Possible to get Debian on a Medion NAS P89654 2x4 TB?
Posted by saschbaer
|
Possible to get Debian on a Medion NAS P89654 2x4 TB? November 01, 2017 03:31AM |
Registered: 6 years ago Posts: 24 |
Hello,
I own a Medion NAS with 2x4TB WD Harddisk Model WDC WD40EZRX-22SPEB0.
I studied the forum about flashing several NAS to use Debian on it, but I'm unsure if my NAS has the possibility to do it.
I have root access to my box and was able to install ipkg and other (so it can be used like an open stora.)
The kernel is based on HipServ Axentra, version 2.6.31.8 (so very old...:-/)
The mtd partition is
If you need more informations, do not hesitate to contact me and I will post more infos.
Regards from Germany
Saschbaer
I own a Medion NAS with 2x4TB WD Harddisk Model WDC WD40EZRX-22SPEB0.
I studied the forum about flashing several NAS to use Debian on it, but I'm unsure if my NAS has the possibility to do it.
I have root access to my box and was able to install ipkg and other (so it can be used like an open stora.)
The kernel is based on HipServ Axentra, version 2.6.31.8 (so very old...:-/)
Processor : Feroceon 88FR131 rev 1 (v5l) BogoMIPS : 999.42 Features : swp half thumb fastmult edsp CPU implementer : 0x56 CPU architecture: 5TE CPU variant : 0x2 CPU part : 0x131 CPU revision : 1 Hardware : Feroceon-KW Revision : 0000 Serial : 0000000000000000
The mtd partition is
dev: size erasesize name mtd0: 00100000 00020000 "u-boot" mtd1: 00600000 00020000 "uImage" mtd2: 0f900000 00020000 "rootfs"
If you need more informations, do not hesitate to contact me and I will post more infos.
Regards from Germany
Saschbaer
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 01, 2017 04:21PM |
Admin Registered: 13 years ago Posts: 18,576 |
saschbaer,
Yes, it is possible to run Debian on this box. It is a Kirkwood SoC like every other boxes I supported here. However, most likely, there are differences in hardwarre peripherals and GPIOs, so a new DTS for this box is needed, which can be based on existing DTS for other boxes. This might be easy, or hard, I'm not sure, until I see the boot log.
And also, you should get GPL source for this box from the manufacturer or from other public sources. Sometime, a few minor details can only be found by looking at the GPL source code. We can only find things such as GPIOs (to control hardware) from GPL source.
Do you have serial console connected? if yes, please post the entire serial console boot log here.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Quote
> Processor : Feroceon 88FR131 rev 1 (v5l)
> BogoMIPS : 999.42
> Features : swp half thumb fastmult edsp
> CPU implementer : 0x56
> CPU architecture: 5TE
> CPU variant : 0x2
> CPU part : 0x131
> CPU revision : 1
>
> Hardware : Feroceon-KW
> Revision : 0000
> Serial : 0000000000000000
Yes, it is possible to run Debian on this box. It is a Kirkwood SoC like every other boxes I supported here. However, most likely, there are differences in hardwarre peripherals and GPIOs, so a new DTS for this box is needed, which can be based on existing DTS for other boxes. This might be easy, or hard, I'm not sure, until I see the boot log.
And also, you should get GPL source for this box from the manufacturer or from other public sources. Sometime, a few minor details can only be found by looking at the GPL source code. We can only find things such as GPIOs (to control hardware) from GPL source.
Do you have serial console connected? if yes, please post the entire serial console boot log here.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 09, 2017 11:22AM |
Registered: 6 years ago Posts: 24 |
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: DB6702A-GMtech LE
U-Boot 1.1.4 (Jun 5 2013 - 10:49:39) Marvell version: 3.6.0
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00
Soc: 88F6702 A1 CPU running @ 1000Mhz L2 running @ 500Mhz
SysClock = 400Mhz , TClock = 166Mhz
DRAM (DDR2) CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
*** Warning - bad CRC or NAND, using default environment
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0 [PRIME]
Marvell>> printenv
baudrate=115200
loads_echo=0
ipaddr=10.4.52.165
serverip=10.4.52.7
rootpath=/srv/ubuntu
netmask=255.255.255.0
run_diag=yes
stdin=serial
stdout=serial
stderr=serial
console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0xff00000@0x1)
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
MALLOC_len=1
ethprime=egiga0
netbsd_en=no
vxworks_en=no
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
bootcmd=tftpboot 0x2000000 $(image_name); setenv bootargs $(console) $(bootargs
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/;
bootdelay=3
disaMvPnp=no
ethaddr=00:50:43:00:02:02
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
nandEcc=1bit
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
image_multi=yes
enaAutoRecovery=yes
pcieTune=no
ethact=egiga0
Environment size: 1367/131068 bytes
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 09, 2017 11:41AM |
Registered: 6 years ago Posts: 24 |
Sorry for answering so late, but it seems that i bricked or damaged the uboot...
i get this:
so what to do now?
i get this:
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: DB6702A-GMtech LE
U-Boot 1.1.4 (Jun 5 2013 - 10:49:39) Marvell version: 3.6.0
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00
Soc: 88F6702 A1 CPU running @ 1000Mhz L2 running @ 500Mhz
SysClock = 400Mhz , TClock = 166Mhz
DRAM (DDR2) CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
*** Warning - bad CRC or NAND, using default environment
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
egiga0 no link
Using egiga0 device
TFTP from server 10.4.52.7; our IP address is 10.4.52.165
Filename 'uImage'.
Load address: 0x2000000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
## Booting image at 02000000 ...
Bad Magic Number
Unknown command '<NULL>' - try 'help'
so what to do now?
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 09, 2017 04:08PM |
Admin Registered: 13 years ago Posts: 18,576 |
saschbaer,
This is a close cousin of the NSA310S and Pogo V4. We should be able to get a this running with new kernel. And then how complete it is will be depending on how much informtion you can find (i.e access to GPL source).
Yes, you have a corrupted NAND area where the envs are. But I hope it is not serious.
Look back to the printenv you did in serial console when you first boot up this box with it (before the corruption). Did you list the envs and keep the log of that?
1. Usually, you can just reenter them one by one at serial console and then save it. That will create a new copy with a good checksum. If the NAND sector is not really bad, just the checksum is bad, then it will be back to normal.
2. If the NAND sector is actually bad, then that's a more complicate issue. You need to use the good set of envs (which you enter manually at serial console prompt in number 1 above), boot all the way in to stock OS, or new Debian rootfs. And then we'll take a look to see how to proceed.
3. If the NAND sector is bad, one way to recover is trying to scrub it in serial console. Hopefully it will be back.
4. If there is no way to recover that NAND sector, then we'll need new u-boot for this box to completely fix it (ie. I do use a different NAND area for u-boot envs for Kirkwood boxes).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Quote
> ** MARVELL BOARD: DB6702A-GMtech LE
> Soc: 88F6702 A1 CPU running @ 1000Mhz L2 running @
> 500Mhz
> SysClock = 400Mhz , TClock = 166Mhz
This is a close cousin of the NSA310S and Pogo V4. We should be able to get a this running with new kernel. And then how complete it is will be depending on how much informtion you can find (i.e access to GPL source).
Quote
> *** Warning - bad CRC or NAND, using default
> environment
>
Yes, you have a corrupted NAND area where the envs are. But I hope it is not serious.
Look back to the printenv you did in serial console when you first boot up this box with it (before the corruption). Did you list the envs and keep the log of that?
1. Usually, you can just reenter them one by one at serial console and then save it. That will create a new copy with a good checksum. If the NAND sector is not really bad, just the checksum is bad, then it will be back to normal.
2. If the NAND sector is actually bad, then that's a more complicate issue. You need to use the good set of envs (which you enter manually at serial console prompt in number 1 above), boot all the way in to stock OS, or new Debian rootfs. And then we'll take a look to see how to proceed.
3. If the NAND sector is bad, one way to recover is trying to scrub it in serial console. Hopefully it will be back.
4. If there is no way to recover that NAND sector, then we'll need new u-boot for this box to completely fix it (ie. I do use a different NAND area for u-boot envs for Kirkwood boxes).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 10, 2017 03:17AM |
Registered: 6 years ago Posts: 24 |
Look back to the printenv you did in serial console when you first boot up this box with it (before the corruption). Did you list the envs and keep the log of that?
Im not sure what you mean with list and log... I just did the printenv which is listed in here. I have to admit that I didn't save the original env list and log :-(
I remember that in the fw_env.conf file there was just one line which autoconfigs the box with IP and so...
1. Usually, you can just reenter them one by one at serial console and then save it. That will create a new copy with a good checksum. If the NAND sector is not really bad, just the checksum is bad, then it will be back to normal.
You really mean just copy paste the printenv line by line? But how to save then?
Ànother question is where is the Definition of my jbod stored - in one of the uboot-files?
I tried to attach them on my ubuntu Laptop but just get the info that theres a GPT Format and I cannot re-assemble them with mdadm...
2. If the NAND sector is actually bad, then that's a more complicate issue. You need to use the good set of envs (which you enter manually at serial console prompt in number 1 above), boot all the way in to stock OS, or new Debian rootfs. And then we'll take a look to see how to proceed.Do I Need to prepare an USB stick for that and boot from it?
3. If the NAND sector is bad, one way to recover is trying to scrub it in serial console. Hopefully it will be back.How to do?
4. If there is no way to recover that NAND sector, then we'll need new u-boot for this box to completely fix it (ie. I do use a different NAND area for u-boot envs for Kirkwood boxes).
Okay, so how will I proceed the best way - as you numbered?
Edited 1 time(s). Last edit at 11/10/2017 03:36AM by saschbaer.
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 10, 2017 03:45AM |
Admin Registered: 13 years ago Posts: 18,576 |
saschbaer,
> Im not sure what you mean with list and log... I
> just did the printenv which is listed in here.
What you listed were the u-boot internal envs. That's what u-boot uses when encountered a bad CRC checksum, or a bad NAND sector where the envs are stored.
What actually stored in that NAND sector is the envs that used for booting. Thus, you could not boot because the internal envs are just some default values, not good enough for booting stock OS.
What I meant by listing and log: normally, the first thing we want to do after we connect serial console or boot into stock OS, is to list the envs, and then keep a log of that for recovery purpose. Without that log, you can't restore a good set of envs to boot into stock OS, now that the current envs NAND area is bad.
> 1. Usually, you can just reenter them one
> by one at serial console and then save it. That
> will create a new copy with a good checksum. If
> the NAND sector is not really bad, just the
> checksum is bad, then it will be back to normal.
> [/code]
>
>
> You really mean just copy paste the printenv line
> by line? But how to save then?
Yes, line-by-line. Once you can boot into stock OS then worry about saving them.
At this point, number 1 what you need to do to recover. After that, you will have many options.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> Im not sure what you mean with list and log... I
> just did the printenv which is listed in here.
What you listed were the u-boot internal envs. That's what u-boot uses when encountered a bad CRC checksum, or a bad NAND sector where the envs are stored.
What actually stored in that NAND sector is the envs that used for booting. Thus, you could not boot because the internal envs are just some default values, not good enough for booting stock OS.
## Booting image at 02000000 ... Bad Magic Number
What I meant by listing and log: normally, the first thing we want to do after we connect serial console or boot into stock OS, is to list the envs, and then keep a log of that for recovery purpose. Without that log, you can't restore a good set of envs to boot into stock OS, now that the current envs NAND area is bad.
> 1. Usually, you can just reenter them one
> by one at serial console and then save it. That
> will create a new copy with a good checksum. If
> the NAND sector is not really bad, just the
> checksum is bad, then it will be back to normal.
> [/code]
>
>
> You really mean just copy paste the printenv line
> by line? But how to save then?
Yes, line-by-line. Once you can boot into stock OS then worry about saving them.
At this point, number 1 what you need to do to recover. After that, you will have many options.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 10, 2017 03:56AM |
Registered: 6 years ago Posts: 24 |
What I meant by listing and log: normally, the first thing we want to do after we connect serial console or boot into stock OS, is to list the envs, and then keep a log of that for recovery purpose. Without that log, you can't restore a good set of envs to boot into stock OS, now that the current envs NAND area is bad.
As I wrote, I have to admit I haven't saved the original printenv log :-(
So how to proceed now?
I remember I entered a set of envs for using nc without Serial terminal.
With that I changed the Server and Client IP and entered the NC commands as posted.
Any possibility to undo that action?
Edited 1 time(s). Last edit at 11/10/2017 04:11AM by saschbaer.
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 10, 2017 04:24AM |
Admin Registered: 13 years ago Posts: 18,576 |
1. Google for this box name, hopefully that in some forum, someone has the same box in working order, and you can ask for a listing of the current envs.
2. If 1 fails, contact the manufacturer or visit their website to find the recovery Firmware.
3. If 1 and 2 fail (I will not be surpised because either the box might be too old, or nobody has hacked it), come back and we'll try the UART booting method using kwboot to see if you can boot with one of my released u-boots. And then go from there.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
2. If 1 fails, contact the manufacturer or visit their website to find the recovery Firmware.
3. If 1 and 2 fail (I will not be surpised because either the box might be too old, or nobody has hacked it), come back and we'll try the UART booting method using kwboot to see if you can boot with one of my released u-boots. And then go from there.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 10, 2017 04:32AM |
Registered: 6 years ago Posts: 24 |
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 10, 2017 04:35AM |
Admin Registered: 13 years ago Posts: 18,576 |
saschbaer Wrote:
-------------------------------------------------------
> I remember I entered a set of envs for using nc
> without Serial terminal.
> With that I changed the Server and Client IP and
> entered the NC commands as posted.
> Any possibility to undo that action?
No way to undo that without knowing what a good set of envs is supposed to be.
And netconsole does not work in stock u-boot (I have never seen a stock u-boot that supports netconsole). So you don't want do that for any box that still had stock u-boot.
Anyhow, that must have been why the envs are corrupted (what being entered was not what stock u-boot expected, as far as the checksum is concerned). So in a way, that is good news! that told us the CRC checksum is wrong, not a bad NAND sector.
By the way, you should have posted this fact when you see the booting problem yesterday.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> I remember I entered a set of envs for using nc
> without Serial terminal.
> With that I changed the Server and Client IP and
> entered the NC commands as posted.
> Any possibility to undo that action?
No way to undo that without knowing what a good set of envs is supposed to be.
And netconsole does not work in stock u-boot (I have never seen a stock u-boot that supports netconsole). So you don't want do that for any box that still had stock u-boot.
Anyhow, that must have been why the envs are corrupted (what being entered was not what stock u-boot expected, as far as the checksum is concerned). So in a way, that is good news! that told us the CRC checksum is wrong, not a bad NAND sector.
By the way, you should have posted this fact when you see the booting problem yesterday.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 10, 2017 03:58PM |
Admin Registered: 13 years ago Posts: 18,576 |
saschbaer,
Dowload the NSA310S u-boot:
https://forum.doozan.com/read.php?3,12381
Read this UART booting mentioned in that thread:
You will need another Linux box to connect serial console, Windows PC cannot run kwboot.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Dowload the NSA310S u-boot:
https://forum.doozan.com/read.php?3,12381
Read this UART booting mentioned in that thread:
Quote
UART Booting: If possible, try to test this boot image with UART booting before flashing to NAND. See davygravy's UART booting using kwboot instruction here in this thread. The latest u-boot image released here should be used for UART booting, if your box is the type that supports it (these do not: Dockstar, Pogo E02, iConnect).
You will need another Linux box to connect serial console, Windows PC cannot run kwboot.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 11, 2017 03:44AM |
Registered: 6 years ago Posts: 24 |
Morning...
I got kwboot from my ubuntu distrib and downloaded the file.
But if I start to use kwboot, I get special characters like this:
Execute kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.nsa310s.mtd0.kwb
Output of Minicom:
baudrate is 115200 on minicom
I did also a md md ff00003c, but got zeros back...
What to try else?
I got kwboot from my ubuntu distrib and downloaded the file.
But if I start to use kwboot, I get special characters like this:
Execute kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.nsa310s.mtd0.kwb
Output of Minicom:
* MARVLL BARD: DB702A-GMtech LE
U-Boot 1.1.4 un 5 213 - 10:49:39) Marvell ersi3.6.0
UBoot code: 00600000 > 0067FFF0 BSS: -> 006CB00
Sc: 88F672 A1 C runni @ 1000hz L2 rnning @ 500Mhz
ysClock 400Mh , TClok = 166Mhz
DAM (DDR) CAS Latcy = 5tRP = 5 tRAS = 18 tRCD=6
DRAM C[0] bae 0x0000000 ize 256M
DRAM Total sze 256M 16bit dth
Addresses 8M - 0M re saved for the U-Boot usage.
*** Warnin-badCRC oNAN,sinfau envroment MB
Flsh: kB
CP: MrvFroo v
remibled
llisl
U md
Hit any key op ao: 3 0Marvell>> "3DUwDUfwDU�3w�Dw�"3Dw�"�"3�"3Uf"DUw�"3
you see there characters are missing or getting strange while kwboot tries to submit the file.
baudrate is 115200 on minicom
I did also a md md ff00003c, but got zeros back...
What to try else?
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 11, 2017 04:33AM |
Admin Registered: 13 years ago Posts: 18,576 |
saschbaer,
This indicated that kwboot did not handshake with box. So it did not run. Stock u-boot has started and running.
This is the correct command:
And minicom should not be run. Only kwboot command should be executed. kwboot is the serial console while you are running it.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 11/11/2017 04:36AM by bodhi.
Quote
* MARVLL BARD: DB702A-GMtech LE
U-Boot 1.1.4 un 5 213 - 10:49:39) Marvell ersi3.6.0
UBoot code: 00600000 > 0067FFF0 BSS: -> 006CB00
Sc: 88F672 A1 C runni @ 1000hz L2 rnning @ 500Mhz
ysClock 400Mh , TClok = 166Mhz
DAM (DDR) CAS Latcy = 5tRP = 5 tRAS = 18 tRCD=6
DRAM C[0] bae 0x0000000 ize 256M
DRAM Total sze 256M 16bit dth
Addresses 8M - 0M re saved for the U-Boot usage.
*** Warnin-badCRC oNAN,sinfau envroment MB
Flsh: kB
CP: MrvFroo v
remibled
llisl
U md
Hit any key op ao: 3 0Marvell>> "3DUwDUfwDU�3w�Dw�"3Dw�"�"3�"3Uf"DUw�"3
This indicated that kwboot did not handshake with box. So it did not run. Stock u-boot has started and running.
This is the correct command:
kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.nsa310s.mtd0.kwb -p
And minicom should not be run. Only kwboot command should be executed. kwboot is the serial console while you are running it.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 11/11/2017 04:36AM by bodhi.
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 11, 2017 04:49AM |
Registered: 6 years ago Posts: 24 |
Hello again...
I closed minicom, started your command (with and without -p)
But theres only the fast spinning character, no feedback from the nas...
I also checked TXD/RXD, and if i changed and started the spinning character went really slow then.
as i changed back TXD/RXD its running fast again...
any idea?
I closed minicom, started your command (with and without -p)
But theres only the fast spinning character, no feedback from the nas...
I also checked TXD/RXD, and if i changed and started the spinning character went really slow then.
as i changed back TXD/RXD its running fast again...
any idea?
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 11, 2017 05:19AM |
Admin Registered: 13 years ago Posts: 18,576 |
saschbaer,
You already have the correct RXD and TXD connection when you used minicom, and could interrupt stock u-boot at countdown. And when kwboot slows down, it senses some character at the port that it can't recognize. So it is not RXD/TXD.
I think the bad news is most likely your box does not support UART booting (same as some of the Kirkwood boxes such as Dockstar, Pogo E02,...).
However, you could keep trying to control-C and then restart kwboot for 10, 20 times (without recycling power) to see if it helps.
And also try running kwboot while gently pressing down on the TXD and RXD wire connectors (at the board serial header).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
You already have the correct RXD and TXD connection when you used minicom, and could interrupt stock u-boot at countdown. And when kwboot slows down, it senses some character at the port that it can't recognize. So it is not RXD/TXD.
I think the bad news is most likely your box does not support UART booting (same as some of the Kirkwood boxes such as Dockstar, Pogo E02,...).
However, you could keep trying to control-C and then restart kwboot for 10, 20 times (without recycling power) to see if it helps.
And also try running kwboot while gently pressing down on the TXD and RXD wire connectors (at the board serial header).
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 11, 2017 05:53AM |
Registered: 6 years ago Posts: 24 |
bodhi,
may you have a look here
https://forum.doozan.com/read.php?2,32877,33022,quote=1
helge seems to have nanddumped the original md0,1,2 from a Medion Nas.
May it be an idea testing if those uboot dumps can be flashed on my nas?
seems the same confuguration just that he has a 2x2 TB and me 2x4 TB.
What do you think, and if you agree, how do I get the dumps flashed then?
may you have a look here
https://forum.doozan.com/read.php?2,32877,33022,quote=1
helge seems to have nanddumped the original md0,1,2 from a Medion Nas.
May it be an idea testing if those uboot dumps can be flashed on my nas?
seems the same confuguration just that he has a 2x2 TB and me 2x4 TB.
What do you think, and if you agree, how do I get the dumps flashed then?
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 11, 2017 06:14AM |
Admin Registered: 13 years ago Posts: 18,576 |
========= helge's log
It's a different Medion NAS model, but u-boot does look identical.
But you don't need to reflash u-boot. Just use helge's posted envs to restore your box to a a good default set. See the envs text file attached in the 1st post: https://forum.doozan.com/read.php?2,32877,32877#msg-32877
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
** MARVELL BOARD: DB6702A-GMtech LE U-Boot 1.1.4 (Jun 5 2013 - 10:49:39) Marvell version: 3.6.0 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00 Soc: 88F6702 A1 CPU running @ 1000Mhz L2 running @ 500Mhz SysClock = 400Mhz , TClock = 166Mhz DRAM (DDR2) CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:256 MB Flash: 0 kB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 Net: egiga0 [PRIME] Hit any key to stop autoboot: 3 2 1 0
It's a different Medion NAS model, but u-boot does look identical.
But you don't need to reflash u-boot. Just use helge's posted envs to restore your box to a a good default set. See the envs text file attached in the 1st post: https://forum.doozan.com/read.php?2,32877,32877#msg-32877
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 11, 2017 11:02AM |
Registered: 6 years ago Posts: 24 |
Happy News bodhi...
with the help of helge i managed to set the NAS back to factory setting, reflashing the origin sys AND kept my data *bigsighofrelief*
So, we may can start to manage Debian on the NAS.
So ..what do we need at first now?
It would be very nice if you can assist :-D and many many thanks for your help up to this point.
Regards
Saschbaer
with the help of helge i managed to set the NAS back to factory setting, reflashing the origin sys AND kept my data *bigsighofrelief*
So, we may can start to manage Debian on the NAS.
So ..what do we need at first now?
It would be very nice if you can assist :-D and many many thanks for your help up to this point.
Regards
Saschbaer
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 11, 2017 03:57PM |
Admin Registered: 13 years ago Posts: 18,576 |
saschbaer,
Cool :)
Now you can read helge's thread to see how the new Debian rootfs can be booted on USB.
1. Create the Debian rootfs on USB first:
https://forum.doozan.com/read.php?2,12096
2. Verify your u-boot can boot USB:
Power up interrupt serial console and
3. Repeat what helge did in setting up the envs. You might want to list the setenv commands that you will execute here, so I can help look over for any error or things that we want to avoid doing at serial console.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Cool :)
Now you can read helge's thread to see how the new Debian rootfs can be booted on USB.
1. Create the Debian rootfs on USB first:
https://forum.doozan.com/read.php?2,12096
Quote
Updated 24 Jul 2017:
Basic Debian stretch Kirkwood rootfs for most Kirwood plugs:
- tarball size: 188M
- install size: 488M
- The init system used in this rootfs is sysvinit . To boot with systemd, see note 2 below.
- Installed packages: nano, avahi, ntp, busybox-syslogd (log to RAM), htop, isc-dhcp-client, dialog, bzip2, nfs server/client, iperf, ethtool, sysvinit-core, sysvinit, and sysvinit-utils.
- see LED controls in /etc/rc.local, and /etc/init.d/halt
- see some useful aliases in /root/.profile
- root password: root
Download at Dropbox:
Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2
md5:
bf3d29569943875df348fb5ca03b348c
sha256:
4ed5714fdb123cdb40e973f3d0754e91cd199b75a9874018f2b5dc9cfa8ae8bb
And remember to check the hash of what you download, as always.
2. Verify your u-boot can boot USB:
Power up interrupt serial console and
usb start
3. Repeat what helge did in setting up the envs. You might want to list the setenv commands that you will execute here, so I can help look over for any error or things that we want to avoid doing at serial console.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 12, 2017 06:13AM |
Registered: 6 years ago Posts: 24 |
Well I created the USB Stick (Intenso 32 GB) as root with ext3, extracted the tar...
i choosed kirkwood320s, did the build on my Ubuntu x64 laptop,
I entered that:
and the bootlog after that made:
when I boot up with plugged USB stick i get this:
So Axentra recognizes the stick...u-boot does not it seems.
May you can help?
Regards
Saschbaer
i choosed kirkwood320s, did the build on my Ubuntu x64 laptop,
root@SaschSamsung:/media/sdd1/boot# mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-4.12.1-kirkwood-tld-1 -d zImage.fdt uImage Image Name: Linux-4.12.1-kirkwood-tld-1 Created: Sun Nov 12 12:43:05 2017 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3834820 Bytes = 3744.94 kB = 3.66 MB Load Address: 00008000 Entry Point: 00008000 root@SaschSamsung:/media/sdd1/boot# syncand then brought it to my Medion.
I entered that:
setenv mainlineLinux yes setenv set_bootargs 'setenv bootargs console=ttyS0,115200' setenv usb_load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' setenv usb_load_uinitrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd' setenv usb_boot 'usb start; run set_bootargs; run usb_load_uimage; run usb_load_uinitrd; bootm 0x800000 0x1100000' run usb_boot
and the bootlog after that made:
USB: scanning bus for devices... 1 USB Device(s) found Waiting for storage device(s) to settle before scanning... 0 Storage Device(s) foundUSB part made:
print_part of 0
## Unknown partition table
print_part of 1
## Unknown partition table
print_part of 2
## Unknown partition table
print_part of 3
## Unknown partition table
print_part of 4
## Unknown partition table
when I boot up with plugged USB stick i get this:
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: DB6702A-GMtech LE
U-Boot 1.1.4 (Jun 5 2013 - 10:49:39) Marvell version: 3.6.0
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00
Soc: 88F6702 A1 CPU running @ 1000Mhz L2 running @ 500Mhz
SysClock = 400Mhz , TClock = 166Mhz
DRAM (DDR2) CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x100000, size 0x400000
Reading data from 0x4ff800 -- 100% complete.
4194304 bytes read: OK
## Booting image at 00800000 ...
Image Name: Linux-2.6.31.8
Created: 2014-02-19 22:12:57 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3163392 Bytes = 3 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Linux version 2.6.31.8 (mostafah@es5x86.axentra.com) (gcc version 4.3.2 (sdk3.34
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 65024
Kernel command line: console=ttyS0,115200 ubi.mtd=2,2048 root=ubi0:rootfs rootfc
PID hash table entries: 1024 (order: 10, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 247680KB available (4784K code, 283K data, 720K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Console: colour dummy device 80x30
Calibrating delay loop... 999.42 BogoMIPS (lpj=4997120)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
[BlueDBG] mvBoardIdGet()= 0x<NULL>
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 256MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
PEX1_MEM ....no such
PEX1_IO ....no such
INTER_REGS ....base f1000000, size 1MB
NFLASH_CS ....base fa000000, size 2MB
SPI_CS ....base f4000000, size 16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size 2MB
Marvell Development Board (LSP Version KW_LSP_5.1.3_patch30)-- DB6702A-GMtechE
Detected Tclk 166666667 and SysClk 400000000
MV Buttons Device Load
btns_init_data - DB 6702A
btns_init_data - Number of configured buttons: 2
Marvell USB EHCI Host controller #0: c8040740
PEX0 interface detected Link X1
PCI: bus0: Fast back to back transfers disabled
mvPexLocalBusNumSet: ERR. Invalid PEX interface 1
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
RTC has been updated!!!
rtc mv_rtc: rtc core: registered kw-rtc as rtc0
RTC registered
cpufreq: Init kirkwood cpufreq driver
XOR registered 4 channels
XOR 2nd invalidate WA enabled
cesadev_init(c000e0bc)
mvCesaInit: sessions=640, queue=64, pSram=f0000000
Warning: TS unit is powered off.
MV Buttons Driver Load
SGI XFS with security attributes, large block/inode numbers, no debug enabled
msgmni has been set to 484
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for stdrng (krng)
alg: No test for hmac(digest_null) (hmac(digest_null-generic))
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered (default)
Initializing ths8200_init
Initializing dove_adi9889_init
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012100 (irq = 34) is a 16550A
console [ttyS0] enabled
Integrated Sata device found
IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
Loading Marvell Ethernet Driver:
o Cached descriptors in DRAM
o DRAM SW cache-coherency
o 1 Giga ports supported
o Single RX Queue support - ETH_DEF_RXQ=0
o Single TX Queue support - ETH_DEF_TXQ=0
o TCP segmentation offload (TSO) supported
o Large Receive offload (LRO) supported
o Receive checksum offload supported
o Transmit checksum offload supported
o Network Fast Processing (Routing) supported - (Disabled)
o Driver ERROR statistics enabled
o Proc tool API enabled
o SKB Reuse supported - (Disabled)
o SKB Recycle supported - (Disabled)
o Rx descripors: q0=128
o Tx descripors: q0=532
o Loading network interface(s):
o register under mv88fx_eth platform
o eth0, ifindex = 2, GbE port = 0
mvFpRuleDb (c8238000): 2048 entries, 8192 bytes
Counter=0, opIdx=6, overhead=16
Counter=1, opIdx=2, overhead=0
Counter=2, opIdx=1, overhead=18
Counter=3, opIdx=2, overhead=0
Intel(R) PRO/1000 Network Driver - version 7.3.21-k3-NAPI
Copyright (c) 1999-2006 Intel Corporation.
e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
e1000e: Copyright (c) 1999-2008 Intel Corporation.
e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
Using Hamming 1-bit ECC for NAND device
NAND device: Manufacturer ID: 0xc8, Chip ID: 0xda (Zentel NAND 256MiB 3,3V 8-bi)
Scanning device for bad blocks
Using static partition definition
Creating 3 MTD partitions on "nand_mtd":
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000700000 : "uImage"
0x000000700000-0x000010000000 : "rootfs"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: attached mtd2 to ubi0
UBI: MTD device name: "rootfs"
UBI: MTD device size: 249 MiB
UBI: number of good PEBs: 1992
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 1992
UBI: number of PEBs reserved for bad PEB handling: 38
UBI: max/mean erase counter: 3/0
UBI: image sequence number: 0
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
UBI: background thread "ubi_bgt0d" started, PID 460
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
xhci_hcd 0000:00:01.0: xHCI Host Controller
xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2
xhci_hcd 0000:00:01.0: irq 9, io mem 0xe0000000
xhci_hcd 0000:00:01.0: Failed to enable MSI-X
xhci_hcd 0000:00:01.0: failed to allocate MSI entry
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
xhci_hcd 0000:00:01.0: xHCI Host Controller
xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
drivers/rtc/hctosys.c: unable to open rtc device (rtc)
Freeing init memory: 720K
Reset button not pressed
Proceeding normally.
UBIFS: recovery needed
usb 1-1: new high-speed USB device number 2 using ehci_marvell
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size: 239857664 bytes (234236 KiB, 228 MiB, 1889 LEBs)
UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: zlib
UBIFS: reserved for root: 0 bytes (0 KiB)
scsi2 : usb-storage 1-1:1.0
INIT: version 2.86 booting
Welcome to HipServ
Press 'I' to enter interactive startup.
System clock set to hardware clock.
Setting clock (utc): Sun Nov 12 13:08:26 CET 2017 [ OK ]
Starting udev: [ OK ]
Setting hostname orionnas: [ OK ]
Setting up Logical Volume Management: No volume groups found
[ OK ]
Checking filesystems
Checking all file systems.
[ OK ]
Mounting local filesystems: mount: sysfs already mounted or /sys busy
mount: according to mtab, /sys is already mounted on /sys
[FAILED]
Enabling /etc/fstab swaps: [ OK ]
INIT: Entering runlevel: 3
Entering non-interactive startup
HipServ startup:Alarm cleared.
[FAILED]
Starting medion-lifecycle:[ OK ]
Starting reset: [ OK ]
Bringing up loopback interface: [ OK ]
Bringing up interface eth0:
Determining IP information for eth0... done.
[ OK ]
check_igd.pl: no process killed
[ OK ] igd-daemon:[ OK ]
Starting system logger: [ OK ]
Starting kernel logger: [ OK ]
Starting locator:[ OK ]
Starting system message bus: [ OK ]
Starting sshd: [ OK ]
Starting cups: [ OK ]
Starting xinetd: [ OK ]
Starting vsftpd for vsftpd: [ OK ]
Starting backupagent: [ OK ]
Starting httpd: [ OK ]
Starting appserver: [ OK ]
Starting crond: [ OK ]
Starting Netatalk services:
Starting cnid_metad:[ OK ]
Starting afpd:[ OK ]
Starting SMB services: [ OK ]
Starting NMB services: [ OK ]
Starting OEone System Proxy: SPD starting....log level=1, uid=0
[ OK ]
Starting Avahi daemon... [ OK ]
0
Starting DAAP server: [ OK ]
Starting mynetworkd:[ OK ]
HipServ - Checking if RAID needs to be rebuilt
Starting RAID monitor
1889
HipServ - Updating RAID lights
HipServ - Bringing up iptables
HipServ - Updating date...
success
HipServ - Enabling swap
*** WARNING: Could not start swapfile ***
HipServ - Cleaning USB mountpoints
HipServ - Mounting USB devices
tntfs: module license 'Commercial. For support email ntfs-support@tuxera.com.' .
Disabling lock debugging due to kernel taint
HipServ - Checking for FTPS certificate
HipServ - Found vsftpd key file
HipServ - Ensuring that table structures are up-to-date
HipServ - Checking for updates...
success
HipServ - boot complete
Starting spindownd.init: [ OK ]
Starting webmin: [FAILED]
So Axentra recognizes the stick...u-boot does not it seems.
May you can help?
Regards
Saschbaer
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 12, 2017 05:19PM |
Admin Registered: 13 years ago Posts: 18,576 |
Indeed, the USB partition is not recognized
Have you tried a different USB flash drive?
I have not check helge posts to see if I remember anything we need to do that is out of the ordinary. Yould could read that thread to see if you can spot anything special.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
USB: scanning bus for devices... 1 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
0 Storage Device(s) found
USB part made:
print_part of 0
## Unknown partition table
print_part of 1
## Unknown partition table
print_part of 2
## Unknown partition table
print_part of 3
## Unknown partition table
print_part of 4
## Unknown partition table
Have you tried a different USB flash drive?
I have not check helge posts to see if I remember anything we need to do that is out of the ordinary. Yould could read that thread to see if you can spot anything special.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 15, 2017 04:12PM |
Registered: 7 years ago Posts: 27 |
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 18, 2017 01:59AM |
Registered: 6 years ago Posts: 24 |
Hi,
after a few try and errors (and reflashing) I noticed something in another forum:
if you gpart an usb stick with ext2 name it boot and another ext4 name it rootfs the stick will be recognized correctly.
also I found out that maybe the NAS NSA325 seems to have the same config as my Medion P89654.
Maybe i should try to get the boot parts onto boot partition and the rest in rootfs?
Do i also have to adapt then the zImage file?
Or shall I reflash with a newer uBoot and then continue with the stick?
I found the manual in here
https://micha.stoecker.me/p/DNVpwG47
Regards
Saschbaer
after a few try and errors (and reflashing) I noticed something in another forum:
if you gpart an usb stick with ext2 name it boot and another ext4 name it rootfs the stick will be recognized correctly.
also I found out that maybe the NAS NSA325 seems to have the same config as my Medion P89654.
Maybe i should try to get the boot parts onto boot partition and the rest in rootfs?
Do i also have to adapt then the zImage file?
Or shall I reflash with a newer uBoot and then continue with the stick?
I found the manual in here
https://micha.stoecker.me/p/DNVpwG47
Regards
Saschbaer
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 18, 2017 04:18AM |
Admin Registered: 13 years ago Posts: 18,576 |
saschbaer,
> after a few try and errors (and reflashing) I
> noticed something in another forum:
> if you gpart an usb stick with ext2 name it boot
> and another ext4 name it rootfs the stick will be
> recognized correctly.
It is unecessary to have 2 partitions. Use one partition type Ext3 or Ext2.
>
> also I found out that maybe the NAS NSA325 seems
> to have the same config as my Medion P89654.
>
That's is wrong information. Medion P89654 uses 88F6702 SoC, which is the same as the Pogo V4 or NSA310S/320S.
> Maybe i should try to get the boot parts onto boot
> partition and the rest in rootfs?
Negative. You are going to a wrong direction there.
What you should do is figure out why this error occurred:
This bootlog indicated that the USB is supported (it was scanning). And somehow the partition table is unrecognized on this USB drive. So there is no storage drive.
So do this test. Power up, interrupt serial console and
If somehow this u-boot does not support Ext3 (I'd doubt this is the case), then just recreate the rootfs and use a single Ext2 partition will work.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> after a few try and errors (and reflashing) I
> noticed something in another forum:
> if you gpart an usb stick with ext2 name it boot
> and another ext4 name it rootfs the stick will be
> recognized correctly.
It is unecessary to have 2 partitions. Use one partition type Ext3 or Ext2.
>
> also I found out that maybe the NAS NSA325 seems
> to have the same config as my Medion P89654.
>
That's is wrong information. Medion P89654 uses 88F6702 SoC, which is the same as the Pogo V4 or NSA310S/320S.
Quote
U-Boot 1.1.4 (Jun 5 2013 - 10:49:39) Marvell version: 3.6.0
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00
Soc: 88F6702 A1 CPU running @ 1000Mhz L2 running @ 500Mhz
SysClock = 400Mhz , TClock = 166Mhz
> Maybe i should try to get the boot parts onto boot
> partition and the rest in rootfs?
Negative. You are going to a wrong direction there.
What you should do is figure out why this error occurred:
Quote
USB: scanning bus for devices... 1 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
0 Storage Device(s) found
USB part made:
print_part of 0
## Unknown partition table
print_part of 1
## Unknown partition table
print_part of 2
## Unknown partition table
print_part of 3
## Unknown partition table
print_part of 4
## Unknown partition table
This bootlog indicated that the USB is supported (it was scanning). And somehow the partition table is unrecognized on this USB drive. So there is no storage drive.
So do this test. Power up, interrupt serial console and
usb start usb part ext2ls usb 0:1 /bootIf you can list the content of the /boot folder on the rootfs at u-boot prompt, then the partition is good. If not, then the partition is bad (or unrecognized).
If somehow this u-boot does not support Ext3 (I'd doubt this is the case), then just recreate the rootfs and use a single Ext2 partition will work.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 18, 2017 08:38AM |
Registered: 6 years ago Posts: 24 |
OK. formatted with ext2, created rootfs, made the dts with kirkwoodnsa320s
uBoot recognized the stick and shows
but when I try to boot...
Regards
saschbaer
uBoot recognized the stick and shows
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
usb part
print_part of 0
Partition Map for USB device 0 -- Partition Type: DOS
Partition Start Sector Num Sectors Type
1 2048 62408704 83
print_part of 1
## Unknown partition table
print_part of 2
## Unknown partition table
print_part of 3
## Unknown partition table
print_part of 4
## Unknown partition table
ext2ls usb 0:1 /boot
<DIR> 4096 .
<DIR> 4096 ..
153501 config-4.12.1-kirkwood-tld-1
3821528 vmlinuz-4.12.1-kirkwood-tld-1
7245632 initrd.img-4.12.1-kirkwood-tld-1
7245696 uInitrd
8435004 linux-headers-4.12.1-kirkwood-tld-1_1.0_armel.deb
<DIR> 4096 dts
3821528 zImage-4.12.1-kirkwood-tld-1
3834884 uImage
2504031 System.map-4.12.1-kirkwood-tld-1
3834820 zImage.fdt
3821592 uImage.orig
but when I try to boot...
Marvell>> run usb_boot (Re)start USB... USB: scanning bus for devices... 1 USB Device(s) found Waiting for storage device(s) to settle before scanning... 0 Storage Device(s) found ** Bad partition 1 ** ** Bad partition 1 ** ## Booting image at 00800000 ... Bad Magic NumberIt seems that when I reset it, the partition won't be recognized again until I reset the NAS...strange...
Regards
saschbaer
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 18, 2017 04:28PM |
Admin Registered: 13 years ago Posts: 18,576 |
saschbaer,
Very good. It means that Ext3 or Ext2 will work. And there is nothing wrong with your USB partition.
It seems stock u-boot is messed up in reinitializing the USB drive. The 2nd "usb start" caused problem.
Try running it step by step
Power up, interrupt serial console and:
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Very good. It means that Ext3 or Ext2 will work. And there is nothing wrong with your USB partition.
It seems stock u-boot is messed up in reinitializing the USB drive. The 2nd "usb start" caused problem.
Try running it step by step
Power up, interrupt serial console and:
setenv mainlineLinux yes setenv set_bootargs 'setenv bootargs console=ttyS0,115200' setenv usb_load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' setenv usb_load_uinitrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd' run set_bootargs usb start usb part run usb_load_uimage run usb_load_uinitrd bootm 0x800000 0x1100000
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 18, 2017 05:00PM |
Registered: 6 years ago Posts: 24 |
okay...
Marvell>> setenv mainlineLinux yes
Marvell>> setenv set_bootargs 'setenv bootargs console=ttyS0,115200'
Marvell>> setenv usb_load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
Marvell>> setenv usb_load_uinitrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd'
Marvell>> run set_bootargs
Marvell>> usb start
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
Marvell>> usb part
print_part of 0
Partition Map for USB device 0 -- Partition Type: DOS
Partition Start Sector Num Sectors Type
1 2048 62408704 83
print_part of 1
## Unknown partition table
print_part of 2
## Unknown partition table
print_part of 3
## Unknown partition table
print_part of 4
## Unknown partition table
Marvell>> run usb_load_uimage
....
.
......
............
.........................
...................................................
................................................................................
................................................................................
3834884 bytes read
Marvell>> run usb_load_uinitrd
....
.
......
............
.........................
...................................................
................................................................................
................................................................................
....
................................................................................
7245696 bytes read
Marvell>> bootm 0x800000 0x1100000
## Booting image at 00800000 ...
Image Name: Linux-4.12.1-kirkwood-tld-1
Created: 2017-11-18 13:59:37 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3834820 Bytes = 3.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
Image Name: initramfs-4.12.1-kirkwood-tld-1
Created: 2017-07-24 0:18:23 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 7245632 Bytes = 6.9 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
and then nothing more...
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 18, 2017 05:13PM |
Admin Registered: 13 years ago Posts: 18,576 |
saschbaer,
Cool! so that was the problem with USB on this stock u-boot all along :) this u-boot is quite old.
Let's try with earlyprink:
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Cool! so that was the problem with USB on this stock u-boot all along :) this u-boot is quite old.
Let's try with earlyprink:
setenv mainlineLinux yes setenv set_bootargs 'setenv bootargs console=ttyS0,115200 earlyprintk=serial' setenv usb_load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' setenv usb_load_uinitrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd' run set_bootargs usb start usb part run usb_load_uimage run usb_load_uinitrd bootm 0x800000 0x1100000
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 18, 2017 06:35PM |
Registered: 6 years ago Posts: 24 |
