After installation of the latest UBoot, it stuck at "Starting kernel ..." March 15, 2018 03:24AM |
Registered: 11 years ago Posts: 4 |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700) Pogo E02 gcc (Debian 6.3.0-18) 6.3.0 20170516 GNU ld (GNU Binutils for Debian) 2.28 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Unknown command 'ide' - try 'help' Unknown command 'mmc' - try 'help' Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 7825408 8b357a98-01 83 Boot ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... 87 bytes read in 754 ms (0 Bytes/s) Unknown command 'ide' - try 'help' Unknown command 'mmc' - try 'help' importing envs ... running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 692 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 3926040 bytes read in 1001 ms (3.7 MiB/s) loading uInitrd ... 8104328 bytes read in 1109 ms (7 MiB/s) loading DTB /boot/dts/kirkwood-pogo_e02.dtb ... 10444 bytes read in 3583 ms (2 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.15.2-kirkwood-tld-1 Created: 2018-03-14 5:36:31 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3925976 Bytes = 3.7 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.15.2-kirkwood-tld-1 Created: 2018-03-14 8:56:52 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 8104264 Bytes = 7.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Starting kernel ...
PogoE02> printenv arcNumber=3542 bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb device=0:1 devices=usb ide mmc disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-pogo_e02.dtb ethact=egiga0 ethaddr=52:3b:20:9c:11:51 if_netconsole=ping $serverip ipaddr=192.168.2.19 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x1c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 machid=dd6 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) nc_ready=1 ncip=192.168.2.118 partition=nand0,2 preboot=run preboot_nc preboot_nc=setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.2.118 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=nc stdin=nc stdout=nc uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi usb_ready_retry=15 Environment size: 3039/131068 bytes
Re: After installation of the latest UBoot, it stuck at "Starting kernel ..." March 15, 2018 03:03PM |
Admin Registered: 13 years ago Posts: 18,569 |
setenv custom_params 'earlyprintk=serial' printenv bootPlease post the entire serial console here.
Re: After installation of the latest UBoot, it stuck at "Starting kernel ..." March 16, 2018 11:25AM |
Registered: 11 years ago Posts: 4 |
Re: After installation of the latest UBoot, it stuck at "Starting kernel ..." March 16, 2018 03:40PM |
Admin Registered: 13 years ago Posts: 18,569 |