Need help/advice on brand new pogoplugV4 November 01, 2017 01:48PM |
Registered: 6 years ago Posts: 8 |
1.010000] Scanning device for bad blocks [ 1.010000] Bad eraseblock 4 at 0x000000080000 [ 1.050000] Bad eraseblock 697 at 0x000005720000
Re: Need help/advice on brand new pogoplugV4 November 01, 2017 03:54PM |
Admin Registered: 13 years ago Posts: 18,564 |
Re: Need help/advice on brand new pogoplugV4 November 01, 2017 04:08PM |
Admin Registered: 13 years ago Posts: 18,564 |
Quote
Important Note: If possible, try to test this boot image with UART booting before flashing to NAND. See davygravy's UART booting using kwboot instruction here in this thread. The latest u-boot image released here should be used for UART booting, if your box is the type that supports it (these do not: Dockstar, Pogo E02, iConnect).
Quote
To download ARM kwboot binary for UART booting at Dropbox
kwboot-2016.05.tar
md5:
76977c5a61544a5707dfa17ae832a3ad
sha256:
25ee4fa8a94372d2d398cac4704e9ee3ca87585c29e72e18323209b7f163209d
kwboot (this is an older version)
md5:
0efd011bdb244436e432a8de33e639a1
cat /proc/mtd ls -l /dev/mtd*
Re: Need help/advice on brand new pogoplugV4 November 01, 2017 04:10PM |
Admin Registered: 13 years ago Posts: 18,564 |
Re: Need help/advice on brand new pogoplugV4 November 01, 2017 11:24PM |
Registered: 6 years ago Posts: 8 |
~ # cat /proc/mtd dev: size erasesize name mtd0: 00200000 00020000 "u-boot" mtd1: 00300000 00020000 "uImage" mtd2: 00300000 00020000 "uImage2" mtd3: 00800000 00020000 "failsafe" mtd4: 07000000 00020000 "root" ~ # ls -l /de ~ # ls -l /dev/mtd* crw-rw---- 1 root root 90, 0 Feb 26 2008 /dev/mtd0 crw-rw---- 1 root root 90, 2 Feb 26 2008 /dev/mtd1 crw-rw---- 1 root root 90, 20 Feb 26 2008 /dev/mtd10 crw-rw---- 1 root root 90, 22 Feb 26 2008 /dev/mtd11 crw-rw---- 1 root root 90, 24 Feb 26 2008 /dev/mtd12 crw-rw---- 1 root root 90, 26 Feb 26 2008 /dev/mtd13 crw-rw---- 1 root root 90, 28 Feb 26 2008 /dev/mtd14 crw-rw---- 1 root root 90, 30 Feb 26 2008 /dev/mtd15 crw-rw---- 1 root root 90, 4 Feb 26 2008 /dev/mtd2 crw-rw---- 1 root root 90, 6 Feb 26 2008 /dev/mtd3 crw-rw---- 1 root root 90, 8 Feb 26 2008 /dev/mtd4 crw-rw---- 1 root root 90, 10 Feb 26 2008 /dev/mtd5 crw-rw---- 1 root root 90, 12 Feb 26 2008 /dev/mtd6 crw-rw---- 1 root root 90, 14 Feb 26 2008 /dev/mtd7 crw-rw---- 1 root root 90, 16 Feb 26 2008 /dev/mtd8 crw-rw---- 1 root root 90, 18 Feb 26 2008 /dev/mtd9 brw-r--r-- 1 root root 31, 0 Feb 26 2008 /dev/mtdblock0 brw-r--r-- 1 root root 31, 1 Feb 26 2008 /dev/mtdblock1 brw-r--r-- 1 root root 31, 2 Feb 26 2008 /dev/mtdblock2 brw-r--r-- 1 root root 31, 3 Feb 26 2008 /dev/mtdblock3 brw-r--r-- 1 root root 31, 4 Feb 26 2008 /dev/mtdblock4 brw-r--r-- 1 root root 31, 5 Feb 26 2008 /dev/mtdblock5 brw-r--r-- 1 root root 31, 6 Feb 26 2008 /dev/mtdblock6 brw-r--r-- 1 root root 31, 7 Feb 26 2008 /dev/mtdblock7
Re: Need help/advice on brand new pogoplugV4 November 01, 2017 11:57PM |
Admin Registered: 13 years ago Posts: 18,564 |
> ~ # cat /proc/mtd > dev: size erasesize name > mtd0: 00200000 00020000 "u-boot"
Quote
6. Erase mtd0
flash_erase /dev/mtd0 0 4
Expected output:
Erase Total 4 Units
Performing Flash Erase of length 131072 at offset 0x60000 done
7. Write image to NAND
Among the nandwrite commands below, be extra careful and execute only one nandwrite command corresponding to your platform that you are installing to, using the kwb file that you have extracted in step 5. Please double check to make sure the file is for the correct platform. Especially the similar sounding names (e.g. nsa310s and nsa310 are different u-boots).
nandwrite /dev/mtd0 uboot.2017.07-tld-1.dockstar.mtd0.kwb
nandwrite /dev/mtd0 uboot.2017.07-tld-1.goflexhome.mtd0.kwb
nandwrite /dev/mtd0 uboot.2017.07-tld-1.goflexnet.mtd0.kwb
nandwrite /dev/mtd0 uboot.2017.07-tld-1.iconnect.mtd0.kwb
nandwrite /dev/mtd0 uboot.2017.07-tld-1.netgear_ms2110.mtd0.kwb
nandwrite /dev/mtd0 uboot.2017.07-tld-1.pogo_e02.mtd0.kwb
nandwrite /dev/mtd0 uboot.2017.07-tld-1.pogo_v4.mtd0.kwb
nandwrite /dev/mtd0 uboot.2017.07-tld-1.sheevaplug.mtd0.kwb
nandwrite /dev/mtd0 uboot.2017.07-tld-1.nsa320.mtd0.kwb
nandwrite /dev/mtd0 uboot.2017.07-tld-1.nsa325.mtd0.kwb
nandwrite /dev/mtd0 uboot.2017.07-tld-1.nsa310s.mtd0.kwb
nandwrite /dev/mtd0 uboot.2017.07-tld-1.nsa310.mtd0.kwb
Expected output:
Writing data to block 0 at offset 0x0
Writing data to block 1 at offset 0x20000
Writing data to block 2 at offset 0x40000
Writing data to block 3 at offset 0x60000
Re: Need help/advice on brand new pogoplugV4 November 02, 2017 03:43PM |
Registered: 6 years ago Posts: 8 |
Pogov4> printenv arcNumber=3960 baudrate=115200 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm$load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb console=ttyS0,115200 device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-pogoplug_v4 ethact=egiga0 ethaddr=52:3b:20:9c:11:51 if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15 Environment size: 2907/131068 bytes
Re: Need help/advice on brand new pogoplugV4 November 02, 2017 03:57PM |
Admin Registered: 13 years ago Posts: 18,564 |
setenv dtb_file kirkwood-pogo_v4.dtb
Re: Need help/advice on brand new pogoplugV4 November 03, 2017 12:27PM |
Registered: 6 years ago Posts: 8 |
root@debian:/tmp# flash_erase /dev/mtd0 0 4 Erasing 128 Kibyte @ 7f5eaf5c00000064 -- 4 % complete root@debian:/tmp# nandwrite /dev/mtd0 uboot.2017.07-tld-1.pogo_v4.mtd0.kwb Writing data to block 0 at offset 0x0 Writing data to block 1 at offset 0x20000 Writing data to block 2 at offset 0x40000 Writing data to block 3 at offset 0x60000 root@debian:/tmp#
Re: Need help/advice on brand new pogoplugV4 November 03, 2017 05:05PM |
Admin Registered: 13 years ago Posts: 18,564 |
> root@debian:/tmp# flash_erase /dev/mtd0 0 4 > Erasing 128 Kibyte @ 7f5eaf5c00000064 -- 4 % > complete > > root@debian:/tmp# nandwrite /dev/mtd0 > uboot.2017.07-tld-1.pogo_v4.mtd0.kwb > Writing data to block 0 at offset 0x0 > Writing data to block 1 at offset 0x20000 > Writing data to block 2 at offset 0x40000 > Writing data to block 3 at offset 0x60000 > root@debian:/tmp# > >
Re: Need help/advice on brand new pogoplugV4 November 03, 2017 10:44PM |
Registered: 6 years ago Posts: 8 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:34:01 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: MVEBU_MMC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Reset IDE: ide_preinit failed MMC rescan: current device # 0 initialized OK ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... ** Bad device usb 0 ** no IDE devices available Partition Map for MMC device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 15124480 1ae5ab55-01 83 loading envs from mmc 0 ... ** File not found /boot/uEnv.txt ** running scan_disk ... Scan device usb device usb 0:1 ** Bad device usb 0 ** device usb 1:1 ** Bad device usb 1 ** device usb 2:1 ** Bad device usb 2 ** device usb 3:1 ** Bad device usb 3 ** Scan device ide Reset IDE: ide_preinit failed device ide 0:1 ** Bad device ide 0 ** device ide 1:1 ** Bad device ide 1 ** device ide 2:1 ** Bad device ide 2 ** device ide 3:1 ** Bad device ide 3 ** Scan device mmc MMC rescan: current device # 0 initialized OK device mmc 0:1 1 bytes read in 35 ms (0 Bytes/s) Found bootable drive on mmc 0 loading uImage ... 3821592 bytes read in 125 ms (29.2 MiB/s) loading uInitrd ... 7245696 bytes read in 190 ms (36.4 MiB/s) loading DTB /boot/dts/kirkwood-pogoplug_v4 ... ** File not found /boot/dts/kirkwood-pogoplug_v4 ** ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.12.1-kirkwood-tld-1 Created: 2017-07-20 8:11:24 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3821528 Bytes = 3.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.12.1-kirkwood-tld-1 Created: 2017-07-24 0:18:23 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7245632 Bytes = 6.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK Loading Ramdisk to 07420000, end 07b08f40 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Error: unrecognized/unsupported machine ID (r1 = 0x00000f78). Available machine support: ID (hex) NAME ffffffff Generic DT based system ffffffff Marvell Kirkwood (Flattened Device Tree) Please check your kernel config and/or bootloader.I solved it this way:
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:34:01 -0700) Pogoplug V4 SoC: Kirkwood 88F6192_A1 DRAM: 128 MiB WARNING: Caches not enabled NAND: 128 MiB MMC: MVEBU_MMC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: egiga0 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Reset IDE: ide_preinit failed MMC rescan: current device # 0 initialized OK ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... ** Bad device usb 0 ** no IDE devices available Partition Map for MMC device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 15124480 1ae5ab55-01 83 loading envs from mmc 0 ... 2790 bytes read in 42 ms (64.5 KiB/s) importing envs ... Warning: egiga0 MAC addresses don't match: Address in SROM is 00:25:31:04:de:09 Address in environment is 52:3b:20:9c:11:51 running scan_disk ... Scan device usb device usb 0:1 ** Bad device usb 0 ** device usb 1:1 ** Bad device usb 1 ** device usb 2:1 ** Bad device usb 2 ** device usb 3:1 ** Bad device usb 3 ** Scan device ide Reset IDE: ide_preinit failed device ide 0:1 ** Bad device ide 0 ** device ide 1:1 ** Bad device ide 1 ** device ide 2:1 ** Bad device ide 2 ** device ide 3:1 ** Bad device ide 3 ** Scan device mmc MMC rescan: current device # 0 initialized OK device mmc 0:1 1 bytes read in 35 ms (0 Bytes/s) Found bootable drive on mmc 0 loading uImage ... 3821592 bytes read in 124 ms (29.4 MiB/s) loading uInitrd ... 7245696 bytes read in 190 ms (36.4 MiB/s) loading DTB /boot/dts/kirkwood-pogoplug_v4.dtb ... 10284 bytes read in 123 ms (81.1 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.12.1-kirkwood-tld-1 Created: 2017-07-20 8:11:24 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3821528 Bytes = 3.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.12.1-kirkwood-tld-1 Created: 2017-07-24 0:18:23 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7245632 Bytes = 6.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 07420000, end 07b08f40 ... OK Loading Device Tree to 0741a000, end 0741f82b ... OK Using machid 0xf78 from environment Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.1-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: Pogoplug v4 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 109428K/131072K available (8192K kernel code, 716K rwdata, 1972K rodata, 1024K init, 288K bss, 21644K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db3274 ( 717 kB) [ 0.000000] .bss : 0xc0db9b9c - 0xc0e01e60 ( 289 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 0.000012] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 0.000066] Switching to timer-based delay loop, resolution 6ns [ 0.000765] Console: colour dummy device 80x30 [ 0.000815] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666) [ 0.000850] pid_max: default: 32768 minimum: 301 [ 0.001145] Security Framework initialized [ 0.001328] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001357] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.002643] CPU: Testing write buffer coherency: ok [ 0.004217] Setting up static identity map for 0x100000 - 0x100058 [ 0.004614] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.009531] devtmpfs: initialized [ 0.015388] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.015428] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.016039] prandom: seed boundary self test passed [ 0.021771] prandom: 100 self tests passed [ 0.021797] pinctrl core: initialized pinctrl subsystem [ 0.023548] NET: Registered protocol family 16 [ 0.024285] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.026644] cpuidle: using governor ladder [ 0.026755] cpuidle: using governor menu [ 0.027400] Feroceon L2: Enabling L2 [ 0.027465] Feroceon L2: Cache support initialised. [ 0.028014] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.035045] No ATAGs? [ 0.048368] vgaarb: loaded [ 0.048833] SCSI subsystem initialized [ 0.049499] usbcore: registered new interface driver usbfs [ 0.049624] usbcore: registered new interface driver hub [ 0.049746] usbcore: registered new device driver usb [ 0.051415] clocksource: Switched to clocksource orion_clocksource [ 0.183747] VFS: Disk quotas dquot_6.6.0 [ 0.183866] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.198740] NET: Registered protocol family 2 [ 0.199807] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.199850] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.199881] TCP: Hash tables configured (established 1024 bind 1024) [ 0.200012] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.200047] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.200297] NET: Registered protocol family 1 [ 0.200885] RPC: Registered named UNIX socket transport module. [ 0.200903] RPC: Registered udp transport module. [ 0.200914] RPC: Registered tcp transport module. [ 0.200924] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.201260] Unpacking initramfs... [ 1.168610] Freeing initrd memory: 7076K [ 1.168816] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.170190] audit: initializing netlink subsys (disabled) [ 1.170897] Initialise system trusted keyrings [ 1.170969] Key type blacklist registered [ 1.171108] audit: type=2000 audit(1.169:1): state=initialized audit_enabled=0 res=1 [ 1.171242] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 1.171341] zbud: loaded [ 1.172867] NFS: Registering the id_resolver key type [ 1.172903] Key type id_resolver registered [ 1.172916] Key type id_legacy registered [ 1.172940] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.172955] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.173242] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.173520] fuse init (API version 7.26) [ 1.174037] orangefs_debugfs_init: called with debug mask: :none: :0: [ 1.174438] orangefs_init: module version upstream loaded [ 1.174454] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 2.551423] random: fast init done [ 9.946489] Key type asymmetric registered [ 9.946513] Asymmetric key parser 'x509' registered [ 9.946614] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 9.946630] io scheduler noop registered [ 9.946643] io scheduler deadline registered [ 9.946757] io scheduler cfq registered (default) [ 9.948011] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 47 [ 9.948036] kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 49 [ 9.948536] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 9.951336] mvebu-pcie mbus@f1000000:pcie-controller@82000000: PCI host bridge to bus 0000:00 [ 9.951367] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 9.951387] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 9.951646] pci_bus 0000:00: root bus resource [bus 00-ff] [ 9.952145] PCI: bus0: Fast back to back transfers disabled [ 9.952180] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 9.981505] PCI: bus1: Fast back to back transfers disabled [ 9.981793] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 9.981824] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit] [ 9.981857] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0010000-0xe0010fff 64bit] [ 9.981889] pci 0000:01:00.0: BAR 4: assigned [mem 0xe0011000-0xe0011fff 64bit] [ 9.981917] pci 0000:00:01.0: PCI bridge to [bus 01] [ 9.981942] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 9.982071] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 9.982208] pci 0000:01:00.0: enabling device (0140 -> 0142) [ 9.982934] mv_xor f1060800.xor: Marvell shared XOR driver [ 10.042537] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 10.042852] mv_xor f1060900.xor: Marvell shared XOR driver [ 10.102563] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 10.103194] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 10.105115] console [ttyS0] disabled [ 10.105207] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 10416666) is a 16550A [ 10.813265] console [ttyS0] enabled [ 10.829158] loop: module loaded [ 10.833194] sata_mv f1080000.sata: slots 32 ports 2 [ 10.842015] scsi host0: sata_mv [ 10.845791] scsi host1: sata_mv [ 10.849257] ata1: SATA max UDMA/133 irq 32 [ 10.853416] ata2: SATA max UDMA/133 irq 32 [ 10.858987] nand: Could not find valid ONFI parameter page; aborting [ 10.865434] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1 [ 10.871794] nand: Hynix NAND 128MiB 3,3V 8-bit [ 10.876225] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 10.883802] Scanning device for bad blocks [ 10.888268] Bad eraseblock 4 at 0x000000080000 [ 10.950068] Bad eraseblock 697 at 0x000005720000 [ 10.981713] 5 cmdlinepart partitions found on MTD device orion_nand [ 10.987954] Creating 5 MTD partitions on "orion_nand": [ 10.993105] 0x000000000000-0x000000200000 : "u-boot" [ 10.999919] 0x000000200000-0x000000500000 : "uImage" [ 11.006763] 0x000000500000-0x000000800000 : "uImage2" [ 11.013689] 0x000000800000-0x000001000000 : "failsafe" [ 11.020747] 0x000001000000-0x000008000000 : "root" [ 11.029899] libphy: Fixed MDIO Bus: probed [ 11.035212] libphy: orion_mdio_bus: probed [ 11.046565] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 11.183083] ata1: SATA link down (SStatus 0 SControl F300) [ 11.532944] ata2: SATA link down (SStatus 0 SControl F300) [ 12.163576] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 52:3b:20:9c:11:51 [ 12.172471] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 12.178999] ehci-pci: EHCI PCI platform driver [ 12.183550] ehci-orion: EHCI orion driver [ 12.187845] orion-ehci f1050000.ehci: EHCI Host Controller [ 12.193394] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 12.201266] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000 [ 12.231463] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 12.237784] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 12.244591] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 12.251809] usb usb1: Product: EHCI Host Controller [ 12.256673] usb usb1: Manufacturer: Linux 4.12.1-kirkwood-tld-1 ehci_hcd [ 12.263383] usb usb1: SerialNumber: f1050000.ehci [ 12.269050] hub 1-0:1.0: USB hub found [ 12.272944] hub 1-0:1.0: 1 port detected [ 12.277726] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 12.283072] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2 [ 12.292064] xhci_hcd 0000:01:00.0: hcc params 0x200073a1 hci version 0x100 quirks 0x00080010 [ 12.300786] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 12.307596] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 12.314821] usb usb2: Product: xHCI Host Controller [ 12.319683] usb usb2: Manufacturer: Linux 4.12.1-kirkwood-tld-1 xhci-hcd [ 12.326389] usb usb2: SerialNumber: 0000:01:00.0 [ 12.331997] hub 2-0:1.0: USB hub found [ 12.335787] hub 2-0:1.0: 2 ports detected [ 12.340519] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 12.345833] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3 [ 12.353418] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 12.361743] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 [ 12.368511] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 12.375739] usb usb3: Product: xHCI Host Controller [ 12.380606] usb usb3: Manufacturer: Linux 4.12.1-kirkwood-tld-1 xhci-hcd [ 12.388160] usb usb3: SerialNumber: 0000:01:00.0 [ 12.393754] hub 3-0:1.0: USB hub found [ 12.397542] hub 3-0:1.0: 2 ports detected [ 12.402689] usbcore: registered new interface driver usb-storage [ 12.409175] mousedev: PS/2 mouse device common for all mice [ 12.691463] usb 2-2: new high-speed USB device number 2 using xhci_hcd [ 12.863583] usb 2-2: New USB device found, idVendor=1307, idProduct=0163 [ 12.870263] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 12.877406] usb 2-2: Product: USB Mass Storage Device [ 12.882468] usb 2-2: Manufacturer: USBest Technology [ 12.887431] usb 2-2: SerialNumber: 00000000000381 [ 12.893653] usb-storage 2-2:1.0: USB Mass Storage device detected [ 12.900186] scsi host2: usb-storage 2-2:1.0 [ 13.441465] rtc-mv f1010300.rtc: internal RTC not ticking [ 13.447108] i2c /dev entries driver [ 13.452489] hidraw: raw HID events driver (C) Jiri Kosina [ 13.458367] drop_monitor: Initializing network drop monitor service [ 13.465017] NET: Registered protocol family 17 [ 13.469561] Key type dns_resolver registered [ 13.474875] registered taskstats version 1 [ 13.478962] Loading compiled-in X.509 certificates [ 13.483869] zswap: loaded using pool lzo/zbud [ 13.502878] Key type big_key registered [ 13.520367] Key type encrypted registered [ 13.526596] hctosys: unable to open rtc device (rtc0) [ 13.536706] Freeing unused kernel memory: 1024K Loading, please wait... starting version 232 [ 13.927641] scsi 2:0:0:0: Direct-Access UDISK PDU15_4G 81I2.0 0.00 PQ: 0 ANSI: 2 [ 13.951703] sd 2:0:0:0: [sda] 7897087 512-byte logical blocks: (4.04 GB/3.76 GiB) [ 13.975377] sd 2:0:0:0: [sda] Write Protect is off [ 13.985517] sd 2:0:0:0: [sda] Asking for cache data failed [ 13.991002] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 14.137454] usbcore: registered new interface driver uas [ 14.186473] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 14.200440] GPT:1122303 != 7897086 [ 14.207928] GPT:Alternate GPT header not at the end of the disk. [ 14.219092] GPT:1122303 != 7897086 [ 14.225630] GPT: Use GNU Parted to correct GPT errors. [ 14.230895] sda: sda1 sda2 [ 14.325129] sd 2:0:0:0: [sda] Attached SCSI removable disk [ 14.374570] mvsdio f1090000.mvsdio: Got CD GPIO [ 14.478197] mmc0: host does not support reading read-only switch, assuming write-enable [ 14.493727] mmc0: new high speed SDHC card at address 1234 [ 14.780728] mmcblk0: mmc0:1234 SA08G 7.21 GiB [ 14.789715] mmcblk0: p1 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Warning: fsck not present, so skipping root file system [ 25.316609] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem [ 25.337110] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [ ok ] Setting hostname to 'debian'...done. [....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232 . ok [....] Synthesizing the initial hotplug events...[ 28.009989] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [ ok done. [....] Waiting for /dev to be fully populated...[ 28.582502] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 28.637321] marvell-cesa f1030000.crypto: CESA device successfully registered [ 28.670382] orion_wdt: Initial timeout 25 sec done. [ ok ] Activating swap:. [ 30.345425] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null) [....] Will now check root file system:fsck from util-linux 2.29.2 [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/mmcblk0p1 e2fsck 1.43.4 (31-Jan-2017) rootfs: clean, 14534/473280 files, 248208/1890560 blocks . ok [ 30.662034] EXT4-fs (mmcblk0p1): re-mounted. Opts: errors=remount-ro [ ok ] Will now activate lvm and md swap:done. [info] Will now check all file systems. fsck from util-linux 2.29.2 Checking all file systems. LABEL=rootfs is mounted [....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs[ ok hat location is writable.. [ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done. [ ok . [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables...done. [ ok ] Initializing random number generator...done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5 Copyright 2004-2016 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/52:3b:20:9c:11:51 Sending on LPF/eth0/52:3b:20:9c:11:51 Sending on Socket/fallback DHCPREQUEST of 192.168.1.95 on eth0 to 255.255.255.255 port 67 [ 38.611621] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 44.961320] NET: Registered protocol family 10 [ 44.969824] Segment Routing with IPv6 DHCPREQUEST of 192.168.1.95 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.1.95 from 192.168.1.254 bound to 192.168.1.95 -- renewal in 33090 seconds. done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1334 (syslogd) . ok [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [ ok ] Starting NFS common utilities: statd idmapd. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1337 (klogd) . ok [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Running local boot scripts (/etc/rc.local). Debian GNU/Linux 9 debian ttyS0 debian login: [ 103.285643] random: crng init done
Please post the log of your execution of step 6 and 7 for review, before doing step 8.
root@debian:~# fw_printenv Warning: Bad CRC, using default environment bootargs= bootcmd= bootdelay=2 baudrate=115200 arch=sandbox cpu=sandbox board=sandbox board_name=sandbox stdin=serial,cros-ec-keyb,usbkbd stdout=serial,vidconsole stderr=serial,vidconsole ethaddr=00:00:11:22:33:44 eth1addr=00:00:11:22:33:45 eth3addr=00:00:11:22:33:46 eth5addr=00:00:11:22:33:47 ipaddr=1.2.3.4 host_boot=if host dev ${devnum}; then setenv devtype host; run scan_dev_for_boot_part; fi boot_net_pci_enum=pci enum boot_net_usb_start=usb start usb_boot=usb start; if usb dev ${devnum}; then setenv devtype usb; run scan_dev_for_boot_part; fi boot_prefixes=/ /boot/ boot_scripts=boot.scr.uimg boot.scr boot_script_dhcp=boot.scr.uimg boot_targets=host1 host0 boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}extlinux/extlinux.conf scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}extlinux/extlinux.conf; then echo Found ${prefix}extlinux/extlinux.conf; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr} scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done; scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done bootcmd_host1=setenv devnum 1; run host_boot bootcmd_host0=setenv devnum 0; run host_boot distro_bootcmd=for target in ${boot_targets}; do run bootcmd_${target}; done bootm_size=0x10000000 kernel_addr_r=0x1000000 fdt_addr_r=0xc00000 ramdisk_addr_r=0x2000000 scriptaddr=0x1000 pxefile_addr_r=0x2000 root@debian:~#
Pogov4> printenv arcNumber=3960 baudrate=115200 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm$load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb console=ttyS0,115200 device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-pogoplug_v4 ethact=egiga0 ethaddr=52:3b:20:9c:11:51 if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15 Environment size: 2907/131068 bytes Pogov4>
arcNumber=3960 bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 ethact=egiga0 ethaddr=00:25:31:04:de:09 if_netconsole=ping $serverip ipaddr=192.168.1.231 led_error=orange blinking led_exit=green off led_init=green blinking dtb_file=/boot/dts/kirkwood-pogoplug_v4.dtb load_dtb_addr=0x1c00000 load_initrd_addr=0x1100000 load_uimage_addr=0x800000 load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage machid=f78 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.1.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi usb_ready_retry=15
Re: Need help/advice on brand new pogoplugV4 November 03, 2017 11:28PM |
Admin Registered: 13 years ago Posts: 18,564 |
Quote
> Please post the log of your execution of step 6
> and 7 for review, before doing step 8.
>
> I understood from that to do all the steps from 1
> to 7 before rebooting so I did not made step 8
> (flashing default envs)
Quote
> The box boots fine but the envs seem messed.
Quote
> Warning: Bad CRC, using default environment
arcNumber=3960 bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 ethact=egiga0 ethaddr=00:25:31:04:de:09 if_netconsole=ping $serverip ipaddr=192.168.1.231 led_error=orange blinking led_exit=green off led_init=green blinking dtb_file=/boot/dts/kirkwood-pogoplug_v4.dtb load_dtb_addr=0x1c00000 load_initrd_addr=0x1100000 load_uimage_addr=0x800000 load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage machid=f78 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root) partition=nand0,2 preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.1.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi usb_ready_retry=15
run bootcmd_uenvand list the envs for sanity
printenvlook at these envs to make sure they are what you expected, and then
saveenv
boot
Re: Need help/advice on brand new pogoplugV4 November 04, 2017 10:17AM |
Registered: 6 years ago Posts: 8 |
Re: Need help/advice on brand new pogoplugV4 November 04, 2017 03:36PM |
Admin Registered: 13 years ago Posts: 18,564 |