Debian Stretch on Sata disk in WD MyCloud EX2 Ultra
Posted by LinAdmin
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 16, 2022 08:41AM |
Registered: 1 year ago Posts: 142 |
Ok, following our commands and envs before, the box is up, but...
Marvell>> setenv usbActive 0
Marvell>> setenv usbType 3
Marvell>> usb start
(Re)start USB...
USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Marvell>> setenv set_bootargs_debian "setenv bootargs console=ttyS0,115200 root=LABEL=rootfs mtdparts=pxa3xx_nand-0:5m(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) earlyprintk=serial"
Marvell>> setenv boot_debian_usb "ext2load usb 0:1 0x00800000 boot/uImage; ext2load usb 0:1 0x02100000 boot/uRamdisk; bootm 0x00800000 0x02100000"
Marvell>> setenv bootcmd "run set_bootargs_debian; run boot_debian_usb; reset"
Marvell>> setenv bootcmd "run set_bootargs_debian; run boot_debian_usb; reset"
Marvell>>
Marvell>> setenv boot_debian_usb "usbActive 0; usbType 3; usb start; sleep 5; ext2load usb 0:1 0x00800000 boot/uImage; ext2load usb 0:1 0x02100000 boot/uRamdisk; bootm 0x00800000 0x02100000"
Marvell>> setenv bootcmd "run set_bootargs_debian; run boot_debian_usb; reset"
Marvell>> boot
Unknown command 'usbActive' - try 'help'
Unknown command 'usbType' - try 'help'
(Re)start USB...
USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
5236595 bytes read in 576 ms (8.7 MiB/s)
9649885 bytes read in 735 ms (12.5 MiB/s)
## Booting image at 00800000 ...
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-5.13.8-mvebu-tld-1
Created: 2022-12-16 13:41:58 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5236531 Bytes = 5 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02100000 ...
Image Name: initramfs-5.13.8-mvebu-tld-1
Created: 2021-09-24 7:54:32 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9649821 Bytes = 9.2 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 5.13.8-mvebu-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 SMP PREEMPT Sat Aug 7 14:58:41 PDT 2021
[ 0.000000][ T0] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
[ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: WD MyCloud Ex2 Ultra
[ 0.000000][ T0] printk: bootconsole [earlycon0] enabled
[ 0.000000][ T0] Memory policy: Data cache writealloc
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000002fffffff]
[ 0.000000][ T0] HighMem [mem 0x0000000030000000-0x000000003fffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000][ T0] percpu: Embedded 21 pages/cpu s54668 r8192 d23156 u86016
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 260608
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs mtdparts=pxa3xx_nand-0:5m(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) earlyprintk=serial
[ 0.000000][ T0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000][ T0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 1011704K/1048576K available (11264K kernel code, 1483K rwdata, 3112K rodata, 1024K init, 325K bss, 36872K reserved, 0K cma-reserved, 262144K highmem)
[ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x404/0x78c with crng_init=0
[ 0.000000][ T0] trace event string verifier disabled
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x06070000 -> 0x16070000
[ 0.000000][ T0] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000][ T0] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000][ T0] L2C-310 D prefetch enabled, offset 1 lines
[ 0.000000][ T0] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000][ T0] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
[ 0.000000][ T0] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
[ 0.000001][ T0] sched_clock: 64 bits at 666MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.008682][ T0] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x999999d70a, max_idle_ns: 440795225152 ns
[ 0.020389][ T0] Switching to timer-based delay loop, resolution 1ns
[ 0.027194][ T0] Ignoring duplicate/late registration of read_current_timer delay
[ 0.034912][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.047023][ T0] Console: colour dummy device 80x30
[ 0.052169][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 1332.00 BogoMIPS (lpj=6660000)
[ 0.063441][ T0] pid_max: default: 32768 minimum: 301
[ 0.068863][ T0] LSM: Security Framework initializing
[ 0.074207][ T0] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.082192][ T0] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.091196][ T0] CPU: Testing write buffer coherency: ok
[ 0.096765][ T0] CPU0: Spectre v2: using BPIALL workaround
[ 0.102630][ T1] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.109441][ T1] Setting up static identity map for 0x100000 - 0x100060
[ 0.116388][ T1] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
[ 0.122336][ T1] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.129293][ T1] rcu: Hierarchical SRCU implementation.
[ 0.135292][ T1] smp: Bringing up secondary CPUs ...
[ 0.140920][ T1] Booting CPU 1
[ 0.144377][ T0] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.144386][ T0] CPU1: Spectre v2: using BPIALL workaround
[ 0.156532][ T1] smp: Brought up 1 node, 2 CPUs
[ 0.161332][ T1] SMP: Total of 2 processors activated (2664.00 BogoMIPS).
[ 0.168365][ T1] CPU: All CPU(s) started in SVC mode.
[ 0.174035][ T1] devtmpfs: initialized
[ 0.180836][ T1] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.189355][ T24] wait_for_initramfs() called before rootfs_initcalls
[ 0.189496][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.206472][ T1] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.236293][ T1] prandom32: self test passed (less than 6 bits correlated)
[ 0.243429][ T1] prandom: seed boundary self test passed
[ 0.250549][ T1] prandom: 100 self tests passed
[ 0.255334][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.262394][ T1] NET: Registered protocol family 16
[ 0.268263][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.276391][ T1] audit: initializing netlink subsys (disabled)
[ 0.282598][ T36] audit: type=2000 audit(0.250:1): state=initialized audit_enabled=0 res=1
[ 0.283779][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.291300][ T1] cpuidle: using governor ladder
[ 0.302786][ T1] cpuidle: using governor menu
[ 0.307548][ T1] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.316217][ T1] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.322871][ T1] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
[ 0.331654][ T1] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling
[ 0.547091][ T1] raid6: int32x8 gen() 243 MB/s
[ 0.717083][ T1] raid6: int32x8 xor() 166 MB/s
[ 0.887104][ T1] raid6: int32x4 gen() 280 MB/s
[ 1.057112][ T1] raid6: int32x4 xor() 180 MB/s
[ 1.227122][ T1] raid6: int32x2 gen() 448 MB/s
[ 1.397045][ T1] raid6: int32x2 xor() 258 MB/s
[ 1.567080][ T1] raid6: int32x1 gen() 498 MB/s
[ 1.737043][ T1] raid6: int32x1 xor() 197 MB/s
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 16, 2022 08:42AM |
Registered: 1 year ago Posts: 142 |
[ 1.741990][ T1] raid6: using algorithm int32x1 gen() 498 MB/s [ 1.748068][ T1] raid6: .... xor() 197 MB/s, rmw enabled [ 1.753619][ T1] raid6: using intx1 recovery algorithm [ 1.759773][ T1] vgaarb: loaded [ 1.763485][ T1] SCSI subsystem initialized [ 1.768252][ T1] usbcore: registered new interface driver usbfs [ 1.774453][ T1] usbcore: registered new interface driver hub [ 1.780489][ T1] usbcore: registered new device driver usb [ 1.786432][ T1] mc: Linux media interface: v0.10 [ 1.791433][ T1] videodev: Linux video capture interface: v2.00 [ 1.797687][ T1] pps_core: LinuxPPS API ver. 1 registered [ 1.803326][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 1.813140][ T1] PTP clock support registered [ 1.819214][ T1] clocksource: Switched to clocksource arm_global_timer [ 1.853393][ T1] VFS: Disk quotas dquot_6.6.0 [ 1.858064][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.873418][ T1] NET: Registered protocol family 2 [ 1.878571][ T1] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 1.891794][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.900946][ T1] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.909433][ T1] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.917309][ T1] TCP: Hash tables configured (established 8192 bind 8192) [ 1.924747][ T1] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 1.932899][ T1] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.940224][ T1] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.948076][ T1] NET: Registered protocol family 1 [ 1.953532][ T1] RPC: Registered named UNIX socket transport module. [ 1.960176][ T1] RPC: Registered udp transport module. [ 1.965555][ T1] RPC: Registered tcp transport module. [ 1.970972][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.978085][ T1] PCI: CLS 0 bytes, default 64 [ 1.982955][ T538] Trying to unpack rootfs image as initramfs... [ 1.989232][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 2.009367][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 2.416320][ T538] Freeing initrd memory: 9424K [ 2.645835][ T1] Initialise system trusted keyrings [ 2.651011][ T1] Key type blacklist registered [ 2.656038][ T1] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 2.663300][ T1] zbud: loaded [ 2.667428][ T1] NFS: Registering the id_resolver key type [ 2.673213][ T1] Key type id_resolver registered [ 2.678074][ T1] Key type id_legacy registered [ 2.682814][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.690225][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 2.698286][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 2.769880][ T1] xor: measuring software checksum speed [ 2.779911][ T1] arm4regs : 2172 MB/sec [ 2.790964][ T1] 8regs : 1637 MB/sec [ 2.801681][ T1] 32regs : 1733 MB/sec [ 2.806713][ T1] xor: using function: arm4regs (2172 MB/sec) [ 2.812628][ T1] async_tx: api initialized (async) [ 2.817663][ T1] Key type asymmetric registered [ 2.822443][ T1] Asymmetric key parser 'x509' registered [ 2.828075][ T1] bounce: pool size: 64 pages [ 2.832665][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 2.840802][ T1] io scheduler bfq registered [ 2.846805][ T1] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 2.855228][ T1] debugfs: Directory 'f1018100.gpio' with parent 'regmap' already present! [ 2.864156][ T1] debugfs: Directory 'f1018140.gpio' with parent 'regmap' already present! [ 2.873788][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 2.939844][ T1] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 2.949465][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 3.009775][ T1] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 3.085343][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 3.094588][ T1] printk: console [ttyS0] disabled [ 3.119670][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 31, base_baud = 12500000) is a 16550A [ 3.129340][ T1] printk: console [ttyS0] enabled [ 3.129340][ T1] printk: console [ttyS0] enabled [ 3.139144][ T1] printk: bootconsole [earlycon0] disabled [ 3.139144][ T1] printk: bootconsole [earlycon0] disabled [ 3.171752][ T1] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 32, base_baud = 12500000) is a 16550A [ 3.182921][ T1] ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator [ 3.191435][ T1] ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator [ 3.199716][ T1] ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator [ 3.208309][ T1] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 3.218121][ T1] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 3.228769][ T1] scsi host0: ahci-mvebu [ 3.233465][ T1] scsi host1: ahci-mvebu [ 3.237848][ T1] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 52 [ 3.246536][ T1] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 52 [ 3.256486][ T1] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xda [ 3.263598][ T1] nand: Macronix MX30LF2G18AC [ 3.268155][ T1] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 3.277045][ T1] Bad block table found at page 131008, version 0x01 [ 3.284277][ T1] Bad block table found at page 130944, version 0x01 [ 3.291186][ T1] nand_read_bbt: bad block at 0x000002020000 [ 3.297057][ T1] nand_read_bbt: bad block at 0x0000062e0000 [ 3.302934][ T1] nand_read_bbt: bad block at 0x00000bac0000 [ 3.308800][ T1] nand_read_bbt: bad block at 0x00000d300000 [ 3.314670][ T1] nand_read_bbt: bad block at 0x00000dc60000 [ 3.320570][ T1] 8 cmdlinepart partitions found on MTD device pxa3xx_nand-0 [ 3.327834][ T1] Creating 8 MTD partitions on "pxa3xx_nand-0": [ 3.333970][ T1] 0x000000000000-0x000000500000 : "u-boot" [ 3.340816][ T1] 0x000000500000-0x000000a00000 : "kernel" [ 3.347532][ T1] 0x000000a00000-0x000000f00000 : "uRamdisk" [ 3.354470][ T1] 0x000000f00000-0x00000c800000 : "image.cfs" [ 3.361879][ T1] 0x00000c800000-0x00000d700000 : "rescue_fw" [ 3.368920][ T1] 0x00000d700000-0x00000eb00000 : "config" [ 3.375705][ T1] 0x00000eb00000-0x00000f500000 : "reserve1" [ 3.382646][ T1] 0x00000f500000-0x00000ff00000 : "reserve2"
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 16, 2022 08:42AM |
Registered: 1 year ago Posts: 142 |
[ 3.390374][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 3.398954][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 3.410889][ T1] libphy: Fixed MDIO Bus: probed [ 3.417574][ T1] libphy: orion_mdio_bus: probed [ 3.432471][ T1] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled [ 3.445253][ T1] mvneta f1034000.ethernet eth0: Using random mac address 6a:74:54:ef:1b:9f [ 3.454371][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.461673][ T1] ehci-pci: EHCI PCI platform driver [ 3.466951][ T1] ehci-orion: EHCI orion driver [ 3.471870][ T1] orion-ehci f1058000.usb: EHCI Host Controller [ 3.478015][ T1] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 3.486431][ T1] orion-ehci f1058000.usb: irq 48, io mem 0xf1058000 [ 3.529226][ T1] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 3.536054][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 3.545085][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.553058][ T1] usb usb1: Product: EHCI Host Controller [ 3.558662][ T1] usb usb1: Manufacturer: Linux 5.13.8-mvebu-tld-1 ehci_hcd [ 3.565844][ T1] usb usb1: SerialNumber: f1058000.usb [ 3.571703][ T1] hub 1-0:1.0: USB hub found [ 3.576201][ T1] hub 1-0:1.0: 1 port detected [ 3.580667][ T1241] ata1: SATA link down (SStatus 0 SControl 300) [ 3.582294][ T1] usbcore: registered new interface driver usblp [ 3.587004][ T1246] ata2: SATA link down (SStatus 0 SControl 300) [ 3.593355][ T1] usbcore: registered new interface driver usb-storage [ 3.606500][ T1] mousedev: PS/2 mouse device common for all mice [ 3.614443][ T1] armada38x-rtc f10a3800.rtc: registered as rtc0 [ 3.620775][ T1] armada38x-rtc f10a3800.rtc: setting system clock to 2022-12-16T14:38:30 UTC (1671201510) [ 3.631145][ T1] i2c /dev entries driver [ 3.635551][ T1] mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recovery not supported [ 3.644522][ T1] mv64xxx_i2c f1011100.i2c: can't get pinctrl, bus recovery not supported [ 3.656229][ T1] orion_wdt: Initial timeout 171 sec [ 3.661918][ T1] device-mapper: uevent: version 1.0.3 [ 3.667431][ T1] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com [ 3.676813][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 3.684098][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 3.691459][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 3.698838][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 3.705673][ T1] device-mapper: raid: Loading target version 1.15.1 [ 3.715104][ T1] marvell-cesa f1090000.crypto: CESA device successfully registered [ 3.723368][ T1] hid: raw HID events driver (C) Jiri Kosina [ 3.729771][ T1] usbcore: registered new interface driver usbhid [ 3.736079][ T1] usbhid: USB HID core driver [ 3.741041][ T1] drop_monitor: Initializing network drop monitor service [ 3.748358][ T1] NET: Registered protocol family 10 [ 3.754300][ T1] Segment Routing with IPv6 [ 3.758687][ T1] RPL Segment Routing with IPv6 [ 3.763490][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.771329][ T1] NET: Registered protocol family 17 [ 3.776617][ T1] 8021q: 802.1Q VLAN Support v1.8 [ 3.781587][ T1] Key type dns_resolver registered [ 3.786689][ T1] ThumbEE CPU extension supported. [ 3.791698][ T1] Registering SWP/SWPB emulation handler [ 3.797601][ T1] registered taskstats version 1 [ 3.802478][ T1] Loading compiled-in X.509 certificates [ 3.808383][ T1] zswap: loaded using pool lzo/zbud [ 3.813735][ T1] Key type ._fscrypt registered [ 3.818473][ T1] Key type .fscrypt registered [ 3.823133][ T1] Key type fscrypt-provisioning registered [ 3.830072][ T1] Key type big_key registered [ 3.848466][ T1] Key type encrypted registered [ 3.856015][ T538] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 3.862127][ T538] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 3.870454][ T538] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 3.880497][ T538] xhci-hcd f10f0000.usb3: irq 54, io mem 0xf10f0000 [ 3.887220][ T538] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 3.896259][ T538] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.904258][ T538] usb usb2: Product: xHCI Host Controller [ 3.909873][ T538] usb usb2: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 3.917048][ T538] usb usb2: SerialNumber: f10f0000.usb3 [ 3.922899][ T538] hub 2-0:1.0: USB hub found [ 3.927398][ T538] hub 2-0:1.0: 1 port detected [ 3.932322][ T538] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 3.938373][ T538] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 [ 3.946647][ T538] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed [ 3.953809][ T538] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.962808][ T538] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.13 [ 3.971833][ T538] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.979817][ T538] usb usb3: Product: xHCI Host Controller [ 3.985423][ T538] usb usb3: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 3.992604][ T538] usb usb3: SerialNumber: f10f0000.usb3 [ 3.998380][ T538] hub 3-0:1.0: USB hub found [ 4.002900][ T538] hub 3-0:1.0: 1 port detected [ 4.008061][ T538] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 4.014132][ T538] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 4.022469][ T538] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 4.032593][ T538] xhci-hcd f10f8000.usb3: irq 55, io mem 0xf10f8000 [ 4.039321][ T538] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 4.048336][ T538] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.056307][ T538] usb usb4: Product: xHCI Host Controller [ 4.061921][ T538] usb usb4: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 4.069096][ T538] usb usb4: SerialNumber: f10f8000.usb3 [ 4.075057][ T538] hub 4-0:1.0: USB hub found [ 4.079579][ T538] hub 4-0:1.0: 1 port detected [ 4.084468][ T538] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 4.090532][ T538] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 [ 4.098773][ T538] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 16, 2022 08:43AM |
Registered: 1 year ago Posts: 142 |
[ 4.105970][ T538] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.114973][ T538] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.13 [ 4.123998][ T538] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.131978][ T538] usb usb5: Product: xHCI Host Controller [ 4.137583][ T538] usb usb5: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 4.144769][ T538] usb usb5: SerialNumber: f10f8000.usb3 [ 4.150612][ T538] hub 5-0:1.0: USB hub found [ 4.155107][ T538] hub 5-0:1.0: 1 port detected [ 4.160604][ T1] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 4.170716][ T1] Freeing unused kernel memory: 1024K [ 4.219249][ T1444] usb 2-1: new high-speed USB device number 2 using xhci-hcd [ 4.227116][ T1] Checked W+X mappings: passed, no W+X pages found [ 4.233554][ T1] Run /init as init process Loading, please wait... Starting version 247.3-6 [ 4.399810][ T1444] usb 2-1: New USB device found, idVendor=0781, idProduct=5567, bcdDevice= 1.00 [ 4.408764][ T1444] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.429286][ T1444] usb 2-1: Product: Cruzer Blade [ 4.434119][ T1444] usb 2-1: Manufacturer: SanDisk [ 4.438939][ T1444] usb 2-1: SerialNumber: 02002829090522215920 [ 4.459647][ T1444] usb-storage 2-1:1.0: USB Mass Storage device detected [ 4.494683][ T1444] scsi host2: usb-storage 2-1:1.0 [ 4.556911][ T1549] usbcore: registered new interface driver uas Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. [ 5.549666][ T538] scsi 2:0:0:0: Direct-Access SanDisk Cruzer Blade 1.00 PQ: 0 ANSI: 6 [ 5.563341][ T634] sd 2:0:0:0: [sda] 120176640 512-byte logical blocks: (61.5 GB/57.3 GiB) [ 5.580009][ T634] sd 2:0:0:0: [sda] Write Protect is off [ 5.585817][ T634] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 5.600351][ T634] sda: sda1 [ 5.631911][ C0] random: fast init done [ 5.640198][ T634] sd 2:0:0:0: [sda] Attached SCSI removable disk Begin: Will now check root file system ... fsck from util-linux 2.36.1 [/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1 rootfs: clean, 22102/3760128 files, 513209/15021824 blocks done. [ 6.068824][ T1578] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 6.218393][ T1578] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none. done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.96 booting Using makefile-style concurrent boot in runlevel S. Setting hostname to 'debian'...done. Starting hotplug events dispatcher: systemd-udevd. Synthesizing the initial hotplug events (subsystems)...done. Synthesizing the initial hotplug events (devices)...done. Waiting for /dev to be fully populated...[ 8.206335][ T1773] sd 2:0:0:0: Attached scsi generic sg0 type 0 done. Activating swap:. [ 9.096968][ T1908] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro. Quota mode: none. Will now check all file systems. Checking all file systems. LABEL=rootfs is mounted Done checking file systems. Log is being saved in /var/log/fsck/checkfs if that location is writable. Cleaning up temporary files...Cleaning /tmp...done. /tmp. Will now mount local filesystems:. Will now activate swapfile swap, if any:done. Checking minimum space in /tmp...done. Cleaning up temporary files.... [ 10.050117][ T2284] random: dd: uninitialized urandom read (512 bytes read) Starting Setting kernel variables: sysctl. Initializing random number generator... done. [ 10.650111][ T2324] mvneta f1034000.ethernet eth0: PHY [f1072004.mdio-mii:00] driver [Marvell 88E1510] (irq=POLL) [ 10.660837][ T2324] mvneta f1034000.ethernet eth0: configuring for phy/sgmii link mode Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/c2:90:9a:b0:fd:d6 Sending on LPF/eth0/c2:90:9a:b0:fd:d6 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6 [ 14.819648][ T2325] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 14.828429][ T2325] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 20 DHCPOFFER of 192.168.1.97 from 192.168.1.254 DHCPREQUEST for 192.168.1.97 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.1.97 from 192.168.1.254 bound to 192.168.1.97 -- renewal in 38387 seconds. done. Starting RPC port mapper daemon: rpcbind. Starting NFS common utilities: statd idmapd. Cleaning up temporary files.... INIT: Entering runlevel: 2 Using makefile-style concurrent boot in runlevel 2. Not starting NFS kernel daemon: no exports. ... (warning). Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 2474 (syslogd) . Starting periodic command scheduler: cron. Starting NTP server: ntpd. [ 21.006027][ T2541] random: dbus-daemon: uninitialized urandom read (12 bytes read) [ 21.040940][ T2541] random: dbus-daemon: uninitialized urandom read (12 bytes read) Starting system message bus: dbus. [ 21.266463][ C1] random: crng init done Starting OpenBSD Secure Shell server: sshdsshd: no hostkeys available -- exiting. failed! Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 2502 (klogd) . Running local boot scripts (/etc/rc.local) ssh-keygen: generating new host keys: RSA DSA ECDSA ED25519 Starting OpenBSD Secure Shell server: sshd . Cannot read environment, using default Cannot read default environment from file <13>Dec 16 06:39:07 root[2599]: Cannot read u-boot env ethaddr . Debian GNU/Linux 11 debian ttyS0 debian login:
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 16, 2022 08:45AM |
Registered: 1 year ago Posts: 142 |
root@debian:~# cat /proc/cmdline console=ttyS0,115200 root=LABEL=rootfs mtdparts=pxa3xx_nand-0:5m(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) earlyprintk=serial
root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 00500000 00020000 "u-boot" mtd1: 00500000 00020000 "kernel" mtd2: 00500000 00020000 "uRamdisk" mtd3: 0b900000 00020000 "image.cfs" mtd4: 00f00000 00020000 "rescue_fw" mtd5: 01400000 00020000 "config" mtd6: 00a00000 00020000 "reserve1" mtd7: 00a00000 00020000 "reserve2"
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 16, 2022 08:46AM |
Registered: 1 year ago Posts: 142 |
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 16, 2022 08:47AM |
Registered: 1 year ago Posts: 142 |
dmesg if helps;
root@debian:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.13.8-mvebu-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 SMP PREEMPT Sat Aug 7 14:58:41 PDT 2021 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: WD MyCloud Ex2 Ultra [ 0.000000] printk: bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000002fffffff] [ 0.000000] HighMem [mem 0x0000000030000000-0x000000003fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] Normal zone: 1536 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 21 pages/cpu s54668 r8192 d23156 u86016 [ 0.000000] pcpu-alloc: s54668 r8192 d23156 u86016 alloc=21*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs mtdparts=pxa3xx_nand-0:5m(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) earlyprintk=serial [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000] Memory: 1011704K/1048576K available (11264K kernel code, 1483K rwdata, 3112K rodata, 1024K init, 325K bss, 36872K reserved, 0K cma-reserved, 262144K highmem) [ 0.000000] random: get_random_u32 called from ____cache_alloc+0x404/0x78c with crng_init=0 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C: DT/platform modifies aux control register: 0x06070000 -> 0x16070000 [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 D prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001 [ 0.000001] sched_clock: 64 bits at 666MHz, resolution 1ns, wraps every 4398046511103ns [ 0.008682] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x999999d70a, max_idle_ns: 440795225152 ns [ 0.020389] Switching to timer-based delay loop, resolution 1ns [ 0.027194] Ignoring duplicate/late registration of read_current_timer delay [ 0.034912] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.047023] Console: colour dummy device 80x30 [ 0.052169] Calibrating delay loop (skipped), value calculated using timer frequency.. 1332.00 BogoMIPS (lpj=6660000) [ 0.063441] pid_max: default: 32768 minimum: 301 [ 0.068863] LSM: Security Framework initializing [ 0.074207] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.082192] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.091196] CPU: Testing write buffer coherency: ok [ 0.096765] CPU0: Spectre v2: using BPIALL workaround [ 0.102630] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.109441] Setting up static identity map for 0x100000 - 0x100060 [ 0.116388] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4 [ 0.122336] mvebu-pmsu: Initializing Power Management Service Unit [ 0.129293] rcu: Hierarchical SRCU implementation. [ 0.135292] smp: Bringing up secondary CPUs ... [ 0.140920] Booting CPU 1 [ 0.144377] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.144386] CPU1: Spectre v2: using BPIALL workaround [ 0.156532] smp: Brought up 1 node, 2 CPUs [ 0.161332] SMP: Total of 2 processors activated (2664.00 BogoMIPS). [ 0.168365] CPU: All CPU(s) started in SVC mode. [ 0.174035] devtmpfs: initialized [ 0.180836] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.189355] wait_for_initramfs() called before rootfs_initcalls [ 0.189496] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.206472] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.236293] prandom32: self test passed (less than 6 bits correlated) [ 0.243429] prandom: seed boundary self test passed [ 0.250549] prandom: 100 self tests passed [ 0.255334] pinctrl core: initialized pinctrl subsystem [ 0.262394] NET: Registered protocol family 16 [ 0.268263] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.276391] audit: initializing netlink subsys (disabled) [ 0.282598] audit: type=2000 audit(0.250:1): state=initialized audit_enabled=0 res=1 [ 0.283779] thermal_sys: Registered thermal governor 'step_wise' [ 0.291300] cpuidle: using governor ladder [ 0.302786] cpuidle: using governor menu [ 0.307548] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.316217] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.322871] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling [ 0.331654] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling [ 0.547091] raid6: int32x8 gen() 243 MB/s [ 0.717083] raid6: int32x8 xor() 166 MB/s [ 0.887104] raid6: int32x4 gen() 280 MB/s [ 1.057112] raid6: int32x4 xor() 180 MB/s [ 1.227122] raid6: int32x2 gen() 448 MB/s [ 1.397045] raid6: int32x2 xor() 258 MB/s [ 1.567080] raid6: int32x1 gen() 498 MB/s [ 1.737043] raid6: int32x1 xor() 197 MB/s [ 1.741990] raid6: using algorithm int32x1 gen() 498 MB/s [ 1.748068] raid6: .... xor() 197 MB/s, rmw enabled [ 1.753619] raid6: using intx1 recovery algorithm [ 1.759773] vgaarb: loaded [ 1.763485] SCSI subsystem initialized [ 1.768086] libata version 3.00 loaded. [ 1.768252] usbcore: registered new interface driver usbfs [ 1.774453] usbcore: registered new interface driver hub [ 1.780489] usbcore: registered new device driver usb [ 1.786432] mc: Linux media interface: v0.10 [ 1.791433] videodev: Linux video capture interface: v2.00 [ 1.797687] pps_core: LinuxPPS API ver. 1 registered [ 1.803326] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 1.813140] PTP clock support registered [ 1.819214] clocksource: Switched to clocksource arm_global_timer [ 1.853393] VFS: Disk quotas dquot_6.6.0 [ 1.858064] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.873418] NET: Registered protocol family 2 [ 1.878571] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 1.891794] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.900946] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.909433] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.917309] TCP: Hash tables configured (established 8192 bind 8192) [ 1.924747] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear)
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 16, 2022 08:47AM |
Registered: 1 year ago Posts: 142 |
[ 1.932899] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.940224] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.948076] NET: Registered protocol family 1 [ 1.953532] RPC: Registered named UNIX socket transport module. [ 1.960176] RPC: Registered udp transport module. [ 1.965555] RPC: Registered tcp transport module. [ 1.970972] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.978085] PCI: CLS 0 bytes, default 64 [ 1.982955] Trying to unpack rootfs image as initramfs... [ 1.989232] NetWinder Floating Point Emulator V0.97 (double precision) [ 2.009367] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 2.416320] Freeing initrd memory: 9424K [ 2.645835] Initialise system trusted keyrings [ 2.651011] Key type blacklist registered [ 2.656038] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 2.663300] zbud: loaded [ 2.667428] NFS: Registering the id_resolver key type [ 2.673213] Key type id_resolver registered [ 2.678074] Key type id_legacy registered [ 2.682814] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.690225] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 2.698286] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 2.769880] xor: measuring software checksum speed [ 2.779911] arm4regs : 2172 MB/sec [ 2.790964] 8regs : 1637 MB/sec [ 2.801681] 32regs : 1733 MB/sec [ 2.806713] xor: using function: arm4regs (2172 MB/sec) [ 2.812628] async_tx: api initialized (async) [ 2.817663] Key type asymmetric registered [ 2.822443] Asymmetric key parser 'x509' registered [ 2.828075] bounce: pool size: 64 pages [ 2.832665] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 2.840802] io scheduler bfq registered [ 2.846805] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 2.855228] debugfs: Directory 'f1018100.gpio' with parent 'regmap' already present! [ 2.864156] debugfs: Directory 'f1018140.gpio' with parent 'regmap' already present! [ 2.873788] mv_xor f1060800.xor: Marvell shared XOR driver [ 2.939844] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 2.949465] mv_xor f1060900.xor: Marvell shared XOR driver [ 3.009775] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 3.085343] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 3.094588] printk: console [ttyS0] disabled [ 3.119670] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 31, base_baud = 12500000) is a 16550A [ 3.129340] printk: console [ttyS0] enabled [ 3.139144] printk: bootconsole [earlycon0] disabled [ 3.171752] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 32, base_baud = 12500000) is a 16550A [ 3.182921] ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator [ 3.191435] ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator [ 3.199716] ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator [ 3.208309] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 3.218121] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 3.228769] scsi host0: ahci-mvebu [ 3.233465] scsi host1: ahci-mvebu [ 3.237848] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 52 [ 3.246536] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 52 [ 3.256486] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xda [ 3.263598] nand: Macronix MX30LF2G18AC [ 3.268155] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 3.277045] Bad block table found at page 131008, version 0x01 [ 3.284277] Bad block table found at page 130944, version 0x01 [ 3.291186] nand_read_bbt: bad block at 0x000002020000 [ 3.297057] nand_read_bbt: bad block at 0x0000062e0000 [ 3.302934] nand_read_bbt: bad block at 0x00000bac0000 [ 3.308800] nand_read_bbt: bad block at 0x00000d300000 [ 3.314670] nand_read_bbt: bad block at 0x00000dc60000 [ 3.320570] 8 cmdlinepart partitions found on MTD device pxa3xx_nand-0 [ 3.327834] Creating 8 MTD partitions on "pxa3xx_nand-0": [ 3.333970] 0x000000000000-0x000000500000 : "u-boot" [ 3.340816] 0x000000500000-0x000000a00000 : "kernel" [ 3.347532] 0x000000a00000-0x000000f00000 : "uRamdisk" [ 3.354470] 0x000000f00000-0x00000c800000 : "image.cfs" [ 3.361879] 0x00000c800000-0x00000d700000 : "rescue_fw" [ 3.368920] 0x00000d700000-0x00000eb00000 : "config" [ 3.375705] 0x00000eb00000-0x00000f500000 : "reserve1" [ 3.382646] 0x00000f500000-0x00000ff00000 : "reserve2" [ 3.390374] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 3.398954] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 3.410889] libphy: Fixed MDIO Bus: probed [ 3.417574] libphy: orion_mdio_bus: probed [ 3.432471] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled [ 3.445253] mvneta f1034000.ethernet eth0: Using random mac address 6a:74:54:ef:1b:9f [ 3.454371] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.461673] ehci-pci: EHCI PCI platform driver [ 3.466951] ehci-orion: EHCI orion driver [ 3.471870] orion-ehci f1058000.usb: EHCI Host Controller [ 3.478015] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 3.486431] orion-ehci f1058000.usb: irq 48, io mem 0xf1058000 [ 3.529226] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 3.536054] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 3.545085] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.553058] usb usb1: Product: EHCI Host Controller [ 3.558662] usb usb1: Manufacturer: Linux 5.13.8-mvebu-tld-1 ehci_hcd [ 3.565844] usb usb1: SerialNumber: f1058000.usb [ 3.571703] hub 1-0:1.0: USB hub found [ 3.576201] hub 1-0:1.0: 1 port detected
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 16, 2022 08:48AM |
Registered: 1 year ago Posts: 142 |
[ 3.580667] ata1: SATA link down (SStatus 0 SControl 300) [ 3.582294] usbcore: registered new interface driver usblp [ 3.587004] ata2: SATA link down (SStatus 0 SControl 300) [ 3.593355] usbcore: registered new interface driver usb-storage [ 3.606500] mousedev: PS/2 mouse device common for all mice [ 3.614443] armada38x-rtc f10a3800.rtc: registered as rtc0 [ 3.620775] armada38x-rtc f10a3800.rtc: setting system clock to 2022-12-16T14:38:30 UTC (1671201510) [ 3.631145] i2c /dev entries driver [ 3.635551] mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recovery not supported [ 3.644522] mv64xxx_i2c f1011100.i2c: can't get pinctrl, bus recovery not supported [ 3.656229] orion_wdt: Initial timeout 171 sec [ 3.661918] device-mapper: uevent: version 1.0.3 [ 3.667431] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com [ 3.676813] device-mapper: multipath round-robin: version 1.2.0 loaded [ 3.684098] device-mapper: multipath queue-length: version 0.2.0 loaded [ 3.691459] device-mapper: multipath service-time: version 0.3.0 loaded [ 3.698838] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 3.705673] device-mapper: raid: Loading target version 1.15.1 [ 3.715104] marvell-cesa f1090000.crypto: CESA device successfully registered [ 3.723368] hid: raw HID events driver (C) Jiri Kosina [ 3.729771] usbcore: registered new interface driver usbhid [ 3.736079] usbhid: USB HID core driver [ 3.741041] drop_monitor: Initializing network drop monitor service [ 3.748358] NET: Registered protocol family 10 [ 3.754300] Segment Routing with IPv6 [ 3.758687] RPL Segment Routing with IPv6 [ 3.763490] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.771329] NET: Registered protocol family 17 [ 3.776617] 8021q: 802.1Q VLAN Support v1.8 [ 3.781587] Key type dns_resolver registered [ 3.786689] ThumbEE CPU extension supported. [ 3.791698] Registering SWP/SWPB emulation handler [ 3.797601] registered taskstats version 1 [ 3.802478] Loading compiled-in X.509 certificates [ 3.808383] zswap: loaded using pool lzo/zbud [ 3.813735] Key type ._fscrypt registered [ 3.818473] Key type .fscrypt registered [ 3.823133] Key type fscrypt-provisioning registered [ 3.830072] Key type big_key registered [ 3.848466] Key type encrypted registered [ 3.856015] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 3.862127] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 3.870454] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 3.880497] xhci-hcd f10f0000.usb3: irq 54, io mem 0xf10f0000 [ 3.887220] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 3.896259] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.904258] usb usb2: Product: xHCI Host Controller [ 3.909873] usb usb2: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 3.917048] usb usb2: SerialNumber: f10f0000.usb3 [ 3.922899] hub 2-0:1.0: USB hub found [ 3.927398] hub 2-0:1.0: 1 port detected [ 3.932322] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 3.938373] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 [ 3.946647] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed [ 3.953809] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.962808] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.13 [ 3.971833] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.979817] usb usb3: Product: xHCI Host Controller [ 3.985423] usb usb3: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 3.992604] usb usb3: SerialNumber: f10f0000.usb3 [ 3.998380] hub 3-0:1.0: USB hub found [ 4.002900] hub 3-0:1.0: 1 port detected [ 4.008061] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 4.014132] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 4.022469] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 4.032593] xhci-hcd f10f8000.usb3: irq 55, io mem 0xf10f8000 [ 4.039321] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 4.048336] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.056307] usb usb4: Product: xHCI Host Controller [ 4.061921] usb usb4: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 4.069096] usb usb4: SerialNumber: f10f8000.usb3 [ 4.075057] hub 4-0:1.0: USB hub found [ 4.079579] hub 4-0:1.0: 1 port detected [ 4.084468] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 4.090532] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 [ 4.098773] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed [ 4.105970] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.114973] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.13 [ 4.123998] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.131978] usb usb5: Product: xHCI Host Controller [ 4.137583] usb usb5: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 4.144769] usb usb5: SerialNumber: f10f8000.usb3 [ 4.150612] hub 5-0:1.0: USB hub found [ 4.155107] hub 5-0:1.0: 1 port detected [ 4.160604] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 4.170716] Freeing unused kernel memory: 1024K [ 4.219249] usb 2-1: new high-speed USB device number 2 using xhci-hcd [ 4.227116] Checked W+X mappings: passed, no W+X pages found [ 4.233554] Run /init as init process [ 4.237937] with arguments: [ 4.237942] /init [ 4.237946] with environment: [ 4.237950] HOME=/ [ 4.237954] TERM=linux [ 4.399810] usb 2-1: New USB device found, idVendor=0781, idProduct=5567, bcdDevice= 1.00 [ 4.408764] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.429286] usb 2-1: Product: Cruzer Blade [ 4.434119] usb 2-1: Manufacturer: SanDisk [ 4.438939] usb 2-1: SerialNumber: 02002829090522215920 [ 4.459647] usb-storage 2-1:1.0: USB Mass Storage device detected [ 4.494683] scsi host2: usb-storage 2-1:1.0 [ 4.556911] usbcore: registered new interface driver uas [ 5.549666] scsi 2:0:0:0: Direct-Access SanDisk Cruzer Blade 1.00 PQ: 0 ANSI: 6 [ 5.563341] sd 2:0:0:0: [sda] 120176640 512-byte logical blocks: (61.5 GB/57.3 GiB) [ 5.580009] sd 2:0:0:0: [sda] Write Protect is off [ 5.585537] sd 2:0:0:0: [sda] Mode Sense: 43 00 00 00 [ 5.585817] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 5.600351] sda: sda1 [ 5.631911] random: fast init done [ 5.640198] sd 2:0:0:0: [sda] Attached SCSI removable disk [ 6.068824] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 6.218393] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none. [ 8.206335] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 9.096968] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro. Quota mode: none. [ 10.050117] random: dd: uninitialized urandom read (512 bytes read) [ 10.650111] mvneta f1034000.ethernet eth0: PHY [f1072004.mdio-mii:00] driver [Marvell 88E1510] (irq=POLL) [ 10.660837] mvneta f1034000.ethernet eth0: configuring for phy/sgmii link mode [ 14.819648] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 14.828429] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 21.006027] random: dbus-daemon: uninitialized urandom read (12 bytes read) [ 21.040940] random: dbus-daemon: uninitialized urandom read (12 bytes read) [ 21.266463] random: crng init done
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 16, 2022 10:58AM |
Registered: 1 year ago Posts: 142 |
New attempt, using the custom kernel and filesystem from this GitHub (customised for Ex2-Ultra) and new usb key
Marvell>> setenv usbActive 0
Marvell>> setenv usbType 3
Marvell>> usb start
(Re)start USB...
USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Marvell>> setenv set_bootargs_debian "setenv bootargs console=ttyS0,115200 root=LABEL=rootfs mtdparts=pxa3xx_nand-0:5m(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) earlyprintk=serial"
Marvell>> setenv boot_debian_usb "usb start; sleep 5; ext2load usb 0:1 0x00800000 boot/uImage; ext2load usb 0:1 0x02100000 boot/uRamdisk; bootm 0x00800000 0x02100000"
Marvell>> setenv bootcmd "run set_bootargs_debian; run boot_debian_usb; reset"
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 16, 2022 10:59AM |
Registered: 1 year ago Posts: 142 |
Marvell>> boot
(Re)start USB...
USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
4523065 bytes read in 453 ms (9.5 MiB/s)
4841674 bytes read in 467 ms (9.9 MiB/s)
## Booting image at 00800000 ...
## Booting kernel from Legacy Image at 00800000 ...
Image Name: WDMC-EX2-Ultra
Created: 2022-12-16 9:14:48 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4523001 Bytes = 4.3 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02100000 ...
Image Name: Custom initramfs
Created: 2022-12-16 9:47:09 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 4841610 Bytes = 4.6 MiB
Load Address: 00e00000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
DTB:0x004536F8 (0x00004D01)
C:0x000080E0-0x00458540->0x00E7FF00-0x012D0360
DTB:0x012CB518 (0x00004E36)
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Linux version 6.0.13 (root@virtsrv) (arm-none-eabi-gcc (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027], GNU ld (2.35.2-2+14+b2) 2.35.2) #1 SMP PREEMPT Fri Dec 16 09:50:45 CET 2022
CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
OF: fdt: Machine model: My Cloud Expert Series EX2 Ultra (BVBZ/Ranger Peak)
Memory policy: Data cache writealloc
Zone ranges:
Normal [mem 0x0000000000000000-0x000000002fffffff]
HighMem [mem 0x0000000030000000-0x000000003fffffff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x0000000000000000-0x000000003fffffff]
Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
percpu: Embedded 11 pages/cpu s16212 r8192 d20652 u45056
Built 1 zonelists, mobility grouping on. Total pages: 260416
Kernel command line: console=ttyS0,115200 root=LABEL=rootfs mtdparts=pxa3xx_nand-0:5m(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) earlyprintk=serial
Unknown kernel command line parameters "earlyprintk=serial", will be passed to user space.
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
mem auto-init: stack:off, heap alloc:off, heap free:off
Memory: 1019468K/1048576K available (8981K kernel code, 508K rwdata, 2352K rodata, 1024K init, 351K bss, 29108K reserved, 0K cma-reserved, 262144K highmem)
rcu: Preemptible hierarchical RCU implementation.
rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
Trampoline variant of Tasks RCU enabled.
Tracing variant of Tasks RCU enabled.
rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies.
rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
L2C: DT/platform modifies aux control register: 0x06070000 -> 0x16070000
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 D prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
rcu: srcu_init: Setting srcu_struct sizes based on contention.
sched_clock: 64 bits at 666MHz, resolution 1ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x999999d70a, max_idle_ns: 440795225152 ns
Switching to timer-based delay loop, resolution 1ns
Ignoring duplicate/late registration of read_current_timer delay
clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 1332.00 BogoMIPS (lpj=666000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
CPU: Testing write buffer coherency: ok
CPU0: Spectre v2: using BPIALL workaround
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
cblist_init_generic: Setting adjustable number of callback queues.
cblist_init_generic: Setting shift to 1 and lim to 1.
cblist_init_generic: Setting shift to 1 and lim to 1.
Setting up static identity map for 0x100000 - 0x100060
mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
mvebu-pmsu: Initializing Power Management Service Unit
rcu: Hierarchical SRCU implementation.
rcu: Max phase no-delay instances is 400.
smp: Bringing up secondary CPUs ...
Booting CPU 1
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
CPU1: Spectre v2: using BPIALL workaround
smp: Brought up 1 node, 2 CPUs
SMP: Total of 2 processors activated (2664.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
futex hash table entries: 512 (order: 3, 32768 bytes, linear)
pinctrl core: initialized pinctrl subsystem
NET: Registered PF_NETLINK/PF_ROUTE protocol family
DMA: preallocated 256 KiB pool for atomic coherent allocations
thermal_sys: Registered thermal governor 'step_wise'
mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling
cryptd: max_cpu_qlen set to 1000
raid6: neonx8 gen() 585 MB/s
raid6: neonx4 gen() 1677 MB/s
raid6: neonx2 gen() 2049 MB/s
raid6: neonx1 gen() 1705 MB/s
raid6: int32x8 gen() 243 MB/s
raid6: int32x4 gen() 276 MB/s
raid6: int32x2 gen() 442 MB/s
raid6: int32x1 gen() 493 MB/s
raid6: using algorithm neonx2 gen() 2049 MB/s
raid6: .... xor() 1310 MB/s, rmw enabled
raid6: using neon recovery algorithm
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
clocksource: Switched to clocksource arm_global_timer
VFS: Disk quotas dquot_6.6.0
VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
FS-Cache: Loaded
NET: Registered PF_INET protocol family
IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
TCP: Hash tables configured (established 8192 bind 8192)
MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear)
UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
NET: Registered PF_UNIX/PF_LOCAL protocol family
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NET: Registered PF_XDP protocol family
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
workingset: timestamp_bits=14 max_order=18 bucket_order=4
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
Key type cifs.idmap registered
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
xor: measuring software checksum speed
arm4regs : 2166 MB/sec
8regs : 1542 MB/sec
32regs : 1725 MB/sec
neon : 1596 MB/sec
xor: using function: arm4regs (2166 MB/sec)
async_tx: api initialized (async)
bounce: pool size: 64 pages
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
mv_xor f1060800.xor: Marvell shared XOR driver
mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
mv_xor f1060900.xor: Marvell shared XOR driver
mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
Freeing initrd memory: 4732K
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
printk: console [ttyS0] disabled
f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 38, base_baud = 12500000) is a 16550A
printk: console [ttyS0] enabled
f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 39, base_baud = 12500000) is a 16550A
brd: module loaded
loop: module loaded
ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator
ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator
nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xda
nand: Macronix MX30LF2G18AC
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
nand_read_bbt: bad block at 0x000002020000
nand_read_bbt: bad block at 0x0000062e0000
nand_read_bbt: bad block at 0x00000bac0000
nand_read_bbt: bad block at 0x00000d300000
nand_read_bbt: bad block at 0x00000dc60000
8 cmdlinepart partitions found on MTD device pxa3xx_nand-0
Creating 8 MTD partitions on "pxa3xx_nand-0":
0x000000000000-0x000000500000 : "u-boot"
0x000000500000-0x000000a00000 : "kernel"
0x000000a00000-0x000000f00000 : "uRamdisk"
0x000000f00000-0x00000c800000 : "image.cfs"
0x00000c800000-0x00000d700000 : "rescue_fw"
0x00000d700000-0x00000eb00000 : "config"
0x00000eb00000-0x00000f500000 : "reserve1"
0x00000f500000-0x00000ff00000 : "reserve2"
wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
hwmon hwmon0: temp1_input not attached to any thermal zone
mvneta f1034000.ethernet eth0: Using random mac address 6a:38:21:b3:f7:31
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-orion: EHCI orion driver
orion-ehci f1058000.usb: EHCI Host Controller
orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
orion-ehci f1058000.usb: irq 42, io mem 0xf1058000
orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.00
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 6.0.13 ehci_hcd
usb usb1: SerialNumber: f1058000.usb
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
xhci-hcd f10f0000.usb3: xHCI Host Controller
xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
xhci-hcd f10f0000.usb3: irq 43, io mem 0xf10f0000
xhci-hcd f10f0000.usb3: xHCI Host Controller
xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.00
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: xHCI Host Controller
usb usb2: Manufacturer: Linux 6.0.13 xhci-hcd
usb usb2: SerialNumber: f10f0000.usb3
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.00
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: xHCI Host Controller
usb usb3: Manufacturer: Linux 6.0.13 xhci-hcd
usb usb3: SerialNumber: f10f0000.usb3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
xhci-hcd f10f8000.usb3: xHCI Host Controller
xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
xhci-hcd f10f8000.usb3: irq 44, io mem 0xf10f8000
xhci-hcd f10f8000.usb3: xHCI Host Controller
xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed
usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.00
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: xHCI Host Controller
usb usb4: Manufacturer: Linux 6.0.13 xhci-hcd
usb usb4: SerialNumber: f10f8000.usb3
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
usb usb5: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.00
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: xHCI Host Controller
usb usb5: Manufacturer: Linux 6.0.13 xhci-hcd
usb usb5: SerialNumber: f10f8000.usb3
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 1 port detected
usbcore: registered new interface driver usb-storage
i2c_dev: i2c /dev entries driver
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com
device-mapper: dm-log-userspace: version 1.3.0 loaded
device-mapper: raid: Loading target version 1.15.1
ledtrig-cpu: registered to indicate activity on CPUs
marvell-cesa f1090000.crypto: CESA device successfully registered
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
NET: Registered PF_INET6 protocol family
Segment Routing with IPv6
In-situ OAM (IOAM) with IPv6
sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
NET: Registered PF_PACKET protocol family
Bridge firewalling registered
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
Registering SWP/SWPB emulation handler
Btrfs loaded, crc32c=crc32c-generic, debug=on, assert=on, ref-verify=on, zoned=no, fsverity=no
BTRFS: selftest: sectorsize: 4096 nodesize: 4096
BTRFS: selftest: running btrfs free space cache tests
BTRFS: selftest: running extent only tests
BTRFS: selftest: running bitmap only tests
BTRFS: selftest: running bitmap and extent tests
usb 2-1: new high-speed USB device number 2 using xhci-hcd
BTRFS: selftest: running space stealing from bitmap to extent tests
BTRFS: selftest: running bytes index tests
BTRFS: selftest: running extent buffer operation tests
BTRFS: selftest: running btrfs_split_item tests
BTRFS: selftest: running extent I/O tests
BTRFS: selftest: running find delalloc tests
usb 2-1: New USB device found, idVendor=154b, idProduct=005b, bcdDevice=11.00
usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-1: Product: USB 2.0 FD
usb 2-1: Manufacturer: PNY Technologies
usb 2-1: SerialNumber: AA00000000021013
usb-storage 2-1:1.0: USB Mass Storage device detected
scsi host0: usb-storage 2-1:1.0
BTRFS: selftest: running find_first_clear_extent_bit test
BTRFS: selftest: running extent buffer bitmap tests
BTRFS: selftest: running inode tests
BTRFS: selftest: running btrfs_get_extent tests
BTRFS: selftest: running hole first btrfs_get_extent test
BTRFS: selftest: running outstanding_extents tests
BTRFS: selftest: running qgroup tests
BTRFS: selftest: running qgroup add/remove tests
BTRFS: selftest: running qgroup multiple refs test
BTRFS: selftest: running free space tree tests
BTRFS: selftest: sectorsize: 4096 nodesize: 8192
BTRFS: selftest: running btrfs free space cache tests
BTRFS: selftest: running extent only tests
BTRFS: selftest: running bitmap only tests
BTRFS: selftest: running bitmap and extent tests
BTRFS: selftest: running space stealing from bitmap to extent tests
BTRFS: selftest: running bytes index tests
BTRFS: selftest: running extent buffer operation tests
BTRFS: selftest: running btrfs_split_item tests
BTRFS: selftest: running extent I/O tests
BTRFS: selftest: running find delalloc tests
BTRFS: selftest: running find_first_clear_extent_bit test
BTRFS: selftest: running extent buffer bitmap tests
BTRFS: selftest: running inode tests
BTRFS: selftest: running btrfs_get_extent tests
BTRFS: selftest: running hole first btrfs_get_extent test
BTRFS: selftest: running outstanding_extents tests
BTRFS: selftest: running qgroup tests
BTRFS: selftest: running qgroup add/remove tests
BTRFS: selftest: running qgroup multiple refs test
BTRFS: selftest: running free space tree tests
BTRFS: selftest: sectorsize: 4096 nodesize: 16384
BTRFS: selftest: running btrfs free space cache tests
BTRFS: selftest: running extent only tests
BTRFS: selftest: running bitmap only tests
BTRFS: selftest: running bitmap and extent tests
BTRFS: selftest: running space stealing from bitmap to extent tests
BTRFS: selftest: running bytes index tests
BTRFS: selftest: running extent buffer operation tests
BTRFS: selftest: running btrfs_split_item tests
BTRFS: selftest: running extent I/O tests
BTRFS: selftest: running find delalloc tests
scsi 0:0:0:0: Direct-Access PNY USB 2.0 FD 1100 PQ: 0 ANSI: 4
sd 0:0:0:0: [sda] 7975296 512-byte logical blocks: (4.08 GB/3.80 GiB)
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] No Caching mode page found
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI removable disk
BTRFS: selftest: running find_first_clear_extent_bit test
BTRFS: selftest: running extent buffer bitmap tests
BTRFS: selftest: running inode tests
BTRFS: selftest: running btrfs_get_extent tests
BTRFS: selftest: running hole first btrfs_get_extent test
BTRFS: selftest: running outstanding_extents tests
BTRFS: selftest: running qgroup tests
BTRFS: selftest: running qgroup add/remove tests
BTRFS: selftest: running qgroup multiple refs test
BTRFS: selftest: running free space tree tests
BTRFS: selftest: sectorsize: 4096 nodesize: 32768
BTRFS: selftest: running btrfs free space cache tests
BTRFS: selftest: running extent only tests
BTRFS: selftest: running bitmap only tests
BTRFS: selftest: running bitmap and extent tests
BTRFS: selftest: running space stealing from bitmap to extent tests
BTRFS: selftest: running bytes index tests
BTRFS: selftest: running extent buffer operation tests
BTRFS: selftest: running btrfs_split_item tests
BTRFS: selftest: running extent I/O tests
BTRFS: selftest: running find delalloc tests
BTRFS: selftest: running find_first_clear_extent_bit test
BTRFS: selftest: running extent buffer bitmap tests
BTRFS: selftest: running inode tests
BTRFS: selftest: running btrfs_get_extent tests
BTRFS: selftest: running hole first btrfs_get_extent test
BTRFS: selftest: running outstanding_extents tests
BTRFS: selftest: running qgroup tests
BTRFS: selftest: running qgroup add/remove tests
BTRFS: selftest: running qgroup multiple refs test
BTRFS: selftest: running free space tree tests
BTRFS: selftest: sectorsize: 4096 nodesize: 65536
BTRFS: selftest: running btrfs free space cache tests
BTRFS: selftest: running extent only tests
BTRFS: selftest: running bitmap only tests
BTRFS: selftest: running bitmap and extent tests
BTRFS: selftest: running space stealing from bitmap to extent tests
BTRFS: selftest: running bytes index tests
BTRFS: selftest: running extent buffer operation tests
BTRFS: selftest: running btrfs_split_item tests
BTRFS: selftest: running extent I/O tests
BTRFS: selftest: running find delalloc tests
BTRFS: selftest: running find_first_clear_extent_bit test
BTRFS: selftest: running extent buffer bitmap tests
BTRFS: selftest: running inode tests
BTRFS: selftest: running btrfs_get_extent tests
BTRFS: selftest: running hole first btrfs_get_extent test
BTRFS: selftest: running outstanding_extents tests
BTRFS: selftest: running qgroup tests
BTRFS: selftest: running qgroup add/remove tests
BTRFS: selftest: running qgroup multiple refs test
BTRFS: selftest: running free space tree tests
BTRFS: selftest: running extent_map tests
BTRFS: selftest: running rmap tests
ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator
ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator
ahci-mvebu f10a8000.sata: masking port_map 0x3 -> 0x3
ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
scsi host1: ahci-mvebu
scsi host2: ahci-mvebu
ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 47
ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 47
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
Freeing unused kernel image (initmem) memory: 1024K
Run /init as init process
ubi0: attaching mtd7
ubi0: scanning is finished
ubi0 warning: ubi_eba_init: cannot reserve enough PEBs for bad PEB handling, reserved 34, need 40
ubi0: attached mtd7 (name "reserve2", size 10 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 80, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 9/4, WL threshold: 4096, image sequence number: 76145449
ubi0: available PEBs: 0, total reserved PEBs: 80, PEBs reserved for bad PEB handling: 34
ubi0: background thread "ubi_bgt0d" started, PID 954
UBI device number 0, total 80 LEBs (10158080 bytes, 9.6 MiB), available 0 LEBs (0 bytes), LEB siUBIFS (ubi0:0): Mounting in unauthenticated mode
ze 126976 bytes UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 958
(124.0 KiB)
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "reserve2"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 4063232 bytes (3 MiB, 32 LEBs), max 42 LEBs, journal size 1015809 bytes (0 MiB, 6 LEBs)
UBIFS (ubi0:0): reserved for root: 191915 bytes (187 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w5/r0), UUID 39B69ACC-1A12-438B-B1DA-6A6DF9416BCF, small LPT model
UBIFS (ubi0:0): full atime support is enabled.
UBIFS (ubi0:0): un-mount UBI device 0
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" stops
ubi0: detaching mtd7
ubi0: mtd7 is detached
Temperature set OK
Scanning for Btrfs filesystems
mdadm: failed to get exclusive lock on mapfile
mdadm: No arrays found in config file or automatically
### Press any key to stop and run shell... (2)Trying to mount root filesystem using kernel options
EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: none.
systemd[1]: System time before build time, advancing clock.
systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified)
systemd[1]: Detected architecture arm.
Welcome to Debian GNU/Linux 11 (bullseye)!
systemd[1]: Set hostname to <wdnas>.
systemd[1]: Queued start job for default target Graphical Interface.
random: crng init done
systemd[1]: Created slice system-getty.slice.
[ OK ] Created slice system-getty.slice.
systemd[1]: Created slice system-modprobe.slice.
[ OK ] Created slice system-modprobe.slice.
systemd[1]: Created slice system-serial\x2dgetty.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
systemd[1]: Created slice User and Session Slice.
[ OK ] Created slice User and Session Slice.
systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Started Dispatch Password …ts to Console Directory Watch.
systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ OK ] Started Forward Password R…uests to Wall Directory Watch.
systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped.
systemd[1]: Reached target Local Encrypted Volumes.
[ OK ] Reached target Local Encrypted Volumes.
systemd[1]: Reached target Paths.
[ OK ] Reached target Paths.
systemd[1]: Reached target Remote File Systems.
[ OK ] Reached target Remote File Systems.
systemd[1]: Reached target Slices.
[ OK ] Reached target Slices.
systemd[1]: Reached target Swap.
[ OK ] Reached target Swap.
systemd[1]: Listening on Syslog Socket.
[ OK ] Listening on Syslog Socket.
systemd[1]: Listening on fsck to fsckd communication Socket.
[ OK ] Listening on fsck to fsckd communication Socket.
systemd[1]: Listening on initctl Compatibility Named Pipe.
[ OK ] Listening on initctl Compatibility Named Pipe.
systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
systemd[1]: Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket (/dev/log).
systemd[1]: Listening on Journal Socket.
[ OK ] Listening on Journal Socket.
systemd[1]: Listening on udev Control Socket.
[ OK ] Listening on udev Control Socket.
systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
systemd[1]: Condition check resulted in Huge Pages File System being skipped.
systemd[1]: Mounting POSIX Message Queue File System...
Mounting POSIX Message Queue File System...
systemd[1]: Mounting Kernel Debug File System...
Mounting Kernel Debug File System...
systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
systemd[1]: Starting Set the console keyboard layout...
Starting Set the console keyboard layout...
systemd[1]: Starting Create list of static device nodes for the current kernel...
Starting Create list of st…odes for the current kernel...
systemd[1]: Starting Load Kernel Module configfs...
Starting Load Kernel Module configfs...
systemd[1]: Starting Load Kernel Module drm...
Starting Load Kernel Module drm...
systemd[1]: Starting Load Kernel Module fuse...
Starting Load Kernel Module fuse...
systemd[1]: Started Nameserver information manager.
[ OK ] Started Nameserver information manafuse: init (API version 7.36)
ger.
systemd[1]: Reached target Network (Pre).
[ OK ] Reached target Network (Pre).
systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
systemd[1]: Starting File System Check on Root Device...
Starting File System Check on Root Device...
systemd[1]: Starting Journal Service...
Starting Journal Service...
systemd[1]: Starting Load Kernel Modules...
Starting Load Kernel Modules...
systemd[1]: Starting Coldplug All udev Devices...
Starting Coldplug All udev Devices...
systemd[1]: Mounted POSIX Message Queue File System.
[ OK ystemd[1]: Mounted Kernel Debug File System.
0m] Mounted POSIX Messasystemd[1]: Finished Create list of static device nodes for the current kernel.
ge Queue File System.
[ OK ] Msystemd[1]: modprobe@configfs.service: Succeeded.
ounted Kernel Debug Filsystemd[1]: Finished Load Kernel Module configfs.
e System.
[ OK ystemd[1]: modprobe@drm.service: Succeeded.
m] Finished ystemd[1]: Finished Load Kernel Module drm.
1;39mCreate list of st… nodes systemd[1]: modprobe@fuse.service: Succeeded.
for the current kernel.
[ OK ] Finished Load Kernel Module configfs.
[ OK ] Finishesystemd[1]: Finished Load Kernel Module fuse.
d Load Kernel Module drm.
[ OK ] Finished Load Kernel Module fuse.
systemd[1]: Finished Load Kernel Modules.
[ OK ] Finished Load Kernel Modules.
systemd[1]: Mounting FUSE Control File System...
Mountinsystemd[1]: Condition check resulted in Kernel Configuration File System being skipped.
g FUSE Control File System...
systemd[1]: Started File System Check Daemon to report status.
[ OK ] Started File System Check Daemon to report status.
systemd[1]: Starting Apply Kernel Variables...
Starting Apply Kernel Variables...
systemd[1]: Finished File System Check on Root Device.
[ OK ] Finished File System Check on Root Device.
systemd[1]: Mounted FUSE Control File System.
[ OK ] Mounted FUSE Control File System.
systemd[1]: Starting Remount Root and Kernel File Systems...
Starting Remount Root and Kernel File Systems...
systemd[1]: Finished Set the console keyboard layout.
[ OK ] Finished Set the console keyboard layout.
systemd[1]: Finished Apply Kernel Variables.
[ OK ] Finished Apply Kernel Variables.
EXT4-fs (sda1): re-mounted. Quota mode: none.
systemd[1]: Finished Remount Root and Kernel File Systems.
[ OK ] Finished Remount Root and Kernel File Systems.
systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
systemd[1]: Starting Load/Save Random Seed...
Starting Load/Save Random Seed...
systemd[1]: Starting Create System Users...
Starting Create System Users...
systemd[1]: Started Journal Service.
[ OK ] Started Journal Service.
Starting Flush Journal to Persistent Storage...
systemd-journald[1011]: Received client request to flush runtime journal.
[ OK ] Finished Load/Save Random Seed.
[ OK ] Finished Coldplug All udev Devices.
Starting Helper to synchronize boot up for ifupdown...
[ OK ] Finished Flush Journal to Persistent Storage.
[ OK ] Finished Create System Users.
Starting Create Static Device Nodes in /dev...
[ OK ] Finished Create Static Device Nodes in /dev.
[ OK ] Reached target Local File Systems (Pre).
[ OK ] Reached target Local File Systems.
Starting Armbian ZRAM config...
Starting Set console font and keymap...
Starting Create Volatile Files and Directories...
Starting Rule-based Manage…for Device Events and Files...
[ OK ] Finished Create Volatile Files and Directories.
Starting Network Time Synchronization...
Starting Update UTMP about System Boot/Shutdown...
[ OK ] Started Rule-based Manager for Device Events and Files.
[ OK ] Finished Update UTMP about System Boot/Shutdown.
zram: Added device: zram0
zram: Added device: zram1
zram: Added device: zram2
[ OK ] Started Network Time Synchronization.
[ OK ] Reached target System Time Set.
[ OK ] Reached target System Time Synchronized.
[ OK ] Found device /dev/ttyS0.
zram1: detected capacity change from 0 to 1025224
Adding 512608k swap on /dev/zram1. Priority:5 extents:1 across:512608k SS
zram0: detected capacity change from 0 to 102400
zram2: detected capacity change from 0 to 1025224
EXT4-fs (zram2): mounted filesystem without journal. Quota mode: none.
ext4 filesystem being mounted at /tmp supports timestamps until 2038 (0x7fffffff)
[ OK ] Finished Armbian ZRAM config.
[ OK ] Finished Helper to synchronize boot up for ifupdown.
Starting Armbian memory supported logging...
[ OK ] Started ifup for eth0.
Starting Raise network interfaces...
EXT4-fs (zram0): mounted filesystem without journal. Quota mode: none.
ext4 filesystem being mounted at /var/log supports timestamps until 2038 (0x7fffffff)
mvneta f1034000.ethernet eth0: PHY [f1072004.mdio-mii:00] driver [Marvell 88E1510] (irq=POLL)
mvneta f1034000.ethernet eth0: configuring for phy/sgmii link mode
mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[FAILED] Failed to start Set console font and keymap.
See 'systemctl status console-setup.service' for details.
[ OK ] Finished Armbian memory supported logging.
[ OK ] Reached target System Initialization.
[ OK ] Started Daily apt download activities.
[ OK ] Started Daily apt upgrade and clean activities.
[ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems.
[ OK ] Started Discard unused blocks once a week.
[ OK ] Started Daily rotation of log files.
[ OK ] Started Daily man-db regeneration.
[ OK ] Started Run system activit…ounting tool every 10 minutes.
[ OK ] Started Generate summary o…esterday's process accounting.
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Reached target Timers.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
[ OK ] Started Regular background program processing daemon.
[ OK ] Started D-Bus System Message Bus.
Starting Remove Stale Onli…t4 Metadata Check Snapshots...
Starting System Logging Service...
Starting Resets System Activity Logs...
Starting User Login Management...
[ OK ] Finished Raise network interfaces.
[ OK ] Reached target Network.
[ OK ] Reached target Network is Online.
Starting LSB: simple distributed compiler server...
Starting OpenBSD Secure Shell server...
Starting Permit User Sessions...
[ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots.
[ OK ] Finished Resets System Activity Logs.
[ OK ] Finished Permit User Sessions.
[ OK ] Started Getty on tty1.
[ OK ] Started Serial Getty on ttyS0.
[ OK ] Reached target Login Prompts.
[ OK ] Started System Logging Service.
[ OK ] Started LSB: simple distributed compiler server.
[ OK ] Started User Login Management.
[ OK ] Started OpenBSD Secure Shell server.
[ OK ] Reached target Multi-User System.
[ OK ] Reached target Graphical Interface.
Starting Update UTMP about System Runlevel Changes...
[ OK ] Finished Update UTMP about System Runlevel Changes.
Debian GNU/Linux 11 wdnas ttyS0
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 16, 2022 11:05AM |
Registered: 1 year ago Posts: 142 |
This time, everything but console-setup service has worked as expected, even the real Mac address and the leds. This custom uses the Armbian ZRAM, to avoid use swap, and to not use the usb for logging. I am not sure, but it write them to the usb (the storage device) when you turn off the board.
root@wdnas:~# cat /proc/cmdline console=ttyS0,115200 root=LABEL=rootfs mtdparts=pxa3xx_nand-0:5m(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) earlyprintk=serial root@wdnas:~# cat /proc/mtd dev: size erasesize name mtd0: 00500000 00020000 "u-boot" mtd1: 00500000 00020000 "kernel" mtd2: 00500000 00020000 "uRamdisk" mtd3: 0b900000 00020000 "image.cfs" mtd4: 00f00000 00020000 "rescue_fw" mtd5: 01400000 00020000 "config" mtd6: 00a00000 00020000 "reserve1" mtd7: 00a00000 00020000 "reserve2"
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 16, 2022 11:05AM |
Registered: 1 year ago Posts: 142 |
root@wdnas:~# mount /dev/sda1 on / type ext3 (rw,noatime,nodiratime,errors=remount-ro,commit=600) proc on /proc type proc (rw,relatime) sysfs on /sys type sysfs (rw,relatime) devtmpfs on /dev type devtmpfs (rw,nosuid,noexec,size=4096k,nr_inodes=65536,mode=755) tmpfs on /dev/shm type tmpfs (rw) devpts on /dev/pts type devpts (rw,relatime,gid=5,mode=620,ptmxmode=000) tmpfs on /run type tmpfs (rw,nosuid,nodev,size=205048k,nr_inodes=819200,mode=755) tmpfs on /run/lock type tmpfs (rw,nosuid,nodev,noexec,relatime,size=5120k) cgroup2 on /sys/fs/cgroup type cgroup2 (rw,nosuid,nodev,noexec,relatime,nsdelegate,memory_recursiveprot) bpf on /sys/fs/bpf type bpf (rw,nosuid,nodev,noexec,relatime,mode=700) debugfs on /sys/kernel/debug type debugfs (rw,nosuid,nodev,noexec,relatime) mqueue on /dev/mqueue type mqueue (rw,nosuid,nodev,noexec,relatime) fusectl on /sys/fs/fuse/connections type fusectl (rw,nosuid,nodev,noexec,relatime) /dev/zram2 on /tmp type ext4 (rw,nosuid,relatime,discard) /dev/sda1 on /var/log.hdd type ext3 (rw,noatime,nodiratime,errors=remount-ro,commit=600) /dev/zram0 on /var/log type ext4 (rw,relatime,discard)
root@wdnas:~# df -h Filesystem Size Used Avail Use% Mounted on /dev/sda1 3.7G 724M 2.8G 21% / devtmpfs 4.0M 0 4.0M 0% /dev tmpfs 501M 0 501M 0% /dev/shm tmpfs 201M 1.5M 199M 1% /run tmpfs 5.0M 0 5.0M 0% /run/lock /dev/zram2 485M 32K 450M 1% /tmp /dev/zram0 49M 17M 29M 38% /var/log
Edited 1 time(s). Last edit at 12/16/2022 11:06AM by i5Js.
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 16, 2022 12:55PM |
Registered: 1 year ago Posts: 142 |
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 16, 2022 05:18PM |
Admin Registered: 13 years ago Posts: 18,545 |
i5Js,
Man, you're spamming the forum :) I thought we're being spammed when I saw 22 new posts in this thread. There is no need to break the bootlog into multiple posts. You should either post the entire log in 1 post, or attach it to the post.
IIRC, the MAC address was working before with kernel 5.13.8-mvebu-tld-1?
Boot with kernel 5.13.8-mvebu-tld-1, login and
And please post the output of dmesg in this boot, so I can check the MAC address issue, if there is one.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Man, you're spamming the forum :) I thought we're being spammed when I saw 22 new posts in this thread. There is no need to break the bootlog into multiple posts. You should either post the entire log in 1 post, or attach it to the post.
Quote
The mac address is not right
The leds are wrong too. Just blinking in blue the power one.
IIRC, the MAC address was working before with kernel 5.13.8-mvebu-tld-1?
Boot with kernel 5.13.8-mvebu-tld-1, login and
ls -l /sys/class/leds/I'd expect to see 4 LEDs like in the DTS definitions:
sata1-red-led {
label = "wdmcex2u:hdd1:red";
gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "none";
};
sata2-red-led {
label = "wdmcex2u:hdd2:red";
gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "none";
};
sata1-blue-led {
label = "wdmcex2u:hdd1:blue";
gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
linux,default-trigger = "disk-activity";
};
sata2-blue-led {
label = "wdmcex2u:hdd2:blue";
gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
linux,default-trigger = "disk-activity";
};
And please post the output of dmesg in this boot, so I can check the MAC address issue, if there is one.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 16, 2022 05:38PM |
Registered: 1 year ago Posts: 142 |
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 16, 2022 06:38PM |
Admin Registered: 13 years ago Posts: 18,545 |
Please use pastebin, or attach the log to the post.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 17, 2022 01:34AM |
Registered: 1 year ago Posts: 142 |
New boot with your stuff:
Edited 1 time(s). Last edit at 12/17/2022 01:35AM by i5Js.
Marvell>> boot
(Re)start USB...
USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
5236595 bytes read in 458 ms (10.9 MiB/s)
9649885 bytes read in 606 ms (15.2 MiB/s)
## Booting image at 00800000 ...
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-5.13.8-mvebu-tld-1
Created: 2022-12-17 7:24:32 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5236531 Bytes = 5 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02100000 ...
Image Name: initramfs-5.13.8-mvebu-tld-1
Created: 2021-09-24 7:54:32 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9649821 Bytes = 9.2 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000][ T0] Booting Linux on physical CPU 0x0
[ 0.000000][ T0] Linux version 5.13.8-mvebu-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 SMP PREEMPT Sat Aug 7 14:58:41 PDT 2021
[ 0.000000][ T0] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
[ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000][ T0] OF: fdt: Machine model: WD MyCloud Ex2 Ultra
[ 0.000000][ T0] printk: bootconsole [earlycon0] enabled
[ 0.000000][ T0] Memory policy: Data cache writealloc
[ 0.000000][ T0] Zone ranges:
[ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000002fffffff]
[ 0.000000][ T0] HighMem [mem 0x0000000030000000-0x000000003fffffff]
[ 0.000000][ T0] Movable zone start for each node
[ 0.000000][ T0] Early memory node ranges
[ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000][ T0] percpu: Embedded 21 pages/cpu s54668 r8192 d23156 u86016
[ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 260608
[ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs mtdparts=pxa3xx_nand-0:5m(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) earlyprintk=serial
[ 0.000000][ T0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000][ T0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 0.000000][ T0] Memory: 1011704K/1048576K available (11264K kernel code, 1483K rwdata, 3112K rodata, 1024K init, 325K bss, 36872K reserved, 0K cma-reserved, 262144K highmem)
[ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x404/0x78c with crng_init=0
[ 0.000000][ T0] trace event string verifier disabled
[ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.000000][ T0] Tracing variant of Tasks RCU enabled.
[ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x06070000 -> 0x16070000
[ 0.000000][ T0] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000][ T0] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000][ T0] L2C-310 D prefetch enabled, offset 1 lines
[ 0.000000][ T0] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000][ T0] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
[ 0.000000][ T0] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
[ 0.000001][ T0] sched_clock: 64 bits at 666MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.008681][ T0] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x999999d70a, max_idle_ns: 440795225152 ns
[ 0.020388][ T0] Switching to timer-based delay loop, resolution 1ns
[ 0.027192][ T0] Ignoring duplicate/late registration of read_current_timer delay
[ 0.034909][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.047021][ T0] Console: colour dummy device 80x30
[ 0.052167][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 1332.00 BogoMIPS (lpj=6660000)
[ 0.063439][ T0] pid_max: default: 32768 minimum: 301
[ 0.068862][ T0] LSM: Security Framework initializing
[ 0.074206][ T0] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.082191][ T0] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.091192][ T0] CPU: Testing write buffer coherency: ok
[ 0.096761][ T0] CPU0: Spectre v2: using BPIALL workaround
[ 0.102625][ T1] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.109435][ T1] Setting up static identity map for 0x100000 - 0x100060
[ 0.116384][ T1] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
[ 0.122333][ T1] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.129290][ T1] rcu: Hierarchical SRCU implementation.
[ 0.135291][ T1] smp: Bringing up secondary CPUs ...
[ 0.140915][ T1] Booting CPU 1
[ 0.144373][ T0] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.144382][ T0] CPU1: Spectre v2: using BPIALL workaround
[ 0.156527][ T1] smp: Brought up 1 node, 2 CPUs
[ 0.161328][ T1] SMP: Total of 2 processors activated (2664.00 BogoMIPS).
[ 0.168362][ T1] CPU: All CPU(s) started in SVC mode.
[ 0.174036][ T1] devtmpfs: initialized
[ 0.180851][ T1] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.189372][ T24] wait_for_initramfs() called before rootfs_initcalls
[ 0.189513][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.206491][ T1] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.236307][ T1] prandom32: self test passed (less than 6 bits correlated)
[ 0.243442][ T1] prandom: seed boundary self test passed
[ 0.250562][ T1] prandom: 100 self tests passed
[ 0.255347][ T1] pinctrl core: initialized pinctrl subsystem
[ 0.262421][ T1] NET: Registered protocol family 16
[ 0.268290][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.276427][ T1] audit: initializing netlink subsys (disabled)
[ 0.282636][ T36] audit: type=2000 audit(0.250:1): state=initialized audit_enabled=0 res=1
[ 0.283817][ T1] thermal_sys: Registered thermal governor 'step_wise'
[ 0.291344][ T1] cpuidle: using governor ladder
[ 0.302826][ T1] cpuidle: using governor menu
[ 0.307589][ T1] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.316259][ T1] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.322914][ T1] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
[ 0.331698][ T1] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling
[ 0.547096][ T1] raid6: int32x8 gen() 243 MB/s
[ 0.717060][ T1] raid6: int32x8 xor() 166 MB/s
[ 0.887097][ T1] raid6: int32x4 gen() 280 MB/s
[ 1.057113][ T1] raid6: int32x4 xor() 180 MB/s
[ 1.227067][ T1] raid6: int32x2 gen() 447 MB/s
[ 1.397068][ T1] raid6: int32x2 xor() 262 MB/s
[ 1.567087][ T1] raid6: int32x1 gen() 498 MB/s
[ 1.737050][ T1] raid6: int32x1 xor() 185 MB/s
[ 1.741995][ T1] raid6: using algorithm int32x1 gen() 498 MB/s
[ 1.748074][ T1] raid6: .... xor() 185 MB/s, rmw enabled
[ 1.753625][ T1] raid6: using intx1 recovery algorithm
[ 1.759788][ T1] vgaarb: loaded
[ 1.763497][ T1] SCSI subsystem initialized
[ 1.768267][ T1] usbcore: registered new interface driver usbfs
[ 1.774473][ T1] usbcore: registered new interface driver hub
[ 1.780513][ T1] usbcore: registered new device driver usb
[ 1.786454][ T1] mc: Linux media interface: v0.10
[ 1.791458][ T1] videodev: Linux video capture interface: v2.00
[ 1.797714][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 1.803354][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.813169][ T1] PTP clock support registered
[ 1.819217][ T1] clocksource: Switched to clocksource arm_global_timer
[ 1.853538][ T1] VFS: Disk quotas dquot_6.6.0
[ 1.858208][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.873574][ T1] NET: Registered protocol family 2
[ 1.878730][ T1] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 1.892336][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 1.901495][ T1] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 1.909981][ T1] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 1.917857][ T1] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.925315][ T1] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear)
[ 1.933469][ T1] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 1.940793][ T1] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 1.948646][ T1] NET: Registered protocol family 1
[ 1.954104][ T1] RPC: Registered named UNIX socket transport module.
[ 1.960748][ T1] RPC: Registered udp transport module.
[ 1.966128][ T1] RPC: Registered tcp transport module.
[ 1.971545][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.978657][ T1] PCI: CLS 0 bytes, default 64
[ 1.983529][ T538] Trying to unpack rootfs image as initramfs...
[ 1.989626][ T1] NetWinder Floating Point Emulator V0.97 (double precision)
[ 2.009368][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
[ 2.386840][ T538] Freeing initrd memory: 9424K
[ 2.626577][ T1] Initialise system trusted keyrings
[ 2.631754][ T1] Key type blacklist registered
[ 2.636549][ T1] workingset: timestamp_bits=30 max_order=18 bucket_order=0
[ 2.643769][ T1] zbud: loaded
[ 2.647923][ T1] NFS: Registering the id_resolver key type
[ 2.653688][ T1] Key type id_resolver registered
[ 2.658549][ T1] Key type id_legacy registered
[ 2.663263][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 2.670646][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 2.678706][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 2.745374][ T1] xor: measuring software checksum speed
[ 2.755392][ T1] arm4regs : 2172 MB/sec
[ 2.766456][ T1] 8regs : 1637 MB/sec
[ 2.777181][ T1] 32regs : 1733 MB/sec
[ 2.782223][ T1] xor: using function: arm4regs (2172 MB/sec)
[ 2.788126][ T1] async_tx: api initialized (async)
[ 2.793170][ T1] Key type asymmetric registered
[ 2.797943][ T1] Asymmetric key parser 'x509' registered
[ 2.803584][ T1] bounce: pool size: 64 pages
[ 2.808224][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[ 2.816376][ T1] io scheduler bfq registered
[ 2.822950][ T1] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
[ 2.831643][ T1] debugfs: Directory 'f1018100.gpio' with parent 'regmap' already present!
[ 2.840754][ T1] debugfs: Directory 'f1018140.gpio' with parent 'regmap' already present!
[ 2.850541][ T1] mv_xor f1060800.xor: Marvell shared XOR driver
[ 2.909785][ T1] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 2.919556][ T1] mv_xor f1060900.xor: Marvell shared XOR driver
[ 2.979782][ T1] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 3.047049][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 3.056067][ T1] printk: console [ttyS0] disabled
[ 3.081191][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 31, base_baud = 12500000) is a 16550A
[ 3.090863][ T1] printk: console [ttyS0] enabled
[ 3.090863][ T1] printk: console [ttyS0] enabled
[ 3.100686][ T1] printk: bootconsole [earlycon0] disabled
[ 3.100686][ T1] printk: bootconsole [earlycon0] disabled
[ 3.133163][ T1] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 32, base_baud = 12500000) is a 16550A
[ 3.144316][ T1] ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator
[ 3.152818][ T1] ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator
[ 3.161115][ T1] ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator
[ 3.169714][ T1] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 3.179526][ T1] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 3.190156][ T1] scsi host0: ahci-mvebu
[ 3.194821][ T1] scsi host1: ahci-mvebu
[ 3.199260][ T1] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 52
[ 3.207930][ T1] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 52
[ 3.217796][ T1] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xda
[ 3.224910][ T1] nand: Macronix MX30LF2G18AC
[ 3.229500][ T1] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 3.238391][ T1] Bad block table found at page 131008, version 0x01
[ 3.245624][ T1] Bad block table found at page 130944, version 0x01
[ 3.252549][ T1] nand_read_bbt: bad block at 0x000002020000
[ 3.258420][ T1] nand_read_bbt: bad block at 0x0000062e0000
[ 3.264307][ T1] nand_read_bbt: bad block at 0x00000bac0000
[ 3.270198][ T1] nand_read_bbt: bad block at 0x00000d300000
[ 3.276065][ T1] nand_read_bbt: bad block at 0x00000dc60000
[ 3.281968][ T1] 8 cmdlinepart partitions found on MTD device pxa3xx_nand-0
[ 3.289259][ T1] Creating 8 MTD partitions on "pxa3xx_nand-0":
[ 3.295389][ T1] 0x000000000000-0x000000500000 : "u-boot"
[ 3.301998][ T1] 0x000000500000-0x000000a00000 : "kernel"
[ 3.308469][ T1] 0x000000a00000-0x000000f00000 : "uRamdisk"
[ 3.315111][ T1] 0x000000f00000-0x00000c800000 : "image.cfs"
[ 3.322278][ T1] 0x00000c800000-0x00000d700000 : "rescue_fw"
[ 3.329077][ T1] 0x00000d700000-0x00000eb00000 : "config"
[ 3.335601][ T1] 0x00000eb00000-0x00000f500000 : "reserve1"
[ 3.342301][ T1] 0x00000f500000-0x00000ff00000 : "reserve2"
[ 3.349521][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 3.358101][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 3.369170][ T1] libphy: Fixed MDIO Bus: probed
[ 3.374965][ T1] libphy: orion_mdio_bus: probed
[ 3.389531][ T1] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled
[ 3.401560][ T1] mvneta f1034000.ethernet eth0: Using random mac address 76:f9:77:1e:c2:0c
[ 3.410507][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.417793][ T1] ehci-pci: EHCI PCI platform driver
[ 3.423018][ T1] ehci-orion: EHCI orion driver
[ 3.427905][ T1] orion-ehci f1058000.usb: EHCI Host Controller
[ 3.434096][ T1] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[ 3.442546][ T1] orion-ehci f1058000.usb: irq 48, io mem 0xf1058000
[ 3.469226][ T1] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[ 3.476066][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13
[ 3.485117][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.493110][ T1] usb usb1: Product: EHCI Host Controller
[ 3.498734][ T1] usb usb1: Manufacturer: Linux 5.13.8-mvebu-tld-1 ehci_hcd
[ 3.505935][ T1] usb usb1: SerialNumber: f1058000.usb
[ 3.511695][ T1] hub 1-0:1.0: USB hub found
[ 3.516192][ T1] hub 1-0:1.0: 1 port detected
[ 3.521986][ T1] usbcore: registered new interface driver usblp
[ 3.528283][ T1] usbcore: registered new interface driver usb-storage
[ 3.535288][ T1] mousedev: PS/2 mouse device common for all mice
[ 3.541624][ T1245] ata2: SATA link down (SStatus 0 SControl 300)
[ 3.547783][ T1240] ata1: SATA link down (SStatus 0 SControl 300)
[ 3.548749][ T1] armada38x-rtc f10a3800.rtc: registered as rtc0
[ 3.560623][ T1] armada38x-rtc f10a3800.rtc: setting system clock to 2022-12-17T07:32:01 UTC (1671262321)
[ 3.570946][ T1] i2c /dev entries driver
[ 3.575361][ T1] mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recovery not supported
[ 3.584321][ T1] mv64xxx_i2c f1011100.i2c: can't get pinctrl, bus recovery not supported
[ 3.595996][ T1] orion_wdt: Initial timeout 171 sec
[ 3.601657][ T1] device-mapper: uevent: version 1.0.3
[ 3.607181][ T1] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com
[ 3.616583][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 3.623867][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 3.631225][ T1] device-mapper: multipath service-time: version 0.3.0 loaded
[ 3.638601][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 3.645435][ T1] device-mapper: raid: Loading target version 1.15.1
[ 3.654852][ T1] marvell-cesa f1090000.crypto: CESA device successfully registered
[ 3.663113][ T1] hid: raw HID events driver (C) Jiri Kosina
[ 3.669423][ T1] usbcore: registered new interface driver usbhid
[ 3.675733][ T1] usbhid: USB HID core driver
[ 3.680696][ T1] drop_monitor: Initializing network drop monitor service
[ 3.688011][ T1] NET: Registered protocol family 10
[ 3.693951][ T1] Segment Routing with IPv6
[ 3.698338][ T1] RPL Segment Routing with IPv6
[ 3.703141][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 3.710955][ T1] NET: Registered protocol family 17
[ 3.716247][ T1] 8021q: 802.1Q VLAN Support v1.8
[ 3.721204][ T1] Key type dns_resolver registered
[ 3.726306][ T1] ThumbEE CPU extension supported.
[ 3.731315][ T1] Registering SWP/SWPB emulation handler
[ 3.737210][ T1] registered taskstats version 1
[ 3.742077][ T1] Loading compiled-in X.509 certificates
[ 3.747989][ T1] zswap: loaded using pool lzo/zbud
[ 3.753326][ T1] Key type ._fscrypt registered
[ 3.758062][ T1] Key type .fscrypt registered
[ 3.762724][ T1] Key type fscrypt-provisioning registered
[ 3.769686][ T1] Key type big_key registered
[ 3.788024][ T1] Key type encrypted registered
[ 3.795571][ T23] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 3.801664][ T23] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
[ 3.809989][ T23] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
[ 3.820008][ T23] xhci-hcd f10f0000.usb3: irq 54, io mem 0xf10f0000
[ 3.826721][ T23] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13
[ 3.835751][ T23] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.843740][ T23] usb usb2: Product: xHCI Host Controller
[ 3.849354][ T23] usb usb2: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd
[ 3.856530][ T23] usb usb2: SerialNumber: f10f0000.usb3
[ 3.862350][ T23] hub 2-0:1.0: USB hub found
[ 3.866851][ T23] hub 2-0:1.0: 1 port detected
[ 3.871783][ T23] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 3.877833][ T23] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
[ 3.886092][ T23] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed
[ 3.893242][ T23] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.902237][ T23] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.13
[ 3.911265][ T23] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.919236][ T23] usb usb3: Product: xHCI Host Controller
[ 3.924841][ T23] usb usb3: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd
[ 3.932022][ T23] usb usb3: SerialNumber: f10f0000.usb3
[ 3.937794][ T23] hub 3-0:1.0: USB hub found
[ 3.942304][ T23] hub 3-0:1.0: 1 port detected
[ 3.947462][ T23] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 3.953562][ T23] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
[ 3.961885][ T23] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
[ 3.972006][ T23] xhci-hcd f10f8000.usb3: irq 55, io mem 0xf10f8000
[ 3.978700][ T23] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13
[ 3.987730][ T23] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.995702][ T23] usb usb4: Product: xHCI Host Controller
[ 4.001315][ T23] usb usb4: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd
[ 4.008490][ T23] usb usb4: SerialNumber: f10f8000.usb3
[ 4.014440][ T23] hub 4-0:1.0: USB hub found
[ 4.018938][ T23] hub 4-0:1.0: 1 port detected
[ 4.023856][ T23] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 4.029919][ T23] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
[ 4.038165][ T23] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed
[ 4.045317][ T23] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.054315][ T23] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.13
[ 4.063341][ T23] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.071311][ T23] usb usb5: Product: xHCI Host Controller
[ 4.076916][ T23] usb usb5: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd
[ 4.084102][ T23] usb usb5: SerialNumber: f10f8000.usb3
[ 4.089926][ T23] hub 5-0:1.0: USB hub found
[ 4.094421][ T23] hub 5-0:1.0: 1 port detected
[ 4.100063][ T1] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 4.110281][ T1] Freeing unused kernel memory: 1024K
[ 4.149786][ T1] Checked W+X mappings: passed, no W+X pages found
[ 4.156191][ T1] Run /init as init process
[ 4.169272][ T1443] usb 2-1: new high-speed USB device number 2 using xhci-hcd
Loading, please wait...
Starting version 247.3-6
[ 4.351762][ T1443] usb 2-1: New USB device found, idVendor=154b, idProduct=005b, bcdDevice=11.00
[ 4.370140][ T1443] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4.389997][ T1443] usb 2-1: Product: USB 2.0 FD
[ 4.395476][ T1443] usb 2-1: Manufacturer: PNY Technologies
[ 4.409263][ T1443] usb 2-1: SerialNumber: AA00000000021013
[ 4.429839][ T1443] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 4.450127][ T1443] scsi host2: usb-storage 2-1:1.0
[ 4.460424][ T1551] usbcore: registered new interface driver uas
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[ 5.615292][ T23] scsi 2:0:0:0: Direct-Access PNY USB 2.0 FD 1100 PQ: 0 ANSI: 4
[ 5.627220][ T23] sd 2:0:0:0: [sda] 7975296 512-byte logical blocks: (4.08 GB/3.80 GiB)
[ 5.635923][ T23] sd 2:0:0:0: [sda] Write Protect is off
[ 5.641899][ T23] sd 2:0:0:0: [sda] No Caching mode page found
[ 5.647946][ T23] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 5.657622][ T23] sda: sda1
[ 5.686214][ T23] sd 2:0:0:0: [sda] Attached SCSI removable disk
[ 5.718077][ C0] random: fast init done
Begin: Will now check root file system ... fsck from util-linux 2.36.1
[/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1
rootfs: clean, 22090/249488 files, 232358/996608 blocks
done.
[ 5.878728][ T1577] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 5.938838][ T1577] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.96 booting
Using makefile-style concurrent boot in runlevel S.
Setting hostname to 'debian'...done.
Starting hotplug events dispatcher: systemd-udevd.
Synthesizing the initial hotplug events (subsystems)...done.
Synthesizing the initial hotplug events (devices)...done.
Waiting for /dev to be fully populated...[ 7.645161][ T1765] sd 2:0:0:0: Attached scsi generic sg0 type 0
done.
Activating swap:.
[ 8.437225][ T1907] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro. Quota mode: none.
Will now check all file systems.
Checking all file systems.
LABEL=rootfs is mounted
Done checking file systems.
Log is being saved in /var/log/fsck/checkfs if that location is writable.
Cleaning up temporary files...Cleaning /tmp...done.
/tmp.
Will now mount local filesystems:.
Will now activate swapfile swap, if any:done.
Checking minimum space in /tmp...done.
Cleaning up temporary files....
[ 9.321405][ T2284] random: dd: uninitialized urandom read (512 bytes read)
Initializing random number generator...done.
Starting Setting kernel variables: sysctl.
[ 9.680105][ T2324] mvneta f1034000.ethernet eth0: PHY [f1072004.mdio-mii:00] driver [Marvell 88E1510] (irq=POLL)
[ 9.690810][ T2324] mvneta f1034000.ethernet eth0: configuring for phy/sgmii link mode
Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/eth0/c2:90:9a:b0:fd:d6
Sending on LPF/eth0/c2:90:9a:b0:fd:d6
Sending on Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
[ 13.859644][ T2325] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 13.868421][ T2325] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11
DHCPOFFER of 192.168.1.97 from 192.168.1.254
DHCPREQUEST for 192.168.1.97 on eth0 to 255.255.255.255 port 67
DHCPACK of 192.168.1.97 from 192.168.1.254
bound to 192.168.1.97 -- renewal in 33317 seconds.
done.
Starting RPC port mapper daemon: rpcbind.
Starting NFS common utilities: statd idmapd.
Cleaning up temporary files....
INIT: Entering runlevel: 2
Using makefile-style concurrent boot in runlevel 2.
Not starting NFS kernel daemon: no exports. ... (warning).
Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
2474 (syslogd)
.
[ 23.489678][ T2523] random: dbus-daemon: uninitialized urandom read (12 bytes read)
Starting periodic command schedu[ 23.532836][ T2523] random: dbus-daemon: uninitialized urandom read (12 bytes read)
ler: cron.
Starting NTP server: ntpd.
Starting system message bus: dbus.
[ 23.599809][ T2552] random: avahi-daemon: uninitialized urandom read (4 bytes read)
Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[ 24.759244][ C0] random: crng init done
[ 24.763376][ C0] random: 1 urandom warning(s) missed due to ratelimiting
Starting OpenBSD Secure Shell server: sshdsshd: no hostkeys available -- exiting.
failed!
Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
2516 (klogd)
.
Running local boot scripts (/etc/rc.local)
ssh-keygen: generating new host keys: RSA
DSA
ECDSA
ED25519
Starting OpenBSD Secure Shell server: sshd
.
Cannot read environment, using default
Cannot read default environment from file
<13>Dec 16 23:32:44 root[2599]: Cannot read u-boot env ethaddr
Edited 1 time(s). Last edit at 12/17/2022 01:35AM by i5Js.
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 17, 2022 01:40AM |
Registered: 1 year ago Posts: 142 |
I guess the leds issue is my fault, because there are no drives connected yet. I don't know why with the other kernel, the leds are on. Anyway, the output
About the MAC, look the latest lines
dmesg
root@debian:~# ls -l /sys/class/leds/ total 0 drwxr-xr-x 2 root root 0 Dec 16 23:32 . drwxr-xr-x 54 root root 0 Dec 16 23:32 .. lrwxrwxrwx 1 root root 0 Dec 16 23:35 wdmcex2u:hdd1:blue -> ../../devices/platform/gpio-leds/leds/wdmcex2u:hdd1:blue lrwxrwxrwx 1 root root 0 Dec 16 23:35 wdmcex2u:hdd1:red -> ../../devices/platform/gpio-leds/leds/wdmcex2u:hdd1:red lrwxrwxrwx 1 root root 0 Dec 16 23:35 wdmcex2u:hdd2:blue -> ../../devices/platform/gpio-leds/leds/wdmcex2u:hdd2:blue lrwxrwxrwx 1 root root 0 Dec 16 23:35 wdmcex2u:hdd2:red -> ../../devices/platform/gpio-leds/leds/wdmcex2u:hdd2:red
About the MAC, look the latest lines
Cannot read environment, using default Cannot read default environment from file <13>Dec 16 23:32:44 root[2599]: Cannot read u-boot env ethaddr
root@debian:~# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1024
link/ether c2:90:9a:b0:fd:d6 brd ff:ff:ff:ff:ff:ff. (It's wrong)
inet 192.168.1.97/24 brd 192.168.1.255 scope global dynamic eth0
valid_lft 86041sec preferred_lft 86041sec
inet6 fe80::c090:9aff:feb0:fdd6/64 scope link
valid_lft forever preferred_lft forever
3: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN group default qlen 1000
link/sit 0.0.0.0 brd 0.0.0.0
4: ip6tnl0@NONE: <NOARP> mtu 1452 qdisc noop state DOWN group default qlen 1000
link/tunnel6 :: brd :: permaddr aea3:f9dc:67c3::
dmesg
root@debian:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.13.8-mvebu-tld-1 (root@tldDebian) (gcc (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1.0 SMP PREEMPT Sat Aug 7 14:58:41 PDT 2021 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: WD MyCloud Ex2 Ultra [ 0.000000] printk: bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000002fffffff] [ 0.000000] HighMem [mem 0x0000000030000000-0x000000003fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] Normal zone: 1536 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 21 pages/cpu s54668 r8192 d23156 u86016 [ 0.000000] pcpu-alloc: s54668 r8192 d23156 u86016 alloc=21*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs mtdparts=pxa3xx_nand-0:5m(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) earlyprintk=serial [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000] Memory: 1011704K/1048576K available (11264K kernel code, 1483K rwdata, 3112K rodata, 1024K init, 325K bss, 36872K reserved, 0K cma-reserved, 262144K highmem) [ 0.000000] random: get_random_u32 called from ____cache_alloc+0x404/0x78c with crng_init=0 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C: DT/platform modifies aux control register: 0x06070000 -> 0x16070000 [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 D prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001 [ 0.000001] sched_clock: 64 bits at 666MHz, resolution 1ns, wraps every 4398046511103ns [ 0.008681] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x999999d70a, max_idle_ns: 440795225152 ns [ 0.020388] Switching to timer-based delay loop, resolution 1ns [ 0.027192] Ignoring duplicate/late registration of read_current_timer delay [ 0.034909] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.047021] Console: colour dummy device 80x30 [ 0.052167] Calibrating delay loop (skipped), value calculated using timer frequency.. 1332.00 BogoMIPS (lpj=6660000) [ 0.063439] pid_max: default: 32768 minimum: 301 [ 0.068862] LSM: Security Framework initializing [ 0.074206] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.082191] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.091192] CPU: Testing write buffer coherency: ok [ 0.096761] CPU0: Spectre v2: using BPIALL workaround [ 0.102625] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.109435] Setting up static identity map for 0x100000 - 0x100060 [ 0.116384] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4 [ 0.122333] mvebu-pmsu: Initializing Power Management Service Unit [ 0.129290] rcu: Hierarchical SRCU implementation. [ 0.135291] smp: Bringing up secondary CPUs ... [ 0.140915] Booting CPU 1 [ 0.144373] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.144382] CPU1: Spectre v2: using BPIALL workaround [ 0.156527] smp: Brought up 1 node, 2 CPUs [ 0.161328] SMP: Total of 2 processors activated (2664.00 BogoMIPS). [ 0.168362] CPU: All CPU(s) started in SVC mode. [ 0.174036] devtmpfs: initialized [ 0.180851] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.189372] wait_for_initramfs() called before rootfs_initcalls [ 0.189513] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.206491] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.236307] prandom32: self test passed (less than 6 bits correlated) [ 0.243442] prandom: seed boundary self test passed [ 0.250562] prandom: 100 self tests passed [ 0.255347] pinctrl core: initialized pinctrl subsystem [ 0.262421] NET: Registered protocol family 16 [ 0.268290] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.276427] audit: initializing netlink subsys (disabled) [ 0.282636] audit: type=2000 audit(0.250:1): state=initialized audit_enabled=0 res=1 [ 0.283817] thermal_sys: Registered thermal governor 'step_wise' [ 0.291344] cpuidle: using governor ladder [ 0.302826] cpuidle: using governor menu [ 0.307589] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.316259] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.322914] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling [ 0.331698] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling [ 0.547096] raid6: int32x8 gen() 243 MB/s [ 0.717060] raid6: int32x8 xor() 166 MB/s [ 0.887097] raid6: int32x4 gen() 280 MB/s [ 1.057113] raid6: int32x4 xor() 180 MB/s [ 1.227067] raid6: int32x2 gen() 447 MB/s [ 1.397068] raid6: int32x2 xor() 262 MB/s [ 1.567087] raid6: int32x1 gen() 498 MB/s [ 1.737050] raid6: int32x1 xor() 185 MB/s [ 1.741995] raid6: using algorithm int32x1 gen() 498 MB/s [ 1.748074] raid6: .... xor() 185 MB/s, rmw enabled [ 1.753625] raid6: using intx1 recovery algorithm [ 1.759788] vgaarb: loaded [ 1.763497] SCSI subsystem initialized [ 1.768100] libata version 3.00 loaded. [ 1.768267] usbcore: registered new interface driver usbfs [ 1.774473] usbcore: registered new interface driver hub [ 1.780513] usbcore: registered new device driver usb [ 1.786454] mc: Linux media interface: v0.10 [ 1.791458] videodev: Linux video capture interface: v2.00 [ 1.797714] pps_core: LinuxPPS API ver. 1 registered [ 1.803354] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 1.813169] PTP clock support registered [ 1.819217] clocksource: Switched to clocksource arm_global_timer [ 1.853538] VFS: Disk quotas dquot_6.6.0 [ 1.858208] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.873574] NET: Registered protocol family 2 [ 1.878730] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 1.892336] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.901495] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.909981] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.917857] TCP: Hash tables configured (established 8192 bind 8192) [ 1.925315] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 1.933469] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.940793] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.948646] NET: Registered protocol family 1 [ 1.954104] RPC: Registered named UNIX socket transport module. [ 1.960748] RPC: Registered udp transport module. [ 1.966128] RPC: Registered tcp transport module. [ 1.971545] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.978657] PCI: CLS 0 bytes, default 64 [ 1.983529] Trying to unpack rootfs image as initramfs... [ 1.989626] NetWinder Floating Point Emulator V0.97 (double precision) [ 2.009368] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 2.386840] Freeing initrd memory: 9424K [ 2.626577] Initialise system trusted keyrings [ 2.631754] Key type blacklist registered [ 2.636549] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 2.643769] zbud: loaded [ 2.647923] NFS: Registering the id_resolver key type [ 2.653688] Key type id_resolver registered [ 2.658549] Key type id_legacy registered [ 2.663263] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.670646] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 2.678706] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 2.745374] xor: measuring software checksum speed [ 2.755392] arm4regs : 2172 MB/sec [ 2.766456] 8regs : 1637 MB/sec [ 2.777181] 32regs : 1733 MB/sec [ 2.782223] xor: using function: arm4regs (2172 MB/sec) [ 2.788126] async_tx: api initialized (async) [ 2.793170] Key type asymmetric registered [ 2.797943] Asymmetric key parser 'x509' registered [ 2.803584] bounce: pool size: 64 pages [ 2.808224] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 2.816376] io scheduler bfq registered [ 2.822950] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 2.831643] debugfs: Directory 'f1018100.gpio' with parent 'regmap' already present! [ 2.840754] debugfs: Directory 'f1018140.gpio' with parent 'regmap' already present! [ 2.850541] mv_xor f1060800.xor: Marvell shared XOR driver [ 2.909785] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 2.919556] mv_xor f1060900.xor: Marvell shared XOR driver [ 2.979782] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 3.047049] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 3.056067] printk: console [ttyS0] disabled [ 3.081191] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 31, base_baud = 12500000) is a 16550A [ 3.090863] printk: console [ttyS0] enabled [ 3.100686] printk: bootconsole [earlycon0] disabled [ 3.133163] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 32, base_baud = 12500000) is a 16550A [ 3.144316] ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator [ 3.152818] ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator [ 3.161115] ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator [ 3.169714] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 3.179526] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 3.190156] scsi host0: ahci-mvebu [ 3.194821] scsi host1: ahci-mvebu [ 3.199260] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 52 [ 3.207930] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 52 [ 3.217796] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xda [ 3.224910] nand: Macronix MX30LF2G18AC [ 3.229500] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 3.238391] Bad block table found at page 131008, version 0x01 [ 3.245624] Bad block table found at page 130944, version 0x01 [ 3.252549] nand_read_bbt: bad block at 0x000002020000 [ 3.258420] nand_read_bbt: bad block at 0x0000062e0000 [ 3.264307] nand_read_bbt: bad block at 0x00000bac0000 [ 3.270198] nand_read_bbt: bad block at 0x00000d300000 [ 3.276065] nand_read_bbt: bad block at 0x00000dc60000 [ 3.281968] 8 cmdlinepart partitions found on MTD device pxa3xx_nand-0 [ 3.289259] Creating 8 MTD partitions on "pxa3xx_nand-0": [ 3.295389] 0x000000000000-0x000000500000 : "u-boot" [ 3.301998] 0x000000500000-0x000000a00000 : "kernel" [ 3.308469] 0x000000a00000-0x000000f00000 : "uRamdisk" [ 3.315111] 0x000000f00000-0x00000c800000 : "image.cfs" [ 3.322278] 0x00000c800000-0x00000d700000 : "rescue_fw" [ 3.329077] 0x00000d700000-0x00000eb00000 : "config" [ 3.335601] 0x00000eb00000-0x00000f500000 : "reserve1" [ 3.342301] 0x00000f500000-0x00000ff00000 : "reserve2" [ 3.349521] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 3.358101] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 3.369170] libphy: Fixed MDIO Bus: probed [ 3.374965] libphy: orion_mdio_bus: probed [ 3.389531] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled [ 3.401560] mvneta f1034000.ethernet eth0: Using random mac address 76:f9:77:1e:c2:0c [ 3.410507] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.417793] ehci-pci: EHCI PCI platform driver [ 3.423018] ehci-orion: EHCI orion driver [ 3.427905] orion-ehci f1058000.usb: EHCI Host Controller [ 3.434096] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 3.442546] orion-ehci f1058000.usb: irq 48, io mem 0xf1058000 [ 3.469226] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 3.476066] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 3.485117] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.493110] usb usb1: Product: EHCI Host Controller [ 3.498734] usb usb1: Manufacturer: Linux 5.13.8-mvebu-tld-1 ehci_hcd [ 3.505935] usb usb1: SerialNumber: f1058000.usb [ 3.511695] hub 1-0:1.0: USB hub found [ 3.516192] hub 1-0:1.0: 1 port detected [ 3.521986] usbcore: registered new interface driver usblp [ 3.528283] usbcore: registered new interface driver usb-storage [ 3.535288] mousedev: PS/2 mouse device common for all mice [ 3.541624] ata2: SATA link down (SStatus 0 SControl 300) [ 3.547783] ata1: SATA link down (SStatus 0 SControl 300) [ 3.548749] armada38x-rtc f10a3800.rtc: registered as rtc0 [ 3.560623] armada38x-rtc f10a3800.rtc: setting system clock to 2022-12-17T07:32:01 UTC (1671262321) [ 3.570946] i2c /dev entries driver [ 3.575361] mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recovery not supported [ 3.584321] mv64xxx_i2c f1011100.i2c: can't get pinctrl, bus recovery not supported [ 3.595996] orion_wdt: Initial timeout 171 sec [ 3.601657] device-mapper: uevent: version 1.0.3 [ 3.607181] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com [ 3.616583] device-mapper: multipath round-robin: version 1.2.0 loaded [ 3.623867] device-mapper: multipath queue-length: version 0.2.0 loaded [ 3.631225] device-mapper: multipath service-time: version 0.3.0 loaded [ 3.638601] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 3.645435] device-mapper: raid: Loading target version 1.15.1 [ 3.654852] marvell-cesa f1090000.crypto: CESA device successfully registered [ 3.663113] hid: raw HID events driver (C) Jiri Kosina [ 3.669423] usbcore: registered new interface driver usbhid [ 3.675733] usbhid: USB HID core driver [ 3.680696] drop_monitor: Initializing network drop monitor service [ 3.688011] NET: Registered protocol family 10 [ 3.693951] Segment Routing with IPv6 [ 3.698338] RPL Segment Routing with IPv6 [ 3.703141] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.710955] NET: Registered protocol family 17 [ 3.716247] 8021q: 802.1Q VLAN Support v1.8 [ 3.721204] Key type dns_resolver registered [ 3.726306] ThumbEE CPU extension supported. [ 3.731315] Registering SWP/SWPB emulation handler [ 3.737210] registered taskstats version 1 [ 3.742077] Loading compiled-in X.509 certificates [ 3.747989] zswap: loaded using pool lzo/zbud [ 3.753326] Key type ._fscrypt registered [ 3.758062] Key type .fscrypt registered [ 3.762724] Key type fscrypt-provisioning registered [ 3.769686] Key type big_key registered [ 3.788024] Key type encrypted registered [ 3.795571] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 3.801664] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 3.809989] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 3.820008] xhci-hcd f10f0000.usb3: irq 54, io mem 0xf10f0000 [ 3.826721] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 3.835751] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.843740] usb usb2: Product: xHCI Host Controller [ 3.849354] usb usb2: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 3.856530] usb usb2: SerialNumber: f10f0000.usb3 [ 3.862350] hub 2-0:1.0: USB hub found [ 3.866851] hub 2-0:1.0: 1 port detected [ 3.871783] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 3.877833] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 [ 3.886092] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed [ 3.893242] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.902237] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.13 [ 3.911265] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.919236] usb usb3: Product: xHCI Host Controller [ 3.924841] usb usb3: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 3.932022] usb usb3: SerialNumber: f10f0000.usb3 [ 3.937794] hub 3-0:1.0: USB hub found [ 3.942304] hub 3-0:1.0: 1 port detected [ 3.947462] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 3.953562] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 3.961885] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 3.972006] xhci-hcd f10f8000.usb3: irq 55, io mem 0xf10f8000 [ 3.978700] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13 [ 3.987730] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.995702] usb usb4: Product: xHCI Host Controller [ 4.001315] usb usb4: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 4.008490] usb usb4: SerialNumber: f10f8000.usb3 [ 4.014440] hub 4-0:1.0: USB hub found [ 4.018938] hub 4-0:1.0: 1 port detected [ 4.023856] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 4.029919] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 [ 4.038165] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed [ 4.045317] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.054315] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.13 [ 4.063341] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.071311] usb usb5: Product: xHCI Host Controller [ 4.076916] usb usb5: Manufacturer: Linux 5.13.8-mvebu-tld-1 xhci-hcd [ 4.084102] usb usb5: SerialNumber: f10f8000.usb3 [ 4.089926] hub 5-0:1.0: USB hub found [ 4.094421] hub 5-0:1.0: 1 port detected [ 4.100063] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 4.110281] Freeing unused kernel memory: 1024K [ 4.149786] Checked W+X mappings: passed, no W+X pages found [ 4.156191] Run /init as init process [ 4.160591] with arguments: [ 4.160597] /init [ 4.160601] with environment: [ 4.160605] HOME=/ [ 4.160608] TERM=linux [ 4.169272] usb 2-1: new high-speed USB device number 2 using xhci-hcd [ 4.351762] usb 2-1: New USB device found, idVendor=154b, idProduct=005b, bcdDevice=11.00 [ 4.370140] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.389997] usb 2-1: Product: USB 2.0 FD [ 4.395476] usb 2-1: Manufacturer: PNY Technologies [ 4.409263] usb 2-1: SerialNumber: AA00000000021013 [ 4.429839] usb-storage 2-1:1.0: USB Mass Storage device detected [ 4.450127] scsi host2: usb-storage 2-1:1.0 [ 4.460424] usbcore: registered new interface driver uas [ 5.615292] scsi 2:0:0:0: Direct-Access PNY USB 2.0 FD 1100 PQ: 0 ANSI: 4 [ 5.627220] sd 2:0:0:0: [sda] 7975296 512-byte logical blocks: (4.08 GB/3.80 GiB) [ 5.635923] sd 2:0:0:0: [sda] Write Protect is off [ 5.641463] sd 2:0:0:0: [sda] Mode Sense: 43 00 00 00 [ 5.641899] sd 2:0:0:0: [sda] No Caching mode page found [ 5.647946] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 5.657622] sda: sda1 [ 5.686214] sd 2:0:0:0: [sda] Attached SCSI removable disk [ 5.718077] random: fast init done [ 5.878728] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 5.938838] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null). Quota mode: none. [ 7.645161] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 8.437225] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro. Quota mode: none. [ 9.321405] random: dd: uninitialized urandom read (512 bytes read) [ 9.680105] mvneta f1034000.ethernet eth0: PHY [f1072004.mdio-mii:00] driver [Marvell 88E1510] (irq=POLL) [ 9.690810] mvneta f1034000.ethernet eth0: configuring for phy/sgmii link mode [ 13.859644] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 13.868421] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 23.489678] random: dbus-daemon: uninitialized urandom read (12 bytes read) [ 23.532836] random: dbus-daemon: uninitialized urandom read (12 bytes read) [ 23.599809] random: avahi-daemon: uninitialized urandom read (4 bytes read) [ 24.759244] random: crng init done [ 24.763376] random: 1 urandom warning(s) missed due to ratelimiting
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 17, 2022 02:00AM |
Registered: 1 year ago Posts: 142 |
I have updated to kernel 6, but not difference.
Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 6.0.7-mvebu-tld-1 (root@tldDebian) (gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1.0 SMP PREEMPT Tue Nov 8 16:49:35 PST 2022 [ 0.000000][ T0] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000][ T0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000][ T0] OF: fdt: Machine model: WD MyCloud Ex2 Ultra [ 0.000000][ T0] printk: bootconsole [earlycon0] enabled [ 0.000000][ T0] Memory policy: Data cache writealloc [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000002fffffff] [ 0.000000][ T0] HighMem [mem 0x0000000030000000-0x000000003fffffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000][ T0] percpu: Embedded 17 pages/cpu s38996 r8192 d22444 u69632 [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs mtdparts=pxa3xx_nand-0:5m(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) earlyprintk=serial [ 0.000000][ T0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 1009764K/1048576K available (10240K kernel code, 1513K rwdata, 3472K rodata, 1024K init, 470K bss, 38812K reserved, 0K cma-reserved, 262144K highmem) [ 0.000000][ T0] trace event string verifier disabled [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] L2C: DT/platform modifies aux control register: 0x06070000 -> 0x16070000 [ 0.000000][ T0] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000][ T0] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000][ T0] L2C-310 D prefetch enabled, offset 1 lines [ 0.000000][ T0] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000][ T0] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB [ 0.000000][ T0] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001 [ 0.000000][ T0] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000][ T0] kfence: initialized - using 2097152 bytes for 255 objects at 0x(ptrval)-0x(ptrval) [ 0.000000][ T0] sched_clock: 64 bits at 666MHz, resolution 1ns, wraps every 4398046511103ns [ 0.008678][ T0] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x999999d70a, max_idle_ns: 440795225152 ns [ 0.020385][ T0] Switching to timer-based delay loop, resolution 1ns [ 0.027199][ T0] Ignoring duplicate/late registration of read_current_timer delay [ 0.034916][ T0] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.047259][ T0] Console: colour dummy device 80x30 [ 0.052405][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 1332.00 BogoMIPS (lpj=6660000) [ 0.063678][ T0] pid_max: default: 32768 minimum: 301 [ 0.069186][ T0] LSM: Security Framework initializing [ 0.074628][ T0] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.082615][ T0] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.091692][ T0] CPU: Testing write buffer coherency: ok [ 0.097277][ T0] CPU0: Spectre v2: using BPIALL workaround [ 0.103209][ T1] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.110265][ T1] cblist_init_generic: Setting adjustable number of callback queues. [ 0.118179][ T1] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.125022][ T1] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.131889][ T1] Setting up static identity map for 0x100000 - 0x100060 [ 0.138862][ T1] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4 [ 0.144787][ T1] mvebu-pmsu: Initializing Power Management Service Unit [ 0.151784][ T1] rcu: Hierarchical SRCU implementation. [ 0.157267][ T1] rcu: Max phase no-delay instances is 1000. [ 0.163859][ T1] smp: Bringing up secondary CPUs ... [ 0.169627][ T1] Booting CPU 1 [ 0.173094][ T0] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.173105][ T0] CPU1: Spectre v2: using BPIALL workaround [ 0.185249][ T1] smp: Brought up 1 node, 2 CPUs [ 0.190051][ T1] SMP: Total of 2 processors activated (2664.00 BogoMIPS). [ 0.197084][ T1] CPU: All CPU(s) started in SVC mode. [ 0.202825][ T1] devtmpfs: initialized [ 0.210275][ T1] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.218912][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.229434][ T1] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.236986][ T1] prandom: seed boundary self test passed [ 0.244141][ T1] prandom: 100 self tests passed [ 0.248919][ T1] pinctrl core: initialized pinctrl subsystem [ 0.255728][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.263036][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.271265][ T1] audit: initializing netlink subsys (disabled) [ 0.277538][ T24] audit: type=2000 audit(0.250:1): state=initialized audit_enabled=0 res=1 [ 0.277900][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.286151][ T1] cpuidle: using governor ladder [ 0.297640][ T1] cpuidle: using governor menu [ 0.302359][ T1] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.311039][ T1] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.317695][ T1] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling [ 0.326451][ T1] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling [ 0.537196][ T1] raid6: int32x8 gen() 244 MB/s [ 0.707071][ T1] raid6: int32x4 gen() 262 MB/s [ 0.877074][ T1] raid6: int32x2 gen() 459 MB/s [ 1.047082][ T1] raid6: int32x1 gen() 532 MB/s [ 1.052030][ T1] raid6: using algorithm int32x1 gen() 532 MB/s [ 1.227083][ T1] raid6: .... xor() 205 MB/s, rmw enabled [ 1.232641][ T1] raid6: using intx1 recovery algorithm [ 1.238720][ T1] SCSI subsystem initialized [ 1.243449][ T1] usbcore: registered new interface driver usbfs [ 1.249674][ T1] usbcore: registered new interface driver hub [ 1.255684][ T1] usbcore: registered new device driver usb [ 1.261678][ T1] pps_core: LinuxPPS API ver. 1 registered [ 1.267328][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 1.277181][ T1] PTP clock support registered [ 1.282759][ T1] vgaarb: loaded [ 1.286541][ T1] clocksource: Switched to clocksource arm_global_timer [ 1.293840][ T1] VFS: Disk quotas dquot_6.6.0 [ 1.298568][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.313441][ T1] NET: Registered PF_INET protocol family [ 1.319225][ T1] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 1.328878][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 1.338070][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.346500][ T1] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.354984][ T1] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.362896][ T1] TCP: Hash tables configured (established 8192 bind 8192) [ 1.370162][ T1] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 1.378297][ T1] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.385603][ T1] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.393483][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.400348][ T1] RPC: Registered named UNIX socket transport module. [ 1.406984][ T1] RPC: Registered udp transport module. [ 1.412364][ T1] RPC: Registered tcp transport module. [ 1.417766][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.424878][ T1] PCI: CLS 0 bytes, default 64 [ 1.429595][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.429663][ T10] Trying to unpack rootfs image as initramfs... [ 1.442929][ T1] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 1.453083][ T1] Initialise system trusted keyrings [ 1.458302][ T1] Key type blacklist registered [ 1.463250][ T1] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 1.470603][ T1] zbud: loaded [ 1.475228][ T1] NFS: Registering the id_resolver key type [ 1.481141][ T1] Key type id_resolver registered [ 1.486010][ T1] Key type id_legacy registered [ 1.490774][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.498183][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.562083][ T1] xor: measuring software checksum speed [ 1.572124][ T1] arm4regs : 2172 MB/sec [ 1.583111][ T1] 8regs : 1668 MB/sec [ 1.593853][ T1] 32regs : 1733 MB/sec [ 1.598938][ T1] xor: using function: arm4regs (2172 MB/sec) [ 1.604852][ T1] async_tx: api initialized (async) [ 1.609917][ T1] Key type asymmetric registered [ 1.614697][ T1] Asymmetric key parser 'x509' registered [ 1.866319][ T10] Freeing initrd memory: 10200K [ 1.887695][ T1] alg: self-tests for CTR-KDF (hmac(sha256)) passed [ 1.894306][ T1] bounce: pool size: 64 pages [ 1.898960][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 1.907129][ T1] io scheduler bfq registered [ 1.914290][ T1] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 1.922979][ T1] debugfs: Directory 'f1018100.gpio' with parent 'regmap' already present! [ 1.932137][ T1] debugfs: Directory 'f1018140.gpio' with parent 'regmap' already present! [ 1.941499][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 2.017187][ T1] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 2.027335][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 2.087184][ T1] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 2.174224][ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 2.183577][ T1] printk: console [ttyS0] disabled [ 2.209122][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 39, base_baud = 12500000) is a 16550A [ 2.218808][ T1] printk: console [ttyS0] enabled [ 2.218808][ T1] printk: console [ttyS0] enabled [ 2.228630][ T1] printk: bootconsole [earlycon0] disabled [ 2.228630][ T1] printk: bootconsole [earlycon0] disabled [ 2.261186][ T1] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 40, base_baud = 12500000) is a 16550A [ 2.272871][ T1] ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator [ 2.281412][ T1] ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator [ 2.289717][ T1] ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator [ 2.298356][ T1] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 2.308169][ T1] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 2.319057][ T1] scsi host0: ahci-mvebu [ 2.323837][ T1] scsi host1: ahci-mvebu [ 2.328311][ T1] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 41 [ 2.336991][ T1] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 41 [ 2.346812][ T1] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xda [ 2.353910][ T1] nand: Macronix MX30LF2G18AC [ 2.358495][ T1] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 2.367154][ T1] Bad block table found at page 131008, version 0x01 [ 2.374037][ T1] Bad block table found at page 130944, version 0x01 [ 2.380791][ T1] nand_read_bbt: bad block at 0x000002020000 [ 2.386678][ T1] nand_read_bbt: bad block at 0x0000062e0000 [ 2.392550][ T1] nand_read_bbt: bad block at 0x00000bac0000 [ 2.398440][ T1] nand_read_bbt: bad block at 0x00000d300000 [ 2.404308][ T1] nand_read_bbt: bad block at 0x00000dc60000 [ 2.410220][ T1] 8 cmdlinepart partitions found on MTD device pxa3xx_nand-0 [ 2.417507][ T1] Creating 8 MTD partitions on "pxa3xx_nand-0": [ 2.423638][ T1] 0x000000000000-0x000000500000 : "u-boot" [ 2.430402][ T1] 0x000000500000-0x000000a00000 : "kernel" [ 2.437036][ T1] 0x000000a00000-0x000000f00000 : "uRamdisk" [ 2.443837][ T1] 0x000000f00000-0x00000c800000 : "image.cfs" [ 2.451114][ T1] 0x00000c800000-0x00000d700000 : "rescue_fw" [ 2.458031][ T1] 0x00000d700000-0x00000eb00000 : "config" [ 2.464679][ T1] 0x00000eb00000-0x00000f500000 : "reserve1" [ 2.471510][ T1] 0x00000f500000-0x00000ff00000 : "reserve2" [ 2.478959][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 2.487587][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 2.507981][ T1] hwmon hwmon0: temp1_input not attached to any thermal zone [ 2.516011][ T1] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled [ 2.529472][ T1] mvneta f1034000.ethernet eth0: Using random mac address 32:c8:0a:96:de:97 [ 2.538736][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.546025][ T1] ehci-pci: EHCI PCI platform driver [ 2.551330][ T1] ehci-orion: EHCI orion driver [ 2.556263][ T1] orion-ehci f1058000.usb: EHCI Host Controller [ 2.562457][ T1] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 2.570921][ T1] orion-ehci f1058000.usb: irq 44, io mem 0xf1058000 [ 2.606557][ T1] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 2.613468][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.00 [ 2.622521][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.630514][ T1] usb usb1: Product: EHCI Host Controller [ 2.636137][ T1] usb usb1: Manufacturer: Linux 6.0.7-mvebu-tld-1 ehci_hcd [ 2.643253][ T1] usb usb1: SerialNumber: f1058000.usb [ 2.649229][ T1] hub 1-0:1.0: USB hub found [ 2.653754][ T1] hub 1-0:1.0: 1 port detected [ 2.660112][ T1] usbcore: registered new interface driver usblp [ 2.666483][ T1] usbcore: registered new interface driver usb-storage [ 2.673707][ T1] mousedev: PS/2 mouse device common for all mice [ 2.680049][ T663] ata1: SATA link down (SStatus 0 SControl 300) [ 2.686215][ T668] ata2: SATA link down (SStatus 0 SControl 300) [ 2.692771][ T1] armada38x-rtc f10a3800.rtc: registered as rtc0 [ 2.699306][ T1] armada38x-rtc f10a3800.rtc: setting system clock to 2022-12-17T07:56:34 UTC (1671263794) [ 2.709978][ T1] i2c_dev: i2c /dev entries driver [ 2.715255][ T1] mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recovery not supported [ 2.724314][ T1] mv64xxx_i2c f1011100.i2c: can't get pinctrl, bus recovery not supported [ 2.736428][ T1] orion_wdt: Initial timeout 171 sec [ 2.742220][ T1] device-mapper: uevent: version 1.0.3 [ 2.747821][ T1] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 2.757263][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 2.764531][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 2.771901][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 2.779298][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 2.786125][ T1] device-mapper: raid: Loading target version 1.15.1 [ 2.795242][ T1] marvell-cesa f1090000.crypto: CESA device successfully registered [ 2.803576][ T1] hid: raw HID events driver (C) Jiri Kosina [ 2.809964][ T1] usbcore: registered new interface driver usbhid [ 2.816274][ T1] usbhid: USB HID core driver [ 2.821394][ T1] drop_monitor: Initializing network drop monitor service [ 2.828978][ T1] NET: Registered PF_INET6 protocol family [ 2.835699][ T1] Segment Routing with IPv6 [ 2.840107][ T1] RPL Segment Routing with IPv6 [ 2.844880][ T1] In-situ OAM (IOAM) with IPv6 [ 2.849592][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.857784][ T1] NET: Registered PF_PACKET protocol family [ 2.863708][ T1] 8021q: 802.1Q VLAN Support v1.8 [ 2.868698][ T1] Key type dns_resolver registered [ 2.873798][ T1] ThumbEE CPU extension supported. [ 2.878839][ T1] Registering SWP/SWPB emulation handler [ 2.884868][ T1] registered taskstats version 1 [ 2.889737][ T1] Loading compiled-in X.509 certificates [ 2.895763][ T1] zswap: loaded using pool lzo/zbud [ 2.901237][ T1] Key type ._fscrypt registered [ 2.905973][ T1] Key type .fscrypt registered [ 2.910633][ T1] Key type fscrypt-provisioning registered [ 2.917960][ T1] Key type big_key registered [ 2.936788][ T1] Key type encrypted registered [ 2.948233][ T10] usb_phy_generic usb3_0_phy: dummy supplies not allowed for exclusive requests [ 2.957401][ T10] usb_phy_generic usb3_1_phy: dummy supplies not allowed for exclusive requests [ 2.966650][ T10] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 2.972710][ T10] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 2.981031][ T10] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 2.991054][ T10] xhci-hcd f10f0000.usb3: irq 45, io mem 0xf10f0000 [ 2.997692][ T10] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 3.003755][ T10] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 [ 3.012007][ T10] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed [ 3.019251][ T10] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.00 [ 3.028280][ T10] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.036244][ T10] usb usb2: Product: xHCI Host Controller [ 3.041865][ T10] usb usb2: Manufacturer: Linux 6.0.7-mvebu-tld-1 xhci-hcd [ 3.048962][ T10] usb usb2: SerialNumber: f10f0000.usb3 [ 3.054888][ T10] hub 2-0:1.0: USB hub found [ 3.059407][ T10] hub 2-0:1.0: 1 port detected [ 3.064389][ T10] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.073420][ T10] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.00 [ 3.082457][ T10] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.090481][ T10] usb usb3: Product: xHCI Host Controller [ 3.096088][ T10] usb usb3: Manufacturer: Linux 6.0.7-mvebu-tld-1 xhci-hcd [ 3.103188][ T10] usb usb3: SerialNumber: f10f0000.usb3 [ 3.109045][ T10] hub 3-0:1.0: USB hub found [ 3.113540][ T10] hub 3-0:1.0: 1 port detected [ 3.118747][ T10] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 3.124807][ T10] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 3.133139][ T10] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 3.143160][ T10] xhci-hcd f10f8000.usb3: irq 46, io mem 0xf10f8000 [ 3.149854][ T10] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 3.155904][ T10] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 [ 3.164157][ T10] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed [ 3.171368][ T10] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.00 [ 3.180396][ T10] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.188367][ T10] usb usb4: Product: xHCI Host Controller [ 3.193972][ T10] usb usb4: Manufacturer: Linux 6.0.7-mvebu-tld-1 xhci-hcd [ 3.201127][ T10] usb usb4: SerialNumber: f10f8000.usb3 [ 3.207119][ T10] hub 4-0:1.0: USB hub found [ 3.211618][ T10] hub 4-0:1.0: 1 port detected [ 3.216609][ T10] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.225550][ T10] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.00 [ 3.234663][ T10] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.242733][ T10] usb usb5: Product: xHCI Host Controller [ 3.248433][ T10] usb usb5: Manufacturer: Linux 6.0.7-mvebu-tld-1 xhci-hcd [ 3.255524][ T10] usb usb5: SerialNumber: f10f8000.usb3 [ 3.261419][ T10] hub 5-0:1.0: USB hub found [ 3.265915][ T10] hub 5-0:1.0: 1 port detected [ 3.271768][ T1] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.282095][ T1] Freeing unused kernel image (initmem) memory: 1024K [ 3.327258][ T1] Checked W+X mappings: passed, no W+X pages found [ 3.333664][ T1] Run /init as init process [ 3.346642][ T35] usb 2-1: new high-speed USB device number 2 using xhci-hcd Loading, please wait... Starting version 247.3-6 [ 3.528208][ T35] usb 2-1: New USB device found, idVendor=154b, idProduct=005b, bcdDevice=11.00 [ 3.539716][ T35] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.547664][ T35] usb 2-1: Product: USB 2.0 FD [ 3.552315][ T35] usb 2-1: Manufacturer: PNY Technologies [ 3.558386][ T35] usb 2-1: SerialNumber: AA00000000021013 [ 3.571760][ T35] usb-storage 2-1:1.0: USB Mass Storage device detected [ 3.589205][ T35] scsi host2: usb-storage 2-1:1.0 [ 3.639510][ T1015] usbcore: registered new interface driver uas [ 3.892222][ T1011] mtdblock: MTD device 'u-boot' is NAND, please consider using UBI block devices instead. [ 3.899815][ T1018] mtdblock: MTD device 'kernel' is NAND, please consider using UBI block devices instead. [ 3.905077][ T1015] mtdblock: MTD device 'uRamdisk' is NAND, please consider using UBI block devices instead. [ 3.922744][ T1016] mtdblock: MTD device 'image.cfs' is NAND, please consider using UBI block devices instead. [ 3.926294][ T1012] mtdblock: MTD device 'config' is NAND, please consider using UBI block devices instead. [ 3.938027][ T1016] mtdblock: MTD device 'rescue_fw' is NAND, please consider using UBI block devices instead. [ 3.946421][ T1012] mtdblock: MTD device 'reserve1' is NAND, please consider using UBI block devices instead. [ 3.957498][ T1011] mtdblock: MTD device 'reserve2' is NAND, please consider using UBI block devices instead. Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. [ 4.299821][ T1032] mtdblock: MTD device 'u-boot' is NAND, please consider using UBI block devices instead. [ 4.321007][ T1032] mtdblock: MTD device 'kernel' is NAND, please consider using UBI block devices instead. [ 4.341946][ T1032] mtdblock: MTD device 'uRamdisk' is NAND, please consider using UBI block devices instead. [ 4.363123][ T1032] mtdblock: MTD device 'image.cfs' is NAND, please consider using UBI block devices instead. [ 4.466893][ T1032] mtdblock: MTD device 'rescue_fw' is NAND, please consider using UBI block devices instead. [ 4.506473][ T1032] mtdblock: MTD device 'config' is NAND, please consider using UBI block devices instead. [ 4.526174][ T1032] mtdblock: MTD device 'reserve1' is NAND, please consider using UBI block devices instead. [ 4.545901][ T1032] mtdblock: MTD device 'reserve2' is NAND, please consider using UBI block devices instead. [ 4.567108][ T1032] mtdblock: MTD device 'u-boot' is NAND, please consider using UBI block devices instead. [ 4.588103][ T1032] mtdblock: MTD device 'kernel' is NAND, please consider using UBI block devices instead. [ 4.609012][ T1032] mtdblock: MTD device 'uRamdisk' is NAND, please consider using UBI block devices instead. [ 4.630082][ T1032] mtdblock: MTD device 'image.cfs' is NAND, please consider using UBI block devices instead. [ 4.732995][ T1032] mtdblock: MTD device 'rescue_fw' is NAND, please consider using UBI block devices instead. Begin: Waiting for root file system ... [ 4.825679][ T8] scsi 2:0:0:0: Direct-Access PNY USB 2.0 FD 1100 PQ: 0 ANSI: 4 [ 4.835928][ T10] sd 2:0:0:0: [sda] 7975296 512-byte logical blocks: (4.08 GB/3.80 GiB) [ 4.845030][ T10] sd 2:0:0:0: [sda] Write Protect is off [ 4.851009][ T10] sd 2:0:0:0: [sda] No Caching mode page found [ 4.857087][ T10] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 4.866662][ T10] sda: sda1 [ 4.870016][ T10] sd 2:0:0:0: [sda] Attached SCSI removable disk Begin: Running /scripts/local-block ... done. done. Begin: Will now check root file system ... fsck from util-linux 2.36.1 [/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1 rootfs: recovering journal rootfs: clean, 25183/249488 files, 302669/996608 blocks done. [ 34.956850][ T1050] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 38.606570][ C0] random: crng init done [ 39.105224][ T1050] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: none. done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.96 booting Using makefile-style concurrent boot in runlevel S. Setting hostname to 'debian'...done. Starting hotplug events dispatcher: systemd-udevd. Synthesizing the initial hotplug events (subsystems)...done. Synthesizing the initial hotplug events (devices)...done. Waiting for /dev to be fully populated...[ 40.706129][ T1236] mtdblock: MTD device 'u-boot' is NAND, please consider using UBI block devices instead. [ 40.716361][ T1238] mtdblock: MTD device 'kernel' is NAND, please consider using UBI block devices instead. [ 40.723470][ T1239] mtdblock: MTD device 'image.cfs' is NAND, please consider using UBI block devices instead. [ 40.726359][ T1237] mtdblock: MTD device 'uRamdisk' is NAND, please consider using UBI block devices instead. [ 40.753429][ T1235] mtdblock: MTD device 'rescue_fw' is NAND, please consider using UBI block devices instead. [ 40.780338][ T1243] mtdblock: MTD device 'config' is NAND, please consider using UBI block devices instead. [ 40.786708][ T1235] mtdblock: MTD device 'reserve1' is NAND, please consider using UBI block devices instead. [ 40.802837][ T1236] mtdblock: MTD device 'reserve2' is NAND, please consider using UBI block devices instead. [ 40.919942][ T1239] sd 2:0:0:0: Attached scsi generic sg0 type 0 done. Activating swap:. [ 42.160315][ T1379] EXT4-fs (sda1): re-mounted. Quota mode: none. Will now check all file systems. Checking all file systems. LABEL=rootfs is mounted Done checking file systems. Log is being saved in /var/log/fsck/checkfs if that location is writable. Cleaning up temporary files...Cleaning /tmp...done. /tmp. Will now mount local filesystems:. Will now activate swapfile swap, if any:done. Checking minimum space in /tmp...done. Cleaning up temporary files.... Initializing random number generator...done. Starting Setting kernel variables: sysctl. [ 43.417550][ T1796] mvneta f1034000.ethernet eth0: PHY [f1072004.mdio-mii:00] driver [Marvell 88E1510] (irq=POLL) [ 43.429169][ T1796] mvneta f1034000.ethernet eth0: configuring for phy/sgmii link mode Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/c2:90:9a:b0:fd:d6 Sending on LPF/eth0/c2:90:9a:b0:fd:d6 Sending on Socket/fallback DHCPREQUEST for 192.168.1.97 on eth0 to 255.255.255.255 port 67 [ 47.626987][ T976] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 47.635767][ T976] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready DHCPREQUEST for 192.168.1.97 on eth0 to 255.255.255.255 port 67 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6 DHCPOFFER of 192.168.1.97 from 192.168.1.254 DHCPREQUEST for 192.168.1.97 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.1.97 from 192.168.1.254 bound to 192.168.1.97 -- renewal in 35745 seconds. done. Starting RPC port mapper daemon: rpcbind. Starting NFS common utilities: statd idmapd. Cleaning up temporary files.... INIT: Entering runlevel: 2 Using makefile-style concurrent boot in runlevel 2. Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1949 (syslogd) . Not starting NFS kernel daemon: no exports. ... (warning). Starting periodic command scheduler: cron. Starting NTP server: ntpd. Starting system message bus: dbus. Starting OpenBSD Secure Shell server: sshd. Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1990 (klogd) . Running local boot scripts (/etc/rc.local) Cannot read environment, using default Cannot read default environment from file <13>Dec 16 23:57:42 root[2067]: Cannot read u-boot env ethaddr . Debian GNU/Linux 11 debian ttyS0 debian login: root Password: Linux debian 6.0.7-mvebu-tld-1 #1.0 SMP PREEMPT Tue Nov 8 16:49:35 PST 2022 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. Last login: Fri Dec 16 23:33:19 PST 2022 on ttyS0 debian 192.168.1.97 WD MyCloud Ex2 Ultra Linux version 6.0.7-mvebu-tld-1 (root@tldDebian) (gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1.0 SMP PREEMPT Tue Nov 8 16:49:35 PST 2022 Debian 11.0 Fri Dec 16 23:57:53 PST 2022 up 1 minute root@debian:~# ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1024 link/ether c2:90:9a:b0:fd:d6 brd ff:ff:ff:ff:ff:ff inet 192.168.1.97/24 brd 192.168.1.255 scope global dynamic eth0 valid_lft 86382sec preferred_lft 86382sec inet6 fe80::c090:9aff:feb0:fdd6/64 scope link valid_lft forever preferred_lft forever 3: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN group default qlen 1000 link/sit 0.0.0.0 brd 0.0.0.0 4: ip6tnl0@NONE: <NOARP> mtu 1452 qdisc noop state DOWN group default qlen 1000 link/tunnel6 :: brd :: permaddr 3e50:bcf0:87ed:: root@debian:~#
root@debian:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.0.7-mvebu-tld-1 (root@tldDebian) (gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1.0 SMP PREEMPT Tue Nov 8 16:49:35 PST 2022 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: WD MyCloud Ex2 Ultra [ 0.000000] printk: bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000002fffffff] [ 0.000000] HighMem [mem 0x0000000030000000-0x000000003fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff] [ 0.000000] percpu: Embedded 17 pages/cpu s38996 r8192 d22444 u69632 [ 0.000000] pcpu-alloc: s38996 r8192 d22444 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs mtdparts=pxa3xx_nand-0:5m(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) earlyprintk=serial [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000] Memory: 1009764K/1048576K available (10240K kernel code, 1513K rwdata, 3472K rodata, 1024K init, 470K bss, 38812K reserved, 0K cma-reserved, 262144K highmem) [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C: DT/platform modifies aux control register: 0x06070000 -> 0x16070000 [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 D prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] kfence: initialized - using 2097152 bytes for 255 objects at 0x(ptrval)-0x(ptrval) [ 0.000000] sched_clock: 64 bits at 666MHz, resolution 1ns, wraps every 4398046511103ns [ 0.008678] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x999999d70a, max_idle_ns: 440795225152 ns [ 0.020385] Switching to timer-based delay loop, resolution 1ns [ 0.027199] Ignoring duplicate/late registration of read_current_timer delay [ 0.034916] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.047259] Console: colour dummy device 80x30 [ 0.052405] Calibrating delay loop (skipped), value calculated using timer frequency.. 1332.00 BogoMIPS (lpj=6660000) [ 0.063678] pid_max: default: 32768 minimum: 301 [ 0.069186] LSM: Security Framework initializing [ 0.074628] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.082615] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.091692] CPU: Testing write buffer coherency: ok [ 0.097277] CPU0: Spectre v2: using BPIALL workaround [ 0.103209] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.110265] cblist_init_generic: Setting adjustable number of callback queues. [ 0.118179] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.125022] cblist_init_generic: Setting shift to 1 and lim to 1. [ 0.131889] Setting up static identity map for 0x100000 - 0x100060 [ 0.138862] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4 [ 0.144787] mvebu-pmsu: Initializing Power Management Service Unit [ 0.151784] rcu: Hierarchical SRCU implementation. [ 0.157267] rcu: Max phase no-delay instances is 1000. [ 0.163859] smp: Bringing up secondary CPUs ... [ 0.169627] Booting CPU 1 [ 0.173094] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.173105] CPU1: Spectre v2: using BPIALL workaround [ 0.185249] smp: Brought up 1 node, 2 CPUs [ 0.190051] SMP: Total of 2 processors activated (2664.00 BogoMIPS). [ 0.197084] CPU: All CPU(s) started in SVC mode. [ 0.202825] devtmpfs: initialized [ 0.210275] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.218912] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.229434] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.236986] prandom: seed boundary self test passed [ 0.244141] prandom: 100 self tests passed [ 0.248919] pinctrl core: initialized pinctrl subsystem [ 0.255728] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.263036] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.271265] audit: initializing netlink subsys (disabled) [ 0.277538] audit: type=2000 audit(0.250:1): state=initialized audit_enabled=0 res=1 [ 0.277900] thermal_sys: Registered thermal governor 'step_wise' [ 0.286151] cpuidle: using governor ladder [ 0.297640] cpuidle: using governor menu [ 0.302359] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.311039] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.317695] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling [ 0.326451] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling [ 0.537196] raid6: int32x8 gen() 244 MB/s [ 0.707071] raid6: int32x4 gen() 262 MB/s [ 0.877074] raid6: int32x2 gen() 459 MB/s [ 1.047082] raid6: int32x1 gen() 532 MB/s [ 1.052030] raid6: using algorithm int32x1 gen() 532 MB/s [ 1.227083] raid6: .... xor() 205 MB/s, rmw enabled [ 1.232641] raid6: using intx1 recovery algorithm [ 1.238720] SCSI subsystem initialized [ 1.243291] libata version 3.00 loaded. [ 1.243449] usbcore: registered new interface driver usbfs [ 1.249674] usbcore: registered new interface driver hub [ 1.255684] usbcore: registered new device driver usb [ 1.261678] pps_core: LinuxPPS API ver. 1 registered [ 1.267328] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 1.277181] PTP clock support registered [ 1.282759] vgaarb: loaded [ 1.286541] clocksource: Switched to clocksource arm_global_timer [ 1.293840] VFS: Disk quotas dquot_6.6.0 [ 1.298568] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.313441] NET: Registered PF_INET protocol family [ 1.319225] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 1.328878] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 1.338070] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.346500] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.354984] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.362896] TCP: Hash tables configured (established 8192 bind 8192) [ 1.370162] MPTCP token hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 1.378297] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.385603] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.393483] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.400348] RPC: Registered named UNIX socket transport module. [ 1.406984] RPC: Registered udp transport module. [ 1.412364] RPC: Registered tcp transport module. [ 1.417766] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.424878] PCI: CLS 0 bytes, default 64 [ 1.429595] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.429663] Trying to unpack rootfs image as initramfs... [ 1.442929] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 1.453083] Initialise system trusted keyrings [ 1.458302] Key type blacklist registered [ 1.463250] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 1.470603] zbud: loaded [ 1.475228] NFS: Registering the id_resolver key type [ 1.481141] Key type id_resolver registered [ 1.486010] Key type id_legacy registered [ 1.490774] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.498183] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.562083] xor: measuring software checksum speed [ 1.572124] arm4regs : 2172 MB/sec [ 1.583111] 8regs : 1668 MB/sec [ 1.593853] 32regs : 1733 MB/sec [ 1.598938] xor: using function: arm4regs (2172 MB/sec) [ 1.604852] async_tx: api initialized (async) [ 1.609917] Key type asymmetric registered [ 1.614697] Asymmetric key parser 'x509' registered [ 1.866319] Freeing initrd memory: 10200K [ 1.887695] alg: self-tests for CTR-KDF (hmac(sha256)) passed [ 1.894306] bounce: pool size: 64 pages [ 1.898960] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 1.907129] io scheduler bfq registered [ 1.914290] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 1.922979] debugfs: Directory 'f1018100.gpio' with parent 'regmap' already present! [ 1.932137] debugfs: Directory 'f1018140.gpio' with parent 'regmap' already present! [ 1.941499] mv_xor f1060800.xor: Marvell shared XOR driver [ 2.017187] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 2.027335] mv_xor f1060900.xor: Marvell shared XOR driver [ 2.087184] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 2.174224] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 2.183577] printk: console [ttyS0] disabled [ 2.209122] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 39, base_baud = 12500000) is a 16550A [ 2.218808] printk: console [ttyS0] enabled [ 2.228630] printk: bootconsole [earlycon0] disabled [ 2.261186] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 40, base_baud = 12500000) is a 16550A [ 2.272871] ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator [ 2.281412] ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator [ 2.289717] ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator [ 2.298356] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 2.308169] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 2.319057] scsi host0: ahci-mvebu [ 2.323837] scsi host1: ahci-mvebu [ 2.328311] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 41 [ 2.336991] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 41 [ 2.346812] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xda [ 2.353910] nand: Macronix MX30LF2G18AC [ 2.358495] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 2.367154] Bad block table found at page 131008, version 0x01 [ 2.374037] Bad block table found at page 130944, version 0x01 [ 2.380791] nand_read_bbt: bad block at 0x000002020000 [ 2.386678] nand_read_bbt: bad block at 0x0000062e0000 [ 2.392550] nand_read_bbt: bad block at 0x00000bac0000 [ 2.398440] nand_read_bbt: bad block at 0x00000d300000 [ 2.404308] nand_read_bbt: bad block at 0x00000dc60000 [ 2.410220] 8 cmdlinepart partitions found on MTD device pxa3xx_nand-0 [ 2.417507] Creating 8 MTD partitions on "pxa3xx_nand-0": [ 2.423638] 0x000000000000-0x000000500000 : "u-boot" [ 2.430402] 0x000000500000-0x000000a00000 : "kernel" [ 2.437036] 0x000000a00000-0x000000f00000 : "uRamdisk" [ 2.443837] 0x000000f00000-0x00000c800000 : "image.cfs" [ 2.451114] 0x00000c800000-0x00000d700000 : "rescue_fw" [ 2.458031] 0x00000d700000-0x00000eb00000 : "config" [ 2.464679] 0x00000eb00000-0x00000f500000 : "reserve1" [ 2.471510] 0x00000f500000-0x00000ff00000 : "reserve2" [ 2.478959] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 2.487587] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 2.507981] hwmon hwmon0: temp1_input not attached to any thermal zone [ 2.516011] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled [ 2.529472] mvneta f1034000.ethernet eth0: Using random mac address 32:c8:0a:96:de:97 [ 2.538736] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.546025] ehci-pci: EHCI PCI platform driver [ 2.551330] ehci-orion: EHCI orion driver [ 2.556263] orion-ehci f1058000.usb: EHCI Host Controller [ 2.562457] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 2.570921] orion-ehci f1058000.usb: irq 44, io mem 0xf1058000 [ 2.606557] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 2.613468] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.00 [ 2.622521] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.630514] usb usb1: Product: EHCI Host Controller [ 2.636137] usb usb1: Manufacturer: Linux 6.0.7-mvebu-tld-1 ehci_hcd [ 2.643253] usb usb1: SerialNumber: f1058000.usb [ 2.649229] hub 1-0:1.0: USB hub found [ 2.653754] hub 1-0:1.0: 1 port detected [ 2.660112] usbcore: registered new interface driver usblp [ 2.666483] usbcore: registered new interface driver usb-storage [ 2.673707] mousedev: PS/2 mouse device common for all mice [ 2.680049] ata1: SATA link down (SStatus 0 SControl 300) [ 2.686215] ata2: SATA link down (SStatus 0 SControl 300) [ 2.692771] armada38x-rtc f10a3800.rtc: registered as rtc0 [ 2.699306] armada38x-rtc f10a3800.rtc: setting system clock to 2022-12-17T07:56:34 UTC (1671263794) [ 2.709978] i2c_dev: i2c /dev entries driver [ 2.715255] mv64xxx_i2c f1011000.i2c: can't get pinctrl, bus recovery not supported [ 2.724314] mv64xxx_i2c f1011100.i2c: can't get pinctrl, bus recovery not supported [ 2.736428] orion_wdt: Initial timeout 171 sec [ 2.742220] device-mapper: uevent: version 1.0.3 [ 2.747821] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 2.757263] device-mapper: multipath round-robin: version 1.2.0 loaded [ 2.764531] device-mapper: multipath queue-length: version 0.2.0 loaded [ 2.771901] device-mapper: multipath service-time: version 0.3.0 loaded [ 2.779298] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 2.786125] device-mapper: raid: Loading target version 1.15.1 [ 2.795242] marvell-cesa f1090000.crypto: CESA device successfully registered [ 2.803576] hid: raw HID events driver (C) Jiri Kosina [ 2.809964] usbcore: registered new interface driver usbhid [ 2.816274] usbhid: USB HID core driver [ 2.821394] drop_monitor: Initializing network drop monitor service [ 2.828978] NET: Registered PF_INET6 protocol family [ 2.835699] Segment Routing with IPv6 [ 2.840107] RPL Segment Routing with IPv6 [ 2.844880] In-situ OAM (IOAM) with IPv6 [ 2.849592] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.857784] NET: Registered PF_PACKET protocol family [ 2.863708] 8021q: 802.1Q VLAN Support v1.8 [ 2.868698] Key type dns_resolver registered [ 2.873798] ThumbEE CPU extension supported. [ 2.878839] Registering SWP/SWPB emulation handler [ 2.884868] registered taskstats version 1 [ 2.889737] Loading compiled-in X.509 certificates [ 2.895763] zswap: loaded using pool lzo/zbud [ 2.901237] Key type ._fscrypt registered [ 2.905973] Key type .fscrypt registered [ 2.910633] Key type fscrypt-provisioning registered [ 2.917960] Key type big_key registered [ 2.936788] Key type encrypted registered [ 2.948233] usb_phy_generic usb3_0_phy: dummy supplies not allowed for exclusive requests [ 2.957401] usb_phy_generic usb3_1_phy: dummy supplies not allowed for exclusive requests [ 2.966650] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 2.972710] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 2.981031] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 2.991054] xhci-hcd f10f0000.usb3: irq 45, io mem 0xf10f0000 [ 2.997692] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 3.003755] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 [ 3.012007] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed [ 3.019251] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.00 [ 3.028280] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.036244] usb usb2: Product: xHCI Host Controller [ 3.041865] usb usb2: Manufacturer: Linux 6.0.7-mvebu-tld-1 xhci-hcd [ 3.048962] usb usb2: SerialNumber: f10f0000.usb3 [ 3.054888] hub 2-0:1.0: USB hub found [ 3.059407] hub 2-0:1.0: 1 port detected [ 3.064389] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.073420] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.00 [ 3.082457] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.090481] usb usb3: Product: xHCI Host Controller [ 3.096088] usb usb3: Manufacturer: Linux 6.0.7-mvebu-tld-1 xhci-hcd [ 3.103188] usb usb3: SerialNumber: f10f0000.usb3 [ 3.109045] hub 3-0:1.0: USB hub found [ 3.113540] hub 3-0:1.0: 1 port detected [ 3.118747] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 3.124807] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 3.133139] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 3.143160] xhci-hcd f10f8000.usb3: irq 46, io mem 0xf10f8000 [ 3.149854] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 3.155904] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 [ 3.164157] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed [ 3.171368] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.00 [ 3.180396] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.188367] usb usb4: Product: xHCI Host Controller [ 3.193972] usb usb4: Manufacturer: Linux 6.0.7-mvebu-tld-1 xhci-hcd [ 3.201127] usb usb4: SerialNumber: f10f8000.usb3 [ 3.207119] hub 4-0:1.0: USB hub found [ 3.211618] hub 4-0:1.0: 1 port detected [ 3.216609] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.225550] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.00 [ 3.234663] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.242733] usb usb5: Product: xHCI Host Controller [ 3.248433] usb usb5: Manufacturer: Linux 6.0.7-mvebu-tld-1 xhci-hcd [ 3.255524] usb usb5: SerialNumber: f10f8000.usb3 [ 3.261419] hub 5-0:1.0: USB hub found [ 3.265915] hub 5-0:1.0: 1 port detected [ 3.271768] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.282095] Freeing unused kernel image (initmem) memory: 1024K [ 3.327258] Checked W+X mappings: passed, no W+X pages found [ 3.333664] Run /init as init process [ 3.338084] with arguments: [ 3.338090] /init [ 3.338095] with environment: [ 3.338099] HOME=/ [ 3.338103] TERM=linux [ 3.346642] usb 2-1: new high-speed USB device number 2 using xhci-hcd [ 3.528208] usb 2-1: New USB device found, idVendor=154b, idProduct=005b, bcdDevice=11.00 [ 3.539716] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.547664] usb 2-1: Product: USB 2.0 FD [ 3.552315] usb 2-1: Manufacturer: PNY Technologies [ 3.558386] usb 2-1: SerialNumber: AA00000000021013 [ 3.571760] usb-storage 2-1:1.0: USB Mass Storage device detected [ 3.589205] scsi host2: usb-storage 2-1:1.0 [ 3.639510] usbcore: registered new interface driver uas [ 3.892222] mtdblock: MTD device 'u-boot' is NAND, please consider using UBI block devices instead. [ 3.899815] mtdblock: MTD device 'kernel' is NAND, please consider using UBI block devices instead. [ 3.905077] mtdblock: MTD device 'uRamdisk' is NAND, please consider using UBI block devices instead. [ 3.922744] mtdblock: MTD device 'image.cfs' is NAND, please consider using UBI block devices instead. [ 3.926294] mtdblock: MTD device 'config' is NAND, please consider using UBI block devices instead. [ 3.938027] mtdblock: MTD device 'rescue_fw' is NAND, please consider using UBI block devices instead. [ 3.946421] mtdblock: MTD device 'reserve1' is NAND, please consider using UBI block devices instead. [ 3.957498] mtdblock: MTD device 'reserve2' is NAND, please consider using UBI block devices instead. [ 4.299821] mtdblock: MTD device 'u-boot' is NAND, please consider using UBI block devices instead. [ 4.321007] mtdblock: MTD device 'kernel' is NAND, please consider using UBI block devices instead. [ 4.341946] mtdblock: MTD device 'uRamdisk' is NAND, please consider using UBI block devices instead. [ 4.363123] mtdblock: MTD device 'image.cfs' is NAND, please consider using UBI block devices instead. [ 4.466893] mtdblock: MTD device 'rescue_fw' is NAND, please consider using UBI block devices instead. [ 4.506473] mtdblock: MTD device 'config' is NAND, please consider using UBI block devices instead. [ 4.526174] mtdblock: MTD device 'reserve1' is NAND, please consider using UBI block devices instead. [ 4.545901] mtdblock: MTD device 'reserve2' is NAND, please consider using UBI block devices instead. [ 4.567108] mtdblock: MTD device 'u-boot' is NAND, please consider using UBI block devices instead. [ 4.588103] mtdblock: MTD device 'kernel' is NAND, please consider using UBI block devices instead. [ 4.609012] mtdblock: MTD device 'uRamdisk' is NAND, please consider using UBI block devices instead. [ 4.630082] mtdblock: MTD device 'image.cfs' is NAND, please consider using UBI block devices instead. [ 4.732995] mtdblock: MTD device 'rescue_fw' is NAND, please consider using UBI block devices instead. [ 4.825679] scsi 2:0:0:0: Direct-Access PNY USB 2.0 FD 1100 PQ: 0 ANSI: 4 [ 4.835928] sd 2:0:0:0: [sda] 7975296 512-byte logical blocks: (4.08 GB/3.80 GiB) [ 4.845030] sd 2:0:0:0: [sda] Write Protect is off [ 4.850577] sd 2:0:0:0: [sda] Mode Sense: 43 00 00 00 [ 4.851009] sd 2:0:0:0: [sda] No Caching mode page found [ 4.857087] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 4.866662] sda: sda1 [ 4.870016] sd 2:0:0:0: [sda] Attached SCSI removable disk [ 34.956850] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 38.606570] random: crng init done [ 39.105224] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: none. [ 40.706129] mtdblock: MTD device 'u-boot' is NAND, please consider using UBI block devices instead. [ 40.716361] mtdblock: MTD device 'kernel' is NAND, please consider using UBI block devices instead. [ 40.723470] mtdblock: MTD device 'image.cfs' is NAND, please consider using UBI block devices instead. [ 40.726359] mtdblock: MTD device 'uRamdisk' is NAND, please consider using UBI block devices instead. [ 40.753429] mtdblock: MTD device 'rescue_fw' is NAND, please consider using UBI block devices instead. [ 40.780338] mtdblock: MTD device 'config' is NAND, please consider using UBI block devices instead. [ 40.786708] mtdblock: MTD device 'reserve1' is NAND, please consider using UBI block devices instead. [ 40.802837] mtdblock: MTD device 'reserve2' is NAND, please consider using UBI block devices instead. [ 40.919942] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 42.160315] EXT4-fs (sda1): re-mounted. Quota mode: none. [ 43.417550] mvneta f1034000.ethernet eth0: PHY [f1072004.mdio-mii:00] driver [Marvell 88E1510] (irq=POLL) [ 43.429169] mvneta f1034000.ethernet eth0: configuring for phy/sgmii link mode [ 47.626987] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 47.635767] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 17, 2022 03:40PM |
Admin Registered: 13 years ago Posts: 18,545 |
What you observed:
Rootfs instruction:
Since many kernel versions ago, for Marvell Armada boxes such as this one, the kernel has been default to generate a random MAC address. This in and by itself is not bad, but could cause the dynamic IP to be a different one at each system boots. So I added that set_persistent_mac_address script to help setting to the real MAC address.
Now the reason why that script did not work can be seen with the warning message below. These are not errors, just warning that the u-boot envs are not accessible, so the env ethaddr is not defined. The script set_persistent_mac_address uses this env to set the MAC address.
So this is something that you don't have yet. The ability to print and set env using fw_printenv and fw_setenv commands. I recall that in the working thread this topic was done already. Let's see if we can find it.
=====
Note: thanks to one of our experienced users, this script will be improved and posted later. But it should work OK for now.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 12/17/2022 03:44PM by bodhi.
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1024
link/ether c2:90:9a:b0:fd:d6 brd ff:ff:ff:ff:ff:ff. (It's wrong)
inet 192.168.1.97/24 brd 192.168.1.255 scope global dynamic eth0
valid_lft 86041sec preferred_lft 86041sec
inet6 fe80::c090:9aff:feb0:fdd6/64 scope link
valid_lft forever preferred_lft forever
is not wrong. c2:90:9a:b0:fd:d6 is a random MAC address generated by the kernel. It happens each time the system boot up.
Rootfs instruction:
Quote
https://forum.doozan.com/read.php?2,32146
Note 6 (Optional):
To enable the network dynamic IP to stay consistent after each reboot, and also for faster boot. In this rootfs, a script is executed during kernel booting (in /etc/rc.local), to detect if a local MAC address was assigned during boot, and then set the persistent MAC address to what is currently defined in u-boot env ethaddr.
/root/set_persistent_mac_address
To keep using the kernel generated local MAC address (if local MAC address was generated in your box) then remove or rename this script.
Since many kernel versions ago, for Marvell Armada boxes such as this one, the kernel has been default to generate a random MAC address. This in and by itself is not bad, but could cause the dynamic IP to be a different one at each system boots. So I added that set_persistent_mac_address script to help setting to the real MAC address.
Now the reason why that script did not work can be seen with the warning message below. These are not errors, just warning that the u-boot envs are not accessible, so the env ethaddr is not defined. The script set_persistent_mac_address uses this env to set the MAC address.
Cannot read environment, using default Cannot read default environment from file <13>Dec 16 23:32:44 root[2599]: Cannot read u-boot env ethaddr
So this is something that you don't have yet. The ability to print and set env using fw_printenv and fw_setenv commands. I recall that in the working thread this topic was done already. Let's see if we can find it.
=====
Note: thanks to one of our experienced users, this script will be improved and posted later. But it should work OK for now.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 12/17/2022 03:44PM by bodhi.
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 17, 2022 03:50PM |
Registered: 1 year ago Posts: 142 |
Hi,
Great explanation, thanks,
With the custom kernel I can print the env
Perhaps I would need to install u-boot tool?
Anyway, I think everything is set and working fine.
Could you please help me setting the env to boot automatically from USB?
I found a guy that seems you helped too, with the following, but I don’t know if they could work with mine
I guess, I would need to change the memory address where boot the uImage and uRamdisk, change fatload with ext2load… anything else?
Edited 4 time(s). Last edit at 12/17/2022 04:13PM by i5Js.
Great explanation, thanks,
With the custom kernel I can print the env
Perhaps I would need to install u-boot tool?
Anyway, I think everything is set and working fine.
Could you please help me setting the env to boot automatically from USB?
I found a guy that seems you helped too, with the following, but I don’t know if they could work with mine
setenv set_bootargs_stock 'setenv bootargs root=/dev/ram console=ttyS0,115200' setenv bootcmd_stock 'echo Booting from stock ... ; run set_bootargs_stock; printenv bootargs; nand read.e 0xa00000 0x500000 0x500000;nand read.e 0xf00000 0xa00000 0x500000;bootm 0xa00000 0xf00000' setenv bootdev 'usb' setenv device '0:1' setenv load_image_addr '0x02000020' setenv load_initrd_addr '0x2900000' setenv load_image 'echo loading Image ...; fatload $bootdev $device $load_image_addr /boot/uImage' setenv load_initrd 'echo loading uInitrd ...; fatload $bootdev $device $load_initrd_addr /boot/uInitrd' setenv usb_set_bootargs 'setenv bootargs "console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts earlyprintk=serial init=/bin/systemd"' setenv bootcmd_usb 'echo Booting from USB ...; usb start; run usb_set_bootargs; if run load_image; then if run load_initrd; then bootm $load_image_addr $load_initrd_addr; else bootm $load_image_addr; fi; fi; usb stop' setenv bootcmd 'setenv fdt_skip_update yes; setenv usbActive 0; run bootcmd_usb; setenv usbActive 1; run bootcmd_usb; setenv fdt_skip_update no; run bootcmd_stock; reset' saveenv reset
I guess, I would need to change the memory address where boot the uImage and uRamdisk, change fatload with ext2load… anything else?
Edited 4 time(s). Last edit at 12/17/2022 04:13PM by i5Js.
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 17, 2022 04:20PM |
Admin Registered: 13 years ago Posts: 18,545 |
i5Js,
No need to do all that. You are all done, except for this u-boot envs accessiblity in Debian.
The only thing you need is the content of the file
So search the working thread backward, until you see the file and perhaps a few posts before and after that.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
No need to do all that. You are all done, except for this u-boot envs accessiblity in Debian.
The only thing you need is the content of the file
/etc/fw_env.config
So search the working thread backward, until you see the file and perhaps a few posts before and after that.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 17, 2022 04:23PM |
Registered: 1 year ago Posts: 142 |
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 17, 2022 10:39PM |
Admin Registered: 13 years ago Posts: 18,545 |
You were booting into the USB rootfs here:
and here:
https://forum.doozan.com/read.php?2,67249,133655#msg-133655
So to repeat it and making permanent.
and then
At this point, you're done. The only remain big issue is the random MAC at each boot. The LEDs is a minor thing, nice to have.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Marvell>> setenv usbActive 0
Marvell>> setenv usbType 3
Marvell>> usb start
(Re)start USB...
USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Marvell>> setenv set_bootargs_debian "setenv bootargs console=ttyS0,115200 root=LABEL=rootfs mtdparts=pxa3xx_nand-0:5m(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) earlyprintk=serial"
Marvell>> setenv boot_debian_usb "usb start; sleep 5; ext2load usb 0:1 0x00800000 boot/uImage; ext2load usb 0:1 0x02100000 boot/uRamdisk; bootm 0x00800000 0x02100000"
Marvell>> setenv bootcmd "run set_bootargs_debian; run boot_debian_usb; reset"
and here:
https://forum.doozan.com/read.php?2,67249,133655#msg-133655
So to repeat it and making permanent.
setenv usbActive 0 setenv usbType 3 setenv set_bootargs_debian "setenv bootargs console=ttyS0,115200 root=LABEL=rootfs mtdparts=pxa3xx_nand-0:5m(u-boot),5m@5m(kernel),5m@10m(uRamdisk),185m@15m(image.cfs),15m@200m(rescue_fw),20m@215m(config),10m@235m(reserve1),10m@245m(reserve2) earlyprintk=serial" setenv boot_debian_usb "usb start; sleep 5; ext2load usb 0:1 0x00800000 /boot/uImage; ext2load usb 0:1 0x02100000 /boot/uRamdisk; bootm 0x00800000 0x02100000" setenv bootcmd "run set_bootargs_debian; run boot_debian_usb; reset"
and then
saveenv bootLet it boot into Debian. Login and then reboot. Let it boot automatically, it should boot again into the USB rootfs.
At this point, you're done. The only remain big issue is the random MAC at each boot. The LEDs is a minor thing, nice to have.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 18, 2022 04:07PM |
Registered: 1 year ago Posts: 142 |
Well finally it is complete.
I have the box ready an working with OMV 6. And it works great!!
I want to thank you Bodhi for all your help, all the time you have spent with me!
I will try to write down a guide with all my steps, advices, and of course all my mistakes
Perhaps it would take time because the Christmas, family and work, but for sure I will
Stay tune
Be cool!
Best
i5Js
I have the box ready an working with OMV 6. And it works great!!
I want to thank you Bodhi for all your help, all the time you have spent with me!
I will try to write down a guide with all my steps, advices, and of course all my mistakes
Perhaps it would take time because the Christmas, family and work, but for sure I will
Stay tune
Be cool!
Best
i5Js
|
Re: Debian Stretch on Sata disk in WD MyCloud EX2 Ultra December 18, 2022 04:40PM |
Admin Registered: 13 years ago Posts: 18,545 |
> Well finally it is complete.
>
> I have the box ready an working with OMV 6. And it
> works great!!
Cool!
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
>
> I have the box ready an working with OMV 6. And it
> works great!!
Cool!
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
