Welcome! Log In Create A New Profile

Advanced

Need a rootfs with Kernel 3.17

Posted by dippes 
Need a rootfs with Kernel 3.17
January 02, 2018 04:57AM
Hello

I have a Pogoplug (POGO-P24) and sadly to say my stick with Kernel 3.17 are damaged, at this moment I have only a rootfs with Kernel 2.6.31.14_0x820_10_Shv.P21.
Is there any available complete rootfs with Kernal 3.17 or higher what boot with U-Boot 2013.10-tld-3 (May 15 2014 - 14:54:14) for OXNAS?



U-Boot 2013.10-tld-3 (May 15 2014 - 14:54:14) for OXNAS

DRAM: 128 MiB
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
** No partition table - usb 0 **
** No partition table - usb 0 **
Wrong Image Format for bootm command

Led: ORANGE (Failed)
ERROR: can't get kernel image!
stopping USB..
resetting ...

U-Boot SPL 2013.10 (Apr 27 2014 - 19:08:27)
Boot device: NAND
Attempting to set PLLA to 800 MHz ...
plla_ctrl0 : 0000030a
plla_ctrl1 : 00400000
plla_ctrl2 : 007f0068
plla_ctrl3 : 00000193

PLLA Set
Re: Need a rootfs with Kernel 3.17
January 02, 2018 05:00AM
Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2

https://forum.doozan.com/read.php?2,16044

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Need a rootfs with Kernel 3.17
January 05, 2018 03:40AM
Hello,
the device don`t like to boot with
Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2
Debian-3.17.0-oxnas-tld-1-rootfs-bodhi.tar.bz2

Have you any idea?


U-Boot 2013.10-tld-3 (May 15 2014 - 14:54:14) for OXNAS

DRAM:  128 MiB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   
Led:\0x09GREEN
mii0
Main Loop
Hit any key to stop autoboot: 10 \0x08\0x08\0x08 9 \0x08\0x08\0x08 8 \0x08\0x08\0x08 7 \0x08\0x08\0x08 6 \0x08\0x08\0x08 5 \0x08\0x08\0x08 4 \0x08\0x08\0x08 3 \0x08\0x08\0x08 2 \0x08\0x08\0x08 1 \0x08\0x08\0x08 0 
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
** File not found /boot/uImage **
** File not found /boot/uInitrd **
Wrong Image Format for bootm command

Led:\0x09ORANGE (Failed)

/boot

-rw-r--r-- 1 root root   98866 Okt 26  2014 config-3.17.0-oxnas-tld-1
drwxr-xr-x 2 root root    4096 Nov  1  2014 dts
-rw-r--r-- 1 root root 1953748 Nov  1  2014 initrd.img-3.17.0-oxnas-tld-1
-rw-r--r-- 1 root root 1519590 Okt 26  2014 System.map-3.17.0-oxnas-tld-1
-rw-r--r-- 1 root root 4102704 Nov  1  2014 uImage
-rw-r--r-- 1 root root 1953812 Nov  1  2014 uInitrd
-rwxr-xr-x 1 root root 4102640 Okt 26  2014 vmlinuz-3.17.0-oxnas-tld-1
-rwxr-xr-x 1 root root 4102640 Okt 26  2014 zImage-3.17.0-oxnas-tld-1



Edited 1 time(s). Last edit at 01/05/2018 04:44AM by dippes.
Re: Need a rootfs with Kernel 3.17
January 05, 2018 03:42AM
dippes,

Quote

> /etc/boot
>
>
> -rw-r--r-- 1 root root   98866 Okt 26  2014
> config-3.17.0-oxnas-tld-1
> drwxr-xr-x 2 root root    4096 Nov  1  2014 dts
> -rw-r--r-- 1 root root 1953748 Nov  1  2014
> initrd.img-3.17.0-oxnas-tld-1
> -rw-r--r-- 1 root root 1519590 Okt 26  2014
> System.map-3.17.0-oxnas-tld-1
> -rw-r--r-- 1 root root 4102704 Nov  1  2014
> uImage
> -rw-r--r-- 1 root root 1953812 Nov  1  2014
> uInitrd
> -rwxr-xr-x 1 root root 4102640 Okt 26  2014
> vmlinuz-3.17.0-oxnas-tld-1
> -rwxr-xr-x 1 root root 4102640 Okt 26  2014
> zImage-3.17.0-oxnas-tld-1
> 

This is the wrong directory. Kernel files should be installed in

/boot

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Need a rootfs with Kernel 3.17
January 05, 2018 04:46AM
Sorry it was my failure

dippest-VirtualBox rootfs # ls -l
insgesamt 84884
drwxr-xr-x  2 root root       4096 Nov  1  2014 bin
drwxr-xr-x  3 root root       4096 Nov  1  2014 boot
-rwxrwx---  1 root vboxsf 86736625 Jan  3 19:00 Debian-3.17.0-oxnas-tld-1-rootfs-bodhi.tar.bz2
drwxr-xr-x  5 root root       4096 Feb 24  2012 dev
drwxr-xr-x 51 root root       4096 Jan  1  1970 etc
drwxr-xr-x  2 root root       4096 Jan 22  2012 home
drwxr-xr-x 11 root root       4096 Mai  9  2014 lib
drwx------  2 root root      16384 Feb 24  2012 lost+found
drwxr-xr-x  2 root root       4096 Feb 24  2012 media
drwxr-xr-x  2 root root       4096 Jan 22  2012 mnt
drwxr-xr-x  2 root root       4096 Feb 24  2012 opt
drwxr-xr-x  2 root root       4096 Jan 22  2012 proc
drwx------  4 root root       4096 Nov  1  2014 root
drwxr-xr-x  2 root root       4096 Feb  8  2013 run
drwxr-xr-x  2 root root       4096 Mai  9  2014 sbin
drwxr-xr-x  2 root root       4096 Jul 21  2010 selinux
drwxr-xr-x  2 root root       4096 Feb 24  2012 srv
drwxr-xr-x  2 root root       4096 Jan  1  2011 sys
drwxrwxrwt  2 root root       4096 Jan  1  1970 tmp
drwxr-xr-x 10 root root       4096 Feb 24  2012 usr
drwxr-xr-x 11 root root       4096 Jan  1  1970 var
l



Edited 1 time(s). Last edit at 01/05/2018 05:45AM by dippes.
Re: Need a rootfs with Kernel 3.17
January 05, 2018 11:19PM
dippes Wrote:
-------------------------------------------------------
> Sorry it was my failure
>
>
> dippest-VirtualBox rootfs # ls -l
> insgesamt 84884
> drwxr-xr-x  2 root root       4096 Nov  1  2014
> bin
> drwxr-xr-x  3 root root       4096 Nov  1  2014
> boot
> -rwxrwx---  1 root vboxsf 86736625 Jan  3 19:00
> Debian-3.17.0-oxnas-tld-1-rootfs-bodhi.tar.bz2
> drwxr-xr-x  5 root root       4096 Feb 24  2012
> dev
> drwxr-xr-x 51 root root       4096 Jan  1  1970
> etc
> drwxr-xr-x  2 root root       4096 Jan 22  2012
> home
> drwxr-xr-x 11 root root       4096 Mai  9  2014
> lib
> drwx------  2 root root      16384 Feb 24  2012
> lost+found
> drwxr-xr-x  2 root root       4096 Feb 24  2012
> media
> drwxr-xr-x  2 root root       4096 Jan 22  2012
> mnt
> drwxr-xr-x  2 root root       4096 Feb 24  2012
> opt
> drwxr-xr-x  2 root root       4096 Jan 22  2012
> proc
> drwx------  4 root root       4096 Nov  1  2014
> root
> drwxr-xr-x  2 root root       4096 Feb  8  2013
> run
> drwxr-xr-x  2 root root       4096 Mai  9  2014
> sbin
> drwxr-xr-x  2 root root       4096 Jul 21  2010
> selinux
> drwxr-xr-x  2 root root       4096 Feb 24  2012
> srv
> drwxr-xr-x  2 root root       4096 Jan  1  2011
> sys
> drwxrwxrwt  2 root root       4096 Jan  1  1970
> tmp
> drwxr-xr-x 10 root root       4096 Feb 24  2012
> usr
> drwxr-xr-x 11 root root       4096 Jan  1  1970
> var
> l
>

So are you OK now?

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Need a rootfs with Kernel 3.17
January 06, 2018 03:31AM
No, my POGO didn't start eventhough I've tried a lot of USB stick, are my POGO damaged? or there is any possible way to rescue it.
Re: Need a rootfs with Kernel 3.17
January 06, 2018 06:43AM
I have tried other Stick but it boots up to this point and then it breaks up. See the attachment below.

\0x08\0x08\0x08 7 \0x08\0x08\0x08 6 \0x08\0x08\0x08 5 \0x08\0x08\0x08 4 \0x08\0x08\0x08 3 \0x08\0x08\0x08 2 \0x08\0x08\0x08 1 \0x08\0x08\0x08 0 
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
4102704 bytes read in 453 ms (8.6 MiB/s)
1953812 bytes read in 326 ms (5.7 MiB/s)
## Booting kernel from Legacy Image at 60500000 ...
   Image Name:   Linux-3.17.0-oxnas-tld-1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4102640 Bytes = 3.9 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 60e00000 ...
   Image Name:   initramfs-3.17.0-oxnas-tld-1
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    1953748 Bytes = 1.9 MiB
   Load Address: 60000000
   Entry Point:  60000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Led:\0x09GREEN

Starting kernel ...

Uncompressing Linux... done, booting the kernel.


Error: unrecognized/unsupported machine ID (r1 = 0x00000480).


Available machine support:


ID (hex)\0x09NAME

ffffffff\0x09PLXTECH NAS782X SoC (Flattened Device Tree)


Please check your kernel config and/or bootloader.


Re: Need a rootfs with Kernel 3.17
January 06, 2018 07:33AM
dippes Wrote:
-------------------------------------------------------
> I have tried other Stick but it boots up to this
> point and then it breaks up. See the attachment
> below.
>
>
> \0x08\0x08\0x08 7 \0x08\0x08\0x08 6
> \0x08\0x08\0x08 5 \0x08\0x08\0x08 4
> \0x08\0x08\0x08 3 \0x08\0x08\0x08 2
> \0x08\0x08\0x08 1 \0x08\0x08\0x08 0 
> (Re)start USB...
> USB0:   USB EHCI 1.00
> scanning bus 0 for devices... 3 USB Device(s)
> found
>        scanning usb for storage devices... 1
> Storage Device(s) found
> 4102704 bytes read in 453 ms (8.6 MiB/s)
> 1953812 bytes read in 326 ms (5.7 MiB/s)
> ## Booting kernel from Legacy Image at 60500000
> ...
>    Image Name:   Linux-3.17.0-oxnas-tld-1
>    Image Type:   ARM Linux Kernel Image
> (uncompressed)
>    Data Size:    4102640 Bytes = 3.9 MiB
>    Load Address: 60008000
>    Entry Point:  60008000
>    Verifying Checksum ... OK
> ## Loading init Ramdisk from Legacy Image at
> 60e00000 ...
>    Image Name:   initramfs-3.17.0-oxnas-tld-1
>    Image Type:   ARM Linux RAMDisk Image (gzip
> compressed)
>    Data Size:    1953748 Bytes = 1.9 MiB
>    Load Address: 60000000
>    Entry Point:  60000000
>    Verifying Checksum ... OK
>    Loading Kernel Image ... OK
> 
> Led:\0x09GREEN
> 
> Starting kernel ...
> 
> Uncompressing Linux... done, booting the kernel.
> 
> 
> Error: unrecognized/unsupported machine ID (r1 =
> 0x00000480).
> 
> 
> Available machine support:
> 
> 
> ID (hex)\0x09NAME
> 
> ffffffff\0x09PLXTECH NAS782X SoC (Flattened Device
> Tree)
> 
> 
> Please check your kernel config and/or
> bootloader.
> 
> 
>

This rootfs seems ok.

Your uboot envs has some problem. Power up, interrupt setial console at count down and

printenv

And please post the entire serial console log here.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Need a rootfs with Kernel 3.17
January 07, 2018 03:55AM
OX820 # printenv
autoload=no
baudrate=115200
bootargs=console=ttyS0,115200n8
bootcmd=run dt_bootcmd_usb
bootdelay=10
console=console=ttyS0,115200n8
dt_bootcmd_usb=usb start; run dt_usb_bootcmd; usb stop; reset
dt_bootm=bootm $uimage_addr $uinitrd_addr
dt_load_dtb=ext2load usb 0:1 $dtb_addr /boot/dts/ox820-pogoplug-pro.dtb
dt_load_initrd=ext2load usb 0:1 $uinitrd_addr /boot/uInitrd
dt_load_uimage=ext2load usb 0:1 $uimage_addr /boot/uImage
dt_usb_boot=run dt_load_uimage; run dt_load_initrd; run dt_bootm
dt_usb_bootcmd=run usb_set_bootargs; run dt_usb_boot
dtb_addr=0x62c00000
ethact=mii0
ethaddr=5e:2b:15:71:ec:b6
if_netconsole=ping $serverip
ipaddr=192.168.0.222
mtdids=nand0=41000000.nand
mtdparts=mtdparts=41000000.nand:14m(boot),-(data)
preboot_nc=run if_netconsole start_netconsole
serverip=192.168.0.220
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; se                                                                                                             tenv stdout nc; setenv stderr nc; version
stderr=serial
stdin=serial
stdout=serial
uimage_addr=0x60500000
uinitrd_addr=0x60e00000
usb_device=0:1
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=/dev/sda1 rootdelay=1                                                                                                             0 rootfstype=ext3

Environment size: 1181/131068 bytes

Re: Need a rootfs with Kernel 3.17
January 08, 2018 09:50AM
Your env settings were messed up, so it does not boot with the basic rootfs 3.17, which has the original uImage in /boot (and the DTB in /boot/dts).


Power up, interrupt serial console and

setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data) earlyprintk=serial'
setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
setenv dt_usb_boot 'run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm'
boot

-bodhi
===========================
Forum Wiki
bodhi's corner



Edited 2 time(s). Last edit at 01/08/2018 09:51AM by bodhi.
Re: Need a rootfs with Kernel 3.17
January 08, 2018 10:31AM
Hello bodhy

with the three lines the device boot until

[    0.281228] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver


Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.17.0-oxnas-tld-1 (root@tldDebian) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 SMP PREEMPT Sat Oct 25 15:59:43 PDT 2014
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Pogoplug Pro
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[    0.000000] Start Ox820 platform
[    0.000000] PERCPU: Embedded 7 pages/cpu @c7ee3000 s6592 r8192 d13888 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data) earlyprintk=serial
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 119844K/131072K available (5686K kernel code, 286K rwdata, 1680K rodata, 174K init, 233K bss, 11228K reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xffe00000   (2048 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff000000   ( 872 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0739db0   (7368 kB)
[    0.000000]       .init : 0xc073a000 - 0xc07659c0   ( 175 kB)
[    0.000000]       .data : 0xc0766000 - 0xc07adb00   ( 287 kB)
[    0.000000]        .bss : 0xc07adb00 - 0xc07e809c   ( 234 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:160
[    0.000017] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 42949670400ns
[    0.008314] Console: colour dummy device 80x30
[    0.012884] Calibrating delay loop... 319.48 BogoMIPS (lpj=1597440)
[    0.062817] pid_max: default: 32768 minimum: 301
[    0.067650] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.074355] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.082342] Initializing cgroup subsys net_cls
[    0.086901] CPU: Testing write buffer coherency: ok
[    0.092280] Setting up static identity map for 0x60567fa0 - 0x60567fd8
[    0.150476] CPU1: Booted secondary processor
[    0.210160] Brought up 2 CPUs
[    0.217530] SMP: Total of 2 processors activated.
[    0.223296] devtmpfs: initialized
[    0.231275] prandom: seed boundary self test passed
[    0.240407] prandom: 100 self tests passed
[    0.244582] pinctrl core: initialized pinctrl subsystem
[    0.252986] NET: Registered protocol family 16
[    0.258068] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.269744] gpio-oxnas 44000000.gpio: at address c8846000
[    0.275558] gpio-oxnas 44100000.gpio: at address c8848000
[    0.281646] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver

U-Boot SPL 2013.10 (Apr 27 2014 - 19:08:27)
  Boot device: NAND
Attempting to set PLLA to 800 MHz ...
  plla_ctrl0 : 0000030a
  plla_ctrl1 : 00400000
  plla_ctrl2 : 007f0068
  plla_ctrl3 : 00000193

PLLA Set


U-Boot 2013.10-tld-3 (May 15 2014 - 14:54:14) for OXNAS

DRAM:  128 MiB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:
Led:    GREEN
mii0
Main Loop
Hit any key to stop autoboot:  0
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
4102704 bytes read in 387 ms (10.1 MiB/s)
1953812 bytes read in 292 ms (6.4 MiB/s)
## Booting kernel from Legacy Image at 60500000 ...
   Image Name:   Linux-3.17.0-oxnas-tld-1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4102640 Bytes = 3.9 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 60e00000 ...
   Image Name:   initramfs-3.17.0-oxnas-tld-1
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    1953748 Bytes = 1.9 MiB
   Load Address: 60000000
   Entry Point:  60000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Led:    GREEN

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

Error: unrecognized/unsupported machine ID (r1 = 0x00000480).

Available machine support:

ID (hex)        NAME
ffffffff        PLXTECH NAS782X SoC (Flattened Device Tree)

Please check your kernel config and/or bootloader.

U-Boot SPL 2013.10 (Apr 27 2014 - 19:08:27)
  Boot device: NAND
Attempting to set PLLA to 800 MHz ...
  plla_ctrl0 : 0000030a
  plla_ctrl1 : 00400000
  plla_ctrl2 : 007f0068
  plla_ctrl3 : 00000193

PLLA Set


U-Boot 2013.10-tld-3 (May 15 2014 - 14:54:14) for OXNAS

DRAM:  128 MiB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:
Led:    GREEN
mii0
Main Loop
Hit any key to stop autoboot:  0
OX820 # setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data) earlyprintk=serial'
OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
OX820 # setenv dt_usb_boot 'run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm'
OX820 # boot
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
4102704 bytes read in 387 ms (10.1 MiB/s)
1953812 bytes read in 292 ms (6.4 MiB/s)
7029 bytes read in 237 ms (28.3 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
   Image Name:   Linux-3.17.0-oxnas-tld-1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4102640 Bytes = 3.9 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 60e00000 ...
   Image Name:   initramfs-3.17.0-oxnas-tld-1
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    1953748 Bytes = 1.9 MiB
   Load Address: 60000000
   Entry Point:  60000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
   Booting using the fdt blob at 0x62c00000
   Loading Kernel Image ... OK
   Loading Ramdisk to 67c4d000, end 67e29fd4 ... OK
   Loading Device Tree to 67c48000, end 67c4cb74 ... OK

Led:    GREEN

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.17.0-oxnas-tld-1 (root@tldDebian) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 SMP PREEMPT Sat Oct 25 15:59:43 PDT 2014
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Pogoplug Pro
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[    0.000000] Start Ox820 platform
[    0.000000] PERCPU: Embedded 7 pages/cpu @c7ee3000 s6592 r8192 d13888 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data) earlyprintk=serial
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 119844K/131072K available (5686K kernel code, 286K rwdata, 1680K rodata, 174K init, 233K bss, 11228K reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xffe00000   (2048 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff000000   ( 872 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0739db0   (7368 kB)
[    0.000000]       .init : 0xc073a000 - 0xc07659c0   ( 175 kB)
[    0.000000]       .data : 0xc0766000 - 0xc07adb00   ( 287 kB)
[    0.000000]        .bss : 0xc07adb00 - 0xc07e809c   ( 234 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:160
[    0.000017] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 42949670400ns
[    0.008312] Console: colour dummy device 80x30
[    0.012884] Calibrating delay loop... 319.48 BogoMIPS (lpj=1597440)
[    0.062819] pid_max: default: 32768 minimum: 301
[    0.067642] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.074342] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.082344] Initializing cgroup subsys net_cls
[    0.086901] CPU: Testing write buffer coherency: ok
[    0.092282] Setting up static identity map for 0x60567fa0 - 0x60567fd8
[    0.150481] CPU1: Booted secondary processor
[    0.210160] Brought up 2 CPUs
[    0.217528] SMP: Total of 2 processors activated.
[    0.223290] devtmpfs: initialized
[    0.231057] prandom: seed boundary self test passed
[    0.240192] prandom: 100 self tests passed
[    0.244372] pinctrl core: initialized pinctrl subsystem
[    0.252733] NET: Registered protocol family 16
[    0.257815] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.269329] gpio-oxnas 44000000.gpio: at address c8846000
[    0.275138] gpio-oxnas 44100000.gpio: at address c8848000
[    0.281228] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver

Re: Need a rootfs with Kernel 3.17
January 08, 2018 10:42AM
dippes,

Let's take out the mtdparts.

setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial'
setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
setenv dt_usb_boot 'run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm'
boot

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Need a rootfs with Kernel 3.17
January 08, 2018 11:42AM
bodhi,

the same

stop

[ 0.281049] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
Re: Need a rootfs with Kernel 3.17
January 08, 2018 10:30PM
dippes,

1. Use another USB thumb drive and create a new rootfs using Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2.

Quote

Updated 02 Aug 2017:

Rootfs Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2 was uploaded.

Basic Debian stretch Oxnas rootfs for Popo Pro/Classic V3 plug:

- tarball size: 180M
- install size: 477M
- Installed packages: nano, avahi, ntp, busybox-syslogd (log to RAM), htop, dialog, bz2, iperf, ethtool, sysvinit-core, sysvinit, sysvinit-utils, mtd-utils.
- see LED controls in /etc/rc.local, and /etc/rc0.d/K08halt
- see some useful aliases in /root/.profile
- root password: root

2. Boot with this new rootfs.

Power up, interrupt serial console and

setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data) earlyprintk=serial'
setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
setenv dt_usb_boot 'run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm'
boot

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Need a rootfs with Kernel 3.17
January 09, 2018 09:58AM
hello bodhi,

With rootfs "Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2" the same.

stop by

[ 0.371230] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver

also without the mtdparts
Re: Need a rootfs with Kernel 3.17
January 09, 2018 10:54AM
dippes,

Please post the entire log of the terminal session when you create the rootfs usingDebian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2.

I think there is something went wrong when you did that. Just copy and paste the terminal log of how you create the partition, and format with ext3, and untar the rootfs tarball. Perhaps I will be able to spot something that was incorrect.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Need a rootfs with Kernel 3.17
January 09, 2018 01:19PM
root@HP-Server / > fdisk /dev/sdc

Befehl (m für Hilfe): o
Building a new DOS disklabel with disk identifier 0x3854c2be.
Changes will remain in memory only, until you decide to write them.
After that, of course, the previous content won't be recoverable.

Warnung: Schreiben wird ungültiges Flag 0x0000 in Part.-tabelle 4 korrigieren

Befehl (m für Hilfe): n
Partition type:
   p   primary (0 primary, 0 extended, 4 free)
   e   extended
Select (default p): p
Partitionsnummer (1-4, Vorgabe: 1): 1
Erster Sektor (2048-15633407, Vorgabe: 2048):
Benutze den Standardwert 2048
Last Sektor, +Sektoren or +size{K,M,G} (2048-15633407, Vorgabe: 15633407):
Benutze den Standardwert 15633407

Befehl (m für Hilfe): w
Die Partitionstabelle wurde verändert!

Rufe ioctl() um Partitionstabelle neu einzulesen.
Synchronisiere Platten.

root@HP-Server / > mkfs.ext3 /dev/sdc1
mke2fs 1.42.9 (4-Feb-2014)
Dateisystem-Label=
OS-Typ: Linux
Blockgröße=4096 (log=2)
Fragmentgröße=4096 (log=2)
Stride=0 Blöcke, Stripebreite=0 Blöcke
488640 Inodes, 1953920 Blöcke
97696 Blöcke (5.00%) reserviert für den Superuser
Erster Datenblock=0
Maximale Dateisystem-Blöcke=2004877312
60 Blockgruppen
32768 Blöcke pro Gruppe, 32768 Fragmente pro Gruppe
8144 Inodes pro Gruppe
Superblock-Sicherungskopien gespeichert in den Blöcken:
        32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632

Platz für Gruppentabellen wird angefordert: erledigt
Inode-Tabellen werden geschrieben: erledigt
Erstelle Journal (32768 Blöcke): erledigt
Schreibe Superblöcke und Dateisystem-Accountinginformationen: erledigt

root@HP-Server / > e2label /dev/sdc1 rootfs

root@HP-Server /media/stick > ls
Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2  lost+found

 /media/stick > tar xvjf Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2
Re: Need a rootfs with Kernel 3.17
January 10, 2018 12:06PM
dippes,

Are you root at this point?

/media/stick > tar xvjf Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2


It you were root, then all the steps look good. If you were not, then redo the above step.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Need a rootfs with Kernel 3.17
January 10, 2018 12:12PM
this is the mountpoint from the usb stick in my Linuxmachine

root@HP-Server ~ > mount -t ext3 /dev/sdc1 /media/stick
root@HP-Server /media/stick > ls -l
insgesamt 184052
drwxr-xr-x  2 root root      4096 Aug  1 10:36 bin
drwxr-xr-x  3 root root      4096 Aug  2 10:29 boot
-rw-r-----  1 root root 188188318 Jan 10 17:14 Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2
drwxr-xr-x  5 root root      4096 Feb 24  2012 dev
drwxr-xr-x 61 root root      4096 Jan  1  1970 etc
drwxr-xr-x  2 root root      4096 Jan 22  2012 home
drwxr-xr-x 13 root root      4096 Aug  1 07:38 lib
drwx------  2 root root     16384 Feb 24  2012 lost+found
drwxr-xr-x  2 root root      4096 Feb 24  2012 media
drwxr-xr-x  2 root root      4096 Aug  1 07:23 mnt
drwxr-xr-x  2 root root      4096 Feb 24  2012 opt
drwxr-xr-x  2 root root      4096 Jan 22  2012 proc
drwx------  5 root root      4096 Aug  2 02:19 root
drwxr-xr-x  2 root root      4096 Feb  8  2013 run
drwxr-xr-x  2 root root      4096 Aug  1 10:21 sbin
drwxr-xr-x  2 root root      4096 Feb 24  2012 srv
drwxr-xr-x  2 root root      4096 Jan  1  2011 sys
drwxrwxrwt  2 root root      4096 Jan  1  1970 tmp
drwxr-xr-x 10 root root      4096 Feb 24  2012 usr
drwxr-xr-x 11 root root      4096 Jan  1  1970 var

Quote
bodhi
Are you root at this point?
yes



Edited 2 time(s). Last edit at 01/10/2018 12:23PM by dippes.
Re: Need a rootfs with Kernel 3.17
January 10, 2018 10:31PM
dippes,

This is a strange problem. The behavior as though the DTB was corrupted.

We could try to flash the latest u-boot for this box (uboot.2015.10-tld-2) in serial console to see if it helps. But even with new u-boot, it might not boot pass that point.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Need a rootfs with Kernel 3.17
January 11, 2018 08:00AM
What type of USB drive are you using? USB 2.0, 3.0, model, brand ...

lsusb -vvv


You could try to recreate the rootfs using a different USB stick. Prefereably USB 2.0, Sandisk brand.

-bodhi
===========================
Forum Wiki
bodhi's corner



Edited 1 time(s). Last edit at 01/11/2018 08:06AM by bodhi.
Re: Need a rootfs with Kernel 3.17
January 11, 2018 09:58AM
Hello bodhi
i use SanDisk Cruzer 8 GB stick and try 3 different USB drives.
Bevor my Pogo crashed all my USB Sticks working fine.

us 001 Device 105: ID 0781:5567 SanDisk Corp. Cruzer Blade
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  idVendor           0x0781 SanDisk Corp.
  idProduct          0x5567 Cruzer Blade
  bcdDevice            1.26
  iManufacturer           1 SanDisk
  iProduct                2 Cruzer Blade
  iSerial                 3 4C532000030318123381
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           32
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0x80
      (Bus Powered)
    MaxPower              200mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass         8 Mass Storage
      bInterfaceSubClass      6 SCSI
      bInterfaceProtocol     80 Bulk-Only
      iInterface              0 
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               1
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0000
  (Bus Powered)
Re: Need a rootfs with Kernel 3.17
January 11, 2018 11:00PM
dippes,

Boot with the rootfs Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2 on USB.

And post the entire serial console log here (from u-boot banner until it stucks or reset). I'd like to see what happens after this line

[    0.281228] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Need a rootfs with Kernel 3.17
January 12, 2018 05:19AM
with

setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data) earlyprintk=serial'
setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
setenv dt_usb_boot 'run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm'
U-Boot SPL 2013.10 (Apr 27 2014 - 19:08:27)
  Boot device: NAND
Attempting to set PLLA to 800 MHz ...
  plla_ctrl0 : 0000030a
  plla_ctrl1 : 00400000
  plla_ctrl2 : 007f0068
  plla_ctrl3 : 00000193

PLLA Set


U-Boot 2013.10-tld-3 (May 15 2014 - 14:54:14) for OXNAS

DRAM:  128 MiB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:
Led:    GREEN
mii0
Main Loop
Hit any key to stop autoboot:  0
OX820 # setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data) earlyprintk=serial'
OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
OX820 # setenv dt_usb_boot 'run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm'
OX820 # boot
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
4621824 bytes read in 388 ms (11.4 MiB/s)
4594376 bytes read in 359 ms (12.2 MiB/s)
7067 bytes read in 205 ms (33.2 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
   Image Name:   Linux-4.4.54-oxnas-tld-1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4621760 Bytes = 4.4 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 60e00000 ...
   Image Name:   initramfs-4.4.54-oxnas-tld-1
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    4594312 Bytes = 4.4 MiB
   Load Address: 60000000
   Entry Point:  60000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
   Booting using the fdt blob at 0x62c00000
   Loading Kernel Image ... OK
   Loading Ramdisk to 679c8000, end 67e29a88 ... OK
   Loading Device Tree to 679c3000, end 679c7b9a ... OK

Led:    GREEN

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.4.54-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Pogoplug V3 Pro
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[    0.000000] PERCPU: Embedded 12 pages/cpu @c7eda000 s17696 r8192 d23264 u49152
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data) earlyprintk=serial
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 116204K/131072K available (6410K kernel code, 288K rwdata, 1908K rodata, 224K init, 247K bss, 14868K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0827e14   (8320 kB)
[    0.000000]       .init : 0xc0828000 - 0xc0860000   ( 224 kB)
[    0.000000]       .data : 0xc0860000 - 0xc08a8378   ( 289 kB)
[    0.000000]        .bss : 0xc08a8378 - 0xc08e6350   ( 248 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:160
[    0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[    0.000007] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[    0.008337] Console: colour dummy device 80x30
[    0.012897] Calibrating delay loop... 319.48 BogoMIPS (lpj=1597440)
[    0.062594] pid_max: default: 32768 minimum: 301
[    0.067435] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.074140] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.082106] Initializing cgroup subsys net_cls
[    0.086686] CPU: Testing write buffer coherency: ok
[    0.092108] Setting up static identity map for 0x60008220 - 0x60008258
[    0.229952] Brought up 2 CPUs
[    0.233000] SMP: Total of 2 processors activated (638.97 BogoMIPS).
[    0.240199] devtmpfs: initialized
[    0.249364] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.259317] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.265838] prandom: seed boundary self test passed
[    0.275432] prandom: 100 self tests passed
[    0.279605] pinctrl core: initialized pinctrl subsystem
[    0.285788] NET: Registered protocol family 16
[    0.290951] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.319818] cpuidle: using governor ladder
[    0.349816] cpuidle: using governor menu
[    0.359255] gpio-oxnas 44000000.gpio: at address c8848000
[    0.365186] gpio-oxnas 44100000.gpio: at address c884a000
[    0.371297] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver

without

U-Boot SPL 2013.10 (Apr 27 2014 - 19:08:27)
  Boot device: NAND
Attempting to set PLLA to 800 MHz ...
  plla_ctrl0 : 0000030a
  plla_ctrl1 : 00400000
  plla_ctrl2 : 007f0068
  plla_ctrl3 : 00000193

PLLA Set


U-Boot 2013.10-tld-3 (May 15 2014 - 14:54:14) for OXNAS

DRAM:  128 MiB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:
Led:    GREEN
mii0
Main Loop
Hit any key to stop autoboot:  0
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
4621824 bytes read in 388 ms (11.4 MiB/s)
4594376 bytes read in 359 ms (12.2 MiB/s)
## Booting kernel from Legacy Image at 60500000 ...
   Image Name:   Linux-4.4.54-oxnas-tld-1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4621760 Bytes = 4.4 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 60e00000 ...
   Image Name:   initramfs-4.4.54-oxnas-tld-1
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    4594312 Bytes = 4.4 MiB
   Load Address: 60000000
   Entry Point:  60000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Led:    GREEN

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

Error: unrecognized/unsupported machine ID (r1 = 0x00000480).

Available machine support:

ID (hex)        NAME
ffffffff        PLXTECH NAS782X SoC (Flattened Device Tree)

Please check your kernel config and/or bootloader.

Re: Need a rootfs with Kernel 3.17
January 12, 2018 08:46AM
dippes,

I think I've totally missed the fact that you have the POGO-P24, I thought you have the Pogo Pro :) (too many things that has been distracted my thinking). This box no Wifi card! So please try this new envs set with the rootfs Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2 .


setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data) earlyprintk=serial'
setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
setenv dt_usb_boot 'run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm'
setenv dt_load_dtb 'ext2load usb 0:1 $dtb_addr /boot/dts/ox820-pogoplug-classic.dtb'

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Need a rootfs with Kernel 3.17
January 13, 2018 02:42AM
Its really a Pogoplug-Pro.With the 4 lines the device running.But afte the reboot i need to refresh the lines.

How can you saved it permanently?

setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data) earlyprintk=serial'
setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
setenv dt_usb_boot 'run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm'
setenv dt_load_dtb 'ext2load usb 0:1 $dtb_addr /boot/dts/ox820-pogoplug-classic.dtb'
Attachments:
open | download - Pogoplug-Pro.jpg (227.5 KB)
Re: Need a rootfs with Kernel 3.17
January 13, 2018 02:59AM
dippes,

> Its really a Pogoplug-Pro.With the 4 lines the
> device running.

It is not a Pogoplug Pro V3. it is a Pogoplug Classic V3. The difference is Wifi PCIe card (Pro version has it, Classic version does not).

Please post the entire serial console booting log.

-bodhi
===========================
Forum Wiki
bodhi's corner
Re: Need a rootfs with Kernel 3.17
January 13, 2018 11:19AM
Re: Need a rootfs with Kernel 3.17
January 13, 2018 11:32AM
dippes,

Cool! glad it is working well for you finally.

-bodhi
===========================
Forum Wiki
bodhi's corner
Author:

Your Email:


Subject:


Spam prevention:
Please, solve the mathematical question and enter the answer in the input field below. This is for blocking bots that try to post this form automatically.
Question: how much is 12 plus 14?
Message: