Pogoplug E02 does not boot

Hi
after some tiome I decided to resurrect my Pogoplug E02 but I don't manage to boot it. i had a rescue system on it, so I used a serial console to update the uboot, which has been successful:

U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700)
Pogo E02

SoC:   Kirkwood 88F6281_A0
DRAM:  256 MiB
WARNING: Caches not enabled
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0

The flash drive is formated as required:

root@mm-server:~/boodhi# fdisk -l /dev/sde

Disk /dev/sde: 15.4 GB, 15376000000 bytes
45 heads, 18 sectors/track, 37075 cylinders, total 30031250 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000

   Device Boot      Start         End      Blocks   Id  System
/dev/sde1   *        2048    30031249    15014601   83  Linux
root@mm-server:~/boodhi# e2label /dev/sde1
rootfs
root@mm-server:~/boodhi# blkid
...
/dev/sde1: LABEL="rootfs" UUID="6360643f-714a-4a17-b253-d8e3c89140b9" SEC_TYPE="ext2" TYPE="ext3"
...
root@mm-server:~/boodhi#

and the newest debian is extracted on the drive as in the description, and the step 4 ("Create uImage with embedded DTB") I skipped as I am using the bewest U-Boot.

But I get the following output:

Hit any key to stop autoboot:  0
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
       scanning usb for storage devices...
Use USB retry period from the environment: 15 second(s)
1 Storage Device(s) found
Unknown command 'ide' - try 'help'
Unknown command 'mmc' - try 'help'

Partition Map for USB device 0  --   Partition Type: DOS

Part    Start Sector    Num Sectors     UUID            Type
  1     2048            30029202        00000000-01     83 Boot

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **
Unknown command 'ide' - try 'help'
Unknown command 'mmc' - try 'help'
running scan_disk ...
Scan device usb
device usb 0:1
1 bytes read in 692 ms (0 Bytes/s)
Found bootable drive on usb 0
loading uImage ...
3821592 bytes read in 907 ms (4 MiB/s)
loading uInitrd ...
7245696 bytes read in 914 ms (7.6 MiB/s)
loading DTB /boot/kirkwood-pogo_e02.dtb ...
** File not found /boot/kirkwood-pogo_e02.dtb **
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-4.12.1-kirkwood-tld-1
   Created:      2017-07-20   8:11:24 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3821528 Bytes = 3.6 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
   Image Name:   initramfs-4.12.1-kirkwood-tld-1
   Created:      2017-07-24   0:18:23 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    7245632 Bytes = 6.9 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
   Loading Ramdisk to 0f426000, end 0fb0ef40 ... OK
Using machid 0xdd6 from environment

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

Error: unrecognized/unsupported machine ID (r1 = 0x00000dd6).

Available machine support:

ID (hex)        NAME
ffffffff        Generic DT based system
ffffffff        Marvell Kirkwood (Flattened Device Tree)

Please check your kernel config and/or bootloader.

If I unplug the flash drive, I get the following:

U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700)
Pogo E02

SoC:   Kirkwood 88F6281_A0
DRAM:  256 MiB
WARNING: Caches not enabled
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot:  0
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Unknown command 'ide' - try 'help'
Unknown command 'mmc' - try 'help'
## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0
loading envs from usb 0 ...
** Bad device usb 0 **
Unknown command 'ide' - try 'help'
Unknown command 'mmc' - try 'help'
running scan_disk ...
Scan device usb
device usb 0:1
** Bad device usb 0 **
device usb 1:1
** Bad device usb 1 **
device usb 2:1
** Bad device usb 2 **
device usb 3:1
** Bad device usb 3 **
Scan device ide
Unknown command 'ide' - try 'help'
device ide 0:1
** Bad device ide 0 **
device ide 1:1
** Bad device ide 1 **
device ide 2:1
** Bad device ide 2 **
device ide 3:1
** Bad device ide 3 **
Scan device mmc
Unknown command 'mmc' - try 'help'
device mmc 0:1
** Bad device mmc 0 **
device mmc 1:1
** Bad device mmc 1 **
device mmc 2:1
** Bad device mmc 2 **
device mmc 3:1
** Bad device mmc 3 **
loading uImage ...
** Bad device usb 0 **
loading uInitrd ...
** Bad device usb 0 **
loading DTB /boot/kirkwood-pogo_e02.dtb ...
** Bad device usb 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
PogoE02>

Any suggestions on how I can proceed?

Rainer

===========================
Blog: https://rmkrug.wordpress.com/

1 x Pogoplug E02 (pink): Logitech media server

1 x Pogoplug E02 (pink): FTP server only (throw away configuration - quick to rebuild)

1 x GoFlex Net: running OpenMediaVault

Stupid me - I used /boot/kirkwood-pogo_e02.dtb instead of /boot/dts/kirkwood-pogo_e02.dtb

I copied the file to /boot and it is booting now.

Changed it to

fw_setenv dtb_file '/boot/dts/kirkwood-pogo_e02.dtb'

Now to install the rescue system.

Thanks,

Rainer

===========================
Blog: https://rmkrug.wordpress.com/

1 x Pogoplug E02 (pink): Logitech media server

1 x Pogoplug E02 (pink): FTP server only (throw away configuration - quick to rebuild)

1 x GoFlex Net: running OpenMediaVault