Debian Installation on Thecus N2350 (Marvell Armada 385)

Manuel,

> How did you get that information?

I have an alias that include all the following commands that I can run to get a summary of system info at a glance.

dmesg | grep -i machine | cut -c40-120
Thecus N2350

uname -a
Linux version 5.2.9-mvebu-tld-1 (root@tldDebianVM) (gcc version 7.4.0 (Ubuntu/Linaro 7.4.0-1ubuntu1~18.04.1)) #1 SMP PREEMPT Mon Aug 19 12:47:39 PDT 2019

cat /etc/debian_version
Debian 10.0

cat /proc/cmdline
console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=pxa3xx_nand-0:-(ubifs);spi1.0:0x00400000(uboot),0x00010000@0x00100000(uboot_env),0x00010000@0x00300000(uboot_scr) earlyprintk=serial

fw_printenv uboot_version  # I usually set u-uboot_version env so I can tell from Debian which version I've installed)
uboot_version=U-Boot 2013.01 (Nov 12 2018 - 20:56:19) Marvell version: 2015_T1.0p18-tld-4

> I think it might be possible that i had the
> problem with random MAC addresses also before the
> upgrade, but i did not keep the customized hard
> coded MAC address in the config file, but chose
> the new one from the package maintainer - not sure
> about that.

I always have persistent MAC address on this Thecus N2350 box since we added the alias eth0 to the DTS!

So it is still a mystery why we have the same box, same kernel but the MAC address behavior is different :)

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

bodhi Wrote:
-------------------------------------------------------
> Manuel,
>

> dmesg | grep -i machine | cut -c40-120
> Thecus N2350
> 
> uname -a
> Linux version 5.2.9-mvebu-tld-1 (root@tldDebianVM)
> (gcc version 7.4.0 (Ubuntu/Linaro
> 7.4.0-1ubuntu1~18.04.1)) #1 SMP PREEMPT Mon Aug 19
> 12:47:39 PDT 2019
> 
> cat /etc/debian_version
> Debian 10.0
> 
> cat /proc/cmdline
> console=ttyS0,115200 root=LABEL=rootfs
> rootdelay=10
> mtdparts=pxa3xx_nand-0:-(ubifs);spi1.0:0x00400000(uboot),0x00010000@0x00100000(uboot_env),0x00010000@0x00300000(uboot_scr)
> earlyprintk=serial
> 
> fw_printenv uboot_version  # I usually set
> u-uboot_version env so I can tell from Debian
> which version I've installed)
> uboot_version=U-Boot 2013.01 (Nov 12 2018 -
> 20:56:19) Marvell version: 2015_T1.0p18-tld-4
>

Thecus N2350
Linux vega 5.2.9-mvebu-tld-1 #1 SMP PREEMPT Mon Aug 19 12:47:39 PDT 2019 armv7l GNU/Linux
10.0
console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=pxa3xx_nand-0:-(ubifs);spi1.0:0x00400000(uboot),0x00010000@0x00100000(uboot_env),0x00010000@0x00300000(uboot_scr) earlyprintk=serial

> So it is still a mystery why we have the same box,
> same kernel but the MAC address behavior is
> different :)
Yap, weird. I have also no idea at the moment.

Hi Manuel,

I've finally have time to write this :)

https://forum.doozan.com/read.php?2,92234

Please take a look and try it if you would like to.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)



Edited 1 time(s). Last edit at 10/26/2019 06:41AM by bodhi.

Great! I briefly looked over it, i hope some people will use it.
I have no time to test it. Also my box is in "production" use now for quite some time. Running great!

A heads up. I will release u-boot 2023.01 for this box pretty soon.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Hello all,
first sorry for using this thread for this but i messed up N2350 and i need rescue firmware to try restore it.
/os7-n2350n4350-v302021-rescue-usb-upgrade
If someone have zip or working link i would be grateful?
Thanks.

vaha,

> Hello all,
> first sorry for using this thread for this but i
> messed up N2350 and i need rescue firmware to try
> restore it.
> /os7-n2350n4350-v302021-rescue-usb-upgrade
> If someone have zip or working link i would be
> grateful?
> Thanks.

I've never used this rescue USB so don't have it. Let's see if any body has come across this before.

If nobody responds here after a couple days, you can try sending email to Thecus support. In the past, they were quite helpful and responded to my request for GPL source very quickly. And probably you will need to give them your box serial number.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Thank you for response,

i did asked support and i got this response from them:

Quote
Dear Sir,

Thank you for your reply.

Thecus NAS with 2 years warranty, and also at least have 5 years design hardware life, but this N2350V1.0184930002 been over 5+ years, it is out of service already.

If able to access for data storage here strongly recommend backup data for new storage ASAP and retire this system,

If unable to access N2350 anymore, please try to boot N2350 up without HDD and check from Thecus Setup Wizard again, once it is without help, please the place where you purchase from for RMA service.

Here is file in wayback machine https://web.archive.org/web/20200815144739/https://www.thecus.com/Downloads/DOM/

N2350_3.02.02_rescue_fw.zip

but i can't download it.

You are my last hope....

vaha,

Thecus has a download center.

https://www.thecus.com/Download-Center

The N2350 is still on the list. But I can't find rescue fw on that page.

=====

If you cannot find this rescue_fw.img, you can install Debian on USB drive, and then copy your data from the HDDs to make backup of them.

The first thing you need to do is connect serial console, boot it up and we can see where the problem is. If you're lucky, the problem is easy to fix, that I can help, then you don't need rescue fw, or run Debian.

However, since this box is already EOL, you need to consider running Debian on it and forget about stock FW.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Changed the thread, I hope it's more suitable for debug and installation questions.


bodhi Wrote:
-------------------------------------------------------
> 1. Square: Vcc 3.3V
> 2. TXD
> 3. RXD
> 4. GND
>
> Connect only TXD, RXD, and GND. Do
> not connect 3.3V.
>
> You could connect the wires temporarily to the 3
> holes. No need to solder unless you want a
> permanent serial console.

Thank you for the detailed explanation.
Could you please check, is everything correct? I added an image to that post.


Thanks,
Nikola204



Edited 1 time(s). Last edit at 12/14/2025 03:13AM by Nikola204.

J1 serial port (right to left, outside looking in).

1. Square: Vcc 3.3V
2. TXD
3. RXD
4. GND

Means after you open the case cover, you'll see the board is mounted perpendicular. Look at the right side of the board (outside looking in), J1 is at the lower left corner. The unpopulated header is 4 holes, horizontally ( in some other boards, the header is installed with 4 pins).

The right most hole has square marking (the other 3 do not). Start counting, right to left,

pin 1 = Square hole, which is 3.3V

So there is only one way of reading it. In order to count right to left, you must already have the correct orientation.

Your picture is wrong.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)



Edited 2 time(s). Last edit at 12/14/2025 03:10PM by bodhi.

Now I see on the photo (and disassembled my box) and understand what does it mean "square" and "4". Waiting for my USB to UART connector (for delivery) and will try to find out why it's not booting up via USB.
Many thanks for your help!

Hi bodhi
Fortunately I received my USB UART and connected it to NAS. Here is my output with the USB drive connected.

BootROM - 1.73
Booting from SPI flash


General initialization - Version: 1.0.0
AVS selection from EFUSE disabled (Skip reading EFUSE values)
Overriding default AVS value to: 0x23
Detected Device ID 6820
High speed PHY - Version: 2.0

Init Customer board board SerDes lanes topology details:
 | Lane # | Speed|    Type     |
 ------------------------------|
 |   0    |  0   |  SGMII0     |
 |   1    |  3   |  SATA0      |
 |   2    |  3   |  SATA1      |
 |   4    |  5   |  USB3 HOST0 |
 |   5    |  5   |  USB3 HOST1 |
 -------------------------------
High speed PHY - Ended Successfully
DDR4 Training Sequence - Ver TIP-0.23.(Sublib 0.8)0
DDR4 Training Sequence - Switching XBAR Window to FastPath Window 
DDR4 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED

 __   __                      _ _
|  \/  | __ _ _ ____   _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| |  | | (_| | |   \ V /  __/ | |
|_|  |_|\__,_|_|    \_/ \___|_|_|
         _   _     ____              _
        | | | |   | __ )  ___   ___ | |_ 
        | | | |___|  _ \ / _ \ / _ \| __| 
        | |_| |___| |_) | (_) | (_) | |_ 
         \___/    |____/ \___/ \___/ \__| 
 ** LOADER **


U-Boot 2013.01 (Nov 12 2018 - 20:56:19) Marvell version: 2015_T1.0p18-tld-4

Board: A38x-Customer0-Thecus-N2350
SoC:   MV88F6820 Rev A0
       running 2 CPUs
CPU:   ARM Cortex A9 MPCore (Rev 1) LE
       CPU 0
       CPU    @ 1066 [MHz]
       L2     @ 800 [MHz]
       TClock @ 200 [MHz]
       DDR4    @ 800 [MHz]
       DDR4 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM:  1 GiB
NAND:  512 MiB
MMC:   mv_sdh: 0
SF: Detected MX25L3205D with page size 64 KiB, total 4 MiB
USB2.0 0: Host Mode
USB3.0 0: Host Mode
USB3.0 1: Host Mode

Map:   Code:                    0x3fed4000:0x3ff9659c
       BSS:                     0x3ffeff24
       Stack:                   0x3f9c3f20
       Heap:                    0x3f9c4000:0x3fed4000
       U-Boot Environment:      0x00100000:0x00110000 (SPI)

Board configuration detected:
Net:   
|  port  | Interface | PHY address  |
|--------|-----------|--------------|
| egiga0 |   SGMII   |     0x01     |
egiga0 [PRIME]
Hit any key to stop autoboot:  0 
Booting Debian ...
running scan_disk ...
Scan device usb
(Re)start USB...
USB0:   Port (usbActive) : 0    Interface (usbType = 3) : Anson:xhci_usb_lowlevel_init--1--index=0
Anson:xhci_usb_lowlevel_init--2
Anson:Register 2000120 NbrPorts 2
USB XHCI 1.00
Anson:xhci_usb_lowlevel_init--3
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... Device NOT ready
   Request Sense returned 02 3A 00
1 Storage Device(s) found
       scanning usb for ethernet devices... 0 Ethernet Device(s) found
device usb 0:1
** Bad device size - usb 0 **
device usb 1:1
** Bad device usb 1 **
device usb 2:1
** Bad device usb 2 **
device usb 3:1
** Bad device usb 3 **
device usb 4:1
** Bad device usb 4 **
device usb 5:1
** Bad device usb 5 **
device usb 6:1
** Bad device usb 6 **
device usb 7:1
** Bad device usb 7 **
Scan device scsi

Reset SCSI
AHCI init for unit0
SATA link 0 timeout.
SATA link 1 timeout.

Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found
scanning bus for devices...
Found 0 device(s).
device scsi 0:1
** Bad device scsi 0 **
device scsi 1:1
** Bad device scsi 1 **
device scsi 2:1
** Bad device scsi 2 **
device scsi 3:1
** Bad device scsi 3 **
device scsi 4:1
** Bad device scsi 4 **
device scsi 5:1
** Bad device scsi 5 **
device scsi 6:1
** Bad device scsi 6 **
device scsi 7:1
** Bad device scsi 7 **
Booting from usb 0:1 …
loading uImage ...
** Bad device size - usb 0 **
Booting stock ...
(Re)start USB...
USB0:   Port (usbActive) : 0    Interface (usbType = 3) : Anson:xhci_usb_lowlevel_init--1--index=0
Anson:xhci_usb_lowlevel_init--2
Anson:Register 2000120 NbrPorts 2
USB XHCI 1.00
Anson:xhci_usb_lowlevel_init--3
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... Device NOT ready
   Request Sense returned 02 3A 00
1 Storage Device(s) found
       scanning usb for ethernet devices... 0 Ethernet Device(s) found
** Bad device size - usb 0 **
incorrect device type in spi0=spi_flash
invalid mtd device 'spi_flash'
Creating 1 MTD partitions on "nand0":
0x000000000000-0x000020000000 : "mtd=0"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    126976 bytes
UBI: smallest flash I/O unit:    2048
UBI: VID header offset:          2048 (aligned 2048)
UBI: data offset:                4096
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=0"
UBI: MTD device size:            512 MiB
UBI: number of good PEBs:        4087
UBI: number of bad PEBs:         9
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     4
UBI: available PEBs:             7
UBI: total number of reserved PEBs: 4080
UBI: number of PEBs reserved for bad PEB handling: 40
UBI: max/mean erase counter: 3/1
UBIFS: mounted UBI device 0, volume 1, name "boot"
UBIFS: mounted read-only
UBIFS: file system size:   91422720 bytes (89280 KiB, 87 MiB, 720 LEBs)
UBIFS: journal size:       9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format:       w4/r0 (latest is w4/r0)
UBIFS: default compressor: LZO
UBIFS: reserved for root:  0 bytes (0 KiB)
Loading file 'boot/bzImage' to addr 0x02000000 with size 5070467 (0x004d5e83)...
Done
Loading file 'boot/ramdisk' to addr 0x03000000 with size 16013180 (0x00f4577c)...
Done
## Booting kernel from Legacy Image at 02000000 ...
   Image Name:   linux-3.10.thecus.develop-2015_T
   Created:      2019-05-17   5:18:15 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    5070403 Bytes = 4.8 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 03000000 ...
   Image Name:   
   Created:      2019-05-17   5:30:23 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    16013116 Bytes = 15.3 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.10.105.15 (root@localhost.localdomain) (gcc version 4.8.5 (Marvell GCC release 20160307-7f3c83a0) ) #1 SMP Fri May 17 13:17:52 CST 2019
[    0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: Marvell Armada 380/381/382/383/384/385/388 (Device Tree), model: Marvell Armada 385 Development Board
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] PERCPU: Embedded 8 pages/cpu @c16ab000 s8704 r8192 d15872 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260594
[    0.000000] Kernel command line: root=/dev/ram0 rw max_loop=210 console=ttyS0,115200 init=/sbin/init rootdelay=3 ubi.mtd=0 mtdparts=armada-nand:-(ubifs);spi_flash:0x00400000(uboot),0x00010000@0x0010)
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] allocated 2097152 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 1024MB = 1024MB total
[    0.000000] Memory: 1011272k/1011272k available, 37304k reserved, 254976K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0800000 - 0xfff00000   ( 247 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xf0700000   ( 775 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc09162e4   (9273 kB)
[    0.000000]       .init : 0xc0917000 - 0xc095b200   ( 273 kB)
[    0.000000]       .data : 0xc095c000 - 0xc09c82e0   ( 433 kB)
[    0.000000]        .bss : 0xc09c82e0 - 0xc0a3b714   ( 462 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] 
[    0.000000]   LSP version: linux-3.10.70-2015_T1.1p9
[    0.000000] 
[    0.000000] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms
[    0.000000] L310 cache controller enabled
[    0.000000] l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B
[    0.000000] Console: colour dummy device 80x30
[    0.000589] Calibrating delay loop... 2131.55 BogoMIPS (lpj=10657792)
[    0.060021] pid_max: default: 32768 minimum: 301
[    0.060138] Mount-cache hash table entries: 512
[    0.060596] Initializing cgroup subsys memory
[    0.060617] Initializing cgroup subsys devices
[    0.060623] Initializing cgroup subsys freezer
[    0.060628] Initializing cgroup subsys blkio
[    0.060632] Initializing cgroup subsys perf_event
[    0.060661] CPU: Testing write buffer coherency: ok
[    0.060807] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.060853] Setting up static identity map for 0xc06d94f0 - 0xc06d9548
[    0.061062] mvebu-pmsu: Initializing Power Management Service Unit
[    0.061118] Initializing CPU Reset module
[    0.061845] CPU1: Booted secondary processor
[    0.120815] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.120891] Brought up 2 CPUs
[    0.120904] SMP: Total of 2 processors activated (4256.56 BogoMIPS).
[    0.120909] CPU: All CPU(s) started in SVC mode.
[    0.121302] devtmpfs: initialized
[    0.124324] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
[    0.124553] xor: measuring software checksum speed
[    0.220723]    arm4regs  :  1700.000 MB/sec
[    0.320661]    8regs     :  1257.600 MB/sec
[    0.420599]    32regs    :  1253.600 MB/sec
[    0.420605] xor: using function: arm4regs (1700.000 MB/sec)
[    0.420611] pinctrl core: initialized pinctrl subsystem
[    0.420999] regulator-dummy: no parameters
[    0.421206] NET: Registered protocol family 16
[    0.422065] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.425254] irq: Cannot allocate irq_descs @ IRQ194, assuming pre-allocated
[    0.425788] irq: Cannot allocate irq_descs @ IRQ226, assuming pre-allocated
[    0.429896] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.429904] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.448312] bio: create slab <bio-0> at 0
[    0.610618] raid6: int32x1    123 MB/s
[    0.780538] raid6: int32x2    200 MB/s
[    0.950296] raid6: int32x4    169 MB/s
[    1.120278] raid6: int32x8    193 MB/s
[    1.120284] raid6: using algorithm int32x2 (200 MB/s)
[    1.120288] raid6: using intx1 recovery algorithm
[    1.120615] mvebu-pcie pcie-controller.3: PCIe0.0: link down
[    1.120644] mvebu-pcie pcie-controller.3: PCIe1.0: link down
[    1.120817] mvebu-pcie pcie-controller.3: PCI host bridge to bus 0000:00
[    1.120828] pci_bus 0000:00: root bus resource [io  0x1000-0xfffff]
[    1.120836] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[    1.120844] pci_bus 0000:00: root bus resource [bus 00-ff]
[    1.121208] PCI: bus0: Fast back to back transfers disabled
[    1.121218] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.121227] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.121356] PCI: bus1: Fast back to back transfers enabled
[    1.121505] PCI: bus2: Fast back to back transfers enabled
[    1.121545] pci 0000:00:01.0: PCI bridge to [bus 01]
[    1.121555] pci 0000:00:02.0: PCI bridge to [bus 02]
[    1.121566] PCI: enabling device 0000:00:01.0 (0140 -> 0143)
[    1.121574] PCI: enabling device 0000:00:02.0 (0140 -> 0143)
[    1.122062] vgaarb: loaded
[    1.122418] SCSI subsystem initialized
[    1.123062] usbcore: registered new interface driver usbfs
[    1.123148] usbcore: registered new interface driver hub
[    1.123273] usbcore: registered new device driver usb
[    1.123679] Linux video capture interface: v2.00
[    1.123929] pps_core: LinuxPPS API ver. 1 registered
[    1.123936] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.123998] PTP clock support registered
[    1.124825] Bluetooth: Core ver 2.16
[    1.124911] NET: Registered protocol family 31
[    1.124916] Bluetooth: HCI device and connection manager initialized
[    1.124926] Bluetooth: HCI socket layer initialized
[    1.124934] Bluetooth: L2CAP socket layer initialized
[    1.124948] Bluetooth: SCO socket layer initialized
[    1.125402] Switching to clocksource armada_370_xp_clocksource
[    1.125438] cfg80211: Calling CRDA to update world regulatory domain
[    1.134517] NET: Registered protocol family 2
[    1.135044] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    1.135141] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    1.135239] TCP: Hash tables configured (established 8192 bind 8192)
[    1.135282] TCP: reno registered
[    1.135292] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    1.135316] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    1.135517] NET: Registered protocol family 1
[    1.137221] RPC: Registered named UNIX socket transport module.
[    1.137229] RPC: Registered udp transport module.
[    1.137233] RPC: Registered tcp transport module.
[    1.137237] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.137357] Trying to unpack rootfs image as initramfs...
[    2.067163] Freeing initrd memory: 15632K (c3001000 - c3f45000)
[    2.067534] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    2.071845] bounce pool size: 64 pages
[    2.088786] VFS: Disk quotas dquot_6.5.2
[    2.089214] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    2.093620] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.096730] NFS: Registering the id_resolver key type
[    2.096761] Key type id_resolver registered
[    2.096767] Key type id_legacy registered
[    2.096778] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    2.097224] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    2.098100] fuse init (API version 7.22)
[    2.099541] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
[    2.102551] msgmni has been set to 1507
[    2.104242] async_tx: api initialized (async)
[    2.104848] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[    2.105231] io scheduler noop registered
[    2.105239] io scheduler deadline registered (default)
[    2.105267] io scheduler cfq registered
[    2.106569] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
[    2.107328] mv_xor f1060800.xor: Marvell shared XOR driver
[    2.146209] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq )
[    2.176003] mv_xor f1060800.xor: freeing 1 in use descriptors!
[    2.176016] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( intr crc32c )
[    2.177327] mv_xor f1060900.xor: Marvell shared XOR driver
[    2.215982] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq )
[    2.245998] mv_xor f1060900.xor: freeing 1 in use descriptors!
[    2.246012] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( intr crc32c )
[    2.315478] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[    2.337898] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A
[    3.216559] console [ttyS0] enabled
[    3.224391] brd: module loaded
[    3.402344] loop: loaded (max 210 devices)
[    3.408949] nbd: registered device at major 43
[    3.426078] i2c /dev entries driver
[    3.431775] pca9532_init
[    3.440176] pca9532_id_init
[    3.448828] i2c i2c-0: Found pca9532_id at 0x61
[    3.453631] pca9532_id 0-0061: setting platform data
[    3.488441] thecus_io: board_num: 0h
[    3.492032] thecus_io: board_idx: 0h
[    3.495636] thecus_board = BOARD_N2350, thecus_mbtype = a385!
[    3.504274] SCSI Media Changer driver v0.25 
[    3.509982] ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[    3.518841] ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs 
[    3.529982] scsi0 : ahci_mv_platform
[    3.534382] scsi1 : ahci_mv_platform
[    3.538676] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58
[    3.546666] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58
[    3.558542] armada-nand f10d0000.nand: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC
[    3.572974] NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit), 512MiB, page size: 2048, OOB size: 64
[    3.585846] Bad block table found at page 261824, version 0x01
[    3.592788] Bad block table found at page 261760, version 0x01
[    3.598857] nand_read_bbt: bad block at 0x00000d400000
[    3.604035] nand_read_bbt: bad block at 0x00001ff80000
[    3.609231] nand_read_bbt: bad block at 0x00001ffa0000
[    3.614390] nand_read_bbt: bad block at 0x00001ffc0000
[    3.619561] nand_read_bbt: bad block at 0x00001ffe0000
[    3.624745] 1 cmdlinepart partitions found on MTD device armada-nand
[    3.631133] Creating 1 MTD partitions on "armada-nand":
[    3.636389] 0x000000000000-0x000020000000 : "ubifs"
[    3.645084] m25p80 spi1.0: mx25l3205d (4096 Kbytes)
[    3.650019] 2 ofpart partitions found on MTD device spi1.0
[    3.655537] Creating 2 MTD partitions on "spi1.0":
[    3.660351] 0x000000000000-0x000000400000 : "U-Boot-img"
[    3.667299] 0x000000100000-0x000000400000 : "U-Boot-env"
[    3.679325] libphy: Fixed MDIO Bus: probed
[    3.684305] SoC: model = 0x6820, revision = 0x4
[    3.688963] mvPncVirtBase = 0xf0c00000, pncTcamSize = 1024
[    3.694471]   o 3 Giga ports supported
[    3.698248]   o SKB recycle supported for SWF (Disabled)
[    3.703581]   o NETA acceleration mode 4
[    3.707526]   o BM supported for CPU: 4 BM pools
[    3.712161]   o PnC supported (Enabled)
[    3.716017]   o RX Queue support: 8 Queues * 256 Descriptors
[    3.721699]   o TX Queue support: 8 Queues * 532 Descriptors
[    3.727385]   o GSO supported
[    3.730363]   o GRO supported
[    3.733341]   o Receive checksum offload supported
[    3.738156]   o Transmit checksum offload supported
[    3.743052]   o Driver ERROR statistics enabled
[    3.747605]   o Driver INFO statistics enabled
[    3.752065]   o Driver DEBUG statistics enabled
[    3.756617] 
[    3.759466] port #0: is_sgmii=1, is_rgmii=0, phy_addr=1
[    3.764761]   o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800
[    3.773118] 
[    3.774615]   o Port 0 is connected to Linux netdevice
[    3.785244]     o eth0, ifindex = 3, GbE port = 0
[    3.793414]  giga p=0: mtu=1500, mac=42:05:f0:4c:6d:0f (random)
[    3.799429] 
[    3.801904] libphy: orion_mdio_bus: probed
[    3.807985] PPP generic driver version 2.4.2
[    3.812982] PPP BSD Compression module registered
[    3.817798] PPP Deflate Compression module registered
[    3.822881] PPP MPPE Compression module registered
[    3.827720] NET: Registered protocol family 24
[    3.832453] usbcore: registered new interface driver asix
[    3.838131] usbcore: registered new interface driver ax88179_178a
[    3.844463] usbcore: registered new interface driver cdc_ether
[    3.850552] usbcore: registered new interface driver net1080
[    3.856499] usbcore: registered new interface driver cdc_subset
[    3.862655] usbcore: registered new interface driver zaurus
[    3.868497] usbcore: registered new interface driver cdc_ncm
[    3.874195] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.880768] ehci-pci: EHCI PCI platform driver
[    3.885459] ehci-orion: EHCI orion driver
[    3.889600] orion-ehci f1058000.usb: EHCI Host Controller
[    3.895036] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[    3.895465] ata1: SATA link down (SStatus 0 SControl 300)
[    3.895499] ata2: SATA link down (SStatus 0 SControl 300)
[    3.913574] orion-ehci f1058000.usb: irq 50, io mem 0xf1058000
[    3.935438] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[    3.941427] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    3.948257] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.955518] usb usb1: Product: EHCI Host Controller
[    3.960417] usb usb1: Manufacturer: Linux 3.10.105.15 ehci_hcd
[    3.966280] usb usb1: SerialNumber: f1058000.usb
[    3.971668] hub 1-0:1.0: USB hub found
[    3.975476] hub 1-0:1.0: 1 port detected
[    3.980170] xhci-hcd f10f0000.usb3: xHCI Host Controller
[    3.985534] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
[    3.993527] xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000
[    3.999358] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    4.006191] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.013446] usb usb2: Product: xHCI Host Controller
[    4.018358] usb usb2: Manufacturer: Linux 3.10.105.15 xhci-hcd
[    4.024216] usb usb2: SerialNumber: f10f0000.usb3
[    4.029677] hub 2-0:1.0: USB hub found
[    4.033458] hub 2-0:1.0: 1 port detected
[    4.037589] xhci-hcd f10f0000.usb3: xHCI Host Controller
[    4.042938] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
[    4.050520] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003
[    4.057349] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.064603] usb usb3: Product: xHCI Host Controller
[    4.069509] usb usb3: Manufacturer: Linux 3.10.105.15 xhci-hcd
[    4.075367] usb usb3: SerialNumber: f10f0000.usb3
[    4.080811] hub 3-0:1.0: USB hub found
[    4.084589] hub 3-0:1.0: 1 port detected
[    4.088730] xhci-hcd f10f8000.usb3: xHCI Host Controller
[    4.094076] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
[    4.135640] xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000
[    4.141447] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[    4.148281] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.155541] usb usb4: Product: xHCI Host Controller
[    4.160441] usb usb4: Manufacturer: Linux 3.10.105.15 xhci-hcd
[    4.166304] usb usb4: SerialNumber: f10f8000.usb3
[    4.172019] hub 4-0:1.0: USB hub found
[    4.175810] hub 4-0:1.0: 1 port detected
[    4.179879] xhci-hcd f10f8000.usb3: xHCI Host Controller
[    4.185221] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
[    4.192797] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003
[    4.199625] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.206884] usb usb5: Product: xHCI Host Controller
[    4.211783] usb usb5: Manufacturer: Linux 3.10.105.15 xhci-hcd
[    4.217651] usb usb5: SerialNumber: f10f8000.usb3
[    4.223667] hub 5-0:1.0: USB hub found
[    4.227457] hub 5-0:1.0: 1 port detected
[    4.232759] mv-udc f1058100.udc: successful probe UDC device without clock gating.
[    4.242010] mousedev: PS/2 mouse device common for all mice
[    4.251801] mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0
[    4.435474] usb 3-1: new SuperSpeed USB device number 2 using xhci-hcd
[    4.455850] usb 3-1: Parent hub missing LPM exit latency info.  Power management will be impacted.
[    4.465697] usb 3-1: New USB device found, idVendor=13fe, idProduct=5200
[    4.472430] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.479606] usb 3-1: Product: 2303 Boot ROM           
[    4.484767] usb 3-1: Manufacturer: Phison                  
[    4.602539] lm75 0-0049: hwmon0: sensor 'lm75'
[    4.656697] armada_thermal f10e4078.thermal: Overheat threshold between 92..107
[    4.665749] orion_wdt: Initial timeout 171 sec
[    4.670618] thecus_event : started
[    4.674041] md: linear personality registered for level -1
[    4.679567] md: raid0 personality registered for level 0
[    4.684901] md: raid1 personality registered for level 1
[    4.690246] md: raid10 personality registered for level 10
[    4.695762] md: raid6 personality registered for level 6
[    4.701095] md: raid5 personality registered for level 5
[    4.706435] md: raid4 personality registered for level 4
[    4.711767] md: multipath personality registered for level -4
[    4.718219] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[    4.726815] dm_crypt using the OCF package.
[    4.731483] device-mapper: multipath: version 1.6.0 loaded
[    4.737023] device-mapper: multipath round-robin: version 1.0.0 loaded
[    4.743581] device-mapper: multipath queue-length: version 0.1.0 loaded
[    4.750231] device-mapper: multipath service-time: version 0.2.0 loaded
[    4.772123] cpuidle: using governor ladder
[    4.776420] armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2
[    4.785819] armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: int_coalescing(1)
[    4.794919] armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources threshold 0x2, threshold_time 0xfffff
[    4.804772] mvCesaInit: channels=2, session=640, queue=256
[    4.830253] armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode
[    4.840110] cesadev_init(c0937940)
[    4.845739] usbcore: registered new interface driver usbhid
[    4.851343] usbhid: USB HID core driver
[    4.855857] Loading Marvell spi device
[    4.862574] arp_tables: (C) 2002 David S. Miller
[    4.867306] TCP: cubic registered
[    4.870641] Initializing XFRM netlink socket
[    4.877541] NET: Registered protocol family 10
[    4.883838] sit: IPv6 over IPv4 tunneling driver
[    4.890329] NET: Registered protocol family 17
[    4.894831] NET: Registered protocol family 15
[    4.899423] Bridge firewalling registered
[    4.903553] 8021q: 802.1Q VLAN Support v1.8
[    4.907824] Key type dns_resolver registered
[    4.912373] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    4.948577] regulator-dummy: disabling
[    4.967230] UBI: attaching mtd0 to ubi0
[    6.632299] UBI: scanning is finished
[    6.646082] UBI warning: print_rsvd_warning: cannot reserve enough PEBs for bad PEB handling, reserved 47, need 71
[    6.714708] UBI: attached mtd0 (name "ubifs", size 512 MiB) to ubi0
[    6.721073] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    6.727912] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    6.734695] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    6.741642] UBI: good PEBs: 4087, bad PEBs: 9, corrupted PEBs: 0
[    6.747687] UBI: user volume: 4, internal volumes: 1, max. volumes count: 128
[    6.754913] UBI: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 1342395426
[    6.764046] UBI: available PEBs: 0, total reserved PEBs: 4087, PEBs reserved for bad PEB handling: 47
[    6.773868] UBI: background thread "ubi_bgt0d" started, PID 1532
[    7.005860] mvebu-rtc f10a3800.rtc: setting system clock to 2025-12-24 14:16:36 UTC (1766585796)
[    7.069937] Freeing unused kernel memory: 272K (c0917000 - c095b000)
starting pid 1627, tty '': '/etc/rc.d/rc.sysinit'
Mounting /proc
Remounting root device read-write...
Mounting other local filesystems...
/var                     : successfully mounted
/dev/pts                 : successfully mounted
/proc                    : already mounted
/sys                     : successfully mounted
Mounting /var under /dev/shm...
[    7.387234] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    7.405793] uhci_hcd: USB Universal Host Controller Interface driver
[    7.471212] usb-storage 3-1:1.0: USB Mass Storage device detected
[    7.490679] scsi2 : usb-storage 3-1:1.0
[    7.511524] usbcore: registered new interface driver usb-storage
[    7.597385] UBIFS: background thread "ubifs_bgt0_3" started, PID 1749
[    7.647533] UBIFS: mounted UBI device 0, volume 3, name "rom"
[    7.653311] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    7.662501] UBIFS: FS size: 401498112 bytes (382 MiB, 3162 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    7.672466] UBIFS: reserved for root: 0 bytes (0 KiB)
[    7.677549] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 2B0AA742-5411-4988-B342-2DF8A11078C2, small LPT model
[    7.697901] UBIFS: background thread "ubifs_bgt0_3" stops
Setting up loopback networking...
[    7.945562] UBIFS: background thread "ubifs_bgt0_2" started, PID 1769
[    8.004870] UBIFS: mounted UBI device 0, volume 2, name "etc"
[    8.010668] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    8.019854] UBIFS: FS size: 8126464 bytes (7 MiB, 64 LEBs), journal size 1650688 bytes (1 MiB, 13 LEBs)
[    8.029295] UBIFS: reserved for root: 0 bytes (0 KiB)
[    8.034371] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 19DE1F75-8119-4293-BAE6-068A80F2F200, small LPT model
[    8.102018] UBIFS: background thread "ubifs_bgt0_4" started, PID 1777
[    8.153911] UBIFS: mounted UBI device 0, volume 4, name "version"
[    8.160072] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    8.169272] UBIFS: FS size: 6094848 bytes (5 MiB, 48 LEBs), journal size 1396736 bytes (1 MiB, 11 LEBs)
[    8.178729] UBIFS: reserved for root: 0 bytes (0 KiB)
[    8.183816] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 8A43601A-8B91-47F3-89A8-2D52E4A458F3, small LPT model
[    8.319271] eth0: mac address changed
[    8.496027] scsi 2:0:0:0: Direct-Access              2303 PRAM        1.00 PQ: 0 ANSI: 0 CCS
[    8.511830] Thecus Tray: 23, sdw
[    8.561617] sd 2:0:0:0: [sdw] Attached SCSI removable disk
[    8.567159] DISK_ADD sdw 23
[    8.569973] 
[    8.572173] criticalevent_user: disk_add sdw 23 
starting pid 1880, tty '': '/sbin/console'

(none) login: ['', '', '']
('rsync_service', {'status': '1'})
('web_service', {'status': '1'})
('webdav', {'status': '1'})
('awss3', {'status': '1'})
('snmp_service', {'status': '1'})
TELNET 0
('itunes_service', {'status': '1'})
('ha', {'status': '0'})
('ssd_cache', {'status': '0'})
('upnpd', {'status': '1'})
OpenVPN_Client 0
('sed', {'status': '1'})
SWAP 0
('tftp', {'status': '1'})
('vpn_server', {'status': '1'})
('swift', {'status': '0'})
('stack', {'status': '1'})
('auto_upgrade', {'status': '1'})
('ftp', {'status': '1'})
Remote_UPS_Monitor 1
('failover', {'status': '1'})
('iso_mount', {'status': '1'})
('nfs', {'status': '1'})
('scale_out', {'status': '0'})
Bonjour 0
('disk_clone_wipe', {'status': '1'})
('ssh_service', {'status': '1'})
IHM 1
('cloud_backup', {'status': '0'})
Snapshot 1
('iscsi', {'status': '1'})
>>>>>>>>>>>>>>>>>>>>Start: Initial LCM

<<<<<<<<<<<<<<<<<<<<End: Initial LCM

>>>>>>>>>>>>>>>>>>>>Start: Load Drivers

modprobe: FATAL: Module i915 not found.
modprobe: FATAL: Module e1000e not found.
modprobe: FATAL: Module igb not found.
modprobe: FATAL: Module ixgbe not found.
modprobe: FATAL: Module tehuti not found.
modprobe: FATAL: Module i40e not found.
modprobe: FATAL: Module bnx2x not found.
modprobe: FATAL: Module tn40xx not found.
modprobe: FATAL: Module tn4022 not found.
modprobe: FATAL: Module be2net not found.
modprobe: FATAL: Module tg3 not found.
[   15.532205] usbcore: registered new interface driver usblp
[   15.573157] NTFS driver 2.1.30 [Flags: R/O MODULE].
[   15.640295] sd 2:0:0:0: Attached scsi generic sg23 type 0
[   15.682197] exFAT: Version 1.2.9
<<<<<<<<<<<<<<<<<<<<End: Load Dr[   15.773913] Clear Critical Queue. 
ivers

>>>>>>>>>>>>>>>>>>>>Start: Initial Settings

Alarm off
<<<<<<<<<<<<<<<<<<<<End: Initial Settings

>>>>>>>>>>>>>>>>>>>>Start: Check Reset to Default

<<<<<<<<<<<<<<<<<<<<End: Check Reset to Defaul[   16.526575] udev: starting version 151
t

>>>>>>>>>>>>>>>>>>>>Start: Config Management

<<<<<<<<<<<<<<<<<<<<End: Config Management

>>>>>>>>>>>>>>>>>>>>Start: Network Initialize

[   20.573946] pool #0: pkt_size=1536, buf_size=1600 - 2048 of 2048 buffers added
[   20.581556] eth0: started
[   20.584362] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
<<<<<<<<<<<<<<<<<<<<End: Network Initialize

>>>>>>>>>>>>>>>>>>>>Start: Unlock SED Disk

<<<<<<<<<<<<<<<<<<<<End: Unlock SED Disk

>>>>>>>>>>>>>>>>>>>>Start: Initial Disk

<<<<<<<<<<<<<<<<<<<<End: Initial Disk

>>>>>>>>>>>>>>>>>>>>Start: Factory Test

2025-12-24 15:17:04,700 - ERROR - DISKMANAGER - get_disk_filesystem sdw fail
<<<<<<<<<<<<<<<<<<<<End: Factory Test

>>>>>>>>>>>>>>>>>>>>Start: Assemble RAID

<<<<<<<<<<<<<<<<<<<<End: Assemble RAID

>>>>>>>>>>>>>>>>>>>>Start: Upgrade Firmware Version

<<<<<<<<<<<<<<<<<<<<End: Upgrade Firmware Version

>>>>>>>>>>>>>>>>>>>>Start: Activate Monitor

<<<<<<<<<<<<<<<<<<<<End: Activate Monitor

>>>>>>>>>>>>>>>>>>>>Start: Environment Setting

<<<<<<<<<<<<<<<<<<<<End: Environment Setting

>>>>>>>>>>>>>>>>>>>>Start: Start Service

[   39.877707] Rounding down aligned max_sectors from 4294967295 to 4294967288
[   42.199118] Loading iSCSI transport class v2.0-870.
[   43.442846] ip_tables: (C) 2000-2006 Netfilter Core Team
2025-12-24 15:17:15,080 - WARNING - UPnPService - DB status value is not 1, abort start upnpd service
2025-12-24 15:17:15,522 - ERROR - SSDCacheManager - Fail to load necessary kernel modules.
      cmd = /sbin/modprobe enhanceio
exit_code = 1
   output = 

<<<<<<<<<<<<<<<<<<<<End: Start Service

>>>>>>>>>>>>>>>>>>>>Start: Boot OK

/bin/sh: /usr/bin/sounds/startupsound: No such file or directory
2025-12-24 15:17:21,215 - WARNING - WebDAVService - WebDAV is not process, please start WebDAV first
<<<<<<<<<<<<<<<<<<<<End: Boot OK

>>>>>>>>>>>>>>>>>>>>Boot Process Successful<<<<<<<<<<<<<<<<<<<<

>>>>>>>>>>>>>>>>>>>>Boot Process Finish<<<<<<<<<<<<<<<<<<<<

Could you please take a look? I don't understand why it's refure to boot Debian from USB.

Changed line in the script thecus-n2350-boot-script-tld-5.sh

fw_setenv set_bootargs 'setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=armada-nand:-(ubifs);spi1.0:0x00400000(uboot),0x00010000@0x00100000(uboot_env),0x00010000@0x00300000(uboot_scr) earlyprintk=serial"'

to

fw_setenv set_bootargs 'setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=pxa3xx_nand-0:-(ubifs);spi1.0:0x00400000(uboot),0x00010000@0x00100000(uboot_env),0x00010000@0x00300000(uboot_scr) earlyprintk=serial"'

and now it tells me that

device usb 0:1
** No partition table - usb 0 **
device usb 1:1
** Bad device usb 1 **
device usb 2:1
** Bad device usb 2 **
device usb 3:1
** Bad device usb 3 **
device usb 4:1
** Bad device usb 4 **
device usb 5:1
** Bad device usb 5 **
device usb 6:1
** Bad device usb 6 **
device usb 7:1
** Bad device usb 7 **
Scan device scsi

Reset SCSI
AHCI init for unit0
SATA link 0 timeout.
SATA link 1 timeout.

Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found
scanning bus for devices...
Found 0 device(s).
device scsi 0:1
** Bad device scsi 0 **
device scsi 1:1
** Bad device scsi 1 **
device scsi 2:1
** Bad device scsi 2 **
device scsi 3:1
** Bad device scsi 3 **
device scsi 4:1
** Bad device scsi 4 **
device scsi 5:1
** Bad device scsi 5 **
device scsi 6:1
** Bad device scsi 6 **
device scsi 7:1
** Bad device scsi 7 **
Booting from usb 0:1 …
loading uImage ...
** No partition table - usb 0 **
Booting stock ...
(Re)start USB...

how is it possible, that there is no partition table? I created one ext3 partition according the article https://forum.doozan.com/read.php?2,32146,32146#msg-32146 on my USB drive. And populated it with data.

In stock firmware fw_printenv command gives that:

boot_config=setenv devices "usb scsi"; setenv bootdev usb; setenv device 0:1; setenv disks "0 1 2 3 4 5 6 7";
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start";  setenv scan_scsi "scsi reset"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$de
kernel_config=setenv load_dtb_addr 0x1000000; setenv load_initrd_addr 0x3000000; setenv load_image_addr 0x02000000; setenv dtb_file /boot/dts/armada-385-thecus-n2350.dtb
load_image=echo loading uImage ...; ext2load $bootdev $device $load_image_addr /boot/uImage
load_dtb=echo loading DTB $dtb_file ...; ext2load $bootdev $device $load_dtb_addr $dtb_file
load_initrd=echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd
set_bootargs=setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=pxa3xx_nand-0:-(ubifs);spi1.0:0x00400000(uboot),0x00010000@0x00100000(uboot_env),0x00010000@0x00300000(uboot_s"
set_bootargs_stock=setenv bootargs "root=/dev/ram0 rw max_loop=210 console=ttyS0,115200 init=sbin/init rootdelay=3 ubi.mtd=0 mtdparts=armada-nand:-(ubifs);spi_flash:0x00400000(uboot),0x00010000@0x00100"
bootcmd_exec=echo Booting from $bootdev $device …; setenv fdt_skip_update yes; setenv initrd_high 0xffffffff; if run load_image; then if run load_initrd; then bootm $load_image_addr $load_initrd_addr; i
bootcmd_custom=run boot_config; run kernel_config; run scan_disk; run set_bootargs; run bootcmd_exec
bootcmd=echo Booting Debian ...; run bootcmd_custom; echo Booting stock ...; run set_bootargs_stock; usb reset; if fatload usb 0:1 0x2000000 rescue_fw/rescue_fw.img;then imi 0x2000000;source 0x2000000;0

Then I decreased root volume space to 8Gbyte but still no luck

Hit any key to stop autoboot:  0 
Marvell>> usb start
(Re)start USB...
USB0:   Port (usbActive) : 0    Interface (usbType = 3) : Anson:xhci_usb_lowlevel_init--1--index=0
Anson:xhci_usb_lowlevel_init--2
Anson:Register 2000120 NbrPorts 2
USB XHCI 1.00
Anson:xhci_usb_lowlevel_init--3
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
       scanning usb for ethernet devices... 0 Ethernet Device(s) found
Marvell>> usb info
1: Hub,  USB Revision 3.0
 - u-boot XHCI Host Controller 
 - Class: Hub
 - PacketSize: 9  Configurations: 1
 - Vendor: 0x0000  Product 0x0000 Version 1.0
   Configuration: 1
   - Interfaces: 1 Self Powered 0mA
     Interface: 0
     - Alternate Setting 0, Endpoints: 1
     - Class Hub
     - Endpoint 1 In Interrupt MaxPacket 8 Interval 255ms

2: Mass Storage,  USB Revision 3.0
 - UFD 3.0 Silicon-Power32G 14008062031E600442B24C6CB05
 - Class: (from Interface) Mass Storage
 - PacketSize: 9  Configurations: 1
 - Vendor: 0x13fe  Product 0x5200 Version 1.0
   Configuration: 1
   - Interfaces: 1 Bus Powered 126mA
     Interface: 0
     - Alternate Setting 0, Endpoints: 2
     - Class Mass Storage, Transp. SCSI, Bulk only
     - Endpoint 1 In Bulk MaxPacket 1024
     - Endpoint 2 Out Bulk MaxPacket 1024

Marvell>> usb storage
  Device 0: Vendor: UFD 3.0  Rev: PMAP Prod: Silicon-Power32G
            Type: Removable Hard Disk
            Capacity: 30176.0 MB = 29.4 GB (61800448 x 512)
Marvell>> ext2ls usb 0
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **

ext2ls usb 0
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
Marvell>> ext2ls usb 0:1
** No partition table - usb 0 **

Edited 4 time(s). Last edit at 12/24/2025 12:16PM by Nikola204.

Sooooo....I made it! Now I'm looking at the Debian's console, but the problem was in USB Drive! I changed USB 3 to USB 2 drive and did the same steps according to the manual. And now everything works!
So Bodhi, could you please add that info about USB 2 to your manual too ?

For now I'm getting such log. Is everything fine there?

BootROM - 1.73
Booting from SPI flash


General initialization - Version: 1.0.0
AVS selection from EFUSE disabled (Skip reading EFUSE values)
Overriding default AVS value to: 0x23
Detected Device ID 6820
High speed PHY - Version: 2.0

Init Customer board board SerDes lanes topology details:
 | Lane # | Speed|    Type     |
 ------------------------------|
 |   0    |  0   |  SGMII0     |
 |   1    |  3   |  SATA0      |
 |   2    |  3   |  SATA1      |
 |   4    |  5   |  USB3 HOST0 |
 |   5    |  5   |  USB3 HOST1 |
 -------------------------------
High speed PHY - Ended Successfully
DDR4 Training Sequence - Ver TIP-0.23.(Sublib 0.8)0
DDR4 Training Sequence - Switching XBAR Window to FastPath Window 
DDR4 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED

 __   __                      _ _
|  \/  | __ _ _ ____   _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| |  | | (_| | |   \ V /  __/ | |
|_|  |_|\__,_|_|    \_/ \___|_|_|
         _   _     ____              _
        | | | |   | __ )  ___   ___ | |_ 
        | | | |___|  _ \ / _ \ / _ \| __| 
        | |_| |___| |_) | (_) | (_) | |_ 
         \___/    |____/ \___/ \___/ \__| 
 ** LOADER **


U-Boot 2013.01 (Nov 12 2018 - 20:56:19) Marvell version: 2015_T1.0p18-tld-4

Board: A38x-Customer0-Thecus-N2350
SoC:   MV88F6820 Rev A0
       running 2 CPUs
CPU:   ARM Cortex A9 MPCore (Rev 1) LE
       CPU 0
       CPU    @ 1066 [MHz]
       L2     @ 800 [MHz]
       TClock @ 200 [MHz]
       DDR4    @ 800 [MHz]
       DDR4 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM:  1 GiB
NAND:  512 MiB
MMC:   mv_sdh: 0
SF: Detected MX25L3205D with page size 64 KiB, total 4 MiB
USB2.0 0: Host Mode
USB3.0 0: Host Mode
USB3.0 1: Host Mode

Map:   Code:                    0x3fed4000:0x3ff9659c
       BSS:                     0x3ffeff24
       Stack:                   0x3f9c3f20
       Heap:                    0x3f9c4000:0x3fed4000
       U-Boot Environment:      0x00100000:0x00110000 (SPI)

Board configuration detected:
Net:   
|  port  | Interface | PHY address  |
|--------|-----------|--------------|
| egiga0 |   SGMII   |     0x01     |
egiga0 [PRIME]
Hit any key to stop autoboot:  0 
Booting Debian ...
running scan_disk ...
Scan device usb
(Re)start USB...
USB0:   Port (usbActive) : 0    Interface (usbType = 3) : Anson:xhci_usb_lowlevel_init--1--index=0
Anson:xhci_usb_lowlevel_init--2
Anson:Register 2000120 NbrPorts 2
USB XHCI 1.00
Anson:xhci_usb_lowlevel_init--3
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
       scanning usb for ethernet devices... 0 Ethernet Device(s) found
device usb 0:1
** File not found /boot/zImage **
device usb 1:1
** Bad device usb 1 **
device usb 2:1
** Bad device usb 2 **
device usb 3:1
** Bad device usb 3 **
device usb 4:1
** Bad device usb 4 **
device usb 5:1
** Bad device usb 5 **
device usb 6:1
** Bad device usb 6 **
device usb 7:1
** Bad device usb 7 **
Scan device scsi

Reset SCSI
AHCI init for unit0
SATA link 0 timeout.
SATA link 1 timeout.

Error: SCSI Controller(s) 1B4B:9215 1B4B:9235 not found
scanning bus for devices...
Found 0 device(s).
device scsi 0:1
** Bad device scsi 0 **
device scsi 1:1
** Bad device scsi 1 **
device scsi 2:1
** Bad device scsi 2 **
device scsi 3:1
** Bad device scsi 3 **
device scsi 4:1
** Bad device scsi 4 **
device scsi 5:1
** Bad device scsi 5 **
device scsi 6:1
** Bad device scsi 6 **
device scsi 7:1
** Bad device scsi 7 **
Booting from usb 0:1 …
loading uImage ...
5200702 bytes read in 502 ms (9.9 MiB/s)
loading uInitrd ...
5257173 bytes read in 554 ms (9 MiB/s)
## Booting kernel from Legacy Image at 02000000 ...
   Image Name:   Linux-6.6.2-mvebu-tld-1
   Created:      2025-12-13  13:54:35 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    5200638 Bytes = 5 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 03000000 ...
   Image Name:   initramfs-6.6.2-mvebu-tld-1
   Created:      2023-12-12  22:03:52 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    5257109 Bytes = 5 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

[    0.000000][    T0] Booting Linux on physical CPU 0x0
[    0.000000][    T0] Linux version 6.6.2-mvebu-tld-1 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Mon Nov 20 18:44:27 PST 2023
[    0.000000][    T0] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
[    0.000000][    T0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000][    T0] OF: fdt: Machine model: Thecus N2350
[    0.000000][    T0] printk: bootconsole [earlycon0] enabled
[    0.000000][    T0] Memory policy: Data cache writealloc
[    0.000000][    T0] Zone ranges:
[    0.000000][    T0]   Normal   [mem 0x0000000000000000-0x000000002fffffff]
[    0.000000][    T0]   HighMem  [mem 0x0000000030000000-0x000000003fffffff]
[    0.000000][    T0] Movable zone start for each node
[    0.000000][    T0] Early memory node ranges
[    0.000000][    T0]   node   0: [mem 0x0000000000000000-0x000000003fffffff]
[    0.000000][    T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
[    0.000000][    T0] percpu: Embedded 29 pages/cpu s25364 r8192 d85228 u118784
[    0.000000][    T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=pxa3xx_nand-0:-(ubifs);spi1.0:0x00400000(uboot),0x00010000@0x00100000(uboot_env),0x00010000@0x00l
[    0.000000][    T0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[    0.000000][    T0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000][    T0] Built 1 zonelists, mobility grouping on.  Total pages: 260416
[    0.000000][    T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[    0.000000][    T0] Memory: 1014332K/1048576K available (10240K kernel code, 873K rwdata, 3492K rodata, 1024K init, 314K bss, 34244K reserved, 0K cma-reserved, 262144K highmem)
[    0.000000][    T0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000][    T0] rcu: Preemptible hierarchical RCU implementation.
[    0.000000][    T0] rcu:     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000][    T0]  Trampoline variant of Tasks RCU enabled.
[    0.000000][    T0]  Tracing variant of Tasks RCU enabled.
[    0.000000][    T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000][    T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000][    T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000][    T0] L2C: DT/platform modifies aux control register: 0x06070000 -> 0x16070000
[    0.000000][    T0] L2C-310 enabling early BRESP for Cortex-A9
[    0.000000][    T0] L2C-310 full line of zeros enabled for Cortex-A9
[    0.000000][    T0] L2C-310 D prefetch enabled, offset 1 lines
[    0.000000][    T0] L2C-310 dynamic clock gating enabled, standby mode enabled
[    0.000000][    T0] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
[    0.000000][    T0] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
[    0.000000][    T0] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000002][    T0] sched_clock: 64 bits at 533MHz, resolution 1ns, wraps every 2199023255551ns
[    0.008684][    T0] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x7aed16d152, max_idle_ns: 440795225656 ns
[    0.020392][    T0] Switching to timer-based delay loop, resolution 1ns
[    0.027293][    T0] Ignoring duplicate/late registration of read_current_timer delay
[    0.035010][    T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[    0.046971][    T0] kfence: initialized - using 2097152 bytes for 255 objects at 0x(ptrval)-0x(ptrval)
[    0.056652][    T0] Console: colour dummy device 80x30
[    0.061816][    T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 1066.00 BogoMIPS (lpj=5330000)
[    0.073097][    T0] CPU: Testing write buffer coherency: ok
[    0.078690][    T0] CPU0: Spectre v2: using BPIALL workaround
[    0.084415][    T0] pid_max: default: 32768 minimum: 301
[    0.093759][    T0] LSM: initializing lsm=capability,integrity
[    0.100760][    T0] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.108750][    T0] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.122308][    T1] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.129782][    T1] RCU Tasks: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1.
[    0.137635][    T1] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1.
[    0.145977][    T1] Setting up static identity map for 0x100000 - 0x100060
[    0.153174][    T1] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
[    0.159174][    T1] mvebu-pmsu: Initializing Power Management Service Unit
[    0.166190][    T1] rcu: Hierarchical SRCU implementation.
[    0.171672][    T1] rcu:     Max phase no-delay instances is 1000.
[    0.178421][    T1] smp: Bringing up secondary CPUs ...
[    0.184124][    T1] Booting CPU 1
[    0.187662][    T0] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.187677][    T0] CPU1: Spectre v2: using BPIALL workaround
[    0.199867][    T1] smp: Brought up 1 node, 2 CPUs
[    0.204646][    T1] SMP: Total of 2 processors activated (2132.00 BogoMIPS).
[    0.211683][    T1] CPU: All CPU(s) started in SVC mode.
[    0.218446][    T1] devtmpfs: initialized
[    0.228153][    T1] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.236833][    T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.247379][    T1] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[    0.257611][    T1] prandom: seed boundary self test passed
[    0.265153][    T1] prandom: 100 self tests passed
[    0.269945][    T1] pinctrl core: initialized pinctrl subsystem
[    0.277489][    T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.285018][    T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.295450][    T1] audit: initializing netlink subsys (disabled)
[    0.301758][   T30] audit: type=2000 audit(0.250:1): state=initialized audit_enabled=0 res=1
[    0.302361][    T1] thermal_sys: Registered thermal governor 'step_wise'
[    0.310257][    T1] cpuidle: using governor ladder
[    0.321736][    T1] cpuidle: using governor menu
[    0.326529][    T1] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.335213][    T1] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.345191][    T1] platform soc: Fixed dependency cycle(s) with /soc/internal-regs/interrupt-controller@d000
[    0.537163][    T1] raid6: int32x8  gen()   213 MB/s
[    0.707158][    T1] raid6: int32x4  gen()   222 MB/s
[    0.877133][    T1] raid6: int32x2  gen()   367 MB/s
[    1.047077][    T1] raid6: int32x1  gen()   424 MB/s
[    1.052024][    T1] raid6: using algorithm int32x1 gen() 424 MB/s
[    1.227166][    T1] raid6: .... xor() 164 MB/s, rmw enabled
[    1.232720][    T1] raid6: using intx1 recovery algorithm
[    1.239635][    T1] SCSI subsystem initialized
[    1.244507][    T1] usbcore: registered new interface driver usbfs
[    1.250755][    T1] usbcore: registered new interface driver hub
[    1.256777][    T1] usbcore: registered new device driver usb
[    1.262857][    T1] pps_core: LinuxPPS API ver. 1 registered
[    1.268515][    T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.278330][    T1] PTP clock support registered
[    1.284730][    T1] vgaarb: loaded
[    1.288662][    T1] clocksource: Switched to clocksource arm_global_timer
[    1.299863][    T1] VFS: Disk quotas dquot_6.6.0
[    1.304690][    T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.322642][    T1] NET: Registered PF_INET protocol family
[    1.328399][    T1] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    1.338198][    T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    1.347312][    T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    1.355805][    T1] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    1.364315][    T1] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[    1.372385][    T1] TCP: Hash tables configured (established 8192 bind 8192)
[    1.379801][    T1] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear)
[    1.388074][    T1] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    1.395411][    T1] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    1.403629][    T1] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    1.410643][    T1] RPC: Registered named UNIX socket transport module.
[    1.417239][    T1] RPC: Registered udp transport module.
[    1.422641][    T1] RPC: Registered tcp transport module.
[    1.428019][    T1] RPC: Registered tcp-with-tls transport module.
[    1.434184][    T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.441314][    T1] PCI: CLS 0 bytes, default 64
[    1.446161][   T25] Trying to unpack rootfs image as initramfs...
[    1.452734][    T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
[    1.472828][    T1] Initialise system trusted keyrings
[    1.478057][    T1] Key type blacklist registered
[    1.483038][    T1] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[    1.490273][    T1] zbud: loaded
[    1.502089][    T1] NFS: Registering the id_resolver key type
[    1.507877][    T1] Key type id_resolver registered
[    1.512822][    T1] Key type id_legacy registered
[    1.517678][    T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.525118][    T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[    1.639952][    T1] xor: measuring software checksum speed
[    1.651156][    T1]    arm4regs        :  1738 MB/sec
[    1.663579][    T1]    8regs           :  1335 MB/sec
[    1.675725][    T1]    32regs          :  1386 MB/sec
[    1.680775][    T1] xor: using function: arm4regs (1738 MB/sec)
[    1.685404][   T25] Freeing initrd memory: 5136K
[    1.686696][    T1] async_tx: api initialized (async)
[    1.696386][    T1] Key type asymmetric registered
[    1.701185][    T1] Asymmetric key parser 'x509' registered
[    1.707080][    T1] bounce: pool size: 64 pages
[    1.711990][    T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[    1.720478][    T1] io scheduler bfq registered
[    1.729299][    T1] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
[    1.739373][    T1] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
[    1.749527][    T1] debugfs: Directory 'f1018100.gpio' with parent 'regmap' already present!
[    1.758839][    T1] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation.
[    1.768878][    T1] debugfs: Directory 'f1018140.gpio' with parent 'regmap' already present!
[    1.778923][    T1] mvebu-pcie soc:pcie: host bridge /soc/pcie ranges:
[    1.785487][    T1] mvebu-pcie soc:pcie:      MEM 0x00f1080000..0x00f1081fff -> 0x0000080000
[    1.793956][    T1] mvebu-pcie soc:pcie:      MEM 0x00f1040000..0x00f1041fff -> 0x0000040000
[    1.802450][    T1] mvebu-pcie soc:pcie:      MEM 0x00f1044000..0x00f1045fff -> 0x0000044000
[    1.810891][    T1] mvebu-pcie soc:pcie:      MEM 0x00f1048000..0x00f1049fff -> 0x0000048000
[    1.819326][    T1] mvebu-pcie soc:pcie:      MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[    1.828270][    T1] mvebu-pcie soc:pcie:       IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[    1.837227][    T1] mvebu-pcie soc:pcie:      MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[    1.846180][    T1] mvebu-pcie soc:pcie:       IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[    1.855132][    T1] mvebu-pcie soc:pcie:      MEM 0xffffffffffffffff..0x00fffffffe -> 0x0300000000
[    1.864083][    T1] mvebu-pcie soc:pcie:       IO 0xffffffffffffffff..0x00fffffffe -> 0x0300000000
[    1.873034][    T1] mvebu-pcie soc:pcie:      MEM 0xffffffffffffffff..0x00fffffffe -> 0x0400000000
[    1.881977][    T1] mvebu-pcie soc:pcie:       IO 0xffffffffffffffff..0x00fffffffe -> 0x0400000000
[    1.891723][    T1] mvebu-pcie soc:pcie: PCI host bridge to bus 0000:00
[    1.898324][    T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[    1.904511][    T1] pci_bus 0000:00: root bus resource [mem 0xf1080000-0xf1081fff] (bus address [0x00080000-0x00081fff])
[    1.915395][    T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff])
[    1.926237][    T1] pci_bus 0000:00: root bus resource [mem 0xf1044000-0xf1045fff] (bus address [0x00044000-0x00045fff])
[    1.937077][    T1] pci_bus 0000:00: root bus resource [mem 0xf1048000-0xf1049fff] (bus address [0x00048000-0x00049fff])
[    1.947913][    T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[    1.955470][    T1] pci_bus 0000:00: root bus resource [io  0x1000-0xeffff]
[    1.962552][    T1] pci 0000:00:01.0: [11ab:6820] type 01 class 0x060400
[    1.969898][    T1] pci 0000:00:02.0: [11ab:6820] type 01 class 0x060400
[    1.978528][    T1] PCI: bus0: Fast back to back transfers disabled
[    1.984811][    T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.993510][    T1] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    2.002492][    T1] PCI: bus1: Fast back to back transfers enabled
[    2.008688][    T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    2.016309][    T1] PCI: bus2: Fast back to back transfers enabled
[    2.022493][    T1] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[    2.029808][    T1] pci 0000:00:01.0: PCI bridge to [bus 01]
[    2.035457][    T1] pci 0000:00:02.0: PCI bridge to [bus 02]
[    2.042766][    T1] mv_xor f1060800.xor: Marvell shared XOR driver
[    2.129970][    T1] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[    2.141271][    T1] mv_xor f1060900.xor: Marvell shared XOR driver
[    2.209969][    T1] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[    2.331054][    T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    2.343913][    T1] printk: console [ttyS0] disabled
[    2.369978][    T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 41, base_baud = 12500000) is a 16550A
[    2.379673][    T1] printk: console [ttyS0] enabled
[    2.379673][    T1] printk: console [ttyS0] enabled
[    2.389507][    T1] printk: bootconsole [earlycon0] disabled
[    2.389507][    T1] printk: bootconsole [earlycon0] disabled
[    2.420992][    T1] ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator
[    2.429549][    T1] ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator
[    2.437847][    T1] ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator
[    2.446554][    T1] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[    2.456382][    T1] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs 
[    2.467818][    T1] scsi host0: ahci-mvebu
[    2.473229][    T1] scsi host1: ahci-mvebu
[    2.477715][    T1] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 42
[    2.486409][    T1] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 42
[    2.497156][    T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xdc
[    2.504286][    T1] nand: Hynix H27U4G8F2DTR-BC
[    2.508879][    T1] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    2.518189][    T1] Bad block table found at page 261824, version 0x01
[    2.525776][    T1] Bad block table found at page 261760, version 0x01
[    2.532538][    T1] nand_read_bbt: bad block at 0x00000d400000
[    2.538430][    T1] nand_read_bbt: bad block at 0x00001ff80000
[    2.544304][    T1] nand_read_bbt: bad block at 0x00001ffa0000
[    2.550178][    T1] nand_read_bbt: bad block at 0x00001ffc0000
[    2.556043][    T1] nand_read_bbt: bad block at 0x00001ffe0000
[    2.561963][    T1] 1 cmdlinepart partitions found on MTD device pxa3xx_nand-0
[    2.569238][    T1] Creating 1 MTD partitions on "pxa3xx_nand-0":
[    2.575368][    T1] 0x000000000000-0x000020000000 : "ubifs"
[    2.586207][    T1] spi-nor spi1.0: mx25l3205d (4096 Kbytes)
[    2.591983][    T1] 3 cmdlinepart partitions found on MTD device spi1.0
[    2.598640][    T1] Creating 3 MTD partitions on "spi1.0":
[    2.604242][    T1] 0x000000000000-0x000000400000 : "uboot"
[    2.611627][    T1] 0x000000100000-0x000000110000 : "uboot_env"
[    2.619156][    T1] 0x000000300000-0x000000310000 : "uboot_scr"
[    2.627657][    T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[    2.636271][    T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[    2.668142][    T1] hwmon hwmon0: temp1_input not attached to any thermal zone
[    2.677933][    T1] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled
[    2.692813][    T1] mvneta f1070000.ethernet eth0: Using random mac address d2:fa:f5:fb:68:e9
[    2.702462][    T1] usbcore: registered new interface driver smsc75xx
[    2.709497][    T1] orion-ehci f1058000.usb: EHCI Host Controller
[    2.715667][    T1] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[    2.724135][    T1] orion-ehci f1058000.usb: irq 45, io mem 0xf1058000
[    2.758679][    T1] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[    2.765581][    T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.06
[    2.774619][    T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.782596][    T1] usb usb1: Product: EHCI Host Controller
[    2.788203][    T1] usb usb1: Manufacturer: Linux 6.6.2-mvebu-tld-1 ehci_hcd
[    2.795302][    T1] usb usb1: SerialNumber: f1058000.usb
[    2.801489][    T1] hub 1-0:1.0: USB hub found
[    2.806000][    T1] hub 1-0:1.0: 1 port detected
[    2.812223][    T1] xhci-hcd f10f0000.usb3: xHCI Host Controller
[    2.818291][    T1] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
[    2.826676][    T1] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000000010
[    2.830292][  T695] ata2: SATA link down (SStatus 0 SControl 300)
[    2.836738][    T1] xhci-hcd f10f0000.usb3: irq 46, io mem 0xf10f0000
[    2.842852][  T684] ata1: SATA link down (SStatus 0 SControl 300)
[    2.850235][    T1] xhci-hcd f10f0000.usb3: xHCI Host Controller
[    2.861576][    T1] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
[    2.869843][    T1] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed
[    2.877088][    T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.06
[    2.886128][    T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.894104][    T1] usb usb2: Product: xHCI Host Controller
[    2.899721][    T1] usb usb2: Manufacturer: Linux 6.6.2-mvebu-tld-1 xhci-hcd
[    2.906810][    T1] usb usb2: SerialNumber: f10f0000.usb3
[    2.913066][    T1] hub 2-0:1.0: USB hub found
[    2.917575][    T1] hub 2-0:1.0: 1 port detected
[    2.922859][    T1] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.931896][    T1] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.06
[    2.940936][    T1] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.948990][    T1] usb usb3: Product: xHCI Host Controller
[    2.954597][    T1] usb usb3: Manufacturer: Linux 6.6.2-mvebu-tld-1 xhci-hcd
[    2.961702][    T1] usb usb3: SerialNumber: f10f0000.usb3
[    2.967863][    T1] hub 3-0:1.0: USB hub found
[    2.972389][    T1] hub 3-0:1.0: 1 port detected
[    2.978067][    T1] xhci-hcd f10f8000.usb3: xHCI Host Controller
[    2.984159][    T1] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
[    2.992498][    T1] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000000010
[    3.002532][    T1] xhci-hcd f10f8000.usb3: irq 47, io mem 0xf10f8000
[    3.009192][    T1] xhci-hcd f10f8000.usb3: xHCI Host Controller
[    3.015245][    T1] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
[    3.023524][    T1] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed
[    3.030778][    T1] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.06
[    3.039811][    T1] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.047776][    T1] usb usb4: Product: xHCI Host Controller
[    3.053397][    T1] usb usb4: Manufacturer: Linux 6.6.2-mvebu-tld-1 xhci-hcd
[    3.060850][    T1] usb usb4: SerialNumber: f10f8000.usb3
[    3.067056][    T1] hub 4-0:1.0: USB hub found
[    3.071616][    T1] hub 4-0:1.0: 1 port detected
[    3.076860][    T1] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.085949][    T1] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.06
[    3.095144][    T1] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.103218][    T1] usb usb5: Product: xHCI Host Controller
[    3.108863][    T1] usb usb5: Manufacturer: Linux 6.6.2-mvebu-tld-1 xhci-hcd
[    3.115955][    T1] usb usb5: SerialNumber: f10f8000.usb3
[    3.122064][    T1] hub 5-0:1.0: USB hub found
[    3.126644][    T1] hub 5-0:1.0: 1 port detected
[    3.132707][    T1] usbcore: registered new interface driver usblp
[    3.139209][    T1] usbcore: registered new interface driver usb-storage
[    3.146561][    T1] mousedev: PS/2 mouse device common for all mice
[    3.155375][    T1] armada38x-rtc f10a3800.rtc: registered as rtc0
[    3.161823][    T1] armada38x-rtc f10a3800.rtc: setting system clock to 2025-12-24T19:24:05 UTC (1766604245)
[    3.172947][    T1] i2c_dev: i2c /dev entries driver
[    3.178290][    T1] mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recovery not supported
[    3.187650][    T1] mv64xxx_i2c f1011100.i2c: can't get pinctrl, bus recovery not supported
[    3.198646][    T1] gpio-fan fan: GPIO fan initialized
[    3.207111][    T1] orion_wdt: Initial timeout 171 sec
[    3.212351][   T23] usb 2-1: new high-speed USB device number 2 using xhci-hcd
[    3.220485][    T1] device-mapper: uevent: version 1.0.3
[    3.226499][    T1] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com
[    3.236094][    T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[    3.243497][    T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[    3.250971][    T1] device-mapper: multipath service-time: version 0.3.0 loaded
[    3.258415][    T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[    3.265653][    T1] sdhci: Secure Digital Host Controller Interface driver
[    3.272618][    T1] sdhci: Copyright(c) Pierre Ossman
[    3.279119][    T1] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.291085][    T1] marvell-cesa f1090000.crypto: CESA device successfully registered
[    3.299375][    T1] hid: raw HID events driver (C) Jiri Kosina
[    3.306090][    T1] usbcore: registered new interface driver usbhid
[    3.312716][    T1] usbhid: USB HID core driver
[    3.318847][    T1] NET: Registered PF_INET6 protocol family
[    3.325834][   T31] mmc0: SDHCI controller on f10d8000.sdhci [f10d8000.sdhci] using ADMA
[    3.326018][    T1] Segment Routing with IPv6
[    3.338392][    T1] RPL Segment Routing with IPv6
[    3.343423][    T1] In-situ OAM (IOAM) with IPv6
[    3.348156][    T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    3.356211][    T1] NET: Registered PF_PACKET protocol family
[    3.362359][    T1] 8021q: 802.1Q VLAN Support v1.8
[    3.367325][    T1] Key type dns_resolver registered
[    3.372736][    T1] ThumbEE CPU extension supported.
[    3.377740][    T1] Registering SWP/SWPB emulation handler
[    3.412283][   T23] usb 2-1: New USB device found, idVendor=090c, idProduct=1000, bcdDevice=11.00
[    3.425574][    T1] registered taskstats version 1
[    3.436168][    T1] Loading compiled-in X.509 certificates
[    3.442078][   T23] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    3.458999][   T23] usb 2-1: Product: Silicon-Power
[    3.463919][   T23] usb 2-1: Manufacturer: UFD 2.0
[    3.476813][    T1] Key type .fscrypt registered
[    3.481512][   T23] usb 2-1: SerialNumber: 13110502028000000123
[    3.488640][    T1] Key type fscrypt-provisioning registered
[    3.494468][    T1] Key type big_key registered
[    3.499584][   T23] usb-storage 2-1:1.0: USB Mass Storage device detected
[    3.507476][   T23] scsi host2: usb-storage 2-1:1.0
[    3.524763][    T1] Key type encrypted registered
[    3.537150][   T31] usb_phy_generic usb-phy: dummy supplies not allowed for exclusive requests
[    3.547309][    T1] input: keys as /devices/platform/keys/input/input0
[    3.555196][    T1] clk: Disabling unused clocks
[    3.562673][    T1] Freeing unused kernel image (initmem) memory: 1024K
[    3.599500][    T1] Checked W+X mappings: passed, no W+X pages found
[    3.605959][    T1] Run /init as init process
Loading, please wait...
Starting systemd-udevd version 252.19-1~deb12u1
[    4.530059][  T308] scsi 2:0:0:0: Direct-Access     UFD 2.0  Silicon-Power16G 1100 PQ: 0 ANSI: 4
[    4.543108][   T31] sd 2:0:0:0: [sda] 31461376 512-byte logical blocks: (16.1 GB/15.0 GiB)
[    4.554239][   T31] sd 2:0:0:0: [sda] Write Protect is off
[    4.563984][   T31] sd 2:0:0:0: [sda] No Caching mode page found
[    4.578771][   T31] sd 2:0:0:0: [sda] Assuming drive cache: write through
[    4.590191][   T31]  sda: sda1
[    4.590314][ T1327] mtdblock: MTD device 'ubifs' is NAND, please consider using UBI block devices instead.
[    4.593639][   T31] sd 2:0:0:0: [sda] Attached SCSI removable disk
[    4.627352][ T1334] mvneta f1070000.ethernet end0: renamed from eth0
[    4.662773][ T1324] usbcore: registered new interface driver uas
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.38.1
[/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1 
rootfs: clean, 25888/983040 files, 292001/3931898 blocks
done.
[   15.382964][ T1355] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[   15.430614][ T1355] EXT4-fs (sda1): mounted filesystem 22638d6f-70cf-4c2c-9e7a-55ec5d1e5aa9 ro with ordered data mode. Quota mode: none.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 3.06 booting
INIT: No inittab.d directory found
Using makefile-style concurrent boot in runlevel S.
Setting hostname to 'debian'...done.
Starting hotplug events dispatcher: systemd-udevd.
Synthesizing the initial hotplug events (subsystems)...done.
Synthesizing the initial hotplug events (devices)...done.
Waiting for /dev to be fully populated...[   17.860812][ T1546] mtdblock: MTD device 'ubifs' is NAND, please consider using UBI block devices instead.
[   18.103016][ T1543] sd 2:0:0:0: Attached scsi generic sg0 type 0
done.
Activating swap:.
[   19.099522][ T1685] EXT4-fs (sda1): re-mounted 22638d6f-70cf-4c2c-9e7a-55ec5d1e5aa9 r/w. Quota mode: none.
Will now check all file systems.
Checking all file systems.
LABEL=rootfs is mounted
Done checking file systems.
Log is being saved in /var/log/fsck/checkfs if that location is writable.
Cleaning up temporary files...Cleaning /tmp...done.
 /tmp.
Will now mount local filesystems:.
Will now activate swapfile swap, if any:done.
Checking minimum space in /tmp...done.
Cleaning up temporary files....
Starting Setting kernel variables: sysctl.
[   21.208679][    C0] random: crng init done
Initializing random number generator...done.
[   21.325508][ T2047] mvneta f1070000.ethernet eth0: renamed from end0
[   21.729571][ T2077] mvneta f1070000.ethernet eth0: PHY [f1072004.mdio-mii:01] driver [Marvell 88E1510] (irq=POLL)
[   21.740346][ T2077] mvneta f1070000.ethernet eth0: configuring for phy/sgmii link mode
Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.3-P1
Copyright 2004-2022 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/be:e1:af:1c:82:2e
Sending on   LPF/eth0/be:e1:af:1c:82:2e
Sending on   Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 20
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 14
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7
No DHCPOFFERS received.
No working leases in persistent database - sleeping.
done.
Starting RPC port mapper daemon: rpcbind.
Starting NFS common utilities: statd idmapd.
Cleaning up temporary files....
INIT: Entering runlevel: 2
Using makefile-style concurrent boot in runlevel 2.
Not starting NFS kernel daemon: no exports ... (warning).
Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
2213 (syslogd)
.
Starting NTP server: ntpd2025-12-24T11:25:43 ntpd[2233]: INIT: ntpd ntpsec-1.2.2: Starting
2025-12-24T11:25:43 ntpd[2233]: INIT: Command line: /usr/sbin/ntpd -p /run/ntpd.pid -c /etc/ntpsec/ntp.conf -g -N -u ntpsec:ntpsec
.
Starting periodic command scheduler: cron
.
Starting NTP server: ntpd2025-12-24T11:25:43 ntpd[2259]: INIT: ntpd ntpsec-1.2.2: Starting
2025-12-24T11:25:43 ntpd[2259]: INIT: Command line: /usr/sbin/ntpd -p /var/run/ntpd.pid -g -u 104:109
.
Starting OpenBSD Secure Shell server: sshdsshd: no hostkeys available -- exiting.
 failed!
Starting system message bus: dbus.
Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
2235 (klogd)
.
Running local boot scripts (/etc/rc.local)
ssh-keygen: generating new host keys: RSA 
ECDSA ED25519 

Starting OpenBSD Secure Shell server: sshd
.
[   95.807953][ T2298] Setting Persistent MAC address to 00:14:FD:19:C3:96
<13>Dec 24 11:25:54 root[2305]: Setting Persistent MAC address to 00:14:FD:19:C3:96
Killed old client process
Internet Systems Consortium DHCP Client 4.4.3-P1
Copyright 2004-2022 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/be:e1:af:1c:82:2e
Sending on   LPF/eth0/be:e1:af:1c:82:2e
Sending on   Socket/fallback
DHCPRELEASE of 192.168.0.18 on eth0 to 192.168.0.1 port 67
send_packet: Network is unreachable
send_packet: please consult README file regarding broadcast address.
dhclient.c:3124: Failed to send 300 byte long packet over fallback interface.
Internet Systems Consortium DHCP Client 4.4.3-P1
Copyright 2004-2022 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

[   97.189562][ T2337] mvneta f1070000.ethernet eth0: PHY [f1072004.mdio-mii:01] driver [Marvell 88E1510] (irq=POLL)
[   97.248864][ T2337] mvneta f1070000.ethernet eth0: configuring for phy/sgmii link mode
Listening on LPF/eth0/00:14:fd:19:c3:96
Sending on   LPF/eth0/00:14:fd:19:c3:96
Sending on   Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 13
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 21
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11
No DHCPOFFERS received.
No working leases in persistent database - sleeping.
.

Debian GNU/Linux 12 debian ttyS0

debian login: root

I'd like to understand, how to fix these error. Could somebody please help me?

device usb 0:1
** File not found /boot/zImage **

There is only zImage.fdt in /boot folder.

Booting from usb 0:1 …
loading uImage ...
5200702 bytes read in 502 ms (9.9 MiB/s)
loading uInitrd ...
5257173 bytes read in 554 ms (9 MiB/s)

As far as it's UBS 2 drive, speed is too low. Any ideas how to use USB 3 drive properly?

Waiting for /dev to be fully populated...[   17.860812][ T1546] mtdblock: MTD device 'ubifs' is NAND, please consider using UBI block devices instead.

Is it critical?

Nikola204,

> Sooooo....I made it! Now I'm looking at the
> Debian's console, but the problem was in USB
> Drive! I changed USB 3 to USB 2 drive and did the
> same steps according to the manual. And now
> everything works!

You must have some misstep somewhere. If I had set the env to use USB 3.0 then it did work for me.

How did you create the partiton on the USB 3.0 drive, using GUI or parted or fdisk? What type of filesystem?

Attach the USB 3.0 rootfs to another Linux box and at command line, do

dmesg | tail   # see the drive letter assigned by Linux

Assuming the drive was assigned /dev/sdb

mount | grep sdb
fdisk -l /dev/sdb

Also with this stock u-boot, always attach the USB rootfs to the port right next to the Ethernet port. I believe it is port 0.

Use this command to list the boot folder in u-boot:

ext2ls usb 0:1 /boot

Please post the log of the above here.


> For now I'm getting such log. Is everything fine
> there?
>

Everything else looks good except there is no network.

> No DHCPOFFERS received.
> No working leases in persistent database -
> sleeping.

Is the Ethernet cable connected?

> I'd like to understand, how to fix these error.
> Could somebody please help me?
>

> device usb 0:1
> ** File not found /boot/zImage **
>

> There is only zImage.fdt in /boot folder.

Ignore this error. That was the old style of booting in previous kernel for this box a long time ago.

> As far as it's UBS 2 drive, speed is too low. Any
> ideas how to use USB 3 drive properly?

See my suggestion above.

> 17.860812][ T1546] mtdblock: MTD device 'ubifs' is
> NAND, please consider using UBI block devices
> instead.
> [/code]
> Is it critical?

No. It's just a recommendation by the kernel, and it's not relevant to booting with USB or SDD/HDD.

======

Now that you are booting Debian. You can consider testing the new u-boot here:

https://forum.doozan.com/read.php?3,133945

The u-boot version for this Thecus N2350 is 2023.04. Recently I've finished the 2025.10 u-boot version, but have not got time to release it. It's not urgent to use the new u-boot, so you can wait until I release the 2025.10 version.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

bodhi Wrote:
-------------------------------------------------------
> You must have some misstep somewhere. If I had set
> the env to use USB 3.0 then it did work for me.
>
> How did you create the partiton on the USB 3.0
> drive, using GUI or parted or fdisk? What type of
> filesystem?

I tried everything - filesystems from ext2 till ext4, and volume size from 32Gb till 4Gb. But it didn't help.

fdisk /dev/sdd
n
p
1
Enter
Enter
w


mkfs.ext3 -L "rootfs" /dev/sdd1
e2label /dev/sdd1 rootfs

> Attach the USB 3.0 rootfs to another Linux box and
> at command line, do
>
>

> dmesg | tail   # see the drive letter assigned by
> Linux
>

> Assuming the drive was assigned /dev/sdb
>

> mount | grep sdb
> fdisk -l /dev/sdb
>

Here we go

blkid | grep sdd
/dev/sdd1: LABEL="rootfs" UUID="7250a8cf-4a32-43c9-af03-fe8b062c6b34" BLOCK_SIZE="4096" TYPE="ext2"



fdisk -l /dev/sdd

Disk /dev/sdd: 29.47 GiB, 31641829376 bytes, 61800448 sectors
Disk model: Silicon-Power32G
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x00000000

Device     Boot  Start      End  Sectors  Size Id Type
/dev/sdd1         2048 16779263 16777216    8G 83 Linux

mount | grep sdd

> Also with this stock u-boot, always attach the USB
> rootfs to the port right next to the Ethernet
> port. I believe it is port 0.

I used only this USB port.

> Use this command to list the boot folder in
> u-boot:
>

> ext2ls usb 0:1 /boot
>

>
> Please post the log of the above here.
>
>
Now I disconnected and assembled NAS so there is no UART console.
But I can assure you, that USB2 drive returned folder list after the "ext2ls usb 0" command. At the same time USB3 drive
returned one of these 2 errors:

** Bad device size - usb 0 **

** No partition table - usb 0 **

> Everything else looks good except there is no
> network.
> Is the Ethernet cable connected?
>
No, I attached it later.


> Now that you are booting Debian. You can consider
> testing the new u-boot here:
>
> https://forum.doozan.com/read.php?3,133945
>
> The u-boot version for this Thecus N2350 is
> 2023.04. Recently I've finished the 2025.10 u-boot
> version, but have not got time to release it. It's
> not urgent to use the new u-boot, so you can wait
> until I release the 2025.10 version.
I'd like to setup some services and to take a look how it goes. And then, when everything will be ok, to update OS and upgrade HDDs.
Many thanks for your help and your time.



So what are my next steps?
1) Find out why USB3 doesn't work?
2) Run from USB3
3) Update Kernel
4) Update U-boot?



Edited 1 time(s). Last edit at 12/24/2025 04:11PM by Nikola204.

> I tried everything - filesystems from ext2 till
> ext4, and volume size from 32Gb till 4Gb. But it
> didn't help.
>
> fdisk /dev/sdd
> n
> p
> 1
> Enter
> Enter
> w

We usually do the "O" command to wipe the disk partition(s) first. And this wipe resets the partition table.

fdisk /dev/sdd

o
n
p
1
Enter
Enter
w

> Now I disconnected and assembled NAS so there is no UART console.

> So what are my next steps?
> 1) Find out why USB3 doesn't work?

You will need serial console to figure out this problem. Try using a different USB 3.0 thumb drive, preferably Sandisk brand.

> 2) Run from USB3
> 3) Update Kernel

I would run with USB 2.0 rootfs for now, if trying a different brand of USB 3.0 does not work. Ideally, you would create a swap file on one of the HDD parition. See the Wiki thread

Quote
https://forum.doozan.com/read.php?2,23630

Memory & Swap Settings

Tuning for low RAM boxes - System and HDD performance. Also read several posts after for setups for logging to RAM.
logrotate examples
How to create and use a Swap file

The rootfs does not need speed, it would be slow only when you upgrade kernel and Debian. As long as the swap file is on HDD, it would run fine in all scenarios (except with OMV).

> 4) Update U-boot?

I'm not sure when I can release the new u-boot and write the installation steps. Perhaps a couple months from now.

In the mean time, you can also run kwboot to load the new u-boot image over UART. This is the unbrick procedure when things went badly with u-boot. But it is good to boot Debian on USB 3.0 drive if you have permanent serial console.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Quote

"We usually do the \"O\" command to wipe the disk partition(s) first. And this wipe resets the partition table.

Yep! It helped! Now I'm running from USB3.0 drive.

Quote

Ideally, you would create a swap file on one of the HDD parition.

Already done.
Also updated to the last kernel.


1) What do you think about zram? Should I configure it for N2350 ?
2) Is it possible to enable LAN LEDs ? LAN LEDs don't work on the front panel and on LAN port also. I configured other leds, but can't find out how to enable LAN LED.
3) Is it possible to use speaker? I'd like to to use it for power off and reboot notifications.
4) I searched through "how to save my USB" topic. What also should I do to extend my USB drive life?

- Use good (SanDisk) drive.
- Leave 50% space unformatted (over-provisioning, but from what I know, it works with f2fs or with ssd)
- use F2FS for / and Ext2 for /boot (could you please provide step by step manual, how to configure that?)
- move /var/log folder to hdd (how cat I make it?)

Could youp lease explain 2 last points?

5) I'd like to write logs to my HDD. How can I move /var/log folder there and enable logging?

6) I wanted to install Cockpit web interface. But it want to delete some applications. Is it critical for my Debian?

apt install -t ${VERSION_CODENAME}-backports cockpit cockpit-storaged
Reading package lists... Done
Building dependency tree... Done
Reading state information... Done
The following packages were automatically installed and are no longer required:
  libbpf0 libcbor0 libdns-export1110 libevent-2.1-7 libffi7 libicu67 libisc-export1105 libncurses6 libopts25 libperl5.32 libprocps8 libssl1.1 perl-modules-5.32
Use 'apt autoremove' to remove them.
The following additional packages will be installed:
  cockpit-bridge cockpit-system cockpit-ws dbus-user-session dconf-gsettings-backend dconf-service gdisk glib-networking glib-networking-common glib-networking-services gsettings-desktop-schemas
  libatasmart4 libblockdev-fs2 libblockdev-loop2 libblockdev-mdraid2 libblockdev-part-err2 libblockdev-part2 libblockdev-swap2 libblockdev-utils2 libblockdev2 libbytesize-common libbytesize1 libcrack2
  libdconf1 libgudev-1.0-0 libjson-glib-1.0-0 libjson-glib-1.0-common libmpfr6 libnss-systemd libpam-systemd libparted-fs-resize0 libparted2 libpolkit-agent-1-0 libpolkit-gobject-1-0 libproxy1v5
  libpwquality-common libpwquality-tools libpwquality1 libsystemd-shared libsystemd0 libudev1 libudisks2-0 mdadm parted python3-dbus systemd systemd-dev systemd-sysv udev udisks2
Suggested packages:
  cockpit-doc cockpit-sosreport xdg-utils python3-pcp udisks2-btrfs udisks2-lvm2 lastlog2 sssd-dbus libparted-dev libparted-i18n dracut-core parted-doc python-dbus-doc systemd-container systemd-homed
  systemd-userdbd systemd-boot systemd-resolved libqrencode4 libtss2-esys-3.0.2-0 libtss2-mu0 libtss2-rc0 polkitd python3-pefile btrfs-progs f2fs-tools nilfs-tools reiserfsprogs udftools
  udisks2-bcache udisks2-zram xfsprogs
Recommended packages:
  cockpit-networkmanager cockpit-packagekit cracklib-runtime default-mta | mail-transport-agent python3-gi dosfstools eject libblockdev-crypto2 ntfs-3g polkitd exfatprogs
The following packages will be REMOVED:
  initscripts orphan-sysvinit-scripts sysvinit-core
The following NEW packages will be installed:
  cockpit cockpit-bridge cockpit-storaged cockpit-system cockpit-ws dbus-user-session dconf-gsettings-backend dconf-service gdisk glib-networking glib-networking-common glib-networking-services
  gsettings-desktop-schemas libatasmart4 libblockdev-fs2 libblockdev-loop2 libblockdev-mdraid2 libblockdev-part-err2 libblockdev-part2 libblockdev-swap2 libblockdev-utils2 libblockdev2
  libbytesize-common libbytesize1 libcrack2 libdconf1 libgudev-1.0-0 libjson-glib-1.0-0 libjson-glib-1.0-common libmpfr6 libnss-systemd libpam-systemd libparted-fs-resize0 libparted2
  libpolkit-agent-1-0 libpolkit-gobject-1-0 libproxy1v5 libpwquality-common libpwquality-tools libpwquality1 libudisks2-0 mdadm parted python3-dbus systemd-dev systemd-sysv udisks2
The following packages will be upgraded:
  libsystemd-shared libsystemd0 libudev1 systemd udev
5 upgraded, 47 newly installed, 3 to remove and 24 not upgraded.
Need to get 16.8 MB of archives.
After this operation, 24.7 MB of additional disk space will be used.

The following packages will be REMOVED:
  initscripts orphan-sysvinit-scripts sysvinit-core

Thanks in advance!

> 1) What do you think about zram? Should I
> configure it for N2350 ?

It 's really depending on what you'll use the box for.

> 2) Is it possible to enable LAN LEDs ? LAN LEDs
> don't work on the front panel and on LAN port
> also. I configured other leds, but can't find out
> how to enable LAN LED.

I've not paid any attention to LAN LEDs (not important, but nice to have). I'll take a look for the next kernel. This is something common for various Marvell Ethernet drivers.


> 3) Is it possible to use speaker? I'd like to to
> use it for power off and reboot notifications.

The buzzer does not work when I tried long ago. That'll go into the wish list.

> 4) I searched through "how to save my USB" topic.
> What also should I do to extend my USB drive
> life?

See Wiki topics

Quote
https://forum.doozan.com/read.php?2,23630
Flash drives issues

How to prolong the life of your rootfs USB thumb drive
Overprovisioning A Flash Drive?

> - Leave 50% space unformatted (over-provisioning,
> but from what I know, it works with f2fs or with
> ssd)

That's too much. I use 10-20%. If you fill up that overprovisioning then your USB drive is dying, and need to be replaced.

> - move /var/log folder to hdd (how cat I make
> it?)

> Could youp lease explain 2 last points?
>
> 5) I'd like to write logs to my HDD. How can I
> move /var/log folder there and enable logging?

Search for

mount -o bind

and turn off logging to RAM by reconfiguring to remove the option in conf file for busybox-syslogd.

> 6) I wanted to install Cockpit web interface. But
> it want to delete some applications. Is it
> critical for my Debian?

>

> The following packages will be REMOVED:
>   initscripts orphan-sysvinit-scripts
> sysvinit-core
>

That because cockpit is only support with systemd. So if you want to run cockpit, it will remove the sysvinit scripts and a packages.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)



Edited 1 time(s). Last edit at 12/25/2025 04:28PM by bodhi.

bodhi Wrote:
-------------------------------------------------------
> > 1) What do you think about zram? Should I
> > configure it for N2350 ?
>
> It 's really depending on what you'll use the box
> for.
>

Small Docker containers, network shares, services (Syncthing, nginx, iperf3).

> > 6) I wanted to install Cockpit web interface.
> But
> > it want to delete some applications. Is it
> > critical for my Debian?
>
> >

> > The following packages will be REMOVED:
> >   initscripts orphan-sysvinit-scripts
> > sysvinit-core
> >

>
> That because cockpit is only support with systemd.
> So if you want to run cockpit, it will remove the
> sysvinit scripts and a packages.


I installed systemd earlier. And the question is does this installation process (with sysv init remove step) is safe for my system? I'm not so qualified, so could you help me with that question?


Regards,
Nikola204



Edited 1 time(s). Last edit at 12/30/2025 03:59AM by Nikola204.

> I installed systemd earlier. And th question is
> does this installation process (with sysv init
> remove step) save for my system? I'm not so
> qualified, so could you help me with that
> question?

I'm not using systemd for any of these small embedded devices, and therefore not using cockpit. So I'm not the best person to answer this question.

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)

Hi all,
can anyone tell me, what is the maximum disk size for Thecus N2350? Can I install 12Tb drives?
And one more thing. Does anyone use Docker on N2350? Is yes, can you please test, is it possible to run Docker containers with CPU limitations? I'm asking because I can limit only memory for specified container.


Thanks in advance.
Regards,
Nikola204



Edited 1 time(s). Last edit at 01/08/2026 05:01AM by Nikola204.