|
Can't boot from USB-Stick July 10, 2011 01:23PM |
Registered: 12 years ago Posts: 3 |
U-Boot 2010.09 (Oct 23 2010 - 11:49:22)
Marvell-Dockstar/Pogoplug by Jeff Doozan
SoC: Kirkwood 88F6281_A0
DRAM: 128 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... error in inquiry
0 Storage Device(s) found
** Block device usb 0 not supported
** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI error: ubi_read_volume_table: the layout volume was not found
UBI error: ubi_init: cannot attach mtd1
UBI error: ubi_init: UBI error: cannot initialize UBI, error -22
UBI init error -22
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: .......... done.
### JFFS2 load complete: 524288 bytes loaded to 0x800000
## Starting application at 0x00800200 ...
U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16)
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60
Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: REDSTONE:0.1
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x100000, size 0x300000
Reading data from 0x3ff800 -- 100% complete.
3145728 bytes read: OK
## Booting image at 00800000 ...
Image Name: Linux-2.6.22.18
Created: 2009-08-31 23:31:05 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1976384 Bytes = 1.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux............................................................................................................................ done, booti.
[ 0.000000] Linux version 2.6.22.18 (bdietrich@brad-ux) (gcc version 4.2.1) #57 Mon Aug 31 16:31:01 PDT 2009
[ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177
[ 0.000000] Machine: Feroceon-KW
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU0: D VIVT write-back cache
[ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] Built 1 zonelists. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 128MB 0MB 0MB 0MB = 128MB total
[ 0.000000] Memory: 125824KB available (3588K code, 252K data, 120K init)
[ 0.240000] Mount-cache hash table entries: 512
[ 0.240000] CPU: Testing write buffer coherency: ok
[ 0.240000] NET: Registered protocol family 16
[ 0.240000]
[ 0.240000] CPU Interface
[ 0.240000] -------------
[ 0.240000] SDRAM_CS0 ....base 00000000, size 128MB
[ 0.240000] SDRAM_CS1 ....disable
[ 0.240000] SDRAM_CS2 ....disable
[ 0.240000] SDRAM_CS3 ....disable
[ 0.240000] PEX0_MEM ....base e8000000, size 128MB
[ 0.240000] PEX0_IO ....base f2000000, size 1MB
[ 0.240000] INTER_REGS ....base f1000000, size 1MB
[ 0.240000] NFLASH_CS ....base fa000000, size 2MB
[ 0.240000] SPI_CS ....base f4000000, size 16MB
[ 0.240000] BOOT_ROM_CS ....no such
[ 0.240000] DEV_BOOTCS ....no such
[ 0.240000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.240000]
[ 0.240000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG Soc: 88F6281 A0 LE
[ 0.240000]
[ 0.240000] Detected Tclk 200000000 and SysClk 400000000
[ 0.240000] MV Buttons Device Load
[ 0.240000] Marvell USB EHCI Host controller #0: c0537600
[ 0.740000] PEX0 interface detected no Link.
[ 0.740000] PCI: bus0: Fast back to back transfers enabled
[ 0.740000] SCSI subsystem initialized
[ 0.740000] usbcore: registered new interface driver usbfs
[ 0.740000] usbcore: registered new interface driver hub
[ 0.740000] usbcore: registered new device driver usb
[ 0.740000] NET: Registered protocol family 2
[ 0.750000] Time: kw_clocksource clocksource has been installed.
[ 0.840000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.840000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.840000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.840000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.840000] TCP reno registered
[ 0.870000] RTC has been updated!!!
[ 0.870000] RTC registered
[ 0.870000] Use the XOR engines (acceleration) for enhancing the following functions:
[ 0.870000] o RAID 5 Xor calculation
[ 0.870000] o kernel memcpy
[ 0.870000] o kenrel memzero
[ 0.870000] Number of XOR engines to use: 4
[ 0.870000] cesadev_init(c00116b4)
[ 0.870000] mvCesaInit: sessions=640, queue=64, pSram=f0000000
[ 0.870000] MV Buttons Driver Load
[ 0.870000] squashfs: version 3.3 (2007/10/31) Phillip Lougher
[ 0.870000] squashfs: LZMA suppport for slax.org by jro
[ 0.870000] JFFS2 version 2.2. (NAND) �Â�© 2001-2006 Red Hat, Inc.
[ 0.870000] io scheduler noop registered
[ 0.870000] io scheduler anticipatory registered (default)
[ 0.890000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
[ 0.890000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 0.900000] serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[ 0.900000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
[ 0.910000] Loading Marvell Ethernet Driver:
[ 0.920000] o Cached descriptors in DRAM
[ 0.920000] o DRAM SW cache-coherency
[ 0.920000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 0.930000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 0.940000] o TCP segmentation offload enabled
[ 0.940000] o Receive checksum offload enabled
[ 0.940000] o Transmit checksum offload enabled
[ 0.950000] o Network Fast Processing (Routing) supported
[ 0.960000] o Driver ERROR statistics enabled
[ 0.960000] o Driver INFO statistics enabled
[ 0.960000] o Proc tool API enabled
[ 0.970000] o Rx descripors: q0=128
[ 0.970000] o Tx descripors: q0=532
[ 0.980000] o Loading network interface(s):
[ 0.980000] o eth0, ifindex = 1, GbE port = 0
[ 0.990000] o eth1, ifindex = 2, GbE port = 1
[ 0.990000]
[ 1.000000] mvFpRuleDb (c7ed5000): 1024 entries, 4096 bytes
[ 1.000000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[ 1.010000] Copyright (c) 1999-2006 Intel Corporation.
[ 1.010000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
[ 1.020000] e100: Copyright(c) 1999-2006 Intel Corporation
[ 1.020000]
[ 1.020000] Warning Sata is Powered Off
[ 1.030000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
[ 1.040000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)
[ 1.050000] Scanning device for bad blocks
[ 1.130000] Bad eraseblock 1549 at 0x0c1a0000
[ 1.150000] Using static partition definition
[ 1.160000] Creating 4 MTD partitions on "nand_mtd":
[ 1.160000] 0x00000000-0x00100000 : "u-boot"
[ 1.170000] 0x00100000-0x00500000 : "uImage"
[ 1.170000] 0x00500000-0x02500000 : "root"
[ 1.180000] 0x02500000-0x10000000 : "data"
[ 1.180000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
[ 1.190000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
[ 1.230000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
[ 1.250000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 1.250000] usb usb1: configuration #1 chosen from 1 choice
[ 1.260000] hub 1-0:1.0: USB hub found
[ 1.260000] hub 1-0:1.0: 1 port detected
[ 1.380000] USB Universal Host Controller Interface driver v3.0
[ 1.660000] usb 1-1: new high speed USB device using ehci_marvell and address 2
[ 1.810000] usb 1-1: configuration #1 chosen from 1 choice
[ 1.810000] hub 1-1:1.0: USB hub found
[ 1.820000] hub 1-1:1.0: 4 ports detected
[ 2.170000] usb 1-1.2: new high speed USB device using ehci_marvell and address 3
[ 2.380000] usb 1-1.2: configuration #1 chosen from 1 choice
[ 2.390000] usbcore: registered new interface driver usblp
[ 2.390000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[ 2.400000] Initializing USB Mass Storage driver...
[ 2.400000] scsi0 : SCSI emulation for USB Mass Storage devices
[ 2.410000] usbcore: registered new interface driver usb-storage
[ 2.420000] USB Mass Storage support registered.
[ 2.420000] mice: PS/2 mouse device common for all mice
[ 2.430000] i2c /dev entries driver
[ 2.430000] Linux telephony interface: v1.00
[ 2.430000] md: linear personality registered for level -1
[ 2.440000] md: raid0 personality registered for level 0
[ 2.440000] md: raid1 personality registered for level 1
[ 2.620000] raid6: int32x1 97 MB/s
[ 2.790000] raid6: int32x2 114 MB/s
[ 2.960000] raid6: int32x4 122 MB/s
[ 3.130000] raid6: int32x8 110 MB/s
[ 3.130000] raid6: using algorithm int32x4 (122 MB/s)
[ 3.130000] md: raid6 personality registered for level 6
[ 3.140000] md: raid5 personality registered for level 5
[ 3.140000] md: raid4 personality registered for level 4
[ 3.150000] raid5: measuring checksumming speed
[ 3.200000] arm4regs : 1084.000 MB/sec
[ 3.250000] 8regs : 754.800 MB/sec
[ 3.300000] 32regs : 890.400 MB/sec
[ 3.300000] raid5: using function: arm4regs (1084.000 MB/sec)
[ 3.310000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
[ 3.310000] dm_crypt using the OCF package.
[ 3.320000] sdhci: Secure Digital Host Controller Interface driver
[ 3.320000] sdhci: Copyright(c) Pierre Ossman
[ 3.330000] usbcore: registered new interface driver usbhid
[ 3.330000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 3.340000] TCP cubic registered
[ 3.340000] NET: Registered protocol family 1
[ 3.350000] NET: Registered protocol family 17
[ 3.350000] md: Autodetecting RAID arrays.
[ 3.360000] md: autorun ...
[ 3.360000] md: ... autorun DONE.
[ 5.560000] Empty flash at 0x00de8e44 ends at 0x00de9000
[ 5.640000] Empty flash at 0x00f0e3c0 ends at 0x00f0e800
[ 10.050000] VFS: Mounted root (jffs2 filesystem) readonly.
[ 10.050000] Freeing init memory: 120K
[ 11.280000] scsi 0:0:0:0: Direct-Access Verbatim STORE N GO 1100 PQ: 0 ANSI: 0 CCS
[ 11.470000] sd 0:0:0:0: [sda] 31506432 512-byte hardware sectors (16131 MB)
[ 11.550000] sd 0:0:0:0: [sda] Write Protect is off
[ 11.550000] sd 0:0:0:0: [sda] Assuming drive cache: write through
init started: BusyBox v1.7.0 (2008-02-26 19:25:[ 11.650000] sd 0:0:0:0: [sda] 31506432 512-byte hardware sectors (16131 MB)
17 IST)
starting pid 281, tty '': '/etc[ 11.660000] sd 0:0:0:0: [sda] Write Protect is off
/init.d/rcS'
[ 11.660000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 11.670000] sda: sda1 sda2
[ 11.680000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 11.680000] sd 0:0:0:0: Attached scsi generic sg0 type 0
udhcpc (v1.7.0) started
HWADDR 00 0x50 0x43 0x00 0x02 0x02
PIP0 2
PIP1 2
[ 12.500000] eth0: link down
[ 12.500000] eth0: started
Sending discover...
Sending discover...
[ 16.210000] eth0: link up, full duplex, speed 1 Gbps
Sending discover...
Sending select for 192.168.2.26...
Lease of 192.168.2.26 obtained, lease time 864000
HWADDR 00 0x50 0x43 0x00 0x02 0x02
PIP0 2
PIP1 2
eth0 Link encap:Ethernet HWaddr 00:50:43:00:02:02
inet addr:192.168.2.26 Bcast:192.168.2.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3 errors:0 dropped:0 overruns:0 frame:0
TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:532
RX bytes:1240 (1.2 KiB) TX bytes:1180 (1.1 KiB)
Interrupt:11
eth0:0 Link encap:Ethernet HWaddr 00:50:43:00:02:02
inet addr:169.254.2.2 Bcast:169.254.255.255 Mask:255.255.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Interrupt:11
starting pid 337, tty '': '/bin/sh'
-sh-3.2#
-sh-3.2# ls bin mnt tmp dev proc uboot-original-mtd0.kwb etc root usr lib sbin var linuxrc sys -sh-3.2# cd /tmp -sh-3.2# ls resolv.conf var -sh-3.2# wget http://jeff.doozan.com/debian/uboot/install_uboot_mtd0.sh Connecting to jeff.doozan.com (69.163.187.226:80) install_uboot_mtd0.s 100% |*******************************| 17281 --:--:-- ETA -sh-3.2# ls install_uboot_mtd0.sh resolv.conf var -sh-3.2# chmod +x install_uboot_mtd0.sh -sh-3.2# ./install_uboot_mtd0.sh !!!!!! DANGER DANGER DANGER DANGER DANGER DANGER !!!!!! If you lose power to your device while running this script, it could be left in an unusable state. This script will replace the bootloader on /dev/mtd0. This installer will only work on the following devices: Seagate GoFlex Net Seagate Dockstar Pogoplug v1 Pogoplug Pink Do not run this installer on any other device. By typing ok, you agree to assume all liabilities and risks associated with running this installer. If you agree, type 'ok' and press ENTER to continue: ok # checking for /usr/sbin/nandwrite... # checking for /usr/sbin/nanddump... # checking for /usr/sbin/flash_erase... # checking for /usr/sbin/fw_printenv... # checking for /etc/fw_env.config... # Validating existing uBoot... Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x00000000 and ending at 0x00080000... Connecting to jeff.doozan.com (69.163.187.226:80) valid-uboot.md5 100% |*******************************| 756 --:--:-- ETA ## Valid uBoot detected: [dockstar jeff-2010-10-23-current ebd566de30c6521e65fb1255415c037f pogov1 jeff-2010-10-23-current] ## The newest uBoot is already installed on mtd0. You are already running the latest uBoot. Would you like to reset the uBoot environment? [N/y] y # Installing uBoot environment Connecting to jeff.doozan.com (69.163.187.226:80) uboot.environment.md 100% |*******************************| 52 --:--:-- ETA Connecting to jeff.doozan.com (69.163.187.226:80) uboot.environment 100% |*******************************| 128k --:--:-- ETA Erase Total 1 Units Performing Flash Erase of length 131072 at offset 0xc0000 done Writing data to block 6 at offset 0xc0000 # Verifying uBoot environment Block size 131072, page size 2048, OOB size 64 Dumping data starting at 0x000c0000 and ending at 0x000e0000... Connecting to jeff.doozan.com (69.163.187.226:80) uboot.environment.md 100% |*******************************| 52 --:--:-- ETA # uBoot installation has completed successfully. -sh-3.2# -sh-3.2# fw_printenv ethact=egiga0 bootdelay=3 baudrate=115200 mainlineLinux=yes console=ttyS0,115200 led_init=green blinking led_exit=green off led_error=orange blinking mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) mtdids=nand0=orion_nand partition=nand0,2 stdin=serial stdout=serial stderr=serial rescue_installed=0 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmdi pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_boi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bi usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; thene usb_scan_list=1 2 3 4 usb_scan_1=usb=0:1 dev=sda1 usb_scan_2=usb=1:1 dev=sdb1 usb_scan_3=usb=2:1 dev=sdc1 usb_scan_4=usb=3:1 dev=sdd1 usb_init=run usb_scan usb_device=0:1 usb_root=/dev/sda1 usb_rootfstype=ext2 usb_rootdelay=10 usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x110000i bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset ethaddr=00:50:43:00:02:02 arcNumber=2998 -sh-3.2#
|
Re: Can't boot from USB-Stick July 10, 2011 06:48PM |
Registered: 13 years ago Posts: 161 |
Quote
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... error in inquiry
0 Storage Device(s) found
** Block device usb 0 not supported
|
Re: Can't boot from USB-Stick July 11, 2011 03:48AM |
Registered: 12 years ago Posts: 3 |
...
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
...
|
postma
Re: Can't boot from USB-Stick November 07, 2011 08:07AM |