Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 18, 2017 07:41PM |
Admin Registered: 13 years ago Posts: 18,495 |
setenv mainlineLinux yes setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs earlyprintk=serial' setenv usb_load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' setenv usb_load_uinitrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd' run set_bootargs run usb_load_uimage run usb_load_uinitrd printenv bootargs printenv mw 0x800000 0 1 bootm 0x800000 0x1100000
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 19, 2017 01:02AM |
Registered: 6 years ago Posts: 24 |
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** MARVELL BOARD: DB6702A-GMtech LE U-Boot 1.1.4 (Jun 5 2013 - 10:49:39) Marvell version: 3.6.0 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00 Soc: 88F6702 A1 CPU running @ 1000Mhz L2 running @ 500Mhz SysClock = 400Mhz , TClock = 166Mhz DRAM (DDR2) CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:256 MB Flash: 0 kB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 Marvell>> setenv mainlineLinux yes Marvell>> setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=' Marvell>> setenv usb_load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' Marvell>> setenv usb_load_uinitrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd' Marvell>> run set_bootargs I don't know if you missed that command so I added here: Marvell>> usb start (Re)start USB... USB: scanning bus for devices... 2 USB Device(s) found Waiting for storage device(s) to settle before scanning... 1 Storage Device(s) found (without that command it goes directly to ## Booting image at 00800000 ... Bad Magic Number ) then Marvell>> run usb_load_uimage .... . ...... ............ ......................... ................................................... ................................................................................ ................................................................................ 3834884 bytes read Marvell>> run usb_load_uinitrd .... . ...... ............ ......................... ................................................... ................................................................................ ................................................................................ .... ................................................................................ 7245696 bytes read Marvell>> printenv bootargs bootargs=console=ttyS0,115200 root=LABEL=rootfs earlyprintk=serial Marvell>> printenv baudrate=115200 loads_echo=0 serverip=10.4.52.7 run_diag=yes MALLOC_len=1 ethprime=egiga0 bootargs_end=:::DB88FXX81:eth0:none ethmtu=1500 mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 nandEcc=1bit netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no image_multi=yes ethact=egiga0 console=console=ttyS0,115200 ethaddr=00:11:41:3C:59:24 standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/; bootargs_root=ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc bootcmd=nand read.e 0x800000 0x100000 0x400000; setenv bootargs $(console) $(bo0 rootpath=/tftpboot_tokyo/marvell_nfs bootfile=/pxelinux.0 gatewayip=192.168.178.1 netmask=255.255.255.0 ipaddr=192.168.178.250 image_name=uImage.medion stdin=serial stdout=serial stderr=serial enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no enaAutoRecovery=yes pcieTune=no mainlineLinux=yes set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs earlyprintkl usb_load_uimage=ext2load usb 0:1 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb 0:1 0x1100000 /boot/uInitrd bootargs=console=ttyS0,115200 root=LABEL=rootfs earlyprintk=serial filesize=6E8F80 Environment size: 1540/131068 bytes Marvell>> mw 0x800000 0 1 Marvell>> bootm 0x800000 0x1100000 ## Booting image at 00800000 ... Bad Magic Number
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 19, 2017 03:55AM |
Admin Registered: 13 years ago Posts: 18,495 |
setenv mainlineLinux yes setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs earlyprintk=serial' setenv usb_load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' setenv usb_load_uinitrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd' run set_bootargs printenv bootargs printenv usb start mw 0x800000 0 1 run usb_load_uimage run usb_load_uinitrd bootm 0x800000 0x1100000
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 19, 2017 04:07AM |
Registered: 6 years ago Posts: 24 |
Marvell>> setenv mainlineLinux yes Marvell>> setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=' Marvell>> setenv usb_load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' Marvell>> setenv usb_load_uinitrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd' Marvell>> run set_bootargs Marvell>> printenv bootargs bootargs=console=ttyS0,115200 root=LABEL=rootfs earlyprintk=serial Marvell>> printenv baudrate=115200 loads_echo=0 serverip=10.4.52.7 run_diag=yes MALLOC_len=1 ethprime=egiga0 bootargs_end=:::DB88FXX81:eth0:none ethmtu=1500 mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 nandEcc=1bit netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no image_multi=yes ethact=egiga0 console=console=ttyS0,115200 ethaddr=00:11:41:3C:59:24 standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/; bootargs_root=ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc bootcmd=nand read.e 0x800000 0x100000 0x400000; setenv bootargs $(console) $(bo0 rootpath=/tftpboot_tokyo/marvell_nfs bootfile=/pxelinux.0 gatewayip=192.168.178.1 netmask=255.255.255.0 ipaddr=192.168.178.250 image_name=uImage.medion stdin=serial stdout=serial stderr=serial enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no enaAutoRecovery=yes pcieTune=no mainlineLinux=yes set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs earlyprintkl usb_load_uimage=ext2load usb 0:1 0x800000 /boot/uImage usb_load_uinitrd=ext2load usb 0:1 0x1100000 /boot/uInitrd bootargs=console=ttyS0,115200 root=LABEL=rootfs earlyprintk=serial Environment size: 1524/131068 bytes Marvell>> usb start (Re)start USB... USB: scanning bus for devices... 2 USB Device(s) found Waiting for storage device(s) to settle before scanning... 1 Storage Device(s) found Marvell>> mw 0x800000 0 1 Marvell>> run usb_load_uimage .... . ...... ............ ......................... ................................................... ................................................................................ ................................................................................ 3834884 bytes read Marvell>> run usb_load_uinitrd .... . ...... ............ ......................... ................................................... ................................................................................ ................................................................................ .... ................................................................................ 7245696 bytes read Marvell>> bootm 0x800000 0x1100000 ## Booting image at 00800000 ... Image Name: Linux-4.12.1-kirkwood-tld-1 Created: 2017-11-18 13:59:37 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3834820 Bytes = 3.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 01100000 ... Image Name: initramfs-4.12.1-kirkwood-tld-1 Created: 2017-07-24 0:18:23 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7245632 Bytes = 6.9 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ...and nothing more...
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 19, 2017 04:52AM |
Admin Registered: 13 years ago Posts: 18,495 |
ls -l /media/sdb1 ls -latr /media/sdb1/boot
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 19, 2017 04:59AM |
Registered: 6 years ago Posts: 24 |
insgesamt 192032 drwxr-xr-x 2 root root 4096 Jul 24 02:12 bin drwxr-xr-x 3 root root 4096 Nov 18 14:59 boot -rw-r--r-- 1 root root 196352036 Nov 12 12:25 Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2 drwxr-xr-x 5 root root 4096 Feb 24 2012 dev drwxr-xr-x 57 root root 4096 Nov 18 14:54 etc drwxr-xr-x 2 root root 4096 Jan 22 2012 home drwxr-xr-x 14 root root 4096 Jul 20 10:55 lib drwx------ 2 root root 16384 Feb 24 2012 lost+found drwxr-xr-x 2 root root 4096 Feb 24 2012 media drwxr-xr-x 2 root root 4096 Feb 10 2015 mnt drwxr-xr-x 2 root root 4096 Feb 24 2012 opt drwxr-xr-x 2 root root 4096 Jan 22 2012 proc drwx------ 5 root root 4096 Jul 24 03:49 root drwxr-xr-x 2 root root 4096 Feb 8 2013 run drwxr-xr-x 2 root root 4096 Jul 24 02:12 sbin drwxr-xr-x 2 root root 4096 Feb 24 2012 srv drwxr-xr-x 2 root root 4096 Jan 1 2011 sys drwxrwxrwt 2 root root 4096 Jan 1 1970 tmp drwxr-xr-x 10 root root 4096 Feb 24 2012 usr drwxr-xr-x 11 root root 4096 Jan 1 1970 var /boot insgesamt 43764 drwxr-xr-x 21 root root 4096 Feb 17 2015 .. drwxr-xr-x 2 root root 4096 Jul 16 00:14 dts -rw-r--r-- 1 root root 153501 Jul 16 05:21 config-4.12.1-kirkwood-tld-1 -rwxr-xr-x 1 root root 3821528 Jul 16 06:42 zImage-4.12.1-kirkwood-tld-1 -rw------- 1 root root 3821528 Jul 16 09:43 vmlinuz-4.12.1-kirkwood-tld-1 -rw------- 1 root root 2504031 Jul 16 09:43 System.map-4.12.1-kirkwood-tld-1 -rw-r--r-- 1 root root 8435004 Jul 16 10:06 linux-headers-4.12.1-kirkwood-tld-1_1.0_armel.deb -rw-r--r-- 1 root root 3821592 Jul 20 10:11 uImage.orig -rw-r--r-- 1 root root 7245632 Jul 24 02:15 initrd.img-4.12.1-kirkwood-tld-1 -rw-r--r-- 1 root root 7245696 Jul 24 02:18 uInitrd -rwxr-xr-x 1 root root 3834820 Nov 18 14:59 zImage.fdt drwxr-xr-x 3 root root 4096 Nov 18 14:59 . -rw-r--r-- 1 root root 3834884 Nov 18 14:59 uImage
Marvell>> printenv baudrate=115200 loads_echo=0 serverip=10.4.52.7 run_diag=yes MALLOC_len=1 ethprime=egiga0 bootargs_end=:::DB88FXX81:eth0:none ethmtu=1500 mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 nandEcc=1bit netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no image_multi=yes ethact=egiga0 console=console=ttyS0,115200 ethaddr=00:11:41:3C:59:24 standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; bootargs_root=ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc bootargs=console=ttyS0,115200 ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc bootcmd=nand read.e 0x800000 0x100000 0x400000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000 rootpath=/tftpboot_tokyo/marvell_nfs bootfile=/pxelinux.0 gatewayip=192.168.178.1 netmask=255.255.255.0 ipaddr=192.168.178.250 image_name=uImage.medion stdin=serial stdout=serial stderr=serial mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no enaAutoRecovery=yes pcieTune=no Environment size: 1349/131068 bytes
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 19, 2017 05:39AM |
Admin Registered: 13 years ago Posts: 18,495 |
-rw-r--r-- 1 root root 3821592 Jul 20 10:11 uImage.orig
setenv mainlineLinux yes setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' setenv usb_load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' run set_bootargs printenv bootargs usb start mw 0x800000 0 1 run usb_load_uimage bootm 0x800000
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 19, 2017 10:50AM |
Registered: 6 years ago Posts: 24 |
setenv mainlineLinux yes Marvell>> setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' Marvell>> setenv usb_load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' Marvell>> run set_bootargs Marvell>> printenv bootargs bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial Marvell>> usb start (Re)start USB... USB: scanning bus for devices... 2 USB Device(s) found Waiting for storage device(s) to settle before scanning... 1 Storage Device(s) found Marvell>> mw 0x800000 0 1 Marvell>> run usb_load_uimage .... . ...... ............ ......................... ................................................... ...................................................................................................... ......................................................................................................................................................................... 3834884 bytes read Marvell>> bootm 0x800000 ## Booting image at 00800000 ... Image Name: Linux-4.12.1-kirkwood-tld-1 Created: 2017-11-18 13:59:37 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3834820 Bytes = 3.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ...
cp -a zImage-4.12.1-kirkwood-tld-1 zImage.fdt cat dts/kirkwood-nsa320s.dtb >> zImage.fdt mv uImage uImage.orig mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-4.12.1-kirkwood-tld-1 -d zImage.fdt uImage sync
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 19, 2017 04:59PM |
Admin Registered: 13 years ago Posts: 18,495 |
> cp -a zImage-4.12.1-kirkwood-tld-1 zImage.fdt > cat dts/kirkwood-nsa320s.dtb >> zImage.fdt > mv uImage uImage.orig > mkimage -A arm -O linux -T kernel -C none -a > 0x00008000 -e 0x00008000 -n > Linux-4.12.1-kirkwood-tld-1 -d zImage.fdt uImage > sync >
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 20, 2017 10:40AM |
Registered: 6 years ago Posts: 24 |
root@SaschSamsung:/media/saschbaer/rootfs/boot# cd /mnt/sdd1/boot root@SaschSamsung:/mnt/sdd1/boot# ls config-4.12.1-kirkwood-tld-1 System.map-4.12.1-kirkwood-tld-1 vmlinuz-4.12.1-kirkwood-tld-1 dts uImage zImage-4.12.1-kirkwood-tld-1 initrd.img-4.12.1-kirkwood-tld-1 uImage.orig zImage.fdt linux-headers-4.12.1-kirkwood-tld-1_1.0_armel.deb uInitrd root@SaschSamsung:/mnt/sdd1/boot# rm zImage.fdt root@SaschSamsung:/mnt/sdd1/boot# cp -a zImage-4.12.1-kirkwood-tld-1 zImage.fdt -v 'zImage-4.12.1-kirkwood-tld-1' -> 'zImage.fdt' root@SaschSamsung:/mnt/sdd1/boot# cat dts/kirkwood-nsa320s.dtb >> zImage.fdt -v root@SaschSamsung:/mnt/sdd1/boot# rm uImage root@SaschSamsung:/mnt/sdd1/boot# cp uImage.orig uImage -v 'uImage.orig' -> 'uImage' root@SaschSamsung:/mnt/sdd1/boot# mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-4.12.1-kirkwood-tld-1 -d zImage.fdt uImage -v Usage: mkimage -l image -l ==> list image header information mkimage [-x] -A arch -O os -T type -C comp -a addr -e ep -n name -d data_file[:data_file...] image -A ==> set architecture to 'arch' -O ==> set operating system to 'os' -T ==> set image type to 'type' -C ==> set compression type 'comp' -a ==> set load address to 'addr' (hex) -e ==> set entry point to 'ep' (hex) -n ==> set image name to 'name' -d ==> use image data from 'datafile' -x ==> set XIP (execute in place) mkimage [-D dtc_options] [-f fit-image.its|-F] fit-image -D => set all options for device tree compiler -f => input filename for FIT source Signing / verified boot not supported (CONFIG_FIT_SIGNATURE undefined) mkimage -V ==> print version information and exit Use -T to see a list of available image types root@SaschSamsung:/mnt/sdd1/boot# mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-4.12.1-kirkwood-tld-1 -d zImage.fdt uImage Image Name: Linux-4.12.1-kirkwood-tld-1 Created: Mon Nov 20 17:37:30 2017 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3844115 Bytes = 3754.02 kB = 3.67 MB Load Address: 00008000 Entry Point: 00008000 root@SaschSamsung:/mnt/sdd1/boot# sync -v sync: Ungültige Option -- v „sync --help“ liefert weitere Informationen. root@SaschSamsung:/mnt/sdd1/boot# sync root@SaschSamsung:/mnt/sdd1/boot# sync root@SaschSamsung:/mnt/sdd1/boot# sync
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 20, 2017 04:26PM |
Admin Registered: 13 years ago Posts: 18,495 |
setenv mainlineLinux yes setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' setenv usb_load_uimage 'ext2load usb 0:1 0x02000000 /boot/uImage' run set_bootargs printenv bootargs usb start run usb_load_uimage bootm 0x02000000
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 21, 2017 12:52PM |
Registered: 6 years ago Posts: 24 |
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** MARVELL BOARD: DB6702A-GMtech LE U-Boot 1.1.4 (Jun 5 2013 - 10:49:39) Marvell version: 3.6.0 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00 Soc: 88F6702 A1 CPU running @ 1000Mhz L2 running @ 500Mhz SysClock = 400Mhz , TClock = 166Mhz DRAM (DDR2) CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:256 MB Flash: 0 kB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 Marvell>> setenv mainlineLinux yes Marvell>> setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' Marvell>> setenv usb_load_uimage 'ext2load usb 0:1 0x02000000 /boot/uImage' Marvell>> run set_bootargs Marvell>> printenv bootargs bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial Marvell>> usb start (Re)start USB... USB: scanning bus for devices... 2 USB Device(s) found Waiting for storage device(s) to settle before scanning... 1 Storage Device(s) found Marvell>> run usb_load_uimage .... . ...... ............ ......................... ................................................... ...................................................................................................... .......................................................................................................................................................................... 3844179 bytes read Marvell>> bootm 0x02000000 ## Booting image at 02000000 ... Image Name: Linux-4.12.1-kirkwood-tld-1 Created: 2017-11-20 16:37:30 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3844115 Bytes = 3.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ...
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 21, 2017 04:25PM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? November 21, 2017 11:40PM |
Registered: 6 years ago Posts: 24 |
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? December 14, 2017 06:40AM |
Registered: 8 years ago Posts: 295 |
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? December 14, 2017 07:18AM |
Registered: 6 years ago Posts: 24 |
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? December 14, 2017 08:14AM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: Possible to get Debian on a Medion NAS P89654 2x4 TB? January 24, 2018 06:18PM |
Registered: 7 years ago Posts: 27 |