Need a rootfs with Kernel 3.17
Posted by dippes
|
Need a rootfs with Kernel 3.17 January 02, 2018 05:57AM |
Registered: 6 years ago Posts: 17 |
Hello
I have a Pogoplug (POGO-P24) and sadly to say my stick with Kernel 3.17 are damaged, at this moment I have only a rootfs with Kernel 2.6.31.14_0x820_10_Shv.P21.
Is there any available complete rootfs with Kernal 3.17 or higher what boot with U-Boot 2013.10-tld-3 (May 15 2014 - 14:54:14) for OXNAS?
I have a Pogoplug (POGO-P24) and sadly to say my stick with Kernel 3.17 are damaged, at this moment I have only a rootfs with Kernel 2.6.31.14_0x820_10_Shv.P21.
Is there any available complete rootfs with Kernal 3.17 or higher what boot with U-Boot 2013.10-tld-3 (May 15 2014 - 14:54:14) for OXNAS?
U-Boot 2013.10-tld-3 (May 15 2014 - 14:54:14) for OXNAS DRAM: 128 MiB NAND: 128 MiB In: serial Out: serial Err: serial Net: Led: GREEN mii0 Main Loop Hit any key to stop autoboot: 0 (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found ** No partition table - usb 0 ** ** No partition table - usb 0 ** Wrong Image Format for bootm command Led: ORANGE (Failed) ERROR: can't get kernel image! stopping USB.. resetting ... U-Boot SPL 2013.10 (Apr 27 2014 - 19:08:27) Boot device: NAND Attempting to set PLLA to 800 MHz ... plla_ctrl0 : 0000030a plla_ctrl1 : 00400000 plla_ctrl2 : 007f0068 plla_ctrl3 : 00000193 PLLA Set
|
Re: Need a rootfs with Kernel 3.17 January 02, 2018 06:00AM |
Admin Registered: 13 years ago Posts: 18,550 |
Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2
https://forum.doozan.com/read.php?2,16044
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
https://forum.doozan.com/read.php?2,16044
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Need a rootfs with Kernel 3.17 January 05, 2018 04:40AM |
Registered: 6 years ago Posts: 17 |
Hello,
the device don`t like to boot with
Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2
Debian-3.17.0-oxnas-tld-1-rootfs-bodhi.tar.bz2
Have you any idea?
/boot
Edited 1 time(s). Last edit at 01/05/2018 05:44AM by dippes.
the device don`t like to boot with
Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2
Debian-3.17.0-oxnas-tld-1-rootfs-bodhi.tar.bz2
Have you any idea?
U-Boot 2013.10-tld-3 (May 15 2014 - 14:54:14) for OXNAS
DRAM: 128 MiB
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net:
Led:\0x09GREEN
mii0
Main Loop
Hit any key to stop autoboot: 10 \0x08\0x08\0x08 9 \0x08\0x08\0x08 8 \0x08\0x08\0x08 7 \0x08\0x08\0x08 6 \0x08\0x08\0x08 5 \0x08\0x08\0x08 4 \0x08\0x08\0x08 3 \0x08\0x08\0x08 2 \0x08\0x08\0x08 1 \0x08\0x08\0x08 0
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
** File not found /boot/uImage **
** File not found /boot/uInitrd **
Wrong Image Format for bootm command
Led:\0x09ORANGE (Failed)
/boot
-rw-r--r-- 1 root root 98866 Okt 26 2014 config-3.17.0-oxnas-tld-1 drwxr-xr-x 2 root root 4096 Nov 1 2014 dts -rw-r--r-- 1 root root 1953748 Nov 1 2014 initrd.img-3.17.0-oxnas-tld-1 -rw-r--r-- 1 root root 1519590 Okt 26 2014 System.map-3.17.0-oxnas-tld-1 -rw-r--r-- 1 root root 4102704 Nov 1 2014 uImage -rw-r--r-- 1 root root 1953812 Nov 1 2014 uInitrd -rwxr-xr-x 1 root root 4102640 Okt 26 2014 vmlinuz-3.17.0-oxnas-tld-1 -rwxr-xr-x 1 root root 4102640 Okt 26 2014 zImage-3.17.0-oxnas-tld-1
Edited 1 time(s). Last edit at 01/05/2018 05:44AM by dippes.
|
Re: Need a rootfs with Kernel 3.17 January 05, 2018 04:42AM |
Admin Registered: 13 years ago Posts: 18,550 |
dippes,
This is the wrong directory. Kernel files should be installed in
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Quote
> /etc/boot
>
>> -rw-r--r-- 1 root root 98866 Okt 26 2014 > config-3.17.0-oxnas-tld-1 > drwxr-xr-x 2 root root 4096 Nov 1 2014 dts > -rw-r--r-- 1 root root 1953748 Nov 1 2014 > initrd.img-3.17.0-oxnas-tld-1 > -rw-r--r-- 1 root root 1519590 Okt 26 2014 > System.map-3.17.0-oxnas-tld-1 > -rw-r--r-- 1 root root 4102704 Nov 1 2014 > uImage > -rw-r--r-- 1 root root 1953812 Nov 1 2014 > uInitrd > -rwxr-xr-x 1 root root 4102640 Okt 26 2014 > vmlinuz-3.17.0-oxnas-tld-1 > -rwxr-xr-x 1 root root 4102640 Okt 26 2014 > zImage-3.17.0-oxnas-tld-1 >
This is the wrong directory. Kernel files should be installed in
/boot
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Need a rootfs with Kernel 3.17 January 05, 2018 05:46AM |
Registered: 6 years ago Posts: 17 |
Sorry it was my failure
Edited 1 time(s). Last edit at 01/05/2018 06:45AM by dippes.
dippest-VirtualBox rootfs # ls -l insgesamt 84884 drwxr-xr-x 2 root root 4096 Nov 1 2014 bin drwxr-xr-x 3 root root 4096 Nov 1 2014 boot -rwxrwx--- 1 root vboxsf 86736625 Jan 3 19:00 Debian-3.17.0-oxnas-tld-1-rootfs-bodhi.tar.bz2 drwxr-xr-x 5 root root 4096 Feb 24 2012 dev drwxr-xr-x 51 root root 4096 Jan 1 1970 etc drwxr-xr-x 2 root root 4096 Jan 22 2012 home drwxr-xr-x 11 root root 4096 Mai 9 2014 lib drwx------ 2 root root 16384 Feb 24 2012 lost+found drwxr-xr-x 2 root root 4096 Feb 24 2012 media drwxr-xr-x 2 root root 4096 Jan 22 2012 mnt drwxr-xr-x 2 root root 4096 Feb 24 2012 opt drwxr-xr-x 2 root root 4096 Jan 22 2012 proc drwx------ 4 root root 4096 Nov 1 2014 root drwxr-xr-x 2 root root 4096 Feb 8 2013 run drwxr-xr-x 2 root root 4096 Mai 9 2014 sbin drwxr-xr-x 2 root root 4096 Jul 21 2010 selinux drwxr-xr-x 2 root root 4096 Feb 24 2012 srv drwxr-xr-x 2 root root 4096 Jan 1 2011 sys drwxrwxrwt 2 root root 4096 Jan 1 1970 tmp drwxr-xr-x 10 root root 4096 Feb 24 2012 usr drwxr-xr-x 11 root root 4096 Jan 1 1970 var l
Edited 1 time(s). Last edit at 01/05/2018 06:45AM by dippes.
|
Re: Need a rootfs with Kernel 3.17 January 06, 2018 12:19AM |
Admin Registered: 13 years ago Posts: 18,550 |
dippes Wrote:
-------------------------------------------------------
> Sorry it was my failure
>
>
So are you OK now?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> Sorry it was my failure
>
>
> dippest-VirtualBox rootfs # ls -l > insgesamt 84884 > drwxr-xr-x 2 root root 4096 Nov 1 2014 > bin > drwxr-xr-x 3 root root 4096 Nov 1 2014 > boot > -rwxrwx--- 1 root vboxsf 86736625 Jan 3 19:00 > Debian-3.17.0-oxnas-tld-1-rootfs-bodhi.tar.bz2 > drwxr-xr-x 5 root root 4096 Feb 24 2012 > dev > drwxr-xr-x 51 root root 4096 Jan 1 1970 > etc > drwxr-xr-x 2 root root 4096 Jan 22 2012 > home > drwxr-xr-x 11 root root 4096 Mai 9 2014 > lib > drwx------ 2 root root 16384 Feb 24 2012 > lost+found > drwxr-xr-x 2 root root 4096 Feb 24 2012 > media > drwxr-xr-x 2 root root 4096 Jan 22 2012 > mnt > drwxr-xr-x 2 root root 4096 Feb 24 2012 > opt > drwxr-xr-x 2 root root 4096 Jan 22 2012 > proc > drwx------ 4 root root 4096 Nov 1 2014 > root > drwxr-xr-x 2 root root 4096 Feb 8 2013 > run > drwxr-xr-x 2 root root 4096 Mai 9 2014 > sbin > drwxr-xr-x 2 root root 4096 Jul 21 2010 > selinux > drwxr-xr-x 2 root root 4096 Feb 24 2012 > srv > drwxr-xr-x 2 root root 4096 Jan 1 2011 > sys > drwxrwxrwt 2 root root 4096 Jan 1 1970 > tmp > drwxr-xr-x 10 root root 4096 Feb 24 2012 > usr > drwxr-xr-x 11 root root 4096 Jan 1 1970 > var > l >
So are you OK now?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Need a rootfs with Kernel 3.17 January 06, 2018 04:31AM |
Registered: 6 years ago Posts: 17 |
|
Re: Need a rootfs with Kernel 3.17 January 06, 2018 07:43AM |
Registered: 6 years ago Posts: 17 |
I have tried other Stick but it boots up to this point and then it breaks up. See the attachment below.
\0x08\0x08\0x08 7 \0x08\0x08\0x08 6 \0x08\0x08\0x08 5 \0x08\0x08\0x08 4 \0x08\0x08\0x08 3 \0x08\0x08\0x08 2 \0x08\0x08\0x08 1 \0x08\0x08\0x08 0
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
4102704 bytes read in 453 ms (8.6 MiB/s)
1953812 bytes read in 326 ms (5.7 MiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-3.17.0-oxnas-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4102640 Bytes = 3.9 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 60e00000 ...
Image Name: initramfs-3.17.0-oxnas-tld-1
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 1953748 Bytes = 1.9 MiB
Load Address: 60000000
Entry Point: 60000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Led:\0x09GREEN
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Error: unrecognized/unsupported machine ID (r1 = 0x00000480).
Available machine support:
ID (hex)\0x09NAME
ffffffff\0x09PLXTECH NAS782X SoC (Flattened Device Tree)
Please check your kernel config and/or bootloader.
|
Re: Need a rootfs with Kernel 3.17 January 06, 2018 08:33AM |
Admin Registered: 13 years ago Posts: 18,550 |
dippes Wrote:
-------------------------------------------------------
> I have tried other Stick but it boots up to this
> point and then it breaks up. See the attachment
> below.
>
>
This rootfs seems ok.
Your uboot envs has some problem. Power up, interrupt setial console at count down and
And please post the entire serial console log here.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> I have tried other Stick but it boots up to this
> point and then it breaks up. See the attachment
> below.
>
>
> \0x08\0x08\0x08 7 \0x08\0x08\0x08 6 > \0x08\0x08\0x08 5 \0x08\0x08\0x08 4 > \0x08\0x08\0x08 3 \0x08\0x08\0x08 2 > \0x08\0x08\0x08 1 \0x08\0x08\0x08 0 > (Re)start USB... > USB0: USB EHCI 1.00 > scanning bus 0 for devices... 3 USB Device(s) > found > scanning usb for storage devices... 1 > Storage Device(s) found > 4102704 bytes read in 453 ms (8.6 MiB/s) > 1953812 bytes read in 326 ms (5.7 MiB/s) > ## Booting kernel from Legacy Image at 60500000 > ... > Image Name: Linux-3.17.0-oxnas-tld-1 > Image Type: ARM Linux Kernel Image > (uncompressed) > Data Size: 4102640 Bytes = 3.9 MiB > Load Address: 60008000 > Entry Point: 60008000 > Verifying Checksum ... OK > ## Loading init Ramdisk from Legacy Image at > 60e00000 ... > Image Name: initramfs-3.17.0-oxnas-tld-1 > Image Type: ARM Linux RAMDisk Image (gzip > compressed) > Data Size: 1953748 Bytes = 1.9 MiB > Load Address: 60000000 > Entry Point: 60000000 > Verifying Checksum ... OK > Loading Kernel Image ... OK > > Led:\0x09GREEN > > Starting kernel ... > > Uncompressing Linux... done, booting the kernel. > > > Error: unrecognized/unsupported machine ID (r1 = > 0x00000480). > > > Available machine support: > > > ID (hex)\0x09NAME > > ffffffff\0x09PLXTECH NAS782X SoC (Flattened Device > Tree) > > > Please check your kernel config and/or > bootloader. > > >
This rootfs seems ok.
Your uboot envs has some problem. Power up, interrupt setial console at count down and
printenv
And please post the entire serial console log here.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Need a rootfs with Kernel 3.17 January 07, 2018 04:55AM |
Registered: 6 years ago Posts: 17 |
OX820 # printenv autoload=no baudrate=115200 bootargs=console=ttyS0,115200n8 bootcmd=run dt_bootcmd_usb bootdelay=10 console=console=ttyS0,115200n8 dt_bootcmd_usb=usb start; run dt_usb_bootcmd; usb stop; reset dt_bootm=bootm $uimage_addr $uinitrd_addr dt_load_dtb=ext2load usb 0:1 $dtb_addr /boot/dts/ox820-pogoplug-pro.dtb dt_load_initrd=ext2load usb 0:1 $uinitrd_addr /boot/uInitrd dt_load_uimage=ext2load usb 0:1 $uimage_addr /boot/uImage dt_usb_boot=run dt_load_uimage; run dt_load_initrd; run dt_bootm dt_usb_bootcmd=run usb_set_bootargs; run dt_usb_boot dtb_addr=0x62c00000 ethact=mii0 ethaddr=5e:2b:15:71:ec:b6 if_netconsole=ping $serverip ipaddr=192.168.0.222 mtdids=nand0=41000000.nand mtdparts=mtdparts=41000000.nand:14m(boot),-(data) preboot_nc=run if_netconsole start_netconsole serverip=192.168.0.220 start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; se tenv stdout nc; setenv stderr nc; version stderr=serial stdin=serial stdout=serial uimage_addr=0x60500000 uinitrd_addr=0x60e00000 usb_device=0:1 usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=/dev/sda1 rootdelay=1 0 rootfstype=ext3 Environment size: 1181/131068 bytes
|
Re: Need a rootfs with Kernel 3.17 January 08, 2018 10:50AM |
Admin Registered: 13 years ago Posts: 18,550 |
Your env settings were messed up, so it does not boot with the basic rootfs 3.17, which has the original uImage in /boot (and the DTB in /boot/dts).
Power up, interrupt serial console and
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 2 time(s). Last edit at 01/08/2018 10:51AM by bodhi.
Power up, interrupt serial console and
setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data) earlyprintk=serial' setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr' setenv dt_usb_boot 'run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm' boot
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 2 time(s). Last edit at 01/08/2018 10:51AM by bodhi.
|
Re: Need a rootfs with Kernel 3.17 January 08, 2018 11:31AM |
Registered: 6 years ago Posts: 17 |
Hello bodhy
with the three lines the device boot until
with the three lines the device boot until
[ 0.281228] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.17.0-oxnas-tld-1 (root@tldDebian) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 SMP PREEMPT Sat Oct 25 15:59:43 PDT 2014
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Pogoplug Pro
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[ 0.000000] Start Ox820 platform
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c7ee3000 s6592 r8192 d13888 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data) earlyprintk=serial
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 119844K/131072K available (5686K kernel code, 286K rwdata, 1680K rodata, 174K init, 233K bss, 11228K reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0739db0 (7368 kB)
[ 0.000000] .init : 0xc073a000 - 0xc07659c0 ( 175 kB)
[ 0.000000] .data : 0xc0766000 - 0xc07adb00 ( 287 kB)
[ 0.000000] .bss : 0xc07adb00 - 0xc07e809c ( 234 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:160
[ 0.000017] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 42949670400ns
[ 0.008314] Console: colour dummy device 80x30
[ 0.012884] Calibrating delay loop... 319.48 BogoMIPS (lpj=1597440)
[ 0.062817] pid_max: default: 32768 minimum: 301
[ 0.067650] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.074355] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.082342] Initializing cgroup subsys net_cls
[ 0.086901] CPU: Testing write buffer coherency: ok
[ 0.092280] Setting up static identity map for 0x60567fa0 - 0x60567fd8
[ 0.150476] CPU1: Booted secondary processor
[ 0.210160] Brought up 2 CPUs
[ 0.217530] SMP: Total of 2 processors activated.
[ 0.223296] devtmpfs: initialized
[ 0.231275] prandom: seed boundary self test passed
[ 0.240407] prandom: 100 self tests passed
[ 0.244582] pinctrl core: initialized pinctrl subsystem
[ 0.252986] NET: Registered protocol family 16
[ 0.258068] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.269744] gpio-oxnas 44000000.gpio: at address c8846000
[ 0.275558] gpio-oxnas 44100000.gpio: at address c8848000
[ 0.281646] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
U-Boot SPL 2013.10 (Apr 27 2014 - 19:08:27)
Boot device: NAND
Attempting to set PLLA to 800 MHz ...
plla_ctrl0 : 0000030a
plla_ctrl1 : 00400000
plla_ctrl2 : 007f0068
plla_ctrl3 : 00000193
PLLA Set
U-Boot 2013.10-tld-3 (May 15 2014 - 14:54:14) for OXNAS
DRAM: 128 MiB
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
4102704 bytes read in 387 ms (10.1 MiB/s)
1953812 bytes read in 292 ms (6.4 MiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-3.17.0-oxnas-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4102640 Bytes = 3.9 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 60e00000 ...
Image Name: initramfs-3.17.0-oxnas-tld-1
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 1953748 Bytes = 1.9 MiB
Load Address: 60000000
Entry Point: 60000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Led: GREEN
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Error: unrecognized/unsupported machine ID (r1 = 0x00000480).
Available machine support:
ID (hex) NAME
ffffffff PLXTECH NAS782X SoC (Flattened Device Tree)
Please check your kernel config and/or bootloader.
U-Boot SPL 2013.10 (Apr 27 2014 - 19:08:27)
Boot device: NAND
Attempting to set PLLA to 800 MHz ...
plla_ctrl0 : 0000030a
plla_ctrl1 : 00400000
plla_ctrl2 : 007f0068
plla_ctrl3 : 00000193
PLLA Set
U-Boot 2013.10-tld-3 (May 15 2014 - 14:54:14) for OXNAS
DRAM: 128 MiB
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0
OX820 # setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data) earlyprintk=serial'
OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
OX820 # setenv dt_usb_boot 'run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm'
OX820 # boot
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
4102704 bytes read in 387 ms (10.1 MiB/s)
1953812 bytes read in 292 ms (6.4 MiB/s)
7029 bytes read in 237 ms (28.3 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-3.17.0-oxnas-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4102640 Bytes = 3.9 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 60e00000 ...
Image Name: initramfs-3.17.0-oxnas-tld-1
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 1953748 Bytes = 1.9 MiB
Load Address: 60000000
Entry Point: 60000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
Booting using the fdt blob at 0x62c00000
Loading Kernel Image ... OK
Loading Ramdisk to 67c4d000, end 67e29fd4 ... OK
Loading Device Tree to 67c48000, end 67c4cb74 ... OK
Led: GREEN
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.17.0-oxnas-tld-1 (root@tldDebian) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 SMP PREEMPT Sat Oct 25 15:59:43 PDT 2014
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Pogoplug Pro
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[ 0.000000] Start Ox820 platform
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c7ee3000 s6592 r8192 d13888 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data) earlyprintk=serial
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 119844K/131072K available (5686K kernel code, 286K rwdata, 1680K rodata, 174K init, 233K bss, 11228K reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0739db0 (7368 kB)
[ 0.000000] .init : 0xc073a000 - 0xc07659c0 ( 175 kB)
[ 0.000000] .data : 0xc0766000 - 0xc07adb00 ( 287 kB)
[ 0.000000] .bss : 0xc07adb00 - 0xc07e809c ( 234 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:160
[ 0.000017] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 42949670400ns
[ 0.008312] Console: colour dummy device 80x30
[ 0.012884] Calibrating delay loop... 319.48 BogoMIPS (lpj=1597440)
[ 0.062819] pid_max: default: 32768 minimum: 301
[ 0.067642] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.074342] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.082344] Initializing cgroup subsys net_cls
[ 0.086901] CPU: Testing write buffer coherency: ok
[ 0.092282] Setting up static identity map for 0x60567fa0 - 0x60567fd8
[ 0.150481] CPU1: Booted secondary processor
[ 0.210160] Brought up 2 CPUs
[ 0.217528] SMP: Total of 2 processors activated.
[ 0.223290] devtmpfs: initialized
[ 0.231057] prandom: seed boundary self test passed
[ 0.240192] prandom: 100 self tests passed
[ 0.244372] pinctrl core: initialized pinctrl subsystem
[ 0.252733] NET: Registered protocol family 16
[ 0.257815] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.269329] gpio-oxnas 44000000.gpio: at address c8846000
[ 0.275138] gpio-oxnas 44100000.gpio: at address c8848000
[ 0.281228] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
|
Re: Need a rootfs with Kernel 3.17 January 08, 2018 11:42AM |
Admin Registered: 13 years ago Posts: 18,550 |
dippes,
Let's take out the mtdparts.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Let's take out the mtdparts.
setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr' setenv dt_usb_boot 'run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm' boot
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Need a rootfs with Kernel 3.17 January 08, 2018 12:42PM |
Registered: 6 years ago Posts: 17 |
|
Re: Need a rootfs with Kernel 3.17 January 08, 2018 11:30PM |
Admin Registered: 13 years ago Posts: 18,550 |
dippes,
1. Use another USB thumb drive and create a new rootfs using Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2.
2. Boot with this new rootfs.
Power up, interrupt serial console and
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
1. Use another USB thumb drive and create a new rootfs using Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2.
Quote
Updated 02 Aug 2017:
Rootfs Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2 was uploaded.
Basic Debian stretch Oxnas rootfs for Popo Pro/Classic V3 plug:
- tarball size: 180M
- install size: 477M
- Installed packages: nano, avahi, ntp, busybox-syslogd (log to RAM), htop, dialog, bz2, iperf, ethtool, sysvinit-core, sysvinit, sysvinit-utils, mtd-utils.
- see LED controls in /etc/rc.local, and /etc/rc0.d/K08halt
- see some useful aliases in /root/.profile
- root password: root
2. Boot with this new rootfs.
Power up, interrupt serial console and
setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data) earlyprintk=serial' setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr' setenv dt_usb_boot 'run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm' boot
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Need a rootfs with Kernel 3.17 January 09, 2018 10:58AM |
Registered: 6 years ago Posts: 17 |
|
Re: Need a rootfs with Kernel 3.17 January 09, 2018 11:54AM |
Admin Registered: 13 years ago Posts: 18,550 |
dippes,
Please post the entire log of the terminal session when you create the rootfs usingDebian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2.
I think there is something went wrong when you did that. Just copy and paste the terminal log of how you create the partition, and format with ext3, and untar the rootfs tarball. Perhaps I will be able to spot something that was incorrect.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Please post the entire log of the terminal session when you create the rootfs usingDebian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2.
I think there is something went wrong when you did that. Just copy and paste the terminal log of how you create the partition, and format with ext3, and untar the rootfs tarball. Perhaps I will be able to spot something that was incorrect.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Need a rootfs with Kernel 3.17 January 09, 2018 02:19PM |
Registered: 6 years ago Posts: 17 |
root@HP-Server / > fdisk /dev/sdc
Befehl (m für Hilfe): o
Building a new DOS disklabel with disk identifier 0x3854c2be.
Changes will remain in memory only, until you decide to write them.
After that, of course, the previous content won't be recoverable.
Warnung: Schreiben wird ungültiges Flag 0x0000 in Part.-tabelle 4 korrigieren
Befehl (m für Hilfe): n
Partition type:
p primary (0 primary, 0 extended, 4 free)
e extended
Select (default p): p
Partitionsnummer (1-4, Vorgabe: 1): 1
Erster Sektor (2048-15633407, Vorgabe: 2048):
Benutze den Standardwert 2048
Last Sektor, +Sektoren or +size{K,M,G} (2048-15633407, Vorgabe: 15633407):
Benutze den Standardwert 15633407
Befehl (m für Hilfe): w
Die Partitionstabelle wurde verändert!
Rufe ioctl() um Partitionstabelle neu einzulesen.
Synchronisiere Platten.
root@HP-Server / > mkfs.ext3 /dev/sdc1
mke2fs 1.42.9 (4-Feb-2014)
Dateisystem-Label=
OS-Typ: Linux
Blockgröße=4096 (log=2)
Fragmentgröße=4096 (log=2)
Stride=0 Blöcke, Stripebreite=0 Blöcke
488640 Inodes, 1953920 Blöcke
97696 Blöcke (5.00%) reserviert für den Superuser
Erster Datenblock=0
Maximale Dateisystem-Blöcke=2004877312
60 Blockgruppen
32768 Blöcke pro Gruppe, 32768 Fragmente pro Gruppe
8144 Inodes pro Gruppe
Superblock-Sicherungskopien gespeichert in den Blöcken:
32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632
Platz für Gruppentabellen wird angefordert: erledigt
Inode-Tabellen werden geschrieben: erledigt
Erstelle Journal (32768 Blöcke): erledigt
Schreibe Superblöcke und Dateisystem-Accountinginformationen: erledigt
root@HP-Server / > e2label /dev/sdc1 rootfs
root@HP-Server /media/stick > ls Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2 lost+found
/media/stick > tar xvjf Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2
|
Re: Need a rootfs with Kernel 3.17 January 10, 2018 01:06PM |
Admin Registered: 13 years ago Posts: 18,550 |
dippes,
Are you root at this point?
It you were root, then all the steps look good. If you were not, then redo the above step.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Are you root at this point?
/media/stick > tar xvjf Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2
It you were root, then all the steps look good. If you were not, then redo the above step.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Need a rootfs with Kernel 3.17 January 10, 2018 01:12PM |
Registered: 6 years ago Posts: 17 |
this is the mountpoint from the usb stick in my Linuxmachine
Edited 2 time(s). Last edit at 01/10/2018 01:23PM by dippes.
root@HP-Server ~ > mount -t ext3 /dev/sdc1 /media/stick root@HP-Server /media/stick > ls -l insgesamt 184052 drwxr-xr-x 2 root root 4096 Aug 1 10:36 bin drwxr-xr-x 3 root root 4096 Aug 2 10:29 boot -rw-r----- 1 root root 188188318 Jan 10 17:14 Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2 drwxr-xr-x 5 root root 4096 Feb 24 2012 dev drwxr-xr-x 61 root root 4096 Jan 1 1970 etc drwxr-xr-x 2 root root 4096 Jan 22 2012 home drwxr-xr-x 13 root root 4096 Aug 1 07:38 lib drwx------ 2 root root 16384 Feb 24 2012 lost+found drwxr-xr-x 2 root root 4096 Feb 24 2012 media drwxr-xr-x 2 root root 4096 Aug 1 07:23 mnt drwxr-xr-x 2 root root 4096 Feb 24 2012 opt drwxr-xr-x 2 root root 4096 Jan 22 2012 proc drwx------ 5 root root 4096 Aug 2 02:19 root drwxr-xr-x 2 root root 4096 Feb 8 2013 run drwxr-xr-x 2 root root 4096 Aug 1 10:21 sbin drwxr-xr-x 2 root root 4096 Feb 24 2012 srv drwxr-xr-x 2 root root 4096 Jan 1 2011 sys drwxrwxrwt 2 root root 4096 Jan 1 1970 tmp drwxr-xr-x 10 root root 4096 Feb 24 2012 usr drwxr-xr-x 11 root root 4096 Jan 1 1970 var
yesQuote
bodhi
Are you root at this point?
Edited 2 time(s). Last edit at 01/10/2018 01:23PM by dippes.
|
Re: Need a rootfs with Kernel 3.17 January 10, 2018 11:31PM |
Admin Registered: 13 years ago Posts: 18,550 |
dippes,
This is a strange problem. The behavior as though the DTB was corrupted.
We could try to flash the latest u-boot for this box (uboot.2015.10-tld-2) in serial console to see if it helps. But even with new u-boot, it might not boot pass that point.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
This is a strange problem. The behavior as though the DTB was corrupted.
We could try to flash the latest u-boot for this box (uboot.2015.10-tld-2) in serial console to see if it helps. But even with new u-boot, it might not boot pass that point.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Need a rootfs with Kernel 3.17 January 11, 2018 09:00AM |
Admin Registered: 13 years ago Posts: 18,550 |
What type of USB drive are you using? USB 2.0, 3.0, model, brand ...
You could try to recreate the rootfs using a different USB stick. Prefereably USB 2.0, Sandisk brand.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 01/11/2018 09:06AM by bodhi.
lsusb -vvv
You could try to recreate the rootfs using a different USB stick. Prefereably USB 2.0, Sandisk brand.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 01/11/2018 09:06AM by bodhi.
|
Re: Need a rootfs with Kernel 3.17 January 11, 2018 10:58AM |
Registered: 6 years ago Posts: 17 |
Hello bodhi
i use SanDisk Cruzer 8 GB stick and try 3 different USB drives.
Bevor my Pogo crashed all my USB Sticks working fine.
i use SanDisk Cruzer 8 GB stick and try 3 different USB drives.
Bevor my Pogo crashed all my USB Sticks working fine.
us 001 Device 105: ID 0781:5567 SanDisk Corp. Cruzer Blade
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0781 SanDisk Corp.
idProduct 0x5567 Cruzer Blade
bcdDevice 1.26
iManufacturer 1 SanDisk
iProduct 2 Cruzer Blade
iSerial 3 4C532000030318123381
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 200mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
|
Re: Need a rootfs with Kernel 3.17 January 12, 2018 12:00AM |
Admin Registered: 13 years ago Posts: 18,550 |
dippes,
Boot with the rootfs Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2 on USB.
And post the entire serial console log here (from u-boot banner until it stucks or reset). I'd like to see what happens after this line
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Boot with the rootfs Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2 on USB.
And post the entire serial console log here (from u-boot banner until it stucks or reset). I'd like to see what happens after this line
[ 0.281228] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Need a rootfs with Kernel 3.17 January 12, 2018 06:19AM |
Registered: 6 years ago Posts: 17 |
with
without
setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data) earlyprintk=serial' setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr' setenv dt_usb_boot 'run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm'
U-Boot SPL 2013.10 (Apr 27 2014 - 19:08:27)
Boot device: NAND
Attempting to set PLLA to 800 MHz ...
plla_ctrl0 : 0000030a
plla_ctrl1 : 00400000
plla_ctrl2 : 007f0068
plla_ctrl3 : 00000193
PLLA Set
U-Boot 2013.10-tld-3 (May 15 2014 - 14:54:14) for OXNAS
DRAM: 128 MiB
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0
OX820 # setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data) earlyprintk=serial'
OX820 # setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr'
OX820 # setenv dt_usb_boot 'run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm'
OX820 # boot
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
4621824 bytes read in 388 ms (11.4 MiB/s)
4594376 bytes read in 359 ms (12.2 MiB/s)
7067 bytes read in 205 ms (33.2 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-4.4.54-oxnas-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4621760 Bytes = 4.4 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 60e00000 ...
Image Name: initramfs-4.4.54-oxnas-tld-1
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 4594312 Bytes = 4.4 MiB
Load Address: 60000000
Entry Point: 60000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
Booting using the fdt blob at 0x62c00000
Loading Kernel Image ... OK
Loading Ramdisk to 679c8000, end 67e29a88 ... OK
Loading Device Tree to 679c3000, end 679c7b9a ... OK
Led: GREEN
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.4.54-oxnas-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #2 SMP PREEMPT Sat Mar 18 23:09:58 PDT 2017
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Pogoplug V3 Pro
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[ 0.000000] PERCPU: Embedded 12 pages/cpu @c7eda000 s17696 r8192 d23264 u49152
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data) earlyprintk=serial
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 116204K/131072K available (6410K kernel code, 288K rwdata, 1908K rodata, 224K init, 247K bss, 14868K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0827e14 (8320 kB)
[ 0.000000] .init : 0xc0828000 - 0xc0860000 ( 224 kB)
[ 0.000000] .data : 0xc0860000 - 0xc08a8378 ( 289 kB)
[ 0.000000] .bss : 0xc08a8378 - 0xc08e6350 ( 248 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:160
[ 0.000000] clocksource: rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[ 0.000007] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[ 0.008337] Console: colour dummy device 80x30
[ 0.012897] Calibrating delay loop... 319.48 BogoMIPS (lpj=1597440)
[ 0.062594] pid_max: default: 32768 minimum: 301
[ 0.067435] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.074140] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.082106] Initializing cgroup subsys net_cls
[ 0.086686] CPU: Testing write buffer coherency: ok
[ 0.092108] Setting up static identity map for 0x60008220 - 0x60008258
[ 0.229952] Brought up 2 CPUs
[ 0.233000] SMP: Total of 2 processors activated (638.97 BogoMIPS).
[ 0.240199] devtmpfs: initialized
[ 0.249364] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.259317] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 0.265838] prandom: seed boundary self test passed
[ 0.275432] prandom: 100 self tests passed
[ 0.279605] pinctrl core: initialized pinctrl subsystem
[ 0.285788] NET: Registered protocol family 16
[ 0.290951] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.319818] cpuidle: using governor ladder
[ 0.349816] cpuidle: using governor menu
[ 0.359255] gpio-oxnas 44000000.gpio: at address c8848000
[ 0.365186] gpio-oxnas 44100000.gpio: at address c884a000
[ 0.371297] pinctrl-oxnas pinctrl: initialized OX820 pinctrl driver
without
U-Boot SPL 2013.10 (Apr 27 2014 - 19:08:27)
Boot device: NAND
Attempting to set PLLA to 800 MHz ...
plla_ctrl0 : 0000030a
plla_ctrl1 : 00400000
plla_ctrl2 : 007f0068
plla_ctrl3 : 00000193
PLLA Set
U-Boot 2013.10-tld-3 (May 15 2014 - 14:54:14) for OXNAS
DRAM: 128 MiB
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net:
Led: GREEN
mii0
Main Loop
Hit any key to stop autoboot: 0
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
4621824 bytes read in 388 ms (11.4 MiB/s)
4594376 bytes read in 359 ms (12.2 MiB/s)
## Booting kernel from Legacy Image at 60500000 ...
Image Name: Linux-4.4.54-oxnas-tld-1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4621760 Bytes = 4.4 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 60e00000 ...
Image Name: initramfs-4.4.54-oxnas-tld-1
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 4594312 Bytes = 4.4 MiB
Load Address: 60000000
Entry Point: 60000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Led: GREEN
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Error: unrecognized/unsupported machine ID (r1 = 0x00000480).
Available machine support:
ID (hex) NAME
ffffffff PLXTECH NAS782X SoC (Flattened Device Tree)
Please check your kernel config and/or bootloader.
|
Re: Need a rootfs with Kernel 3.17 January 12, 2018 09:46AM |
Admin Registered: 13 years ago Posts: 18,550 |
dippes,
I think I've totally missed the fact that you have the POGO-P24, I thought you have the Pogo Pro :) (too many things that has been distracted my thinking). This box no Wifi card! So please try this new envs set with the rootfs Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2 .
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
I think I've totally missed the fact that you have the POGO-P24, I thought you have the Pogo Pro :) (too many things that has been distracted my thinking). This box no Wifi card! So please try this new envs set with the rootfs Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2 .
setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data) earlyprintk=serial' setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr' setenv dt_usb_boot 'run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm' setenv dt_load_dtb 'ext2load usb 0:1 $dtb_addr /boot/dts/ox820-pogoplug-classic.dtb'
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Need a rootfs with Kernel 3.17 January 13, 2018 03:42AM |
Registered: 6 years ago Posts: 17 |
Its really a Pogoplug-Pro.With the 4 lines the device running.But afte the reboot i need to refresh the lines.
How can you saved it permanently?
How can you saved it permanently?
setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=41000000.nand:14m(boot),-(data) earlyprintk=serial' setenv dt_bootm 'bootm $uimage_addr $uinitrd_addr $dtb_addr' setenv dt_usb_boot 'run dt_load_uimage; run dt_load_initrd; run dt_load_dtb; run dt_bootm' setenv dt_load_dtb 'ext2load usb 0:1 $dtb_addr /boot/dts/ox820-pogoplug-classic.dtb'
|
Re: Need a rootfs with Kernel 3.17 January 13, 2018 03:59AM |
Admin Registered: 13 years ago Posts: 18,550 |
dippes,
> Its really a Pogoplug-Pro.With the 4 lines the
> device running.
It is not a Pogoplug Pro V3. it is a Pogoplug Classic V3. The difference is Wifi PCIe card (Pro version has it, Classic version does not).
Please post the entire serial console booting log.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> Its really a Pogoplug-Pro.With the 4 lines the
> device running.
It is not a Pogoplug Pro V3. it is a Pogoplug Classic V3. The difference is Wifi PCIe card (Pro version has it, Classic version does not).
Please post the entire serial console booting log.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Need a rootfs with Kernel 3.17 January 13, 2018 12:19PM |
Registered: 6 years ago Posts: 17 |
|
Re: Need a rootfs with Kernel 3.17 January 13, 2018 12:32PM |
Admin Registered: 13 years ago Posts: 18,550 |
dippes,
Cool! glad it is working well for you finally.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Cool! glad it is working well for you finally.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
