Welcome! Log In Create A New Profile

Advanced

NSA325 - stock u-boot problem booting with Linux Kernel 4.13.5

Posted by dummy64 
Hello Bohdi,

I'm having some issues upgrading the kernel from 4.8.3 to 4.13.5 with an NSA325.
System has been upgraded from jessie to stretch vía apt

I've followed your tutorial and did the 4b point because I don't want to mess with my uboot.

i've done:
cd /boot
tar -xjf linux-4.13.5-kirkwood-tld-1-bodhi.tar.bz2
tar -xf  linux-dtb-4.13.5-kirkwood-tld-1.tar

cd /boot
apt-get remove flash-kernel 
dpkg -i linux-image-4.13.5-kirkwood-tld-1_1.0_armel.deb

cp -a zImage-4.13.5-kirkwood-tld-1  zImage.fdt
cat dts/kirkwood-nsa325.dtb >> zImage.fdt
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-4.13.5-kirkwood-tld-1 -d zImage.fdt  uImage
mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-4.13.5-kirkwood-tld-1 -d initrd.img-4.13.5-kirkwood-tld-1 uInitrd

My uBoot output:
         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|
 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Jul 18 2013 - 10:47:29) Marvell version: 3.5.9

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CFB00

Soc: 88F6282 A1CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 8 tRAS = 24 tRCD=8
DRAM CS[0] base 0x00000000   size 512MB
DRAM Total size 512MB  16bit width
Addresses 10M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (10M - 7M): Done
NAND:128 MB
Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)
Kernel address is 0x4640000.

Streaming disabled
Write allocate disabled


USB 0: host mode
        [BlueDBG] reseting SoC Pex[0]  0 ...
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
        [BlueDBG] reseting SoC Pex[1]  0 ...
        [BlueDBG] reseting SoC Pex[1]  1 ...
        [BlueDBG] reseting SoC Pex[1]  2 ...
        [BlueDBG] reseting SoC Pex[1]  3 ...
        [BlueDBG] reseting SoC Pex[1]  4 ...
        [BlueDBG] reseting SoC Pex[1]  5 ...
        [BlueDBG] reseting SoC Pex[1]  6 ...
        [BlueDBG] reseting SoC Pex[1]  7 ...
        [BlueDBG] reseting SoC Pex[1]  8 ...
        [BlueDBG] reseting SoC Pex[1]  9 ...
        [BlueDBG] reseting SoC Pex[1]  10 ...
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
(Re)start USB...
USB:   scanning bus for devices... 3 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
....
8386386 bytes read
## Booting image at 02000000 ...
   Image Name:   Linux-4.13.5-kirkwood-tld-1
   Created:      2017-10-12  16:12:18 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3862548 Bytes =  3.7 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
   Image Name:   initramfs-4.13.5-kirkwood-tld-1
   Created:      2017-10-12  16:12:32 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    8386322 Bytes =  8 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
_

am I skipping something? could be that the image is broken?

Files in /boot
drwxrwxrwx 4 root root 1.0K Oct 12 16:12 .
drwxr-xr-x 6 root root 4.0K Oct 12 15:13 ..
-rw-r--r-- 1 root root 152K Oct  7 08:53 config-4.13.5-kirkwood-tld-1
-rw-r--r-- 1 root root 143K Oct 21  2016 config-4.8.3-kirkwood-tld-1
drwxr-xr-x 2 root root 5.0K Sep 20 08:13 dts
-rw-r--r-- 1 root root 8.0M Oct 12 14:24 initrd.img-4.13.5-kirkwood-tld-1
-rw-r--r-- 1 root root 8.2M Oct  9 22:49 initrd.img-4.8.3-kirkwood-tld-1
-rw-r--r-- 1 root root 141K Dec  8  2016 linux-4.8.3-kirkwood-tld-1.patch
drwx------ 2 root root 1.0K Dec  8  2016 lost+found
-rw------- 1 root root 2.5M Oct  7 11:26 System.map-4.13.5-kirkwood-tld-1
-rw------- 1 root root 2.3M Oct 21  2016 System.map-4.8.3-kirkwood-tld-1
-rw-r--r-- 1 root root 3.7M Oct 12 16:12 uImage
-rw-r--r-- 1 root root 8.0M Oct 12 16:12 uInitrd
-rw------- 1 root root 3.7M Oct  7 11:26 vmlinuz-4.13.5-kirkwood-tld-1
-rw------- 1 root root 3.1M Oct 21  2016 vmlinuz-4.8.3-kirkwood-tld-1
-rwxr-xr-x 1 root root 3.7M Oct  7 06:56 zImage-4.13.5-kirkwood-tld-1
-rwxr-xr-x 1 root root 3.1M Dec  8  2016 zImage-4.8.3-kirkwood-tld-1
-rwxr-xr-x 1 root root 3.7M Oct 12 16:11 zImage.fdt

# file uImage
uImage: u-boot legacy uImage, Linux-4.13.5-kirkwood-tld-1, Linux/ARM, OS Kernel Image (Not compressed), 3862548 bytes, Thu Oct 12 16:12:18 2017, Load Address: 0x00008000, Entry Point: 0x00008000, Header CRC: 0x3E922991, Data CRC: 0x0313BB48

# file uInitrd
uInitrd: u-boot legacy uImage, initramfs-4.13.5-kirkwood-tld-1, Linux/ARM, RAMDisk Image (gzip), 8386322 bytes, Thu Oct 12 16:12:32 2017, Load Address: 0x00000000, Entry Point: 0x00000000, Header CRC: 0x8F561567, Data CRC: 0x55FE9383

I've rolled back to 4.8.3 restoring uImage and Uinitrd files and it works

Regards


------------
Mod edit: change subject decription.



Edited 2 time(s). Last edit at 10/12/2017 02:51PM by bodhi.
Re: NSA325 - Problem booting with Linux Kernel 4.13.5
October 12, 2017 02:50PM
dummy64,

Your kernel files look OK. I recognized this booting problem with stock u-boot. However, to be sure, I need to see your u-boot envs.

Reboot, interrupt serial console and get the listing of your u-boot envs and post here:

printenv

-bodhi
===========================
Forum Wiki
bodhi's corner
Hello Bodhi,

Here is my environment. I'm booting from a 32GB SanDisk Ultra Fit USB 3.0 pendrive located in the first USB port. I don't have any experience with uboot enviroments and tampering with it gives me a little respect.

Marvell>> printenv
bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
bootdelay=2
baudrate=115200
loads_echo=0
ipaddr=10.4.52.165
serverip=10.4.52.7
rootpath=/srv/ubuntu
netmask=255.255.255.0
nandEcc=1bit
MODEL_ID=AE03
PRODUCT_NAME=NSA-325v2
FEATURE_BIT=00
CONTRY_TYPE=FF
VENDOR_NAME=MitraStar Technology Corp.
run_diag=yes
console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root)
ethprime=egiga0
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
lcd0_enable=0
lcd0_params=640x480-16@60
ethaddr=00:50:43:00:02:02
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
image_multi=yes
ethact=egiga0
arcNumber=4495
bootargs_stock=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
bootargs_linux=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=LABEL=rootfs loglevel=8
bootcmd_linux=setenv bootargs $(bootargs_linux); mw.l f1010100 0020c000; usb reset; ext2load usb 0:1 $(loadaddr) /uImage; ext2load usb 0:1 0x01100000 /uInitrd; bootm $(loadaddr) 0x01100000
bootcmd_stock=setenv bootargs $(bootargs_stock); nand read.e $(loadaddr) $(kernel_addr) 0xA00000; bootm $(loadadr)
to_stock=setenv mainlineLinux no; setenv bootcmd \'run bootcmd_stock\'; saveenv; reset
to_linux=setenv mainlineLinux yes; setenv bootcmd \'run bootcmd_linux\'; saveenv; reset
bootcmd='run bootcmd_linux'
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
disaMvPnp=no
enaAutoRecovery=yes
kernel_addr=0x4640000
pcieTune=no
pcieTune1=no

Environment size: 2498/131068 bytes

Thank you.
Regards
Re: NSA325 - Problem booting with Linux Kernel 4.13.5
October 13, 2017 12:18AM
dummy64,

1. Your current posted envs do not look like the same as ones used in in the bootlog previously.

Quote

__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Jul 18 2013 - 10:47:29) Marvell version: 3.5.9

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00

Soc: 88F6282 A1CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 8 tRAS = 24 tRCD=8
DRAM CS[0] base 0x00000000 size 512MB
DRAM Total size 512MB 16bit width
Addresses 10M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (10M - 7M): Done
NAND:128 MB
Flash: 0 kB

CPU : Marvell Feroceon (Rev 1)
Kernel address is 0x4640000.

Streaming disabled
Write allocate disabled


USB 0: host mode
[BlueDBG] reseting SoC Pex[0] 0 ...
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
[BlueDBG] reseting SoC Pex[1] 0 ...
[BlueDBG] reseting SoC Pex[1] 1 ...
[BlueDBG] reseting SoC Pex[1] 2 ...
[BlueDBG] reseting SoC Pex[1] 3 ...
[BlueDBG] reseting SoC Pex[1] 4 ...
[BlueDBG] reseting SoC Pex[1] 5 ...
[BlueDBG] reseting SoC Pex[1] 6 ...
[BlueDBG] reseting SoC Pex[1] 7 ...
[BlueDBG] reseting SoC Pex[1] 8 ...
[BlueDBG] reseting SoC Pex[1] 9 ...
[BlueDBG] reseting SoC Pex[1] 10 ...
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices... 3 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
....
8386386 bytes read
## Booting image at 02000000 ...
Image Name: Linux-4.13.5-kirkwood-tld-1
Created: 2017-10-12 16:12:18 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3862548 Bytes = 3.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
Image Name: initramfs-4.13.5-kirkwood-tld-1
Created: 2017-10-12 16:12:32 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 8386322 Bytes = 8 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

That's not helpful in troubleshooting!


2. However, let's forget about that boot log above.

Here is how you can try booting with the current envs.

Power up, interrup serial console and

setenv bootargs_linux 'console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=LABEL=rootfs loglevel=8 earlyprintk=serial'
setenv bootcmd_linux 'setenv bootargs $(bootargs_linux); mw.l f1010100 0020c000; usb reset; ext2load usb 0:1 $(loadaddr) /boot/uImage; ext2load usb 0:1 0x02100000 /boot/uInitrd; bootm $(loadaddr) 0x02100000'
printenv
boot

And please post the entire serial console log here.

-bodhi
===========================
Forum Wiki
bodhi's corner



Edited 1 time(s). Last edit at 10/13/2017 12:20AM by bodhi.
Hello Bodhi,

I did as you told, it is not booting.
Seems like is searching for a certain path with these changes.

I'm sorry I didn't told you earlier that the first partition is a dedicated /boot partition.
the rest of the system is located in the second partition.
Both are ext2 partitions. I didn't moved any USB drives. I only put again the newer kernel files

Log attached below:
         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|
 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Jul 18 2013 - 10:47:29) Marvell version: 3.5.9

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CFB00

Soc: 88F6282 A1CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 8 tRAS = 24 tRCD=8
DRAM CS[0] base 0x00000000   size 512MB
DRAM Total size 512MB  16bit width
Addresses 10M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (10M - 7M): Done
NAND:128 MB
Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)
Kernel address is 0x4640000.

Streaming disabled
Write allocate disabled


USB 0: host mode
        [BlueDBG] reseting SoC Pex[0]  0 ...
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
        [BlueDBG] reseting SoC Pex[1]  0 ...
        [BlueDBG] reseting SoC Pex[1]  1 ...
        [BlueDBG] reseting SoC Pex[1]  2 ...
        [BlueDBG] reseting SoC Pex[1]  3 ...
        [BlueDBG] reseting SoC Pex[1]  4 ...
        [BlueDBG] reseting SoC Pex[1]  5 ...
        [BlueDBG] reseting SoC Pex[1]  6 ...
        [BlueDBG] reseting SoC Pex[1]  7 ...
        [BlueDBG] reseting SoC Pex[1]  8 ...
        [BlueDBG] reseting SoC Pex[1]  9 ...
        [BlueDBG] reseting SoC Pex[1]  10 ...
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Marvell>> printenv
bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
bootdelay=2
baudrate=115200
loads_echo=0
ipaddr=10.4.52.165
serverip=10.4.52.7
rootpath=/srv/ubuntu
netmask=255.255.255.0
nandEcc=1bit
MODEL_ID=AE03
PRODUCT_NAME=NSA-325v2
FEATURE_BIT=00
CONTRY_TYPE=FF
VENDOR_NAME=MitraStar Technology Corp.
run_diag=yes
console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root)
ethprime=egiga0
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
lcd0_enable=0
lcd0_params=640x480-16@60
ethaddr=00:50:43:00:02:02
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
image_multi=yes
ethact=egiga0
arcNumber=4495
bootargs_stock=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
bootargs_linux=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=LABEL=rootfs loglevel=8
bootcmd_linux=setenv bootargs $(bootargs_linux); mw.l f1010100 0020c000; usb reset; ext2load usb 0:1 $(loadaddr) /uImage; ext2load usb 0:1 0x01100000 /uInitrd; bootm $(loadaddr) 0x01100000
bootcmd_stock=setenv bootargs $(bootargs_stock); nand read.e $(loadaddr) $(kernel_addr) 0xA00000; bootm $(loadadr)
to_stock=setenv mainlineLinux no; setenv bootcmd \'run bootcmd_stock\'; saveenv; reset
to_linux=setenv mainlineLinux yes; setenv bootcmd \'run bootcmd_linux\'; saveenv; reset
bootcmd='run bootcmd_linux'
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
disaMvPnp=no
enaAutoRecovery=yes
kernel_addr=0x4640000
pcieTune=no
pcieTune1=no

Environment size: 2498/131068 bytes






Marvell>> setenv bootargs_linux 'console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=LABEL=rootfs loglevel=8 earlyprintk=serial'



Marvell>> setenv bootcmd_linux 'setenv bootargs $(bootargs_linux); mw.l f1010100 0020c000; usb reset; ext2load usb 0:1 $(loadaddr) /boot/uImage; ext2load usb 0:1 0x02100000 /boot/uInitrd; bootm $(loadaddr) 0x02100000'



Marvell>> printenv
bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
bootdelay=2
baudrate=115200
loads_echo=0
ipaddr=10.4.52.165
serverip=10.4.52.7
rootpath=/srv/ubuntu
netmask=255.255.255.0
nandEcc=1bit
MODEL_ID=AE03
PRODUCT_NAME=NSA-325v2
FEATURE_BIT=00
CONTRY_TYPE=FF
VENDOR_NAME=MitraStar Technology Corp.
run_diag=yes
console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root)
ethprime=egiga0
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
lcd0_enable=0
lcd0_params=640x480-16@60
ethaddr=00:50:43:00:02:02
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
image_multi=yes
ethact=egiga0
arcNumber=4495
bootargs_stock=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
bootcmd_stock=setenv bootargs $(bootargs_stock); nand read.e $(loadaddr) $(kernel_addr) 0xA00000; bootm $(loadadr)
to_stock=setenv mainlineLinux no; setenv bootcmd \'run bootcmd_stock\'; saveenv; reset
to_linux=setenv mainlineLinux yes; setenv bootcmd \'run bootcmd_linux\'; saveenv; reset
bootcmd='run bootcmd_linux'
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
disaMvPnp=no
enaAutoRecovery=yes
kernel_addr=0x4640000
pcieTune=no
pcieTune1=no
bootargs_linux=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=LABEL=rootfs loglevel=8 earlyprintk=serial
bootcmd_linux=setenv bootargs $(bootargs_linux); mw.l f1010100 0020c000; usb reset; ext2load usb 0:1 $(loadaddr) /boot/uImage; ext2load usb 0:1 0x02100000 /boot/uInitrd; bootm $(loadaddr) 0x02100000

Environment size: 2527/131068 bytes
Marvell>>boot
(Re)start USB...
USB:   scanning bus for devices... 3 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found

** Unable to read "/boot/uImage" from usb 0:1 **

** Unable to read "/boot/uInitrd" from usb 0:1 **
## Booting image at 02000000 ...
Bad Magic Number
Marvell>>

Regards.
Re: NSA325 - stock u-boot problem booting with Linux Kernel 4.13.5
October 14, 2017 06:12PM
dummy64,

> I'm sorry I didn't told you earlier that the first
> partition is a dedicated /boot partition.
> the rest of the system is located in the second
> partition.
> Both are ext2 partitions. I didn't moved any USB
> drives. I only put again the newer kernel files

I see :) that's the missing information.

Can you use 1 partition? There is no good reason to use 2 partitions on this box. Stock u-boot and my released u-boot should boot on USB Ext2/Ext3 partition. Unless you want to use stock u-boot and Ext4/f2fs/btrfs/XFS rootfs.

If you absolutely need 2 partition structure, then using the envs I posted above, you need:

1. your "boot" partition must be 1st partition on the disk,
2. and on that "boot" partition the root level there must be /boot folder and contains the 2 kernel files. So the files look like:

/boot/uImage
/boot/uInitrd
Note: /boot here is a folder, not parttition name.

-bodhi
===========================
Forum Wiki
bodhi's corner



Edited 1 time(s). Last edit at 10/14/2017 06:13PM by bodhi.
Author:

Your Email:


Subject:


Spam prevention:
Please, solve the mathematical question and enter the answer in the input field below. This is for blocking bots that try to post this form automatically.
Question: how much is 6 plus 21?
Message: