ethernet HWaddr 00:50:43:02:02:01 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:532 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:193 egiga2 Link encap:Ethernet HWaddr 00:50:43:02:02:03 egiga0: mac address changed BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:532 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:195 Do Lan Port Switch egiga2: mac address changed not_egiga0: mac address changed jnl: driver (UFSD_HEAD UFSD_HEAD_r244402_b37, LBD=ON) loaded at bf000000 ufsd: module license 'Commercial product' taints kernel. Disabling lock debugging due to kernel taint ufsd:: trace mask set to 0000000f ufsd: driver (UFSD_HEAD UFSD_HEAD_r244402_b37, build_host("swtest6"), acl, ioctl, bdi, sd2(0), fua, bz, tr, rsrc) loaded at bf020000 NTFS support included Hfs+/HfsJ support included optimized: speed Build_for__WD_Yellowstone_k3.10.39_2015-02-12_16T_UFSD_HEAD_r244402_b37 bio: create slab <bio-1> at 1 Btrfs loaded tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> lrwxrwxrwx 1 root 0 17 Jul 6 07:16 /usr/sbin//raid_config -> /usr/sbin/diskmgr lrwxrwxrwx 1 root 0 17 Jul 6 07:16 /usr/sbin//raid_expand -> /usr/sbin/diskmgr lrwxrwxrwx 1 root 0 17 Jul 6 07:16 /usr/sbin//raid_expand_disks -> /usr/sbin/diskmgr lrwxrwxrwx 1 root 0 17 Jul 6 07:16 /usr/sbin//raid_update_info -> /usr/sbin/diskmgr hardware init pool #1: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added egiga1: link up egiga1: started pool #0: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added egiga2: link up egiga2: started mtd check v1.06.06032015 config mtd type is UBIFS device = /usr/local/config Total size = 12384 Kbytes Used size = 276 Kbytes Free size = 12108 Kbytes percentage = 2 /usr/local/config free size is 12398592 ** copy config files *** Copy orion.db from flash **** cp: can't stat '/usr/local/modules/files/fan_temperature.txt': No such file or directory *** symlink onbrd.ini from flash **** ** set loopback interface UBI: attaching mtd6 to ubi1 UBI: scanning is finished UBI: attached mtd6 (name "reserve1", size 10 MiB) to ubi1 UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 UBI: good PEBs: 80, bad PEBs: 0, corrupted PEBs: 0 UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 UBI: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 3272890495 UBI: available PEBs: 30, total reserved PEBs: 50, PEBs reserved for bad PEB handling: 12 UBI device numbeUBI: background thread "ubi_bgt1d" started, PID 3403 r 1, total 80 LEBs (10158080 bytes, 9.7 MiB), available 30 LEBs (3809280 bytes, 3.6 MiB), LEB size 126976 bytes (124.0 KiB) UBIFS: background thread "ubifs_bgt1_0" started, PID 3422 UBIFS: mounted UBI device 1, volume 0, name "reserve" UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS: FS size: 3047424 bytes (2 MiB, 24 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs) UBIFS: reserved for root: 143937 bytes (140 KiB) UBIFS: media format: w4/r0 (latest is w4/r0), UUID 97276231-A8BE-4582-B00E-6E13A8E42CC4, small LPT model UBIFS: un-mount UBI device 1, volume 0 UBIFS: background thread "ubifs_bgt1_0" stops UBI: attaching mtd7 to ubi2 UBI: scanning is finished UBI: attached mtd7 (name "reserve2", size 10 MiB) to ubi2 UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 UBI: good PEBs: 80, bad PEBs: 0, corrupted PEBs: 0 UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1028955252 UBI: available PEBs: 20, total reserved PEBs: 60, PEBs reserved for bad PEB handling: 14 UBI: background thread "ubi_bgt2d" started, PID 3437 UBI device number 2, total 80 LEBs (10158080 bytes, 9.7 MiB), available 20 LEBs (2539520 bytes, 2.4 MiB), LEB size 126976 bytes (124.0 KiB) mknod: /dev/mtd7: File exists UBIFS: background thread "ubifs_bgt2_0" started, PID 3450 UBIFS: mounted UBI device 2, volume 0, name "reserve2" UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS: FS size: 4063232 bytes (3 MiB, 32 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs) UBIFS: reserved for root: 191915 bytes (187 KiB) UBIFS: media format: w4/r0 (latest is w4/r0), UUID FA6CE2D6-E019-4D9D-BB0E-A7959C06E8CF, small LPT model /dev/mtd7 mount ok(ubi) cp: can't stat '/mnt/ubi2/hidden_eccryption': No such file or directory UBIFS: un-mount UBI device 2, volume 0 UBIFS: background thread "ubifs_bgt2_0" stops mac1 = 00:90:A9:E8:2B:9C lan0:ifconfig egiga0 hegiga0: mac address changed w ether 00:90:A9:E8:2B:9C pool #2: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added egiga0: link up egiga0: started set lan0 speed Model ID : GT GT ln: /usr/local/model/web/pages/images/./icon: File exists hidden encryption: 0 Not support chk_sata old firmware ver:2.10.310.1013.2015 new firmware ver:2.10.310.1013.2015 rm: can't remove '/tmp/fix_wd_config': No such file or directory *** execute rc.init.sh awk: /var/run/udhcpc0.pid: No such file or directory udhcpc (v1.20.2) started cat: can't open '/tmp/setip.0': No such file or directory Sending discover... Sending select for 192.168.2.107... Lease of 192.168.2.107 obtained, lease time 86400 deleting routers route: SIOCDELRT: No such process killall: crond: no process killed crond[3661]: crond: crond (busybox 1.20.2) started, log level 8 RTNETLINK answers: Operation not supported RTNETLINK answers: Operation not supported call load_module network Initializing UPnP Sdk with ipaddress = (null) port = 0 UPnP Initialized ipaddress= 192.168.2.107 port = 49152 Specifying the webserver root directory -- /etc/upnp Registering the RootDevice with desc_doc_url: http://192.168.2.107:49152/nasdevicedesc.xml RootDevice Registered Initializing State Table State Table Initialized crond[3718]: crond: crond (busybox 1.20.2) started, log level 8 --2017-07-06 07:16:27-- http://download.wdc.com/nas/WDMyCloudMirror_HDD_Blacklist.xml Resolving download.wdc.com... Initializing UPnP Sdk with ipaddress = (null) port = 0 UPnP Initialized ipaddress= 192.168.2.107 port = 49153 Specifying the webserver root directory -- /etc/upnp Registering the RootDevice with desc_doc_url: http://192.168.2.107:49153/nasdevicedesc.xml RootDevice Registered Initializing State Table State Table Initialized sh: you need to specify whom to kill Advertisements Sent Advertisements Sent 54.187.253.198, 52.24.240.198, 52.35.218.173, ... Connecting to download.wdc.com|54.187.253.198|:80... connected. HTTP request sent, awaiting response... *** Copy CacheVolume data from flash **** *** set Time Zone **** $Usage: apache {start|stop|restart} {web/dav} Thu Jul 6 07:16:28 PDT 2017 *** get Time from rtc and set it into system **** 403 Forbidden 2017-07-06 07:16:28 ERROR 403: Forbidden. rtc: RTC time = 2017/7/6 Thu 7:16:29 Thu Jul 6 00:16:29 PDT 2017 Set Date & time : sntp -K /dev/null -S -r time.windows.com sntp 4.2.8@1.3265 Fri Jan 9 06:42:54 UTC 2015 (8) Module IPC SERVER Version:(1.00.20090706) ads=0 2017-07-06 00:16:29.604437 (+0800) +1.198621 +/- 0.831678 time.windows.com 13.65.245.138 s2 NTP Server connected successfully!!! created mail daemon thread 0 POWER ON DEVICE!! Up_Send_Ctl : Can not find specified command "ErrStatus" mount: mount point /proc/bus/usb does not exist WD hwlib start.............. Starting system message bus Starting wdtms wdtms started PHY_LAN_NUMBER=1 BOND_ENABLE=0 VLAN0_ENABLE=0 VLAN1_ENABLE=0 --2017-07-06 00:16:33-- http://download.wdc.com/apps/WDMyCloudMirrorG2/WDMyCloudMirrorG2.xml Resolving download.wdc.com... I/O warning : failed to load external entity "/var/www/xml/internal_backup.xml" 52.33.117.19, 52.89.214.250, 54.201.207.64, ... Connecting to download.wdc.com|52.33.117.19|:80... /usr/local/modules/script/system_init: line 1062: /mnt/tmp6/ibuki/avahi_tm_serv: not found cat: can't open '/var/run/traceroute_wd.pid': No such file or directory ash: you need to specify whom to kill killall: traceroute: no process killed -------------use hwlib instead of fan_control b c------------- connected. HTTP request sent, awaiting response... 200 OK Length: 47925 (47K) [text/xml] Saving to: '/var/www/xml/app_info.xml' 100%[======================================>] 47,925 136KB/s in 0.3s 2017-07-06 00:16:34 (136 KB/s) - '/var/www/xml/app_info.xml' saved [47925/47925] I/O warning : failed to load external entity "/var/www/xml/app_update.xml" [ERROR] Unable to open (null) EXT2-fs (sda1): warning: mounting unchecked fs, running e2fsck is recommended restart sysinfod... sysinfod: full update begin... sysinfod: disk connected: previous=0xffffffff, now=0x0 --2017-07-06 00:16:35-- http://download.wdc.com/nas/WDMyCloudMirror_HDD_Blacklist.xml Resolving download.wdc.com... 52.24.240.198, 52.35.218.173, 54.201.207.64, ... Connecting to download.wdc.com|52.24.240.198|:80... connected. HTTP request sent, awaiting response... rtc: system time: 2017/7/6 Thu 7:16:35 setRTCTime 403 Forbidden 2017-07-06 00:16:35 ERROR 403: Forbidden. waiting : [10] Failed to restart apache, ret = 1 mcu version 1.06 chk_io v1.04.20141112 I/O warning : failed to load external entity "/var/www/xml/usb_backup.xml" I/O warning : failed to load external entity "/var/www/xml/internal_backup.xml" system daemon v1.04.20141211 Thu Jul 6 00:16:41 PDT 2017 - %W - Communication Manager - startup is disabled, use 'enable' to start process dev.raid.speed_limit_max = 200000 Please press Enter to activate this console. Failed to restart apache, ret = 1 killall: chk_hotplug: no process killed scandisk for power failure now. *ERROR* main(): scandisk [-a] [(null)] sacndisk for power failure(fs_error_count=0) cat: can't open '/var/run/xmldb_sock_scandisk_config.pid': No such file or directory Up_Send_Ctl : Can not find specified command "ErrStatus" call load_module ### create systemfile ### /usr/sbin/load_module: line 541: can't create /sys/block/sdb/queue/read_ahead_kb: nonexistent directory ### sata_reload_application start ### Initializing UPnP Sdk with ipaddress = (null) port = 0 UPnP Initialized ipaddress= 192.168.2.107 port = 49154 Specifying the webserver root directory -- /etc/upnp Registering the RootDevice with desc_doc_url: http://192.168.2.107:49154/nasdevicedesc.xml RootDevice Registered Initializing State Table State Table Initialized Starting atopacctd cannot switch on process accounting: Function not implemented Starting atop system monitor atop atop started *** APKG Daemon is starting ... *** sh: you need to specify whom to kill Rename is FAILE USE 2nd Rename sh: you need to specify whom to kill LOCK itunes.sh Touch itunes tmp file killall: smbd: no process killed sh: you need to specify whom to kill Advertisements Sent Starting wdnotifier wdnotifier started Starting wdmcserver EXT2-fs (sda1): error: ext2_check_page: bad entry in directory #32770: : unaligned directory entry - offset=0, inode=3637925604, rec_len=3034, name_len=134 EXT2-fs (sda1): error: ext2_readdir: bad page in #32770 mt-daapd db path no found ..... UNLOCK itunes.sh Starting wdphotodbmerger WDPhotodbmerger started 0 Thu Jul 6 00:16:53 PDT 2017 /etc/init.d/onbrdnetloccommd - Start killall: smbd: no process killed EXT2-fs (sda1): error: ext2_check_page: bad entry in directory #32769: : unaligned directory entry - offset=0, inode=4136380826, rec_len=42382, name_len=203 EXT2-fs (sda1): error: ext2_readdir: bad page in #32769 killall: chk_blockip: no process killed killall: chk_blockip: no process killed I/O warning : failed to load external entity "/mnt/USB/USB1_a1/.timeMachine.xml" Document parsed unsuccessfully. sysinfod: full update begin... 3911 root 4096 S avahi-daemon: running [WDMyCloudMirror.local] killall: elephantdriveDaemon: no process killed Failed to restart apache, ret = 1 Setting up docker mkdir: can't create directory '/mnt/HD/HD_a2/Nas_Prog/_docker': No such file or directory Loading ipv6 NET: Registered protocol family 10 Loading drivers Loading /usr/local/modules/driver/nf_conntrack.ko nf_conntrack version 0.5.0 (8034 buckets, 32136 max) Loading /usr/local/modules/driver/nf_nat.ko Loading /usr/local/modules/driver/nf_defrag_ipv4.ko Loading /usr/local/modules/driver/nf_conntrack_ipv4.ko Loading /usr/local/modules/driver/nf_nat_ipv4.ko Loading /usr/local/modules/driver/x_tables.ko Loading /usr/local/modules/driver/xt_conntrack.ko Loading /usr/local/modules/driver/xt_addrtype.ko Loading /usr/local/modules/driver/xt_tcpudp.ko Loading /usr/local/modules/driver/xt_nat.ko Loading /usr/local/modules/driver/ipt_MASQUERADE.ko Loading /usr/local/modules/driveip_tables: (C) 2000-2006 Netfilter Core Team r/ip_tables.ko Loading /usr/local/modules/driver/iptable_filter.ko Loading /usr/local/modules/driver/iptable_nat.ko Loading /usr/local/modules/driver/llc.ko Loading /usr/local/modules/driver/stp.ko Loading /usr/local/modules/driver/bridge.ko Bridge firewalling registered Setting up cgroup Get http:///var/run/docker.sock/v1.19/containers/json: dial unix /var/run/docker.sock: no such file or directory. Are you trying to connect to a TLS-enabled daemon without TLS? wdappmgr_auto_start finished modifying wd apps exit code Starting Docker Docker is not setup! Run docker_daemon.sh setup umount: /mnt/HD/HD_a2/Nas_Prog/_docker/devicemapper: not found Total RAM: 514176 KB Creating /sys/fs/cgroup/memory/docker Docker quota: 171392 KB Set memory quota for docker: 175505408 Docker pid 5612 /usr/sbin/docker_daemon.sh: line 194: /var/lib/docker/docker.log: No such file or directory Stopping wdappmgr wdappmgr is already stopped Starting wdappmgr parent exiting! wdappmgr started curl: (7) Couldn't connect to server curl: (7) Couldn't connect to server curl: (7) Couldn't connect to server curl: (7) Couldn't connect to server curl: (7) Couldn't connect to server ### sata_reload_application end ### rm: /shares/Volume_1: is a directory Create USB dev node rm: can't remove '/tmp/disk_uuid': No such file or directory sysinfod: full update begin... sysinfod: inform: all drives status=No Drives. LED_POWER_ON
Re: My Cloud Mirror Gen2 July 06, 2017 02:56AM |
Admin Registered: 13 years ago Posts: 19,094 |
mcmg2
Re: My Cloud Mirror Gen2 July 06, 2017 03:45AM |
94 % [......................................................................] 95 % [......................................................................] 96 % [......................................................................] 97 % [......................................................................] 98 % [......................................................................] 99 % [.........................................] [Type Ctrl-\ + c to quit] __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01_v1.04 (Jul 05 2017 - 16:59:05) Marvell version: 2014_T3.0p6 mvBoardIdIndexGet(boardId) = 1 Board: GrandTeton DB6820 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 1 GiB Map: Code: 0x3fece000:0x3ff95f50 BSS: 0x3ffef254 Stack: 0x3f9cdf20 Heap: 0x3f9ce000:0x3fece000 raise: Signal # 8 caught raise: Signal # 8 caught U-Boot Environment: 0x00000000:0x00080000 (NAND) NAND: ID: daad ,256 MiB MMC: mv_sdh: 0 PCI-e 0: Detected No Link. USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Creating 1 MTD partitions on "nand0": 0x00000f500000-0x00000ff00000 : "mtd=7" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=7" UBI: MTD device size: 10 MiB UBI: number of good PEBs: 80 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 32 UBI: total number of reserved PEBs: 48 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 2/0 UBIFS: mounted UBI device 0, volume 0, name "reserve2" UBIFS: mounted read-only UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs) UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: LZO UBIFS: reserved for root: 200807 bytes (196 KiB) Loading file '/mac_addr' to addr 0x02000000 with size 18 (0x00000012)... Done Set lan 2 WakeOnLan ok Enable HD1 Enable HD2 Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | In-Band | | egiga1 | RGMII | In-Band | | egiga2 | SGMII | 0x00 | egiga0, egiga1, egiga2 [PRIME] Hit any key to stop autoboot: 0 Marvell>> setenv bootdev usb Marvell>> setenv device '0:1' Marvell>> setenv dtb_file '/boot/dts/armada-385-wd-mcmg2.dtb' Marvell>> setenv load_dtb_addr 0x1000000 Marvell>> setenv load_initrd_addr 0x2900000 Marvell>> setenv load_image_addr 0x02000000 Marvell>> setenv load_dtb 'echo loading DTB $dtb_file ...; ext2load $bootdev $device $load_dtb_addr $dtb_file' Marvell>> setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' Marvell>> setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/zImage' Marvell>> setenv usb_set_bootargs 'setenv bootargs "console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $mtdparts earlyprintk=serial"' Marvell>> setenv usb_set_bootargs 'setenv bootargs "console=ttyS0,115200 root=/dsetenv usb_set_bootargs 'setenv bootargs "console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $mtdparts earlyprintk=serial"' Marvell>> setenv usb_set_bootargs 'setenv bootargs "console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $mtdparts earlyprintk=serial"' Marvell>> setenv usb_bootcmd 'echo Booting from USB ...; setenv fdt_skip_update yes; usb start; run load_image; run load_dtb; run usb_set_bootargs; bootz $load_image_addr - $load_dtb_addr' Marvell>> setenv bootcmd_usb 'usb start; run usb_set_bootargs; run usb_bootcmd; reset' Marvell>> printenv CASset=max MALLOC_len=5 MPmode=SMP autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=root=/dev/ram console=ttyS0,115200 bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=nand read.e 0xa00000 0x500000 0x500000;nand read.e 0xf00000 0xa00000 0x500000;bootm 0xa00000 0xf00000 bootcmd_auto=stage_boot $boot_order bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootcmd_usb=usb start; run usb_set_bootargs; run usb_bootcmd; reset bootdelay=1 bootdev=usb cacheShare=no console=console=ttyS0,115200 device=0:1 device_partition=0:1 disaMvPnp=no dtb_file=/boot/dts/armada-385-wd-mcmg2.dtb eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:1a:29:2c eth1mtu=1500 eth2addr=00:50:43:1a:3c:2c eth2mtu=1500 eth3addr=00:50:43:29:3c:1a eth3mtu=1500 ethact=egiga2 ethaddr=00:50:43:3c:29:2c ethmtu=1500 ethprime=egiga2 fdt_addr=2040000 fdt_skip_update=no fdtaddr=0x1000000 fdtfile=armada-38x-modular.dtb filesize=12 ide_path=/ image_name=uImage initrd_name=uInitrd ipaddr=192.168.11.110 kernel_addr_r=2080000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 load_dtb=echo loading DTB $dtb_file ...; ext2load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1000000 load_image=echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/zImage load_image_addr=0x02000000 load_initrd=echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x2900000 loadaddr=0x02000000 loads_echo=0 mtddevname=u-boot mtddevnum=0 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:2c:3c:1a nandEcc=nfcConfig=4bitecc netbsd_en=no netmask=255.255.255.0 netretry=no partition=nand0,0 pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rootpath=/srv/nfs/ sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scr serverip=192.168.11.114 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usbActive=0 usbType=3 usb_bootcmd=echo Booting from USB ...; setenv fdt_skip_update yes; usb start; run load_image; run load_dtb; run usb_set_bootargs; bootz $load_image_addr - $load_dtb_addr usb_set_bootargs=setenv bootargs "console=ttyS0,115200 root=/dev/sda1 rootdelay=10 $mtdparts earlyprintk=serial" vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 4008/524284 bytes Marvell>> run bootcmd_usb (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Booting from USB ... (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found loading Image ... ** Bad device usb 0 ** loading DTB /boot/dts/armada-385-wd-mcmg2.dtb ... ** Bad device usb 0 ** Bad Linux ARM zImage magic! resetting ... BootROM - 1.73 Booting from NAND flash General initialization - Version: 1.0.0 Detected Device ID 6820 High speed PHY - Version: 2.0 Load WD GrandTeton Serdes Config: board SerDes lanes topology details: | Lane # | Speed | Type | -------------------------------- | 0 | 06 | SATA0 | | 1 | 05 | PCIe0 | | 2 | 06 | SATA1 | | 3 | 05 | USB3 HOST1 | | 4 | 05 | USB3 HOST0 | | 5 | 00 | SGMII2 | -------------------------------- PCIe, Idx 0: detected no link High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.26.0 mvSysEnvGetTopologyUpdateInfo: TWSI Read failed DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01_v1.02 (Jun 25 2015 - 17:06:32) Marvell version: 2014_T3.0p6 mvBoardIdIndexGet(boardId) = 1 Board: GrandTeton DB6820 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB Map: Code: 0x1fece000:0x1ff95bd4 BSS: 0x1ffef254 Stack: 0x1f9cdf20 Heap: 0x1f9ce000:0x1fece000 raise: Signal # 8 caught raise: Signal # 8 caught U-Boot Environment: 0x00000000:0x00080000 (NAND) NAND: mvNfcInit mvNfcReset() ret = 0x0 read Nand Flash ID ID: daad ,nand reg = 0x.8ff8166 256 MiB MMC: mv_sdh: 0 PCI-e 0: Detected No Link. USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Creating 1 MTD partitions on "nand0": 0x00000f500000-0x00000ff00000 : "mtd=7" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=7" UBI: MTD device size: 10 MiB UBI: number of good PEBs: 80 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 32 UBI: total number of reserved PEBs: 48 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 2/0 UBIFS: mounted UBI device 0, volume 0, name "reserve2" UBIFS: mounted read-only UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs) UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: LZO UBIFS: reserved for root: 200807 bytes (196 KiB) Loading file '/mac_addr' to addr 0x02000000 with size 18 (0x00000012)... Done Set lan 2 WakeOnLan ok Enable HD1 Enable HD2 Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | In-Band | | egiga1 | RGMII | In-Band | | egiga2 | SGMII | 0x00 | egiga0, egiga1, egiga2 [PRIME] Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x500000, size 0x500000 5242880 bytes read: OK NAND read: device 0 offset 0xa00000, size 0x500000 5242880 bytes read: OK ## Booting image at 00a00000 ... ## Booting kernel from Legacy Image at 00a00000 ... Image Name: Linux-382 Created: 2015-08-02 3:54:03 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4093292 Bytes = 3.9 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 00f00000 ... Image Name: Ramdisk Created: 2015-10-13 10:23:23 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 2278194 Bytes = 2.2 MiB Load Address: 00e00000 Entry Point: 00e00000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Initializing cgroup subsys cpuset Initializing cgroup subsys cpu Initializing cgroup subsys cpuacct Linux version 3.10.39 (kman@kmachine) (gcc version 4.6.4 (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPAGESIZE ALIGN) ) #1 SMP Sun Aug 2 11:53:57 CST 2015 2014T30p5 Build-git3e9fe59 CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: Marvell Armada 380/381/382/385/388 (Device Tree), model: Marvell Armada 385 Development Board Memory policy: ECC disabled, Data cache writealloc PERCPU: Embedded 1 pages/cpu @c0930000 s8320 r8192 d16256 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16364 Kernel command line: root=/dev/ram console=ttyS0,115200 PID hash table entries: 2048 (order: -2, 8192 bytes) Dentry cache hash table entries: 65536 (order: 3, 262144 bytes) Inode-cache hash table entries: 32768 (order: 2, 131072 bytes) allocated 131072 bytes of page_cgroup please try 'cgroup_disable=memory' option if you don't want memory cgroups Memory: 512MB = 512MB total Memory: 511744k/511744k available, 12544k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff8000 ( 32 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xe0800000 - 0xfff00000 ( 503 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc0714278 (7217 kB) .init : 0xc0718000 - 0xc075a080 ( 265 kB) .data : 0xc075c000 - 0xc07a7e40 ( 304 kB) .bss : 0xc07a7e40 - 0xc0871570 ( 806 kB) Hierarchical RCU implementation. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. NR_IRQS:16 nr_irqs:16 16 LSP version: linux-3.10.39-2014_T3.0p5 sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms L310 cache controller enabled l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B Console: colour dummy device 80x30 Calibrating delay loop... 2655.84 BogoMIPS (lpj=13279232) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 4096 Initializing cgroup subsys memory Initializing cgroup subsys devices Initializing cgroup subsys freezer Initializing cgroup subsys blkio CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0xc056c2b0 - 0xc056c308 mvebu-pmsu: Initializing Power Management Service Unit Initializing CPU Reset module CPU1: Booted secondary processor CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 Brought up 2 CPUs SMP: Total of 2 processors activated (5311.69 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4 xor: measuring software checksum speed arm4regs : 1424.000 MB/sec 8regs : 940.800 MB/sec 32regs : 921.600 MB/sec xor: using function: arm4regs (1424.000 MB/sec) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations irq: Cannot allocate irq_descs @ IRQ196, assuming pre-allocated irq: Cannot allocate irq_descs @ IRQ228, assuming pre-allocated bio: create slab <bio-0> at 0 raid6: int32x1 355 MB/s raid6: int32x2 347 MB/s raid6: int32x4 446 MB/s raid6: int32x8 384 MB/s raid6: using algorithm int32x4 (446 MB/s) raid6: using intx1 recovery algorithm mvebu-pcie pcie-controller.3: PCIe0.0: link down mvebu-pcie pcie-controller.3: PCIe1.0: link down mvebu-pcie pcie-controller.3: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe8000000] pci_bus 0000:00: root bus resource [bus 00-ff] PCI: bus0: Fast back to back transfers disabled pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring PCI: bus1: Fast back to back transfers enabled PCI: bus2: Fast back to back transfers enabled pci 0000:00:01.0: PCI bridge to [bus 01] pci 0000:00:02.0: PCI bridge to [bus 02] PCI: enabling device 0000:00:01.0 (0140 -> 0143) PCI: enabling device 0000:00:02.0 (0140 -> 0143) SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> PTP clock support registered Switching to clocksource armada_370_xp_clocksource NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 0, 32768 bytes) TCP bind hash table entries: 4096 (order: 0, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP: reno registered UDP hash table entries: 1024 (order: 0, 32768 bytes) UDP-Lite hash table entries: 1024 (order: 0, 32768 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Trying to unpack rootfs image as initramfs... rootfs image is not initramfs (no cpio magic); looks like an initrd Freeing initrd memory: 2176K (c0f08000 - c1128000) VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 8192 (order 0, 32768 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher Installing knfsd (copyright (C) 1996 okir@monad.swb.de). fuse init (API version 7.22) SGI XFS with security attributes, large block/inode numbers, no debug enabled msgmni has been set to 1002 async_tx: api initialized (async) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver mv_xor f1060800.xor: Marvell shared XOR driver mv_xor f1060800.xor: Marvell XOR: ( xor cpy intr ) mv_xor f1060800.xor: freeing 1 in use descriptors! mv_xor f1060800.xor: Marvell XOR: ( crc32c ) mv_xor f1060900.xor: Marvell shared XOR driver mv_xor f1060900.xor: Marvell XOR: ( xor cpy intr ) mv_xor f1060900.xor: freeing 1 in use descriptors! mv_xor f1060900.xor: Marvell XOR: ( crc32c ) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A console [ttyS0] enabled f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 45) is a 16550A brd: module loaded loop: module loaded ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs scsi0 : ahci_mv_platform scsi1 : ahci_mv_platform ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58 ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58 armada-nand f10d0000.nand: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC Nand Flash Timing = [WP : 12], [WH : 10] NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix NAND 256MiB 3,3V 8-bit), 256MiB, page size: 2048, OOB size: 64 Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 8 ofpart partitions found on MTD device armada-nand Creating 8 MTD partitions on "armada-nand": 0x000000000000-0x000000500000 : "U-Boot" 0x000000500000-0x000000a00000 : "uImage" 0x000000a00000-0x000000f00000 : "uRamdisk" 0x000000f00000-0x00000c800000 : "image.cfs" 0x00000c800000-0x00000d700000 : "rescue fw" 0x00000d700000-0x00000eb00000 : "config" 0x00000eb00000-0x00000f500000 : "reserve1" 0x00000f500000-0x00000ff00000 : "reserve2" SoC: model = 0x6820, revision = 0x4 mvPncVirtBase = 0xe0e00000, pncTcamSize = 1024 o 3 Giga ports supported o SKB recycle supported (Disabled) o NETA acceleration mode 4 o BM supported for CPU: 4 BM pools o PnC supported (Enabled) o RX Queue support: 8 Queues * 256 Descriptors o TX Queue support: 8 Queues * 532 Descriptors o GSO supported o GRO supported o Receive checksum offload supported o Transmit checksum offload supported o Driver ERROR statistics enabled o Driver INFO statistics enabled o Driver DEBUG statistics enabled port #0: is_sgmii=0, is_rgmii=1, phy_addr=2 o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800 o Port 0 is connected to Linux netdevice o egiga0, ifindex = 2, GbE port = 0 giga p=0: mtu=1500, mac=00:50:43:02:02:01 (platform) port #1: is_sgmii=0, is_rgmii=1, phy_addr=1 o Loading network interface(s) for port #1: cpu_mask=0x3, tx_csum_limit=2048 o Port 1 is connected to Linux netdevice o egiga1, ifindex = 3, GbE port = 1 giga p=1: mtu=1500, mac=00:50:43:02:02:02 (platform) port #2: is_sgmii=1, is_rgmii=0, phy_addr=0 o Loading network interface(s) for port #2: cpu_mask=0x3, tx_csum_limit=2048 o Port 2 is connected to Linux netdevice o egiga2, ifindex = 4, GbE port = 2 giga p=2: mtu=1500, mac=00:50:43:02:02:03 (platform) libphy: orion_mdio_bus: probed mdio_bus f1072004.mdio-mi: cannot get PHY at address 2 mdio_bus f1072004.mdio-mi: cannot get PHY at address 1 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-orion: EHCI orion driver orion-ehci f1058000.usb: EHCI Host Controller orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 orion-ehci f1058000.usb: irq 50, io mem 0xf1058000 orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000 hub 4-0:1.0: USB hub found hub 4-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller ata1: SATA link down (SStatus 0 SControl 300) ata2: SATA link down (SStatus 0 SControl 300) xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 hub 5-0:1.0: USB hub found hub 5-0:1.0: 1 port detected usbcore: registered new interface driver usb-storage usb 4-1: new high-speed USB device number 2 using xhci-hcd usb 4-1: ep 0x81 - rounding interval to 128 microframes, ep desc says 255 microframes usb 4-1: ep 0x2 - rounding interval to 128 microframes, ep desc says 255 microframes usb-storage 4-1:1.0: USB Mass Storage device detected scsi2 : usb-storage 4-1:1.0 mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 i2c /dev entries driver md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com dm_crypt using the OCF package. cpuidle: using governor ladder armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2 armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: chain(0) mvCesaInit: channels=2, session=640, queue=256 armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode cesadev_init(c0734f0c) TCP: cubic registered NET: Registered protocol family 17 8021q: 802.1Q VLAN Support v1.8 VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 registered taskstats version 1 mvebu-rtc f10a3800.rtc: setting system clock to 2017-07-06 08:42:43 UTC (1499330563) md: Waiting for all devices to be available before autodetect md: If you don't use raid, use raid=noautodetect md: Autodetecting RAID arrays. md: Scanned 0 and added 0 devices. md: autorun ... md: ... autorun DONE. RAMDISK: gzip image found at block 0 VFS: Mounted root (ext2 filesystem) readonly on device 1:0. devtmpfs: mounted Freeing unused kernel memory: 256K (c0718000 - c0758000) init started: BusyBox v1.20.2 (2014-10-30 15:28:59 CST) starting pid 1261, tty '': '/etc/rc.sh' ** Mounting /etc/fstab umount: can't umount /proc: Invalid argument umount: can't umount /usr/local/modules: Invalid argument scsi 2:0:0:0: Direct-Access SRT POLLEX 8G 1100 PQ: 0 ANSI: 4 sd 2:0:0:0: Attached scsi generic sg0 type 0 sd 2:0:0:0: [sda] 15728640 512-byte logical blocks: (8.05 GB/7.50 GiB) sd 2:0:0:0: [sda] Write Protect is off sd 2:0:0:0: [sda] No Caching mode page found sd 2:0:0:0: [sda] Assuming drive cache: write through sd 2:0:0:0: [sda] No Caching mode page found sd 2:0:0:0: [sda] Assuming drive cache: write through sda: sda1 sd 2:0:0:0: [sda] No Caching mode page found sd 2:0:0:0: [sda] Assuming drive cache: write through sd 2:0:0:0: [sda] Attached SCSI removable disk sh: hotPlug.sh: not found offset_flag=1,vaule_flag=1,bit_flag=0 offset_flag=1,vaule_flag=1,bit_flag=0 offset_flag=1,vaulUBI: attaching mtd5 to ubi0 e_flag=1,bit_flag=0 offset_flag=1,vaule_flag=1,bit_flag=0 UBI: scanning is finished UBI: attached mtd5 (name "config", size 20 MiB) to ubi0 UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 UBI: good PEBs: 160, bad PEBs: 0, corrupted PEBs: 0 UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 UBI: max/mean erase counter: 11/6, WL threshold: 4096, image sequence number: 1847991382 UBI: available PEBs: 22, total reserved PEBs: 138, PEBs reserved for bad PEB handling: 10 UBI: background thread "ubi_bgt0d" started, PID 1292 UBI device number 0, total 160 LEBs (20316160 bytes, 19.4 MiB), available 22 LEBs (2793472 bytes, 2.7 MiB), LEB size 126976 bytes (124.0 KiB) UBIFS: background thread "ubifs_bgt0_0" started, PID 1297 UBIFS: recovery needed UBIFS: recovery completed UBIFS: mounted UBI device 0, volume 0, name "config" UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS: FS size: 14475264 bytes (13 MiB, 114 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs) UBIFS: reserved for root: 683702 bytes (667 KiB) UBIFS: media format: w4/r0 (latest is w4/r0), UUID 12CDA789-300F-44B7-B437-4B5666A1DA39, small LPT model umount: can't umount /usr/local/tmp/image.cfs: No such file or directory rm: can't remove '/usr/local/tmp/image.cfs': No such file or directory umount: can't umount /usr/local/tmp: Invalid argument first good block is 0 image len = 109391872 , image checksum = dd9447db umount: can't umount /usr/local/tmp: Invalid argument dump image checksum=dd9447db mount cmd:busybox mount -t squashfs -o loop /usr/local/tmp/image.cfs /usr/local/modules cp: can't stat '/tmp1/*': No such file or directory ln: /usr/sbin/./transmission-daemon: File exists ln: /usr/sbin/./transmission-remote: File exists ln: /lib/./liblber-2.4.so.2.5.6: File exists ln: /lib/./libminiupnpc.so: File exists ln: /lib/./libnatpmp.so: File exists ln: /lib/./libpam.so.0.81.6: File exists ln: /usr/local/sbin/alert_email_config.sh: File exists ln: /usr/sbin/language.sh: File exists dev.raid.speed_limit_max = 1000 egiga0 Link encap:Ethernet HWaddr 00:50:43:02:02:01 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:532 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:193 egiga2 Link encap:Ethernet HWaddr 00:50:43:02:02:03 BROADCASTegiga0: mac address changed MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:532 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:195 Do Lan Port Switch egiga2: mac address changed not_egiga0: mac address changed jnl: driver (UFSD_HEAD UFSD_HEAD_r244402_b37, LBD=ON) loaded at bf000000 ufsd: module license 'Commercial product' taints kernel. Disabling lock debugging due to kernel taint ufsd:: trace mask set to 0000000f ufsd: driver (UFSD_HEAD UFSD_HEAD_r244402_b37, build_host("swtest6"), acl, ioctl, bdi, sd2(0), fua, bz, tr, rsrc) loaded at bf020000 NTFS support included Hfs+/HfsJ support included optimized: speed Build_for__WD_Yellowstone_k3.10.39_2015-02-12_16T_UFSD_HEAD_r244402_b37 bio: create slab <bio-1> at 1 Btrfs loaded tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> lrwxrwxrwx 1 root 0 17 Jul 6 08:43 /usr/sbin//raid_config -> /usr/sbin/diskmgr lrwxrwxrwx 1 root 0 17 Jul 6 08:43 /usr/sbin//raid_expand -> /usr/sbin/diskmgr lrwxrwxrwx 1 root 0 17 Jul 6 08:43 /usr/sbin//raid_expand_disks -> /usr/sbin/diskmgr lrwxrwxrwx 1 root 0 17 Jul 6 08:43 /usr/sbin//raid_update_info -> /usr/sbin/diskmgr hardware init pool #1: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added egiga1: link up egiga1: started pool #0: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added egiga2: link up egiga2: started mtd check v1.06.06032015 config mtd type is UBIFS device = /usr/local/config Total size = 12384 Kbytes Used size = 276 Kbytes Free size = 12108 Kbytes percentage = 2 /usr/local/config free size is 12398592 ** copy config files *** Copy orion.db from flash **** cp: can't stat '/usr/local/modules/files/fan_temperature.txt': No such file or directory *** symlink onbrd.ini from flash **** ** set loopback interface UBI: attaching mtd6 to ubi1 UBI: scanning is finished UBI: attached mtd6 (name "reserve1", size 10 MiB) to ubi1 UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 UBI: good PEBs: 80, bad PEBs: 0, corrupted PEBs: 0 UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 UBI: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 3272890495 UBI: available PEBs: 30, total reserved PEBs: 50, PEBs reserved for bad PEB handling: 12 UBI device numbeUBI: background thread "ubi_bgt1d" started, PID 3402 r 1, total 80 LEBs (10158080 bytes, 9.7 MiB), available 30 LEBs (3809280 bytes, 3.6 MiB), LEB size 126976 bytes (124.0 KiB) UBIFS: background thread "ubifs_bgt1_0" started, PID 3420 UBIFS: mounted UBI device 1, volume 0, name "reserve" UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS: FS size: 3047424 bytes (2 MiB, 24 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs) UBIFS: reserved for root: 143937 bytes (140 KiB) UBIFS: media format: w4/r0 (latest is w4/r0), UUID 97276231-A8BE-4582-B00E-6E13A8E42CC4, small LPT model UBIFS: un-mount UBI device 1, volume 0 UBIFS: background thread "ubifs_bgt1_0" stops UBI: attaching mtd7 to ubi2 UBI: scanning is finished UBI: attached mtd7 (name "reserve2", size 10 MiB) to ubi2 UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 UBI: good PEBs: 80, bad PEBs: 0, corrupted PEBs: 0 UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1028955252 UBI: available PEBs: 20, total reserved PEBs: 60, PEBs reserved for bad PEB handling: 14 UBI: background thread "ubi_bgt2d" started, PID 3435 UBI device number 2, total 80 LEBs (10158080 bytes, 9.7 MiB), available 20 LEBs (2539520 bytes, 2.4 MiB), LEB size 126976 bytes (124.0 KiB) mknod: /dev/mtd7: File exists UBIFS: background thread "ubifs_bgt2_0" started, PID 3448 UBIFS: mounted UBI device 2, volume 0, name "reserve2" UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS: FS size: 4063232 bytes (3 MiB, 32 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs) UBIFS: reserved for root: 191915 bytes (187 KiB) UBIFS: media format: w4/r0 (latest is w4/r0), UUID FA6CE2D6-E019-4D9D-BB0E-A7959C06E8CF, small LPT model /dev/mtd7 mount ok(ubi) cp: can't stat '/mnt/ubi2/hidden_eccryption': No such file or directory UBIFS: un-mount UBI device 2, volume 0 UBIFS: background thread "ubifs_bgt2_0" stops mac1 = 00:90:A9:E8:2B:9C lan0:ifconfig egiga0 hegiga0: mac address changed w ether 00:90:A9:E8:2B:9C pool #2: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added egiga0: link up egiga0: started set lan0 speed Model ID : GT GT ln: /usr/local/model/web/pages/images/./icon: File exists hidden encryption: 0 Not support chk_sata old firmware ver:2.10.310.1013.2015 new firmware ver:2.10.310.1013.2015 rm: can't remove '/tmp/fix_wd_config': No such file or directory *** execute rc.init.sh awk: /var/run/udhcpc0.pid: No such file or directory udhcpc (v1.20.2) started cat: can't open '/tmp/setip.0': No such file or directory Sending discover... Sending select for 192.168.2.107... Lease of 192.168.2.107 obtained, lease time 86400 deleting routers route: SIOCDELRT: No such process killall: crond: no process killed crond[3659]: crond: crond (busybox 1.20.2) started, log level 8 RTNETLINK answers: Operation not supported RTNETLINK answers: Operation not supported call load_module network Initializing UPnP Sdk with ipaddress = (null) port = 0 UPnP Initialized ipaddress= 192.168.2.107 port = 49152 Specifying the webserver root directory -- /etc/upnp Registering the RootDevice with desc_doc_url: http://192.168.2.107:49152/nasdevicedesc.xml RootDevice Registered Initializing State Table State Table Initialized crond[3716]: crond: crond (busybox 1.20.2) started, log level 8 --2017-07-06 08:43:14-- http://download.wdc.com/nas/WDMyCloudMirror_HDD_Blacklist.xml Resolving download.wdc.com... Initializing UPnP Sdk with ipaddress = (null) port = 0 UPnP Initialized ipaddress= 192.168.2.107 port = 49153 Specifying the webserver root directory -- /etc/upnp Registering the RootDevice with desc_doc_url: http://192.168.2.107:49153/nasdevicedesc.xml RootDevice Registered Initializing State Table State Table Initialized sh: you need to specify whom to kill Advertisements Sent 52.89.214.250, 52.33.117.19, 52.35.218.173, ... Connecting to download.wdc.com|52.89.214.250|:80... Advertisements Sent connected. HTTP request sent, awaiting response... 403 Forbidden 2017-07-06 08:43:15 ERROR 403: Forbidden. *** Copy CacheVolume data from flash **** *** set Time Zone **** $Usage: apache {start|stop|restart} {web/dav} Thu Jul 6 08:43:15 PDT 2017 *** get Time from rtc and set it into system **** rtc: RTC time = 2017/7/6 Thu 8:43:16 Thu Jul 6 01:43:16 PDT 2017 Set Date & time : sntp -K /dev/null -S -r time.windows.com sntp 4.2.8@1.3265 Fri Jan 9 06:42:54 UTC 2015 (8) Module IPC SERVER Version:(1.00.20090706) ads=0 2017-07-06 01:43:16.619784 (+0800) +1.409759 +/- 0.974237 time.windows.com 13.65.245.138 s2 NTP Server connected successfully!!! created mail daemon thread 0 POWER ON DEVICE!! Up_Send_Ctl : Can not find specified command "ErrStatus" mount: mount point /proc/bus/usb does not exist WD hwlib start.............. Starting system message bus Starting wdtms PHY_LAN_NUMBER=1 wdtms started BOND_ENABLE=0 VLAN0_ENABLE=0 VLAN1_ENABLE=0 --2017-07-06 01:43:20-- http://download.wdc.com/apps/WDMyCloudMirrorG2/WDMyCloudMirrorG2.xml Resolving download.wdc.com... I/O warning : failed to load external entity "/var/www/xml/internal_backup.xml" 54.187.253.198, 54.201.207.64, 52.24.240.198, ... Connecting to download.wdc.com|54.187.253.198|:80... /usr/local/modules/script/system_init: line 1062: /mnt/tmp6/ibuki/avahi_tm_serv: not found cat: can't open '/var/run/traceroute_wd.pid': No such file or directory ash: you need to specify whom to kill killall: traceroute: no process killed -------------use hwlib instead of fan_control b c------------- connected. HTTP request sent, awaiting response... 200 OK Length: 47925 (47K) [text/xml] Saving to: '/var/www/xml/app_info.xml' 100%[======================================>] 47,925 90.0KB/s in 0.5s 2017-07-06 01:43:21 (90.0 KB/s) - '/var/www/xml/app_info.xml' saved [47925/47925] I/O warning : failed to load external entity "/var/www/xml/app_update.xml" [ERROR] Unable to open (null) EXT2-fs (sda1): warning: mounting unchecked fs, running e2fsck is recommended restart sysinfod... sysinfod: full update begin... sysinfod: disk connected: previous=0xffffffff, now=0x0 --2017-07-06 01:43:22-- http://download.wdc.com/nas/WDMyCloudMirror_HDD_Blacklist.xml Resolving download.wdc.com... 52.33.117.19, 52.35.218.173, 52.24.240.198, ... Connecting to download.wdc.com|52.33.117.19|:80... connected. HTTP request sent, awaiting response... rtc: system time: 2017/7/6 Thu 8:43:22 setRTCTime 403 Forbidden 2017-07-06 01:43:22 ERROR 403: Forbidden. waiting : [10] Failed to restart apache, ret = 1 mcu version 1.06 chk_io v1.04.20141112 I/O warning : failed to load external entity "/var/www/xml/usb_backup.xml" system daemon v1.04.20141211 I/O warning : failed to load external entity "/var/www/xml/internal_backup.xml" Thu Jul 6 01:43:28 PDT 2017 - %W - Communication Manager - startup is disabled, use 'enable' to start process dev.raid.speed_limit_max = 200000 Please press Enter to activate this console. Failed to restart apache, ret = 1 killall: chk_hotplug: no process killed scandisk for power failure now. *ERROR* main(): scandisk [-a] [(null)] sacndisk for power failure(fs_error_count=0) cat: can't open '/var/run/xmldb_sock_scandisk_config.pid': No such file or directory Up_Send_Ctl : Can not find specified command "ErrStatus" call load_module ### create systemfile ### /usr/sbin/load_module: line 541: can't create /sys/block/sdb/queue/read_ahead_kb: nonexistent directory ### sata_reload_application start ### Initializing UPnP Sdk with ipaddress = (null) port = 0 Starting atopacctd UPnP Initialized ipaddress= 192.168.2.107 port = 49154 Specifying the webserver root directory -- /etc/upnp Registering the RootDevice with desc_doc_url: http://192.168.2.107:49154/nasdevicedesc.xml RootDevice Registered Initializing State Table State Table Initialized cannot switch on process accounting: Function not implemented Starting atop system monitor atop atop started *** APKG Daemon is starting ... *** sh: you need to specify whom to kill sh: you need to specify whom to kill killall: smbd: no process killed Starting wdnotifier Rename is FAILE USE 2nd Rename LOCK itunes.sh Touch itunes tmp file sh: you need to specify whom to kill Advertisements Sent wdnotifier started Starting wdmcserver mt-daapd db path no found ..... UNLOCK itunes.sh Starting wdphotodbmerger WDPhotodbmerger started 0 Thu Jul 6 01:43:40 PDT 2017 /etc/init.d/onbrdnetloccommd - Start killall: smbd: no process killed killall: chk_blockip: no process killed killall: chk_blockip: no process killed Failed to restart apache, ret = 1 I/O warning : failed to load external entity "/mnt/USB/USB1_a1/.timeMachine.xml" Document parsed unsuccessfully. sysinfod: full update begin... 3909 root 4224 S avahi-daemon: running [WDMyCloudMirror.local] killall: elephantdriveDaemon: no process killed Setting up docker mkdir: can't create directory '/mnt/HD/HD_a2/Nas_Prog/_docker': No such file or directory Loading ipv6 NET: Registered protocol family 10 Loading drivers Loading /usr/local/modules/driver/nf_conntrack.ko nf_conntrack version 0.5.0 (8034 buckets, 32136 max) Loading /usr/local/modules/driver/nf_nat.ko Loading /usr/local/modules/driver/nf_defrag_ipv4.ko Loading /usr/local/modules/driver/nf_conntrack_ipv4.ko Loading /usr/local/modules/driver/nf_nat_ipv4.ko Loading /usr/local/modules/driver/x_tables.ko Loading /usr/local/modules/driver/xt_conntrack.ko Loading /usr/local/modules/driver/xt_addrtype.ko Loading /usr/local/modules/driver/xt_tcpudp.ko Loading /usr/local/modules/driver/xt_nat.ko Loading /usr/local/modules/driver/ipt_MASQUERADE.ko Loading /usr/local/modules/driveip_tables: (C) 2000-2006 Netfilter Core Team r/ip_tables.ko Loading /usr/local/modules/driver/iptable_filter.ko Loading /usr/local/modules/driver/iptable_nat.ko Loading /usr/local/modules/driver/llc.ko Loading /usr/local/modules/driver/stp.ko Loading /usr/local/modules/driver/bridge.ko Bridge firewalling registered Setting up cgroup Get http:///var/run/docker.sock/v1.19/containers/json: dial unix /var/run/docker.sock: no such file or directory. Are you trying to connect to a TLS-enabled daemon without TLS? wdappmgr_auto_start finished modifying wd apps exit code Starting Docker Docker is not setup! Run docker_daemon.sh setup umount: /mnt/HD/HD_a2/Nas_Prog/_docker/devicemapper: not found Total RAM: 514176 KB Creating /sys/fs/cgroup/memory/docker Docker quota: 171392 KB Set memory quota for docker: 175505408 /usr/sbin/docker_daemon.sh: line 194: /var/lib/docker/docker.log: No such file or directory Docker pid 5647 Stopping wdappmgr wdappmgr is already stopped Starting wdappmgr parent exiting! wdappmgr started curl: (7) Couldn't connect to server curl: (7) Couldn't connect to server curl: (7) Couldn't connect to server curl: (7) Couldn't connect to server curl: (7) Couldn't connect to server ### sata_reload_application end ### rm: /shares/Volume_1: is a directory Create USB dev node rm: can't remove '/tmp/disk_uuid': No such file or directory sysinfod: full update begin... sysinfod: inform: all drives status=No Drives. LED_POWER_ON
Re: My Cloud Mirror Gen2 July 06, 2017 04:48AM |
Admin Registered: 13 years ago Posts: 19,094 |
cd /media/sdb1/boot cp -a zImage-4.9.0-mvebu-tld-12 zImage.fdt cat dts/armada-385-wd-mcmg2.dtb >> zImage.fdt mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-4.9.0-mvebu-tld-12 -d zImage.fdt uImage
setenv bootdev 'usb' setenv device '0:1' setenv load_image_addr '0x02000000' setenv load_initrd_addr '0x2900000' setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage' setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' setenv bootcmd_usb 'echo Booting from USB ...; usb start; setenv fdt_skip_update yes; usb start; run usb_set_bootargs; if run load_image; then if run load_initrd; then bootm $load_image_addr $load_initrd_addr; else bootm $load_image_addr; fi; fi' run bootcmd_usb
Re: My Cloud Mirror Gen2 July 06, 2017 09:10AM |
Registered: 7 years ago Posts: 119 |
Quote
bodhi
On this WD Mirror Gen 2, you need to boot the same way as the WD My Cloud EX4100.
(Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Booting from USB ...
scsi 2:0:0:0: Direct-Access SRT POLLEX 8G 1100 PQ: 0 ANSI: 4 sd 2:0:0:0: Attached scsi generic sg0 type 0 sd 2:0:0:0: [sda] 15728640 512-byte logical blocks: (8.05 GB/7.50 GiB) sd 2:0:0:0: [sda] Write Protect is off sd 2:0:0:0: [sda] No Caching mode page found sd 2:0:0:0: [sda] Assuming drive cache: write through sd 2:0:0:0: [sda] No Caching mode page found sd 2:0:0:0: [sda] Assuming drive cache: write through sda: sda1 sd 2:0:0:0: [sda] No Caching mode page found sd 2:0:0:0: [sda] Assuming drive cache: write through sd 2:0:0:0: [sda] Attached SCSI removable disk ... EXT2-fs (sda1): warning: mounting unchecked fs, running e2fsck is recommended
mcmg2
Re: My Cloud Mirror Gen2 July 06, 2017 04:01PM |
98 % [......................................................................] 99 % [.........................................] [Type Ctrl-\ + c to quit] __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01_v1.04 (Jul 05 2017 - 16:59:05) Marvell version: 2014_T3.0p6 mvBoardIdIndexGet(boardId) = 1 Board: GrandTeton DB6820 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 1 GiB Map: Code: 0x3fece000:0x3ff95f50 BSS: 0x3ffef254 Stack: 0x3f9cdf20 Heap: 0x3f9ce000:0x3fece000 raise: Signal # 8 caught raise: Signal # 8 caught U-Boot Environment: 0x00000000:0x00080000 (NAND) NAND: ID: daad ,256 MiB MMC: mv_sdh: 0 PCI-e 0: Detected No Link. USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Creating 1 MTD partitions on "nand0": 0x00000f500000-0x00000ff00000 : "mtd=7" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=7" UBI: MTD device size: 10 MiB UBI: number of good PEBs: 80 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 32 UBI: total number of reserved PEBs: 48 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 2/0 UBIFS: mounted UBI device 0, volume 0, name "reserve2" UBIFS: mounted read-only UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs) UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: LZO UBIFS: reserved for root: 200807 bytes (196 KiB) Loading file '/mac_addr' to addr 0x02000000 with size 18 (0x00000012)... Done Set lan 2 WakeOnLan ok Enable HD1 Enable HD2 Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | In-Band | | egiga1 | RGMII | In-Band | | egiga2 | SGMII | 0x00 | egiga0, egiga1, egiga2 [PRIME] Hit any key to stop autoboot: 0 Marvell>> setenv bootdev 'usb' Marvell>> setenv device '0:1' Marvell>> setenv load_image_addr '0x02000000' Marvell>> setenv load_initrd_addr '0x2900000' Marvell>> setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage' Marvell>> setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' Marvell>> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' Marvell>> setenv bootcmd_usb 'echo Booting from USB ...; usb start; setenv fdt_skip_update yes; usb start; run usb_set_bootargs; if run load_image; then if run load_initrd; then bootm $load_image_addr $load_initrd_addr; else bootm $load_image_addr; fi; fi' Marvell>> run bootcmd_usb Booting from USB ... (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found loading Image ... ** Bad device usb 0 ** Marvell>>
mcmg2
Re: My Cloud Mirror Gen2 July 06, 2017 04:04PM |
98 % [......................................................................] 99 % [.........................................] [Type Ctrl-\ + c to quit] __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01_v1.04 (Jul 05 2017 - 16:59:05) Marvell version: 2014_T3.0p6 mvBoardIdIndexGet(boardId) = 1 Board: GrandTeton DB6820 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 1 GiB Map: Code: 0x3fece000:0x3ff95f50 BSS: 0x3ffef254 Stack: 0x3f9cdf20 Heap: 0x3f9ce000:0x3fece000 raise: Signal # 8 caught raise: Signal # 8 caught U-Boot Environment: 0x00000000:0x00080000 (NAND) NAND: ID: daad ,256 MiB MMC: mv_sdh: 0 PCI-e 0: Detected No Link. USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Creating 1 MTD partitions on "nand0": 0x00000f500000-0x00000ff00000 : "mtd=7" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=7" UBI: MTD device size: 10 MiB UBI: number of good PEBs: 80 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 32 UBI: total number of reserved PEBs: 48 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 2/0 UBIFS: mounted UBI device 0, volume 0, name "reserve2" UBIFS: mounted read-only UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs) UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: LZO UBIFS: reserved for root: 200807 bytes (196 KiB) Loading file '/mac_addr' to addr 0x02000000 with size 18 (0x00000012)... Done Set lan 2 WakeOnLan ok Enable HD1 Enable HD2 Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | In-Band | | egiga1 | RGMII | In-Band | | egiga2 | SGMII | 0x00 | egiga0, egiga1, egiga2 [PRIME] Hit any key to stop autoboot: 0 Marvell>> setenv bootdev 'usb' Marvell>> setenv device '0:1' Marvell>> setenv load_image_addr '0x02000000' Marvell>> setenv load_initrd_addr '0x2900000' Marvell>> setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage' Marvell>> setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' Marvell>> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' Marvell>> setenv bootcmd_usb 'echo Booting from USB ...; usb start; setenv fdt_skip_update yes; usb start; run usb_set_bootargs; if run load_image; then if run load_initrd; then bootm $load_image_addr $load_initrd_addr; else bootm $load_image_addr; fi; fi' Marvell>> run bootcmd_usb Booting from USB ... (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found loading Image ... ** Bad device usb 0 ** Marvell>> printenv CASset=max MALLOC_len=5 MPmode=SMP autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=nand read.e 0xa00000 0x500000 0x500000;nand read.e 0xf00000 0xa00000 0x500000;bootm 0xa00000 0xf00000 bootcmd_auto=stage_boot $boot_order bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootcmd_usb=echo Booting from USB ...; usb start; setenv fdt_skip_update yes; usb start; run usb_set_bootargs; if run load_image; then if run load_initrd; then bootm $load_image_addr $load_initrd_addr; else bootm $load_image_addr; fi; fi bootdelay=1 bootdev=usb cacheShare=no console=console=ttyS0,115200 device=0:1 device_partition=0:1 disaMvPnp=no eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:20:21:3e eth1mtu=1500 eth2addr=00:50:43:20:f2:3e eth2mtu=1500 eth3addr=00:50:43:21:f2:20 eth3mtu=1500 ethact=egiga2 ethaddr=00:50:43:f2:21:3e ethmtu=1500 ethprime=egiga2 fdt_addr=2040000 fdt_skip_update=yes fdtaddr=0x1000000 fdtfile=armada-38x-modular.dtb filesize=12 ide_path=/ image_name=uImage initrd_name=uInitrd ipaddr=192.168.11.110 kernel_addr_r=2080000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 load_image=echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage load_image_addr=0x02000000 load_initrd=echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x2900000 loadaddr=0x02000000 loads_echo=0 mtddevname=u-boot mtddevnum=0 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:5m(u-boot)ro,5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:3e:f2:20 nandEcc=nfcConfig=4bitecc netbsd_en=no netmask=255.255.255.0 netretry=no partition=nand0,0 pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rootpath=/srv/nfs/ sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scr serverip=192.168.11.114 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial usb0Mode=host usbActive=0 usbType=3 usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 3868/524284 bytes Marvell>>
Re: My Cloud Mirror Gen2 July 06, 2017 04:36PM |
Admin Registered: 13 years ago Posts: 19,094 |
scanning usb for storage devices... 0 Storage Device(s) found
Re: My Cloud Mirror Gen2 July 07, 2017 12:05AM |
Registered: 7 years ago Posts: 119 |
Quote
bodhi
hmartin is right, tt seems this u-boot does not bring up the USB drive, does not have power! How many USB ports this box has? did you try other USB port?
#if 0 //ALPHA_CUSTOMIZE, Casper marked, 20150525 ulong value32=0; /* disable USB led */ /* TODO: unplug USB power via uP */ value32 = *((ulong *)(0xF1018140)); value32 &= ~(1<<(48-32)); *((ulong *)(0xF1018140)) = value32; #endif
mcmg2
Re: My Cloud Mirror Gen2 July 08, 2017 03:42AM |
Re: My Cloud Mirror Gen2 July 08, 2017 05:09AM |
Registered: 7 years ago Posts: 119 |
Quote
mcmg2
hmartin, are you still working on patched uboot?
Quote
mcmg2
I'm waiting for new kwboot binary.
Re: My Cloud Mirror Gen2 July 08, 2017 05:30AM |
Registered: 7 years ago Posts: 119 |
setenv bootdev 'usb' setenv device '0:1' setenv load_image_addr '0x02000000' setenv load_initrd_addr '0x2900000' setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage' run load_image
Re: My Cloud Mirror Gen2 July 08, 2017 04:12PM |
Admin Registered: 13 years ago Posts: 19,094 |
Quote
After reviewing the source more and looking at the u-boot changes for ClearFrog, it seems that Western Digital has maybe disabled USB in u-boot. However this doesn't make any sense to me, since I assume MCM Gen 2 still allows for USB firmware recovery, and I do not see in u-boot source where they are enabling USB before loading the kernel/ramdisk from USB.
setenv bootdev 'usb' setenv device '0:1' setenv load_image_addr '0x02000000' setenv load_initrd_addr '0x2900000' setenv load_image 'usb start; echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage' run load_image
mcmg2
Re: My Cloud Mirror Gen2 July 08, 2017 04:21PM |
98 % [......................................................................] 99 % [..........................................] [Type Ctrl-\ + c to quit] __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01_v1.04 (Jul 08 2017 - 10:27:15) Marvell version: 2014_T3.0p6 mvBoardIdIndexGet(boardId) = 1 Board: GrandTeton DB6820 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 1 GiB Map: Code: 0x3fece000:0x3ff96000 BSS: 0x3ffef654 Stack: 0x3f9cdf20 Heap: 0x3f9ce000:0x3fece000 raise: Signal # 8 caught raise: Signal # 8 caught U-Boot Environment: 0x00000000:0x00080000 (NAND) NAND: ID: daad ,256 MiB MMC: mv_sdh: 0 PCI-e 0: Detected No Link. USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Creating 1 MTD partitions on "nand0": 0x00000f500000-0x00000ff00000 : "mtd=7" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=7" UBI: MTD device size: 10 MiB UBI: number of good PEBs: 80 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 32 UBI: total number of reserved PEBs: 48 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 3/0 UBIFS: mounted UBI device 0, volume 0, name "reserve2" UBIFS: mounted read-only UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs) UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: LZO UBIFS: reserved for root: 200807 bytes (196 KiB) Loading file '/mac_addr' to addr 0x02000000 with size 18 (0x00000012)... Done Set lan 2 WakeOnLan ok Enable HD1 Enable HD2 Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | In-Band | | egiga1 | RGMII | In-Band | | egiga2 | SGMII | 0x00 | egiga0, egiga1, egiga2 [PRIME] Hit any key to stop autoboot: 0 Marvell>> setenv bootdev 'usb' Marvell>> setenv device '0:1' Marvell>> setenv load_image_addr '0x02000000' Marvell>> setenv load_initrd_addr '0x2900000' Marvell>> setenv load_image 'usb start; echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage' Marvell>> run load_image (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found loading Image ... ** Bad device usb 0 ** Marvell>>
Re: My Cloud Mirror Gen2 July 08, 2017 04:27PM |
Admin Registered: 13 years ago Posts: 19,094 |
scanning usb for storage devices... 0 Storage Device(s) found
mcmg2
Re: My Cloud Mirror Gen2 July 08, 2017 04:40PM |
98 % [......................................................................] 99 % [..........................................] [Type Ctrl-\ + c to quit] __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01_v1.04 (Jul 08 2017 - 10:27:15) Marvell version: 2014_T3.0p6 mvBoardIdIndexGet(boardId) = 1 Board: GrandTeton DB6820 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 1 GiB Map: Code: 0x3fece000:0x3ff96000 BSS: 0x3ffef654 Stack: 0x3f9cdf20 Heap: 0x3f9ce000:0x3fece000 raise: Signal # 8 caught raise: Signal # 8 caught U-Boot Environment: 0x00000000:0x00080000 (NAND) NAND: ID: daad ,256 MiB MMC: mv_sdh: 0 PCI-e 0: Detected No Link. USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Creating 1 MTD partitions on "nand0": 0x00000f500000-0x00000ff00000 : "mtd=7" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=7" UBI: MTD device size: 10 MiB UBI: number of good PEBs: 80 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 32 UBI: total number of reserved PEBs: 48 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 3/0 UBIFS: mounted UBI device 0, volume 0, name "reserve2" UBIFS: mounted read-only UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs) UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: LZO UBIFS: reserved for root: 200807 bytes (196 KiB) Loading file '/mac_addr' to addr 0x02000000 with size 18 (0x00000012)... Done Set lan 2 WakeOnLan ok Enable HD1 Enable HD2 Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | In-Band | | egiga1 | RGMII | In-Band | | egiga2 | SGMII | 0x00 | egiga0, egiga1, egiga2 [PRIME] Hit any key to stop autoboot: 0 Marvell>> setenv bootdev 'usb' Marvell>> setenv device '0:1' Marvell>> setenv load_image_addr '0x02000000' Marvell>> setenv load_initrd_addr '0x2900000' Marvell>> setenv load_image 'usb start; echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage' Marvell>> run load_image (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found loading Image ... ** Bad device usb 0 ** Marvell>> run load_image (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found loading Image ... 3921006 bytes read in 422 ms (8.9 MiB/s) Marvell>>
Re: My Cloud Mirror Gen2 July 08, 2017 04:46PM |
Admin Registered: 13 years ago Posts: 19,094 |
scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found loading Image ... 3921006 bytes read in 422 ms (8.9 MiB/s)
setenv bootdev 'usb' setenv device '0:1' setenv load_image_addr '0x02000000' setenv load_initrd_addr '0x2900000' setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage' setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' setenv bootcmd_usb 'echo Booting from USB ...; usb start; setenv fdt_skip_update yes; usb start; run usb_set_bootargs; if run load_image; then if run load_initrd; then bootm $load_image_addr $load_initrd_addr; else bootm $load_image_addr; fi; fi' run bootcmd_usb
mcmg2
Re: My Cloud Mirror Gen2 July 08, 2017 07:29PM |
98 % [......................................................................] 99 % [..........................................] [Type Ctrl-\ + c to quit] __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01_v1.04 (Jul 08 2017 - 10:27:15) Marvell version: 2014_T3.0p6 mvBoardIdIndexGet(boardId) = 1 Board: GrandTeton DB6820 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 1 GiB Map: Code: 0x3fece000:0x3ff96000 BSS: 0x3ffef654 Stack: 0x3f9cdf20 Heap: 0x3f9ce000:0x3fece000 raise: Signal # 8 caught raise: Signal # 8 caught U-Boot Environment: 0x00000000:0x00080000 (NAND) NAND: ID: daad ,256 MiB MMC: mv_sdh: 0 PCI-e 0: Detected No Link. USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Creating 1 MTD partitions on "nand0": 0x00000f500000-0x00000ff00000 : "mtd=7" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=7" UBI: MTD device size: 10 MiB UBI: number of good PEBs: 80 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 32 UBI: total number of reserved PEBs: 48 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 3/0 UBIFS: mounted UBI device 0, volume 0, name "reserve2" UBIFS: mounted read-only UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs) UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: LZO UBIFS: reserved for root: 200807 bytes (196 KiB) Loading file '/mac_addr' to addr 0x02000000 with size 18 (0x00000012)... Done Set lan 2 WakeOnLan ok Enable HD1 Enable HD2 Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | In-Band | | egiga1 | RGMII | In-Band | | egiga2 | SGMII | 0x00 | egiga0, egiga1, egiga2 [PRIME] Hit any key to stop autoboot: 0 Marvell>> setenv bootdev 'usb' Marvell>> setenv device '0:1' Marvell>> setenv load_image_addr '0x02000000' Marvell>> setenv load_initrd_addr '0x2900000' Marvell>> setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage' Marvell>> setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' Marvell>> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' Marvell>> setenv bootcmd_usb 'echo Booting from USB ...; usb start; setenv fdt_skip_update yes; usb start; run usb_set_bootargs; if run load_image; then if run load_initrd; then bootm $load_image_addr $load_initrd_addr; else bootm $load_image_addr; fi; fi' Marvell>> run bootcmd_usb Booting from USB ... (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found loading Image ... 3921006 bytes read in 422 ms (8.9 MiB/s) loading uInitrd ... 6210503 bytes read in 490 ms (12.1 MiB/s) ## Booting image at 02000000 ... ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-4.9.0-mvebu-tld-12 Created: 2017-07-06 20:09:30 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3920942 Bytes = 3.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02900000 ... Image Name: initramfs-4.9.0-mvebu-tld-12 Created: 2017-02-03 23:57:32 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6210439 Bytes = 5.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.0-mvebu-tld-12 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt:Machine model: WD MyCloud Mirror gen2 (Armada 385) [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] ------------[ cut here ]------------ [ 0.000000] WARNING: CPU: 0 PID: 0 at kernel/printk/printk.c:2612 register_console+0x3c/0x398 [ 0.000000] console 'earlycon0' already registered [ 0.000000] Modules linked in: [ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 4.9.0-mvebu-tld-12 #2 [ 0.000000] Hardware name: Marvell Armada 380/385 (Device Tree) [ 0.000000] [<c01160bc>] (unwind_backtrace) from [<c0110bb4>] (show_stack+0x10/0x14) [ 0.000000] [<c0110bb4>] (show_stack) from [<c04ba5a4>] (dump_stack+0x70/0x8c) [ 0.000000] [<c04ba5a4>] (dump_stack) from [<c0123ce0>] (__warn+0xc8/0xfc) [ 0.000000] [<c0123ce0>] (__warn) from [<c0123d48>] (warn_slowpath_fmt+0x34/0x44) [ 0.000000] [<c0123d48>] (warn_slowpath_fmt) from [<c0171b1c>] (register_console+0x3c/0x398) [ 0.000000] [<c0171b1c>] (register_console) from [<c0c04dc0>] (setup_early_printk+0x14/0x24) [ 0.000000] [<c0c04dc0>] (setup_early_printk) from [<c0c00478>] (do_early_param+0x6c/0xbc) [ 0.000000] [<c0c00478>] (do_early_param) from [<c013f774>] (parse_args+0x2dc/0x40c) [ 0.000000] [<c013f774>] (parse_args) from [<c0c0088c>] (parse_early_options+0x2c/0x3c) [ 0.000000] [<c0c0088c>] (parse_early_options) from [<c0c008c8>] (parse_early_param+0x2c/0x44) [ 0.000000] [<c0c008c8>] (parse_early_param) from [<c0c03350>] (setup_arch+0x4fc/0xa24) [ 0.000000] [<c0c03350>] (setup_arch) from [<c0c00934>] (start_kernel+0x50/0x390) [ 0.000000] [<c0c00934>] (start_kernel) from [<0000807c>] (0x807c) [ 0.000000] ---[ end trace 0000000000000000 ]--- [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 15 pages/cpu @ef7cb000 s30796 r8192 d22452 u61440 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttyS0,115200 earlyprintk console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1019924K/1048576K available (8192K kernel code, 690K rwdata, 2052K rodata, 1024K init, 386K bss, 28652K reserved, 0K cma-reserved, 262144K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0daca28 ( 691 kB) [ 0.000000] .bss : 0xc0daca28 - 0xc0e0d4f8 ( 387 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] ------------[ cut here ]------------ [ 0.000000] WARNING: CPU: 0 PID: 0 at drivers/irqchip/irq-gic.c:1295 gic_of_setup+0x6c/0xb8 [ 0.000000] unable to map gic dist registers [ 0.000000] Modules linked in: [ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 4.9.0-mvebu-tld-12 #2 [ 0.000000] Hardware name: Marvell Armada 380/385 (Device Tree) [ 0.000000] [<c01160bc>] (unwind_backtrace) from [<c0110bb4>] (show_stack+0x10/0x14) [ 0.000000] [<c0110bb4>] (show_stack) from [<c04ba5a4>] (dump_stack+0x70/0x8c) [ 0.000000] [<c04ba5a4>] (dump_stack) from [<c0123ce0>] (__warn+0xc8/0xfc) [ 0.000000] [<c0123ce0>] (__warn) from [<c0123d48>] (warn_slowpath_fmt+0x34/0x44) [ 0.000000] [<c0123d48>] (warn_slowpath_fmt) from [<c04e8c20>] (gic_of_setup+0x6c/0xb8) [ 0.000000] [<c04e8c20>] (gic_of_setup) from [<c0c2e290>] (gic_of_init+0x64/0x240) [ 0.000000] [<c0c2e290>] (gic_of_init) from [<c0c3d450>] (of_irq_init+0x190/0x2e8) [ 0.000000] [<c0c3d450>] (of_irq_init) from [<c0c08b20>] (mvebu_init_irq+0x8/0x64) [ 0.000000] [<c0c08b20>] (mvebu_init_irq) from [<c0c02708>] (init_IRQ+0x28/0x88) [ 0.000000] [<c0c02708>] (init_IRQ) from [<c0c00ad8>] (start_kernel+0x1f4/0x390) [ 0.000000] [<c0c00ad8>] (start_kernel) from [<0000807c>] (0x807c) [ 0.000000] ---[ end trace f68728a0d3053b52 ]--- [ 0.000000] OF: of_irq_init: children remain, but no parents [ 0.000000] Unable to handle kernel NULL pointer dereference at virtual address 00000000 [ 0.000000] pgd = c0004000 [ 0.000000] [00000000] *pgd=00000000 [ 0.000000] Internal error: Oops: 5 [#1] PREEMPT SMP ARM [ 0.000000] Modules linked in: [ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 4.9.0-mvebu-tld-12 #2 [ 0.000000] Hardware name: Marvell Armada 380/385 (Device Tree) [ 0.000000] task: c0d08480 task.stack: c0d00000 [ 0.000000] PC is at scu_enable+0x0/0x50 [ 0.000000] LR is at mvebu_init_irq+0x34/0x64 [ 0.000000] pc : [<c01146fc>] lr : [<c0c08b4c>] psr: a00000d3 [ 0.000000] sp : c0d01fb0 ip : 00000018 fp : 00000000 [ 0.000000] r10: 00000000 r9 : c0c51a28 r8 : efffcd00 [ 0.000000] r7 : c0d04100 r6 : ffffffff r5 : c0daca40 r4 : ef7ed75c [ 0.000000] r3 : c0dacf10 r2 : ffffffff r1 : ffffffff r0 : 00000000 [ 0.000000] Flags: NzCv IRQs off FIQs off Mode SVC_32 ISA ARM Segment none [ 0.000000] Control: 10c5387d Table: 0000404a DAC: 00000051 [ 0.000000] Process swapper/0 (pid: 0, stack limit = 0xc0d00220) [ 0.000000] Stack: (0xc0d01fb0 to 0xc0d02000) [ 0.000000] 1fa0: c0c51a18 c0c02708 00000001 c0c00ad8 [ 0.000000] 1fc0: ffffffff ffffffff 00000000 c0c00694 00000000 c0c51a28 00000000 c0daccd4 [ 0.000000] 1fe0: c0d04118 c0c51a24 c0d09910 0000406a 414fc091 0000807c 00000000 00000000 [ 0.000000] [<c01146fc>] (scu_enable) from [<c0c51a18>] (0xc0c51a18) [ 0.000000] Code: e12fff1e c0d08140 c0114388 c0ab2954 (e5903000) [ 0.000000] ---[ end trace f68728a0d3053b53 ]--- [ 0.000000] Kernel panic - not syncing: Attempted to kill the idle task! [ 0.000000] ---[ end Kernel panic - not syncing: Attempted to kill the idle task!
Re: My Cloud Mirror Gen2 July 08, 2017 10:08PM |
Admin Registered: 13 years ago Posts: 19,094 |
mcmg2
Re: My Cloud Mirror Gen2 July 08, 2017 11:39PM |
Re: My Cloud Mirror Gen2 July 09, 2017 12:44AM |
Admin Registered: 13 years ago Posts: 19,094 |
Re: My Cloud Mirror Gen2 July 09, 2017 03:23AM |
Registered: 7 years ago Posts: 119 |
Quote
bodhi
I have not seen the Mirror Gen 2 DTS before so not sure. Let hmartin help you.
Quote
mcmg2
I used dtb file on this page by hmartin.
mcmg2
Re: My Cloud Mirror Gen2 July 09, 2017 06:24AM |
UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=7" UBI: MTD device size: 10 MiB UBI: number of good PEBs: 80 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 32 UBI: total number of reserved PEBs: 48 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 3/0 UBIFS: mounted UBI device 0, volume 0, name "reserve2" UBIFS: mounted read-only UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs) UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: LZO UBIFS: reserved for root: 200807 bytes (196 KiB) Loading file '/mac_addr' to addr 0x02000000 with size 18 (0x00000012)... Done Set lan 2 WakeOnLan ok Enable HD1 Enable HD2 Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | In-Band | | egiga1 | RGMII | In-Band | | egiga2 | SGMII | 0x00 | egiga0, egiga1, egiga2 [PRIME] Hit any key to stop autoboot: 0 Marvell>> setenv bootdev 'usb' Marvell>> setenv device '0:1' Marvell>> setenv load_image_addr '0x02000000' Marvell>> setenv load_initrd_addr '0x2900000' Marvell>> setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage' Marvell>> setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' Marvell>> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' Marvell>> setenv bootcmd_usb 'echo Booting from USB ...; usb start; setenv fdt_skip_update yes; usb start; run usb_set_bootargs; if run load_image; then if run load_initrd; then bootm $load_image_addr $load_initrd_addr; else bootm $load_image_addr; fi; fi' Marvell>> run bootcmd_usb Booting from USB ... (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found loading Image ... 3920526 bytes read in 421 ms (8.9 MiB/s) loading uInitrd ... 6210503 bytes read in 490 ms (12.1 MiB/s) ## Booting image at 02000000 ... ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-4.9.0-mvebu-tld-12 Created: 2017-07-09 9:45:53 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3920462 Bytes = 3.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02900000 ... Image Name: initramfs-4.9.0-mvebu-tld-12 Created: 2017-02-03 23:57:32 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6210439 Bytes = 5.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.0-mvebu-tld-12 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt:Machine model: Western Digital MyCloud EX2 Ultra [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] ------------[ cut here ]------------ [ 0.000000] WARNING: CPU: 0 PID: 0 at kernel/printk/printk.c:2612 register_console+0x3c/0x398 [ 0.000000] console 'earlycon0' already registered [ 0.000000] Modules linked in: [ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 4.9.0-mvebu-tld-12 #2 [ 0.000000] Hardware name: Marvell Armada 380/385 (Device Tree) [ 0.000000] [<c01160bc>] (unwind_backtrace) from [<c0110bb4>] (show_stack+0x10/0x14) [ 0.000000] [<c0110bb4>] (show_stack) from [<c04ba5a4>] (dump_stack+0x70/0x8c) [ 0.000000] [<c04ba5a4>] (dump_stack) from [<c0123ce0>] (__warn+0xc8/0xfc) [ 0.000000] [<c0123ce0>] (__warn) from [<c0123d48>] (warn_slowpath_fmt+0x34/0x44) [ 0.000000] [<c0123d48>] (warn_slowpath_fmt) from [<c0171b1c>] (register_console+0x3c/0x398) [ 0.000000] [<c0171b1c>] (register_console) from [<c0c04dc0>] (setup_early_printk+0x14/0x24) [ 0.000000] [<c0c04dc0>] (setup_early_printk) from [<c0c00478>] (do_early_param+0x6c/0xbc) [ 0.000000] [<c0c00478>] (do_early_param) from [<c013f774>] (parse_args+0x2dc/0x40c) [ 0.000000] [<c013f774>] (parse_args) from [<c0c0088c>] (parse_early_options+0x2c/0x3c) [ 0.000000] [<c0c0088c>] (parse_early_options) from [<c0c008c8>] (parse_early_param+0x2c/0x44) [ 0.000000] [<c0c008c8>] (parse_early_param) from [<c0c03350>] (setup_arch+0x4fc/0xa24) [ 0.000000] [<c0c03350>] (setup_arch) from [<c0c00934>] (start_kernel+0x50/0x390) [ 0.000000] [<c0c00934>] (start_kernel) from [<0000807c>] (0x807c) [ 0.000000] ---[ end trace 0000000000000000 ]--- [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 15 pages/cpu @ef7cc000 s30796 r8192 d22452 u61440 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttyS0,115200 libata.force=3.0G root=LABEL=rootfs earlyprintk console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1019928K/1048576K available (8192K kernel code, 690K rwdata, 2052K rodata, 1024K init, 386K bss, 28648K reserved, 0K cma-reserved, 262144K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0daca28 ( 691 kB) [ 0.000000] .bss : 0xc0daca28 - 0xc0e0d4f8 ( 387 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] mvebu_mbus: [Firmware Warn]: deprecated mbus-mvebu Device Tree, suspend/resume will not work [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 D prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001 [ 0.000000] Switching to timer-based delay loop, resolution 40ns [ 0.000004] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns [ 0.007883] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.019112] Console: colour dummy device 80x30 [ 0.023628] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000) [ 0.034036] pid_max: default: 32768 minimum: 301 [ 0.038804] Security Framework initialized [ 0.043006] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.049681] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.057258] CPU: Testing write buffer coherency: ok [ 0.062350] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.068091] Setting up static identity map for 0x100000 - 0x100058 [ 0.074521] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4 [ 0.079804] mvebu-pmsu: Initializing Power Management Service Unit [ 0.283604] Booting CPU 1 [ 0.286475] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.286532] Brought up 2 CPUs [ 0.295294] SMP: Total of 2 processors activated (100.00 BogoMIPS). [ 0.301614] CPU: All CPU(s) started in SVC mode. [ 0.306885] devtmpfs: initialized [ 0.312771] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.320755] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.330692] prandom: seed boundary self test passed [ 0.337655] prandom: 100 self tests passed [ 0.341816] pinctrl core: initialized pinctrl subsystem [ 0.347850] NET: Registered protocol family 16 [ 0.353009] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.383453] cpuidle: using governor ladder [ 0.413420] cpuidle: using governor menu [ 0.417536] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.425610] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.483819] vgaarb: loaded [ 0.486858] SCSI subsystem initialized [ 0.491156] usbcore: registered new interface driver usbfs [ 0.496812] usbcore: registered new interface driver hub [ 0.502247] usbcore: registered new device driver usb [ 0.507598] media: Linux media interface: v0.10 [ 0.512242] Linux video capture interface: v2.00 [ 0.517922] clocksource: Switched to clocksource armada_370_xp_clocksource [ 0.554187] VFS: Disk quotas dquot_6.6.0 [ 0.558258] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.573535] NET: Registered protocol family 2 [ 0.578403] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.585545] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.592140] TCP: Hash tables configured (established 8192 bind 8192) [ 0.598601] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.604596] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.611149] NET: Registered protocol family 1 [ 0.615837] RPC: Registered named UNIX socket transport module. [ 0.621830] RPC: Registered udp transport module. [ 0.626596] RPC: Registered tcp transport module. [ 0.631385] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.638023] Unpacking initramfs... [ 0.885851] Freeing initrd memory: 6068K (c2900000 - c2eed000) [ 0.891957] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.898730] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.908074] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.914285] audit: initializing netlink subsys (disabled) [ 0.919790] audit: type=2000 audit(0.910:1): initialized [ 0.925621] Initialise system trusted keyrings [ 0.930300] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 0.936870] zbud: loaded [ 0.940049] NFS: Registering the id_resolver key type [ 0.945171] Key type id_resolver registered [ 0.949436] Key type id_legacy registered [ 0.953517] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.960281] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.966845] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.974289] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.980927] orangefs_init: module version upstream loaded [ 0.988534] Key type asymmetric registered [ 0.992698] Asymmetric key parser 'x509' registered [ 0.997667] bounce: pool size: 64 pages [ 1.001667] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.009126] io scheduler noop registered [ 1.013114] io scheduler deadline registered [ 1.017463] io scheduler cfq registered (default) [ 1.023155] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 1.031823] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00 [ 1.038772] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 1.045095] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 1.052034] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.058042] PCI: bus0: Fast back to back transfers disabled [ 1.063679] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.071751] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.079932] PCI: bus1: Fast back to back transfers enabled [ 1.085607] PCI: bus2: Fast back to back transfers enabled [ 1.091211] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.096242] pci 0000:00:02.0: PCI bridge to [bus 02] [ 1.101767] mv_xor f1060800.xor: Marvell shared XOR driver [ 1.168404] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.176022] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.238391] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.296777] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.304734] console [ttyS0] disabled [ 1.328476] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 23, base_baud = 12500000) is a 16550A [ 1.337504] console [ttyS0] enabled [ 1.337504] console [ttyS0] enabled [ 1.344604] bootconsole [earlycon0] disabled [ 1.344604] bootconsole [earlycon0] disabled [ 1.373980] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 24, base_baud = 12500000) is a 16550A [ 1.383998] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 1.393108] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 1.402790] scsi host0: ahci-mvebu [ 1.406516] scsi host1: ahci-mvebu [ 1.410173] ata1: FORCE: PHY spd limit set to 3.0Gbps [ 1.415249] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 42 [ 1.423212] ata2: FORCE: PHY spd limit set to 3.0Gbps [ 1.428295] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 42 [ 1.436787] pxa3xx-nand f10d0000.flash: This platform can't do DMA on this device [ 1.444695] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda [ 1.451091] nand: Hynix H27U2G8F2CTR-BC [ 1.454945] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.462560] pxa3xx-nand f10d0000.flash: ECC strength 16, ECC step size 2048 [ 1.469769] Bad block table found at page 131008, version 0x01 [ 1.475967] Bad block table found at page 130944, version 0x01 [ 1.482069] 8 ofpart partitions found on MTD device pxa3xx_nand-0 [ 1.488200] Creating 8 MTD partitions on "pxa3xx_nand-0": [ 1.493627] 0x000000000000-0x000000500000 : "U-Boot" [ 1.509457] 0x000000500000-0x000000a00000 : "uImage" [ 1.525183] 0x000000a00000-0x000000f00000 : "uRamdisk" [ 1.541078] 0x000000f00000-0x00000c800000 : "image.cfs" [ 1.557798] 0x00000c800000-0x00000d700000 : "rescue fw" [ 1.573813] 0x00000d700000-0x00000eb00000 : "config" [ 1.589607] 0x00000eb00000-0x00000f500000 : "reserve1" [ 1.605530] 0x00000f500000-0x00000ff00000 : "reserve2" [ 1.622079] m25p80 spi0.0: unrecognized JEDEC id bytes: ff, ff, ff [ 1.628901] libphy: Fixed MDIO Bus: probed [ 1.633327] libphy: mdio_driver_register: mv88e6085 [ 1.638430] libphy: orion_mdio_bus: probed [ 1.647959] mvneta f1034000.ethernet eth0: Using random mac address 9e:d4:26:33:24:1a [ 1.656016] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.662597] ehci-pci: EHCI PCI platform driver [ 1.667104] ehci-orion: EHCI orion driver [ 1.671447] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.676797] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 1 [ 1.684411] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.693022] xhci-hcd f10f0000.usb3: irq 45, io mem 0xf10f0000 [ 1.698913] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.705733] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.712997] usb usb1: Product: xHCI Host Controller [ 1.717896] usb usb1: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.724374] usb usb1: SerialNumber: f10f0000.usb3 [ 1.729493] hub 1-0:1.0: USB hub found [ 1.733283] hub 1-0:1.0: 1 port detected [ 1.737414] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.742773] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 1.750358] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.758565] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.759227] ata1: SATA link down (SStatus 0 SControl 320) [ 1.769178] ata2: SATA link down (SStatus 0 SControl 320) [ 1.776247] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.783510] usb usb2: Product: xHCI Host Controller [ 1.788417] usb usb2: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.794885] usb usb2: SerialNumber: f10f0000.usb3 [ 1.799970] hub 2-0:1.0: USB hub found [ 1.803756] hub 2-0:1.0: 1 port detected [ 1.807990] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.813338] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 3 [ 1.820934] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.829533] xhci-hcd f10f8000.usb3: irq 46, io mem 0xf10f8000 [ 1.835396] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.842352] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.849628] usb usb3: Product: xHCI Host Controller [ 1.854528] usb usb3: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.861005] usb usb3: SerialNumber: f10f8000.usb3 [ 1.866073] hub 3-0:1.0: USB hub found [ 1.869872] hub 3-0:1.0: 1 port detected [ 1.874009] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.879362] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 1.886929] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.895140] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.901970] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.909304] usb usb4: Product: xHCI Host Controller [ 1.914203] usb usb4: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.920681] usb usb4: SerialNumber: f10f8000.usb3 [ 1.925747] hub 4-0:1.0: USB hub found [ 1.929544] hub 4-0:1.0: 1 port detected [ 1.933779] usbcore: registered new interface driver usblp [ 1.939378] usbcore: registered new interface driver usb-storage [ 1.945598] mousedev: PS/2 mouse device common for all mice [ 1.951814] armada38x-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 [ 1.959705] i2c /dev entries driver [ 1.975164] orion_wdt: Initial timeout 171 sec [ 1.981593] marvell-cesa f1090000.crypto: CESA device successfully registered [ 1.988978] hidraw: raw HID events driver (C) Jiri Kosina [ 1.994735] usbcore: registered new interface driver usbhid [ 2.000347] usbhid: USB HID core driver [ 2.004365] drop_monitor: Initializing network drop monitor service [ 2.010713] Netfilter messages via NETLINK v0.30. [ 2.015450] ip_set: protocol 6 [ 2.018787] NET: Registered protocol family 10 [ 2.023821] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.030805] NET: Registered protocol family 17 [ 2.035435] 8021q: 802.1Q VLAN Support v1.8 [ 2.039770] Key type dns_resolver registered [ 2.044191] ThumbEE CPU extension supported. [ 2.048499] Registering SWP/SWPB emulation handler [ 2.053825] registered taskstats version 1 [ 2.057957] Loading compiled-in X.509 certificates [ 2.062804] zswap: loaded using pool lzo/zbud [ 2.111841] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 2.122562] Key type big_key registered [ 2.130450] Key type encrypted registered [ 2.135579] armada38x-rtc f10a3800.rtc: setting system clock to 2017-07-09 11:21:42 UTC (1499599302) [ 2.145944] Freeing unused kernel memory: 1024K (c0c00000 - c0d00000) Loading, please wait... [ 2.191854] systemd-udevd[1315]: starting version 215 [ 2.198013] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.290290] usb 1-1: New USB device found, idVendor=090c, idProduct=1000 [ 2.297041] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.305334] usb 1-1: Product: POLLEX 8G [ 2.309211] usb 1-1: Manufacturer: SRT [ 2.312979] usb 1-1: SerialNumber: 033113111111135234000373 [ 2.319103] usb-storage 1-1:1.0: USB Mass Storage device detected [ 2.335489] scsi host2: usb-storage 1-1:1.0 [ 2.479908] usbcore: registered new interface driver uas [ 3.368653] scsi 2:0:0:0: Direct-Access SRT POLLEX 8G 1100 PQ: 0 ANSI: 4 [ 3.379416] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 3.385091] sd 2:0:0:0: [sda] 15728640 512-byte logical blocks: (8.05 GB/7.50 GiB) [ 3.393830] sd 2:0:0:0: [sda] Write Protect is off [ 3.399344] sd 2:0:0:0: [sda] No Caching mode page found [ 3.404681] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 3.413691] sda: sda1 [ 3.418386] sd 2:0:0:0: [sda] Attached SCSI removable disk [ 3.457617] random: fast init done Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. modprobe: module ext3 not found in modules.dep Begin: Will now check root file system ... fsck from util-linux 2.25.2 fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sda1 fsck exited with status code 8 done. Warning: File system check failed but did not detect errors [ 17.613718] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 17.622373] EXT4-fs (sda1): INFO: recovery required on readonly filesystem [ 17.629297] EXT4-fs (sda1): write access will be enabled during recovery [ 17.671725] EXT4-fs (sda1): recovery complete [ 17.684412] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 18.604414] systemd-udevd[1520]: starting version 215 . ok [ ok ] Synthesizing the initial hotplug events...done. [ ok ] Waiting for /dev to be fully populated...done. [ ok ] Activating swap...done. [ 19.905031] EXT4-fs (sda1): re-mounted. Opts: (null) [ ok ] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.25.2 done. [ ok ] Cleaning up temporary files... /tmp. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables ...done. [ 21.178679] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1 Copyright 2004-2014 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/9e:d4:26:33:24:1a Sending on LPF/eth0/9e:d4:26:33:24:1a Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6 [ 25.368394] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 25.376278] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 33.770652] random: crng init done DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6 DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPOFFER from 192.168.2.1 DHCPACK from 192.168.2.1 bound to 192.168.2.109 -- renewal in 40836 seconds. done. [ ok ] Starting rpcbind daemon.... [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 2444 (syslogd) . ok [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Starting NTP server: ntpd. [ ok ] Starting system message bus: dbus. [ ok ] Starting periodic command scheduler: cron. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 2443 (klogd) . ok Debian GNU/Linux 8 debian ttyS0 debian login:
mcmg2
Re: My Cloud Mirror Gen2 July 09, 2017 06:37AM |
debian login: root Password: Last login: Fri Feb 3 22:22:51 PST 2017 from 192.168.0.100 on pts/0 Linux debian 4.9.0-mvebu-tld-12 #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. debian 192.168.2.109 Western Digital MyCloud EX2 Ultra Linux version 4.9.0-mvebu-tld-12 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 04:26:58 up 5 min, 1 user, load average: 0.01, 0.06, 0.03 root@debian:~# printenv SHELL=/bin/bash TERM=linux HUSHLOGIN=FALSE USER=root MAIL=/var/mail/root PATH=/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin PWD=/root SHLVL=1 HOME=/root LOGNAME=root _=/usr/bin/printenv root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 00500000 00020000 "U-Boot" mtd1: 00500000 00020000 "uImage" mtd2: 00500000 00020000 "uRamdisk" mtd3: 0b900000 00020000 "image.cfs" mtd4: 00f00000 00020000 "rescue fw" mtd5: 01400000 00020000 "config" mtd6: 00a00000 00020000 "reserve1" mtd7: 00a00000 00020000 "reserve2" root@debian:~# fw_printenv Warning: Bad CRC, using default environment bootargs= bootcmd=bootp; setenv bootargs root=/dev/nfs nfsroot=${serverip}:${rootpath} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; bootm bootdelay=3 baudrate=115200 stdin=serial,cros-ec-keyb stdout=serial,lcd stderr=serial,lcd root@debian:~#