Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's August 13, 2017 08:57AM |
Registered: 6 years ago Posts: 23 |
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's August 13, 2017 05:04PM |
Admin Registered: 13 years ago Posts: 18,575 |
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's August 14, 2017 12:33AM |
Admin Registered: 13 years ago Posts: 18,575 |
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's August 14, 2017 02:44AM |
Registered: 6 years ago Posts: 23 |
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's August 22, 2017 02:38PM |
Registered: 6 years ago Posts: 23 |
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's August 22, 2017 05:03PM |
Admin Registered: 13 years ago Posts: 18,575 |
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's August 25, 2017 02:19AM |
Admin Registered: 13 years ago Posts: 18,575 |
setenv sata_init 'mw.l f1018100 20420000; mw.l f1018140 003ca800; sleep 3; scsi init' setenv usb_init 'mw.l f1018100 20420000; mw.l f1018140 003E8800; sleep 3; usb start' setenv dtb_file '/boot/dts/armada-380-zyxel-nas326.dtb' setenv disks '0 1 2 3' setenv devices 'usb scsi' setenv load_dtb 'echo loading DTB $dtb_file ...; ext2load $bootdev $device $load_dtb_addr $dtb_file' setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/zImage' setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial' setenv scan_disk 'echo running scan_disk ...; scan_done=0; setenv scan_usb "run usb_init"; setenv scan_scsi "run sata_init"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if ext2load $dev $disknum:1 $load_image_addr /boot/zImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done' setenv bootcmd_exec 'run scan_disk; echo Booting from $bootdev $device ...; setenv fdt_skip_update yes; if run load_image; then if run load_dtb; then if run load_initrd; then run set_bootargs; bootz $load_image_addr $load_initrd_addr $load_dtb_addr; fi; fi; fi' setenv bootcmd_custom 'if run bootcmd_exec; then; else if run bootcmd_stock_1; then; else run bootcmd_stock_2; reset; fi; fi'
printenv boot
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's August 30, 2017 03:07PM |
Registered: 6 years ago Posts: 23 |
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's September 03, 2017 03:39PM |
Registered: 6 years ago Posts: 23 |
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's September 03, 2017 07:43PM |
Admin Registered: 13 years ago Posts: 18,575 |
./kwboot -t -B 115200 /dev/ttyUSB3 -d
Sending debug message. Please reboot the target...| [Type Ctrl-\ + c to quit] M - 1.73 Booting from NAND flash General initialization - Version: 1.0.0 Detected Device ID 6810 High speed PHY - Version: 2.0 Init RD NAS topology board SerDes lanes topology details: | Lane # | Speed | Type | -------------------------------- | 0 | 06 | SATA0 | | 1 | 05 | USB3 HOST0 | | 2 | 06 | SATA1 | | 5 | 05 | USB3 HOST1 | -------------------------------- High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.26.0 mvSysEnvGetTopologyUpdateInfo: TWSI Read failed DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully Not detected suspend to RAM indication BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01-svn48797 (Jan 18 2016 - 03:10:12) Marvell version: 2014_T3.0p6 Board: RD-NAS-88F6820-DDR3 SoC: MV88F6810 Rev A0 running 1 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 200 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB Map: Code: 0x1fed0000:0x1ff95e28 BSS: 0x1ffef2b4 Stack: 0x1f9cff20 Heap: 0x1f9d0000:0x1fed0000 U-Boot Environment: 0x00200000:0x00280000 (NAND) NAND: 256 MiB MMC: mv_sdh: 0 *** Booting kernel from kernel 1 @0x00000000; run bootcmd_custom; *** USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | 0x01 | egiga0 [PRIME] Hit any key to stop autoboot: 0
setenv sata_init 'mw.l f1018100 20420000; mw.l f1018140 003ca800; sleep 3; scsi init' setenv usb_init 'mw.l f1018100 20420000; mw.l f1018140 003E8800; sleep 3; usb start' setenv dtb_file '/boot/dts/armada-380-zyxel-nas326.dtb' setenv disks '0 1 2 3' setenv devices 'usb scsi' setenv load_dtb 'echo loading DTB $dtb_file ...; ext2load $bootdev $device $load_dtb_addr $dtb_file' setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/zImage' setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial' setenv scan_disk 'echo running scan_disk ...; scan_done=0; setenv scan_usb "run usb_init"; setenv scan_scsi "run sata_init"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if ext2load $dev $disknum:1 $load_image_addr /boot/zImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done' setenv bootcmd_exec 'run scan_disk; echo Booting from $bootdev $device ...; setenv fdt_skip_update yes; if run load_image; then if run load_dtb; then if run load_initrd; then run set_bootargs; bootz $load_image_addr $load_initrd_addr $load_dtb_addr; fi; fi; fi' setenv bootcmd_custom 'if run bootcmd_exec; then; else if run bootcmd_stock_1; then; else run bootcmd_stock_2; reset; fi; fi'
printenv boot
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's September 04, 2017 12:42PM |
Registered: 6 years ago Posts: 23 |
./kwboot -t -B 115200 /dev/ttyUSB3 -d
sage: kwboot -b <image> [ -p ] [ -t ] [-B <baud> ] <TTY> -b <image>: boot <image> -p: patch <image> to type 0x69 (uart boot) -t: mini terminal -B <baud>: set baud rate
Marvell>> Marvell>> printenv CASset=max CONTRY_TYPE=FF FEATURE_BIT=00 MALLOC_len=5 MODEL_ID=B303 MPmode=SMP PRODUCT_NAME=STG-328 VENDOR_NAME=MitraStar Technology Corp. autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=armada-nand:2m(u-boot),2m(env),2m(config),15m(kernel1),110m(rootfs1),15m(kernel2),-(rootfs2) earlyprintk=serial bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=nand read 0x2000000 0x08700000 0xF00000 && bootz 0x2000000 bootcmd_auto=stage_boot $boot_order bootcmd_custom=if run bootcmd_exec; then; else if run bootcmd_stock_1; then; else run bootcmd_stock_2; reset; fi; fi bootcmd_custom_sata=if run sata_bootcmd; then; else if run bootcmd_stock_1; then; else run bootcmd_stock_2; reset; fi; fi bootcmd_exec=run scan_disk; echo Booting from $bootdev $device ...; setenv fdt_skip_update yes; if run load_image; then if run load_dtb; then if run load_initrd; then run set_bootargs; bootz $load_image_addr $load_initrd_addr $load_dtb_addr; fi; fi; fi bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootcmd_stock_1=run set_bootargs_stock; echo Booting from NAND kernel 1 ...; nand read 0x2000000 0x00E00000 0xF00000 && bootz 0x2000000 bootcmd_stock_2=run set_bootargs_stock; echo Booting from NAND kernel 2 ...; nand read 0x2000000 0x08700000 0xF00000 && bootz 0x2000000 bootdelay=3 cacheShare=no change_boot_part=0 console=console=ttyS0,115200 core_checksum_1=e9b3248e8c69ec9ef52a8698d0835aae core_checksum_2=2773b03df8b32c243f8b84dcefa79efb curr_bootfrom=2 device_partition=0:1 devices=usb scsi disaMvPnp=no disks=0 1 2 3 dtb_file=/boot/dts/armada-380-zyxel-nas326.dtb eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:38:32:25 eth1mtu=1500 eth2addr=00:50:43:38:a6:25 eth2mtu=1500 eth3addr=00:50:43:32:a6:38 eth3mtu=1500 ethact=egiga0 ethaddr=58:8B:F3:DB:DD:3E ethmtu=1500 ethprime=egiga0 fdt_addr=2040000 fdt_skip_update=yes fdtaddr=0x1000000 fdtfile=armada-38x-modular.dtb filesize=0x6e8f80 fwversion_1=V5.21(AAZF.0) fwversion_2=V5.21(AAZF.1) ide_path=/ image_name=uImage img_checksum_1=db4be927b09d7ea9a1284d2e6f330db5 img_checksum_2=5356a1c083dfd6bc8c74bfd231aa15a6 initrd_name=uInitrd ipaddr=10.4.50.170 kernel_addr=${kernel_addr_1} kernel_addr_1=0x00000000; run bootcmd_custom; kernel_addr_2=0x08700000 kernel_addr_r=2080000 kernel_mtd_1=3 kernel_mtd_2=5 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 load_dtb=echo loading DTB $dtb_file ...; ext2load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1000000 load_image=echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/zImage load_image_addr=0x02000000 load_initrd=echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x2900000 loadaddr=0x02000000 loads_echo=0 modelid_1=B303 modelid_2=B303 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:2m(u-boot),2m(env),2m(config),15m(kernel1),110m(rootfs1),15m(kernel2),-(rootfs2) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:25:a6:38 nandEcc=nfcConfig=4bitecc netbsd_en=no netmask=255.255.255.0 netretry=no next_bootfrom=2 pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 revision_1=50967 revision_2=50984 romfile_checksum_1=4EE9 romfile_checksum_2=A762 rootpath=/srv/nfs/ sata_bootcmd=echo Booting from SATA ...; setenv fdt_skip_update yes; run sata_init; ext2load scsi 0:1 $load_image_addr /boot/zImage; ext2load scsi 0:1 $load_dtb_addr /boot/dts/armada-380-zyxel-nas326.dtb; ext2load scsi 0:1 $load_initrd_addr /boot/uInitrd; run sata_set_bootargs; bootz $load_image_addr $load_initrd_addr $load_dtb_addr sata_delay_reset=0 sata_dma_mode=yes sata_init=mw.l f1018100 20420000; mw.l f1018140 003ca800; sleep 3; scsi init sata_set_bootargs=setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial" scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "run usb_init"; setenv scan_scsi "run sata_init"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if ext2load $dev $disknum:1 $load_image_addr /boot/zImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done script_addr_r=3000000 script_name=boot.scr scsidevs=0 serial_number=S150Y46042395 serverip=10.4.50.38 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial set_bootargs_stock=setenv bootargs "console=ttyS0,115200 ubi.mtd=4,2048 rootfstype=ubifs root=ubi0:rootfs1 rw rootdelay=2" standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial sysimg_mtd_1=4 sysimg_mtd_2=6 usb0Mode=host usbActive=0 usbType=2 usb_bootcmd=echo Booting from USB ...; setenv fdt_skip_update yes; run usb_init; ext2load usb 0:1 $load_image_addr /boot/zImage; ext2load usb 0:1 $load_dtb_addr /boot/dts/armada-380-zyxel-nas326.dtb; ext2load usb 0:1 $load_initrd_addr /boot/uInitrd; run usb_set_bootargs; bootz $load_image_addr $load_initrd_addr $load_dtb_addr usb_init=mw.l f1018100 20420000; mw.l f1018140 003E8800; sleep 3; usb start usb_set_bootargs=setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial" vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 zld_checksum_1=b44f1fe16e53092068270b337dee223c zld_checksum_2=102d2dc16f397df0dddc4f1ad6380e52 Environment size: 7079/524284 bytes Marvell>> ls Scanning JFFS2 FS: done. Marvell>> setenv sata_init 'mw.l f1018100 20420000; mw.l f1018140 003ca800; sleep 3; scsi init' Marvell>> setenv usb_init 'mw.l f1018100 20420000; mw.l f1018140 003E8800; sleep 3; usb start' Marvell>> setenv dtb_file '/boot/dts/armada-380-zyxel-nas326.dtb' Marvell>> setenv disks '0 1 2 3' Marvell>> setenv devices 'usb scsi' Marvell>> setenv load_dtb 'echo loading DTB $dtb_file ...; ext2load $bootdev $device $load_dtb_addr $dtb_file' Marvell>> setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' Marvell>> setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/zImage' Marvell>> setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial' Marvell>> setenv scan_disk 'echo running scan_disk ...; scan_done=0; setenv scan_usb "run usb_init"; setenv scan_scsi "run sata_init"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if ext2load $dev $disknum:1 $load_image_addr /boot/zImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done' Marvell>> setenv bootcmd_exec 'run scan_disk; echo Booting from $bootdev $device ...; setenv fdt_skip_update yes; if run load_image; then if run load_dtb; then if run load_initrd; then run set_bootargs; bootz $load_image_addr $load_initrd_addr $load_dtb_addr; fi; fi; fi' Marvell>> setenv bootcmd_custom 'if run bootcmd_exec; then; else if run bootcmd_stock_1; then; else run bootcmd_stock_2; reset; fi; fi' Marvell>> printenv CASset=max CONTRY_TYPE=FF FEATURE_BIT=00 MALLOC_len=5 MODEL_ID=B303 MPmode=SMP PRODUCT_NAME=STG-328 VENDOR_NAME=MitraStar Technology Corp. autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=armada-nand:2m(u-boot),2m(env),2m(config),15m(kernel1),110m(rootfs1),15m(kernel2),-(rootfs2) earlyprintk=serial bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=nand read 0x2000000 0x08700000 0xF00000 && bootz 0x2000000 bootcmd_auto=stage_boot $boot_order bootcmd_custom=if run bootcmd_exec; then; else if run bootcmd_stock_1; then; else run bootcmd_stock_2; reset; fi; fi bootcmd_custom_sata=if run sata_bootcmd; then; else if run bootcmd_stock_1; then; else run bootcmd_stock_2; reset; fi; fi bootcmd_exec=run scan_disk; echo Booting from $bootdev $device ...; setenv fdt_skip_update yes; if run load_image; then if run load_dtb; then if run load_initrd; then run set_bootargs; bootz $load_image_addr $load_initrd_addr $load_dtb_addr; fi; fi; fi bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootcmd_stock_1=run set_bootargs_stock; echo Booting from NAND kernel 1 ...; nand read 0x2000000 0x00E00000 0xF00000 && bootz 0x2000000 bootcmd_stock_2=run set_bootargs_stock; echo Booting from NAND kernel 2 ...; nand read 0x2000000 0x08700000 0xF00000 && bootz 0x2000000 bootdelay=3 cacheShare=no change_boot_part=0 console=console=ttyS0,115200 core_checksum_1=e9b3248e8c69ec9ef52a8698d0835aae core_checksum_2=2773b03df8b32c243f8b84dcefa79efb curr_bootfrom=2 device_partition=0:1 devices=usb scsi disaMvPnp=no disks=0 1 2 3 dtb_file=/boot/dts/armada-380-zyxel-nas326.dtb eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:38:32:25 eth1mtu=1500 eth2addr=00:50:43:38:a6:25 eth2mtu=1500 eth3addr=00:50:43:32:a6:38 eth3mtu=1500 ethact=egiga0 ethaddr=58:8B:F3:DB:DD:3E ethmtu=1500 ethprime=egiga0 fdt_addr=2040000 fdt_skip_update=yes fdtaddr=0x1000000 fdtfile=armada-38x-modular.dtb filesize=0x6e8f80 fwversion_1=V5.21(AAZF.0) fwversion_2=V5.21(AAZF.1) ide_path=/ image_name=uImage img_checksum_1=db4be927b09d7ea9a1284d2e6f330db5 img_checksum_2=5356a1c083dfd6bc8c74bfd231aa15a6 initrd_name=uInitrd ipaddr=10.4.50.170 kernel_addr=${kernel_addr_1} kernel_addr_1=0x00000000; run bootcmd_custom; kernel_addr_2=0x08700000 kernel_addr_r=2080000 kernel_mtd_1=3 kernel_mtd_2=5 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 load_dtb=echo loading DTB $dtb_file ...; ext2load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1000000 load_image=echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/zImage load_image_addr=0x02000000 load_initrd=echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x2900000 loadaddr=0x02000000 loads_echo=0 modelid_1=B303 modelid_2=B303 mtddevname=u-boot mtddevnum=0 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:2m(u-boot),2m(env),2m(config),15m(kernel1),110m(rootfs1),15m(kernel2),-(rootfs2) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:25:a6:38 nandEcc=nfcConfig=4bitecc netbsd_en=no netmask=255.255.255.0 netretry=no next_bootfrom=2 partition=nand0,0 pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 revision_1=50967 revision_2=50984 romfile_checksum_1=4EE9 romfile_checksum_2=A762 rootpath=/srv/nfs/ sata_bootcmd=echo Booting from SATA ...; setenv fdt_skip_update yes; run sata_init; ext2load scsi 0:1 $load_image_addr /boot/zImage; ext2load scsi 0:1 $load_dtb_addr /boot/dts/armada-380-zyxel-nas326.dtb; ext2load scsi 0:1 $load_initrd_addr /boot/uInitrd; run sata_set_bootargs; bootz $load_image_addr $load_initrd_addr $load_dtb_addr sata_delay_reset=0 sata_dma_mode=yes sata_init=mw.l f1018100 20420000; mw.l f1018140 003ca800; sleep 3; scsi init sata_set_bootargs=setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial" scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "run usb_init"; setenv scan_scsi "run sata_init"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if ext2load $dev $disknum:1 $load_image_addr /boot/zImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done script_addr_r=3000000 script_name=boot.scr scsidevs=0 serial_number=S150Y46042395 serverip=10.4.50.38 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial set_bootargs_stock=setenv bootargs "console=ttyS0,115200 ubi.mtd=4,2048 rootfstype=ubifs root=ubi0:rootfs1 rw rootdelay=2" standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial sysimg_mtd_1=4 sysimg_mtd_2=6 usb0Mode=host usbActive=0 usbType=2 usb_bootcmd=echo Booting from USB ...; setenv fdt_skip_update yes; run usb_init; ext2load usb 0:1 $load_image_addr /boot/zImage; ext2load usb 0:1 $load_dtb_addr /boot/dts/armada-380-zyxel-nas326.dtb; ext2load usb 0:1 $load_initrd_addr /boot/uInitrd; run usb_set_bootargs; bootz $load_image_addr $load_initrd_addr $load_dtb_addr usb_init=mw.l f1018100 20420000; mw.l f1018140 003E8800; sleep 3; usb start usb_set_bootargs=setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial" vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 zld_checksum_1=b44f1fe16e53092068270b337dee223c zld_checksum_2=102d2dc16f397df0dddc4f1ad6380e52 Environment size: 7133/524284 bytes Marvell>> boot NAND read: device 0 offset 0x8700000, size 0xf00000 15728640 bytes read: OK * kernel: cmdline image address = 0x02000000 Starting kernel ... Power on HDD1 ... Power on HDD2 ... Power on USB ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 3.10.39 (root@SDD2SVR2) (gcc version 4.8.5 20150209 (prerelease) (crosstool-NG 1.21.0) ) #1 Fri May 26 16:47:54 CST 2017 CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: Marvell Armada 380/381/382/385/388 (Device Tree), model: Marvell Armada 380 STG-328 bootconsole [earlycon0] enabled Memory policy: ECC disabled, Data cache writealloc CPU: All CPU(s) started in SVC mode. Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=armada-nand:2m(u-boot),2m(env),2m(config),15m(kernel1),110m(rootfs1),15m(kernel2),-(rootfs2) earlyprintk=serial PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 512MB = 512MB total Memory: 504456k/504456k available, 19832k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xe0800000 - 0xfff00000 ( 503 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc081c8a8 (8275 kB) .init : 0xc081d000 - 0xc0e3cd5c (6272 kB) .data : 0xc0e3e000 - 0xc0e950e0 ( 349 kB) .bss : 0xc0e950e0 - 0xc0ee2c70 ( 311 kB) NR_IRQS:16 nr_irqs:16 16 LSP version: linux-3.10.39-2014_T3.0p7 sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms L310 cache controller enabled l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B Console: colour dummy device 80x30 Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok Setting up static identity map for 0xc063c590 - 0xc063c5e8 mvebu-pmsu: Initializing Power Management Service Unit Initializing CPU Reset module devtmpfs: initialized mvebu-soc-id: MVEBU SoC ID=0x6810, Rev=0x4 xor: measuring software checksum speed arm4regs : 2368.000 MB/sec 8regs : 1458.800 MB/sec 32regs : 1408.000 MB/sec xor: using function: arm4regs (2368.000 MB/sec) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations irq: Cannot allocate irq_descs @ IRQ194, assuming pre-allocated irq: Cannot allocate irq_descs @ IRQ226, assuming pre-allocated bio: create slab <bio-0> at 0 raid6: int32x1 203 MB/s raid6: int32x2 270 MB/s raid6: int32x4 283 MB/s raid6: int32x8 323 MB/s raid6: using algorithm int32x8 (323 MB/s) raid6: using intx1 recovery algorithm gpio-ms: gpio_dev = fe00000 (M: 254, m: 0) [kernel] gpio_request for GPIO[24] failed with error number: -517 [kernel] gpio_request for GPIO[31] failed with error number: -517 [kernel] gpio_request for GPIO[44] failed with error number: -517 mvebu-pcie pcie-controller.3: PCIe0.0: link down mvebu-pcie pcie-controller.3: PCIe1.0: link down mvebu-pcie pcie-controller.3: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe8000000] pci_bus 0000:00: root bus resource [bus 00-ff] PCI: bus0: Fast back to back transfers disabled pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring PCI: bus1: Fast back to back transfers enabled PCI: bus2: Fast back to back transfers enabled pci 0000:00:01.0: PCI bridge to [bus 01] pci 0000:00:02.0: PCI bridge to [bus 02] PCI: enabling device 0000:00:01.0 (0140 -> 0143) PCI: enabling device 0000:00:02.0 (0140 -> 0143) vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [kernel] gpio_request for GPIO[46] failed with error number: -517 [kernel] gpio_request for GPIO[49] failed with error number: -517 [kernel] gpio_request for GPIO[39] failed with error number: -517 PTP clock support registered cfg80211: Calling CRDA to update world regulatory domain Switching to clocksource armada_370_xp_clocksource NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP: reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) NFS: Registering the id_resolver key type Key type id_resolver registered [kernel] gpio_request for GPIO[46] failed with error number: -517 Key type id_legacy registered [kernel] gpio_request for GPIO[49] failed with error number: -517 Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [kernel] gpio_request for GPIO[39] failed with error number: -517 fuse init (API version 7.22) bio: create slab <bio-1> at 1 Btrfs loaded msgmni has been set to 985 async_tx: api initialized (async) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver ****** turn off all LEDs that turned on in u-boot ****** ****** blink SYS LED ****** mv_xor f1060800.xor: Marvell shared XOR driver mv_xor f1060800.xor: Marvell XOR: ( xor cpy intr ) mv_xor f1060800.xor: freeing 1 in use descriptors! mv_xor f1060800.xor: Marvell XOR: ( crc32c ) mv_xor f1060900.xor: Marvell shared XOR driver mv_xor f1060900.xor: Marvell XOR: ( xor cpy intr ) mv_xor f1060900.xor: freeing 1 in use descriptors! mv_xor f1060900.xor: Marvell XOR: ( crc32c ) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A console [ttyS0] enabled, bootconsole disabled console [ttyS0] enabled, bootconsole disabled brd: module loaded loop: module loaded ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs scsi0 : ahci_mv_platform scsi1 : ahci_mv_platform ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58 ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58 armada-nand f10d0000.nand: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC NAND device: Manufacturer ID: 0xc2, Chip ID: 0xda (Macronix NAND 256MiB 3,3V 8-bit), 256MiB, page size: 2048, OOB size: 64 Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 7 cmdlinepart partitions found on MTD device armada-nand Creating 7 MTD partitions on "armada-nand": 0x000000000000-0x000000200000 : "u-boot" 0x000000200000-0x000000400000 : "env" 0x000000400000-0x000000600000 : "config" 0x000000600000-0x000001500000 : "kernel1" 0x000001500000-0x000008300000 : "rootfs1" 0x000008300000-0x000009200000 : "kernel2" 0x000009200000-0x000010000000 : "rootfs2" m25p80 spi0.0: unrecognized JEDEC id ffffff SoC: model = 0x6810, revision = 0x4 o 3 Giga ports supported o SKB recycle supported for SWF (Disabled) o NETA acceleration mode 1 o RX Queue support: 8 Queues * 256 Descriptors o TX Queue support: 8 Queues * 532 Descriptors o GSO supported o GRO supported o Receive checksum offload supported o Transmit checksum offload supported o Driver ERROR statistics enabled o Driver INFO statistics enabled o Driver DEBUG statistics enabled port #0: is_sgmii=0, is_rgmii=1, phy_addr=1 o Loading network interface(s) for port #0: cpu_mask=0x1, tx_csum_limit=9800 o Port 0 is connected to Linux netdevice o eth0, ifindex = 2, GbE port = 0 giga p=0: mtu=1500, mac=00:50:43:02:02:01 (platform) libphy: orion_mdio_bus: probed e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI e1000: Copyright (c) 1999-2006 Intel Corporation. e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k e1000e: Copyright(c) 1999 - 2013 Intel Corporation. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-orion: EHCI orion driver orion-ehci f1058000.usb: EHCI Host Controller orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 orion-ehci f1058000.usb: irq 50, io mem 0xf1058000 orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 3.10.39 ehci_hcd usb usb1: SerialNumber: f1058000.usb hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000 usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: xHCI Host Controller usb usb2: Manufacturer: Linux 3.10.39 xhci-hcd usb usb2: SerialNumber: f10f0000.usb3 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: xHCI Host Controller usb usb3: Manufacturer: Linux 3.10.39 xhci-hcd usb usb3: SerialNumber: f10f0000.usb3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000 usb usb4: New USB device found, idVendor=1d6b, idProduct=0002 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: xHCI Host Controller usb usb4: Manufacturer: Linux 3.10.39 xhci-hcd usb usb4: SerialNumber: f10f8000.usb3 ata2: SATA link down (SStatus 0 SControl 300) hub 4-0:1.0: USB hub found hub 4-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 usb usb5: New USB device found, idVendor=1d6b, idProduct=0003 usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb5: Product: xHCI Host Controller usb usb5: Manufacturer: Linux 3.10.39 xhci-hcd usb usb5: SerialNumber: f10f8000.usb3 hub 5-0:1.0: USB hub found hub 5-0:1.0: 1 port detected usbcore: registered new interface driver usblp usbcore: registered new interface driver usb-storage mousedev: PS/2 mouse device common for all mice mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 i2c /dev entries driver md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com dm_crypt using the OCF package. cpuidle: using governor ladder sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman mmc0: SDHCI controller on f10d8000.sdhci [f10d8000.sdhci] using ADMA sdhci-pltfm: SDHCI platform and OF driver helper armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2 armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: int_coalescing(1) armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources threshold 0x2, threshold_time 0xff mvCesaInit: channels=2, session=640, queue=256 armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode cesadev_init(c0836b3c) usbcore: registered new interface driver usbhid usbhid: USB HID core driver TCP: cubic registered NET: Registered protocol family 10 sit: IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 8021q: 802.1Q VLAN Support v1.8 Key type dns_resolver registered VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 mvebu-rtc f10a3800.rtc: setting system clock to 2017-09-05 01:52:31 UTC (1504576351) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-8: WDC WD10EARS-00Y5B1, 80.00A80, max UDMA/133 ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA WDC WD10EARS-00Y 80.0 PQ: 0 ANSI: 5 ******** sd_probe: turn_off LED_HDD1 ******** ******** sd_probe: turn_on LED_HDD1 WHITE******** sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sd 0:0:0:0: [sda] Attached SCSI disk Freeing unused kernel memory: 6268K (c081d000 - c0e3c000) hotplug1110add:[/devices/soc.0/internal-regs.1/f10a8000.sata/ata1/host0/target0:0:0/0:0:0:0/block/sda][sda]Mass Storage device + ECHO=/bin/echo + RM=/bin/rm + IFCONFIG=/sbin/ifconfig + IP=/bin/ip + MOUNT=/bin/mount + MKDIR=/bin/mkdir + RMDIR=/bin/rmdir + CAT=/bin/cat + MDEV=/sbin/mdev + SETTING_PATH=/etc/settings + [ -f /etc/settings/firmware_info_path ] + cat /etc/settings/firmware_info_path + BASE_PATH=/firmware + BASE_PATH=/firmware + NAND_PATH=/firmware/mnt/nand + DISK_PATH=/firmware/mnt/sysdisk + INFO_PATH=/firmware/mnt/info + MRD_MAC=/firmware/sbin/mrd_mac + INFO_PRINTENV=/firmware/sbin/info_printenv + INFO_SETENV=/firmware/sbin/info_setenv + IMG_PATH=/ram_bin + USB_PATH=/mnt/partnerkey + awk -F= {print $2} + /firmware/sbin/info_printenv curr_bootfrom + CURR_BOOTFROM=2 + awk -F= {print $2} + /firmware/sbin/info_printenv next_bootfrom + NEXT_BOOTFROM=2 + [ 2 != 2 ] + /bin/echo -e \033[031m*** Stage 1: Setup system and device drivers ***\033[0m *** Stage 1: Setup system and device drivers *** + setLED SYS WHITE BLINK Fail to open gpio device + /bin/mount -t proc /proc /proc + /bin/mount -t sysfs /sys /sys + /bin/mount -t usbfs none /proc/bus/usb mount: mount point /proc/bus/usb does not exist + /bin/mount -t devpts devpts /dev/pts + awk {print $1} + grep gpio + cat /proc/devices + mknod -m 644 /dev/gpio c 254 0 + awk -F= {print $2} + /firmware/sbin/info_printenv fwversion_2 + FWVERSION=V5.21(AAZF.1) + awk -F= {print $2} + /firmware/sbin/info_printenv revision_2 + REVISION=50984 + awk -F= {print $2} + /firmware/sbin/info_printenv modelid_2 + MODELID=B303 + awk -F= {print $2} + /firmware/sbin/info_printenv core_checksum_2 + CORE_CHECKSUM=2773b03df8b32c243f8b84dcefa79efb + awk -F= {print $2} + /firmware/sbin/info_printenv zld_checksum_2 + ZLD_CHECKSUM=102d2dc16f397df0dddc4f1ad6380e52 + awk -F= {print $2} + /firmware/sbin/info_printenv romfile_checksum_2 + ROMFILE_CHECKSUM=A762 + awk -F= {print $2} + /firmware/sbin/info_printenv img_checksum_2 + IMG_CHECKSUM=5356a1c083dfd6bc8c74bfd231aa15a6 + [ ! -d /firmware/mnt/info ] + /bin/mkdir -p /firmware/mnt/info + echo V5.21(AAZF.1) + echo 50984 + echo B303 + echo 2773b03df8b32c243f8b84dcefa79efb + echo 102d2dc16f397df0dddc4f1ad6380e52 + echo A762 + echo 5356a1c083dfd6bc8c74bfd231aa15a6 + echo /sbin/mdev + /sbin/mdev -s + /bin/echo 32769 42768 + /bin/echo 8192 + /bin/echo 100 + /bin/echo 5 + /bin/echo 10 + /bin/echo 512 87380 2048000 + /bin/echo 512 65536 2048000 + /bin/echo 524288 + /bin/echo 524288 + /sbin/ifconfig eth0 down + /firmware/sbin/mrd_mac eth0 + /sbin/ifconfig eeth0: mac address changed th0 hw ether 58:8B:F3:DB:DD:3E + /bin/ip link set dev eth0 name egiga0 + /sbin/ifconfig egiga0 up bmPoolId = 0 has unknown buf_size pool #0: pkt_size=1536, buf_size=1600 - 4096 of 4096 buffers added egiga0: started IPv6: ADDRCONF(NETDEV_UP): egiga0: link is not ready + /sbin/ifconfig lo add 127.0.0.1 netmask 255.0.0.0 + /sbin/ifconfig lo up + /sbin/ethtool -K egiga0 gso on + /sbin/ethtool -s egiga0 advertise 0x2f Cannot set new settings: Invalid argument + /sbin/ethtool -s egiga0 autoneg on Cannot set new settings: Invalid argument not setting autoneg + /sbin/rtcAccess show + rtc_time1=2017-09-05 01:52:43 + sleep 1 + /sbin/rtcAccess show + rtc_time2=2017-09-05 01:52:45 + [ 2017-09-05 01:52:43 = 2017-09-05 01:52:45 ] + awk -F- {print $1} + echo 2017-09-05 01:52:43 + year1=2017 + awk -F- {print $1} + echo 2017-09-05 01:52:45 + year2=2017 + awk -F- {print $1} + /sbin/rtcAccess show + year3=2017 + [ 2017 != 2017 ] + /sbin/rtcAccess rtctosys + echo 2 + echo 80 + /linuxrc + . /etc/profile + SETTING_PATH=/etc/settings + [ -f /etc/settings/firmware_info_path ] + cat /etc/settings/firmware_info_path + BASE_PATH=/firmware + PATH=/bin:/sbin:/usr/bin:/usr/sbin:/usr/local/bin:/usr/local/sbin:/firmware/sbin:/usr/local/zy-pkgs/bin:/firmware/htp + export PATH + LD_LIBRARY_PATH=/lib:/usr/lib:/usr/lib/private + export LD_LIBRARY_PATH + ECHO=/bin/echo + CAT=/bin/cat + RM=/bin/rm + MOUNT=/bin/mount + UMOUNT=/bin/umount + IP=/bin/ip + IFCONFIG=/sbin/ifconfig + SED=/bin/sed + MKDIR=/bin/mkdir + RMDIR=/bin/rmdir + AWK=/bin/awk + MD5SUM=/sbin/md5sum + REBOOT=/sbin/reboot + BUZZERC=/sbin/buzzerc + LN=/bin/ln + INSMOD=/sbin/insmod + RMMOD=/sbin/rmmod + LSMOD=/sbin/lsmod + DEPMOD=/sbin/depmod + NAND_PATH=/firmware/mnt/nand + DISK_PATH=/firmware/mnt/sysdisk + INFO_PATH=/firmware/mnt/info + HTP_PATH=/firmware/htp + IMG_PATH=/ram_bin + USB_PATH=/mnt/partnerkey + [ -f /etc/settings/config_on_nand_path ] + cat /etc/settings/config_on_nand_path + CONF_PATH=/etc/zyxel + CONFIG_MTD_NUM=2 + CONFIG_MTD=/dev/mtd2 + CONFIG_MTD_BLOCK=/dev/mtdblock2 + GET_MAC_MCU=/sbin/get_mac_mcu.sh + WRITE_MAC_MCU=/sbin/write_mac_mcu.sh + INFO_PRINTENV=/firmware/sbin/info_printenv + INFO_SETENV=/firmware/sbin/info_setenv + MRD_MAC=/firmware/sbin/mrd_mac + MRD_MODEL=/firmware/sbin/mrd_model + NAND_FS_TYPE=ubifs + awk -F= {print $2} + /firmware/sbin/info_printenv curr_bootfrom + CURR_BOOTFROM=2 + [ 2 = 1 ] + IMG_MTD=6 + NEW_ROOT= + SYSINIT_PASSWD=$1$$4eHwTd8s1.UjO3wA36fmX1 + SYSINIT_PATH=/mnt/sysinit + /firmware/sbin/mrd_model -p + MODEL_ID=B303 + RAM_BOOT_ABLE=YES + echo 1 + rescan_lost_scsi_device + wc -l + ls /sys/class/scsi_host + hostNum=2 + cut -c 5 + ls /sys/class/scsi_host + hostIdLst=0 1 + hddId=2 + cat /proc/hdd2_detect cat: can't open '/proc/hdd2_detect': No such file or directory + [ == 1 ] + hddId=1 + cat /proc/hdd1_detect cat: can't open '/proc/hdd1_detect': No such file or directory + [ == 1 ] + /bin/echo -e \033[031m*** Stage 2: Prepare the root file system ***\033[0m *** Stage 2: Prepare the root file system *** + /bin/echo -e \033[033mMount system partition...\033[0m Mount system partition... + /bin/mkdir -p /firmware/mnt/nand + ls -l /dev/ubi_ctrl crw-rw---- 1 root root 10, 59 Sep 5 01:52 /dev/ubi_ctrl + [ ! -e /dev/ubi_ctrl ] + check_and_run_usbkey + USB_CHECK_FILE=/mnt/partnerkey/nas3xx_check_file + grep sd + ls /sys/block/ + any_usb=sda + /bin/echo sda sda + [ -n sda ] + /bin/mkdir /mnt/partnerkey + /bin/echo checking sda checking sda + grep -c ? + grep ^/dev/sda + fdisk -l /dev/sda + qmark_num=0 + grep ^/dev/sda + fdisk -l /dev/sda + partition_num=/dev/sda1 * 2048 1953523711 1953521664 931.5G 83 Linux + [ 0 == 4 ] + [ /dev/sda1 * 2048 1953523711 1953521664 931.5G 83 Linux == ] + sed -n 1p + awk {print $1} + grep ^/dev/sda + fdisk -l /dev/sda + mnt_point=/dev/sda1 + /bin/echo Trying to mount /dev/sda1 Trying to mount /dev/sda1 + /bin/mount -o iocharset=utf8,shortname=mixed /dev/sda1 /mnt/partnerkey EXT4-fs (sda1): Unrecognized mount option "iocharset=utf8" or missing value mount: wrong fs type, bad option, bad superblock on /dev/sda1, missing codepage or helper program, or other error In some cases usefuUBI: attaching mtd6 to ubi6 l info is found in syslog - try dmesg | tail or so. + grep /mnt/partnerkey + /bin/cat /proc/mounts + mount_SUC= + [ != ] + /bin/echo Fail to mount /dev/sda1 Fail to mount /dev/sda1 + /bin/rmdir /mnt/partnerkey + ls -l /dev/ubi_ctrl crw-rw---- 1 root root 10, 59 Sep 5 01:52 /dev/ubi_ctrl + ubidetach -d 0 ubidetach: error!: cannot remove ubi0 error 22 (Invalid argument) + ubiattach -m 6 -d 6 UBI: scanning is finished UBI: attached mtd6 (name "rootfs2", size 110 MiB) to ubi6 UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 UBI: good PEBs: 872, bad PEBs: 8, corrupted PEBs: 0 UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 UBI: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 3452188652 UBI: available PEBs: 32, total reserved PEBs: 840, PEBs reserved for bad PEB handling: 32 UBI: background thread "ubi_bgt6d" started, PID 1338 UBI device number 6, total 872 LEBs (110723072 bytes, 105.6 MiB), available 32 LEBs (4063232 bytes, 3.9 MiB), LEB size 126976 bytes (124.0 KiB) + ls -l /dev/ubi6 /dev/ubi6_0 /dev/ubi_ctrl crw-rw---- 1 root root 249, 0 Sep 5 01:52 /dev/ubi6 crw-rw---- 1 root root 249, 1 Sep 5 01:52 /dev/ubi6_0 crw-rw---- 1 root root 10, 59 Sep 5 01:52 /dev/ubi_ctrl + [ ! -e /dev/ubi6 ] + ls -l /dev/ubi6 /dev/ubi6_0 /dev/ubi_ctrl crw-rw---- 1 root root 249, 0 Sep 5 01:52 /dev/ubi6 crw-rw---- 1 root root 249, 1 Sep 5 01:52 UBIFS: mounted UBI device 6, volume 0, name "ubi_rootfs2", R/O mode /dev/ubi6_0 crwUBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes -rw---- 1 rooUBIFS: FS size: 100691968 bytes (96 MiB, 793 LEBs), journal size 5079040 bytes (4 MiB, 40 LEBs) t root UBIFS: reserved for root: 4755930 bytes (4644 KiB) 10, 59 Sep 5 UBIFS: media format: w4/r0 (latest is w4/r0), UUID BC7D1F8A-CB46-4006-85B8-29548DDE9947, small LPT model 01:52 /dev/ubi_ctrl + mount -t ubifs -o ro ubi6:ubi_rootfs2 /firmware/mnt/nand + [ ! -e /firmware/mnt/nand/sysdisk.img.gz ] + cat /proc/htp_pin cat: can't open '/proc/htp_pin': No such file or directory + HTP_PIN= + [ == 1 ] sh: 1: unknown operand + /bin/storage_asm_mntfw_swap.sh /firmware/mnt/sysdisk can not found fw raid uuid can not found swap raid uuid /sbin/mdadm --grow /dev/md0 --raid-devices=2 --force mdadm: /dev/md0 is not an active md array - aborting /sbin/mdadm --grow /dev/md1 --raid-devices=2 --force mdadm: /dev/md1 is not an active md array - aborting storage_asm_mntfw_swap.sh can not swap on /dev/md1 + Flag_HD_Exists=1 + echo 1 1 + [ 1 == 0 ] + echo WARNING: No valid partition on HDD or no HDD plugged! WARNING: No valid partition on HDD or no HDD plugged! + [ YES == YES ] + BOOTDEV=RAM + export BOOTDEV + [ RAM == RAM ] + echo WARNING: No valid partition on HDD or no HDD plugged WARNING: No valid partition on HDD or no HDD plugged + echo Boot from RAM disk Boot from RAM disk + /bin/mkdir -p /firmware/mnt/sysdisk + /bin/mount -t ramfs none /firmware/mnt/sysdisk + gzip -cd /firmware/mnt/nand/sysdisk.img.gz + [ 0 -ne 0 ] + grep change_boot_part + /firmware/sbin/info_printenv + IS_CHANGE_BOOT_PART_EXIST=change_boot_part=0 + [ change_boot_part=0 != ] + awk -F= {print $2} + /firmware/sbin/info_printenv change_boot_part + CHANGE_BOOT_PART=0 + [ 0 == 1 ] + /bin/mount -o remount,ro /firmware/mnt/sysdisk + [ -e /firmware/mnt/sysdiskEXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem /mount.sda1.rw.fEXT4-fs (loop0): mounted filesystem without journal. Opts: (null) lag ] + [ -f /firmware/mnt/sysdisk/sysdisk.img ] + echo -e \033[033mMount system disk image ...\033[0m Mount system disk image ... + /bin/mkdir -p /ram_bin + /bin/mount -t ext2 -o loop,ro /firmware/mnt/sysdisk/sysdisk.img /ram_bin + [ 0 -ne 0 ] + /bin/mount --bind /ram_bin/usr /usr + /bin/mount --bind /ram_bin/lib/security /lib/security + /bin/mount --bind /ram_bin/lib/modules /lib/modules + /bin/mount --bind /ram_bin/lib/locale /lib/locale + cp -a /ram_bin/bin/lld2d /ram_bin/bin/sg_mapUBI: attaching mtd2 to ubi2 /bin/ + cp -a /ram_bin/sbin/DAV_httpd /ram_bin/sbin/controlSSHUBI: scanning is finished .sh /ram_bin/sbin/dosfsck /ram_bin/sbin/exfatfscUBI warning: print_rsvd_warning: cannot reserve enough PEBs for bad PEB handling, reserved 12, need 40 k /ram_bin/sbin/fsck.fat /ram_biUBI: attached mtd2 (name "config", size 2 MiB) to ubi2 n/sbin/fsck.hfs UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes /ram_bin/sbin/ipUBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 notify /ram_bin/UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 sbin/ipnotify_exUBI: good PEBs: 16, bad PEBs: 0, corrupted PEBs: 0 ec.sh /ram_bin/sUBI: user volume: 0, internal volumes: 1, max. volumes count: 128 bin/makekey /ramUBI: max/mean erase counter: 1/1, WL threshold: 4096, image sequence number: 3429425135 _bin/sbin/makepwUBI: available PEBs: 0, total reserved PEBs: 16, PEBs reserved for bad PEB handling: 12 d /ram_bin/sbin/UBI: background thread "ubi_bgt2d" started, PID 1436 mdir /ram_bin/sbin/mkdosfs /ram_bin/sbin/mkexfatfs /ram_bin/sbinUBIFS error (pid 1438): ubifs_mount: cannot open "ubi2:ubi_config", error -19 /mkfs.fat /ram_bin/sbin/monitord /ram_bin/sbin/mount.exfat-fuse /ram_bin/sbin/mount.fuse /ram_bin/sbin/mtools /ram_bin/sbin/sftp-server /ram_bin/sbin/ssh /ram_bin/sbin/ssh-keygUBI: detaching mtd2 from ubi2 en /ram_bin/sbinUBI: mtd2 is detached from ubi2 /sshd /ram_bin/sbin/target.init /ram_bin/sbin/targetcli /ram_bin/sbin/targetcli-ng /ram_bin/sbin/usbzync /ram_bin/sbin/usbzync.sh /ram_bin/sbin/usbzync_rm_rf.sh /sbin/ + /bin/mkdir /tmp/tmpfs + /bin/mount -t tmpfs /dev/ram0 /tmp/tmpfs -o size=5m + /bin/mkdir /tmp/tmpfs/usr_etc + /bin/cp -a /usr/local/etc/mt-daapd /usr/local/etc/mt-daapd.conf /tmp/tmpfs/usr_etc + /bin/mount --bind /tmp/tmpfs/usr_etc /usr/local/etc + /bin/mkdir /tmp/tmpfs/usr_var + /bin/mount --bind /tmp/tmpfs/usr_var /usr/local/var mount: mount point /usr/local/var does not exist + /bin/mkdir -p /tmp/zyxel + cp -a /etc/zyxel/BackupPlanner /etc/zyxel/conf /etc/zyxel/dservice.disable /etc/zyxel/hd-idle.conf /etc/zyxel/pkg_conf /etc/zyxel/storage /etc/zyxel/webdav /etc/zyxel/zyfw /tmp/zyxel + ubiattach -m 2 -d 2 UBI device number 2, total 16 LEBs (2031616 bytes, 1.9 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) + ls -l /dev/ubi2 /dev/ubi6 /dev/ubi6_0 /dev/ubi_ctrl crw-rw---- 1 root root 248, 0 Sep 5 01:52 /dev/ubi2 crw-rw---- 1 root root 249, 0 Sep 5 01:52 /dev/ubi6 crw-rw---- 1 root root 249, 1 Sep 5 01:52 /dev/ubi6_0 crw-rw---- 1 root root 10, 59 Sep 5 01:52 /dev/ubi_ctrl + [ ! -e /dev/ubi2 ] + /bin/mount -t ubifs ubi2:ubi_config /etc/zyxel mount: unknown filesystem type 'ubifs' + [ 32 != 0 ] + /bin/echo mount /etc/zyxel failed mount /etc/zyxel failed + prepare_config_partition + [ /etc/zyxel != ] + echo --- remove all files in /etc/zyxel --- remove all files in /etc/zyxel + rm -rf /etc/zyxel/BackupPlanner /etc/zyxel/conf /etc/zyxel/dservice.disable /etc/zyxel/hd-idle.conf /etc/zyxel/pkg_conf /etc/zyxel/storage /etc/zyxel/webdav /etc/zyxel/zyfw + echo --- umount /etc/zyxel --- umount /etc/zyxel + umount /etc/zyxel umount: /etc/zyxel: not mounted + echo --- remove "ubi_config" volume --- remove "ubi_config" volume + ubirmvol /dev/ubi2 -N ubi_config ubirmvol: error!: cannot find UBI volume "ubi_config" error 2 (No such file or directory) + echo --- detach ubi2 from /dev/mtd2 --- detach ubi2 from /dev/mtd2 + ubidetach -m 2 + sleep 1 + [ 0 == 0 ] + echo --- flash_erase /dev/mtd2 0 0 --- flash_erase /dev/mtd2 0 0 + flash_erase /dev/mtd2 0 0 ErasUBI: attaching mtd2 to ubi2complete ing 128 Kibyte @ 20000 -- 6 % cUBI: scanning is finished ErasingUBI: empty MTD device detected Erasing 128 Kibyte @ a0000 -- 31UBI warning: print_rsvd_warning: cannot reserve enough PEBs for bad PEB handling, reserved 12, need 40 Erasing 128 Kibyte UBI: attached mtd2 (name "config", size 2 MiB) to ubi2 @ c0000 -- 37 % UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ErasinUBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 g 128 Kibyte @ eUBI: VID header offset: 2048 (aligned 2048), data offset: 4096 0000 -- 43 % comUBI: good PEBs: 16, bad PEBs: 0, corrupted PEBs: 0 Erasing 1UBI: user volume: 0, internal volumes: 1, max. volumes count: 128 28 Kibyte @ 1000UBI: max/mean erase counter: 0/0, WL threshold: 4096, image sequence number: 155612257 00 -- 50 % complUBI: available PEBs: 0, total reserved PEBs: 16, PEBs reserved for bad PEB handling: 12 Erasing 128UBI: background thread "ubi_bgt2d" started, PID 1455 Erasing 128 Kibyte @ 140000 -UBIFS error (pid 1457): ubifs_mount: cannot open "ubi2:ubi_config", error -19 Erasing 128 Kibyte @ 1e0000 -- 100 % complete + echo --- mount /etc/zyxel back --- mount /etc/zyxel back + ubiattach -m 2 -d 2 UBI device number 2, total 16 LEBs (2031616 bytes, 1.9 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) + ubimkvol /dev/ubi2 -N ubi_config -m ubimkvol: error!: UBI device does not have free logical eraseblocks + /bin/mount -t ubifs ubi2:ubi_config /etc/zyxel mount: unknown filesystem type 'ubifs' + /bin/cp -af /tmp/NTFS driver 2.1.30 [Flags: R/O MODULE]. zyxel /etc/ + rm -rf /tmp/zyxel + [ -f /etc/zyxel/zyconf.tgz ]tntfs: module license 'Commercial. For support email ntfs-support@tuxera.com.' taints kernel. + /bin/chmod 7Disabling lock debugging due to kernel taint 77 /etc/zyxel + /ram_bin/etc/inTuxera NTFS driver 3015.1.29 [Flags: R/W MODULE]. it.d/rcS2 Start rcS2 of ZyXEL style *** Stage 3: Start services on HDD *** PPP generic driver version 2.4.2 PPP MPPE Compression module registered PPP Deflate Compression module registered NET: Registered protocol family 24 PPP BSD Compression module registered HTP finished, reUBI error: ubi_attach_mtd_dev: mtd2 is already attached to ubi2 -mount /etc/zyxel ubiattach: erUBIFS error (pid 1500): ubifs_mount: cannot open "ubi2:ubi_config", error -19 ror!: cannot attach mtd2 error 17 (File exists) mount: unknown filesystem type 'ubifs' Press ENTER to continue... Starting zylogd... zylog starts. Starting uamd... Starting WSGI server... CherryPy Checker: The Application mounted at '' has an empty config. [05/Sep/2017:01:53:02] [network_common.py.pre](check_link_status)(278): the interface bond0 is down or unusable [05/Sep/2017:01:53:04] [network_common.py.pre](check_link_status)(278): the interface bond0 is down or unusable [05/Sep/2017:01:53:04] [network_main_model_back.py.pre](ipv6_dhcp_static_setting_apply)(229): The interface bond0 is down! [05/Sep/2017:01:53:04] [network_common.py.pre](check_link_status)(278): the interface egiga1 is down or unusable [05/Sep/2017:01:53:06] [network_common.py.pre](check_link_status)(278): the interface egiga1 is down or unusable [05/Sep/2017:01:53:06] [network_main_model_back.py.pre](ipv6_dhcp_static_setting_apply)(229): The interface egiga1 is down! [05/Sep/2017:01:53:08] [network_main_model_back.py.pre](ipv6_dhcp_static_setting_apply)(229): The interface egiga0 is down! [05/Sep/2017:01:53:09] [network_main_model_front.py.pre](apache_config_setting)(627): There is no statement '#WebService Start#' in httpd_zld.conf. keep going... killall: pure-ftpd: no process killed no printer device detected. Usage: umount [-hV] umount -a [options] umount [options] <source> | <directory> Options: -a, --all unmount all filesystems -A, --all-targets unmount all mountpoints for the given device in the current namespace -c, --no-canonicalize don't canonicalize paths -d, --detach-loop if mounted loop device, also free this loop device --fake dry run; skip the umount(2) syscall -f, --force force unmount (in case of an unreachable NFS system) -i, --internal-only don't call the umount.<type> helpers -n, --no-mtab don't write to /etc/mtab -l, --lazy detach the filesystem now, clean up things later -O, --test-opts <list> limit the set of filesystems (use with -a) -R, --recursive recursively unmount a target with all its children -r, --read-only in case unmounting fails, try to remount read-only -t, --types <list> limit the set of filesystem types -v, --verbose say what is being done -h, --help display this help and exit -V, --version output version information and exit For more details see umount(8). Usage: umount [-hV] umount -a [options] umount [options] <source> | <directory> Options: -a, --all unmount all filesystems -A, --all-targets unmount all mountpoints for the given device in the current namespace -c, --no-canonicalize don't canonicalize paths -d, --detach-loop if mounted loop device, also free this loop device --fake dry run; skip the umount(2) syscall -f, --force force unmount (in case of an unreachable NFS system) -i, --internal-only don't call the umount.<type> helpers -n, --no-mtab don't write to /etc/mtab -l, --lazy detach the filesystem now, clean up things later -O, --test-opts <list> limit the set of filesystems (use with -a) -R, --recursive recursively unmount a target with all its children -r, --read-only in case unmounting fails, try to remount read-only -t, --types <list> limit the set of filesystem types -v, --verbose say what is being done -h, --help display this help and exit -V, --version output version information and exit For more details see umount(8). BusyBox v1.19.4 (2017-05-26 16:39:12 CST) multi-call binary. Usage: rmdir [OPTIONS] DIRECTORY... No more ZySH daemon and client... argv[0]=/usr/sbin/zylog_config argv[1]=mail argv[2]=1 argv[3]=subject argv[4]=NAS326 Log Report mail server'1' subject:NAS326 Log Report argv[0]=/usr/sbin/zylog_config argv[1]=mail argv[2]=1 argv[3]=schedule argv[4]=hourly mail server '1' schedule is : hourly Starting "/etc/init.d/zypkg_controller.sh". Starting to set up zy-pkgs environment ... -> No volume exists now. zy-pkgs will not work. Starting smbd... Starting nmbd... Starting NSU Agent... Starting AFP... avahi-daemon netatalk. There is no usable system volume! Do nothing... GMT offset=28800s setting system time zone to tz_minuteswest=-480 killall: hd-idle: no process killed schedule_controller is already running now. setLED COPY OFF led_state_map_addr = 400 setLED USB OFF led_state_map_addr = 300 Starting app_wd... Update zypkg list There is no sysvol "/i-data/.system" ===> Generate zysync server config ... ===> Generating volume list ... ===> Generating zysync config file ... rm: can't remove '/tmp/zysync_modules': No such file or directory ===> Starting zysync server ... [INFO]: Starting server mode ... Done ===> Generating stunnel server config file ... ===> Starting stunnel server ... [.] stunnel 5.02 on arm-unknown-linux-gnu platform [.] Compiled/running with OpenSSL 1.0.2h 3 May 2016 [.] Threading:FORK Sockets:POLL,IPv6 SSL:FIPS [ ] errno: (*__errno_location ()) [.] Reading configuration from file /etc/stunneld.conf [.] FIPS mode disabled [ ] Compression disabled [ ] Snagged 64 random bytes from //.rnd [ ] Wrote 1024 new random bytes to //.rnd [ ] PRNG seeded successfully [ ] Initializing service [szysync] [ ] Loading cert from file: /etc/zyxel/BackupPlanner/zysync/zysync.cert [ ] Loading key from file: /etc/zyxel/BackupPlanner/zysync/zysync.key [:] Insecure file permissions on /etc/zyxel/BackupPlanner/zysync/zysync.key [ ] Private key check succeeded [ ] DH initialization [ ] Could not load DH parameters from /etc/zyxel/BackupPlanner/zysync/zysync.cert [ ] Using hardcoded DH parameters [ ] DH initialized with 2048-bit key [ ] ECDH initialization [ ] ECDH initialized with curve prime256v1 [ ] SSL options set: 0x01000004 [.] Configuration successful [ ] Service [szysync] (FD=6) bound to 0.0.0.0:9527 [!] Cannot open log file: /i-data/.system/stunneld.log [ ] Closing service [szysync] [ ] Service [szysync] closed (FD=6) [ ] Sessions cached before flush: 0 [ ] Sessions cached after flush: 0 [ ] Service [szysync] closed Done [ ok ] The Linux SCSI Target is already stopped [warn] Creating missing directory /var/target/pr ... (warning). [warn] Creating missing directory /var/target/alua ... (warning). [info] The Linux SCSI Target looks properly installed. [warn] The configfs filesystem was not mounted, consider adding it to fstab ... (warning). Rounding down aligned max_sectors from 4294967295 to 4294967288 [info] Loaded core module target_core_file. [warn] Core module target_core_mod already loaded ... (warning). [info] Loaded fabric module iscsi_target_mod. [warn] Startup config /etc/target/scsi_target.lio is empty, skipping ... (warning). [ ok ] Started The Linux SCSI Target 2017/09/05 09:53:21 [ipnotify] : execute ipnotify STARTUP [ipnotify_exec.sh]: ******** run ipnotify_exec.sh STARTUP******** [05/Sep/2017:09:53:22] [network_common.py.pre](check_link_status)(278): the interface bond0 is down or unusable [05/Sep/2017:09:53:22] [network_common.py.pre](check_link_status)(278): the interface bond1 is down or unusable [05/Sep/2017:09:53:22] [network_common.py.pre](check_link_status)(278): the interface egiga1 is down or unusable the interface egiga0 is down or unusable [05/Sep/2017:09:53:22] [network_common.py.pre](check_link_status)(278): the interface bond0 is down or unusable [05/Sep/2017:09:53:22] [network_common.py.pre](check_link_status)(278): the interface bond1 is down or unusable [05/Sep/2017:09:53:22] [network_common.py.pre](check_link_status)(278): the interface egiga1 is down or unusable [05/Sep/2017:09:53:22] [network_common.py.pre](check_link_status)(278): the interface bond0 is down or unusable [05/Sep/2017:09:53:22] [network_common.py.pre](check_link_status)(278): the interface bond1 is down or unusable [05/Sep/2017:09:53:22] [network_common.py.pre](check_link_status)(278): the interface egiga1 is down or unusable Device "egiga1" does not exist. killall: httpd: no process killed killall: httpd: no process killed ---------------------------------------------- admin /i-data/sysvol/admin doesn't exist. Skip it. ---------------------------------------------- music /i-data/sysvol/music doesn't exist. Skip it. ---------------------------------------------- photo /i-data/sysvol/photo doesn't exist. Skip it. ---------------------------------------------- video /i-data/sysvol/video doesn't exist. Skip it. ===> Stopping crond ... ===> Starting crond ... core_checksum : 2773b03df8b32c243f8b84dcefa79efb fwversion : V5.21(AAZF.1) img_checksum : 5356a1c083dfd6bc8c74bfd231aa15a6 modelid : B303 revision : 50984 romfile_checksum : A762 zld_checksum : 102d2dc16f397df0dddc4f1ad6380e52 OK led_state_map_addr = 6 Please press Enter to activate this console. httpd[3015]: [warn] Init: Session Cache is not configured [hint: SSLSessionCache] httpd[3015]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?) httpd[3015]: [warn] RSA server certificate CommonName (CN) `NAS326' does NOT match server name!? httpd[3015]: [error] mod_auth_zyxel: initialized. httpd[3048]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?) httpd[3048]: [warn] RSA server certificate CommonName (CN) `NAS326' does NOT match server name!? httpd[3048]: [error] mod_auth_zyxel: initialized.
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's September 04, 2017 06:14PM |
Admin Registered: 13 years ago Posts: 18,575 |
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's September 04, 2017 08:41PM |
Admin Registered: 13 years ago Posts: 18,575 |
./kwboot -t -B 115200 /dev/ttyUSB3 -d
setenv change_boot_part 1 setenv next_bootfrom 1 boot
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's September 05, 2017 05:12PM |
Registered: 6 years ago Posts: 23 |
setenv change_boot_part 1 setenv next_bootfrom 1
Not detected suspend to RAM indication BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01-svn48023 (Oct 13 2015 - 09:25:56) Marvell version: 2014_T3.0p6 Board: RD-NAS-88F6820-DDR3 SoC: MV88F6810 Rev A0 running 1 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 250 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB Map: Code: 0x1fed0000:0x1ff95d60 BSS: 0x1ffef2b4 Stack: 0x1f9cff20 Heap: 0x1f9d0000:0x1fed0000 U-Boot Environment: 0x00200000:0x00280000 (NAND) NAND: 256 MiB MMC: mv_sdh: 0 *** Booting kernel from kernel 2 @0x08700000 *** USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | 0x01 | egiga0 [PRIME] Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x8700000, size 0xf00000 15728640 bytes read: OK * kernel: cmdline image address = 0x02000000 Starting kernel ... Power on HDD1 ... Power on HDD2 ... Power on USB ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 3.10.39 (root@SDD2SVR2) (gcc version 4.8.5 20150209 (prerelease) (crosstool-NG 1.21.0) ) #1 Fri May 26 16:47:54 CST 2017 CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: Marvell Armada 380/381/382/385/388 (Device Tree), model: Marvell Armada 380 STG-328 bootconsole [earlycon0] enabled Memory policy: ECC disabled, Data cache writealloc CPU: All CPU(s) started in SVC mode. Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=armada-nand:2m(u-boot),2m(env),2m(config),15m(kernel1),110m(rootfs1),15m(kernel2),-(rootfs2) earlyprintk=serial PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 512MB = 512MB total Memory: 504456k/504456k available, 19832k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xe0800000 - 0xfff00000 ( 503 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc081c8a8 (8275 kB) .init : 0xc081d000 - 0xc0e3cd5c (6272 kB) .data : 0xc0e3e000 - 0xc0e950e0 ( 349 kB) .bss : 0xc0e950e0 - 0xc0ee2c70 ( 311 kB) NR_IRQS:16 nr_irqs:16 16 LSP version: linux-3.10.39-2014_T3.0p7 sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms L310 cache controller enabled l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B Console: colour dummy device 80x30 Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok Setting up static identity map for 0xc063c590 - 0xc063c5e8 mvebu-pmsu: Initializing Power Management Service Unit Initializing CPU Reset module devtmpfs: initialized mvebu-soc-id: MVEBU SoC ID=0x6810, Rev=0x4 xor: measuring software checksum speed arm4regs : 2368.000 MB/sec 8regs : 1458.800 MB/sec 32regs : 1408.000 MB/sec xor: using function: arm4regs (2368.000 MB/sec) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations irq: Cannot allocate irq_descs @ IRQ194, assuming pre-allocated irq: Cannot allocate irq_descs @ IRQ226, assuming pre-allocated bio: create slab <bio-0> at 0 raid6: int32x1 203 MB/s raid6: int32x2 270 MB/s raid6: int32x4 283 MB/s raid6: int32x8 323 MB/s raid6: using algorithm int32x8 (323 MB/s) raid6: using intx1 recovery algorithm gpio-ms: gpio_dev = fe00000 (M: 254, m: 0) [kernel] gpio_request for GPIO[24] failed with error number: -517 [kernel] gpio_request for GPIO[31] failed with error number: -517 [kernel] gpio_request for GPIO[44] failed with error number: -517 mvebu-pcie pcie-controller.3: PCIe0.0: link down mvebu-pcie pcie-controller.3: PCIe1.0: link down mvebu-pcie pcie-controller.3: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe8000000] pci_bus 0000:00: root bus resource [bus 00-ff] PCI: bus0: Fast back to back transfers disabled pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring PCI: bus1: Fast back to back transfers enabled PCI: bus2: Fast back to back transfers enabled pci 0000:00:01.0: PCI bridge to [bus 01] pci 0000:00:02.0: PCI bridge to [bus 02] PCI: enabling device 0000:00:01.0 (0140 -> 0143) PCI: enabling device 0000:00:02.0 (0140 -> 0143) vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [kernel] gpio_request for GPIO[46] failed with error number: -517 [kernel] gpio_request for GPIO[49] failed with error number: -517 [kernel] gpio_request for GPIO[39] failed with error number: -517 PTP clock support registered cfg80211: Calling CRDA to update world regulatory domain Switching to clocksource armada_370_xp_clocksource NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP: reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) NFS: Registering the id_resolver key type Key type id_resolver registered [kernel] gpio_request for GPIO[46] failed with error number: -517 Key type id_legacy registered [kernel] gpio_request for GPIO[49] failed with error number: -517 Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [kernel] gpio_request for GPIO[39] failed with error number: -517 fuse init (API version 7.22) bio: create slab <bio-1> at 1 Btrfs loaded msgmni has been set to 985 async_tx: api initialized (async) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver ****** turn off all LEDs that turned on in u-boot ****** ****** blink SYS LED ****** mv_xor f1060800.xor: Marvell shared XOR driver mv_xor f1060800.xor: Marvell XOR: ( xor cpy intr ) mv_xor f1060800.xor: freeing 1 in use descriptors! mv_xor f1060800.xor: Marvell XOR: ( crc32c ) mv_xor f1060900.xor: Marvell shared XOR driver mv_xor f1060900.xor: Marvell XOR: ( xor cpy intr ) mv_xor f1060900.xor: freeing 1 in use descriptors! mv_xor f1060900.xor: Marvell XOR: ( crc32c ) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A console [ttyS0] enabled, bootconsole disabled console [ttyS0] enabled, bootconsole disabled brd: module loaded loop: module loaded ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs scsi0 : ahci_mv_platform scsi1 : ahci_mv_platform ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58 ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58 armada-nand f10d0000.nand: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC NAND device: Manufacturer ID: 0xc2, Chip ID: 0xda (Macronix NAND 256MiB 3,3V 8-bit), 256MiB, page size: 2048, OOB size: 64 Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 7 cmdlinepart partitions found on MTD device armada-nand Creating 7 MTD partitions on "armada-nand": 0x000000000000-0x000000200000 : "u-boot" 0x000000200000-0x000000400000 : "env" 0x000000400000-0x000000600000 : "config" 0x000000600000-0x000001500000 : "kernel1" 0x000001500000-0x000008300000 : "rootfs1" 0x000008300000-0x000009200000 : "kernel2" 0x000009200000-0x000010000000 : "rootfs2" m25p80 spi0.0: unrecognized JEDEC id ffffff SoC: model = 0x6810, revision = 0x4 o 3 Giga ports supported o SKB recycle supported for SWF (Disabled) o NETA acceleration mode 1 o RX Queue support: 8 Queues * 256 Descriptors o TX Queue support: 8 Queues * 532 Descriptors o GSO supported o GRO supported o Receive checksum offload supported o Transmit checksum offload supported o Driver ERROR statistics enabled o Driver INFO statistics enabled o Driver DEBUG statistics enabled port #0: is_sgmii=0, is_rgmii=1, phy_addr=1 o Loading network interface(s) for port #0: cpu_mask=0x1, tx_csum_limit=9800 o Port 0 is connected to Linux netdevice o eth0, ifindex = 2, GbE port = 0 giga p=0: mtu=1500, mac=00:50:43:02:02:01 (platform) libphy: orion_mdio_bus: probed e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI e1000: Copyright (c) 1999-2006 Intel Corporation. e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k e1000e: Copyright(c) 1999 - 2013 Intel Corporation. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-orion: EHCI orion driver orion-ehci f1058000.usb: EHCI Host Controller orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 orion-ehci f1058000.usb: irq 50, io mem 0xf1058000 orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 3.10.39 ehci_hcd usb usb1: SerialNumber: f1058000.usb hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000 usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: xHCI Host Controller usb usb2: Manufacturer: Linux 3.10.39 xhci-hcd usb usb2: SerialNumber: f10f0000.usb3 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: xHCI Host Controller usb usb3: Manufacturer: Linux 3.10.39 xhci-hcd usb usb3: SerialNumber: f10f0000.usb3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000 usb usb4: New USB device found, idVendor=1d6b, idProduct=0002 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: xHCI Host Controller usb usb4: Manufacturer: Linux 3.10.39 xhci-hcd usb usb4: SerialNumber: f10f8000.usb3 ata2: SATA link down (SStatus 0 SControl 300) hub 4-0:1.0: USB hub found hub 4-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 usb usb5: New USB device found, idVendor=1d6b, idProduct=0003 usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb5: Product: xHCI Host Controller usb usb5: Manufacturer: Linux 3.10.39 xhci-hcd usb usb5: SerialNumber: f10f8000.usb3 hub 5-0:1.0: USB hub found hub 5-0:1.0: 1 port detected usbcore: registered new interface driver usblp usbcore: registered new interface driver usb-storage mousedev: PS/2 mouse device common for all mice mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 i2c /dev entries driver md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com dm_crypt using the OCF package. cpuidle: using governor ladder sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman mmc0: SDHCI controller on f10d8000.sdhci [f10d8000.sdhci] using ADMA sdhci-pltfm: SDHCI platform and OF driver helper armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2 armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: int_coalescing(1) armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources threshold 0x2, threshold_time 0xff mvCesaInit: channels=2, session=640, queue=256 armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode cesadev_init(c0836b3c) usbcore: registered new interface driver usbhid usbhid: USB HID core driver TCP: cubic registered NET: Registered protocol family 10 sit: IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 8021q: 802.1Q VLAN Support v1.8 Key type dns_resolver registered VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 mvebu-rtc f10a3800.rtc: setting system clock to 2017-09-06 11:19:06 UTC (1504696746) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-8: WDC WD10EARS-00Y5B1, 80.00A80, max UDMA/133 ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA WDC WD10EARS-00Y 80.0 PQ: 0 ANSI: 5 ******** sd_probe: turn_off LED_HDD1 ******** ******** sd_probe: turn_on LED_HDD1 WHITE******** sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sd 0:0:0:0: [sda] Attached SCSI disk Freeing unused kernel memory: 6268K (c081d000 - c0e3c000) hotplug1110add:[/devices/soc.0/internal-regs.1/f10a8000.sata/ata1/host0/target0:0:0/0:0:0:0/block/sda][sda]Mass Storage device + ECHO=/bin/echo + RM=/bin/rm + IFCONFIG=/sbin/ifconfig + IP=/bin/ip + MOUNT=/bin/mount + MKDIR=/bin/mkdir + RMDIR=/bin/rmdir + CAT=/bin/cat + MDEV=/sbin/mdev + SETTING_PATH=/etc/settings + [ -f /etc/settings/firmware_info_path ] + cat /etc/settings/firmware_info_path + BASE_PATH=/firmware + BASE_PATH=/firmware + NAND_PATH=/firmware/mnt/nand + DISK_PATH=/firmware/mnt/sysdisk + INFO_PATH=/firmware/mnt/info + MRD_MAC=/firmware/sbin/mrd_mac + INFO_PRINTENV=/firmware/sbin/info_printenv + INFO_SETENV=/firmware/sbin/info_setenv + IMG_PATH=/ram_bin + USB_PATH=/mnt/partnerkey + awk -F= {print $2} + /firmware/sbin/info_printenv curr_bootfrom + CURR_BOOTFROM=2 + awk -F= {print $2} + /firmware/sbin/info_printenv next_bootfrom + NEXT_BOOTFROM=2 + [ 2 != 2 ] + /bin/echo -e \033[031m*** Stage 1: Setup system and device drivers ***\033[0m *** Stage 1: Setup system and device drivers *** + setLED SYS WHITE BLINK Fail to open gpio device + /bin/mount -t proc /proc /proc + /bin/mount -t sysfs /sys /sys + /bin/mount -t usbfs none /proc/bus/usb mount: mount point /proc/bus/usb does not exist + /bin/mount -t devpts devpts /dev/pts + awk {print $1} + grep gpio + cat /proc/devices + mknod -m 644 /dev/gpio c 254 0 + awk -F= {print $2} + /firmware/sbin/info_printenv fwversion_2 + FWVERSION=V5.21(AAZF.1) + awk -F= {print $2} + /firmware/sbin/info_printenv revision_2 + REVISION=50984 + awk -F= {print $2} + /firmware/sbin/info_printenv modelid_2 + MODELID=B303 + awk -F= {print $2} + /firmware/sbin/info_printenv core_checksum_2 + CORE_CHECKSUM=2773b03df8b32c243f8b84dcefa79efb + awk -F= {print $2} + /firmware/sbin/info_printenv zld_checksum_2 + ZLD_CHECKSUM=102d2dc16f397df0dddc4f1ad6380e52 + awk -F= {print $2} + /firmware/sbin/info_printenv romfile_checksum_2 + ROMFILE_CHECKSUM=A762 + awk -F= {print $2} + /firmware/sbin/info_printenv img_checksum_2 + IMG_CHECKSUM=5356a1c083dfd6bc8c74bfd231aa15a6 + [ ! -d /firmware/mnt/info ] + /bin/mkdir -p /firmware/mnt/info + echo V5.21(AAZF.1) + echo 50984 + echo B303 + echo 2773b03df8b32c243f8b84dcefa79efb + echo 102d2dc16f397df0dddc4f1ad6380e52 + echo A762 + echo 5356a1c083dfd6bc8c74bfd231aa15a6 + echo /sbin/mdev + /sbin/mdev -s + /bin/echo 32769 42768 + /bin/echo 8192 + /bin/echo 100 + /bin/echo 5 + /bin/echo 10 + /bin/echo 512 87380 2048000 + /bin/echo 512 65536 2048000 + /bin/echo 524288 + /bin/echo 524288 + /sbin/ifconfig eth0 down + /firmware/sbin/mrd_mac eth0 + /sbin/ifconfig eeth0: mac address changed th0 hw ether 58:8B:F3:DB:DD:3E + /bin/ip link set dev eth0 name egiga0 + /sbin/ifconfig egiga0bmPoolId = 0 has unknown buf_size pool #0: pkt_size=1536, buf_size=1600 - 4096 of 4096 buffers added up egiga0: started IPv6: ADDRCONF(NETDEV_UP): egiga0: link is not ready + /sbin/ifconfig lo add 127.0.0.1 netmask 255.0.0.0 + /sbin/ifconfig lo up + /sbin/ethtool -K egiga0 gso on + /sbin/ethtool -s egiga0 advertise 0x2f Cannot set new settings: Invalid argument + /sbin/ethtool -s egiga0 autoneg on Cannot set new settings: Invalid argument not setting autoneg + /sbin/rtcAccess show + rtc_time1=2017-09-06 11:19:18 + sleep 1 + /sbin/rtcAccess show + rtc_time2=2017-09-06 11:19:19 + [ 2017-09-06 11:19:18 = 2017-09-06 11:19:19 ] + awk -F- {print $1} + echo 2017-09-06 11:19:18 + year1=2017 + awk -F- {print $1} + echo 2017-09-06 11:19:19 + year2=2017 + awk -F- {print $1} + /sbin/rtcAccess show + year3=2017 + [ 2017 != 2017 ] + /sbin/rtcAccess rtctosys + echo 2 + echo 80 + /linuxrc + . /etc/profile + SETTING_PATH=/etc/settings + [ -f /etc/settings/firmware_info_path ] + cat /etc/settings/firmware_info_path + BASE_PATH=/firmware + PATH=/bin:/sbin:/usr/bin:/usr/sbin:/usr/local/bin:/usr/local/sbin:/firmware/sbin:/usr/local/zy-pkgs/bin:/firmware/htp + export PATH + LD_LIBRARY_PATH=/lib:/usr/lib:/usr/lib/private + export LD_LIBRARY_PATH + ECHO=/bin/echo + CAT=/bin/cat + RM=/bin/rm + MOUNT=/bin/mount + UMOUNT=/bin/umount + IP=/bin/ip + IFCONFIG=/sbin/ifconfig + SED=/bin/sed + MKDIR=/bin/mkdir + RMDIR=/bin/rmdir + AWK=/bin/awk + MD5SUM=/sbin/md5sum + REBOOT=/sbin/reboot + BUZZERC=/sbin/buzzerc + LN=/bin/ln + INSMOD=/sbin/insmod + RMMOD=/sbin/rmmod + LSMOD=/sbin/lsmod + DEPMOD=/sbin/depmod + NAND_PATH=/firmware/mnt/nand + DISK_PATH=/firmware/mnt/sysdisk + INFO_PATH=/firmware/mnt/info + HTP_PATH=/firmware/htp + IMG_PATH=/ram_bin + USB_PATH=/mnt/partnerkey + [ -f /etc/settings/config_on_nand_path ] + cat /etc/settings/config_on_nand_path + CONF_PATH=/etc/zyxel + CONFIG_MTD_NUM=2 + CONFIG_MTD=/dev/mtd2 + CONFIG_MTD_BLOCK=/dev/mtdblock2 + GET_MAC_MCU=/sbin/get_mac_mcu.sh + WRITE_MAC_MCU=/sbin/write_mac_mcu.sh + INFO_PRINTENV=/firmware/sbin/info_printenv + INFO_SETENV=/firmware/sbin/info_setenv + MRD_MAC=/firmware/sbin/mrd_mac + MRD_MODEL=/firmware/sbin/mrd_model + NAND_FS_TYPE=ubifs + awk -F= {print $2} + /firmware/sbin/info_printenv curr_bootfrom + CURR_BOOTFROM=2 + [ 2 = 1 ] + IMG_MTD=6 + NEW_ROOT= + SYSINIT_PASSWD=$1$$4eHwTd8s1.UjO3wA36fmX1 + SYSINIT_PATH=/mnt/sysinit + /firmware/sbin/mrd_model -p + MODEL_ID=B303 + RAM_BOOT_ABLE=YES + echo 1 + rescan_lost_scsi_device + wc -l + ls /sys/class/scsi_host + hostNum=2 + cut -c 5 + ls /sys/class/scsi_host + hostIdLst=0 1 + hddId=2 + cat /proc/hdd2_detect cat: can't open '/proc/hdd2_detect': No such file or directory + [ == 1 ] + hddId=1 + cat /proc/hdd1_detect cat: can't open '/proc/hdd1_detect': No such file or directory + [ == 1 ] + /bin/echo -e \033[031m*** Stage 2: Prepare the root file system ***\033[0m *** Stage 2: Prepare the root file system *** + /bin/echo -e \033[033mMount system partition...\033[0m Mount system partition... + /bin/mkdir -p /firmware/mnt/nand + ls -l /dev/ubi_ctrl crw-rw---- 1 root root 10, 59 Sep 6 11:19 /dev/ubi_ctrl + [ ! -e /dev/ubi_ctrl ] + check_and_run_usbkey + USB_CHECK_FILE=/mnt/pEXT4-fs (sda1): Unrecognized mount option "iocharset=utf8" or missing value artnerkey/nas3xx_check_file + grep sd + ls /sys/block/ + any_usb=sda + /bin/echo sda sda + [ -n sda ] + /bin/mkdir /mnt/partnerkey + /biUBI: attaching mtd6 to ubi6 n/echo checking sda checking sda + grep -c ? + grep ^/dev/sda + fdisk -l /dev/sda + qmark_num=0 + grep ^/dev/sda + fdisk -l /dev/sda + partition_num=/dev/sda1 * 2048 1953523711 1953521664 931.5G 83 Linux + [ 0 == 4 ] + [ /dev/sda1 * 2048 1953523711 1953521664 931.5G 83 Linux == ] + sed -n 1p + awk {print $1} + grep ^/dev/sda + fdisk -l /dev/sda + mnt_point=/dev/sda1 + /bin/echo Trying to mount /dev/sda1 Trying to mount /dev/sda1 + /bin/mount -o iocharset=utf8,shortname=mixed /dev/sda1 /mnt/partnerkey mount: wrong fs type, bad option, bad superblock on /dev/sda1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so. + grep /mnt/partnerkey + /bin/cat /proc/mounts + mount_SUC= + [ != ] + /bin/echo Fail to mount /dev/sda1 Fail to mount /dev/sda1 + /bin/rmdir /mnt/partnerkey + ls -l /dev/ubi_ctrl crw-rw---- 1 root root 10, 59 Sep 6 11:19 /dev/ubi_ctrl + ubidetach -d 0 ubidetach: error!: cannot remove ubi0 error 22 (Invalid argument) + ubiattach -m 6 -d 6 UBI: scanning is finished UBI: attached mtd6 (name "rootfs2", size 110 MiB) to ubi6 UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 UBI: good PEBs: 872, bad PEBs: 8, corrupted PEBs: 0 UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 UBI: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 3452188652 UBI: available PEBs: 32, total reserved PEBs: 840, PEBs reserved for bad PEB handling: 32 UBI: background thread "ubi_bgt6d" started, PID 1337 UBI device number 6, total 872 LEBs (110723072 bytes, 105.6 MiB), available 32 LEBs (4063232 bytes, 3.9 MiB), LEB size 126976 bytes (124.0 KiB) + ls -l /dev/ubi6 /dev/ubi6_0 /dev/ubi_ctrl crw-rw---- 1 root root 249, 0 Sep 6 11:19 /dev/ubi6 crw-rw---- 1 root root 249, 1 Sep 6 11:19 /dev/ubi6_0 crw-rw---- 1 root root 10, 59 Sep 6 11:19 /dev/ubi_ctrl + [ ! -e /dev/ubi6 ] + ls -l /dev/ubi6 /dev/ubi6_0 /dev/ubi_ctrl crw-rw---- 1 root root 249, 0 Sep 6 11:19 /dev/ubi6 crw-rw---- 1 root root 249, 1 Sep 6 11:19 UBIFS: mounted UBI device 6, volume 0, name "ubi_rootfs2", R/O mode /dev/ubi6_0 crwUBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes -rw---- 1 rooUBIFS: FS size: 100691968 bytes (96 MiB, 793 LEBs), journal size 5079040 bytes (4 MiB, 40 LEBs) t root UBIFS: reserved for root: 4755930 bytes (4644 KiB) 10, 59 Sep 6 UBIFS: media format: w4/r0 (latest is w4/r0), UUID BC7D1F8A-CB46-4006-85B8-29548DDE9947, small LPT model 11:19 /dev/ubi_ctrl + mount -t ubifs -o ro ubi6:ubi_rootfs2 /firmware/mnt/nand + [ ! -e /firmware/mnt/nand/sysdisk.img.gz ] + cat /proc/htp_pin cat: can't open '/proc/htp_pin': No such file or directory + HTP_PIN= + [ == 1 ] sh: 1: unknown operand + /bin/storage_asm_mntfw_swap.sh /firmware/mnt/sysdisk can not found fw raid uuid can not found swap raid uuid /sbin/mdadm --grow /dev/md0 --raid-devices=2 --force mdadm: /dev/md0 is not an active md array - aborting /sbin/mdadm --grow /dev/md1 --raid-devices=2 --force mdadm: /dev/md1 is not an active md array - aborting storage_asm_mntfw_swap.sh can not swap on /dev/md1 + Flag_HD_Exists=1 + echo 1 1 + [ 1 == 0 ] + echo WARNING: No valid partition on HDD or no HDD plugged! WARNING: No valid partition on HDD or no HDD plugged! + [ YES == YES ] + BOOTDEV=RAM + export BOOTDEV + [ RAM == RAM ] + echo WARNING: No valid partition on HDD or no HDD plugged WARNING: No valid partition on HDD or no HDD plugged + echo Boot from RAM disk Boot from RAM disk + /bin/mkdir -p /firmware/mnt/sysdisk + /bin/mount -t ramfs none /firmware/mnt/sysdisk + gzip -cd /firmware/mnt/nand/sysdisk.img.gz + [ 0 -ne 0 ] + grep change_boot_part + /firmware/sbin/info_printenv + IS_CHANGE_BOOT_PART_EXIST=change_boot_part=0 + [ change_boot_part=0 != ] + awk -F= {print $2} + /firmware/sbin/info_printenv change_boot_part + CHANGE_BOOT_PART=0 + [ 0 == 1 ] + /bin/mount -o remount,ro /firmware/mnt/sysdisk + [ -e /firmware/mnt/sysdiskEXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem /mount.sda1.rw.fEXT4-fs (loop0): mounted filesystem without journal. Opts: (null) lag ] + [ -f /firmware/mnt/sysdisk/sysdisk.img ] + echo -e \033[033mMount system disk image ...\033[0m Mount system disk image ... + /bin/mkdir -p /ram_bin + /bin/mount -t ext2 -o loop,ro /firmware/mnt/sysdisk/sysdisk.img /ram_bin + [ 0 -ne 0 ] + /bin/mount --bind /ram_bin/usr /usr + /bin/mount --bind /ram_bin/lib/security /lib/security + /bin/mount --bind /ram_bin/lib/modules /lib/modules + /bin/mount --bind /ram_bin/lib/locale /lib/locale + cp -a /ram_bin/bin/lld2d /ram_bin/bin/sg_mapUBI: attaching mtd2 to ubi2 /bin/ + cp -a /ram_bin/sbin/DAV_httpd /ram_bin/sbin/controlSSHUBI: scanning is finished .sh /ram_bin/sbin/dosfsck /ram_bin/sbin/exfatfscUBI warning: print_rsvd_warning: cannot reserve enough PEBs for bad PEB handling, reserved 12, need 40 k /ram_bin/sbin/fsck.fat /ram_biUBI: attached mtd2 (name "config", size 2 MiB) to ubi2 n/sbin/fsck.hfs UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes /ram_bin/sbin/ipUBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 notify /ram_bin/UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 sbin/ipnotify_exUBI: good PEBs: 16, bad PEBs: 0, corrupted PEBs: 0 ec.sh /ram_bin/sUBI: user volume: 0, internal volumes: 1, max. volumes count: 128 bin/makekey /ramUBI: max/mean erase counter: 1/1, WL threshold: 4096, image sequence number: 2612544605 _bin/sbin/makepwUBI: available PEBs: 0, total reserved PEBs: 16, PEBs reserved for bad PEB handling: 12 d /ram_bin/sbin/UBI: background thread "ubi_bgt2d" started, PID 1435 mdir /ram_bin/sbin/mkdosfs /ram_bin/sbin/mkexfatfs /ram_bin/sbinUBIFS error (pid 1437): ubifs_mount: cannot open "ubi2:ubi_config", error -19 /mkfs.fat /ram_bin/sbin/monitord /ram_bin/sbin/mount.exfat-fuse /ram_bin/sbin/mount.fuse /ram_bin/sbin/mtools /ram_bin/sbin/sftp-server /ram_bin/sbin/ssh /ram_bin/sbin/ssh-keygUBI: detaching mtd2 from ubi2 en /ram_bin/sbinUBI: mtd2 is detached from ubi2 /sshd /ram_bin/sbin/target.init /ram_bin/sbin/targetcli /ram_bin/sbin/targetcli-ng /ram_bin/sbin/usbzync /ram_bin/sbin/usbzync.sh /ram_bin/sbin/usbzync_rm_rf.sh /sbin/ + /bin/mkdir /tmp/tmpfs + /bin/mount -t tmpfs /dev/ram0 /tmp/tmpfs -o size=5m + /bin/mkdir /tmp/tmpfs/usr_etc + /bin/cp -a /usr/local/etc/mt-daapd /usr/local/etc/mt-daapd.conf /tmp/tmpfs/usr_etc + /bin/mount --bind /tmp/tmpfs/usr_etc /usr/local/etc + /bin/mkdir /tmp/tmpfs/usr_var + /bin/mount --bind /tmp/tmpfs/usr_var /usr/local/var mount: mount point /usr/local/var does not exist + /bin/mkdir -p /tmp/zyxel + cp -a /etc/zyxel/BackupPlanner /etc/zyxel/conf /etc/zyxel/dservice.disable /etc/zyxel/hd-idle.conf /etc/zyxel/pkg_conf /etc/zyxel/storage /etc/zyxel/webdav /etc/zyxel/zyfw /tmp/zyxel + ubiattach -m 2 -d 2 UBI device number 2, total 16 LEBs (2031616 bytes, 1.9 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) + ls -l /dev/ubi2 /dev/ubi6 /dev/ubi6_0 /dev/ubi_ctrl crw-rw---- 1 root root 248, 0 Sep 6 11:19 /dev/ubi2 crw-rw---- 1 root root 249, 0 Sep 6 11:19 /dev/ubi6 crw-rw---- 1 root root 249, 1 Sep 6 11:19 /dev/ubi6_0 crw-rw---- 1 root root 10, 59 Sep 6 11:19 /dev/ubi_ctrl + [ ! -e /dev/ubi2 ] + /bin/mount -t ubifs ubi2:ubi_config /etc/zyxel mount: unknown filesystem type 'ubifs' + [ 32 != 0 ] + /bin/echo mount /etc/zyxel failed mount /etc/zyxel failed + prepare_config_partition + [ /etc/zyxel != ] + echo --- remove all files in /etc/zyxel --- remove all files in /etc/zyxel + rm -rf /etc/zyxel/BackupPlanner /etc/zyxel/conf /etc/zyxel/dservice.disable /etc/zyxel/hd-idle.conf /etc/zyxel/pkg_conf /etc/zyxel/storage /etc/zyxel/webdav /etc/zyxel/zyfw + echo --- umount /etc/zyxel --- umount /etc/zyxel + umount /etc/zyxel umount: /etc/zyxel: not mounted + echo --- remove "ubi_config" volume --- remove "ubi_config" volume + ubirmvol /dev/ubi2 -N ubi_config ubirmvol: error!: cannot find UBI volume "ubi_config" error 2 (No such file or directory) + echo --- detach ubi2 from /dev/mtd2 --- detach ubi2 from /dev/mtd2 + ubidetach -m 2 + sleep 1 + [ 0 == 0 ] + echo --- flash_erase /dev/mtd2 0 0 --- flash_erase /dev/mtd2 0 0 + flash_erase /dev/mtd2 0 0 ErasUBI: attaching mtd2 to ubi2complete ing 128 Kibyte @ 20000 -- 6 % cUBI: scanning is finished ErasingUBI: empty MTD device detected Erasing 128 Kibyte @ a0000 -- 31UBI warning: print_rsvd_warning: cannot reserve enough PEBs for bad PEB handling, reserved 12, need 40 Erasing 128 Kibyte UBI: attached mtd2 (name "config", size 2 MiB) to ubi2 @ c0000 -- 37 % UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ErasinUBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 g 128 Kibyte @ eUBI: VID header offset: 2048 (aligned 2048), data offset: 4096 0000 -- 43 % comUBI: good PEBs: 16, bad PEBs: 0, corrupted PEBs: 0 Erasing 1UBI: user volume: 0, internal volumes: 1, max. volumes count: 128 28 Kibyte @ 1000UBI: max/mean erase counter: 0/0, WL threshold: 4096, image sequence number: 1414135477 00 -- 50 % complUBI: available PEBs: 0, total reserved PEBs: 16, PEBs reserved for bad PEB handling: 12 Erasing 128UBI: background thread "ubi_bgt2d" started, PID 1454 Erasing 128 Kibyte @ 140000 -UBIFS error (pid 1456): ubifs_mount: cannot open "ubi2:ubi_config", error -19 Erasing 128 Kibyte @ 1e0000 -- 100 % complete + echo --- mount /etc/zyxel back --- mount /etc/zyxel back + ubiattach -m 2 -d 2 UBI device number 2, total 16 LEBs (2031616 bytes, 1.9 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) + ubimkvol /dev/ubi2 -N ubi_config -m ubimkvol: error!: UBI device does not have free logical eraseblocks + /bin/mount -t ubifs ubi2:ubi_config /etc/zyxel mount: unknown filesystem type 'ubifs' + /bin/cp -af /tmp/NTFS driver 2.1.30 [Flags: R/O MODULE]. zyxel /etc/ + rm -rf /tmp/zyxel + [ -f /etc/zyxel/zyconf.tgz ]tntfs: module license 'Commercial. For support email ntfs-support@tuxera.com.' taints kernel. + /bin/chmod 7Disabling lock debugging due to kernel taint 77 /etc/zyxel + /ram_bin/etc/inTuxera NTFS driver 3015.1.29 [Flags: R/W MODULE]. it.d/rcS2 Start rcS2 of ZyXEL style *** Stage 3: Start services on HDD *** PPP generic driver version 2.4.2 PPP MPPE Compression module registered PPP Deflate Compression module registered NET: Registered protocol family 24 PPP BSD Compression module registered HTP finished, reUBI error: ubi_attach_mtd_dev: mtd2 is already attached to ubi2 -mount /etc/zyxel ubiattach: erUBIFS error (pid 1499): ubifs_mount: cannot open "ubi2:ubi_config", error -19 ror!: cannot attach mtd2 error 17 (File exists) mount: unknown filesystem type 'ubifs' Press ENTER to continue... Starting zylogd... zylog starts. Starting uamd... Starting WSGI server... CherryPy Checker: The Application mounted at '' has an empty config. [06/Sep/2017:11:19:35] [network_common.py.pre](check_link_status)(278): the interface bond0 is down or unusable [06/Sep/2017:11:19:37] [network_common.py.pre](check_link_status)(278): the interface bond0 is down or unusable [06/Sep/2017:11:19:37] [network_main_model_back.py.pre](ipv6_dhcp_static_setting_apply)(229): The interface bond0 is down! [06/Sep/2017:11:19:37] [network_common.py.pre](check_link_status)(278): the interface egiga1 is down or unusable [06/Sep/2017:11:19:40] [network_common.py.pre](check_link_status)(278): the interface egiga1 is down or unusable [06/Sep/2017:11:19:40] [network_main_model_back.py.pre](ipv6_dhcp_static_setting_apply)(229): The interface egiga1 is down! [06/Sep/2017:11:19:42] [network_main_model_back.py.pre](ipv6_dhcp_static_setting_apply)(229): The interface egiga0 is down! [06/Sep/2017:11:19:43] [network_main_model_front.py.pre](apache_config_setting)(627): There is no statement '#WebService Start#' in httpd_zld.conf. keep going... killall: pure-ftpd: no process killed no printer device detected. Usage: umount [-hV] umount -a [options] umount [options] <source> | <directory> Options: -a, --all unmount all filesystems -A, --all-targets unmount all mountpoints for the given device in the current namespace -c, --no-canonicalize don't canonicalize paths -d, --detach-loop if mounted loop device, also free this loop device --fake dry run; skip the umount(2) syscall -f, --force force unmount (in case of an unreachable NFS system) -i, --internal-only don't call the umount.<type> helpers -n, --no-mtab don't write to /etc/mtab -l, --lazy detach the filesystem now, clean up things later -O, --test-opts <list> limit the set of filesystems (use with -a) -R, --recursive recursively unmount a target with all its children -r, --read-only in case unmounting fails, try to remount read-only -t, --types <list> limit the set of filesystem types -v, --verbose say what is being done -h, --help display this help and exit -V, --version output version information and exit For more details see umount(8). Usage: umount [-hV] umount -a [options] umount [options] <source> | <directory> Options: -a, --all unmount all filesystems -A, --all-targets unmount all mountpoints for the given device in the current namespace -c, --no-canonicalize don't canonicalize paths -d, --detach-loop if mounted loop device, also free this loop device --fake dry run; skip the umount(2) syscall -f, --force force unmount (in case of an unreachable NFS system) -i, --internal-only don't call the umount.<type> helpers -n, --no-mtab don't write to /etc/mtab -l, --lazy detach the filesystem now, clean up things later -O, --test-opts <list> limit the set of filesystems (use with -a) -R, --recursive recursively unmount a target with all its children -r, --read-only in case unmounting fails, try to remount read-only -t, --types <list> limit the set of filesystem types -v, --verbose say what is being done -h, --help display this help and exit -V, --version output version information and exit For more details see umount(8). BusyBox v1.19.4 (2017-05-26 16:39:12 CST) multi-call binary. Usage: rmdir [OPTIONS] DIRECTORY... No more ZySH daemon and client... argv[0]=/usr/sbin/zylog_config argv[1]=mail argv[2]=1 argv[3]=subject argv[4]=NAS326 Log Report mail server'1' subject:NAS326 Log Report argv[0]=/usr/sbin/zylog_config argv[1]=mail argv[2]=1 argv[3]=schedule argv[4]=hourly mail server '1' schedule is : hourly Starting "/etc/init.d/zypkg_controller.sh". Starting to set up zy-pkgs environment ... -> No volume exists now. zy-pkgs will not work. Starting smbd... Starting nmbd... Starting NSU Agent... Starting AFP... avahi-daemon netatalk. There is no usable system volume! Do nothing... GMT offset=28800s setting system time zone to tz_minuteswest=-480 killall: hd-idle: no process killed schedule_controller is already running now. setLED COPY OFF led_state_map_addr = 400 setLED USB OFF led_state_map_addr = 300 Starting app_wd... Update zypkg list There is no sysvol "/i-data/.system" ===> Generate zysync server config ... ===> Generating volume list ... ===> Generating zysync config file ... rm: can't remove '/tmp/zysync_modules': No such file or directory ===> Starting zysync server ... [INFO]: Starting server mode ... Done ===> Generating stunnel server config file ... ===> Starting stunnel server ... [.] stunnel 5.02 on arm-unknown-linux-gnu platform [.] Compiled/running with OpenSSL 1.0.2h 3 May 2016 [.] Threading:FORK Sockets:POLL,IPv6 SSL:FIPS [ ] errno: (*__errno_location ()) [.] Reading configuration from file /etc/stunneld.conf [.] FIPS mode disabled [ ] Compression disabled [ ] Snagged 64 random bytes from //.rnd [ ] Wrote 1024 new random bytes to //.rnd [ ] PRNG seeded successfully [ ] Initializing service [szysync] [ ] Loading cert from file: /etc/zyxel/BackupPlanner/zysync/zysync.cert [ ] Loading key from file: /etc/zyxel/BackupPlanner/zysync/zysync.key [:] Insecure file permissions on /etc/zyxel/BackupPlanner/zysync/zysync.key [ ] Private key check succeeded [ ] DH initialization [ ] Could not load DH parameters from /etc/zyxel/BackupPlanner/zysync/zysync.cert [ ] Using hardcoded DH parameters [ ] DH initialized with 2048-bit key [ ] ECDH initialization [ ] ECDH initialized with curve prime256v1 [ ] SSL options set: 0x01000004 [.] Configuration successful [ ] Service [szysync] (FD=6) bound to 0.0.0.0:9527 [!] Cannot open log file: /i-data/.system/stunneld.log [ ] Closing service [szysync] [ ] Service [szysync] closed (FD=6) [ ] Sessions cached before flush: 0 [ ] Sessions cached after flush: 0 [ ] Service [szysync] closed Done [ ok ] The Linux SCSI Target is already stopped [warn] Creating missing directory /var/target/pr ... (warning). [warn] Creating missing directory /var/target/alua ... (warning). [info] The Linux SCSI Target looks properly installed. [warn] The configfs filesystem was not mounted, consider adding it to fstab ... (warning). Rounding down aligned max_sectors from 4294967295 to 4294967288 [info] Loaded core module target_core_file. [warn] Core module target_core_mod already loaded ... (warning). [info] Loaded fabric module iscsi_target_mod. [warn] Startup config /etc/target/scsi_target.lio is empty, skipping ... (warning). [ ok ] Started The Linux SCSI Target 2017/09/06 19:19:55 [ipnotify] : execute ipnotify STARTUP [ipnotify_exec.sh]: ******** run ipnotify_exec.sh STARTUP******** [06/Sep/2017:19:19:55] [network_common.py.pre](check_link_status)(278): the interface bond0 is down or unusable [06/Sep/2017:19:19:55] [network_common.py.pre](check_link_status)(278): the interface bond1 is down or unusable [06/Sep/2017:19:19:55] [network_common.py.pre](check_link_status)(278): the interface egiga1 is down or unusable the interface egiga0 is down or unusable [06/Sep/2017:19:19:55] [network_common.py.pre](check_link_status)(278): the interface bond0 is down or unusable [06/Sep/2017:19:19:55] [network_common.py.pre](check_link_status)(278): the interface bond1 is down or unusable [06/Sep/2017:19:19:55] [network_common.py.pre](check_link_status)(278): the interface egiga1 is down or unusable [06/Sep/2017:19:19:56] [network_common.py.pre](check_link_status)(278): the interface bond0 is down or unusable [06/Sep/2017:19:19:56] [network_common.py.pre](check_link_status)(278): the interface bond1 is down or unusable [06/Sep/2017:19:19:56] [network_common.py.pre](check_link_status)(278): the interface egiga1 is down or unusable Device "egiga1" does not exist. killall: httpd: no process killed killall: httpd: no process killed ---------------------------------------------- admin /i-data/sysvol/admin doesn't exist. Skip it. ---------------------------------------------- music /i-data/sysvol/music doesn't exist. Skip it. ---------------------------------------------- photo /i-data/sysvol/photo doesn't exist. Skip it. ---------------------------------------------- video /i-data/sysvol/video doesn't exist. Skip it. ===> Stopping crond ... ===> Starting crond ... httpd[3007]: [warn] Init: Session Cache is not configured [hint: SSLSessionCache] httpd[3007]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?) httpd[3007]: [warn] RSA server certificate CommonName (CN) `NAS326' does NOT match server name!? httpd[3007]: [error] mod_auth_zyxel: initialized. core_checksum : 2773b03df8b32c243f8b84dcefa79efb fwversion : V5.21(AAZF.1) img_checksum : 5356a1c083dfd6bc8c74bfd231aa15a6 modelid : B303 revision : 50984 romfile_checksum : A762 zld_checksum : 102d2dc16f397df0dddc4f1ad6380e52 OK led_state_map_addr = 6 Please press Enter to activate this console. httpd[3023]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?) httpd[3023]: [warn] RSA server certificate CommonName (CN) `NAS326' does NOT match server name!? httpd[3023]: [error] mod_auth_zyxel: initialized.
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's September 05, 2017 11:52PM |
Admin Registered: 13 years ago Posts: 18,575 |
setenv curr_bootfrom 1 setenv next_bootfrom 1 printenv boot
Quote
> Linux version 3.10.39 (root@SDD2SVR2) (gcc version
> 4.8.5 20150209 (prerelease) (crosstool-NG 1.21.0)
> ) #1 Fri May 26 16:47:54 CST 2017
> CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7)
> , cr=10c53c7d
> CPU: PIPT / VIPT nonaliasing data cache, VIPT alia
> sing instruction cache
> Machine: Marvell Armada 380/381/382/385/388 (Devic
> e Tree), model: Marvell Armada 380 STG-328
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's September 08, 2017 03:13PM |
Registered: 6 years ago Posts: 23 |
Sending debug message. Please reboot the target.../ [Type Ctrl-\ + c to quit] M - 1.73 Booting from NAND flash General initialization - Version: 1.0.0 Detected Device ID 6810 High speed PHY - Version: 2.0 Init RD NAS topology board SerDes lanes topology details: | Lane # | Speed | Type | -------------------------------- | 0 | 06 | SATA0 | | 1 | 05 | USB3 HOST0 | | 2 | 06 | SATA1 | | 5 | 05 | USB3 HOST1 | -------------------------------- High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.26.0 mvSysEnvGetTopologyUpdateInfo: TWSI Read failed DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully Not detected suspend to RAM indication BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01-svn48023 (Oct 13 2015 - 09:25:56) Marvell version: 2014_T3.0p6 Board: RD-NAS-88F6820-DDR3 SoC: MV88F6810 Rev A0 running 1 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 250 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB Map: Code: 0x1fed0000:0x1ff95d60 BSS: 0x1ffef2b4 Stack: 0x1f9cff20 Heap: 0x1f9d0000:0x1fed0000 U-Boot Environment: 0x00200000:0x00280000 (NAND) NAND: 256 MiB MMC: mv_sdh: 0 *** Booting kernel from kernel 2 @0x08700000 *** USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | 0x01 | egiga0 [PRIME] Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x8700000, size 0xf00000 15728640 bytes read: OK * kernel: cmdline image address = 0x02000000 Starting kernel ... Power on HDD1 ... Power on HDD2 ... Power on USB ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 3.10.39 (root@SDD2SVR2) (gcc version 4.8.5 20150209 (prerelease) (crosstool-NG 1.21.0) ) #1 Fri May 26 16:47:54 CST 2017 CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: Marvell Armada 380/381/382/385/388 (Device Tree), model: Marvell Armada 380 STG-328 bootconsole [earlycon0] enabled Memory policy: ECC disabled, Data cache writealloc CPU: All CPU(s) started in SVC mode. Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=armada-nand:2m(u-boot),2m(env),2m(config),15m(kernel1),110m(rootfs1),15m(kernel2),-(rootfs2) earlyprintk=serial PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 512MB = 512MB total Memory: 504456k/504456k available, 19832k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xe0800000 - 0xfff00000 ( 503 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc081c8a8 (8275 kB) .init : 0xc081d000 - 0xc0e3cd5c (6272 kB) .data : 0xc0e3e000 - 0xc0e950e0 ( 349 kB) .bss : 0xc0e950e0 - 0xc0ee2c70 ( 311 kB) NR_IRQS:16 nr_irqs:16 16 LSP version: linux-3.10.39-2014_T3.0p7
Sending debug message. Please reboot the target.../ [Type Ctrl-\ + c to quit] M - 1.73 Booting from NAND flash General initialization - Version: 1.0.0 Detected Device ID 6810 High speed PHY - Version: 2.0 Init RD NAS topology board SerDes lanes topology details: | Lane # | Speed | Type | -------------------------------- | 0 | 06 | SATA0 | | 1 | 05 | USB3 HOST0 | | 2 | 06 | SATA1 | | 5 | 05 | USB3 HOST1 | -------------------------------- High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.26.0 mvSysEnvGetTopologyUpdateInfo: TWSI Read failed DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully Not detected suspend to RAM indication BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01-svn48023 (Oct 13 2015 - 09:25:56) Marvell version: 2014_T3.0p6 Board: RD-NAS-88F6820-DDR3 SoC: MV88F6810 Rev A0 running 1 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 250 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB Map: Code: 0x1fed0000:0x1ff95d60 BSS: 0x1ffef2b4 Stack: 0x1f9cff20 Heap: 0x1f9d0000:0x1fed0000 U-Boot Environment: 0x00200000:0x00280000 (NAND) NAND: 256 MiB MMC: mv_sdh: 0 *** Booting kernel from kernel 2 @0x08700000 *** USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | 0x01 | egiga0 [PRIME] Hit any key to stop autoboot: 0 Marvell>> printenv CASset=max CONTRY_TYPE=FF FEATURE_BIT=00 MALLOC_len=5 MODEL_ID=B303 MPmode=SMP PRODUCT_NAME=STG-328 VENDOR_NAME=MitraStar Technology Corp. autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=armada-nand:2m(u-boot),2m(env),2m(config),15m(kernel1),110m(rootfs1),15m(kernel2),-(rootfs2) earlyprintk=serial bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=nand read 0x2000000 0x08700000 0xF00000 && bootz 0x2000000 bootcmd_auto=stage_boot $boot_order bootcmd_custom=if run bootcmd_exec; then; else if run bootcmd_stock_1; then; else run bootcmd_stock_2; reset; fi; fi bootcmd_custom_sata=if run sata_bootcmd; then; else if run bootcmd_stock_1; then; else run bootcmd_stock_2; reset; fi; fi bootcmd_exec=run scan_disk; echo Booting from $bootdev $device ...; setenv fdt_skip_update yes; if run load_image; then if run load_dtb; then if run load_initrd; then run set_bootargs; bootz $load_image_addr $load_initrd_addr $load_dtb_addr; fi; fi; fi bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootcmd_stock_1=run set_bootargs_stock; echo Booting from NAND kernel 1 ...; nand read 0x2000000 0x00E00000 0xF00000 && bootz 0x2000000 bootcmd_stock_2=run set_bootargs_stock; echo Booting from NAND kernel 2 ...; nand read 0x2000000 0x08700000 0xF00000 && bootz 0x2000000 bootdelay=3 cacheShare=no change_boot_part=0 console=console=ttyS0,115200 core_checksum_1=e9b3248e8c69ec9ef52a8698d0835aae core_checksum_2=2773b03df8b32c243f8b84dcefa79efb curr_bootfrom=2 device_partition=0:1 devices=usb scsi disaMvPnp=no disks=0 1 2 3 dtb_file=/boot/dts/armada-380-zyxel-nas326.dtb eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:38:32:25 eth1mtu=1500 eth2addr=00:50:43:38:a6:25 eth2mtu=1500 eth3addr=00:50:43:32:a6:38 eth3mtu=1500 ethact=egiga0 ethaddr=58:8B:F3:DB:DD:3E ethmtu=1500 ethprime=egiga0 fdt_addr=2040000 fdt_skip_update=yes fdtaddr=0x1000000 fdtfile=armada-38x-modular.dtb filesize=0x6e8f80 fwversion_1=V5.21(AAZF.0) fwversion_2=V5.21(AAZF.1) ide_path=/ image_name=uImage img_checksum_1=db4be927b09d7ea9a1284d2e6f330db5 img_checksum_2=5356a1c083dfd6bc8c74bfd231aa15a6 initrd_name=uInitrd ipaddr=10.4.50.170 kernel_addr=${kernel_addr_1} kernel_addr_1=0x00000000; run bootcmd_custom; kernel_addr_2=0x08700000 kernel_addr_r=2080000 kernel_mtd_1=3 kernel_mtd_2=5 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 load_dtb=echo loading DTB $dtb_file ...; ext2load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1000000 load_image=echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/zImage load_image_addr=0x02000000 load_initrd=echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x2900000 loadaddr=0x02000000 loads_echo=0 modelid_1=B303 modelid_2=B303 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:2m(u-boot),2m(env),2m(config),15m(kernel1),110m(rootfs1),15m(kernel2),-(rootfs2) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:25:a6:38 nandEcc=nfcConfig=4bitecc netbsd_en=no netmask=255.255.255.0 netretry=no next_bootfrom=2 pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 revision_1=50967 revision_2=50984 romfile_checksum_1=4EE9 romfile_checksum_2=A762 rootpath=/srv/nfs/ sata_bootcmd=echo Booting from SATA ...; setenv fdt_skip_update yes; run sata_init; ext2load scsi 0:1 $load_image_addr /boot/zImage; ext2load scsi 0:1 $load_dtb_addr /boot/dts/armada-380-zyxel-nas326.dtb; ext2load scsi 0:1 $load_initrd_addr /boot/uInitrd; run sata_set_bootargs; bootz $load_image_addr $load_initrd_addr $load_dtb_addr sata_delay_reset=0 sata_dma_mode=yes sata_init=mw.l f1018100 20420000; mw.l f1018140 003ca800; sleep 3; scsi init sata_set_bootargs=setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial" scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "run usb_init"; setenv scan_scsi "run sata_init"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if ext2load $dev $disknum:1 $load_image_addr /boot/zImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done script_addr_r=3000000 script_name=boot.scr scsidevs=0 serial_number=S150Y46042395 serverip=10.4.50.38 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial set_bootargs_stock=setenv bootargs "console=ttyS0,115200 ubi.mtd=4,2048 rootfstype=ubifs root=ubi0:rootfs1 rw rootdelay=2" standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial sysimg_mtd_1=4 sysimg_mtd_2=6 usb0Mode=host usbActive=0 usbType=2 usb_bootcmd=echo Booting from USB ...; setenv fdt_skip_update yes; run usb_init; ext2load usb 0:1 $load_image_addr /boot/zImage; ext2load usb 0:1 $load_dtb_addr /boot/dts/armada-380-zyxel-nas326.dtb; ext2load usb 0:1 $load_initrd_addr /boot/uInitrd; run usb_set_bootargs; bootz $load_image_addr $load_initrd_addr $load_dtb_addr usb_init=mw.l f1018100 20420000; mw.l f1018140 003E8800; sleep 3; usb start usb_set_bootargs=setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial" vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 zld_checksum_1=b44f1fe16e53092068270b337dee223c zld_checksum_2=102d2dc16f397df0dddc4f1ad6380e52 Environment size: 7079/524284 bytes Marvell>>
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's September 08, 2017 04:10PM |
Admin Registered: 13 years ago Posts: 18,575 |
Hit any key to stop autoboot: 0
Marvell>>
setenv curr_bootfrom 1 setenv next_bootfrom 1 setenv change_boot_part 1
saveenvAnd then print them out
printenv
reset
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's September 09, 2017 08:21AM |
Registered: 6 years ago Posts: 23 |
pi@raspberrypi:~ $ cd Downloads/ pi@raspberrypi:~/Downloads $ sudo ./kwboot -t -B 115200 /dev/ttyUSB0 -d Sending debug message. Please reboot the target...| [Type Ctrl-\ + c to quit] M - 1.73 Booting from NAND flash General initialization - Version: 1.0.0 Detected Device ID 6810 High speed PHY - Version: 2.0 Init RD NAS topology board SerDes lanes topology details: | Lane # | Speed | Type | -------------------------------- | 0 | 06 | SATA0 | | 1 | 05 | USB3 HOST0 | | 2 | 06 | SATA1 | | 5 | 05 | USB3 HOST1 | -------------------------------- High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.26.0 mvSysEnvGetTopologyUpdateInfo: TWSI Read failed DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully Not detected suspend to RAM indication BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01-svn48023 (Oct 13 2015 - 09:25:56) Marvell version: 2014_T3.0p6 Board: RD-NAS-88F6820-DDR3 SoC: MV88F6810 Rev A0 running 1 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 250 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB Map: Code: 0x1fed0000:0x1ff95d60 BSS: 0x1ffef2b4 Stack: 0x1f9cff20 Heap: 0x1f9d0000:0x1fed0000 U-Boot Environment: 0x00200000:0x00280000 (NAND) NAND: 256 MiB MMC: mv_sdh: 0 *** Booting kernel from kernel 2 @0x08700000 *** USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | 0x01 | egiga0 [PRIME] Hit any key to stop autoboot: 0 Marvell>> setenv curr_bootfrom 1 Marvell>> setenv next_bootfrom 1 Marvell>> setenv change_boot_part 1 Marvell>> saveenv Saving Environment to NAND... Erasing Nand... Writing to Nand... done Marvell>> printenv CASset=max CONTRY_TYPE=FF FEATURE_BIT=00 MALLOC_len=5 MODEL_ID=B303 MPmode=SMP PRODUCT_NAME=STG-328 VENDOR_NAME=MitraStar Technology Corp. autoload=no baudrate=115200 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=armada-nand:2m(u-boot),2m(env),2m(config),15m(kernel1),110m(rootfs1),15m(kernel2),-(rootfs2) earlyprintk=serial bootargs_dflt=$console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=nand read 0x2000000 0x08700000 0xF00000 && bootz 0x2000000 bootcmd_auto=stage_boot $boot_order bootcmd_custom=if run bootcmd_exec; then; else if run bootcmd_stock_1; then; else run bootcmd_stock_2; reset; fi; fi bootcmd_custom_sata=if run sata_bootcmd; then; else if run bootcmd_stock_1; then; else run bootcmd_stock_2; reset; fi; fi bootcmd_exec=run scan_disk; echo Booting from $bootdev $device ...; setenv fdt_skip_update yes; if run load_image; then if run load_dtb; then if run load_initrd; then run set_bootargs; bootz $load_image_addr $load_initrd_addr $load_dtb_addr; fi; fi; fi bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name; setenv bootargs $bootargs_dflt; bootm 0x2000000; bootcmd_stock_1=run set_bootargs_stock; echo Booting from NAND kernel 1 ...; nand read 0x2000000 0x00E00000 0xF00000 && bootz 0x2000000 bootcmd_stock_2=run set_bootargs_stock; echo Booting from NAND kernel 2 ...; nand read 0x2000000 0x08700000 0xF00000 && bootz 0x2000000 bootdelay=3 cacheShare=no change_boot_part=1 console=console=ttyS0,115200 core_checksum_1=e9b3248e8c69ec9ef52a8698d0835aae core_checksum_2=2773b03df8b32c243f8b84dcefa79efb curr_bootfrom=1 device_partition=0:1 devices=usb scsi disaMvPnp=no disks=0 1 2 3 dtb_file=/boot/dts/armada-380-zyxel-nas326.dtb eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:38:32:25 eth1mtu=1500 eth2addr=00:50:43:38:a6:25 eth2mtu=1500 eth3addr=00:50:43:32:a6:38 eth3mtu=1500 ethact=egiga0 ethaddr=58:8B:F3:DB:DD:3E ethmtu=1500 ethprime=egiga0 fdt_addr=2040000 fdt_skip_update=yes fdtaddr=0x1000000 fdtfile=armada-38x-modular.dtb filesize=0x6e8f80 fwversion_1=V5.21(AAZF.0) fwversion_2=V5.21(AAZF.1) ide_path=/ image_name=uImage img_checksum_1=db4be927b09d7ea9a1284d2e6f330db5 img_checksum_2=5356a1c083dfd6bc8c74bfd231aa15a6 initrd_name=uInitrd ipaddr=10.4.50.170 kernel_addr=${kernel_addr_1} kernel_addr_1=0x00000000; run bootcmd_custom; kernel_addr_2=0x08700000 kernel_addr_r=2080000 kernel_mtd_1=3 kernel_mtd_2=5 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 load_dtb=echo loading DTB $dtb_file ...; ext2load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1000000 load_image=echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/zImage load_image_addr=0x02000000 load_initrd=echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x2900000 loadaddr=0x02000000 loads_echo=0 modelid_1=B303 modelid_2=B303 mtdids=nand0=armada-nand mtdparts=mtdparts=armada-nand:2m(u-boot),2m(env),2m(config),15m(kernel1),110m(rootfs1),15m(kernel2),-(rootfs2) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:25:a6:38 nandEcc=nfcConfig=4bitecc netbsd_en=no netmask=255.255.255.0 netretry=no next_bootfrom=1 pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 revision_1=50967 revision_2=50984 romfile_checksum_1=4EE9 romfile_checksum_2=A762 rootpath=/srv/nfs/ sata_bootcmd=echo Booting from SATA ...; setenv fdt_skip_update yes; run sata_init; ext2load scsi 0:1 $load_image_addr /boot/zImage; ext2load scsi 0:1 $load_dtb_addr /boot/dts/armada-380-zyxel-nas326.dtb; ext2load scsi 0:1 $load_initrd_addr /boot/uInitrd; run sata_set_bootargs; bootz $load_image_addr $load_initrd_addr $load_dtb_addr sata_delay_reset=0 sata_dma_mode=yes sata_init=mw.l f1018100 20420000; mw.l f1018140 003ca800; sleep 3; scsi init sata_set_bootargs=setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial" scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "run usb_init"; setenv scan_scsi "run sata_init"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if ext2load $dev $disknum:1 $load_image_addr /boot/zImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done script_addr_r=3000000 script_name=boot.scr scsidevs=0 serial_number=S150Y46042395 serverip=10.4.50.38 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial set_bootargs_stock=setenv bootargs "console=ttyS0,115200 ubi.mtd=4,2048 rootfstype=ubifs root=ubi0:rootfs1 rw rootdelay=2" standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial sysimg_mtd_1=4 sysimg_mtd_2=6 usb0Mode=host usbActive=0 usbType=2 usb_bootcmd=echo Booting from USB ...; setenv fdt_skip_update yes; run usb_init; ext2load usb 0:1 $load_image_addr /boot/zImage; ext2load usb 0:1 $load_dtb_addr /boot/dts/armada-380-zyxel-nas326.dtb; ext2load usb 0:1 $load_initrd_addr /boot/uInitrd; run usb_set_bootargs; bootz $load_image_addr $load_initrd_addr $load_dtb_addr usb_init=mw.l f1018100 20420000; mw.l f1018140 003E8800; sleep 3; usb start usb_set_bootargs=setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial" vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 zld_checksum_1=b44f1fe16e53092068270b337dee223c zld_checksum_2=102d2dc16f397df0dddc4f1ad6380e52 Environment size: 7079/524284 bytes Marvell>> reset resetting ... terminal: Input/output error pi@raspberrypi:~/Downloads $ sudo ./kwboot -t -B 115200 /dev/ttyUSB0 -d /dev/ttyUSB0: No such file or directory pi@raspberrypi:~/Downloads $ sudo ./kwboot -t -B 115200 /dev/ttyUSB0 -d /dev/ttyUSB0: No such file or directory pi@raspberrypi:~/Downloads $ sudo ./kwboot -t -B 115200 /dev/ttyUSB0 -d Sending debug message. Please reboot the target.../ [Type Ctrl-\ + c to quit] ound 1 device(s). device scsi 0:1 1 bytes read in 84 ms (0 Bytes/s) Found bootable drive on scsi 0 Booting from scsi 0:1 ... loading Image ... 3904400 bytes read in 109 ms (34.2 MiB/s) loading DTB /boot/dts/armada-380-zyxel-nas326.dtb ... 18234 bytes read in 138 ms (128.9 KiB/s) loading uInitrd ... 6210503 bytes read in 213 ms (27.8 MiB/s) * kernel: cmdline image address = 0x02000000 ## Loading init Ramdisk from Legacy Image at 02900000 ... Image Name: initramfs-4.9.0-mvebu-tld-12 Created: 2017-02-03 23:57:32 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6210439 Bytes = 5.9 MiB Load Address: 00000000 Entry Point: 00000000 ## Flattened Device Tree blob at 01000000 Booting using the fdt blob at 0x01000000 Loading Ramdisk to 1f3e2000, end 1f9ce387 ... OK Loading Device Tree to 00ff8000, end 00fff739 ... OK Skipping Device Tree update ('fdt_skip_update' = yes) Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.0-mvebu-tld-12 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #2 SMP PREEMPT Wed Feb 1 02:31:29 PST 2017 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt:Machine model: Zyxel NAS326 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 15 pages/cpu @dfbd9000 s30796 r8192 d22452 u61440 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=armada-nand:2m(u-boot),2m(env),2m(config),15m(kernel1),110m(rootfs1),15m(kernel2),-(rootfs2) earlyprintk=serial [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 500168K/524288K available (8192K kernel code, 690K rwdata, 2052K rodata, 1024K init, 386K bss, 24120K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0daca28 ( 691 kB) [ 0.000000] .bss : 0xc0daca28 - 0xc0e0d4f8 ( 387 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] mvebu_mbus: [Firmware Warn]: deprecated mbus-mvebu Device Tree, suspend/resume will not work [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 D prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001 [ 0.000000] Switching to timer-based delay loop, resolution 40ns [ 0.000004] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns [ 0.007883] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.019118] Console: colour dummy device 80x30 [ 0.023632] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000) [ 0.034040] pid_max: default: 32768 minimum: 301 [ 0.038800] Security Framework initialized [ 0.042998] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.049672] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.057238] CPU: Testing write buffer coherency: ok [ 0.062319] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.068061] Setting up static identity map for 0x100000 - 0x100058 [ 0.074382] mvebu-soc-id: MVEBU SoC ID=0x6810, Rev=0x4 [ 0.079659] mvebu-pmsu: Initializing Power Management Service Unit [ 0.203631] Brought up 1 CPUs [ 0.206671] SMP: Total of 1 processors activated (50.00 BogoMIPS). [ 0.212906] CPU: All CPU(s) started in SVC mode. [ 0.218072] devtmpfs: initialized [ 0.233696] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.241636] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.251599] prandom: seed boundary self test passed [ 0.258618] prandom: 100 self tests passed [ 0.262779] pinctrl core: initialized pinctrl subsystem [ 0.268789] NET: Registered protocol family 16 [ 0.274082] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.303611] cpuidle: using governor ladder [ 0.333504] cpuidle: using governor menu [ 0.337581] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.345641] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.351645] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling [ 0.359792] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling [ 0.464533] vgaarb: loaded [ 0.467472] SCSI subsystem initialized [ 0.473816] usbcore: registered new interface driver usbfs [ 0.479690] usbcore: registered new interface driver hub [ 0.485173] usbcore: registered new device driver usb [ 0.490639] media: Linux media interface: v0.10 [ 0.495488] Linux video capture interface: v2.00 [ 0.501308] clocksource: Switched to clocksource armada_370_xp_clocksource [ 0.537475] VFS: Disk quotas dquot_6.6.0 [ 0.541574] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.558652] NET: Registered protocol family 2 [ 0.563893] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.571015] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.577580] TCP: Hash tables configured (established 4096 bind 4096) [ 0.584379] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.590278] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.596720] NET: Registered protocol family 1 [ 0.621427] RPC: Registered named UNIX socket transport module. [ 0.627404] RPC: Registered udp transport module. [ 0.632202] RPC: Registered tcp transport module. [ 0.636967] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.643601] Unpacking initramfs... [ 0.889118] Freeing initrd memory: 6068K (df3e2000 - df9cf000) [ 0.895186] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.901948] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.911138] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.917664] audit: initializing netlink subsys (disabled) [ 0.923182] audit: type=2000 audit(0.910:1): initialized [ 0.929000] Initialise system trusted keyrings [ 0.943863] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.950416] zbud: loaded [ 0.963609] NFS: Registering the id_resolver key type [ 0.968729] Key type id_resolver registered [ 0.973009] Key type id_legacy registered [ 0.977090] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.983859] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.990409] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.997832] orangefs_debugfs_init: called with debug mask: :none: :0: [ 1.004493] orangefs_init: module version upstream loaded [ 1.012490] Key type asymmetric registered [ 1.016653] Asymmetric key parser 'x509' registered [ 1.021714] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.029160] io scheduler noop registered [ 1.033292] io scheduler deadline registered [ 1.037642] io scheduler cfq registered (default) [ 1.043377] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 1.052286] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00 [ 1.059218] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 1.065940] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 1.072899] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.078868] PCI: bus0: Fast back to back transfers disabled [ 1.084604] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.092750] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.100920] PCI: bus1: Fast back to back transfers enabled [ 1.106680] PCI: bus2: Fast back to back transfers enabled [ 1.112332] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.117362] pci 0000:00:02.0: PCI bridge to [bus 02] [ 1.122926] mv_xor f1060800.xor: Marvell shared XOR driver [ 1.181817] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.189428] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.251805] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 1.325801] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.334440] console [ttyS0] disabled [ 1.358592] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 22, base_baud = 15625000) is a 16550A [ 1.367779] console [ttyS0] enabled [ 1.367779] console [ttyS0] enabled [ 1.374879] bootconsole [earlycon0] disabled [ 1.374879] bootconsole [earlycon0] disabled [ 1.384556] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 1.393880] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 1.413760] scsi host0: ahci-mvebu [ 1.427590] scsi host1: ahci-mvebu [ 1.431263] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 41 [ 1.439293] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 41 [ 1.447858] pxa3xx-nand f10d0000.flash: This platform can't do DMA on this device [ 1.455789] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xda [ 1.462194] nand: Macronix MX30LF2G18AC [ 1.466115] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.473753] pxa3xx-nand f10d0000.flash: ECC strength 16, ECC step size 2048 [ 1.480919] Bad block table found at page 131008, version 0x01 [ 1.487254] Bad block table found at page 130944, version 0x01 [ 1.493460] 7 ofpart partitions found on MTD device pxa3xx_nand-0 [ 1.499568] Creating 7 MTD partitions on "pxa3xx_nand-0": [ 1.505013] 0x000000000000-0x000000200000 : "U-Boot" [ 1.520854] 0x000000200000-0x000000400000 : "U-Boot env" [ 1.537106] 0x000000400000-0x000000e00000 : "Config" [ 1.553006] 0x000000e00000-0x000001d00000 : "Kernel-1" [ 1.569080] 0x000001d00000-0x000008700000 : "RootFS-1" [ 1.585595] 0x000008700000-0x000009600000 : "Kernel-2" [ 1.601748] 0x000009600000-0x000010000000 : "RootFS-2" [ 1.619424] libphy: Fixed MDIO Bus: probed [ 1.624792] libphy: mdio_driver_register: mv88e6085 [ 1.630306] libphy: orion_mdio_bus: probed [ 1.639058] mvneta f1070000.ethernet eth0: Using random mac address 16:ce:f5:f5:56:6a [ 1.648009] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.654742] ehci-pci: EHCI PCI platform driver [ 1.659275] ehci-orion: EHCI orion driver [ 1.663572] orion-ehci f1058000.usb: EHCI Host Controller [ 1.668999] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 1.677547] orion-ehci f1058000.usb: irq 37, io mem 0xf1058000 [ 1.711317] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 1.717390] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.724226] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.731491] usb usb1: Product: EHCI Host Controller [ 1.736381] usb usb1: Manufacturer: Linux 4.9.0-mvebu-tld-12 ehci_hcd [ 1.742859] usb usb1: SerialNumber: f1058000.usb [ 1.747939] hub 1-0:1.0: USB hub found [ 1.751818] hub 1-0:1.0: 1 port detected [ 1.756325] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.761780] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 1.769376] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.777990] xhci-hcd f10f0000.usb3: irq 44, io mem 0xf10f0000 [ 1.783917] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.790745] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.798020] usb usb2: Product: xHCI Host Controller [ 1.802930] usb usb2: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.809403] usb usb2: SerialNumber: f10f0000.usb3 [ 1.814546] hub 2-0:1.0: USB hub found [ 1.818408] hub 2-0:1.0: 1 port detected [ 1.822568] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.827900] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 [ 1.835476] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.843701] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.850507] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.857773] usb usb3: Product: xHCI Host Controller [ 1.863430] usb usb3: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.869888] usb usb3: SerialNumber: f10f0000.usb3 [ 1.875021] hub 3-0:1.0: USB hub found [ 1.878864] hub 3-0:1.0: 1 port detected [ 1.883090] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.888428] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 1.896031] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.904655] xhci-hcd f10f8000.usb3: irq 45, io mem 0xf10f8000 [ 1.910505] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.917336] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.924597] usb usb4: Product: xHCI Host Controller [ 1.929487] usb usb4: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 1.936010] usb usb4: SerialNumber: f10f8000.usb3 [ 1.941131] hub 4-0:1.0: USB hub found [ 1.945004] hub 4-0:1.0: 1 port detected [ 1.949137] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.954499] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 [ 1.962026] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.968321] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.976554] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.983384] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.989620] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.996894] ata1.00: ATA-8: WDC WD10EARS-00Y5B1, 80.00A80, max UDMA/133 [ 1.996899] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 2.003664] ata2.00: ATA-8: WDC WD10EARS-00Y5B1, 80.00A80, max UDMA/133 [ 2.003668] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 2.010505] ata1.00: configured for UDMA/133 [ 2.024116] ata2.00: configured for UDMA/133 [ 2.028647] scsi 0:0:0:0: Direct-Access ATA WDC WD10EARS-00Y 0A80 PQ: 0 ANSI: 5 [ 2.041126] usb usb5: Product: xHCI Host Controller [ 2.046039] usb usb5: Manufacturer: Linux 4.9.0-mvebu-tld-12 xhci-hcd [ 2.052603] usb usb5: SerialNumber: f10f8000.usb3 [ 2.057731] hub 5-0:1.0: USB hub found [ 2.061611] hub 5-0:1.0: 1 port detected [ 2.065916] usbcore: registered new interface driver usblp [ 2.071634] usbcore: registered new interface driver usb-storage [ 2.077929] mousedev: PS/2 mouse device common for all mice [ 2.084137] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 2.084268] sd 0:0:0:0: [sda] Write Protect is off [ 2.084328] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.098210] sda: sda1 [ 2.098776] scsi 1:0:0:0: Direct-Access ATA WDC WD10EARS-00Y 0A80 PQ: 0 ANSI: 5 [ 2.099117] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 2.124911] armada38x-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 [ 2.133019] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 2.133148] sd 1:0:0:0: [sdb] Write Protect is off [ 2.133208] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.156525] i2c /dev entries driver [ 2.172408] orion_wdt: Initial timeout 171 sec [ 2.180314] marvell-cesa f1090000.crypto: CESA device successfully registered [ 2.188092] sdb: sdb1 [ 2.191284] sd 1:0:0:0: [sdb] Attached SCSI removable disk [ 2.196824] hidraw: raw HID events driver (C) Jiri Kosina [ 2.202909] usbcore: registered new interface driver usbhid [ 2.208497] usbhid: USB HID core driver [ 2.212659] drop_monitor: Initializing network drop monitor service [ 2.218970] Netfilter messages via NETLINK v0.30. [ 2.223819] ip_set: protocol 6 [ 2.227065] NET: Registered protocol family 10 [ 2.242168] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.249104] NET: Registered protocol family 17 [ 2.253913] 8021q: 802.1Q VLAN Support v1.8 [ 2.258132] Key type dns_resolver registered [ 2.262577] ThumbEE CPU extension supported. [ 2.266863] Registering SWP/SWPB emulation handler [ 2.272161] registered taskstats version 1 [ 2.276270] Loading compiled-in X.509 certificates [ 2.281100] zswap: loaded using pool lzo/zbud [ 2.334803] Key type big_key registered [ 2.342307] Key type encrypted registered [ 2.347569] v5.0-sata0: supplied by pwr_en_sata0 [ 2.352467] v12.0-sata0: supplied by pwr_en_sata0 [ 2.357446] v5.0-sata1: supplied by pwr_en_sata1 [ 2.362253] v12.0-sata1: supplied by pwr_en_sata1 [ 2.367694] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 2.374923] armada38x-rtc f10a3800.rtc: setting system clock to 2017-09-09 13:13:46 UTC (1504962826) [ 2.384343] v5.0-sata0: disabling [ 2.387666] v12.0-sata0: disabling [ 2.391076] v5.0-sata1: disabling [ 2.394430] v12.0-sata1: disabling [ 2.398879] Freeing unused kernel memory: 1024K (c0c00000 - c0d00000) Loading, please wait... [ 2.451977] systemd-udevd[1341]: starting version 215 [ 2.458010] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.585528] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 2.610083] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 2.758264] random: fast init done Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.25.2 fsck: error 2 (No such file or directory) while executing fsck.ext2 for /dev/sda1 fsck exited with status code 8 done. Warning: File system check failed but did not detect errors done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 20.156651] systemd-udevd[1540]: starting version 215 . ok [ ok ] Synthesizing the initial hotplug events...done. [ ok ] Waiting for /dev to be fully populated...done. [ ok ] Activating swap...done. [ 21.682887] EXT2-fs (sda1): warning: mounting unchecked fs, running e2fsck is recommended [ ok ] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.25.2 done. [ ok ] Cleaning up temporary files... /tmp. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables ...done. [ 23.457658] random: crng init done [ 23.881408] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 24.891334] mvneta f1070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 24.899202] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1 Copyright 2004-2014 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/58:8b:f3:db:dd:3e Sending on LPF/eth0/58:8b:f3:db:dd:3e Sending on Socket/fallback DHCPREQUEST on eth0 to 255.255.255.255 port 67 ^[[A DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 15 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 16 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 No DHCPOFFERS received. Trying recorded lease 192.168.178.24 PING 192.168.178.1 (192.168.178.1) 56(84) bytes of data. --- 192.168.178.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms bound: immediate renewal. DHCPREQUEST on eth0 to 192.168.178.1 port 67 send_packet: Network is unreachable send_packet: please consult README file regarding broadcast address. dhclient.c:2243: Failed to send 300 byte long packet over fallback interface. done. [ ok ] Starting rpcbind daemon.... [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 2435 (syslogd) . ok [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting periodic command scheduler: cron. [ ok ] Starting system message bus: dbus. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 2434 (klogd) . ok [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Starting MariaDB database server: mysqld .. Debian GNU/Linux 8 debian ttyS0 debian login:
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's September 09, 2017 05:12PM |
Admin Registered: 13 years ago Posts: 18,575 |
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's September 11, 2017 04:03PM |
Registered: 6 years ago Posts: 23 |
pi@raspberrypi:~ $ cd Downloads/ pi@raspberrypi:~/Downloads $ sudo ./kwboot -t -B 115200 /dev/ttyUSB0 -d Sending debug message. Please reboot the target...- [Type Ctrl-\ + c to quit] M - 1.73 Booting from NAND flash General initialization - Version: 1.0.0 Detected Device ID 6810 High speed PHY - Version: 2.0 Init RD NAS topology board SerDes lanes topology details: | Lane # | Speed | Type | -------------------------------- | 0 | 06 | SATA0 | | 1 | 05 | USB3 HOST0 | | 2 | 06 | SATA1 | | 5 | 05 | USB3 HOST1 | -------------------------------- High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.26.0 mvSysEnvGetTopologyUpdateInfo: TWSI Read failed DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully Not detected suspend to RAM indication BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01-svn48023 (Oct 13 2015 - 09:25:56) Marvell version: 2014_T3.0p6 Board: RD-NAS-88F6820-DDR3 SoC: MV88F6810 Rev A0 running 1 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 250 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB Map: Code: 0x1fed0000:0x1ff95d60 BSS: 0x1ffef2b4 Stack: 0x1f9cff20 Heap: 0x1f9d0000:0x1fed0000 U-Boot Environment: 0x00200000:0x00280000 (NAND) NAND: 256 MiB MMC: mv_sdh: 0 *** Booting kernel from kernel 1 @0x00000000; run bootcmd_custom; *** USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | 0x01 | egiga0 [PRIME] Hit any key to stop autoboot: 0 NAND read: device 0 whole chip Attempt to read outside the flash area 0 bytes read: ERROR running scan_disk ... Scan device usb (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 2) : USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found device usb 0:1 ** Bad device usb 0 ** device usb 1:1 ** Bad device usb 1 ** device usb 2:1 ** Bad device usb 2 ** device usb 3:1 ** Bad device usb 3 ** Scan device scsi AHCI init for unit0 Target spinup took 0 ms. Target spinup took 0 ms. Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found scanning bus for devices... Device 0: (0:0) Vendor: ATA Prod.: Rev: Type: Hard Disk Capacity: not available timeout exit! Found 1 device(s). device scsi 0:1 1 bytes read in 109 ms (0 Bytes/s) Found bootable drive on scsi 0 Booting from scsi 0:1 ... loading Image ... 4021296 bytes read in 145 ms (26.4 MiB/s) loading DTB /boot/dts/armada-380-zyxel-nas326.dtb ... 18589 bytes read in 127 ms (142.6 KiB/s) loading uInitrd ... 7070236 bytes read in 204 ms (33.1 MiB/s) * kernel: cmdline image address = 0x02000000 ## Loading init Ramdisk from Legacy Image at 02900000 ... Image Name: initramfs-4.12.4-mvebu-tld-1 Created: 2017-08-22 11:10:43 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7070172 Bytes = 6.7 MiB Load Address: 00000000 Entry Point: 00000000 ## Flattened Device Tree blob at 01000000 Booting using the fdt blob at 0x01000000 Loading Ramdisk to 1f310000, end 1f9ce1dc ... OK Loading Device Tree to 00ff8000, end 00fff89c ... OK Skipping Device Tree update ('fdt_skip_update' = yes) Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.4-mvebu-tld-1 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #1 SMP PREEMPT Sat Jul 29 21:56:37 PDT 2017 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Zyxel NAS326 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 17 pages/cpu @dfbd7000 s40460 r8192 d20980 u69632 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=armada-nand:2m(u-boot),2m(env),2m(config),15m(kernel1),110m(rootfs1),15m(kernel2),-(rootfs2) earlyprintk=serial [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 499324K/524288K available (8192K kernel code, 712K rwdata, 2080K rodata, 1024K init, 331K bss, 24964K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db2308 ( 713 kB) [ 0.000000] .bss : 0xc0db9a84 - 0xc0e0ca58 ( 332 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 D prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001 [ 0.000000] Switching to timer-based delay loop, resolution 40ns [ 0.000004] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns [ 0.007883] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.019126] Console: colour dummy device 80x30 [ 0.023641] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000) [ 0.034034] pid_max: default: 32768 minimum: 301 [ 0.038788] Security Framework initialized [ 0.042986] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.049661] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.057160] CPU: Testing write buffer coherency: ok [ 0.062235] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.103753] Setting up static identity map for 0x100000 - 0x100060 [ 0.110069] mvebu-soc-id: MVEBU SoC ID=0x6810, Rev=0x4 [ 0.115374] mvebu-pmsu: Initializing Power Management Service Unit [ 0.173660] smp: Bringing up secondary CPUs ... [ 0.178256] smp: Brought up 1 node, 1 CPU [ 0.182331] SMP: Total of 1 processors activated (50.00 BogoMIPS). [ 0.188579] CPU: All CPU(s) started in SVC mode. [ 0.193723] devtmpfs: initialized [ 0.203730] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.211631] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.221552] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.227888] prandom: seed boundary self test passed [ 0.234869] prandom: 100 self tests passed [ 0.239030] pinctrl core: initialized pinctrl subsystem [ 0.244999] NET: Registered protocol family 16 [ 0.250057] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.263606] cpuidle: using governor ladder [ 0.267785] cpuidle: using governor menu [ 0.271877] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.279951] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.286066] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling [ 0.294229] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling [ 0.374659] vgaarb: loaded [ 0.377684] SCSI subsystem initialized [ 0.383892] usbcore: registered new interface driver usbfs [ 0.389758] usbcore: registered new interface driver hub [ 0.395234] usbcore: registered new device driver usb [ 0.400741] media: Linux media interface: v0.10 [ 0.405621] Linux video capture interface: v2.00 [ 0.411436] clocksource: Switched to clocksource armada_370_xp_clocksource [ 0.459049] VFS: Disk quotas dquot_6.6.0 [ 0.463119] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.479644] NET: Registered protocol family 2 [ 0.484901] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.492060] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.498589] TCP: Hash tables configured (established 4096 bind 4096) [ 0.505430] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.511329] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.517798] NET: Registered protocol family 1 [ 0.542536] RPC: Registered named UNIX socket transport module. [ 0.548512] RPC: Registered udp transport module. [ 0.553309] RPC: Registered tcp transport module. [ 0.558075] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.564688] Unpacking initramfs... [ 0.842139] Freeing initrd memory: 6908K [ 0.846229] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.853018] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.862206] audit: initializing netlink subsys (disabled) [ 0.868025] audit: type=2000 audit(0.846:1): state=initialized audit_enabled=0 res=1 [ 0.876280] Initialise system trusted keyrings [ 0.876306] Key type blacklist registered [ 0.876410] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.876469] zbud: loaded [ 0.904972] NFS: Registering the id_resolver key type [ 0.910090] Key type id_resolver registered [ 0.914379] Key type id_legacy registered [ 0.918461] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.925230] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.931764] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.939162] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.945845] orangefs_init: module version upstream loaded [ 0.954129] Key type asymmetric registered [ 0.958292] Asymmetric key parser 'x509' registered [ 0.963346] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.970791] io scheduler noop registered [ 0.974854] io scheduler deadline registered [ 0.979219] io scheduler cfq registered (default) [ 0.985057] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 0.993929] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00 [ 1.000861] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 1.007587] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 1.014545] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.020466] PCI: bus0: Fast back to back transfers disabled [ 1.026289] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.034376] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.042592] PCI: bus1: Fast back to back transfers enabled [ 1.048307] PCI: bus2: Fast back to back transfers enabled [ 1.053926] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.058956] pci 0000:00:02.0: PCI bridge to [bus 02] [ 1.064532] mv_xor f1060800.xor: Marvell shared XOR driver [ 1.131932] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy sg intr ) [ 1.139803] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.201919] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy sg intr ) [ 1.273153] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.281400] console [ttyS0] disabled [ 1.306025] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 22, base_baud = 15625000) is a 16550A [ 1.315144] console [ttyS0] enabled [ 1.315144] console [ttyS0] enabled [ 1.322243] bootconsole [earlycon0] disabled [ 1.322243] bootconsole [earlycon0] disabled [ 1.331930] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 1.341004] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 1.361018] scsi host0: ahci-mvebu [ 1.374854] scsi host1: ahci-mvebu [ 1.378519] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 41 [ 1.386549] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 41 [ 1.395129] pxa3xx-nand f10d0000.flash: This platform can't do DMA on this device [ 1.403061] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xda [ 1.409431] nand: Macronix MX30LF2G18AC [ 1.413379] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.420997] pxa3xx-nand f10d0000.flash: ECC strength 16, ECC step size 2048 [ 1.428187] Bad block table found at page 131008, version 0x01 [ 1.434519] Bad block table found at page 130944, version 0x01 [ 1.440639] 7 ofpart partitions found on MTD device pxa3xx_nand-0 [ 1.446776] Creating 7 MTD partitions on "pxa3xx_nand-0": [ 1.452213] 0x000000000000-0x000000200000 : "U-Boot" [ 1.468053] 0x000000200000-0x000000400000 : "U-Boot env" [ 1.484284] 0x000000400000-0x000000e00000 : "Config" [ 1.500086] 0x000000e00000-0x000001d00000 : "Kernel-1" [ 1.516151] 0x000001d00000-0x000008700000 : "RootFS-1" [ 1.532614] 0x000008700000-0x000009600000 : "Kernel-2" [ 1.548660] 0x000009600000-0x000010000000 : "RootFS-2" [ 1.566606] libphy: Fixed MDIO Bus: probed [ 1.572382] libphy: orion_mdio_bus: probed [ 1.580810] mvneta f1070000.ethernet eth0: Using random mac address 52:90:b2:fb:88:e8 [ 1.590100] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.596887] ehci-pci: EHCI PCI platform driver [ 1.601571] ehci-orion: EHCI orion driver [ 1.605716] orion-ehci f1058000.usb: EHCI Host Controller [ 1.611143] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 1.618940] orion-ehci f1058000.usb: irq 37, io mem 0xf1058000 [ 1.651450] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 1.657523] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.664368] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.671632] usb usb1: Product: EHCI Host Controller [ 1.676523] usb usb1: Manufacturer: Linux 4.12.4-mvebu-tld-1 ehci_hcd [ 1.683002] usb usb1: SerialNumber: f1058000.usb [ 1.688015] hub 1-0:1.0: USB hub found [ 1.691903] hub 1-0:1.0: 1 port detected [ 1.696389] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.701842] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 1.709439] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.718049] xhci-hcd f10f0000.usb3: irq 44, io mem 0xf10f0000 [ 1.723971] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.730796] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.738080] usb usb2: Product: xHCI Host Controller [ 1.742998] usb usb2: Manufacturer: Linux 4.12.4-mvebu-tld-1 xhci-hcd [ 1.749476] usb usb2: SerialNumber: f10f0000.usb3 [ 1.754580] hub 2-0:1.0: USB hub found [ 1.758440] hub 2-0:1.0: 1 port detected [ 1.762576] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.767909] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 [ 1.775483] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.783709] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.790515] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.797779] usb usb3: Product: xHCI Host Controller [ 1.802825] usb usb3: Manufacturer: Linux 4.12.4-mvebu-tld-1 xhci-hcd [ 1.809282] usb usb3: SerialNumber: f10f0000.usb3 [ 1.814377] hub 3-0:1.0: USB hub found [ 1.818218] hub 3-0:1.0: 1 port detected [ 1.822444] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.827781] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 1.835377] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.843996] xhci-hcd f10f8000.usb3: irq 45, io mem 0xf10f8000 [ 1.849839] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.856671] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.863931] usb usb4: Product: xHCI Host Controller [ 1.868821] usb usb4: Manufacturer: Linux 4.12.4-mvebu-tld-1 xhci-hcd [ 1.875341] usb usb4: SerialNumber: f10f8000.usb3 [ 1.880434] hub 4-0:1.0: USB hub found [ 1.884307] hub 4-0:1.0: 1 port detected [ 1.888417] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.893778] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 [ 1.901332] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.909533] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.916371] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.922655] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.928888] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.936216] usb usb5: Product: xHCI Host Controller [ 1.941107] usb usb5: Manufacturer: Linux 4.12.4-mvebu-tld-1 xhci-hcd [ 1.947592] ata1.00: ATA-8: WDC WD10EARS-00Y5B1, 80.00A80, max UDMA/133 [ 1.947596] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 1.947619] ata2.00: ATA-8: WDC WD10EARS-00Y5B1, 80.00A80, max UDMA/133 [ 1.947623] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 1.967789] ata1.00: configured for UDMA/133 [ 1.967816] ata2.00: configured for UDMA/133 [ 1.983305] usb usb5: SerialNumber: f10f8000.usb3 [ 1.988261] scsi 0:0:0:0: Direct-Access ATA WDC WD10EARS-00Y 0A80 PQ: 0 ANSI: 5 [ 1.989024] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 1.989057] sd 0:0:0:0: [sda] Write Protect is off [ 1.989116] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.006121] sda: sda1 [ 2.006881] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 2.011937] scsi 1:0:0:0: Direct-Access ATA WDC WD10EARS-00Y 0A80 PQ: 0 ANSI: 5 [ 2.012649] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 2.012681] sd 1:0:0:0: [sdb] Write Protect is off [ 2.012739] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.061153] hub 5-0:1.0: USB hub found [ 2.065034] hub 5-0:1.0: 1 port detected [ 2.069330] usbcore: registered new interface driver usblp [ 2.075111] usbcore: registered new interface driver usb-storage [ 2.081377] mousedev: PS/2 mouse device common for all mice [ 2.087528] sdb: sdb1 [ 2.090595] sd 1:0:0:0: [sdb] Attached SCSI removable disk [ 2.096761] armada38x-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 [ 2.104878] i2c /dev entries driver [ 2.119981] (NULL device *): hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info(). [ 2.132752] orion_wdt: Initial timeout 171 sec [ 2.140529] marvell-cesa f1090000.crypto: CESA device successfully registered [ 2.148067] hidraw: raw HID events driver (C) Jiri Kosina [ 2.154058] usbcore: registered new interface driver usbhid [ 2.159645] usbhid: USB HID core driver [ 2.163851] drop_monitor: Initializing network drop monitor service [ 2.170168] Netfilter messages via NETLINK v0.30. [ 2.175116] ip_set: protocol 6 [ 2.178372] NET: Registered protocol family 10 [ 2.193437] Segment Routing with IPv6 [ 2.197148] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.204120] NET: Registered protocol family 17 [ 2.208608] 8021q: 802.1Q VLAN Support v1.8 [ 2.213016] Key type dns_resolver registered [ 2.217396] ThumbEE CPU extension supported. [ 2.221711] Registering SWP/SWPB emulation handler [ 2.226978] registered taskstats version 1 [ 2.231085] Loading compiled-in X.509 certificates [ 2.236079] zswap: loaded using pool lzo/zbud [ 2.292315] Key type big_key registered [ 2.299686] Key type encrypted registered [ 2.305174] v5.0-sata0: supplied by pwr_en_sata0 [ 2.309834] v12.0-sata0: supplied by pwr_en_sata0 [ 2.315560] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 2.322799] armada38x-rtc f10a3800.rtc: setting system clock to 2017-09-11 20:20:14 UTC (1505161214) [ 2.332249] v5.0-sata1: supplied by pwr_en_sata1 [ 2.336920] v12.0-sata1: supplied by pwr_en_sata1 [ 2.341738] v5.0-sata0: disabling [ 2.345062] v12.0-sata0: disabling [ 2.348471] v5.0-sata1: disabling [ 2.351843] v12.0-sata1: disabling [ 2.356262] Freeing unused kernel memory: 1024K Loading, please wait... starting version 232 [ 2.411335] random: udevadm: uninitialized urandom read (16 bytes read) [ 2.419485] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.419736] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.419788] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.444516] random: udevadm: uninitialized urandom read (16 bytes read) [ 2.451189] random: udevadm: uninitialized urandom read (16 bytes read) [ 2.458269] random: udevadm: uninitialized urandom read (16 bytes read) [ 2.465186] random: udevadm: uninitialized urandom read (16 bytes read) [ 2.472120] random: udevadm: uninitialized urandom read (16 bytes read) [ 2.478987] random: udevadm: uninitialized urandom read (16 bytes read) Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Warning: fsck not present, so sk[ 13.430680] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem ipping root file system [ 13.447400] random: fast init done [ 13.487535] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [ ok ] Setting hostname to 'debian'...done. [....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232 . ok [ ok ] Synthesizing the initial hotplug events...done. [....] Waiting for /dev to be fully populated...[ 16.369012] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 16.406857] sd 1:0:0:0: Attached scsi generic sg1 type 0 done. [ ok ] Activating swap:. [ 17.473939] EXT4-fs (sda1): re-mounted. Opts: (null) [....] Will now check root file system:fsck from util-linux 2.29.2 [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sda1 e2fsck 1.43.4 (31-Jan-2017) rootfs: clean, 22020/61054976 files, 4320801/244190208 blocks . ok [ 19.256523] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ ok ] Will now activate lvm and md swap:done. [info] Will now check all file systems. fsck from util-linux 2.29.2 Checking all file systems. LABEL=rootfs is mounted [ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. [ 19.804260] random: crng init done [ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done. [ ok . [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables...done. [ ok ] Initializing random number generator...done. [ 21.203295] m88e1318_get_wol: phy_id = 0x1410dd1 OK [ 21.208323] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5 Copyright 2004-2016 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/58:8b:f3:db:dd:3e Sending on LPF/eth0/58:8b:f3:db:dd:3e Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 [ 25.381894] mvneta f1070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 25.389936] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 14 DHCPREQUEST of 192.168.178.43 on eth0 to 255.255.255.255 port 67 DHCPOFFER of 192.168.178.43 from 192.168.178.1 DHCPACK of 192.168.178.43 from 192.168.178.1 invoke-rc.d: could not determine current runlevel bound to 192.168.178.43 -- renewal in 410047 seconds. done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 2600 (syslogd) . ok [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting periodic command scheduler: cron. [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [ ok ] Starting OpenBSD Secure Shell server: sshd. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 2601 (klogd) . ok [ ok ] Starting NTP server: ntpd. [ ok ] Running local boot scripts (/etc/rc.local). Debian GNU/Linux 9 debian ttyS0 debian login:
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's September 11, 2017 07:17PM |
Admin Registered: 13 years ago Posts: 18,575 |
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's September 13, 2017 12:13PM |
Registered: 6 years ago Posts: 23 |
pi@raspberrypi:~ $ cd Downloads/ pi@raspberrypi:~/Downloads $ sudo ./kwboot -t -B 115200 /dev/ttyUSB0 -d Sending debug message. Please reboot the target...| [Type Ctrl-\ + c to quit] M - 1.73 Booting from NAND flash General initialization - Version: 1.0.0 Detected Device ID 6810 High speed PHY - Version: 2.0 Init RD NAS topology board SerDes lanes topology details: | Lane # | Speed | Type | -------------------------------- | 0 | 06 | SATA0 | | 1 | 05 | USB3 HOST0 | | 2 | 06 | SATA1 | | 5 | 05 | USB3 HOST1 | -------------------------------- High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.26.0 mvSysEnvGetTopologyUpdateInfo: TWSI Read failed DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully Not detected suspend to RAM indication BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01-svn48023 (Oct 13 2015 - 09:25:56) Marvell version: 2014_T3.0p6 Board: RD-NAS-88F6820-DDR3 SoC: MV88F6810 Rev A0 running 1 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 250 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB Map: Code: 0x1fed0000:0x1ff95d60 BSS: 0x1ffef2b4 Stack: 0x1f9cff20 Heap: 0x1f9d0000:0x1fed0000 U-Boot Environment: 0x00200000:0x00280000 (NAND) NAND: 256 MiB MMC: mv_sdh: 0 *** Booting kernel from kernel 1 @0x00000000; run bootcmd_custom; *** USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | 0x01 | egiga0 [PRIME] Hit any key to stop autoboot: 0 NAND read: device 0 whole chip Attempt to read outside the flash area 0 bytes read: ERROR running scan_disk ... Scan device usb (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 2) : USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found device usb 0:1 ** Bad device usb 0 ** device usb 1:1 ** Bad device usb 1 ** device usb 2:1 ** Bad device usb 2 ** device usb 3:1 ** Bad device usb 3 ** Scan device scsi AHCI init for unit0 Target spinup took 0 ms. Target spinup took 0 ms. Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found scanning bus for devices...
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's September 13, 2017 06:27PM |
Admin Registered: 13 years ago Posts: 18,575 |
Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found scanning bus for devices...
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's September 14, 2017 02:59PM |
Registered: 6 years ago Posts: 23 |
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's September 15, 2017 12:14AM |
Admin Registered: 13 years ago Posts: 18,575 |
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's September 16, 2017 04:16AM |
Registered: 6 years ago Posts: 23 |
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's September 18, 2017 02:52PM |
Registered: 6 years ago Posts: 23 |
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's September 18, 2017 06:54PM |
Admin Registered: 13 years ago Posts: 18,575 |
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's September 19, 2017 03:40PM |
Registered: 6 years ago Posts: 23 |
Re: Problem booting Debian-4.9.0-mvebu-tld-12 with 2 hdd's October 01, 2017 11:26AM |
Registered: 6 years ago Posts: 23 |