Geah Heh
Problem booting NSA320 with Linux Kernel 4.12.1-kirkwood-tld-1 April 13, 2018 09:38PM |
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:46:11 -0700) ZyXEL NSA320 2-Bay Power Media Server SoC: Kirkwood 88F6281_A1 DRAM: 512 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... Use USB retry period from the environment: 15 second(s) 1 Storage Device(s) found Reset IDE: Bus 0: OK Bus 1: OK Device 0: Model: WDC WD30EZRX-00MMMB0 Firm: 80.00A80 Ser#: WD-WCAWZ2135552 Type: Hard Disk Supports 48-bit addressing Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512) Device 1: Model: WDC WD30EZRX-00DC0B0 Firm: 80.00A80 Ser#: WD-WCC1T0083436 Type: Hard Disk Supports 48-bit addressing Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512) Unknown command 'mmc' - try 'help' Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 231997953 85897bcc-01 83 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** Partition Map for IDE device 0 -- Partition Type: EFI Part Start LBA End LBA Name Attributes Type GUID Partition GUID 1 0x00000800 0x000f3fff "firmware" attrs: 0x0000000000000000 type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7 type: data guid: 0c38e79c-ef49-4266-a7a4-4da12d6f7814 2 0x000f4000 0x15d509fff "eexxtt44" attrs: 0x0000000000000000 type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7 type: data guid: 15d4fedb-052b-4192-9dd5-15e64500ee68 Partition Map for IDE device 1 -- Partition Type: EFI Part Start LBA End LBA Name Attributes Type GUID Partition GUID 1 0x00000800 0x000f3fff "mitraswap" attrs: 0x0000000000000000 type: 0657fd6d-a4ab-43c4-84e5-0933c84b4f4f type: swap guid: 5b1bc3dd-da12-4654-b7e3-9dabbd5c7337 2 0x000f4000 0x15d509fff "eexxtt44" attrs: 0x0000000000000000 type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7 type: data guid: b90af540-140e-4324-b27c-52b1fd15cff4 Unknown command 'mmc' - try 'help' running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 692 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 3821592 bytes read in 809 ms (4.5 MiB/s) loading uInitrd ... 7245696 bytes read in 779 ms (8.9 MiB/s) loading DTB /boot/dts/kirkwood-nsa320.dtb ... 13691 bytes read in 2675 ms (4.9 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-4.12.1-kirkwood-tld-1 Created: 2017-07-20 8:11:24 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3821528 Bytes = 3.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-4.12.1-kirkwood-tld-1 Created: 2017-07-24 0:18:23 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7245632 Bytes = 6.9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01c00000 Booting using the fdt blob at 0x1c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f917000, end 0fffff40 ... OK Loading Device Tree to 0f910000, end 0f91657a ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.1-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sat Jul 15 21:40:50 PDT 2017 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: Zyxel NSA320 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 499256K/524288K available (8192K kernel code, 716K rwdata, 1972K rodata, 1024K init, 288K bss, 25032K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db3274 ( 717 kB) [ 0.000000] .bss : 0xc0db9b9c - 0xc0e01e60 ( 289 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000042] Switching to timer-based delay loop, resolution 5ns [ 0.000512] Console: colour dummy device 80x30 [ 0.000546] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000569] pid_max: default: 32768 minimum: 301 [ 0.000768] Security Framework initialized [ 0.000892] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000911] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001759] CPU: Testing write buffer coherency: ok [ 0.002747] Setting up static identity map for 0x100000 - 0x100058 [ 0.003039] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.006304] devtmpfs: initialized [ 0.011451] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.011478] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.011859] prandom: seed boundary self test passed [ 0.015595] prandom: 100 self tests passed [ 0.015606] pinctrl core: initialized pinctrl subsystem [ 0.016763] NET: Registered protocol family 16 [ 0.017309] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.018913] cpuidle: using governor ladder [ 0.018984] cpuidle: using governor menu [ 0.019513] Feroceon L2: Enabling L2 [ 0.019559] Feroceon L2: Cache support initialised. [ 0.019951] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.025545] No ATAGs? [ 0.035179] vgaarb: loaded [ 0.035501] SCSI subsystem initialized [ 0.035978] usbcore: registered new interface driver usbfs [ 0.036056] usbcore: registered new interface driver hub [ 0.036148] usbcore: registered new device driver usb [ 0.037219] clocksource: Switched to clocksource orion_clocksource [ 0.125966] VFS: Disk quotas dquot_6.6.0 [ 0.126047] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.136699] NET: Registered protocol family 2 [ 0.137472] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.137533] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.137586] TCP: Hash tables configured (established 4096 bind 4096) [ 0.137672] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.137697] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.137872] NET: Registered protocol family 1 [ 0.138277] RPC: Registered named UNIX socket transport module. [ 0.138289] RPC: Registered udp transport module. [ 0.138296] RPC: Registered tcp transport module. [ 0.138303] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.138536] Unpacking initramfs... [ 0.793049] Freeing initrd memory: 7076K [ 0.793264] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.794091] audit: initializing netlink subsys (disabled) [ 0.794528] Initialise system trusted keyrings [ 0.794589] Key type blacklist registered [ 0.794681] audit: type=2000 audit(0.787:1): state=initialized audit_enabled=0 res=1 [ 0.794778] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.794848] zbud: loaded [ 0.795808] NFS: Registering the id_resolver key type [ 0.795838] Key type id_resolver registered [ 0.795846] Key type id_legacy registered [ 0.795871] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.795882] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.796078] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.796274] fuse init (API version 7.26) [ 0.796610] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.796824] orangefs_init: module version upstream loaded [ 0.796836] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 2.557230] random: fast init done [ 6.642366] Key type asymmetric registered [ 6.642383] Asymmetric key parser 'x509' registered [ 6.642449] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 6.642460] io scheduler noop registered [ 6.642468] io scheduler deadline registered [ 6.642554] io scheduler cfq registered (default) [ 6.643812] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 6.645688] mvebu-pcie mbus@f1000000:pcie-controller@82000000: PCI host bridge to bus 0000:00 [ 6.645710] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 6.645723] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 6.645737] pci_bus 0000:00: root bus resource [bus 00-ff] [ 6.646073] PCI: bus0: Fast back to back transfers disabled [ 6.646098] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 6.646262] PCI: bus1: Fast back to back transfers enabled [ 6.646337] pci 0000:00:01.0: PCI bridge to [bus 01] [ 6.646905] mv_xor f1060800.xor: Marvell shared XOR driver [ 6.707953] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 6.708182] mv_xor f1060900.xor: Marvell shared XOR driver [ 6.767948] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr ) [ 6.768401] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 6.769734] console [ttyS0] disabled [ 6.769799] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 7.435698] console [ttyS0] enabled [ 7.447627] loop: module loaded [ 7.451357] sata_mv f1080000.sata: slots 32 ports 2 [ 7.459105] scsi host0: sata_mv [ 7.462709] scsi host1: sata_mv [ 7.466103] ata1: SATA max UDMA/133 irq 33 [ 7.470270] ata2: SATA max UDMA/133 irq 33 [ 7.475153] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1 [ 7.481636] nand: Samsung NAND 128MiB 3,3V 8-bit [ 7.486280] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 7.493912] Scanning device for bad blocks [ 7.596591] 9 ofpart partitions found on MTD device orion_nand [ 7.602469] Creating 9 MTD partitions on "orion_nand": [ 7.607662] 0x000000000000-0x000000100000 : "uboot" [ 7.613881] 0x000000100000-0x000000180000 : "uboot_env" [ 7.620511] 0x000000180000-0x000000200000 : "key_store" [ 7.627076] 0x000000200000-0x000000280000 : "info" [ 7.633031] 0x000000280000-0x000000c80000 : "etc" [ 7.638979] 0x000000c80000-0x000001680000 : "kernel_1" [ 7.645356] 0x000001680000-0x000004640000 : "rootfs1" [ 7.651998] 0x000004640000-0x000005040000 : "kernel_2" [ 7.658509] 0x000005040000-0x000008000000 : "rootfs2" [ 7.666378] libphy: Fixed MDIO Bus: probed [ 7.671394] libphy: orion_mdio_bus: probed [ 7.680487] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 7.787714] mv643xx_eth: Set the PHY to fix link down [ 7.788387] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address c8:6c:87:f8:3e:b9 [ 7.802382] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.809060] ehci-pci: EHCI PCI platform driver [ 7.813579] ehci-orion: EHCI orion driver [ 7.817843] orion-ehci f1050000.ehci: EHCI Host Controller [ 7.823385] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 7.831266] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 7.867252] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 7.873525] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 7.880375] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.887647] usb usb1: Product: EHCI Host Controller [ 7.892545] usb usb1: Manufacturer: Linux 4.12.1-kirkwood-tld-1 ehci_hcd [ 7.899295] usb usb1: SerialNumber: f1050000.ehci [ 7.904650] hub 1-0:1.0: USB hub found [ 7.908515] hub 1-0:1.0: 1 port detected [ 7.913074] usbcore: registered new interface driver usb-storage [ 7.919504] mousedev: PS/2 mouse device common for all mice [ 7.925670] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0 [ 7.932776] i2c /dev entries driver [ 7.942837] rtc-pcf8563 0-0051: rtc core: registered rtc-pcf8563 as rtc1 [ 7.952850] hidraw: raw HID events driver (C) Jiri Kosina [ 7.958694] drop_monitor: Initializing network drop monitor service [ 7.965218] NET: Registered protocol family 17 [ 7.969788] Key type dns_resolver registered [ 7.974932] registered taskstats version 1 [ 7.979110] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 7.985802] Loading compiled-in X.509 certificates [ 7.990823] zswap: loaded using pool lzo/zbud [ 8.005164] Key type big_key registered [ 8.017429] ata1.00: ATA-8: WDC WD30EZRX-00MMMB0, 80.00A80, max UDMA/133 [ 8.024167] ata1.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 8.032415] Key type encrypted registered [ 8.033744] rtc-mv f1010300.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 8.079581] ata1.00: configured for UDMA/133 [ 8.094460] scsi 0:0:0:0: Direct-Access ATA WDC WD30EZRX-00M 0A80 PQ: 0 ANSI: 5 [ 8.103812] sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB) [ 8.112126] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 8.117534] sd 0:0:0:0: [sda] Write Protect is off [ 8.122474] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.181286] sda: sda1 sda2 [ 8.185952] sd 0:0:0:0: [sda] Attached SCSI disk [ 8.277257] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 8.469027] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 8.475780] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 8.482983] usb 1-1: Product: USB2.0 Hub [ 8.487833] hub 1-1:1.0: USB hub found [ 8.491901] hub 1-1:1.0: 4 ports detected [ 8.617259] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 8.628122] ata2.00: ATA-9: WDC WD30EZRX-00DC0B0, 80.00A80, max UDMA/133 [ 8.634865] ata2.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 8.644257] ata2.00: configured for UDMA/133 [ 8.659131] scsi 1:0:0:0: Direct-Access ATA WDC WD30EZRX-00D 0A80 PQ: 0 ANSI: 5 [ 8.668391] sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB) [ 8.676171] sd 1:0:0:0: [sdb] 4096-byte physical blocks [ 8.681856] sd 1:0:0:0: [sdb] Write Protect is off [ 8.686796] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.817248] usb 1-1.2: new high-speed USB device number 3 using orion-ehci [ 9.048650] usb 1-1.2: New USB device found, idVendor=152d, idProduct=1561 [ 9.055573] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 9.062953] usb 1-1.2: Product: SABRENT [ 9.066806] usb 1-1.2: Manufacturer: SABRENT [ 9.071118] usb 1-1.2: SerialNumber: DB9876543214E [ 9.404043] sdb: sdb1 sdb2 [ 9.408639] sd 1:0:0:0: [sdb] Attached SCSI disk [ 9.416155] Freeing unused kernel memory: 1024K Loading, please wait... starting version 232 [ 9.967404] scsi host2: uas [ 9.971832] scsi 2:0:0:0: Direct-Access SABRENT 0204 PQ: 0 ANSI: 6 [ 9.985121] usbcore: registered new interface driver uas [ 10.050192] sd 2:0:0:0: [sdc] 234441648 512-byte logical blocks: (120 GB/112 GiB) [ 10.064357] sd 2:0:0:0: [sdc] 4096-byte physical blocks [ 10.075562] sd 2:0:0:0: [sdc] Write Protect is off [ 10.086060] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 10.617087] sdc: sdc1 [ 10.624792] sd 2:0:0:0: [sdc] Attached SCSI disk Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... done. IP-Config: eth0 hardware address c8:6c:87:f8:3e:b9 mtu 1500 DHCP RARP IP-Config: no response after 2 secs - giving up IP-Config: eth0 hardware address c8:6c:87:f8:3e:b9 mtu 1500 DHCP RARP IP-Config: no response after 3 secs - giving up IP-Config: eth0 hardware address c8:6c:87:f8:3e:b9 mtu 1500 DHCP RARP IP-Config: no response after 4 secs - giving up IP-Config: eth0 hardware address c8:6c:87:f8:3e:b9 mtu 1500 DHCP RARP IP-Config: no response after 6 secs - giving up IP-Config: eth0 hardware address c8:6c:87:f8:3e:b9 mtu 1500 DHCP RARP IP-Config: no response after 9 secs - giving up IP-Config: eth0 hardware address c8:6c:87:f8:3e:b9 mtu 1500 DHCP RARP IP-Config: no response after 16 secs - giving up IP-Config: eth0 hardware address c8:6c:87:f8:3e:b9 mtu 1500 DHCP RARP IP-Config: no response after 25 secs - giving up IP-Config: eth0 hardware address c8:6c:87:f8:3e:b9 mtu 1500 DHCP RARP IP-Config: no response after 36 secs - giving up IP-Config: eth0 hardware address c8:6c:87:f8:3e:b9 mtu 1500 DHCP RARP [ 20.948939] mv643xx_eth: Set the PHY back to auto-negotiation mode [ 128.022644] random: crng init done IP-Config: no response after 64 secs - giving up IP-Config: eth0 hardware address c8:6c:87:f8:3e:b9 mtu 1500 DHCP RARP IP-Config: no response after 100 secs - giving up /init: .: line 230: can't open '/run/net-*.conf' [ 285.847350] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000200 [ 285.847350] [ 285.856536] CPU: 0 PID: 1 Comm: init Not tainted 4.12.1-kirkwood-tld-1 #1 [ 285.863348] Hardware name: Marvell Kirkwood (Flattened Device Tree) [ 285.869676] [<c010ea54>] (unwind_backtrace) from [<c010ab48>] (show_stack+0x10/0x14) [ 285.877464] [<c010ab48>] (show_stack) from [<c01dba9c>] (panic+0xb0/0x250) [ 285.884378] [<c01dba9c>] (panic) from [<c011a3e8>] (do_exit+0x5e0/0xa64) [ 285.891113] [<c011a3e8>] (do_exit) from [<c011bc18>] (do_group_exit+0x4c/0xec) [ 285.898376] [<c011bc18>] (do_group_exit) from [<c011bcc8>] (__wake_up_parent+0x0/0x18) [ 285.906341] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000200 [ 285.906341]
Re: Problem booting NSA320 with Linux Kernel 4.12.1-kirkwood-tld-1 April 13, 2018 10:37PM |
Admin Registered: 13 years ago Posts: 18,560 |
[ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params'
boot
Geah Heh
Re: Problem booting NSA320 with Linux Kernel 4.12.1-kirkwood-tld-1 April 13, 2018 10:53PM |
NSA320> setenv mtdparts 'nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)' NSA320> setenv set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params'
bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init bootcmd=nand read.e 0x2000000 $(kernel_addr) 0xA00000; bootm 0x2000000 bootdelay=2 baudrate=115200 loads_echo=0 eth1addr=00:19:CB:00:51:82 ipaddr=10.4.50.165 serverip=10.4.50.5 rootpath=/mnt/ARM_FS/ netmask=255.255.255.0 nandEcc=1bit kernel_addr=480000 MODEL_ID=DD01 PRODUCT_NAME=NSA-320 FEATURE_BIT=00 CONTRY_TYPE=FF VENDOR_NAME=ZyXEL Communications Corp. run_diag=yes ethaddr=C8:6C:87:F8:3E:B9
Re: Problem booting NSA320 with Linux Kernel 4.12.1-kirkwood-tld-1 April 13, 2018 10:57PM |
Admin Registered: 13 years ago Posts: 18,560 |
Geah Heh
Re: Problem booting NSA320 with Linux Kernel 4.12.1-kirkwood-tld-1 April 13, 2018 10:59PM |
Geah Heh
Re: Problem booting NSA320 with Linux Kernel 4.12.1-kirkwood-tld-1 April 13, 2018 11:15PM |
Re: Problem booting NSA320 with Linux Kernel 4.12.1-kirkwood-tld-1 April 14, 2018 12:07AM |
Admin Registered: 13 years ago Posts: 18,560 |
fw_setenv mtdparts 'mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)'
Geah Heh
Re: Problem booting NSA320 with Linux Kernel 4.12.1-kirkwood-tld-1 April 14, 2018 04:21AM |
fw_setenv mtdparts 'orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)'
fw_setenv mtdparts 'mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)'
root@debian:~# fw_printenv mtdparts mtdparts=mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)
Re: Problem booting NSA320 with Linux Kernel 4.12.1-kirkwood-tld-1 April 14, 2018 04:34AM |
Admin Registered: 13 years ago Posts: 18,560 |
mtdparts=mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)
Geah Heh
Re: Problem booting NSA320 with Linux Kernel 4.12.1-kirkwood-tld-1 April 14, 2018 06:23AM |