|
Debian on WD My Cloud August 09, 2017 01:14PM |
Registered: 10 years ago Posts: 82 |
BootROM - 1.51
Booting from SPI flash
General initialization - Version: 1.0.0
High speed PHY - Version: 0.1.1 (COM-PHY-V20)
USB2 UTMI PHY initialized succesfully
USB2 UTMI PHY initialized succesfully
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run with PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
** LOADER **
U-Boot 2013.01_v1.03 (Nov 20 2014 - 16:39:45) Marvell version: 2014_T2.0p3
Board: WD_Glacier_DB-88F6720-V2
SoC: MV88F6720 Rev A0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 800 [MHz]
L2 @ 400 [MHz]
TClock @ 200 [MHz]
DDR @ 534 [MHz]
DDR 16Bit Width, FastPath Memory Access, DLB Enabled
DRAM: 512 MiB
Map: Code: 0x1fed6000:0x1ff92c90
BSS: 0x1ffefa20
Stack: 0x1f9c5f20
Heap: 0x1f9c6000:0x1fed6000
SF: Detected MX25L8006E with page size 64 KiB, total 1 MiB
*** Warning - bad CRC, using default environment
PCI-e 0: Detected No Link.
PCI-e 1: Detected No Link.
SF: Detected MX25L8006E with page size 64 KiB, total 1 MiB
MAC addr: 00:14:EE:0B:96:E9
### Loading Firmware from USB 3.0 Disk ###
USB2.0 0: Host Mode
USB2.0 1: Device Mode
USB3.0 0: Host Mode
Board configuration detected:
GE-PHY-0 on MAC0
SERDES configuration:
Lane #0: PCIe0
Lane #1: PCIe1
Lane #2: SATA0
Lane #3: USB3
Net: egiga0 [PRIME]
*** ERROR: ping address not given
Hit any key to stop autoboot: 0
(Re)start USB...
USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
## Booting image at 00a00000 ...
### Loading Firmware from USB 2.0 Disk ###
(Re)start USB...
USB0: Port (usbActive) : 1 Interface (usbType = 2) : USB EHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
## Booting image at 00a00000 ...
### Loading Firmware from Disk ###
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
** Bad device ide 0 **
** Bad device ide 0 **
## Booting image at 00a00000 ...
### Loading Rescure Firmware from Disk ###
** Bad device ide 0 **
** Bad device ide 0 **
## Booting image at 00a00000 ...
### Start network installation ###
RX_ICMP
rx_icmp(): Listening to incoming WD ICMP beacons for 3 second!
Error...
rxIcmp - rxIcmp
Usage:
rxIcmp Start Listening to incoming WD ICMP beacons
## Booting image at 00a00000 ...
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Marvell>> help
? - alias for 'help'
Creset - Creset - Run 'reset' or boot command in a loop, while counting.
SatR - Sample At Reset sub-system
active_units- print active units on board
base - print or set address offset
bdinfo - print Board Info structure
boot - boot default, i.e., run 'bootcmd'
boot_menu- command allows to select boot script from boot device
example: boot_menu
bootd - boot default, i.e., run 'bootcmd'
bootelf - Boot from an ELF image in memory
bootm - boot application image from memory
bootp - boot image via network using BOOTP/TFTP protocol
bootvx - Boot vxWorks from an ELF image
bootz - boot Linux zImage image from memory
bubt - bubt - Burn an image on the Boot SPI Flash.
chpart - change active partition
cmp - memory compare
coninfo - print console devices and information
cp - memory copy
crc32 - checksum calculation
date - get/set/reset date & time
ddrPhyRead- ddrPhyRead - Read DDR PHY register
ddrPhyWrite- ddrPhyWrite - Write DDR PHY register
dhcp - boot image via network using DHCP/TFTP protocol
diskboot- diskboot- boot from IDE device
dma - dma - Perform DMA using the XOR engine
echo - echo args to console
editenv - edit environment variable
eeprom - EEPROM sub-system
env - environment handling commands
exit - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls - list files in a directory (default /)
ext4load- load binary file from a Ext4 filesystem
ext4ls - list files in a directory (default /)
ext4write- create a file in the root directory
false - do nothing, unsuccessfully
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
fdt - flattened device tree utility commands
fsinfo - print information about filesystems
fsload - load binary file from a filesystem image
go - start application at address 'addr'
help - print command description/usage
i2c - I2C sub-system
ide - ide - IDE sub-system
iminfo - print header information for application image
imxtract- extract a part of a multi-image
ir - ir - reading and changing MV internal register values.
itest - return true/false on integer compare
loadb - load binary file over serial line (kermit mode)
loads - load S-Record file over serial line
loadx - load binary file over serial line (xmodem mode)
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
ls - list files in a directory (default /)
map - map - Display address decode windows
md - memory display
me - me - PCIe master enable
mm - memory modify (auto-incrementing address)
mp - mp - map PCIe BAR
mtdparts- define flash/nand partitions
mtest - simple RAM read/write test
mw - memory write (fill)
nfs - boot image via network using NFS protocol
nm - memory modify (constant address)
pci - list and access PCI Configuration Space
pciePhyRead- phyRead - Read PCI-E Phy register
pciePhyWrite- pciePhyWrite - Write PCI-E Phy register
phyRead - phyRead - Read Phy register
phyWrite- phyWrite - Write Phy register
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
pxe - commands to get and boot from pxe files
rcvr - rcvr - Start recovery process (with TFTP server)
reset - Perform RESET of the CPU
resetenv- resetenv - Erase environment sector to reset all variables to default.
run - run commands in an environment variable
rxIcmp - rxIcmp
scsi - SCSI sub-system
scsiboot- boot from SCSI device
se - se - PCIe Slave enable
setenv - set environment variables
sf - SPI flash sub-system
sg - sg - scanning the PHYs status
showvar - print local hushshell variables
sleep - delay execution for some time
source - run script from memory
sp - scan and detect all devices on PCI-e interface
sspi - SPI utility command
stage_boot- command to load script/image from different devices
example: stage_boot hd_img pxe
sys_restore- sys_restore - Search for install script on USB DOK and start installation of linux kernel and rootfs.
sysboot - command to get and boot from syslinux files
temp - temp - Display the device temperature.
tempCmd0- tempCmd - This command allocated for monitor extinction
tempCmd1- tempCmd - This command allocated for monitor extinction
tempCmd2- tempCmd - This command allocated for monitor extinction
tempCmd3- tempCmd - This command allocated for monitor extinction
test - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
training- training - prints the results of the DDR3 Training.
true - do nothing, successfully
ts_report- ts_report - report touch screen coordinate
ts_test - ts_test - test touch screen
ubi - ubi commands
ubifsload- load file from an UBIFS filesystem
ubifsls - list files in a directory
ubifsmount- mount UBIFS volume
ubifsumount- unmount UBIFS volume
usb - USB sub-system
usbboot - boot from USB device
version - print monitor, compiler and linker version
whoAmI - - reading CPU ID
Marvell>> printenv
CASset=max
MALLOC_len=5
MPmode=SMP
autoload=no
baudrate=115200
boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr
bootargs=root=/dev/ram console=ttyS0,115200
bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel
bootargs_end=:10.4.50.254:255.255.255.0:Armada375:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=usb reset; fatload usb 0:1 0xa00000 /boot/uImage; fatload usb 0:1 0xf00000 /boot/uRamdisk; bootm 0xa00000 0xf00000
bootcmd_auto=stage_boot $boot_order
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot
bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000;
bootdelay=1
cacheShare=no
console=console=ttyS0,115200
device_partition=0:1
disL2Cache=yes
disL2Prefetch=yes
disaMvPnp=no
eeeEnable=no
enaClockGating=no
enaCpuStream=no
enaDCPref=yes
enaFPU=yes
enaICPref=yes
enaMonExt=no
enaWrAllo=no
eth1addr=00:50:43:00:02:02
eth1mtu=1500
eth2addr=00:50:43:00:00:02
eth2mtu=1500
eth3addr=00:50:43:02:00:00
eth3mtu=1500
ethact=egiga0
ethaddr=00:14:EE:0B:96:E9
ethmtu=1500
ethprime=egiga0
fdt_addr=2040000
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-375-db.dtb
ide_path=/
image_name=uImage
initrd_name=uInitrd
ipaddr=2.76.78.201
kernel_addr_r=2080000
lcd0_enable=0
lcd0_params=640x480-16@60
lcd_panel=0
loadaddr=0x02000000
loads_echo=0
mtdids=spi0=spi_flash
mtdparts=mtdparts=spi_flash:4m(boot),-(spi-rootfs)
mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500
mv_pon_addr=00:50:43:02:00:00
netbsd_en=no
netmask=255.0.0.0
netretry=no
pcieTune=no
pexMode=RC
pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
ramdisk_addr_r=2880000
rootpath=/srv/nfs/
sata_delay_reset=0
sata_dma_mode=yes
script_addr_r=3000000
script_name=boot.scr
serverip=192.168.1.1
setL2CacheWT=no
standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usbActive=1
usbType=2
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
Environment size: 3077/65532 bytes
Marvell>>
|
Re: Debian on WD My Cloud August 09, 2017 05:45PM |
Admin Registered: 13 years ago Posts: 18,580 |
|
Re: Debian on WD My Cloud August 10, 2017 03:00PM |
Registered: 10 years ago Posts: 82 |
Marvell>> setenv bootargs $console root=LABEL=rootfs rootdelay=5 rootfstype=ext2 earlyprintk=serial
Marvell>> usb reset; ext2load usb 0:1 0xa00000 /boot/uImage; ext2load usb 0:1 0xf00000 /boot/uInitrd; bootm 0xa00000 0xf00000
(Re)start USB...
USB0: Port (usbActive) : 1 Interface (usbType = 2) : USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
3917433 bytes read in 456 ms (8.2 MiB/s)
6210503 bytes read in 557 ms (10.6 MiB/s)
### Start network installation ###
RX_ICMP
rx_icmp(): Listening to incoming WD ICMP beacons for 3 second!
Error...
rxIcmp - rxIcmp
Usage:
rxIcmp Start Listening to incoming WD ICMP beacons
## Booting image at 00a00000 ...
## Booting kernel from Legacy Image at 00a00000 ...
Image Name: Linux-4.9.0-mvebu-tld-12
Created: 2017-08-10 19:45:04 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3917369 Bytes = 3.7 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 00f00000 ...
Image Name: initramfs-4.9.0-mvebu-tld-12
Created: 2017-02-03 23:57:32 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 6210439 Bytes = 5.9 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.0-mvebu-tld-12 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017
[ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt:Machine model: Marvell Armada 375 Development Board
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] percpu: Embedded 15 pages/cpu @dfbce000 s30796 r8192 d22452 u61440
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=5 rootfstype=ext2 earlyprintk=serial
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 500156K/524288K available (8192K kernel code, 690K rwdata, 2052K rodata, 1024K init, 386K bss, 24132K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB)
[ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB)
[ 0.000000] .data : 0xc0d00000 - 0xc0daca28 ( 691 kB)
[ 0.000000] .bss : 0xc0daca28 - 0xc0e0d4f8 ( 387 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] mvebu_mbus: [Firmware Warn]: deprecated mbus-mvebu Device Tree, suspend/resume will not work
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000] L2C-310 D prefetch enabled, offset 1 lines
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 Coherent cache controller enabled, 8 ways, 256 kB
[ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56040001
[ 0.000000] Switching to timer-based delay loop, resolution 40ns
[ 0.000007] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns
[ 0.007892] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.019251] Console: colour dummy device 80x30
[ 0.023777] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
[ 0.034208] pid_max: default: 32768 minimum: 301
[ 0.039041] Security Framework initialized
[ 0.043273] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.049960] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.057893] CPU: Testing write buffer coherency: ok
[ 0.063094] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.068876] Setting up static identity map for 0x100000 - 0x100058
[ 0.075455] mvebu-soc-id: MVEBU SoC ID=0x6720, Rev=0x3
[ 0.274629] Booting CPU 1
[ 0.277547] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.277664] Brought up 2 CPUs
[ 0.286446] SMP: Total of 2 processors activated (100.00 BogoMIPS).
[ 0.292770] CPU: All CPU(s) started in SVC mode.
[ 0.298445] devtmpfs: initialized
[ 0.305379] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.313602] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.323615] prandom: seed boundary self test passed
[ 0.331943] prandom: 100 self tests passed
[ 0.336148] pinctrl core: initialized pinctrl subsystem
[ 0.342860] NET: Registered protocol family 16
[ 0.348475] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.384835] cpuidle: using governor ladder
[ 0.414910] cpuidle: using governor menu
[ 0.419073] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.427178] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.505820] vgaarb: loaded
[ 0.508892] SCSI subsystem initialized
[ 0.513964] usbcore: registered new interface driver usbfs
[ 0.519742] usbcore: registered new interface driver hub
[ 0.525302] usbcore: registered new device driver usb
[ 0.530699] media: Linux media interface: v0.10
[ 0.535411] Linux video capture interface: v2.00
[ 0.541454] clocksource: Switched to clocksource armada_370_xp_clocksource
[ 0.597706] VFS: Disk quotas dquot_6.6.0
[ 0.601882] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.621134] NET: Registered protocol family 2
[ 0.626393] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.633574] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.640130] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.646646] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.652850] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.659371] NET: Registered protocol family 1
[ 0.664346] RPC: Registered named UNIX socket transport module.
[ 0.670329] RPC: Registered udp transport module.
[ 0.675132] RPC: Registered tcp transport module.
[ 0.679901] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.686671] Unpacking initramfs...
[ 0.690150] Initramfs unpacking failed: junk in compressed archive
[ 0.702178] Freeing initrd memory: 6068K (c0f00000 - c14ed000)
[ 0.708224] NetWinder Floating Point Emulator V0.97 (double precision)
[ 0.716225] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.722576] audit: initializing netlink subsys (disabled)
[ 0.728078] audit: type=2000 audit(0.710:1): initialized
[ 0.733875] Initialise system trusted keyrings
[ 0.738684] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 0.745375] zbud: loaded
[ 0.748963] NFS: Registering the id_resolver key type
[ 0.754149] Key type id_resolver registered
[ 0.758401] Key type id_legacy registered
[ 0.762520] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.769278] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.776005] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 0.783708] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 0.790444] orangefs_init: module version upstream loaded
[ 0.799705] Key type asymmetric registered
[ 0.803909] Asymmetric key parser 'x509' registered
[ 0.808974] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 0.816459] io scheduler noop registered
[ 0.820452] io scheduler deadline registered
[ 0.824837] io scheduler cfq registered (default)
[ 0.908705] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.922369] libphy: Fixed MDIO Bus: probed
[ 0.927884] libphy: mdio_driver_register: mv88e6085
[ 0.934124] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.940732] ehci-pci: EHCI PCI platform driver
[ 0.945458] ehci-orion: EHCI orion driver
[ 0.950229] usbcore: registered new interface driver usblp
[ 0.955977] usbcore: registered new interface driver usb-storage
[ 0.962619] mousedev: PS/2 mouse device common for all mice
[ 0.969536] i2c /dev entries driver
[ 0.975681] hidraw: raw HID events driver (C) Jiri Kosina
[ 0.981884] usbcore: registered new interface driver usbhid
[ 0.987521] usbhid: USB HID core driver
[ 0.991790] drop_monitor: Initializing network drop monitor service
[ 0.998165] Netfilter messages via NETLINK v0.30.
[ 1.003026] ip_set: protocol 6
[ 1.006494] NET: Registered protocol family 10
[ 1.022142] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 1.030074] NET: Registered protocol family 17
[ 1.034997] 8021q: 802.1Q VLAN Support v1.8
[ 1.039299] Key type dns_resolver registered
[ 1.043822] ThumbEE CPU extension supported.
[ 1.048170] Registering SWP/SWPB emulation handler
[ 1.054043] registered taskstats version 1
[ 1.058214] Loading compiled-in X.509 certificates
[ 1.063162] zswap: loaded using pool lzo/zbud
[ 1.136559] Key type big_key registered
[ 1.140954] Key type encrypted registered
[ 1.147119] hctosys: unable to open rtc device (rtc0)
[ 4.321446] Unable to handle kernel paging request at virtual address e0000000
[ 4.328727] pgd = c0004000
[ 4.331508] [e0000000] *pgd=00000000
[ 4.335171] Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[ 4.340545] Modules linked in:
[ 4.343686] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.9.0-mvebu-tld-12 #2
[ 4.350701] Hardware name: Marvell Armada 375 (Device Tree)
[ 4.356334] task: df495300 task.stack: df496000
[ 4.360935] PC is at crc32_be+0x70/0x140
[ 4.364926] LR is at 0x7
[ 4.367537] pc : [<c04d5c50>] lr : [<00000007>] psr: 80000113
[ 4.367537] sp : df497ed4 ip : e0000000 fp : 00000000
[ 4.379133] r10: f4c5a8db r9 : 0afcdeba r8 : 00001410
[ 4.384419] r7 : 00001810 r6 : 00001010 r5 : 00001c10 r4 : b1f564b0
[ 4.391002] r3 : c0933bf0 r2 : f0defde0 r1 : c11666d0 r0 : 5587a677
[ 4.397586] Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 4.404774] Control: 10c5387d Table: 0000404a DAC: 00000051
[ 4.410579] Process swapper/0 (pid: 1, stack limit = 0xdf496220)
[ 4.416643] Stack: (0xdf497ed4 to 0xdf498000)
[ 4.421066] 7ec0: f0defde7 c0e02f74 00000000
[ 4.429295] 7ee0: 00000101 c0daca40 c0c640ac c0c5183c 00000000 c0c3bda0 ffffe000 c0c3bd78
[ 4.437524] 7f00: 00000000 c01019bc df4fa380 c0903c60 c0dd3aa4 cccccccd c0daca00 c029cc94
[ 4.445752] 7f20: dfffce04 dfffce10 c0b0065c c013f774 00000003 00000001 c0aff25c 00000007
[ 4.453980] 7f40: 00000007 c0b00670 00000100 c0b00670 c0d0dbc0 00000008 c0daca40 00000008
[ 4.462207] 7f60: c0daca40 c0c51838 00000101 c0daca40 c0c640ac c0c00e04 00000007 00000007
[ 4.470434] 7f80: 00000000 c0c005b4 00000000 c0834b6c 00000000 00000000 00000000 00000000
[ 4.478661] 7fa0: 00000000 c0834b74 00000000 c010c338 00000000 00000000 00000000 00000000
[ 4.486888] 7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 4.495115] 7fe0: 00000000 00000000 00000000 00000000 00000013 00000000 ffffffff ffffffff
[ 4.503357] [<c04d5c50>] (crc32_be) from [<c0c3bda0>] (of_fdt_raw_init+0x28/0x70)
[ 4.510901] [<c0c3bda0>] (of_fdt_raw_init) from [<c01019bc>] (do_one_initcall+0xa8/0x150)
[ 4.519137] [<c01019bc>] (do_one_initcall) from [<c0c00e04>] (kernel_init_freeable+0x190/0x258)
[ 4.527889] [<c0c00e04>] (kernel_init_freeable) from [<c0834b74>] (kernel_init+0x8/0x10c)
[ 4.536122] [<c0834b74>] (kernel_init) from [<c010c338>] (ret_from_fork+0x14/0x3c)
[ 4.543747] Code: e3017810 e3018410 e154000c 0a000023 (e59c9000)
[ 4.549900] ---[ end trace 9981663f8675c6f2 ]---
[ 4.554666] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[ 4.554666]
[ 4.563942] CPU0: stopping
[ 4.566730] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G D 4.9.0-mvebu-tld-12 #2
[ 4.574955] Hardware name: Marvell Armada 375 (Device Tree)
[ 4.580603] [<c01160bc>] (unwind_backtrace) from [<c0110bb4>] (show_stack+0x10/0x14)
[ 4.588403] [<c0110bb4>] (show_stack) from [<c04ba5a4>] (dump_stack+0x70/0x8c)
[ 4.595685] [<c04ba5a4>] (dump_stack) from [<c0113f90>] (handle_IPI+0x16c/0x350)
[ 4.603138] [<c0113f90>] (handle_IPI) from [<c0101520>] (gic_handle_irq+0x78/0x94)
[ 4.610762] [<c0101520>] (gic_handle_irq) from [<c011160c>] (__irq_svc+0x6c/0xa8)
[ 4.618294] Exception stack(0xc0d01f60 to 0xc0d01fa8)
[ 4.623412] 1f60: 00000001 00000000 00000000 c011e6c0 00000000 00000000 c0d00000 c0d0412c
[ 4.631641] 1f80: 00000001 c0d01fb8 c0d04194 00000000 00000000 c0d01fb0 c010d400 c010d404
[ 4.639864] 1fa0: 60000113 ffffffff
[ 4.643428] [<c011160c>] (__irq_svc) from [<c010d404>] (arch_cpu_idle+0x2c/0x38)
[ 4.650881] [<c010d404>] (arch_cpu_idle) from [<c015ef04>] (cpu_startup_entry+0xf0/0x1d0)
[ 4.659114] [<c015ef04>] (cpu_startup_entry) from [<c0c00c08>] (start_kernel+0x324/0x390)
[ 4.667344] [<c0c00c08>] (start_kernel) from [<0000807c>] (0x807c)
[ 4.673590] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[ 4.673590]
|
Re: Debian on WD My Cloud August 10, 2017 03:53PM |
Admin Registered: 13 years ago Posts: 18,580 |
usb reset; ext2load usb 0:1 0x02000000 /boot/uImage; ext2load usb 0:1 0x2900000 /boot/uInitrd; bootm 0x02000000 0x2900000
|
Re: Debian on WD My Cloud August 11, 2017 09:04AM |
Registered: 10 years ago Posts: 82 |
|
Re: Debian on WD My Cloud August 11, 2017 05:16PM |
Admin Registered: 13 years ago Posts: 18,580 |
setenv load_dtb_addr 0x1000000 setenv load_initrd_addr 0x2900000 setenv load_image_addr 0x02000000 setenv usb_set_bootargs 'setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial"' setenv fdt_skip_update yes usb start ext2load usb 0:1 $load_image_addr /boot/zImage ext2load usb 0:1 $load_dtb_addr /boot/dts/armada-xxxxx.dtb ext2load usb 0:1 $load_initrd_addr /boot/uInitrd run usb_set_bootargs bootz $load_image_addr $load_initrd_addr $load_dtb_addr
|
Re: Debian on WD My Cloud August 12, 2017 01:53AM |
Registered: 10 years ago Posts: 82 |
Marvell>> setenv load_dtb_addr 0x1000000
Marvell>> setenv load_initrd_addr 0x2900000
Marvell>> setenv load_image_addr 0x02000000
Marvell>> setenv usb_set_bootargs 'setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial"'
Marvell>> setenv fdt_skip_update yes
Marvell>> usb start
(Re)start USB...
USB0: Port (usbActive) : 1 Interface (usbType = 2) : USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Marvell>> ext2load usb 0:1 $load_image_addr /boot/zImage
3904400 bytes read in 394 ms (9.4 MiB/s)
Marvell>> ext2load usb 0:1 $load_dtb_addr /boot/dts/armada-375-db.dtb
12969 bytes read in 492 ms (25.4 KiB/s)
Marvell>> ext2load usb 0:1 $load_initrd_addr /boot/uInitrd
6210503 bytes read in 558 ms (10.6 MiB/s)
Marvell>> run usb_set_bootargs
Marvell>> bootz $load_image_addr $load_initrd_addr $load_dtb_addr
### Loading Rescure Firmware uRamdisk from USB 2.0 Disk ###
(Re)start USB...
USB0: Port (usbActive) : 1 Interface (usbType = 2) : USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
** Unrecognized filesystem type **
** Unrecognized filesystem type **
### Loading Firmware from Disk ###
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
** Bad device ide 0 **
** Bad device ide 0 **
### Loading Rescure Firmware from Disk ###
** Bad device ide 0 **
** Bad device ide 0 **
### Image start network installation ###
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
Retry count exceeded; starting again
RX_ICMP
rx_icmp(): Listening to incoming WD ICMP beacons for 3 second!
Error...
rxIcmp - rxIcmp
Usage:
rxIcmp Start Listening to incoming WD ICMP beacons
Wrong Ramdisk Image Format
Ramdisk image is corrupt or invalid
Marvell>>
|
Re: Debian on WD My Cloud August 12, 2017 04:54AM |
Admin Registered: 13 years ago Posts: 18,580 |
Marvell>> bootz $load_image_addr $load_initrd_addr $load_dtb_addr ### Loading Rescure Firmware uRamdisk from USB 2.0 Disk ###