Installation: Lenny works, Squeeze fails

Hi,

I can't install Debian Squeeze with Jeff's Squeeze Installation Script. After some power-off tries, it boots, but I can't reach it. The LED shines green. Ping/SSH are down. I tried it three times, but nothing happens.

The Lenny Installation Script works fine and after that I can upgrade it to Squeeze.

Any ideas or suggestions?


Regards,
Christian

Output from netconsole:

U-Boot 2010.09 (Oct 23 2010 - 11:49:22)
Marvell-Dockstar/Pogoplug by Jeff Doozan
Hit any key to stop autoboot:  0
(Re)start USB...
USB:   Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
       scanning bus for storage devices... error in inquiry
0 Storage Device(s) found
** Block device usb 0 not supported

** Invalid boot device **

Output from fw_printenv:

Pogoplug:/tmp$ /usr/sbin/fw_printenv
ethact=egiga0
bootdelay=3
baudrate=115200
mainlineLinux=yes
console=ttyS0,115200
led_init=green blinking
led_exit=green off
led_error=orange blinking
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
mtdids=nand0=orion_nand
partition=nand0,2
stdin=serial
stdout=serial
stderr=serial
rescue_installed=0
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done
usb_scan_list=1 2 3 4
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_init=run usb_scan
usb_device=0:1
usb_root=/dev/sda1
usb_rootfstype=ext2
usb_rootdelay=10
usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
ethaddr=**:**:**:**:**:**
arcNumber=2097
serverip=192.168.***.***
ipaddr=192.168.***.***
if_netconsole=ping $serverip
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
preboot=run if_netconsole start_netconsole

Any ideas? Why is my USB HDD not supported?

btw: I'll try it with an USB-Stick...


Regards,
Christian

killerbees19 Wrote:
-------------------------------------------------------
> Any ideas? Why is my USB HDD not supported?
>
> btw: I'll try it with an USB-Stick...

Same problem with a SUPER TALENT Pico-C 4GB USB-Stick:

U-Boot 2010.09 (Oct 23 2010 - 11:49:22)
Marvell-Dockstar/Pogoplug by Jeff Doozan
Hit any key to stop autoboot:  0
(Re)start USB...
USB:   Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
       scanning bus for storage devices... error in inquiry
0 Storage Device(s) found
** Block device usb 0 not supported

** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=3"
UBI: MTD device size:            219 MiB
UBI: number of good PEBs:        1750
UBI: number of bad PEBs:         2
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     0
UBI: available PEBs:             1729
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..

I've tried it with two USB-Sticks of that type. Everyone prepared with fdisk:

# fdisk

d

n
p
1
<EMPTY>
+3000M

n
p
2
<EMPTY>
<EMPTY>

t
1
83

t
2
82

a
1

w
q

Update: After some restarts...

scanning bus for devices... 3 USB Device(s) found
       scanning bus for storage devices... Device NOT ready
   Request Sense returned 00 00 00
1 Storage Device(s) found
** Bad partition 1 **
Device NOT ready
   Request Sense returned 00 00 00
** Can't read from device 0 **

** Unable to use usb 0:1 for fatload **

Regards,
Christian



Edited 1 time(s). Last edit at 01/31/2011 05:59AM by killerbees19.

Update: I've tested >10 USB-Sticks and USB-HDD's, some of them are working and booting, but only with Lenny. With Squeeze, the Kernel is loaded, but nothing happens...


Regards,
Christian

I think I've found the reason: The two "/usr/bin/mkimage" lines from the installer don't work at my Dockstar's. I don't know why, but the solution is really simple :-)

mount proc /mnt/proc -t proc
mount sysfs /mnt/sys -t sysfs

chroot /mnt /usr/sbin/flash-kernel 2.6.32-5-kirkwood

In my example the new Debian-System is mounted to /mnt. After that reboot your Dockstar into your new Debian-System. Now it works without any problems.


Regards,
Christian