Debian on Dell Kace M300
Posted by JDS420
|
Re: Dell Appliance July 27, 2019 02:10PM |
Registered: 9 years ago Posts: 226 |
bodhi Wrote:
-------------------------------------------------------
> All,
>
> I plan to revisit the 2GB RAM issue on this box.
> Please remind me in a few weeks if I forget.
Cool! I've been wanting to dig mine out for a while now, but other priorities keep getting in the way. I've been pushing my beloved Dockstar too hard and I'm tired of the OOM killer kicking in, so it would be nice to have 2GB of RAM. :-)
Let me know if I can help in any way.
-JT
-------------------------------------------------------
> All,
>
> I plan to revisit the 2GB RAM issue on this box.
> Please remind me in a few weeks if I forget.
Cool! I've been wanting to dig mine out for a while now, but other priorities keep getting in the way. I've been pushing my beloved Dockstar too hard and I'm tired of the OOM killer kicking in, so it would be nice to have 2GB of RAM. :-)
Let me know if I can help in any way.
-JT
|
Re: Dell Appliance August 17, 2019 03:57PM |
Admin Registered: 13 years ago Posts: 18,543 |
The bad news is similar HighMem errors still exist in the latest kernel (5.2.8). It happens less often than in previous kernel version, though. Similar problem has been reported to mainline last year, but looks like the devs don't like to spend much time on ARMV5 (armel) anymore.
The Kirkwood kernel we have will run this M300 box with 768K RAM. So if anybody is having OOM running Dockstar or other Kirkwood plugs, perhaps you should start using this box with 768K for now.
I think I will need to build a different kernel for this box. Not giving up yet :)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
The Kirkwood kernel we have will run this M300 box with 768K RAM. So if anybody is having OOM running Dockstar or other Kirkwood plugs, perhaps you should start using this box with 768K for now.
I think I will need to build a different kernel for this box. Not giving up yet :)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Dell Appliance August 27, 2019 09:39AM |
Registered: 9 years ago Posts: 39 |
Hi guys,
Frequent lurker, but infrequent poster here. After I stumbled on this thread, I picked one of these up for $10 after $5 ebay coupon. Got Debian booted from a thumb drive using bodhi's instructions. This looks like a nice souped up version of a pogoplug. If the 2 GB issue can get resolved, it would open up some interesting possibilities. For instance I've found Nextcloud is not really usable on a pogo (I've tried) but with 2 GB ram and faster CPU it may be possible.
I installed on an old PNY 8 GB thumb drive, which seems a bit flakey as sometimes uboot locks up after running "usb start". I just got a couple of SanDisk 32 GB Ultra Fit which I will use instead.
Barring any fix for the RAM issue, what about keeping stock OS (or at least the kernel) and ripping out the Dell proprietary stuff? I know it's old, but it does see the full 2 GB. I guess there could be issues installing new packages etc.
Neal
Frequent lurker, but infrequent poster here. After I stumbled on this thread, I picked one of these up for $10 after $5 ebay coupon. Got Debian booted from a thumb drive using bodhi's instructions. This looks like a nice souped up version of a pogoplug. If the 2 GB issue can get resolved, it would open up some interesting possibilities. For instance I've found Nextcloud is not really usable on a pogo (I've tried) but with 2 GB ram and faster CPU it may be possible.
I installed on an old PNY 8 GB thumb drive, which seems a bit flakey as sometimes uboot locks up after running "usb start". I just got a couple of SanDisk 32 GB Ultra Fit which I will use instead.
Barring any fix for the RAM issue, what about keeping stock OS (or at least the kernel) and ripping out the Dell proprietary stuff? I know it's old, but it does see the full 2 GB. I guess there could be issues installing new packages etc.
Neal
|
Re: Dell Appliance August 28, 2019 12:49AM |
Registered: 9 years ago Posts: 442 |
|
Re: Dell Appliance August 28, 2019 04:04AM |
Admin Registered: 13 years ago Posts: 18,543 |
> Not likely a good idea as the stock OS is Linux
> 2.6.31 which is absolutely ancient and likely
> contains many known exploits.
Agree.
As I said, I'm still finding ways to get around this problem. I know very likely it can be run at full 1GB with some different config. But I am still trying for 2GB!
Hopefully I will upload a new kernel for testing soon.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> 2.6.31 which is absolutely ancient and likely
> contains many known exploits.
Agree.
As I said, I'm still finding ways to get around this problem. I know very likely it can be run at full 1GB with some different config. But I am still trying for 2GB!
Hopefully I will upload a new kernel for testing soon.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Dell Appliance August 28, 2019 05:15PM |
Admin Registered: 13 years ago Posts: 18,543 |
This kernel is configured without HighMem, every thing is running in low memory.
Download at Dropbox
linux-5.2.9-kirkwood-tld-2.bodhi.tar.bz2
md5:
006bd0efb77a90165c54e02862679fe0
sha256:
a0a4b8e008d7fd7e79c611f99939fbd1035651639b6c5eb0b8524a39f0393744
There are 5 files in this tarball:
The installation is same as in the kernel release thread.
I forgot to include the DTB tarball! But I'm asuming that kernel linux-5.2.9-kirkwood-tld-1 already installed. In case you have not installed previous kernel, I also attached the M300 DTB here in this post.
System Info
root@M300:~# uname -a
root@M300:~# free -h
root@M300:~# cat /proc/meminfo
root@M300:~# dmesg | head -30
root@M300:~# uptime
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 2 time(s). Last edit at 08/28/2019 05:35PM by bodhi.
Download at Dropbox
linux-5.2.9-kirkwood-tld-2.bodhi.tar.bz2
md5:
006bd0efb77a90165c54e02862679fe0
sha256:
a0a4b8e008d7fd7e79c611f99939fbd1035651639b6c5eb0b8524a39f0393744
There are 5 files in this tarball:
linux-image-5.2.9-kirkwood-tld-2_2.0_armel.deb linux-headers-5.2.9-kirkwood-tld-2_2.0_armel.deb zImage-5.2.9-kirkwood-tld-2 config-5.2.9-kirkwood-tld-2 linux-5.2.9-kirkwood-tld-1.patch
The installation is same as in the kernel release thread.
I forgot to include the DTB tarball! But I'm asuming that kernel linux-5.2.9-kirkwood-tld-1 already installed. In case you have not installed previous kernel, I also attached the M300 DTB here in this post.
System Info
root@M300:~# uname -a
Linux M300 5.2.9-kirkwood-tld-2 #1 PREEMPT Wed Aug 28 03:55:21 PDT 2019 armv5tel GNU/Linux
root@M300:~# free -h
total used free shared buff/cache available
Mem: 1.7G 29M 1.6G 6.8M 100M 1.7G
Swap: 511M 0B 511M
root@M300:~# cat /proc/meminfo
MemTotal: 1804532 kB MemFree: 1671008 kB MemAvailable: 1741072 kB Buffers: 14284 kB Cached: 81704 kB SwapCached: 0 kB Active: 63856 kB Inactive: 46136 kB Active(anon): 14160 kB Inactive(anon): 6768 kB Active(file): 49696 kB Inactive(file): 39368 kB Unevictable: 0 kB Mlocked: 0 kB SwapTotal: 524284 kB SwapFree: 524284 kB Dirty: 0 kB Writeback: 0 kB AnonPages: 14012 kB Mapped: 27368 kB Shmem: 6932 kB KReclaimable: 7052 kB Slab: 12904 kB SReclaimable: 7052 kB SUnreclaim: 5852 kB KernelStack: 824 kB PageTables: 1200 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 1426548 kB Committed_AS: 53860 kB VmallocTotal: 245760 kB VmallocUsed: 0 kB VmallocChunk: 0 kB Percpu: 96 kB
root@M300:~# dmesg | head -30
[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.2.9-kirkwood-tld-2 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 PREEMPT Wed Aug 28 03:55:21 PDT 2019 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: Dell KACE M300 [ 0.000000] printk: bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Ignoring RAM at 0x70000000-0x80000000 [ 0.000000] Consider using a HIGHMEM enabled kernel. [ 0.000000] On node 0 totalpages: 458752 [ 0.000000] Normal zone: 3584 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 458752 pages, LIFO batch:63 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 455168 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) earlyprintk=serial [ 0.000000] Dentry cache hash table entries: 262144 (order: 8, 1048576 bytes) [ 0.000000] Inode-cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Memory: 1795408K/1835008K available (9216K kernel code, 868K rwdata, 3400K rodata, 1024K init, 300K bss, 39600K reserved, 0K cma-reserved)
root@M300:~# uptime
15:29:32 up 1:41, 1 user, load average: 0.00, 0.00, 0.00
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 2 time(s). Last edit at 08/28/2019 05:35PM by bodhi.
|
Re: Dell Appliance August 28, 2019 05:35PM |
Admin Registered: 13 years ago Posts: 18,543 |
Please see the post above for download link.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Dell Appliance August 28, 2019 05:57PM |
Admin Registered: 13 years ago Posts: 18,543 |
@Neal,
Please give it a shot! I think your use case is the best test case for this kernel memory capacity.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 08/28/2019 05:58PM by bodhi.
Please give it a shot! I think your use case is the best test case for this kernel memory capacity.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 08/28/2019 05:58PM by bodhi.
|
Re: Dell Appliance August 28, 2019 07:39PM |
Admin Registered: 13 years ago Posts: 18,543 |
Stress tests.
Memory 1.7G
root@M300:~# stress-ng --vm 2 --vm-bytes 1700M --timeout 60s
CPU max
root@M300:~# stress-ng --cpu 64 --cpu-method all --verify -t 5m --metrics-brief
CPU and Memory
root@M300:~# stress-ng --cpu 64 --cpu-method all --verify -t 5m --metrics-brief --vm 2 --vm-bytes 1700M
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Memory 1.7G
root@M300:~# stress-ng --vm 2 --vm-bytes 1700M --timeout 60s
stress-ng: info: [3323] dispatching hogs: 2 vm stress-ng: info: [3323] cache allocate: using built-in defaults as unable to determine cache details stress-ng: info: [3323] cache allocate: default cache size: 2048K stress-ng: info: [3323] successful run completed in 74.66s (1 min, 14.66 secs)
CPU max
root@M300:~# stress-ng --cpu 64 --cpu-method all --verify -t 5m --metrics-brief
stress-ng: info: [3336] dispatching hogs: 64 cpu stress-ng: info: [3336] cache allocate: using built-in defaults as unable to determine cache details stress-ng: info: [3336] cache allocate: default cache size: 2048K stress-ng: info: [3336] successful run completed in 316.25s (5 mins, 16.25 secs) stress-ng: info: [3336] stressor bogo ops real time usr time sys time bogo ops/s bogo ops/s stress-ng: info: [3336] (secs) (secs) (secs) (real time) (usr+sys time) stress-ng: info: [3336] cpu 640 312.87 306.39 0.12 2.05 2.09
CPU and Memory
root@M300:~# stress-ng --cpu 64 --cpu-method all --verify -t 5m --metrics-brief --vm 2 --vm-bytes 1700M
stress-ng: info: [3418] dispatching hogs: 64 cpu, 2 vm stress-ng: info: [3418] cache allocate: using built-in defaults as unable to determine cache details stress-ng: info: [3418] cache allocate: default cache size: 2048K stress-ng: info: [3418] successful run completed in 323.24s (5 mins, 23.24 secs) stress-ng: info: [3418] stressor bogo ops real time usr time sys time bogo ops/s bogo ops/s stress-ng: info: [3418] (secs) (secs) (secs) (real time) (usr+sys time) stress-ng: info: [3418] cpu 632 319.17 306.03 0.07 1.98 2.06
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Dell Appliance August 28, 2019 07:52PM |
Registered: 7 years ago Posts: 366 |
|
Re: Dell Appliance August 28, 2019 10:22PM |
Admin Registered: 13 years ago Posts: 18,543 |
> Great news! Thank you! Bodhi!
You're welcome David! looking forward to your tests whenever you get to use it for real applications.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
You're welcome David! looking forward to your tests whenever you get to use it for real applications.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Dell Appliance August 29, 2019 06:59AM |
Registered: 9 years ago Posts: 39 |
|
Re: Debian on Dell Kace M300 August 29, 2019 05:39PM |
Registered: 10 years ago Posts: 155 |
I'm trying to install the new kernel and ran into a problem. First, i"m trying to install the 5.2.9 kernel on the usb with the 4.12.2 kernel and filesystem that was first used on the M300 last year. Is that a mistake and I should Install the 5.2.9 filesystem and kernel, and then update to this latest kernel? The problem with my "hybrid" system is that there is no initramfs-5.2.9 file so the mkimage fails when trying to make uInitrd.
Thanks for the help.
Thanks for the help.
|
Re: Debian on Dell Kace M300 August 29, 2019 05:57PM |
Admin Registered: 13 years ago Posts: 18,543 |
mikeh49,
> I'm trying to install the new kernel and ran into
> a problem. First, i"m trying to install the 5.2.9
> kernel on the usb with the 4.12.2 kernel and
> filesystem that was first used on the M300 last
> year. Is that a mistake and I should Install the
> 5.2.9 filesystem and kernel, and then update to
> this latest kernel?
Not a mistake, you can install kernel 5.2.9 when running any previous version.
> The problem with my "hybrid"
> system is that there is no initramfs-5.2.9 file so
> the mkimage fails when trying to make uInitrd.
I am sure what "hybrid" system means?
initrd.img-5.2.9-kirkwood-tld-1 is generated when you run dpkg to install linux-image-5.2.9-kirkwood-tld-1_1.0_armel.deb.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> I'm trying to install the new kernel and ran into
> a problem. First, i"m trying to install the 5.2.9
> kernel on the usb with the 4.12.2 kernel and
> filesystem that was first used on the M300 last
> year. Is that a mistake and I should Install the
> 5.2.9 filesystem and kernel, and then update to
> this latest kernel?
Not a mistake, you can install kernel 5.2.9 when running any previous version.
> The problem with my "hybrid"
> system is that there is no initramfs-5.2.9 file so
> the mkimage fails when trying to make uInitrd.
I am sure what "hybrid" system means?
initrd.img-5.2.9-kirkwood-tld-1 is generated when you run dpkg to install linux-image-5.2.9-kirkwood-tld-1_1.0_armel.deb.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on Dell Kace M300 August 29, 2019 06:07PM |
Registered: 10 years ago Posts: 155 |
Thanks, I may not have run the dpkg, I'll go back and review. I've been having linux and windows box problems, so it's been messy. Hybrid is 4.12 filesystem with 5.2.9 kernel.
BTW, what do you guys use for this kind of work - Linux box using Terminal, Windows with Putty, or some way to use LInux with root privileges from a GUI? Lots of typing or copying and pasting without a GUI.
BTW, what do you guys use for this kind of work - Linux box using Terminal, Windows with Putty, or some way to use LInux with root privileges from a GUI? Lots of typing or copying and pasting without a GUI.
|
Re: Debian on Dell Kace M300 August 29, 2019 07:33PM |
Registered: 10 years ago Posts: 155 |
It is now working. I set up the USB on the M300 running the stock kernel and OS. I ran the dpkg command from the /tmp/usb/boot directory (/tmp/usb was the mount point of the USB) and it put the initramfs file in the boot directory of the M300 filesystem and the kernel modules in the /lib/modules directory of the M300 filesystem also. I'll look into dpkg to see if the install directory can be forced, or perhaps it in the setup of the .deb package? It seems like this would be a common use case where the kirkwood USB is setup on another linux box.
After moving the initramfs file and the kernel modules to the usb, running the mkimage for uInitrd, it booted into the new kernel. Is there any reason for me to run the stress tests? Is there a simple to install app that would test the memory size?
After moving the initramfs file and the kernel modules to the usb, running the mkimage for uInitrd, it booted into the new kernel. Is there any reason for me to run the stress tests? Is there a simple to install app that would test the memory size?
|
Re: Debian on Dell Kace M300 August 29, 2019 08:30PM |
Admin Registered: 13 years ago Posts: 18,543 |
mikeh49,
You have done it the wrong way.
dpkg needs to be run on a live system booting a previous kernel. And it will automatically populate the rootfs /boot and /lib/modules/, and also records the linux-Image-xxxx the rootfs.
> I'll look into dpkg to see if the install
> directory can be forced, or perhaps it in the
> setup of the .deb package? It seems like this
> would be a common use case where the kirkwood USB
> is setup on another linux box.
>
> After moving the initramfs file and the kernel
> modules to the usb, running the mkimage for
> uInitrd, it booted into the new kernel.
Even though it booted, the roofts is not correct.
> Is there
> any reason for me to run the stress tests? I.
> there a simple to install app that would test the
> memory size?
Not sure if we should proceed. Until I see your kernel installation log, I am not sure.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
You have done it the wrong way.
dpkg needs to be run on a live system booting a previous kernel. And it will automatically populate the rootfs /boot and /lib/modules/, and also records the linux-Image-xxxx the rootfs.
> I'll look into dpkg to see if the install
> directory can be forced, or perhaps it in the
> setup of the .deb package? It seems like this
> would be a common use case where the kirkwood USB
> is setup on another linux box.
>
> After moving the initramfs file and the kernel
> modules to the usb, running the mkimage for
> uInitrd, it booted into the new kernel.
Even though it booted, the roofts is not correct.
> Is there
> any reason for me to run the stress tests? I.
> there a simple to install app that would test the
> memory size?
Not sure if we should proceed. Until I see your kernel installation log, I am not sure.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on Dell Kace M300 August 29, 2019 09:27PM |
Registered: 10 years ago Posts: 155 |
|
Re: Debian on Dell Kace M300 August 29, 2019 09:45PM |
Registered: 10 years ago Posts: 155 |
Here's the log from serial console:
I see the lines were truncated. Hope that's OK.
Hit any key to stop autoboot: 0 Marvell>> setenv mtdparts 'mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boo t-env)' Marvell>> setenv set_bootargs_usb 'setenv bootargs console=ttyS0,115200 root=LAB EL=rootfs rootdelay=10 $(mtdparts) earlyprintk=serial Marvell>> usb start (Re)start USB... USB: scanning bus for devices... 3 USB Device(s) found Waiting for storage device(s) to settle before scanning... 1 Storage Device(s) found Marvell>> ext2load usb 0:1 0x800000 /boot/uImage .... ................................................................................ ................................................................................ ................................................................................ ................................................................................ ................................................................................ ......... ........................................................................ 4981628 bytes read Marvell>> ext2load usb 0:1 0x02100000 /boot/uInitrd .... ................................................................................ ................................................................................ ................................................. 2190934 bytes read Marvell>> run set_bootargs_usb Marvell>> bootm 0x800000 0x02100000 ## Booting image at 00800000 ... Image Name: Linux-5.2.9-kirkwood-tld-2 Created: 2019-08-29 22:30:20 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4981564 Bytes = 4.8 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 02100000 ... Image Name: initramfs-5.2.9-kirkwood-tld-2 Created: 2019-08-30 0:32:45 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 2190870 Bytes = 2.1 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.2.9-kirkwood-tld-2 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 PREEMPT Wed Aug 28 03:55:21 PDT 2019 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr =0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Dell KACE M300 [ 0.000000][ T0] printk: bootconsole [earlycon0] enabled [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Ignoring RAM at 0x70000000-0x80000000 [ 0.000000][ T0] Consider using a HIGHMEM enabled kernel. [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 45 5168 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=root fs rootdelay=10 mtdparts=spi0.0:0x7f000@0(uboot),0x1000@0x7f000(u-boot-env) earl yprintk=serial [ 0.000000][ T0] Dentry cache hash table entries: 262144 (order: 8, 104857 6 bytes) [ 0.000000][ T0] Inode-cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000][ T0] Memory: 1801368K/1835008K available (9216K kernel code, 8 68K rwdata, 3400K rodata, 1024K init, 300K bss, 33640K reserved, 0K cma-reserved ) [ 0.000000][ T0] random: get_random_u32 called from cache_alloc_refill+0x5 2c/0x924 with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay i s 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycl es: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000006][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps eve ry 10737418237ns [ 0.008508][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.015620][ T0] Console: colour dummy device 80x30 [ 0.020794][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.031996][ T0] pid_max: default: 32768 minimum: 301 [ 0.037549][ T0] LSM: Security Framework initializing [ 0.043015][ T0] Mount-cache hash table entries: 4096 (order: 2, 16384 byt es) [ 0.050428][ T0] Mountpoint-cache hash table entries: 4096 (order: 2, 1638 4 bytes) [ 0.058875][ T0] *** VALIDATE proc *** [ 0.063067][ T0] *** VALIDATE cgroup1 *** [ 0.067325][ T0] *** VALIDATE cgroup2 *** [ 0.071672][ T0] CPU: Testing write buffer coherency: ok [ 0.078504][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.085566][ T1] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1 [ 0.091620][ T1] rcu: Hierarchical SRCU implementation. [ 0.099335][ T1] devtmpfs: initialized [ 0.106991][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffff ffff, max_idle_ns: 19112604462750000 ns [ 0.117538][ T1] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.124559][ T1] xor: measuring software checksum speed [ 0.228527][ T1] arm4regs : 1816.800 MB/sec [ 0.328530][ T1] 8regs : 1090.400 MB/sec [ 0.428527][ T1] 32regs : 1585.600 MB/sec [ 0.433382][ T1] xor: using function: arm4regs (1816.800 MB/sec) [ 0.439651][ T1] prandom: seed boundary self test passed [ 0.447698][ T1] prandom: 100 self tests passed [ 0.452493][ T1] pinctrl core: initialized pinctrl subsystem [ 0.459516][ T1] NET: Registered protocol family 16 [ 0.465021][ T1] DMA: preallocated 256 KiB pool for atomic coherent alloca tions [ 0.473237][ T1] audit: initializing netlink subsys (disabled) [ 0.480304][ T14] audit: type=2000 audit(0.470:1): state=initialized audit_ enabled=0 res=1 [ 0.488811][ T1] cpuidle: using governor ladder [ 0.493637][ T1] cpuidle: using governor menu [ 0.498645][ T1] Feroceon L2: Enabling L2 [ 0.502918][ T1] Feroceon L2: Cache support initialised. [ 0.512266][ T1] No ATAGs? [ 2.568513][ C0] random: fast init done [ 3.736804][ T71] alg: No test for lzo-rle (lzo-rle-generic) [ 3.742954][ T73] alg: No test for lzo-rle (lzo-rle-scomp) [ 3.918814][ T1] raid6: int32x8 gen() 208 MB/s [ 4.088869][ T1] raid6: int32x8 xor() 142 MB/s [ 4.258590][ T1] raid6: int32x4 gen() 208 MB/s [ 4.428663][ T1] raid6: int32x4 xor() 138 MB/s [ 4.598693][ T1] raid6: int32x2 gen() 210 MB/s [ 4.768668][ T1] raid6: int32x2 xor() 152 MB/s [ 4.938707][ T1] raid6: int32x1 gen() 157 MB/s [ 5.108551][ T1] raid6: int32x1 xor() 109 MB/s [ 5.113485][ T1] raid6: using algorithm int32x2 gen() 210 MB/s [ 5.119552][ T1] raid6: .... xor() 152 MB/s, rmw enabled [ 5.125097][ T1] raid6: using intx1 recovery algorithm [ 5.130667][ T1] vgaarb: loaded [ 5.134392][ T1] SCSI subsystem initialized [ 5.139191][ T1] usbcore: registered new interface driver usbfs [ 5.145376][ T1] usbcore: registered new interface driver hub [ 5.151430][ T1] usbcore: registered new device driver usb [ 5.157260][ T1] pps_core: LinuxPPS API ver. 1 registered [ 5.162905][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodol fo Giometti <giometti@linux.it> [ 5.172703][ T1] PTP clock support registered [ 5.178234][ T1] clocksource: Switched to clocksource orion_clocksource [ 5.790925][ T1] VFS: Disk quotas dquot_6.6.0 [ 5.795592][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 5.809916][ T1] NET: Registered protocol family 2 [ 5.815521][ T1] tcp_listen_portaddr_hash hash table entries: 1024 (order: 1, 8192 bytes) [ 5.824011][ T1] TCP established hash table entries: 16384 (order: 4, 6553 6 bytes) [ 5.832025][ T1] TCP bind hash table entries: 16384 (order: 4, 65536 bytes ) [ 5.839428][ T1] TCP: Hash tables configured (established 16384 bind 16384 ) [ 5.846700][ T1] UDP hash table entries: 1024 (order: 2, 16384 bytes) [ 5.853432][ T1] UDP-Lite hash table entries: 1024 (order: 2, 16384 bytes) [ 5.860740][ T1] NET: Registered protocol family 1 [ 5.866230][ T1] RPC: Registered named UNIX socket transport module. [ 5.872872][ T1] RPC: Registered udp transport module. [ 5.878253][ T1] RPC: Registered tcp transport module. [ 5.883620][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 5.890732][ T1] PCI: CLS 0 bytes, default 32 [ 5.895487][ T1] Trying to unpack rootfs image as initramfs... [ 6.005716][ T1] Freeing initrd memory: 2140K [ 6.010559][ T1] NetWinder Floating Point Emulator V0.97 (double precision ) [ 6.018711][ T1] Initialise system trusted keyrings [ 6.023851][ T1] Key type blacklist registered [ 6.028767][ T1] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 6.035919][ T1] zbud: loaded [ 6.039951][ T1] NFS: Registering the id_resolver key type [ 6.045684][ T1] Key type id_resolver registered [ 6.050597][ T1] Key type id_legacy registered [ 6.055281][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering ... [ 6.062655][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 6.069910][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat , Inc. [ 6.077761][ T1] fuse: init (API version 7.31) [ 6.082748][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 6.090001][ T1] orangefs_init: module version upstream loaded [ 6.096061][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, no debug enabled [ 6.110144][ T1] async_tx: api initialized (async) [ 6.115177][ T1] Key type asymmetric registered [ 6.120008][ T1] Asymmetric key parser 'x509' registered [ 6.125595][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 6.134702][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinc trl driver [ 6.144035][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge t o bus 0000:00 [ 6.152331][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 6.158498][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefff ffff] [ 6.166031][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 6.173037][ T1] pci 0000:00:01.0: [11ab:6282] type 01 class 0x060400 [ 6.179743][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pr ef] [ 6.187839][ T1] PCI: bus0: Fast back to back transfers disabled [ 6.194109][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-0 0]), reconfiguring [ 6.203440][ T1] PCI: bus1: Fast back to back transfers enabled [ 6.209620][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 6.217014][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe0000 7ff pref] [ 6.224915][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 6.230951][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 6.298754][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 6.307990][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 6.368750][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 6.378172][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 6.386095][ T1] printk: console [ttyS0] disabled [ 6.391133][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base _baud = 12500000) is a 16550A [ 6.400800][ T1] printk: console [ttyS0] enabled [ 6.400800][ T1] printk: console [ttyS0] enabled [ 6.410620][ T1] printk: bootconsole [earlycon0] disabled [ 6.410620][ T1] printk: bootconsole [earlycon0] disabled [ 6.427270][ T1] loop: module loaded [ 6.431591][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 6.439123][ T1] scsi host0: sata_mv [ 6.443391][ T1] scsi host1: sata_mv [ 6.447461][ T1] ata1: SATA max UDMA/133 irq 33 [ 6.452323][ T1] ata2: SATA max UDMA/133 irq 33 [ 6.458378][ T1] m25p80 spi0.0: mx25l4005a (512 Kbytes) [ 6.463896][ T1] 2 cmdlinepart partitions found on MTD device spi0.0 [ 6.470575][ T1] Creating 2 MTD partitions on "spi0.0": [ 6.476088][ T1] 0x000000000000-0x00000007f000 : "uboot" [ 6.482636][ T1] 0x00000007f000-0x000000080000 : "u-boot-env" [ 6.490313][ T1] libphy: Fixed MDIO Bus: probed [ 6.495661][ T1] libphy: orion_mdio_bus: probed [ 6.504275][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 6.512178][ T1] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set [ 6.520098][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 18:03:73:41:db:3e [ 6.529724][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Drive r [ 6.536994][ T1] ehci-pci: EHCI PCI platform driver [ 6.542242][ T1] ehci-orion: EHCI orion driver [ 6.547097][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 6.553373][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigne d bus number 1 [ 6.561932][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 6.598259][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 6.605180][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct= 0002, bcdDevice= 5.02 [ 6.614196][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, Seria lNumber=1 [ 6.622159][ T1] usb usb1: Product: EHCI Host Controller [ 6.627752][ T1] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-2 ehci_h cd [ 6.635108][ T1] usb usb1: SerialNumber: f1050000.ehci [ 6.640958][ T1] hub 1-0:1.0: USB hub found [ 6.645445][ T1] hub 1-0:1.0: 1 port detected [ 6.650596][ T1] usbcore: registered new interface driver usb-storage [ 6.657588][ T1] mousedev: PS/2 mouse device common for all mice [ 6.664319][ T1] rtc-mv f1010300.rtc: registered as rtc0 [ 6.670050][ T1] i2c /dev entries driver [ 6.674696][ T1] device-mapper: uevent: version 1.0.3 [ 6.680301][ T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialis ed: dm-devel@redhat.com [ 6.689797][ T1] device-mapper: multipath round-robin: version 1.2.0 loade d [ 6.697080][ T1] device-mapper: multipath queue-length: version 0.2.0 load ed [ 6.704462][ T1] device-mapper: multipath service-time: version 0.3.0 load ed [ 6.711892][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 6.718769][ T1] device-mapper: raid: Loading target version 1.14.0 [ 6.725747][ T1] kirkwood-pinctrl f1010000.pin-controller: unsupported fun ction gpio on pin mpp7 [ 6.734881][ T1] pinctrl core: failed to register map default (0): invalid type given [ 6.743039][ T1] leds-gpio: probe of gpio-leds failed with error -22 [ 6.749804][ T1] hidraw: raw HID events driver (C) Jiri Kosina [ 6.756164][ T1] drop_monitor: Initializing network drop monitor service [ 6.763466][ T1] NET: Registered protocol family 17 [ 6.768853][ T1] Key type dns_resolver registered [ 6.774446][ T1] registered taskstats version 1 [ 6.779303][ T1] Loading compiled-in X.509 certificates [ 6.784893][ T1] zswap: loaded using pool lzo/zbud [ 6.817078][ T1] Key type big_key registered [ 6.832533][ T1] Key type encrypted registered [ 6.838782][ T1] rtc-mv f1010300.rtc: setting system clock to 2019-08-30T0 0:38:02 UTC (1567125482) [ 6.958271][ T112] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 6.969754][ T112] ata1.00: ATA-7: TS16GSSD25H-M, 20100712, max UDMA/133 [ 6.976569][ T112] ata1.00: 31277056 sectors, multi 0: LBA48 [ 6.989116][ T112] ata1.00: configured for UDMA/133 [ 7.004481][ T7] scsi 0:0:0:0: Direct-Access ATA TS16GSSD25H-M 0712 PQ: 0 ANSI: 5 [ 7.014105][ T116] sd 0:0:0:0: [sda] 31277056 512-byte logical blocks: (16.0 GB/14.9 GiB) [ 7.022443][ T15] usb 1-1: new high-speed USB device number 2 using orion-e hci [ 7.030310][ T116] sd 0:0:0:0: [sda] Write Protect is off [ 7.035993][ T116] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabl ed, doesn't support DPO or FUA [ 7.047649][ T116] sda: sda1 sda2 sda3 < sda5 > [ 7.053845][ T116] sd 0:0:0:0: [sda] Attached SCSI disk [ 7.228693][ T15] usb 1-1: New USB device found, idVendor=058f, idProduct=6 254, bcdDevice= 1.00 [ 7.237614][ T15] usb 1-1: New USB device strings: Mfr=0, Product=0, Serial Number=0 [ 7.245915][ T15] hub 1-1:1.0: USB hub found [ 7.250560][ T15] hub 1-1:1.0: 4 ports detected [ 7.361774][ T114] ata2: SATA link down (SStatus 0 SControl F300) [ 7.381222][ T1] Freeing unused kernel memory: 1024K [ 7.386854][ T1] Checked W+X mappings: passed, no W+X pages found [ 7.393257][ T1] Run /init as init process Loading, please wait... [ 7.462121][ T158] udev[158]: starting version 164 [ 7.568324][ T15] usb 1-1.2: new high-speed USB device number 3 using orion -ehci [ 7.731336][ T15] usb 1-1.2: New USB device found, idVendor=03f0, idProduct =b107, bcdDevice= 1.00 [ 7.748072][ T15] usb 1-1.2: New USB device strings: Mfr=1, Product=2, Seri alNumber=3 [ 7.764753][ T15] usb 1-1.2: Product: USB Flash Drive [ 7.775594][ T15] usb 1-1.2: Manufacturer: HP [ 7.784724][ T15] usb 1-1.2: SerialNumber: UT1A026200001561 [ 7.797628][ T15] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 7.816455][ T15] scsi host2: usb-storage 1-1.2:1.0 [ 8.899137][ T23] scsi 2:0:0:0: Direct-Access hp USB FLASH DRIVE 0.00 PQ: 0 ANSI: 2 [ 8.915115][ T116] sd 2:0:0:0: [sdb] 7892992 512-byte logical blocks: (4.04 GB/3.76 GiB) [ 8.927349][ T116] sd 2:0:0:0: [sdb] Write Protect is off [ 8.933330][ T116] sd 2:0:0:0: [sdb] Asking for cache data failed [ 8.939631][ T116] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 8.952676][ T116] sdb: sdb1 [ 8.964474][ T116] sd 2:0:0:0: [sdb] Attached SCSI removable disk Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. [ 18.047981][ T244] EXT4-fs (sdb1): mounting ext3 file system using the ext4 subsystem [ 18.101503][ T244] EXT4-fs (sdb1): mounted filesystem with ordered data mode . Opts: (null) Begin: Running /scripts/local-bottom ... done. done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [ ok ] Setting hostname to 'debian'...done. [....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232 [ ok [ 19.918953][ T421] random: systemd-udevd: uninitialized urandom read (1 6 bytes read) [ 19.936504][ T421] random: systemd-udevd: uninitialized urandom read (16 byt es read) [ 19.949596][ T421] random: systemd-udevd: uninitialized urandom read (16 byt es read) . [ ok ] Synthesizing the initial hotplug events...done. [....] Waiting for /dev to be fully populated...[ 20.340445][ T445] input: gp io_keys as /devices/platform/gpio_keys/input/input0 [ 20.469823][ T447] watchdog: f1020300.watchdog-timer: driver supplied timeou t (4294967295) out of range [ 20.516433][ T447] watchdog: f1020300.watchdog-timer: falling back to defaul t timeout (21) [ 20.552411][ T447] orion_wdt: Initial timeout 21 sec [ 20.582786][ T444] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 20.610688][ T444] sd 2:0:0:0: Attached scsi generic sg1 type 0 [ 20.644768][ T447] usbcore: registered new interface driver uas [ 20.815251][ T446] marvell-cesa f1030000.crypto: CESA device successfully re gistered done. [ ok ] Activating swap:. [ 21.748350][ T635] EXT4-fs (sdb1): re-mounted. Opts: (null) [....] Will now check root file system:fsck from util-linux 2.29.2 [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sdb1 e2fsck 1.43.4 (31-Jan-2017) rootfs: clean, 17164/247008 files, 204703/986368 blocks . ok [ 21.938499][ C0] random: crng init done [ 21.942631][ C0] random: 7 urandom warning(s) missed due to ratelimiting [ 21.949692][ T661] EXT4-fs (sdb1): re-mounted. Opts: errors=remount-ro [ ok ] Will now activate lvm and md swap:done. [info] Will now check all file systems. fsck from util-linux 2.29.2 Checking all file systems. LABEL=rootfs is mounted [....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs [ ok hat location is writable.. [ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done. [ ok . [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables...done. [ ok ] Initializing random number generator...done. [ 26.474988][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb /s, full duplex, flow control disabled [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5 Copyright 2004-2016 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/18:03:73:41:db:3e Sending on LPF/eth0/18:03:73:41:db:3e Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3 [ 31.541010][ T1223] NET: Registered protocol family 10 [ 31.548615][ T1223] Segment Routing with IPv6 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5 DHCPREQUEST of 192.168.1.104 on eth0 to 255.255.255.255 port 67 DHCPOFFER of 192.168.1.104 from 192.168.1.1 DHCPACK of 192.168.1.104 from 192.168.1.1 bound to 192.168.1.104 -- renewal in 39808 seconds. done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd. .. 1430 (syslogd) . ok [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Starting system message bus: dbus. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1428 (klogd) . ok [ ok ] Running local boot scripts (/etc/rc.local). Debian GNU/Linux 9 debian ttyS0 debian login: root atwPassword: Login incorrect debian login: root Password: Login incorrect debian login: Login Debian GNU/Linux 9 debian ttyS0 debian login: root Password: Login incorrect debian login: root Password: Last login: Thu Oct 11 07:55:21 PDT 2018 on ttyS0 Linux debian 5.2.9-kirkwood-tld-2 #1 PREEMPT Wed Aug 28 03:55:21 PDT 2019 armv5t el The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@debian:~# uname -a Linux debian 5.2.9-kirkwood-tld-2 #1 PREEMPT Wed Aug 28 03:55:21 PDT 2019 armv5t
I see the lines were truncated. Hope that's OK.
|
Re: Debian on Dell Kace M300 August 29, 2019 10:05PM |
Registered: 10 years ago Posts: 155 |
Foolishly did an apt-get update and apt-get update and got the initiramfs issue that you address in the update thread:
Looks to me that it updated the 4.12.1 image file, but I'm running 5.2.9. How should we/you/me handle this?
Processing triggers for initramfs-tools (0.130) ... update-initramfs: Generating /boot/initrd.img-4.12.1-kirkwood-tld-1
Looks to me that it updated the 4.12.1 image file, but I'm running 5.2.9. How should we/you/me handle this?
-rw-r--r-- 1 root root 7713498 Aug 29 19:57 initrd.img-4.12.1-kirkwood-tld-1 -rw-r--r-- 1 root root 2190870 Aug 29 17:32 initrd.img-5.2.9-kirkwood-tld-2
|
Re: Debian on Dell Kace M300 August 30, 2019 12:24AM |
Admin Registered: 13 years ago Posts: 18,543 |
Quote
OK, I'll get the boot log from serial. Is that right? Or, I can do it over while running the 5.2.9 kernel and 4.12 filesystem that is now booted.
As I said,
Quote
dpkg needs to be run on a live system booting a previous kernel. And it will automatically populate the rootfs /boot and /lib/modules/, and also records the linux-Image-xxxx the rootfs.
Quote
Looks to me that it updated the 4.12.1 image file, but I'm running 5.2.9. How should we/you/me handle this?
- What you need to do is create a new USB rootfs using Debian-5.2.9-kirkwood-tld-1-rootfs-bodhi.tar.bz2.
- And boot into the box first.
After you're satisfy that it is working. Then download the kernel package linux-5.2.9-kirkwood-tld-2.bodhi.tar.bz2
And then run the kernel installation similar to what described in the released instruction for kernel linux-5.2.9-kirkwood-tld-1
Quote
Updated 18 Aug 2019:
Kernel linux-5.2.9-kirkwood-tld-1 package has been uploaded. The following features were added/updated:
Do step 1 to 5, but this time using kernel linux-5.2.9-kirkwood-tld-2.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on Dell Kace M300 August 30, 2019 08:20AM |
Registered: 10 years ago Posts: 155 |
|
Re: Debian on Dell Kace M300 August 30, 2019 10:38AM |
Registered: 9 years ago Posts: 39 |
So far, so good:
And here are my stress tests:
Are we at point yet where we feel confident setting the uBoot environment variables to make it boot without having to have a serial console connection? I assume we still need to set them from stock OS...
Neal
root@debian:~# uname -a
Linux debian 5.2.9-kirkwood-tld-2 #1 PREEMPT Wed Aug 28 03:55:21 PDT 2019 armv5tel GNU/Linux
root@debian:~# free -h
total used free shared buff/cache available
Mem: 1.7Gi 15Mi 1.7Gi 0.0Ki 44Mi 1.7Gi
Swap: 0B 0B 0B
And here are my stress tests:
root@debian:~# stress-ng --vm 2 --vm-bytes 1700M --timeout 60s stress-ng: info: [1618] dispatching hogs: 2 vm stress-ng: info: [1618] cache allocate: using defaults, can't determine cache details from sysfs stress-ng: info: [1618] successful run completed in 60.36s (1 min, 0.36 secs) root@debian:~# stress-ng --cpu 64 --cpu-method all --verify -t 5m --metrics-brief stress-ng: info: [1624] dispatching hogs: 64 cpu stress-ng: info: [1624] cache allocate: using defaults, can't determine cache details from sysfs stress-ng: info: [1624] successful run completed in 306.70s (5 mins, 6.70 secs) stress-ng: info: [1624] stressor bogo ops real time usr time sys time bogo ops/s bogo ops/s stress-ng: info: [1624] (secs) (secs) (secs) (real time) (usr+sys time) stress-ng: info: [1624] cpu 1935 303.16 305.97 0.13 6.38 6.32 root@debian:~# stress-ng --cpu 64 --cpu-method all --verify -t 5m --metrics-brief --vm 2 --vm-bytes 1700M stress-ng: info: [1690] dispatching hogs: 64 cpu, 2 vm stress-ng: info: [1690] cache allocate: using defaults, can't determine cache details from sysfs stress-ng: info: [1690] successful run completed in 303.74s (5 mins, 3.74 secs) stress-ng: info: [1690] stressor bogo ops real time usr time sys time bogo ops/s bogo ops/s stress-ng: info: [1690] (secs) (secs) (secs) (real time) (usr+sys time) stress-ng: info: [1690] cpu 1241 301.90 293.83 0.05 4.11 4.22 stress-ng: info: [1690] vm 0 303.20 7.74 1.49 0.00 0.00
Are we at point yet where we feel confident setting the uBoot environment variables to make it boot without having to have a serial console connection? I assume we still need to set them from stock OS...
Neal
|
Re: Debian on Dell Kace M300 August 30, 2019 04:08PM |
Registered: 10 years ago Posts: 155 |
|
Re: Debian on Dell Kace M300 August 30, 2019 05:36PM |
Admin Registered: 13 years ago Posts: 18,543 |
All,
Did you use the box web page during first time installation? and how did you gain root to stock OS without serial console (if you did)?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Did you use the box web page during first time installation? and how did you gain root to stock OS without serial console (if you did)?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on Dell Kace M300 August 30, 2019 06:05PM |
Registered: 10 years ago Posts: 155 |
Bohdi posted this in June 2018:
With this clue, I did the same and can log in as root with my password, via serial, of course. I think the stock OS does not do ssh; I think this was discussed upthread, but couldn't find it quickly.
I did not do anything with the stock web interface beyond a quick look.
Quote
I did it the easy way. After I've booted with the Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2 rootfs, I mounted the internal SATA drive root partition and chroot into it, and reset root password. So now I can login to the box stock OS as root, if needed.
With this clue, I did the same and can log in as root with my password, via serial, of course. I think the stock OS does not do ssh; I think this was discussed upthread, but couldn't find it quickly.
I did not do anything with the stock web interface beyond a quick look.
|
Re: Debian on Dell Kace M300 August 30, 2019 09:02PM |
Registered: 9 years ago Posts: 39 |
bodhi Wrote:
-------------------------------------------------------
> All,
>
> Did you use the box web page during first time
> installation? and how did you gain root to stock
> OS without serial console (if you did)?
I used serial console. I also mounted the SATA and chroot to reset the root password. I never looked at the web page.
Neal
-------------------------------------------------------
> All,
>
> Did you use the box web page during first time
> installation? and how did you gain root to stock
> OS without serial console (if you did)?
I used serial console. I also mounted the SATA and chroot to reset the root password. I never looked at the web page.
Neal
|
Re: Debian on Dell Kace M300 August 30, 2019 11:21PM |
Admin Registered: 13 years ago Posts: 18,543 |
I'm busy with other activities currently, so here are some questions pehaps some of us can investigate.
It would be nice to see what the web page provides. Such as whether SSH can be enabled from there.
Also, is the telnet port opened? if it is, what is the default credential to log in as root?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
It would be nice to see what the web page provides. Such as whether SSH can be enabled from there.
Also, is the telnet port opened? if it is, what is the default credential to log in as root?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian on Dell Kace M300 August 31, 2019 05:08PM |
Registered: 10 years ago Posts: 155 |
Post last year on ssh from the web interface:
Do we need to scan more ports than the just the normal telnet port 23?
Quote
JDS420
In order to enable ssh the way Dell intended, you have to enter a "tether key" which allows customer support to ssh into the box and undo/fix anything someone may have broken. Without a legitimate key, you have you purge all openssh packages and reinstall them. You might have to remove the kace-tether app too, but it's been months since I messed with the internals so I don't remember for sure
Do we need to scan more ports than the just the normal telnet port 23?
|
Re: Debian on Dell Kace M300 August 31, 2019 06:02PM |
Admin Registered: 13 years ago Posts: 18,543 |
> Do we need to scan more ports than the just the
> normal telnet port 23?
If you are inside stock OS, it is easier to see which daemon is running, and what ports are opened.
If no SSH or telnet, we'll just have to live with serial console installation for now.
I'll look at stock u-boot while it is running to see what else we can do.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> normal telnet port 23?
If you are inside stock OS, it is easier to see which daemon is running, and what ports are opened.
If no SSH or telnet, we'll just have to live with serial console installation for now.
I'll look at stock u-boot while it is running to see what else we can do.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
