Upgrading Debian Distribution
Posted by bodhi
|
Re: Upgrading to Debian stretch January 30, 2018 01:50PM |
Registered: 6 years ago Posts: 21 |
Now I have set the label as told to rootfs correctly.
But still I have no luck. :( The kernel failed to run. The LED color is still amber.
Yes, I don't have a serial console with a physical cable attached. At the moment I can only use the netconsole as mentioned in the other thread.
Any chance to get it work? :)
Tom
root@debian:~# e2label /dev/sdb1 rootfs root@debian:~#
But still I have no luck. :( The kernel failed to run. The LED color is still amber.
Yes, I don't have a serial console with a physical cable attached. At the moment I can only use the netconsole as mentioned in the other thread.
Any chance to get it work? :)
Tom
|
Re: Upgrading to Debian stretch January 30, 2018 04:27PM |
Admin Registered: 13 years ago Posts: 18,545 |
Tom,
> Yes, I don't have a serial console with a physical
> cable attached. At the moment I can only use the
> netconsole as mentioned in the other thread.
>
> Any chance to get it work? :)
It is quite easy to run a new rootfs using Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2 from the release thread:
https://forum.doozan.com/read.php?2,12096
Your current rootfs must have something wrong that we cannot see easily without serial console. So if you need to keep your current rootfs and only upgrade, I think you should connect serial console. After that, this problem can be solved in a few minutes.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> Yes, I don't have a serial console with a physical
> cable attached. At the moment I can only use the
> netconsole as mentioned in the other thread.
>
> Any chance to get it work? :)
It is quite easy to run a new rootfs using Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2 from the release thread:
https://forum.doozan.com/read.php?2,12096
Your current rootfs must have something wrong that we cannot see easily without serial console. So if you need to keep your current rootfs and only upgrade, I think you should connect serial console. After that, this problem can be solved in a few minutes.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Upgrading to Debian stretch January 31, 2018 04:48PM |
Registered: 6 years ago Posts: 21 |
Strange....
The Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi is also not working. Same behavior as before with the other kernel.
Maybe still an incorrect environment var?
The Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi is also not working. Same behavior as before with the other kernel.
Maybe still an incorrect environment var?
arcNumber=2097 baudrate=115200 bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset bootcmd_pogo=run bootcmd_rescue bootcmd_rescue=run set_bootargs_rescue; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000 bootdelay=10 console=ttyS0,115200 ethact=egiga0 ethaddr=00:10:75:1A:B8:8D force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi if_netconsole=ping $serverip ipaddr=192.168.0.16 led_error=orange blinking led_exit=green off led_init=green blinking mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) ncip=192.168.0.1 partition=nand0,2 pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi preboot=run if_netconsole start_netconsole rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi rescue_installed=1 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params serverip=192.168.0.1 set_bootargs_rescue=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=nc stdin=nc stdout=nc ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_device=0:1 usb_init=run usb_scan usb_root=/dev/sda1 usb_rootdelay=10 usb_rootfstype=ext2 usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done usb_scan_1=usb=0:1 dev=sda1 usb_scan_2=usb=1:1 dev=sdb1 usb_scan_3=usb=2:1 dev=sdc1 usb_scan_4=usb=3:1 dev=sdd1 usb_scan_list=1 2 3 4 usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params Environment size: 2839/131068 bytes u-boot>>Tom
|
Re: Upgrading to Debian stretch January 31, 2018 05:53PM |
Admin Registered: 13 years ago Posts: 18,545 |
Tom,
We are going way off topic here. So please create a new thread for this booting problem and post the complete boot log of your attempt to boot Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
We are going way off topic here. So please create a new thread for this booting problem and post the complete boot log of your attempt to boot Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Upgrading to Debian stretch September 05, 2019 09:08PM |
Registered: 6 years ago Posts: 178 |
Not sure if this will help anyone but putting it out there, running Pogoplug pro v3 effectively with Debian 10 Buster, all I did was changed the etc/apt/sources.list with the following:
then run
have had no issues for the last month and switched it to my main machine after testing.
I also took a stab at testing Debian 11 Bullseye on my test machine after that and it works well thus far but it is still in the test phase so I would not recommend using it on a production machine.
Echowarrior108
device: pogoplug-pro v3
Currently running:
Debian GNU/Linux Bullseye 12-9-22
Linux 5.4.224-oxnas-tld-1 armv6l GNU/Linux 11-27-22
deb http://deb.debian.org/debian/ stable main contrib non-free deb-src http://deb.debian.org/debian/ stable main contrib non-free deb http://deb.debian.org/debian/ stable-updates main contrib non-free deb-src http://deb.debian.org/debian/ stable-updates main contrib non-free
then run
apt-get update apt-get dist-upgrade
have had no issues for the last month and switched it to my main machine after testing.
I also took a stab at testing Debian 11 Bullseye on my test machine after that and it works well thus far but it is still in the test phase so I would not recommend using it on a production machine.
Echowarrior108
device: pogoplug-pro v3
Currently running:
Debian GNU/Linux Bullseye 12-9-22
Linux 5.4.224-oxnas-tld-1 armv6l GNU/Linux 11-27-22
|
Re: Upgrading to Debian stretch September 21, 2019 05:57PM |
Registered: 6 years ago Posts: 178 |
Just an update both my plugs are doing great with the upgrades, have had no issues at all.... Nice to just post without needing help this time:)m
Echowarrior108
device: pogoplug-pro v3
Currently running:
Debian GNU/Linux Bullseye 12-9-22
Linux 5.4.224-oxnas-tld-1 armv6l GNU/Linux 11-27-22
Edited 1 time(s). Last edit at 10/24/2019 10:42PM by echowarrior108.
Echowarrior108
device: pogoplug-pro v3
Currently running:
Debian GNU/Linux Bullseye 12-9-22
Linux 5.4.224-oxnas-tld-1 armv6l GNU/Linux 11-27-22
Edited 1 time(s). Last edit at 10/24/2019 10:42PM by echowarrior108.
|
Nuno
Re: Upgrading to Debian stretch and buster October 12, 2019 12:33PM |
While trying to update to buster, I followed the instructions in this thread and tried to use the "slow" approach:
After a reboot everything seemed fine (except maybe samba, but I planned to address that later)
Then I tried to complete the upgrade:
This seemed to complete without any error, but after issuing a reboot command, my GoFlex Home seems not to boot. It is not accessible via the usual SSH connection and I can't ping it, even though the led is a solid green color...
These last commands, which seemed to run ok and rather fast, gave the following output:
Thanks!...
apt-get update apt-get upgrade
After a reboot everything seemed fine (except maybe samba, but I planned to address that later)
Then I tried to complete the upgrade:
apt-get update apt-get dist-upgrade
This seemed to complete without any error, but after issuing a reboot command, my GoFlex Home seems not to boot. It is not accessible via the usual SSH connection and I can't ping it, even though the led is a solid green color...
These last commands, which seemed to run ok and rather fast, gave the following output:
root@Cypher:~# apt dist-upgrade Reading package lists... Done Building dependency tree Reading state information... Done Calculating upgrade... Done The following packages were automatically installed and are no longer required: gnupg-agent libavcodec57 libavformat57 libavutil55 libbind9-140 libbluray1 libcurl3-gnutls libdns-export162 libdns162 libevent-2.0-5 libf2fs0 libfile-copy-recursive-perl libgdbm3 libicu57 libidn11 libisc-export160 libisc160 libisccc140 libisccfg140 liblwres141 libminiupnpc10 libntfs-3g871 libperl5.24 libprocps6 libssl1.0.2 libswresample2 libunistring0 libustr-1.0-1 libva-drm1 libva-x11-1 libva1 libvpx4 libwebpmux2 libx264-148 libx265-95 update-inetd Use 'apt autoremove' to remove them. The following packages will be REMOVED: liblzma2 libtirpc1 The following NEW packages will be installed: libtirpc-common libtirpc3 The following packages will be upgraded: liblzma5 nfs-common nfs-kernel-server rpcbind 4 upgraded, 2 newly installed, 2 to remove and 0 not upgraded. Need to get 598 kB of archives. After this operation, 394 kB disk space will be freed. Do you want to continue? [Y/n] Get:1 http://ftp.us.debian.org/debian buster/main armel rpcbind armel 1.2.5-0.3 [41.2 kB] Get:2 http://ftp.us.debian.org/debian buster/main armel nfs-kernel-server armel 1:1.3.4-2.5 [109 kB] Get:3 http://ftp.us.debian.org/debian buster/main armel nfs-common armel 1:1.3.4-2.5 [207 kB] Get:4 http://ftp.us.debian.org/debian buster/main armel libtirpc-common all 1.1.4-0.4 [16.7 kB] Get:5 http://ftp.us.debian.org/debian buster/main armel libtirpc3 armel 1.1.4-0.4 [79.4 kB] Get:6 http://ftp.us.debian.org/debian buster/main armel liblzma5 armel 5.2.4-1 [144 kB] Fetched 598 kB in 1s (579 kB/s) (Reading database ... 24827 files and directories currently installed.) Removing liblzma2 (5.0.0-2) ... (Reading database ... 24817 files and directories currently installed.) Preparing to unpack .../rpcbind_1.2.5-0.3_armel.deb ... [ ok ] Stopping RPC port mapper daemon: rpcbind. Unpacking rpcbind (1.2.5-0.3) over (0.2.3-0.6) ... Preparing to unpack .../nfs-kernel-server_1%3a1.3.4-2.5_armel.deb ... Unpacking nfs-kernel-server (1:1.3.4-2.5) over (1:1.3.4-2.1) ... Preparing to unpack .../nfs-common_1%3a1.3.4-2.5_armel.deb ... Unpacking nfs-common (1:1.3.4-2.5) over (1:1.3.4-2.1) ... (Reading database ... 24813 files and directories currently installed.) Removing libtirpc1:armel (0.2.5-1.2+deb9u1) ... Selecting previously unselected package libtirpc-common. (Reading database ... 24806 files and directories currently installed.) Preparing to unpack .../libtirpc-common_1.1.4-0.4_all.deb ... Unpacking libtirpc-common (1.1.4-0.4) ... Selecting previously unselected package libtirpc3:armel. Preparing to unpack .../libtirpc3_1.1.4-0.4_armel.deb ... Unpacking libtirpc3:armel (1.1.4-0.4) ... Preparing to unpack .../liblzma5_5.2.4-1_armel.deb ... Unpacking liblzma5:armel (5.2.4-1) over (5.2.2-1.2+b1) ... Setting up liblzma5:armel (5.2.4-1) ... Setting up libtirpc-common (1.1.4-0.4) ... Setting up libtirpc3:armel (1.1.4-0.4) ... Setting up rpcbind (1.2.5-0.3) ... Installing new version of config file /etc/init.d/rpcbind ... Removing obsolete conffile /etc/init/portmap-wait.conf ... Removing obsolete conffile /etc/init/rpcbind.conf ... Removing obsolete conffile /etc/init/rpcbind-boot.conf ... [ ok ] Stopping RPC port mapper daemon: rpcbind. [ ok ] Starting RPC port mapper daemon: rpcbind. Setting up nfs-common (1:1.3.4-2.5) ... insserv: warning: current start runlevel(s) (2 3 4 5 S) of script `nfs-common' overrides LSB defaults (S). [ ok ] Stopping NFS common utilities: idmapd statd. [ ok ] Starting NFS common utilities: statd idmapd. Setting up nfs-kernel-server (1:1.3.4-2.5) ... [ ok ] Stopping NFS kernel daemon: mountd nfsd. [ ok ] Unexporting directories for NFS kernel daemon.... [warn] Not starting NFS kernel daemon: no exports. ... (warning). Processing triggers for man-db (2.8.5-2) ... Processing triggers for libc-bin (2.28-10) ... root@Cypher:~#
Thanks!...
|
Re: Upgrading to Debian stretch and buster October 12, 2019 05:48PM |
Admin Registered: 13 years ago Posts: 18,545 |
Nuno,
Do you have serial console? or did you set up netconsole? which version of u-boot is on this box?
Try pinging the GoFlex Home before power up. Let it ping a long period like 5 minutes, and observe the ping response and the LED behavior during that time.
or if you have setup static IP for this box
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Do you have serial console? or did you set up netconsole? which version of u-boot is on this box?
Quote
This seemed to complete without any error, but after issuing a reboot command, my GoFlex Home seems not to boot. It is not accessible via the usual SSH connection and I can't ping it, even though the led is a solid green color...
Try pinging the GoFlex Home before power up. Let it ping a long period like 5 minutes, and observe the ping response and the LED behavior during that time.
ping Cypher.local
or if you have setup static IP for this box
ping <IP address>
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Upgrading to Debian stretch and buster October 12, 2019 09:02PM |
Registered: 7 years ago Posts: 366 |
Just wait a little longer, sometimes it might take more than 30 minutes to boot.... You have solid green and it's a good sign.
I did some research on these and it seems the system was running fsck at that time.
And since goflex home / net has failed RTC due to bad battery, the fsck might be often. :P
I did some research on these and it seems the system was running fsck at that time.
And since goflex home / net has failed RTC due to bad battery, the fsck might be often. :P
|
Nuno
Re: Upgrading to Debian stretch and buster October 14, 2019 11:33AM |
When I made the previous post I had already restored a previous working backup.
After you (@bodhi) posted your attempt at helping me (thanks!) I tried to replicate the problem and couldn't. What I did differently was (I think) just upgrade to liblzma5 and reboot before running the "dist-upgrade". After the "dist-upgrade" I though I wouldn't be able to reboot but everything was fine! Go figure!...
I do have the serial console enabled and working just fine (I didn't remember to check it before posting, sorry...) and I am using the latest uBoot. If the problems returns, I'll post any findings...
@daviddyer: You may be right, although I waited for what seemed to be quite a lot of time. Maybe I didn't wait enough...
After you (@bodhi) posted your attempt at helping me (thanks!) I tried to replicate the problem and couldn't. What I did differently was (I think) just upgrade to liblzma5 and reboot before running the "dist-upgrade". After the "dist-upgrade" I though I wouldn't be able to reboot but everything was fine! Go figure!...
I do have the serial console enabled and working just fine (I didn't remember to check it before posting, sorry...) and I am using the latest uBoot. If the problems returns, I'll post any findings...
@daviddyer: You may be right, although I waited for what seemed to be quite a lot of time. Maybe I didn't wait enough...
|
Re: Upgrading to Debian stretch and buster May 09, 2020 12:15PM |
Registered: 5 years ago Posts: 6 |
I don't know if this might be of help anyone but I just upgraded my Lenovo IX2 from stretch to buster without any problems. Just change source.list.d to:
And then:
And at the end don't forget the generate the initramfs using Body's instructions from first post.
deb http://deb.debian.org/debian buster main deb-src http://deb.debian.org/debian buster main deb http://deb.debian.org/debian-security/ buster/updates main deb-src http://deb.debian.org/debian-security/ buster/updates main deb http://deb.debian.org/debian buster-updates main deb-src http://deb.debian.org/debian buster-updates main
And then:
apt-get update apt-get dist-upgrade
And at the end don't forget the generate the initramfs using Body's instructions from first post.
|
Re: Upgrading Debian Distribution April 30, 2023 06:43PM |
Admin Registered: 13 years ago Posts: 18,545 |
I've updated the first post for Debian bookworm upgrade.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Upgrading Debian Distribution May 02, 2023 09:08AM |
Registered: 9 years ago Posts: 54 |
Hey, today I have upgrade my pogoplug from bullseye to bookworm,
everything looks good so far.
However, after a new start of the pogoplug, the startup takes very long,
many times longer than under bullseye.
After a short analysis I noticed that it is probably due to UDEV.
Does anyone have a solution, how I get the start faster again?
Thanks a lot.
everything looks good so far.
However, after a new start of the pogoplug, the startup takes very long,
many times longer than under bullseye.
After a short analysis I noticed that it is probably due to UDEV.
Does anyone have a solution, how I get the start faster again?
Thanks a lot.
Starting hotplug events dispatcher: systemd-udevd. Synthesizing the initial hotplug events (subsystems)...done. Synthesizing the initial hotplug events (devices)...done. Waiting for /dev to be fully populated...[ 25.542486][ T280] orion_wdt: Initial timeout 21 sec [ 26.029522][ T275] usbcore: registered new interface driver uas [ 26.252046][ T274] marvell-cesa f1030000.crypto: CESA device successfully registered [ 26.371330][ T275] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 38.772460][ C0] random: crng init done Timed out for waiting the udev queue being empty. done (timeout). Setting hostname to 'pogoplug-dev'...done. Activating swap:. [ 146.848297][ T449] EXT4-fs (sda1): re-mounted. Opts: (null). Quota mode: none. Will now check root file system:[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sda1 e2fsck 1.47.0 (5-Feb-2023) rootfs: clean, 32538/458752 files, 335429/1835008 blocks . [ 147.043345][ T456] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro. Quota mode: none. Will now check all file systems. Checking all file systems. LABEL=rootfs is mounted Done checking file systems. Log is being saved in /var/log/fsck/checkfs if that location is writable. Cleaning up temporary files...Cleaning /tmp...done. /tmp. Will now mount local filesystems:. Will now activate swapfile swap, if any:done. Checking minimum space in /tmp...done. Cleaning up temporary files.... Starting Setting kernel variables: sysctl. Initializing random number generator...done. Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.3-P1 Copyright 2004-2022 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/52:3b:20:9c:11:51 Sending on LPF/eth0/52:3b:20:9c:11:51 Sending on Socket/fallback DHCPREQUEST for 10.10.172.181 on eth0 to 255.255.255.255 port 67 [ 153.050453][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 153.061126][ T17] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready DHCPREQUEST for 10.10.172.181 on eth0 to 255.255.255.255 port 67 DHCPACK of 10.10.172.181 from 10.10.172.1 bound to 10.10.172.181 -- renewal in 36454 seconds. done. Starting RPC port mapper daemon: rpcbind. Starting NFS common utilities: statd idmapd. Cleaning up temporary files.... INIT: Entering runlevel: 2 Using makefile-style concurrent boot in runlevel 2. Not starting NFS kernel daemon: no exports ... (warning). Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 968 (syslogd) . Starting system message bus: dbus. Starting LCDd: LCDd. Starting NTP server: ntpd1970-01-01T01:02:37 ntpd[1011]: INIT: ntpd ntpsec-1.2.2: Starting 1970-01-01T01:02:37 ntpd[1011]: INIT: Command line: /usr/sbin/ntpd -p /var/run/ntpd.pid -g -u 104:106 . Starting NTP server: ntpd. Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 992 (klogd) . Starting Squeezebox client: squeezelite. Starting OpenBSD Secure Shell server: sshd. Running local boot scripts (/etc/rc.local) . Debian GNU/Linux 12 pogoplug-dev ttyS0 pogoplug-dev login:
|
Re: Upgrading Debian Distribution May 02, 2023 02:53PM |
Admin Registered: 13 years ago Posts: 18,545 |
droidbox,
It might not be udev. It could be urandom
Reboot and see if it gets faster. Is this the Pogoplug E02?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
It might not be udev. It could be urandom
[ 38.772460][ C0] random: crng init done
Reboot and see if it gets faster. Is this the Pogoplug E02?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Upgrading Debian Distribution May 12, 2023 08:47AM |
Registered: 9 years ago Posts: 54 |
|
Re: Upgrading Debian Distribution May 12, 2023 03:11PM |
Admin Registered: 13 years ago Posts: 18,545 |
> Yes it is a Pogoplug E02.
Then it is unlikely related to urandom. Post the output of:
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Then it is unlikely related to urandom. Post the output of:
dmesg cat /etc/fstab cat /etc/rc.local
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Upgrading Debian Distribution May 12, 2023 05:01PM |
Registered: 9 years ago Posts: 54 |
root@pogoplug-dev:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.13.6-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 PREEMPT Sat Jul 31 22:10:39 PDT 2021 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: CloudEngines Pogoplug E02 [ 0.000000] printk: bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] On node 0 totalpages: 65536 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65536 pages, LIFO batch:15 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000] Memory: 240508K/262144K available (11264K kernel code, 1553K rwdata, 4272K rodata, 1024K init, 309K bss, 21636K reserved, 0K cma-reserved) [ 0.000000] random: get_random_u32 called from ____cache_alloc+0x408/0x7b4 with crng_init=0 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000002] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008609] Switching to timer-based delay loop, resolution 5ns [ 0.016122] Console: colour dummy device 80x30 [ 0.021394] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.032735] pid_max: default: 32768 minimum: 301 [ 0.038482] LSM: Security Framework initializing [ 0.044040] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.052163] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.062143] CPU: Testing write buffer coherency: ok [ 0.070257] Setting up static identity map for 0x100000 - 0x100058 [ 0.077461] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.083728] rcu: Hierarchical SRCU implementation. [ 0.090745] devtmpfs: initialized [ 0.100470] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.111176] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.156178] prandom32: self test passed (less than 6 bits correlated) [ 0.163414] prandom: seed boundary self test passed [ 0.173251] prandom: 100 self tests passed [ 0.178083] pinctrl core: initialized pinctrl subsystem [ 0.185717] NET: Registered protocol family 16 [ 0.191775] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.200411] audit: initializing netlink subsys (disabled) [ 0.207949] thermal_sys: Registered thermal governor 'step_wise' [ 0.208337] audit: type=2000 audit(0.190:1): state=initialized audit_enabled=0 res=1 [ 0.223788] cpuidle: using governor ladder [ 0.228762] cpuidle: using governor menu [ 0.233902] Feroceon L2: Enabling L2 [ 0.238236] Feroceon L2: Cache support initialised. [ 0.252354] No ATAGs? [ 2.568615] random: fast init done [ 5.146607] "cryptomgr_test" (39) uses obsolete ecb(arc4) skcipher [ 5.180196] wait_for_initramfs() called before rootfs_initcalls [ 5.378720] raid6: int32x8 gen() 108 MB/s [ 5.548687] raid6: int32x8 xor() 68 MB/s [ 5.718728] raid6: int32x4 gen() 109 MB/s [ 5.888690] raid6: int32x4 xor() 71 MB/s [ 6.058620] raid6: int32x2 gen() 137 MB/s [ 6.228673] raid6: int32x2 xor() 85 MB/s [ 6.398699] raid6: int32x1 gen() 97 MB/s [ 6.568679] raid6: int32x1 xor() 58 MB/s [ 6.573676] raid6: using algorithm int32x2 gen() 137 MB/s [ 6.579813] raid6: .... xor() 85 MB/s, rmw enabled [ 6.585326] raid6: using intx1 recovery algorithm [ 6.591053] vgaarb: loaded [ 6.595047] SCSI subsystem initialized [ 6.599792] libata version 3.00 loaded. [ 6.600086] usbcore: registered new interface driver usbfs [ 6.606355] usbcore: registered new interface driver hub [ 6.612493] usbcore: registered new device driver usb [ 6.618473] pps_core: LinuxPPS API ver. 1 registered [ 6.624186] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 6.634102] PTP clock support registered [ 6.640663] clocksource: Switched to clocksource orion_clocksource [ 6.751375] VFS: Disk quotas dquot_6.6.0 [ 6.756120] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 6.791965] NET: Registered protocol family 2 [ 6.797216] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 6.821756] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 6.840720] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 6.849155] TCP bind hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 6.880742] TCP: Hash tables configured (established 2048 bind 2048) [ 6.888101] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear) [ 6.910774] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 6.918066] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 6.940953] NET: Registered protocol family 1 [ 6.950987] RPC: Registered named UNIX socket transport module. [ 6.957645] RPC: Registered udp transport module. [ 6.970686] RPC: Registered tcp transport module. [ 6.976122] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 7.000686] PCI: CLS 0 bytes, default 32 [ 7.005642] NetWinder Floating Point Emulator V0.97 (double precision) [ 8.392146] Initialise system trusted keyrings [ 8.397372] Key type blacklist registered [ 8.402441] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 8.409740] zbud: loaded [ 8.414585] NFS: Registering the id_resolver key type [ 8.420393] Key type id_resolver registered [ 8.425376] Key type id_legacy registered [ 8.430152] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 8.437618] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 8.445802] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 8.453191] jffs2: version 2.2. (NAND) (SUMMARY) \xc2\xa9 2001-2006 Red Hat, Inc. [ 8.461535] fuse: init (API version 7.34) [ 8.466686] orangefs_debugfs_init: called with debug mask: :none: :0: [ 8.474109] orangefs_init: module version upstream loaded [ 8.480236] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 8.590690] xor: measuring software checksum speed [ 8.605135] arm4regs : 1113 MB/sec [ 8.625027] 8regs : 667 MB/sec [ 8.640291] 32regs : 971 MB/sec [ 8.645404] xor: using function: arm4regs (1113 MB/sec) [ 8.651406] async_tx: api initialized (async) [ 8.656492] Key type asymmetric registered [ 8.661345] Asymmetric key parser 'x509' registered [ 8.666998] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 8.675253] io scheduler bfq registered [ 8.879396] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 8.889778] mv_xor f1060800.xor: Marvell shared XOR driver [ 8.951800] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 8.962548] mv_xor f1060900.xor: Marvell shared XOR driver [ 9.031768] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 9.042770] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 9.051315] printk: console [ttyS0] disabled [ 9.056391] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A [ 9.066236] printk: console [ttyS0] enabled [ 9.076090] printk: bootconsole [earlycon0] disabled [ 9.096668] loop: module loaded [ 9.101903] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it [ 9.111357] ONFI parameter recovery failed, aborting [ 9.117058] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 9.124166] nand: Hynix NAND 128MiB 3,3V 8-bit [ 9.129334] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 9.137970] Scanning device for bad blocks [ 9.165480] Bad eraseblock 193 at 0x000001820000 [ 9.244718] Bad eraseblock 825 at 0x000006720000 [ 9.273299] 4 fixed-partitions partitions found on MTD device orion_nand [ 9.280762] Creating 4 MTD partitions on "orion_nand": [ 9.286629] 0x000000000000-0x000000100000 : "u-boot" [ 9.293939] 0x000000100000-0x000000600000 : "uImage" [ 9.301223] 0x000000500000-0x000002a00000 : "pogoplug" [ 9.308784] 0x000002500000-0x000009100000 : "root" [ 9.314352] mtd: partition "root" extends beyond the end of device "orion_nand" -- size truncated to 0x5b00000 [ 9.327520] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 9.336137] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 9.347748] libphy: Fixed MDIO Bus: probed [ 9.354170] libphy: orion_mdio_bus: probed [ 9.360505] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 10.121851] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 52:3b:20:9c:11:51 [ 10.131505] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 10.138802] ehci-pci: EHCI PCI platform driver [ 10.144056] ehci-orion: EHCI orion driver [ 10.149004] orion-ehci f1050000.ehci: EHCI Host Controller [ 10.155288] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 10.163892] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 10.190706] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 10.197773] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 10.206819] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.214805] usb usb1: Product: EHCI Host Controller [ 10.220408] usb usb1: Manufacturer: Linux 5.13.6-kirkwood-tld-1 ehci_hcd [ 10.227866] usb usb1: SerialNumber: f1050000.ehci [ 10.234038] hub 1-0:1.0: USB hub found [ 10.238564] hub 1-0:1.0: 1 port detected [ 10.244089] usbcore: registered new interface driver usb-storage [ 10.251330] mousedev: PS/2 mouse device common for all mice [ 10.530696] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 10.732402] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=77.64 [ 10.741363] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 10.749266] usb 1-1: Product: USB2.0 Hub [ 10.754877] hub 1-1:1.0: USB hub found [ 10.759782] hub 1-1:1.0: 4 ports detected [ 11.080690] usb 1-1.4: new high-speed USB device number 3 using orion-ehci [ 11.231652] usb 1-1.4: New USB device found, idVendor=0781, idProduct=5571, bcdDevice= 1.26 [ 11.240783] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 11.248857] usb 1-1.4: Product: Firebird USB Flash Drive [ 11.254922] usb 1-1.4: Manufacturer: SanDisk [ 11.259931] usb 1-1.4: SerialNumber: 4C532000031011101542 [ 11.266856] usb-storage 1-1.4:1.0: USB Mass Storage device detected [ 11.274498] scsi host0: usb-storage 1-1.4:1.0 [ 11.290701] rtc-mv f1010300.rtc: internal RTC not ticking [ 11.297034] i2c /dev entries driver [ 11.301950] device-mapper: uevent: version 1.0.3 [ 11.307601] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com [ 11.317272] device-mapper: multipath round-robin: version 1.2.0 loaded [ 11.324608] device-mapper: multipath queue-length: version 0.2.0 loaded [ 11.331988] device-mapper: multipath service-time: version 0.3.0 loaded [ 11.339408] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 11.346255] device-mapper: raid: Loading target version 1.15.1 [ 11.354341] hid: raw HID events driver (C) Jiri Kosina [ 11.360555] drop_monitor: Initializing network drop monitor service [ 11.368103] NET: Registered protocol family 10 [ 11.374713] Segment Routing with IPv6 [ 11.379105] RPL Segment Routing with IPv6 [ 11.384027] NET: Registered protocol family 17 [ 11.389454] Key type dns_resolver registered [ 11.395052] registered taskstats version 1 [ 11.399882] Loading compiled-in X.509 certificates [ 11.405893] zswap: loaded using pool lzo/zbud [ 11.411419] Key type ._fscrypt registered [ 11.416156] Key type .fscrypt registered [ 11.420875] Key type fscrypt-provisioning registered [ 11.428788] Key type big_key registered [ 11.437535] Key type encrypted registered [ 11.445764] Waiting 10 sec before mounting root device... [ 12.331639] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Fit 1.26 PQ: 0 ANSI: 5 [ 12.342212] sd 0:0:0:0: [sda] 15633408 512-byte logical blocks: (8.00 GB/7.45 GiB) [ 12.352689] sd 0:0:0:0: [sda] Write Protect is off [ 12.358234] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00 [ 12.358936] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 12.375561] sda: sda1 sda2 [ 12.382941] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 21.610692] md: Waiting for all devices to be available before autodetect [ 21.618238] md: If you don't use raid, use raid=noautodetect [ 21.624648] md: Autodetecting RAID arrays. [ 21.629464] md: autorun ... [ 21.632988] md: ... autorun DONE. [ 21.638716] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 21.656202] EXT4-fs (sda1): INFO: recovery required on readonly filesystem [ 21.663869] EXT4-fs (sda1): write access will be enabled during recovery [ 21.890547] EXT4-fs (sda1): recovery complete [ 21.898690] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none. [ 21.908852] VFS: Mounted root (ext3 filesystem) readonly on device 8:1. [ 21.932874] devtmpfs: mounted [ 21.939687] Freeing unused kernel memory: 1024K [ 21.945776] Checked W+X mappings: passed, no W+X pages found [ 21.952222] Run /sbin/init as init process [ 21.957040] with arguments: [ 21.957049] /sbin/init [ 21.957058] with environment: [ 21.957065] HOME=/ [ 21.957072] TERM=linux [ 22.999593] ecc_sw_hamming_correct: uncorrectable ECC error [ 23.006000] blk_update_request: I/O error, dev mtdblock0, sector 2040 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 [ 23.017972] ecc_sw_hamming_correct: uncorrectable ECC error [ 23.024311] blk_update_request: I/O error, dev mtdblock0, sector 2040 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 23.035702] Buffer I/O error on dev mtdblock0, logical block 255, async page read [ 25.995200] orion_wdt: Initial timeout 21 sec [ 26.632050] marvell-cesa f1030000.crypto: CESA device successfully registered [ 26.661387] usbcore: registered new interface driver uas [ 26.866727] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 27.290781] random: crng init done [ 147.297641] EXT4-fs (sda1): re-mounted. Opts: (null). Quota mode: none. [ 147.487419] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro. Quota mode: none. [ 153.371991] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 153.382643] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready root@pogoplug-dev:~#
root@pogoplug-dev:~# cat /etc/fstab # /etc/fstab: static file system information. # # <file system> <mount point> <type> <options> <dump> <pass> LABEL=rootfs / ext3 noatime,errors=remount-ro 0 1 tmpfs /tmp tmpfs defaults 0 0
root@pogoplug-dev:~# cat /etc/rc.local
#!/bin/sh -e
#
# rc.local
#
# This script is executed at the end of each multiuser runlevel.
# Make sure that the script will "exit 0" on success or any other
# value on error.
#
# In order to enable or disable this script just change the execution
# bits.
#
# By default this script does nothing.
# generate SSH key on 1st boot and start SSH server if not already running
ssh-keygen -A
if ! pgrep -x sshd >/dev/null ; then
/etc/init.d/ssh start
fi
# turn on LED
if [ -d /sys/class/leds/status:green:health ]; then
echo default-on > /sys/class/leds/status:green:health/trigger
if [ -d /sys/class/leds/status:orange:fault ]; then
echo none > /sys/class/leds/status:orange:fault/trigger
fi
if [ -d /sys/class/leds/status:blue:health ]; then
echo none > /sys/class/leds/status:blue:health/trigger
fi
fi
if [ -d /sys/class/leds/dockstar:green:health ]; then
echo default-on > /sys/class/leds/dockstar:green:health/trigger
echo none > /sys/class/leds/dockstar:orange:misc/trigger
fi
if [ -d /sys/class/leds/plug:green:health ]; then
echo default-on > /sys/class/leds/plug:green:health/trigger
if [ -d /sys/class/leds/plug:red:misc ]; then
echo none > /sys/class/leds/plug:red:misc/trigger
fi
fi
if [ -d /sys/class/leds/power:blue ]; then
echo default-on > /sys/class/leds/power:blue/trigger
### echo default-on > /sys/class/leds/otb:blue/trigger
echo none > /sys/class/leds/power:red/trigger
fi
if [ -d /sys/class/leds/usb1:blue ]; then
echo usb-host > /sys/class/leds/usb1\:blue/trigger
fi
if [ -d /sys/class/leds/usb2:blue ]; then
echo usb-host > /sys/class/leds/usb2\:blue/trigger
fi
if [ -d /sys/class/leds/usb3:blue ]; then
echo usb-host > /sys/class/leds/usb3\:blue/trigger
fi
if [ -d /sys/class/leds/usb4:blue ]; then
echo usb-host > /sys/class/leds/usb4\:blue/trigger
fi
if [ -d /sys/class/leds/nsa325:green:sys ]; then
echo default-on > /sys/class/leds/nsa325:green:sys/trigger
echo none > /sys/class/leds/nsa325:orange:sys/trigger
fi
if [ -d /sys/class/leds/nsa325:green:sata1 ]; then
echo ide-disk1 > /sys/class/leds/nsa325:green:sata1/trigger
fi
if [ -d /sys/class/leds/nsa325:green:sata2 ]; then
echo ide-disk2 > /sys/class/leds/nsa325:green:sata2/trigger
fi
if [ -d /sys/class/leds/nsa325:green:usb ]; then
echo usb-host > /sys/class/leds/nsa325\:green\:usb/trigger
fi
exit 0
|
Re: Upgrading Debian Distribution May 12, 2023 06:47PM |
Admin Registered: 13 years ago Posts: 18,545 |
There is something odd here:
That rootfs should not have been re-mounted. Should be just mounted.
===
By the way, your system booting is not set up correctly. But I will tell you what to correct after I see the log.
Power up, interrupt serial console count down and
Please post the entire serial boot log.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
[ 27.290781] random: crng init done [ 147.297641] EXT4-fs (sda1): re-mounted. Opts: (null). Quota mode: none.
That rootfs should not have been re-mounted. Should be just mounted.
===
By the way, your system booting is not set up correctly. But I will tell you what to correct after I see the log.
Power up, interrupt serial console count down and
printenv boot
Please post the entire serial boot log.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Upgrading Debian Distribution May 13, 2023 01:47PM |
Registered: 9 years ago Posts: 54 |
PogoE02> printenv arcNumber=2097 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-pogo_e02.dtb ethact=egiga0 ethaddr=52:3b:20:9c:11:51 if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 machid=0x831 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=3 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15 Environment size: 2844/131068 bytes
|
Re: Upgrading Debian Distribution May 13, 2023 01:48PM |
Registered: 9 years ago Posts: 54 |
bodhi Wrote:
-------------------------------------------------------
> There is something odd here:
>
>
> That rootfs should not have been re-mounted.
> Should be just mounted.
>
But how can I prevent this?
-------------------------------------------------------
> There is something odd here:
>
>
> [ 27.290781] random: crng init done > [ 147.297641] EXT4-fs (sda1): re-mounted. Opts: > (null). Quota mode: none. >>
> That rootfs should not have been re-mounted.
> Should be just mounted.
>
But how can I prevent this?
|
Re: Upgrading Debian Distribution May 13, 2023 02:51PM |
Admin Registered: 13 years ago Posts: 18,545 |
> There is something odd here:
>
>
> That rootfs should not have been re-mounted.
> Should be just mounted.
>
>
> ===
>
> By the way, your system booting is not set up
> correctly. But I will tell you what to correct
> after I see the log.
>
> Power up, interrupt serial console count down and
>
>
> Please post the entire serial boot log.
I might be able to see why if you post the log.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
>
>
> [ 27.290781] random: crng init done > [ 147.297641] EXT4-fs (sda1): re-mounted. Opts: > (null). Quota mode: none. >>
> That rootfs should not have been re-mounted.
> Should be just mounted.
>
>
> ===
>
> By the way, your system booting is not set up
> correctly. But I will tell you what to correct
> after I see the log.
>
> Power up, interrupt serial console count down and
>
>
> printenv > boot >>
> Please post the entire serial boot log.
I might be able to see why if you post the log.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Upgrading Debian Distribution May 13, 2023 02:55PM |
Registered: 9 years ago Posts: 54 |
|
Re: Upgrading Debian Distribution May 13, 2023 03:02PM |
Admin Registered: 13 years ago Posts: 18,545 |
droidbox,
> sorry bodhi, but where can i find the serial log?
The serial console log is what's on your terminal when you connect serial console and observe the boot progress.
Power up, interrupt serial console count down and
Wait until it boot to the Debian login promp. And then copy and paste what's on the terminal (from u-boot banner until the login prompt).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> sorry bodhi, but where can i find the serial log?
The serial console log is what's on your terminal when you connect serial console and observe the boot progress.
Power up, interrupt serial console count down and
printenv boot
Wait until it boot to the Debian login promp. And then copy and paste what's on the terminal (from u-boot banner until the login prompt).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Upgrading Debian Distribution May 13, 2023 03:11PM |
Registered: 9 years ago Posts: 54 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700)
Pogo E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
Hit any key to stop autoboot: 0
PogoE02> printenv
arcNumber=2097
bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec
bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootdev=usb
device=0:1
devices=usb ide mmc
disks=0 1 2 3
dtb_file=/boot/dts/kirkwood-pogo_e02.dtb
ethact=egiga0
ethaddr=52:3b:20:9c:11:51
if_netconsole=ping $serverip
ipaddr=192.168.0.231
led_error=orange blinking
led_exit=green off
led_init=green blinking
load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file
load_dtb_addr=0x1c00000
load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd
load_initrd_addr=0x1100000
load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage
load_uimage_addr=0x800000
machid=0x831
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
partition=nand0,2
preboot_nc=run if_netconsole start_netconsole
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done
serverip=192.168.0.220
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=3 $mtdparts $custom_params
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
uenv_addr=0x810000
uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize
uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done;
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi
usb_ready_retry=15
Environment size: 2844/131068 bytes
PogoE02> boot
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices...
Use USB retry period from the environment: 15 second(s)
1 Storage Device(s) found
Unknown command 'ide' - try 'help'
Unknown command 'mmc' - try 'help'
Partition Map for USB device 0 -- Partition Type: DOS
Part Start Sector Num Sectors UUID Type
1 2048 14680064 068ddb4f-01 83
2 14682112 951296 068ddb4f-02 82
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **
Unknown command 'ide' - try 'help'
Unknown command 'mmc' - try 'help'
running scan_disk ...
Scan device usb
device usb 0:1
1 bytes read in 723 ms (0 Bytes/s)
Found bootable drive on usb 0
loading uImage ...
5446002 bytes read in 1084 ms (4.8 MiB/s)
loading uInitrd ...
9671091 bytes read in 1089 ms (8.5 MiB/s)
loading DTB /boot/dts/kirkwood-pogo_e02.dtb ...
10114 bytes read in 3782 ms (2 KiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-5.13.6-kirkwood-tld-1
Created: 2023-04-28 20:56:31 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5445938 Bytes = 5.2 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-5.13.6-kirkwood-tld-1
Created: 2021-09-24 1:06:32 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9671027 Bytes = 9.2 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
Booting using the fdt blob at 0x1c00000
Loading Kernel Image ... OK
Loading Ramdisk to 0f1d6000, end 0fb0f173 ... OK
Loading Device Tree to 0f1d0000, end 0f1d5781 ... OK
Using machid 0x831 from environment
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 5.13.6-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 PREEMPT Sat Jul 31 22:10:39 PDT 2021
[ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: CloudEngines Pogoplug E02
[ 0.000000][ T0] printk: bootconsole [earlycon0] enabled
[ 0.000000][ T0] Memory policy: Data cache writeback
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 65024
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10
[ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 240508K/262144K available (11264K kernel code, 1553K rwdata, 4272K rodata, 1024K init, 309K bss, 21636K reserved, 0K cma-reserved)
[ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x408/0x7b4 with crng_init=0
[ 0.000000][ T0] trace event string verifier disabled
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000002][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.008609][ T0] Switching to timer-based delay loop, resolution 5ns
[ 0.016123][ T0] Console: colour dummy device 80x30
[ 0.021395][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000)
[ 0.032735][ T0] pid_max: default: 32768 minimum: 301
[ 0.038483][ T0] LSM: Security Framework initializing
[ 0.044041][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.052163][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.062144][ T0] CPU: Testing write buffer coherency: ok
[ 0.070273][ T1] Setting up static identity map for 0x100000 - 0x100058
[ 0.077479][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2
[ 0.083746][ T1] rcu: Hierarchical SRCU implementation.
[ 0.090762][ T1] devtmpfs: initialized
[ 0.100484][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.111193][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.156192][ T1] prandom32: self test passed (less than 6 bits correlated)
[ 0.163431][ T1] prandom: seed boundary self test passed
[ 0.173269][ T1] prandom: 100 self tests passed
[ 0.178100][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.185731][ T1] NET: Registered protocol family 16
[ 0.191793][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.200431][ T1] audit: initializing netlink subsys (disabled)
[ 0.207977][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.208372][ T16] audit: type=2000 audit(0.190:1): state=initialized audit_enabled=0 res=1
[ 0.223826][ T1] cpuidle: using governor ladder
[ 0.228799][ T1] cpuidle: using governor menu
[ 0.233947][ T1] Feroceon L2: Enabling L2
[ 0.238280][ T1] Feroceon L2: Cache support initialised.
[ 0.252402][ T1] No ATAGs?
[ 2.568616][ C0] random: fast init done
[ 5.146644][ T39] "cryptomgr_test" (39) uses obsolete ecb(arc4) skcipher
[ 5.180251][ T59] wait_for_initramfs() called before rootfs_initcalls
[ 5.378717][ T1] raid6: int32x8 gen() 108 MB/s
[ 5.548641][ T1] raid6: int32x8 xor() 68 MB/s
[ 5.718770][ T1] raid6: int32x4 gen() 109 MB/s
[ 5.888768][ T1] raid6: int32x4 xor() 71 MB/s
[ 6.058692][ T1] raid6: int32x2 gen() 138 MB/s
[ 6.228640][ T1] raid6: int32x2 xor() 85 MB/s
[ 6.398699][ T1] raid6: int32x1 gen() 98 MB/s
[ 6.568676][ T1] raid6: int32x1 xor() 59 MB/s
[ 6.573668][ T1] raid6: using algorithm int32x2 gen() 138 MB/s
[ 6.579804][ T1] raid6: .... xor() 85 MB/s, rmw enabled
[ 6.585317][ T1] raid6: using intx1 recovery algorithm
[ 6.591042][ T1] vgaarb: loaded
[ 6.595038][ T1] SCSI subsystem initialized
[ 6.600074][ T1] usbcore: registered new interface driver usbfs
[ 6.606346][ T1] usbcore: registered new interface driver hub
[ 6.612485][ T1] usbcore: registered new device driver usb
[ 6.618465][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 6.624178][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 6.634094][ T1] PTP clock support registered
[ 6.640654][ T1] clocksource: Switched to clocksource orion_clocksource
[ 6.751364][ T1] VFS: Disk quotas dquot_6.6.0
[ 6.756104][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 6.791972][ T1] NET: Registered protocol family 2
[ 6.797226][ T1] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 6.821748][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 6.840713][ T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 6.849147][ T1] TCP bind hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 6.880735][ T1] TCP: Hash tables configured (established 2048 bind 2048)
[ 6.888101][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 6.910766][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 6.918057][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 6.940939][ T1] NET: Registered protocol family 1
[ 6.950981][ T1] RPC: Registered named UNIX socket transport module.
[ 6.957636][ T1] RPC: Registered udp transport module.
[ 6.970676][ T1] RPC: Registered tcp transport module.
[ 6.976104][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 7.000678][ T1] PCI: CLS 0 bytes, default 32
[ 7.005630][ T1] NetWinder Floating Point Emulator V0.97 (double precision)
[ 8.392038][ T1] Initialise system trusted keyrings
[ 8.397278][ T1] Key type blacklist registered
[ 8.402346][ T1] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[ 8.409645][ T1] zbud: loaded
[ 8.414489][ T1] NFS: Registering the id_resolver key type
[ 8.420303][ T1] Key type id_resolver registered
[ 8.425280][ T1] Key type id_legacy registered
[ 8.430054][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 8.437522][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 8.445706][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 8.453095][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 8.461438][ T1] fuse: init (API version 7.34)
[ 8.466579][ T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 8.473996][ T1] orangefs_init: module version upstream loaded
[ 8.480131][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled
[ 8.592095][ T1] xor: measuring software checksum speed
[ 8.606545][ T1] arm4regs : 1113 MB/sec
[ 8.626475][ T1] 8regs : 667 MB/sec
[ 8.641775][ T1] 32regs : 971 MB/sec
[ 8.646856][ T1] xor: using function: arm4regs (1113 MB/sec)
[ 8.652855][ T1] async_tx: api initialized (async)
[ 8.657948][ T1] Key type asymmetric registered
[ 8.662806][ T1] Asymmetric key parser 'x509' registered
[ 8.668463][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[ 8.676699][ T1] io scheduler bfq registered
[ 8.880818][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 8.891205][ T1] mv_xor f1060800.xor: Marvell shared XOR driver
[ 8.961762][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 8.972516][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 9.041756][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 9.052748][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 9.061291][ T1] printk: console [ttyS0] disabled
[ 9.066367][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A
[ 9.076214][ T1] printk: console [ttyS0] enabled
[ 9.076214][ T1] printk: console [ttyS0] enabled
[ 9.086067][ T1] printk: bootconsole [earlycon0] disabled
[ 9.086067][ T1] printk: bootconsole [earlycon0] disabled
[ 9.106642][ T1] loop: module loaded
[ 9.111880][ T1] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it
[ 9.121332][ T1] ONFI parameter recovery failed, aborting
[ 9.127034][ T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[ 9.134143][ T1] nand: Hynix NAND 128MiB 3,3V 8-bit
[ 9.139311][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 9.147946][ T1] Scanning device for bad blocks
[ 9.175435][ T1] Bad eraseblock 193 at 0x000001820000
[ 9.254724][ T1] Bad eraseblock 825 at 0x000006720000
[ 9.283290][ T1] 4 fixed-partitions partitions found on MTD device orion_nand
[ 9.290755][ T1] Creating 4 MTD partitions on "orion_nand":
[ 9.296625][ T1] 0x000000000000-0x000000100000 : "u-boot"
[ 9.303926][ T1] 0x000000100000-0x000000600000 : "uImage"
[ 9.311215][ T1] 0x000000500000-0x000002a00000 : "pogoplug"
[ 9.318773][ T1] 0x000002500000-0x000009100000 : "root"
[ 9.324334][ T1] mtd: partition "root" extends beyond the end of device "orion_nand" -- size truncated to 0x5b00000
[ 9.337499][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 9.346122][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 9.357731][ T1] libphy: Fixed MDIO Bus: probed
[ 9.364143][ T1] libphy: orion_mdio_bus: probed
[ 9.370448][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 10.131842][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 52:3b:20:9c:11:51
[ 10.141495][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 10.148786][ T1] ehci-pci: EHCI PCI platform driver
[ 10.154040][ T1] ehci-orion: EHCI orion driver
[ 10.158992][ T1] orion-ehci f1050000.ehci: EHCI Host Controller
[ 10.165274][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 10.173880][ T1] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[ 10.200697][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 10.207770][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13
[ 10.216820][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 10.224807][ T1] usb usb1: Product: EHCI Host Controller
[ 10.230411][ T1] usb usb1: Manufacturer: Linux 5.13.6-kirkwood-tld-1 ehci_hcd
[ 10.237869][ T1] usb usb1: SerialNumber: f1050000.ehci
[ 10.244041][ T1] hub 1-0:1.0: USB hub found
[ 10.248566][ T1] hub 1-0:1.0: 1 port detected
[ 10.254090][ T1] usbcore: registered new interface driver usb-storage
[ 10.261330][ T1] mousedev: PS/2 mouse device common for all mice
[ 10.540687][ T17] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 10.742391][ T17] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=77.64
[ 10.751347][ T17] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 10.759259][ T17] usb 1-1: Product: USB2.0 Hub
[ 10.764868][ T17] hub 1-1:1.0: USB hub found
[ 10.769644][ T17] hub 1-1:1.0: 4 ports detected
[ 11.090681][ T17] usb 1-1.4: new high-speed USB device number 3 using orion-ehci
[ 11.241639][ T17] usb 1-1.4: New USB device found, idVendor=0781, idProduct=5571, bcdDevice= 1.26
[ 11.250776][ T17] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 11.258851][ T17] usb 1-1.4: Product: Firebird USB Flash Drive
[ 11.264919][ T17] usb 1-1.4: Manufacturer: SanDisk
[ 11.269925][ T17] usb 1-1.4: SerialNumber: 4C532000031011101542
[ 11.276842][ T17] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[ 11.284476][ T17] scsi host0: usb-storage 1-1.4:1.0
[ 11.290706][ T1] rtc-mv f1010300.rtc: internal RTC not ticking
[ 11.297044][ T1] i2c /dev entries driver
[ 11.301948][ T1] device-mapper: uevent: version 1.0.3
[ 11.307599][ T1] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com
[ 11.317277][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 11.324614][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 11.331996][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 11.339407][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 11.346256][ T1] device-mapper: raid: Loading target version 1.15.1
[ 11.354340][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 11.360547][ T1] drop_monitor: Initializing network drop monitor service
[ 11.368096][ T1] NET: Registered protocol family 10
[ 11.374691][ T1] Segment Routing with IPv6
[ 11.379079][ T1] RPL Segment Routing with IPv6
[ 11.383999][ T1] NET: Registered protocol family 17
[ 11.389428][ T1] Key type dns_resolver registered
[ 11.395022][ T1] registered taskstats version 1
[ 11.399855][ T1] Loading compiled-in X.509 certificates
[ 11.405864][ T1] zswap: loaded using pool lzo/zbud
[ 11.411385][ T1] Key type ._fscrypt registered
[ 11.416122][ T1] Key type .fscrypt registered
[ 11.420847][ T1] Key type fscrypt-provisioning registered
[ 11.428765][ T1] Key type big_key registered
[ 11.437494][ T1] Key type encrypted registered
[ 11.445707][ T1] Waiting 10 sec before mounting root device...
[ 12.331625][ T7] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Fit 1.26 PQ: 0 ANSI: 5
[ 12.342202][ T80] sd 0:0:0:0: [sda] 15633408 512-byte logical blocks: (8.00 GB/7.45 GiB)
[ 12.351300][ T80] sd 0:0:0:0: [sda] Write Protect is off
[ 12.357563][ T80] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 12.373547][ T80] sda: sda1 sda2
[ 12.381055][ T80] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 21.610685][ T1] md: Waiting for all devices to be available before autodetect
[ 21.618217][ T1] md: If you don't use raid, use raid=noautodetect
[ 21.624631][ T1] md: Autodetecting RAID arrays.
[ 21.629448][ T1] md: autorun ...
[ 21.632971][ T1] md: ... autorun DONE.
[ 21.638703][ T1] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 21.674939][ T1] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none.
[ 21.685164][ T1] VFS: Mounted root (ext3 filesystem) readonly on device 8:1.
[ 21.702237][ T1] devtmpfs: mounted
[ 21.709055][ T1] Freeing unused kernel memory: 1024K
[ 21.715149][ T1] Checked W+X mappings: passed, no W+X pages found
[ 21.721596][ T1] Run /sbin/init as init process
INIT: version 3.06 booting
Using makefile-style concurrent boot in runlevel S.
[ 22.714656][ T171] ecc_sw_hamming_correct: uncorrectable ECC error
[ 22.721101][ T171] blk_update_request: I/O error, dev mtdblock0, sector 2040 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[ 22.733040][ T171] ecc_sw_hamming_correct: uncorrectable ECC error
[ 22.739350][ T171] blk_update_request: I/O error, dev mtdblock0, sector 2040 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 22.750748][ T171] Buffer I/O error on dev mtdblock0, logical block 255, async page read
Starting hotplug events dispatcher: systemd-udevd.
Synthesizing the initial hotplug events (subsystems)...done.
Synthesizing the initial hotplug events (devices)...done.
Waiting for /dev to be fully populated...[ 25.581072][ T274] orion_wdt: Initial timeout 21 sec
[ 26.271804][ T283] marvell-cesa f1030000.crypto: CESA device successfully registered
[ 26.321301][ T277] usbcore: registered new interface driver uas
[ 26.528833][ T277] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 30.815249][ C0] random: crng init done
---- > PAUSE < ----
Timed out for waiting the udev queue being empty.
done (timeout).
Setting hostname to 'pogoplug-dev'...done.
Activating swap:.
[ 146.762117][ T449] EXT4-fs (sda1): re-mounted. Opts: (null). Quota mode: none.
Will now check root file system:[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sda1
e2fsck 1.47.0 (5-Feb-2023)
rootfs: clean, 32544/458752 files, 335504/1835008 blocks
.
[ 146.981058][ T457] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro. Quota mode: none.
Will now check all file systems.
Checking all file systems.
LABEL=rootfs is mounted
Done checking file systems.
Log is being saved in /var/log/fsck/checkfs if that location is writable.
Cleaning up temporary files...Cleaning /tmp...done.
/tmp.
Will now mount local filesystems:.
Will now activate swapfile swap, if any:done.
Checking minimum space in /tmp...done.
Cleaning up temporary files....
Starting Setting kernel variables: sysctl.
Initializing random number generator...done.
Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.3-P1
Copyright 2004-2022 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/52:3b:20:9c:11:51
Sending on LPF/eth0/52:3b:20:9c:11:51
Sending on Socket/fallback
DHCPREQUEST for 10.10.172.181 on eth0 to 255.255.255.255 port 67
[ 152.956395][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 152.967050][ T17] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
DHCPREQUEST for 10.10.172.181 on eth0 to 255.255.255.255 port 67
DHCPACK of 10.10.172.181 from 10.10.172.1
bound to 10.10.172.181 -- renewal in 41574 seconds.
done.
Starting RPC port mapper daemon: rpcbind.
Starting NFS common utilities: statd idmapd.
Cleaning up temporary files....
INIT: Entering runlevel: 2
Using makefile-style concurrent boot in runlevel 2.
Not starting NFS kernel daemon: no exports ... (warning).
Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
969 (syslogd)
.
Starting system message bus: dbus.
Starting LCDd: LCDd.
Starting NTP server: ntpd1970-01-01T01:02:35 ntpd[1012]: INIT: ntpd ntpsec-1.2.2: Starting
1970-01-01T01:02:35 ntpd[1012]: INIT: Command line: /usr/sbin/ntpd -p /var/run/ntpd.pid -g -u 104:106
.
Starting NTP server: ntpd.
Starting Squeezebox client: squeezelite.
Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
996 (klogd)
.
Starting OpenBSD Secure Shell server: sshd.
Running local boot scripts (/etc/rc.local)
.
Debian GNU/Linux 12 pogoplug-dev ttyS0
pogoplug-dev login:
|
Re: Upgrading Debian Distribution May 13, 2023 03:54PM |
Admin Registered: 13 years ago Posts: 18,545 |
droidbox,
OK. Nothing was obviously wrong.
Let's correct your rootfs first, in case it was related.
Mount your USB rootfs on another Linux box. Assuming it is mounted at /media/sdb1.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
OK. Nothing was obviously wrong.
Let's correct your rootfs first, in case it was related.
Mount your USB rootfs on another Linux box. Assuming it is mounted at /media/sdb1.
cd /media/sdb1/boot ls -lartYou will see that the kernel file uImage is not the original. It has the DTB embbeded in it. You are booting with the new u-boot, so the DTB is loaded seprately. To correct this
cp -a uImage uImage.pogo_e02 cp -a uImage.orig uImage syncAnd unmount the USB drive. Take it to the Pogo E02 and boot again. Let's see it will behave differently. And post serial console log again.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Upgrading Debian Distribution May 13, 2023 04:07PM |
Registered: 9 years ago Posts: 54 |
Hmmm.
trd
load_initrd_addr=0x1100000
load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage
load_uimage_addr=0x800000
machid=0x831
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
partition=nand0,2
preboot_nc=run if_netconsole start_netconsole
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done
serverip=192.168.0.220
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=3 $mtdparts $custom_params
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
uenv_addr=0x810000
uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize
uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done;
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi
usb_ready_retry=15
Environment size: 2844/131068 bytes
PogoE02> boot
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices...
Use USB retry period from the environment: 15 second(s)
1 Storage Device(s) found
Unknown command 'ide' - try 'help'
Unknown command 'mmc' - try 'help'
Partition Map for USB device 0 -- Partition Type: DOS
Part Start Sector Num Sectors UUID Type
1 2048 14680064 068ddb4f-01 83
2 14682112 951296 068ddb4f-02 82
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
## Unknown partition table type 0
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **
Unknown command 'ide' - try 'help'
Unknown command 'mmc' - try 'help'
running scan_disk ...
Scan device usb
device usb 0:1
1 bytes read in 722 ms (0 Bytes/s)
Found bootable drive on usb 0
loading uImage ...
5435888 bytes read in 1070 ms (4.8 MiB/s)
loading uInitrd ...
9671091 bytes read in 1089 ms (8.5 MiB/s)
loading DTB /boot/dts/kirkwood-pogo_e02.dtb ...
10114 bytes read in 3783 ms (2 KiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-5.13.6-kirkwood-tld-1
Created: 2021-09-24 0:22:58 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5435824 Bytes = 5.2 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-5.13.6-kirkwood-tld-1
Created: 2021-09-24 1:06:32 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9671027 Bytes = 9.2 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
Booting using the fdt blob at 0x1c00000
Loading Kernel Image ... OK
Loading Ramdisk to 0f1d6000, end 0fb0f173 ... OK
Loading Device Tree to 0f1d0000, end 0f1d5781 ... OK
Using machid 0x831 from environment
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 5.13.6-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 PREEMPT Sat Jul 31 22:10:39 PDT 2021
[ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: CloudEngines Pogoplug E02
[ 0.000000][ T0] Memory policy: Data cache writeback
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 65024
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=3 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
[ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 231060K/262144K available (11264K kernel code, 1553K rwdata, 4272K rodata, 1024K init, 309K bss, 31084K reserved, 0K cma-reserved)
[ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x408/0x7b4 with crng_init=0
[ 0.000000][ T0] trace event string verifier disabled
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000002][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.000061][ T0] Switching to timer-based delay loop, resolution 5ns
[ 0.000937][ T0] Console: colour dummy device 80x30
[ 0.001013][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000)
[ 0.001058][ T0] pid_max: default: 32768 minimum: 301
[ 0.001471][ T0] LSM: Security Framework initializing
[ 0.001655][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.001703][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.003164][ T0] CPU: Testing write buffer coherency: ok
[ 0.005605][ T1] Setting up static identity map for 0x100000 - 0x100058
[ 0.005915][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2
[ 0.006278][ T1] rcu: Hierarchical SRCU implementation.
[ 0.007721][ T1] devtmpfs: initialized
[ 0.013431][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.013487][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.050997][ T1] prandom32: self test passed (less than 6 bits correlated)
[ 0.051042][ T1] prandom: seed boundary self test passed
[ 0.055250][ T1] prandom: 100 self tests passed
[ 0.055270][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.056921][ T1] NET: Registered protocol family 16
[ 0.057777][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.058777][ T1] audit: initializing netlink subsys (disabled)
[ 0.060304][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.060683][ T16] audit: type=2000 audit(0.050:1): state=initialized audit_enabled=0 res=1
[ 0.060841][ T1] cpuidle: using governor ladder
[ 0.060941][ T1] cpuidle: using governor menu
[ 0.061457][ T1] Feroceon L2: Enabling L2
[ 0.061511][ T1] Feroceon L2: Cache support initialised.
[ 0.069918][ T1] No ATAGs?
[ 2.560068][ C0] random: fast init done
[ 4.957176][ T39] "cryptomgr_test" (39) uses obsolete ecb(arc4) skcipher
[ 4.983759][ T59] wait_for_initramfs() called before rootfs_initcalls
[ 5.170302][ T1] raid6: int32x8 gen() 108 MB/s
[ 5.340242][ T1] raid6: int32x8 xor() 68 MB/s
[ 5.510188][ T1] raid6: int32x4 gen() 109 MB/s
[ 5.680077][ T1] raid6: int32x4 xor() 71 MB/s
[ 5.850228][ T1] raid6: int32x2 gen() 142 MB/s
[ 6.020096][ T1] raid6: int32x2 xor() 85 MB/s
[ 6.190198][ T1] raid6: int32x1 gen() 97 MB/s
[ 6.360100][ T1] raid6: int32x1 xor() 59 MB/s
[ 6.360118][ T1] raid6: using algorithm int32x2 gen() 142 MB/s
[ 6.360132][ T1] raid6: .... xor() 85 MB/s, rmw enabled
[ 6.360144][ T1] raid6: using intx1 recovery algorithm
[ 6.360443][ T1] vgaarb: loaded
[ 6.361035][ T1] SCSI subsystem initialized
[ 6.361596][ T1] usbcore: registered new interface driver usbfs
[ 6.361672][ T1] usbcore: registered new interface driver hub
[ 6.361733][ T1] usbcore: registered new device driver usb
[ 6.361950][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 6.361967][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 6.362003][ T1] PTP clock support registered
[ 6.363928][ T1] clocksource: Switched to clocksource orion_clocksource
[ 6.464644][ T1] VFS: Disk quotas dquot_6.6.0
[ 6.464757][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 6.483879][ T1] NET: Registered protocol family 2
[ 6.484121][ T1] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 6.494035][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 6.494094][ T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 6.494146][ T1] TCP bind hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 6.494186][ T1] TCP: Hash tables configured (established 2048 bind 2048)
[ 6.494450][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 6.494535][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 6.494577][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 6.494845][ T1] NET: Registered protocol family 1
[ 6.495627][ T1] RPC: Registered named UNIX socket transport module.
[ 6.495652][ T1] RPC: Registered udp transport module.
[ 6.495665][ T1] RPC: Registered tcp transport module.
[ 6.495677][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 6.495695][ T1] PCI: CLS 0 bytes, default 32
[ 6.495876][ T1] NetWinder Floating Point Emulator V0.97 (double precision)
[ 6.496502][ T58] Trying to unpack rootfs image as initramfs...
[ 8.238110][ T58] Freeing initrd memory: 9448K
[ 8.860969][ T1] Initialise system trusted keyrings
[ 8.861044][ T1] Key type blacklist registered
[ 8.861316][ T1] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[ 8.861447][ T1] zbud: loaded
[ 8.862987][ T1] NFS: Registering the id_resolver key type
[ 8.863032][ T1] Key type id_resolver registered
[ 8.863047][ T1] Key type id_legacy registered
[ 8.863094][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 8.863121][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 8.863137][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 8.863420][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 8.864077][ T1] fuse: init (API version 7.34)
[ 8.864502][ T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 8.864733][ T1] orangefs_init: module version upstream loaded
[ 8.864753][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled
[ 8.967888][ T1] xor: measuring software checksum speed
[ 8.976869][ T1] arm4regs : 1113 MB/sec
[ 8.991683][ T1] 8regs : 667 MB/sec
[ 9.001878][ T1] 32regs : 971 MB/sec
[ 9.001898][ T1] xor: using function: arm4regs (1113 MB/sec)
[ 9.001922][ T1] async_tx: api initialized (async)
[ 9.001943][ T1] Key type asymmetric registered
[ 9.001957][ T1] Asymmetric key parser 'x509' registered
[ 9.002023][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[ 9.002106][ T1] io scheduler bfq registered
[ 9.201842][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 9.204179][ T1] mv_xor f1060800.xor: Marvell shared XOR driver
[ 9.265073][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 9.267736][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 9.325056][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[ 9.327973][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 9.329388][ T1] printk: console [ttyS0] disabled
[ 9.329492][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A
[ 10.180218][ T1] printk: console [ttyS0] enabled
[ 10.194298][ T1] loop: module loaded
[ 10.199471][ T1] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it
[ 10.208928][ T1] ONFI parameter recovery failed, aborting
[ 10.214645][ T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[ 10.221731][ T1] nand: Hynix NAND 128MiB 3,3V 8-bit
[ 10.226913][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 10.235545][ T1] Scanning device for bad blocks
[ 10.263019][ T1] Bad eraseblock 193 at 0x000001820000
[ 10.342253][ T1] Bad eraseblock 825 at 0x000006720000
[ 10.370808][ T1] 4 cmdlinepart partitions found on MTD device orion_nand
[ 10.377830][ T1] Creating 4 MTD partitions on "orion_nand":
[ 10.383700][ T1] 0x000000000000-0x000000100000 : "u-boot"
[ 10.390976][ T1] 0x000000100000-0x000000500000 : "uImage"
[ 10.398203][ T1] 0x000000500000-0x000002500000 : "rootfs"
[ 10.405533][ T1] 0x000002500000-0x000008000000 : "data"
[ 10.413436][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 10.422060][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 10.433634][ T1] libphy: Fixed MDIO Bus: probed
[ 10.440052][ T1] libphy: orion_mdio_bus: probed
[ 10.461776][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 11.225004][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 52:3b:20:9c:11:51
[ 11.234654][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 11.241950][ T1] ehci-pci: EHCI PCI platform driver
[ 11.247202][ T1] ehci-orion: EHCI orion driver
[ 11.252148][ T1] orion-ehci f1050000.ehci: EHCI Host Controller
[ 11.258428][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 11.267031][ T1] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[ 11.293975][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 11.301042][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13
[ 11.310089][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 11.318074][ T1] usb usb1: Product: EHCI Host Controller
[ 11.323678][ T1] usb usb1: Manufacturer: Linux 5.13.6-kirkwood-tld-1 ehci_hcd
[ 11.331136][ T1] usb usb1: SerialNumber: f1050000.ehci
[ 11.337325][ T1] hub 1-0:1.0: USB hub found
[ 11.341854][ T1] hub 1-0:1.0: 1 port detected
[ 11.347393][ T1] usbcore: registered new interface driver usb-storage
[ 11.354616][ T1] mousedev: PS/2 mouse device common for all mice
[ 11.633982][ T17] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 11.835666][ T17] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=77.64
[ 11.844624][ T17] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 11.852528][ T17] usb 1-1: Product: USB2.0 Hub
[ 11.858144][ T17] hub 1-1:1.0: USB hub found
[ 11.862921][ T17] hub 1-1:1.0: 4 ports detected
[ 12.183957][ T17] usb 1-1.4: new high-speed USB device number 3 using orion-ehci
[ 12.334916][ T17] usb 1-1.4: New USB device found, idVendor=0781, idProduct=5571, bcdDevice= 1.26
[ 12.344054][ T17] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 12.352127][ T17] usb 1-1.4: Product: Firebird USB Flash Drive
[ 12.358197][ T17] usb 1-1.4: Manufacturer: SanDisk
[ 12.363205][ T17] usb 1-1.4: SerialNumber: 4C532000031011101542
[ 12.370249][ T17] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[ 12.377892][ T17] scsi host0: usb-storage 1-1.4:1.0
[ 12.403966][ T1] rtc-mv f1010300.rtc: internal RTC not ticking
[ 12.410280][ T1] i2c /dev entries driver
[ 12.415188][ T1] device-mapper: uevent: version 1.0.3
[ 12.420843][ T1] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com
[ 12.430512][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 12.437852][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 12.445234][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 12.452652][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 12.459502][ T1] device-mapper: raid: Loading target version 1.15.1
[ 12.467581][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 12.473808][ T1] drop_monitor: Initializing network drop monitor service
[ 12.481361][ T1] NET: Registered protocol family 10
[ 12.487952][ T1] Segment Routing with IPv6
[ 12.492341][ T1] RPL Segment Routing with IPv6
[ 12.497264][ T1] NET: Registered protocol family 17
[ 12.502719][ T1] Key type dns_resolver registered
[ 12.508311][ T1] registered taskstats version 1
[ 12.513144][ T1] Loading compiled-in X.509 certificates
[ 12.519148][ T1] zswap: loaded using pool lzo/zbud
[ 12.524654][ T1] Key type ._fscrypt registered
[ 12.529393][ T1] Key type .fscrypt registered
[ 12.534112][ T1] Key type fscrypt-provisioning registered
[ 12.542041][ T1] Key type big_key registered
[ 12.577865][ T1] Key type encrypted registered
[ 12.589233][ T1] Freeing unused kernel memory: 1024K
[ 12.614759][ T1] Checked W+X mappings: passed, no W+X pages found
[ 12.621166][ T1] Run /init as init process
Loading, please wait...
Starting version 247.3-6
[ 13.445160][ T7] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Fit 1.26 PQ: 0 ANSI: 5
[ 13.468011][ T58] sd 0:0:0:0: [sda] 15633408 512-byte logical blocks: (8.00 GB/7.45 GiB)
[ 13.490427][ T58] sd 0:0:0:0: [sda] Write Protect is off
[ 13.504857][ T58] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 13.531225][ T58] sda: sda1 sda2
[ 13.541232][ T58] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 13.683778][ T141] usbcore: registered new interface driver uas
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.36.1
[/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1
rootfs: clean, 32545/458752 files, 336844/1835008 blocks
done.
[ 17.615379][ T162] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 17.678960][ T162] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 3.06 booting
Using makefile-style concurrent boot in runlevel S.
Setting hostname to 'pogoplug-dev'...done.
Starting hotplug events dispatcher: systemd-udevd.
Synthesizing the initial hotplug events (subsystems)...done.
Synthesizing the initial hotplug events (devices)...done.
Waiting for /dev to be fully populated...[ 21.124334][ T343] orion_wdt: Initial timeout 21 sec
[ 21.765126][ T342] marvell-cesa f1030000.crypto: CESA device successfully registered
[ 21.920277][ T355] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 22.137777][ C0] random: crng init done
---- > PAUSE < ----
Timed out for waiting the udev queue being empty.
done (timeout).
Activating swap:.
[ 142.423655][ T504] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro. Quota mode: none.
Will now check all file systems.
Checking all file systems.
LABEL=rootfs is mounted
Done checking file systems.
Log is being saved in /var/log/fsck/checkfs if that location is writable.
Cleaning up temporary files...Cleaning /tmp...done.
/tmp.
Will now mount local filesystems:.
Will now activate swapfile swap, if any:done.
Checking minimum space in /tmp...done.
Cleaning up temporary files....
Starting Setting kernel variables: sysctl.
Initializing random number generator...done.
Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.3-P1
Copyright 2004-2022 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/52:3b:20:9c:11:51
Sending on LPF/eth0/52:3b:20:9c:11:51
Sending on Socket/fallback
DHCPREQUEST for 10.10.172.181 on eth0 to 255.255.255.255 port 67
[ 148.279864][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 148.290536][ T17] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
DHCPREQUEST for 10.10.172.181 on eth0 to 255.255.255.255 port 67
DHCPACK of 10.10.172.181 from 10.10.172.1
bound to 10.10.172.181 -- renewal in 32445 seconds.
done.
Starting RPC port mapper daemon: rpcbind.
Starting NFS common utilities: statd idmapd.
Cleaning up temporary files....
INIT: Entering runlevel: 2
Using makefile-style concurrent boot in runlevel 2.
Not starting NFS kernel daemon: no exports ... (warning).
Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1014 (syslogd)
.
Starting system message bus: dbus.
Starting LCDd: LCDd.
Starting NTP server: ntpd1970-01-01T01:02:34 ntpd[1059]: INIT: ntpd ntpsec-1.2.2: Starting
1970-01-01T01:02:34 ntpd[1059]: INIT: Command line: /usr/sbin/ntpd -p /var/run/ntpd.pid -g -u 104:106
.
Starting NTP server: ntpd.
Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1038 (klogd)
.
Starting Squeezebox client: squeezelite.
Starting OpenBSD Secure Shell server: sshd.
Running local boot scripts (/etc/rc.local)
.
Debian GNU/Linux 12 pogoplug-dev ttyS0
pogoplug-dev login:
|
Re: Upgrading Debian Distribution May 13, 2023 05:26PM |
Admin Registered: 13 years ago Posts: 18,545 |
Ok. I just noticed that your udev is a much older version.
It should be 252.6-1
Also list the Debian version, It should show Debian 12.0.
To make sure you are fully in bookworm, rerun
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 2 time(s). Last edit at 05/13/2023 05:28PM by bodhi.
Quote
Starting version 247.3-6
It should be 252.6-1
dpkg -l | grep udev
Also list the Debian version, It should show Debian 12.0.
cat /etc/debian_version
To make sure you are fully in bookworm, rerun
apt-get update apt-get dist-upgrade
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 2 time(s). Last edit at 05/13/2023 05:28PM by bodhi.
|
Re: Upgrading Debian Distribution May 13, 2023 05:58PM |
Registered: 9 years ago Posts: 54 |
It looks fine :-(
root@pogoplug-dev:~# dpkg -l | grep udev ii libudev0:armel 200-1 armel compatibility wrapper for libudev version 0 ii libudev1:armel 252.6-1 armel libudev shared library ii udev 252.6-1 armel /dev/ and hotplug management daemon
root@pogoplug-dev:~# cat /etc/debian_version 12.0
root@pogoplug-dev:~# apt-get update Get:1 http://ftp.de.debian.org/debian bookworm InRelease [185 kB] Get:2 http://cdn-fastly.deb.debian.org/debian bookworm-updates InRelease [49.6 kB] Get:3 https://security.debian.org/debian-security bookworm-security InRelease [48.0 kB] Fetched 283 kB in 5s (60.4 kB/s) Reading package lists... Done root@pogoplug-dev:~# apt-get dist-upgrade Reading package lists... Done Building dependency tree... Done Reading state information... Done Calculating upgrade... Done 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded.
|
Re: Upgrading Debian Distribution May 13, 2023 07:25PM |
Admin Registered: 13 years ago Posts: 18,545 |
Ah OK.
I think I know the reason why the running udev is the older version. Let me write some additional instruction in the 1st post and let you know when to do it.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 2 time(s). Last edit at 05/13/2023 07:27PM by bodhi.
I think I know the reason why the running udev is the older version. Let me write some additional instruction in the 1st post and let you know when to do it.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 2 time(s). Last edit at 05/13/2023 07:27PM by bodhi.
|
Re: Upgrading Debian Distribution May 14, 2023 03:18PM |
Admin Registered: 13 years ago Posts: 18,545 |
Added to the 1st post.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Quote
5. In Debian bookworm, the switch over to /usr is in effect. The following old sytsem folders are now symlinks to the real location in /usr.
# ls -l /{bin,lib,sbin}
lrwxrwxrwx 1 root root 7 Apr 26 14:04 /bin -> usr/bin
lrwxrwxrwx 1 root root 7 Apr 26 14:04 /lib -> usr/lib
lrwxrwxrwx 1 root root 8 Apr 26 14:04 /sbin -> usr/sbin
So if for whatever reason, your file system does not show these 3 folders as symlinks, then you'll need to adjust them.
And also make sure that your rootfs backup conform to this structure, too.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
