Re: Debian on Synology RS816 (Armada 385) May 21, 2019 04:26AM |
Admin Registered: 14 years ago Posts: 19,317 |
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 04:34AM |
Admin Registered: 14 years ago Posts: 19,317 |
root@debian:~# flash_unlock /dev/mtd1 root@debian:~# flashcp -v rs816.dtb.mtd1.kwb /dev/mtd1 Erasing blocks: 16/16 (100%) Writing data: 64k/64k (100%) Verifying data: 64k/64k (100%) root@debian:~# flash_unlock /dev/mtd2 root@debian:~# flashcp -v rs816.zImage.mtd2.kwb /dev/mtd2 Erasing blocks: 1776/1776 (100%) Writing data: 7104k/7104k (100%) Verifying data: 7104k/7104k (100%)
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 04:35AM |
Registered: 5 years ago Posts: 257 |
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 04:38AM |
Admin Registered: 14 years ago Posts: 19,317 |
setenv mtdparts 'mtdparts=spi0.0:896k(u-boot),64k(dtb),7104k(kernel),-(env)'
setenv boot_config_spi 'setenv image_addr_spi 0x0F0000; setenv image_size_spi 0x006f0000; setenv dtb_addr_spi 0x0E0000; setenv dtb_size_spi 0x010000; sf probe 0 50000000' setenv load_image_spi 'echo loading zImage from flash ...; sf read $load_image_addr $image_addr_spi $image_size_spi' setenv load_dtb_spi 'echo loading DTB from flash ...; sf read $loadaddr_dt $dtb_addr_spi $dtb_size_spi' setenv bootcmd_exec 'echo Booting Debian ...; run set_bootargs; setenv fdt_skip_update yes; setenv initrd_high 0xffffffff; run boot_config_spi; run load_image_spi; run load_dtb_spi; bootz $load_image_addr - $load_dtb_addr'
printenv boot
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 04:48AM |
Admin Registered: 14 years ago Posts: 19,317 |
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 04:52AM |
Admin Registered: 14 years ago Posts: 19,317 |
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 04:53AM |
Registered: 5 years ago Posts: 257 |
setenv boot_config_spi 'setenv image_addr_spi 0x0F0000; setenv image_size_spi 0x006f0000; setenv dtb_addr_spi 0x0E0000; setenv dtb_size_spi 0x010000; sf probe 0 50000000' setenv load_image_spi 'echo loading zImage from flash ...; sf read $load_image_addr $image_addr_spi $image_size_spi' setenv load_dtb_spi 'echo loading DTB from flash ...; sf read $loadaddr_dt $dtb_addr_spi $dtb_size_spi' bootcmd_exec='echo Booting Debian ...; run set_bootargs; setenv fdt_skip_update yes; setenv initrd_high 0xffffffff; run boot_config_spi; run load_image_spi; run load_dtb_spi; bootz $load_image_addr - $load_dtb_addr'
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 04:55AM |
Registered: 5 years ago Posts: 257 |
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 04:55AM |
Admin Registered: 14 years ago Posts: 19,317 |
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 05:06AM |
Registered: 5 years ago Posts: 257 |
BootROM - 1.73 Booting from SPI flash General initialization - Version: 1.0.0 AVS selection from EFUSE disabled (Skip reading EFUSE values) Detected Device ID 6820 High speed PHY - Version: 2.0 Init Synology board board SerDes lanes topology details: | Lane # | Speed| Type | ------------------------------| | 0 | 0 | SGMII0 | | 1 | 6 | SATA0 | | 2 | 5 | PCIe1 | | 3 | 0 | SGMII2 | | 4 | 5 | USB3 HOST0 | | 5 | 5 | USB3 HOST1 | ------------------------------- High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.46.0 WARNING:Wrong configuration for pup #1 CS mask and CS mirroring for all pups should be the same WARNING:Wrong configuration for pup #3 CS mask and CS mirroring for all pups should be the same DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully Not detected suspend to RAM indication BootROM: Image checksum verification PASSED l __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01-g74a026b-dirty (Dec 30 2015 - 14:40:58) Marvell version: 2015_T1.0p16 Board: SYNO-RS816 SoC: MV88F6820 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1866 [MHz] L2 @ 933 [MHz] TClock @ 200 [MHz] DDR3 @ 933 [MHz] DDR3 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 1 GiB MMC: mv_sdh: 0 SF: Detected N25Q64 with page size 64 KiB, total 8 MiB PCI-e 1 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 2.0 USB3.0 0: Host Mode USB3.0 1: Host Mode Map: Code: 0x3ff3b000:0x3ffc91bc BSS: 0x3ffef688 Stack: 0x3fa2af20 Heap: 0x3fa2b000:0x3ff3b000 U-Boot Environment: 0x007e0000:0x007f0000 (SPI) Board configuration detected: Synology Model: RS816 Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | SGMII | 0x01 | | egiga2 | SGMII | 0x00 | egiga0 [PRIME], egiga2 Press Ctrl+C to abort autoboot in 3 second Marvell>> setenv mtdparts 'mtdparts=spi0.0:896k(u-boot),64k(dtb),7104k(kernel),-(env)' Marvell>> setenv boot_config_spi 'setenv image_addr_spi 0x0F0000; setenv image_size_spi 0x006f0000; setenv dtb_addr_spi 0x0E0000; setenv dtb_size_spi 0x010000; sf probe 0 50000000' Marvell>> setenv load_image_spi 'echo loading zImage from flash ...; sf read $load_image_addr $image_addr_spi $image_size_spi' Marvell>> setenv load_dtb_spi 'echo loading DTB from flash ...; sf read $loadaddr_dt $dtb_addr_spi $dtb_size_spi' Marvell>> setenv bootcmd_exec 'echo Booting Debian ...; run set_bootargs; setenv fdt_skip_update yes; setenv initrd_high 0xffffffff; run boot_config_spi; run load_image_spi; run load_dtb_spi; bootz $load_image_addr - $load_dtb_addr' Marvell>> printenv CASset=max MALLOC_len=5 MPmode=SMP ata_hdd_detect=syno_hdd_detect=39,39,39,39 ata_hdd_enable=syno_hdd_enable=37,37,37,37 autoload=no baudrate=115200 boot_config_spi=setenv image_addr_spi 0x0F0000; setenv image_size_spi 0x006f0000; setenv dtb_addr_spi 0x0E0000; setenv dtb_size_spi 0x010000; sf probe 0 50000000 boot_order=hd_scr usb_scr mmc_scr hd_img usb_img mmc_img pxe net_img net_scr bootargs= bootargs_dflt=$console $nandEcc $mtdparts_lgcy $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel bootargs_end=:10.4.50.254:255.255.255.0:Armada38x:eth0:none bootargs_root=root=/dev/nfs rw bootcmd=run bootcmd_exec; run bootspi bootcmd_auto=stage_boot $boot_order bootcmd_exec=echo Booting Debian ...; run set_bootargs; setenv fdt_skip_update yes; setenv initrd_high 0xffffffff; run boot_config_spi; run load_image_spi; run load_dtb_spi; bootz $load_image_addr - $load_dtb_addr bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_boot=tftpboot 0x2000000 $image_name; setenv bootargs $console $nandEcc $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr; bootcmd_fdt_edit=tftpboot $fdtaddr $fdtfile; fdt addr $fdtaddr; setenv bootcmd $bootcmd_fdt_boot bootcmd_lgcy=tftpboot 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts_lgcy $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootm $loadaddr; bootdelay=3 bootftp=run syno_bootargs;tftpboot $loadaddr_kernel $file_kernel;tftpboot $loadaddr_rootfs $file_rootfs;sf probe; sf read $loadaddr_dt $spi_pt_addr_dt $spi_pt_size_dt;fdt addr $loadaddr_dt;bootm $loadaddr_kernel $loadaddr_rootfs $loadaddr_dt; bootspi=run syno_bootargs;sf probe 0 50000000;sf read $loadaddr_kernel $spi_pt_addr_kernel $spi_pt_size_kernel;sf read $loadaddr_rootfs $spi_pt_addr_rootfs $spi_pt_size_rootfs;sf read $loadaddr_dt $spi_pt_addr_dt $spi_pt_size_dt;bootm $loadaddr_kernel $loadaddr_rootfs $loadaddr_dt; cacheShare=no clean_env=sf probe; sf erase $spi_pt_addr_env $spi_pt_size_env; console=console=ttyS0,115200 device_partition=0:1 disaMvPnp=no eeeEnable=no enaClockGating=no enaCpuStream=no enaFPU=yes enaMonExt=no enaWrAllo=no eth1addr=00:50:43:1c:24:27 eth1mtu=1500 eth2addr=00:50:43:1c:1c:27 eth2mtu=1500 eth3addr=00:50:43:24:1c:1c eth3mtu=1500 ethact=egiga0 ethaddr=00:50:43:1c:24:27 ethmtu=1500 ethprime=egiga0 fdt_addr=2040000 fdt_skip_update=yes fdtaddr=0x1000000 fdtfile=armada-38x.dtb file_flash=armada38x/flash.bin file_kernel=armada38x/uImage file_rootfs=armada38x/rd.bin file_uboot=armada38x/uboot.bin ide_path=/ image_name=uImage initrd_high=8000000 initrd_name=uInitrd ipaddr=192.168.1.250 kernel_addr_r=2080000 lcd0_enable=0 lcd0_params=640x480-16@60 lcd_panel=0 limit_dram_size=yes load_dtb=echo loading DTB from tftpserver ...; tftpboot $load_dtb_addr armada-385-synology-rs816-v12.dtb load_dtb_addr=0x1000000 load_dtb_spi=echo loading DTB from flash ...; sf read $loadaddr_dt $dtb_addr_spi $dtb_size_spi load_image=echo loading zImage from tftpserver ...; tftpboot $load_image_addr zImage load_image_addr=0x02000000 load_image_spi=echo loading zImage from flash ...; sf read $load_image_addr $image_addr_spi $image_size_spi load_initrd=echo loading uInitrd from tftpserver ...; tftpboot $load_initrd_addr uInitrd load_initrd_addr=0x3000000 loadaddr=0x02000000 loadaddr_dt=0x1000000 loadaddr_kernel=0x2000000 loadaddr_rootfs=0x3000000 loads_echo=0 mtdids=spi0=spi_flash mtdparts=mtdparts=spi0.0:896k(u-boot),64k(dtb),7104k(kernel),-(env) mtdparts_lgcy=mtdparts=spi_flash:4m(boot),-(spi-rootfs) mvNetConfig=mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 mv_pon_addr=00:50:43:27:1c:1c netbsd_en=no netretry=no pcieTune=no pexMode=RC pxe_files_load=:default.arm-armadaxp-db:default.arm-armadaxp:default.arm pxefile_addr_r=3100000 ramdisk_addr_r=2880000 rootpath=/srv/nfs/ run_script=no sata_delay_reset=0 sata_dma_mode=yes script_addr_r=3000000 script_name=boot.scr sd_detection_dat3=no serverip=192.168.1.2 set_bootargs=setenv bootargs "console=ttyS0,115200 root=/dev/sda1 rootdelay=20 $mtdparts earlyprintk=serial" spi_pt_addr_dt=0x0E0000 spi_pt_addr_env=0x7e0000 spi_pt_addr_kernel=0x0F0000 spi_pt_addr_rootfs=0x3C0000 spi_pt_size_dt=0x010000 spi_pt_size_env=0x010000 spi_pt_size_kernel=0x2D0000 spi_pt_size_rootfs=0x410000 standalone=fsload 0x2000000 $image_name;setenv bootargs $console $nandEcc $mtdparts_lgcy root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm 0x2000000; stderr=serial stdin=serial stdout=serial syno_boot_dev=/dev/md0 syno_bootargs=setenv bootargs console=ttyS0,115200 ip=off initrd=$loadaddr_rootfs root=$syno_boot_dev rw $syno_extra_args syno_hw_version=$syno_hw_version hd_power_on_seq=$syno_hdd_powerup_seq ihd_num=$syno_hdd_powerup_seq netif_num=$syno_net_if_num $ata_hdd_detect $ata_hdd_enable flash_size=8 syno_extra_args=HddHotplug=4 sata_remap=0>4:4>0 syno_hdd_powerup_seq=4 syno_hw_version=RS816 syno_net_if_num=2 upd_flash=setenv tftpfile $file_flash; tftpboot $loadaddr $tftpfile; if test $? -eq 0; then echo "This may take a while, please be patient..."; sf probe; sf erase 0 +$filesize; sf write $loadaddr 0 $filesize; echo "\ Flash Update Done"; fi; upd_kernel=setenv tftpfile $file_kernel; mw.b $loadaddr 0xFF $spi_pt_size_kernel; tftpboot $loadaddr $tftpfile; if test $? -eq 0; then sf probe; sf erase $spi_pt_addr_kernel $spi_pt_size_kernel; sf write $loadaddr $spi_pt_addr_kernel $spi_pt_size_kernel; echo "\ Kernel Update Done"; fi; upd_rootfs=setenv tftpfile $file_rootfs; mw.b $loadaddr 0xFF $spi_pt_size_rootfs; tftpboot $loadaddr $tftpfile; if test $? -eq 0; then sf probe; sf erase $spi_pt_addr_rootfs +$filesize; sf write $loadaddr $spi_pt_addr_rootfs $filesize; echo "\ Rootfs Update Done"; fi; upd_uboot=setenv tftpfile $file_uboot; tftpboot $loadaddr $tftpfile; if test $? -eq 0; then sf probe; sf erase 0 +$filesize; sf write $loadaddr 0 $filesize; echo "\ Uboot Update Done"; fi; usb0Mode=host usbActive=0 usbType=2 usb_setup=setenv usbActive 1; setenv usbType 3; usb start; vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 6893/65532 bytes Marvell>> boot Booting Debian ... SF: Detected N25Q64 with page size 64 KiB, total 8 MiB loading zImage from flash ... loading DTB from flash ... ## Flattened Device Tree blob at 01000000 Booting using the fdt blob at 0x01000000 Loading Device Tree to 00ff8000, end 00fff758 ... OK Skipping Device Tree update ('fdt_skip_update' = yes) Limit DDR size at 3GB due to power of 2 requirement of Address decoding Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.1.2-rj (root@debian) (gcc version 8.3.0 (Debian 8.3.0-6)) #1 SMP PREEMPT Sun May 19 12:13:42 AWST 2019 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Synology RS116 [ 0.000000] printk: bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] random: get_random_bytes called from start_kernel+0x78/0x4dc with crng_init=0 [ 0.000000] percpu: Embedded 18 pages/cpu s41932 r8192 d23604 u73728 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=20 mtdparts=spi0.0:896k(u-boot),64k(dtb),7104k(kernel),-(env) earlyprintk=serial [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1024864K/1048576K available (9216K kernel code, 836K rwdata, 2496K rodata, 1024K init, 330K bss, 23712K reserved, 0K cma-reserved, 262144K highmem) [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 D prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001 [ 0.000006] sched_clock: 64 bits at 933MHz, resolution 1ns, wraps every 4398046511103ns [ 0.007975] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x1ae5b571769, max_idle_ns: 881590513431 ns [ 0.019059] Switching to timer-based delay loop, resolution 1ns [ 0.025106] Ignoring duplicate/late registration of read_current_timer delay [ 0.032122] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.043339] Console: colour dummy device 80x30 [ 0.047777] Calibrating delay loop (skipped), value calculated using timer frequency.. 1866.00 BogoMIPS (lpj=9330000) [ 0.058340] pid_max: default: 32768 minimum: 301 [ 0.063017] LSM: Security Framework initializing [ 0.067657] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.074240] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.081537] *** VALIDATE proc *** [ 0.084911] *** VALIDATE cgroup1 *** [ 0.088475] *** VALIDATE cgroup2 *** [ 0.092054] CPU: Testing write buffer coherency: ok [ 0.096919] CPU0: Spectre v2: using BPIALL workaround [ 0.102047] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.165011] Setting up static identity map for 0x100000 - 0x100060 [ 0.171225] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4 [ 0.176427] mvebu-pmsu: Initializing Power Management Service Unit [ 0.194992] rcu: Hierarchical SRCU implementation. [ 0.234991] smp: Bringing up secondary CPUs ... [ 0.295046] Booting CPU 1 [ 0.297787] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.297790] CPU1: Spectre v2: using BPIALL workaround [ 0.308507] smp: Brought up 1 node, 2 CPUs [ 0.312582] SMP: Total of 2 processors activated (3732.00 BogoMIPS). [ 0.318920] CPU: All CPU(s) started in SVC mode. [ 0.324002] devtmpfs: initialized [ 0.329013] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.336881] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.346675] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.352838] xor: measuring software checksum speed [ 0.454986] arm4regs : 2937.600 MB/sec [ 0.554988] 8regs : 2220.400 MB/sec [ 0.654986] 32regs : 2348.800 MB/sec [ 0.659147] xor: using function: arm4regs (2937.600 MB/sec) [ 0.664692] prandom: seed boundary self test passed [ 0.670662] prandom: 100 self tests passed [ 0.674736] pinctrl core: initialized pinctrl subsystem [ 0.680599] NET: Registered protocol family 16 [ 0.685496] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.692653] audit: initializing netlink subsys (disabled) [ 0.698100] audit: type=2000 audit(0.670:1): state=initialized audit_enabled=0 res=1 [ 0.715016] cpuidle: using governor ladder [ 0.719103] cpuidle: using governor menu [ 0.723114] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.731134] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.737043] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling [ 0.745112] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling [ 0.935100] raid6: int32x8 gen() 311 MB/s [ 1.105038] raid6: int32x8 xor() 243 MB/s [ 1.275041] raid6: int32x4 gen() 303 MB/s [ 1.445073] raid6: int32x4 xor() 253 MB/s [ 1.615015] raid6: int32x2 gen() 337 MB/s [ 1.785005] raid6: int32x2 xor() 336 MB/s [ 1.955048] raid6: int32x1 gen() 304 MB/s [ 2.125016] raid6: int32x1 xor() 304 MB/s [ 2.129262] raid6: using algorithm int32x2 gen() 337 MB/s [ 2.134632] raid6: .... xor() 336 MB/s, rmw enabled [ 2.139489] raid6: using intx1 recovery algorithm [ 2.145478] vgaarb: loaded [ 2.148399] SCSI subsystem initialized [ 2.152529] usbcore: registered new interface driver usbfs [ 2.158049] usbcore: registered new interface driver hub [ 2.163389] usbcore: registered new device driver usb [ 2.168817] media: Linux media interface: v0.10 [ 2.173362] videodev: Linux video capture interface: v2.00 [ 2.178989] pps_core: LinuxPPS API ver. 1 registered [ 2.183928] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 2.193062] PTP clock support registered [ 2.197757] clocksource: Switched to clocksource arm_global_timer [ 2.545434] VFS: Disk quotas dquot_6.6.0 [ 2.549390] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 2.562340] NET: Registered protocol family 2 [ 2.566984] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 2.574628] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 2.581676] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 2.588140] TCP: Hash tables configured (established 8192 bind 8192) [ 2.594515] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 2.600435] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 2.606887] NET: Registered protocol family 1 [ 2.611475] RPC: Registered named UNIX socket transport module. [ 2.617365] RPC: Registered udp transport module. [ 2.622054] RPC: Registered tcp transport module. [ 2.626733] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.633317] NetWinder Floating Point Emulator V0.97 (double precision) [ 2.639953] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 2.649240] Initialise system trusted keyrings [ 2.653676] Key type blacklist registered [ 2.657731] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 2.664221] zbud: loaded [ 2.667170] NFS: Registering the id_resolver key type [ 2.672226] Key type id_resolver registered [ 2.676387] Key type id_legacy registered [ 2.680388] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.687056] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 2.693490] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 2.700778] orangefs_debugfs_init: called with debug mask: :none: :0: [ 2.707254] orangefs_init: module version upstream loaded [ 2.716261] async_tx: api initialized (async) [ 2.720614] Key type asymmetric registered [ 2.724688] Asymmetric key parser 'x509' registered [ 2.729570] bounce: pool size: 64 pages [ 2.733446] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 2.740853] io scheduler bfq registered [ 2.746165] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 2.754910] mvebu-pcie soc:pcie: PCI host bridge to bus 0000:00 [ 2.760823] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.766282] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] [ 2.773213] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 2.780634] PCI: bus0: Fast back to back transfers disabled [ 2.786184] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.794167] pci 0000:00:03.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.802145] pci 0000:00:04.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.810478] pci 0000:00:02.0: ASPM: current common clock configuration is broken, reconfiguring [ 2.848460] PCI: bus1: Fast back to back transfers disabled [ 2.854774] PCI: bus2: Fast back to back transfers enabled [ 2.861006] PCI: bus3: Fast back to back transfers enabled [ 2.866494] pci 0000:00:02.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 2.873345] pci 0000:00:02.0: BAR 13: assigned [io 0x10000-0x10fff] [ 2.879673] pci 0000:00:02.0: BAR 6: assigned [mem 0xe0100000-0xe01007ff pref] [ 2.886862] pci 0000:00:03.0: BAR 6: assigned [mem 0xe0200000-0xe02007ff pref] [ 2.894054] pci 0000:00:04.0: BAR 6: assigned [mem 0xe0300000-0xe03007ff pref] [ 2.901249] pci 0000:01:00.0: BAR 6: assigned [mem 0xe0000000-0xe000ffff pref] [ 2.908441] pci 0000:01:00.0: BAR 5: assigned [mem 0xe0010000-0xe00107ff] [ 2.915197] pci 0000:01:00.0: BAR 4: assigned [io 0x10000-0x1001f] [ 2.921440] pci 0000:01:00.0: BAR 0: assigned [io 0x10020-0x10027] [ 2.927677] pci 0000:01:00.0: BAR 2: assigned [io 0x10028-0x1002f] [ 2.933919] pci 0000:01:00.0: BAR 1: assigned [io 0x10030-0x10033] [ 2.940161] pci 0000:01:00.0: BAR 3: assigned [io 0x10034-0x10037] [ 2.946399] pci 0000:00:02.0: PCI bridge to [bus 01] [ 2.951343] pci 0000:00:02.0: bridge window [io 0x10000-0x10fff] [ 2.957580] pci 0000:00:02.0: bridge window [mem 0xe0000000-0xe00fffff] [ 2.964341] pci 0000:00:03.0: PCI bridge to [bus 02] [ 2.969287] pci 0000:00:04.0: PCI bridge to [bus 03] [ 2.974275] pcieport 0000:00:02.0: enabling device (0140 -> 0143) [ 2.980829] mv_xor f1060800.xor: Marvell shared XOR driver [ 3.048098] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 3.056393] mv_xor f1060900.xor: Marvell shared XOR driver [ 3.118097] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr ) [ 3.162152] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 3.169735] printk: console [ttyS0] disabled [ 3.194055] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 22, base_baud = 12500000) is a 16550A [ 3.203020] printk: console [ttyS0] enabled [ 3.203020] printk: console [ttyS0] enabled [ 3.211429] printk: bootconsole [earlycon0] disabled [ 3.211429] printk: bootconsole [earlycon0] disabled [ 3.242070] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 23, base_baud = 12500000) is a 16550A [ 3.262101] ahci 0000:01:00.0: AHCI 0001.0000 32 slots 4 ports 6 Gbps 0xf impl SATA mode [ 3.270243] ahci 0000:01:00.0: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 3.279543] scsi host0: ahci [ 3.282719] scsi host1: ahci [ 3.285856] scsi host2: ahci [ 3.289015] scsi host3: ahci [ 3.292094] ata1: SATA max UDMA/133 abar m2048@0xe0010000 port 0xe0010100 irq 48 [ 3.299536] ata2: SATA max UDMA/133 abar m2048@0xe0010000 port 0xe0010180 irq 48 [ 3.306965] ata3: SATA max UDMA/133 abar m2048@0xe0010000 port 0xe0010200 irq 48 [ 3.314398] ata4: SATA max UDMA/133 abar m2048@0xe0010000 port 0xe0010280 irq 48 [ 3.323105] m25p80 spi0.0: found n25q064, expected mx25l6405d [ 3.329011] m25p80 spi0.0: n25q064 (8192 Kbytes) [ 3.333655] 4 cmdlinepart partitions found on MTD device spi0.0 [ 3.339606] Creating 4 MTD partitions on "spi0.0": [ 3.344419] 0x000000000000-0x0000000e0000 : "u-boot" [ 3.349951] 0x0000000e0000-0x0000000f0000 : "dtb" [ 3.355151] 0x0000000f0000-0x0000007e0000 : "kernel" [ 3.360616] 0x0000007e0000-0x000000800000 : "env" [ 3.366469] libphy: Fixed MDIO Bus: probed [ 3.370991] libphy: orion_mdio_bus: probed [ 3.375905] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled [ 3.384511] mvneta f1070000.ethernet eth0: Using random mac address 6e:ac:5c:e0:b6:90 [ 3.392593] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.399170] ehci-pci: EHCI PCI platform driver [ 3.403664] ehci-orion: EHCI orion driver [ 3.408142] usbcore: registered new interface driver usblp [ 3.413675] usbcore: registered new interface driver usb-storage [ 3.419875] mousedev: PS/2 mouse device common for all mice [ 3.426101] armada38x-rtc f10a3800.rtc: registered as rtc0 [ 3.431782] i2c /dev entries driver [ 3.460484] gpio-fan gpio-fan: GPIO fan initialized [ 3.466945] orion_wdt: Initial timeout 171 sec [ 3.483474] marvell-cesa f1090000.crypto: CESA device successfully registered [ 3.490789] hidraw: raw HID events driver (C) Jiri Kosina [ 3.496363] usbcore: registered new interface driver usbhid [ 3.501971] usbhid: USB HID core driver [ 3.506011] drop_monitor: Initializing network drop monitor service [ 3.512533] NET: Registered protocol family 10 [ 3.517448] Segment Routing with IPv6 [ 3.521212] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.527719] NET: Registered protocol family 17 [ 3.532266] 8021q: 802.1Q VLAN Support v1.8 [ 3.536489] Key type dns_resolver registered [ 3.540867] ThumbEE CPU extension supported. [ 3.545159] Registering SWP/SWPB emulation handler [ 3.550259] registered taskstats version 1 [ 3.554374] Loading compiled-in X.509 certificates [ 3.559230] zswap: loaded using pool lzo/zbud [ 3.564441] Key type big_key registered [ 3.568591] Key type encrypted registered [ 3.574162] v5.0-sata0: supplied by pwr_en_sata0 [ 3.578846] v12.0-sata0: supplied by pwr_en_sata0 [ 3.583971] ahci-mvebu f10a8000.sata: masking port_map 0x3 -> 0x1 [ 3.590134] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x1 impl platform mode [ 3.599229] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 3.608465] scsi host4: ahci-mvebu [ 3.612130] scsi host5: ahci-mvebu [ 3.615671] ata5: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 41 [ 3.623638] ata6: DUMMY [ 3.626305] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 3.631684] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 1 [ 3.639264] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 3.648553] xhci-hcd f10f0000.usb3: irq 42, io mem 0xf10f0000 [ 3.649017] ata1: SATA link down (SStatus 0 SControl 300) [ 3.654483] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.01 [ 3.659819] ata2: SATA link down (SStatus 0 SControl 300) [ 3.668077] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.668080] usb usb1: Product: xHCI Host Controller [ 3.668083] usb usb1: Manufacturer: Linux 5.1.2-rj xhci-hcd [ 3.668085] usb usb1: SerialNumber: f10f0000.usb3 [ 3.673576] ata3: SATA link down (SStatus 0 SControl 300) [ 3.701512] ata4: SATA link down (SStatus 0 SControl 300) [ 3.701649] hub 1-0:1.0: USB hub found [ 3.710726] hub 1-0:1.0: 1 port detected [ 3.714814] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 3.720167] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 3.727697] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed [ 3.734207] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.742395] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.01 [ 3.750703] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.757962] usb usb2: Product: xHCI Host Controller [ 3.762860] usb usb2: Manufacturer: Linux 5.1.2-rj xhci-hcd [ 3.768460] usb usb2: SerialNumber: f10f0000.usb3 [ 3.773387] hub 2-0:1.0: USB hub found [ 3.777165] hub 2-0:1.0: 1 port detected [ 3.781417] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 3.786761] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 3 [ 3.794341] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010 [ 3.803632] xhci-hcd f10f8000.usb3: irq 43, io mem 0xf10f8000 [ 3.809556] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.01 [ 3.817872] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.825126] usb usb3: Product: xHCI Host Controller [ 3.830030] usb usb3: Manufacturer: Linux 5.1.2-rj xhci-hcd [ 3.835626] usb usb3: SerialNumber: f10f8000.usb3 [ 3.840565] hub 3-0:1.0: USB hub found [ 3.844344] hub 3-0:1.0: 1 port detected [ 3.848429] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 3.853771] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 3.861304] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed [ 3.867807] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.875983] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.01 [ 3.884293] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.891552] usb usb4: Product: xHCI Host Controller [ 3.896450] usb usb4: Manufacturer: Linux 5.1.2-rj xhci-hcd [ 3.902051] usb usb4: SerialNumber: f10f8000.usb3 [ 3.906969] hub 4-0:1.0: USB hub found [ 3.910757] hub 4-0:1.0: 1 port detected [ 3.915198] armada38x-rtc f10a3800.rtc: setting system clock to 2019-05-21T10:04:06 UTC (1558433046) [ 3.924627] v5.0-sata1: supplied by pwr_en_sata1 [ 3.929310] v12.0-sata0: supplied by pwr_en_sata1 [ 3.934072] v12.0-sata0: disabling [ 3.937489] v5.0-sata1: disabling [ 3.940835] v12.0-sata0: disabling [ 3.944549] Waiting 20 sec before mounting root device... [ 4.117815] ata5: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 4.124769] ata5.00: ATA-9: ST2000VN004-2E4164, SC60, max UDMA/133 [ 4.130987] ata5.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 32) [ 4.138527] ata5.00: configured for UDMA/133 [ 4.153088] scsi 4:0:0:0: Direct-Access ATA ST2000VN004-2E41 SC60 PQ: 0 ANSI: 5 [ 4.161672] sd 4:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB) [ 4.169692] sd 4:0:0:0: [sda] 4096-byte physical blocks [ 4.174969] sd 4:0:0:0: [sda] Write Protect is off [ 4.179832] sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.263537] sda: sda1 [ 4.266525] sd 4:0:0:0: [sda] Attached SCSI removable disk [ 24.177789] md: Waiting for all devices to be available before autodetect [ 24.184607] md: If you don't use raid, use raid=noautodetect [ 24.190706] md: Autodetecting RAID arrays. [ 24.194821] md: autorun ... [ 24.197624] md: ... autorun DONE. [ 24.261443] random: fast init done [ 24.509261] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 24.516989] VFS: Mounted root (ext4 filesystem) readonly on device 8:1. [ 24.570161] devtmpfs: mounted [ 24.574409] Freeing unused kernel memory: 1024K [ 24.579258] Checked W+X mappings: passed, no W+X pages found [ 24.584943] Run /sbin/init as init process INIT: version 2.93 booting [info] Using makefile-style concurrent boot in runlevel S. ERROR: could not open /proc/stat: No such file or directory findfs: unable to resolve 'LABEL=rootfs' [warn] Files under mount point '/run' will be hidden. ... (warning). [ ok ] Starting hotplug events dispatcher: systemd-udevd. [ ok ] Synthesizing the initial hotplug events (subsystems)...done. [ ok ] Synthesizing the initial hotplug events (devices)...done. [....] Waiting for /dev to be fully populated...[ 26.706218] systemd-udevd[1715]: Using default interface naming scheme 'v240'. [ 26.719484] systemd-udevd[1715]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 26.733541] systemd-udevd[1715]: Could not generate persistent MAC address for eth0: No such file or directory [ 26.758303] sd 4:0:0:0: Attached scsi generic sg0 type 0 [ 26.818305] systemd-udevd[1703]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 26.818401] systemd-udevd[1708]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 26.830344] systemd-udevd[1705]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 26.852648] systemd-udevd[1703]: Could not generate persistent MAC address for ip6tnl0: No such file or directory done. [ ok ] Setting hostname to 'debian'...done. [ ok ] Activating swap:. [ 28.056542] EXT4-fs (sda1): re-mounted. Opts: (null) [....] Will now check root file system:fsck from util-linux 2.33.1 [/sbin/fsck.ext4 (1) -- /] fsck.ext4 -y -C0 /dev/sda1 e2fsck 1.44.5 (15-Dec-2018) rootfs: clean, 44766/122093568 files, 8160840/488347392 blocks . ok [ 30.231853] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [info] Will now check all file systems. fsck from util-linux 2.33.1 Checking all file systems. LABEL=rootfs is mounted [ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. [ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done. [ ok . [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Starting Setting kernel variables: sysctl. [....] Initializing random number generator...[ 31.266159] random: dd: uninitialized urandom read (512 bytes read) done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ [ 31.631652] mvneta f1070000.ethernet eth0: PHY [f1072004.mdio-mii:01] driver [Marvell 88E1510] [ 31.640560] mvneta f1070000.ethernet eth0: configuring for phy/sgmii link mode Listening on LPF/eth0/6e:ac:5c:e0:b6:90 Sending on LPF/eth0/6e:ac:5c:e0:b6:90 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6 [ 35.778024] mvneta f1070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 35.785905] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9 DHCPOFFER of 192.168.1.243 from 192.168.1.2 DHCPREQUEST for 192.168.1.243 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.1.243 from 192.168.1.2 [ 41.190854] random: mktemp: uninitialized urandom read (6 bytes read) invoke-rc.d: could not determine current runlevel [ 41.296476] random: crng init done bound to 192.168.1.243 -- renewal in 1351 seconds. done. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [ ok ] Starting periodic command scheduler: cron. [ ok ] Starting system message bus: dbus. [ ok ] Starting fan speed regulator: fancontrol. [ ok ] Starting MD monitoring service: mdadm --monitor. [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Running local boot scripts (/etc/rc.local). Debian GNU/Linux 10 debian ttyS0 debian login:
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 05:18AM |
Registered: 5 years ago Posts: 257 |
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 05:29AM |
Admin Registered: 14 years ago Posts: 19,317 |
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 05:35AM |
Registered: 5 years ago Posts: 257 |
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 05:41AM |
Admin Registered: 14 years ago Posts: 19,317 |
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 05:45AM |
Registered: 5 years ago Posts: 257 |
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 05:49AM |
Admin Registered: 14 years ago Posts: 19,317 |
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 05:03PM |
Registered: 5 years ago Posts: 257 |
root@debian:~# cat armada-385-synology-rs816-v12.dtb >> uInitrd root@debian:~# dd if=zImage of=/dev/sda bs=1M seek=10 4+1 records in 4+1 records out 4841504 bytes (4.8 MB, 4.6 MiB) copied, 0.0582581 s, 83.1 MB/s root@debian:~# dd if=uInitrd of=/dev/sda bs=1M seek=20 9+1 records in 9+1 records out 9897071 bytes (9.9 MB, 9.4 MiB) copied, 0.0764092 s, 130 MB/s
Press Ctrl+C to abort autoboot in 3 second Marvell>> <INTERRUPT> Marvell>> scsi init AHCI init for unit0 Target spinup took 0 ms. SATA link 1 timeout. SATA link 0 timeout. SATA link 1 timeout. SATA link 2 timeout. SATA link 3 timeout. AHCI 0001.0000 32 slots 4 ports 6 Gbps 0xf impl SATA mode flags: 64bit ncq led only pmp fbss pio slum part sxs scanning bus for devices... Device 0: (0:0) Vendor: ATA Prod.: ST2000VN004-2E41 Rev: SC60 Type: Hard Disk Capacity: 1907729.0 MB = 1863.0 GB (3907029168 x 512) Found 1 device(s). Marvell>> scsi device 0 SCSI device 0: Device 0: (0:0) Vendor: ATA Prod.: ST2000VN004-2E41 Rev: SC60 Type: Hard Disk Capacity: 1907729.0 MB = 1863.0 GB (3907029168 x 512) ... is now current device
Marvell>> scsi read 0x40000 0x5000 0x2F00 SCSI read: device 0 block # 20480, count 12032 ... 12032 blocks read: OK Marvell>> scsi read 0x2100000 0xA000 0x4F00 SCSI read: device 0 block # 40960, count 20224 ... 20224 blocks read: OK
Marvell>> imi 0x2100000 ## Checking Image at 02100000 ... Legacy image found Image Name: initramfs-5.1.2-rj Created: 2019-05-19 6:32:55 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9878742 Bytes = 9.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Marvell>> imi ## Checking Image at 02000000 ... Unknown image format!
Marvell>> bootm Wrong Image Format for bootm command ERROR: can't get kernel image!
mkimage -A arm -O linux -T kernel -C none -a 0x00000000 -e 0x00000000 -n "kernel-5.1.2-rj" -d zImage uImage
dd if=uImage of=/dev/sda bs=1M seek=10
Marvell>> scsi init AHCI init for unit0 Target spinup took 0 ms. SATA link 1 timeout. SATA link 0 timeout. SATA link 1 timeout. SATA link 2 timeout. SATA link 3 timeout. AHCI 0001.0000 32 slots 4 ports 6 Gbps 0xf impl SATA mode flags: 64bit ncq led only pmp fbss pio slum part sxs scanning bus for devices... Device 0: (0:0) Vendor: ATA Prod.: ST2000VN004-2E41 Rev: SC60 Type: Hard Disk Capacity: 1907729.0 MB = 1863.0 GB (3907029168 x 512) Found 1 device(s). Marvell>> scsi device 0 SCSI device 0: Device 0: (0:0) Vendor: ATA Prod.: ST2000VN004-2E41 Rev: SC60 Type: Hard Disk Capacity: 1907729.0 MB = 1863.0 GB (3907029168 x 512) ... is now current device Marvell>> scsi read 0x40000 0x5000 0x2F00 SCSI read: device 0 block # 20480, count 12032 ... 12032 blocks read: OK Marvell>> scsi read 0x2100000 0xA000 0x4F00 SCSI read: device 0 block # 40960, count 20224 ... 20224 blocks read: OK Marvell>> imi ## Checking Image at 02000000 ... Unknown image format!
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 06:38PM |
Admin Registered: 14 years ago Posts: 19,317 |
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 06:40PM |
Admin Registered: 14 years ago Posts: 19,317 |
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 06:47PM |
Admin Registered: 14 years ago Posts: 19,317 |
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 07:12PM |
Registered: 5 years ago Posts: 257 |
scsi init setenv ipaddr 192.168.1.250 setenv serverip 192.168.1.2 setenv load_dtb_addr 0x1000000 setenv load_initrd_addr 0x3000000 setenv load_image_addr 0x02000000 setenv load_image 'echo loading zImage from raw HDD ...; scsi device 0; scsi read 0x40000 0x5000 0x2F00 $load_image_addr' setenv load_initrd 'echo loading uInitrd from raw HDD ...; scsi device 0; scsi read 0x2100000 0xA000 0x4F00 $load_initrd_addr' setenv load_dtb 'echo loading DTB from tftpserver ...; tftpboot $load_dtb_addr armada-385-synology-rs816-v12.dtb' setenv set_bootargs 'setenv bootargs "console=ttyS0,115200 root=/dev/sda1 rootdelay=20 $mtdparts earlyprintk=serial"' setenv bootcmd_exec 'echo Booting Debian . . .; run set_bootargs; setenv fdt_skip_update yes; setenv initrd_high 0xffffffff; run load_image; run load_initrd; run load_dtb; bootz $load_image_addr $load_initrd_addr $load_dtb_addr' setenv bootcmd 'run bootcmd_exec; run bootspi'
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 07:32PM |
Registered: 5 years ago Posts: 257 |
Quote
Note: the imi command only works with uInitrd or uImage.
mkimage -A arm -O linux -T kernel -C none -a 0x00000000 -e 0x00000000 -n "kernel-5.1.2-rj" -d zImage uImage
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 08:15PM |
Registered: 5 years ago Posts: 257 |
Marvell>> scsi init AHCI init for unit0 Target spinup took 0 ms. SATA link 1 timeout. SATA link 0 timeout. SATA link 1 timeout. SATA link 2 timeout. SATA link 3 timeout. AHCI 0001.0000 32 slots 4 ports 6 Gbps 0xf impl SATA mode flags: 64bit ncq led only pmp fbss pio slum part sxs scanning bus for devices... Device 0: (0:0) Vendor: ATA Prod.: ST2000VN004-2E41 Rev: SC60 Type: Hard Disk Capacity: 1907729.0 MB = 1863.0 GB (3907029168 x 512) Found 1 device(s). Marvell>> setenv ipaddr 192.168.1.250 Marvell>> setenv serverip 192.168.1.2 Marvell>> setenv load_dtb_addr 0x1000000 Marvell>> setenv load_initrd_addr 0x3000000 Marvell>> setenv load_image_addr 0x02000000 Marvell>> setenv load_image 'echo loading zImage from raw HDD ...; scsi device 0; scsi read 0x40000 0x5000 0x2F00 $load_image_addr' Marvell>> setenv load_initrd 'echo loading uInitrd from raw HDD ...; scsi device 0; scsi read 0x2100000 0xA000 0x4F00 $load_initrd_addr' Marvell>> setenv load_dtb 'echo loading DTB from tftpserver ...; tftpboot $load_dtb_addr armada-385-synology-rs816-v12.dtb' Marvell>> setenv set_bootargs 'setenv bootargs "console=ttyS0,115200 root=/dev/sda1 rootdelay=20 $mtdparts earlyprintk=serial"' Marvell>> setenv bootcmd_exec 'echo Booting Debian . . .; run set_bootargs; setenv fdt_skip_update yes; setenv initrd_high 0xffffffff; run load_image; run load_initrd; run load_dtb; bootz $load_image_addr $load_initrd_addr $load_dtb_addr' Marvell>> setenv bootcmd 'run bootcmd_exec; run bootspi' Marvell>> boot Booting Debian . . . loading zImage from raw HDD ... SCSI device 0: Device 0: (0:0) Vendor: ATA Prod.: ST2000VN004-2E41 Rev: SC60 Type: Hard Disk Capacity: 1907729.0 MB = 1863.0 GB (3907029168 x 512) ... is now current device scsi - SCSI sub-system Usage: scsi reset - reset SCSI controller scsi info - show available SCSI devices scsi scan - (re-)scan SCSI bus scsi device [dev] - show or set current device scsi part [dev] - print partition table of one or all SCSI devices scsi read addr blk# cnt - read `cnt' blocks starting at block `blk#' to memory address `addr' scsi write addr blk# cnt - write `cnt' blocks starting at block `blk#' from memory address `addr' loading uInitrd from raw HDD ... SCSI device 0: Device 0: (0:0) Vendor: ATA Prod.: ST2000VN004-2E41 Rev: SC60 Type: Hard Disk Capacity: 1907729.0 MB = 1863.0 GB (3907029168 x 512) ... is now current device scsi - SCSI sub-system Usage: scsi reset - reset SCSI controller scsi info - show available SCSI devices scsi scan - (re-)scan SCSI bus scsi device [dev] - show or set current device scsi part [dev] - print partition table of one or all SCSI devices scsi read addr blk# cnt - read `cnt' blocks starting at block `blk#' to memory address `addr' scsi write addr blk# cnt - write `cnt' blocks starting at block `blk#' from memory address `addr' loading DTB from tftpserver ... Using egiga0 device TFTP from server 192.168.1.2; our IP address is 192.168.1.250 Filename 'armada-385-synology-rs816-v12.dtb'. Load address: 0x1000000 Loading: ## 712.9 KiB/s done Bytes transferred = 18265 (4759 hex) Bad Linux ARM zImage magic! SF: Detected N25Q64 with page size 64 KiB, total 8 MiB
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 09:04PM |
Registered: 5 years ago Posts: 257 |
SCSI read: device 0 block # 20480, count 33554432 ...
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 09:23PM |
Admin Registered: 14 years ago Posts: 19,317 |
Quote
I will use the SPI images as you suggest but to make sure I understand you correctly you mean the ones ending *.kwb ?
Quote
Bad Linux ARM zImage magic!
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 09:49PM |
Registered: 5 years ago Posts: 257 |
root@debian:~# cd /boot root@debian:/boot# ls -lh zImage -rwxr-xr-x 1 root root 4.7M May 19 14:08 zImage root@debian:/boot# ls -lh uInitrd -rw-r--r-- 1 root root 9.5M May 19 14:32 uInitrd root@debian:/boot# dd if=zImage of=/dev/sda bs=1M seek=10 4+1 records in 4+1 records out 4841504 bytes (4.8 MB, 4.6 MiB) copied, 0.1255 s, 38.6 MB/s root@debian:/boot# dd if=uInitrd of=/dev/sda bs=1M seek=20 9+1 records in 9+1 records out 9878806 bytes (9.9 MB, 9.4 MiB) copied, 0.125786 s, 78.5 MB/s
Marvell>> <INTERRUPT> Marvell>> scsi init AHCI init for unit0 Target spinup took 0 ms. SATA link 1 timeout. SATA link 0 timeout. SATA link 1 timeout. SATA link 2 timeout. SATA link 3 timeout. AHCI 0001.0000 32 slots 4 ports 6 Gbps 0xf impl SATA mode flags: 64bit ncq led only pmp fbss pio slum part sxs scanning bus for devices... Device 0: (0:0) Vendor: ATA Prod.: ST2000VN004-2E41 Rev: SC60 Type: Hard Disk Capacity: 1907729.0 MB = 1863.0 GB (3907029168 x 512) Found 1 device(s). Marvell>> setenv ipaddr 192.168.1.250 Marvell>> setenv serverip 192.168.1.2 Marvell>> setenv load_dtb_addr 0x1000000 Marvell>> setenv load_initrd_addr 0x3000000 Marvell>> setenv load_image_addr 0x02000000 Marvell>> setenv load_image 'echo loading zImage from raw HDD ...; scsi device 0; scsi read 0x40000 0x5000 $load_image_addr' Marvell>> setenv load_initrd 'echo loading uInitrd from raw HDD ...; scsi device 0; scsi read 0x2100000 0xA000 $load_initrd_addr' Marvell>> setenv load_dtb 'echo loading DTB from tftpserver ...; tftpboot $load_dtb_addr armada-385-synology-rs816-v12.dtb' Marvell>> setenv set_bootargs 'setenv bootargs "console=ttyS0,115200 root=/dev/sda1 rootdelay=20 $mtdparts earlyprintk=serial"' Marvell>> setenv bootcmd_exec 'echo Booting Debian . . .; run set_bootargs; setenv fdt_skip_update yes; setenv initrd_high 0xffffffff; run load_image; run load_initrd; run load_dtb; bootz $load_image_addr $load_initrd_addr $load_dtb_addr' Marvell>> setenv bootcmd 'run bootcmd_exec; run bootspi' Marvell>> boot Booting Debian . . . loading zImage from raw HDD ... SCSI device 0: Device 0: (0:0) Vendor: ATA Prod.: ST2000VN004-2E41 Rev: SC60 Type: Hard Disk Capacity: 1907729.0 MB = 1863.0 GB (3907029168 x 512) ... is now current device SCSI read: device 0 block # 20480, count 33554432 ...
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 10:13PM |
Admin Registered: 14 years ago Posts: 19,317 |
Quote
https://forum.doozan.com/read.php?2,70294,70794#msg-70794
/kernels# dd if=uImage of=/dev/sdc bs=1MiB seek=10
3+1 records in
3+1 records out
4171272 bytes (4.2 MB, 4.0 MiB) copied, 3.1455 s, 1.3 MB/s
.....
Marvell>> setenv bootcmd 'ide device 1; ide read 0x40000 0x5000 0x2000; ide read 0x2100000 0xA000 0x4F00; bootm 0x40000 0x2100000'
dd if=zImage of=/dev/sda bs=1MiB seek=10
setenv load_image 'echo loading zImage from raw HDD ...; scsi device 0; scsi read $load_image_addr 0x5000 0x2000
Quote
u-boot help
scsi read addr blk# cnt - read `cnt' blocks starting at block `blk#'
to memory address `addr'
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 10:45PM |
Registered: 5 years ago Posts: 257 |
root@debian:~# dd if=/dev/zero of=/dev/sda bs=1M seek=10 count=60 60+0 records in 60+0 records out 62914560 bytes (63 MB, 60 MiB) copied, 0.139173 s, 452 MB/s root@debian:~# cd /boot root@debian:/boot# dd if=zImage of=/dev/sda bs=1MiB seek=10 4+1 records in 4+1 records out 4841504 bytes (4.8 MB, 4.6 MiB) copied, 0.0806912 s, 60.0 MB/s
Quote
scsi read addr blk# cnt - read `cnt' blocks starting at block `blk#'
to memory address `addr'
Marvell>> <INTERRUPT> Marvell>> scsi init AHCI init for unit0 Target spinup took 0 ms. SATA link 1 timeout. SATA link 0 timeout. SATA link 1 timeout. SATA link 2 timeout. SATA link 3 timeout. AHCI 0001.0000 32 slots 4 ports 6 Gbps 0xf impl SATA mode flags: 64bit ncq led only pmp fbss pio slum part sxs scanning bus for devices... Device 0: (0:0) Vendor: ATA Prod.: ST2000VN004-2E41 Rev: SC60 Type: Hard Disk Capacity: 1907729.0 MB = 1863.0 GB (3907029168 x 512) Found 1 device(s). Marvell>> setenv ipaddr 192.168.1.250 Marvell>> setenv serverip 192.168.1.2 Marvell>> setenv load_dtb_addr 0x1000000 Marvell>> setenv load_image_addr 0x02000000 Marvell>> setenv load_image 'echo loading zImage from raw HDD ...; scsi device 0; scsi read $load_image_addr 0x5000 0x2000' Marvell>> setenv load_dtb 'echo loading DTB from tftpserver ...; tftpboot $load_dtb_addr armada-385-synology-rs816-v12.dtb' Marvell>> setenv set_bootargs 'setenv bootargs "console=ttyS0,115200 root=/dev/sda1 rootdelay=20 $mtdparts earlyprintk=serial"' Marvell>> setenv bootcmd_exec 'echo Booting Debian . . .; run set_bootargs; setenv fdt_skip_update yes; setenv initrd_high 0xffffffff; run load_image; run load_dtb; bootz $load_image_addr $load_dtb_addr' Marvell>> setenv bootcmd 'run bootcmd_exec; run bootspi' Marvell>> boot Booting Debian . . . loading zImage from raw HDD ... SCSI device 0: Device 0: (0:0) Vendor: ATA Prod.: ST2000VN004-2E41 Rev: SC60 Type: Hard Disk Capacity: 1907729.0 MB = 1863.0 GB (3907029168 x 512) ... is now current device SCSI read: device 0 block # 20480, count 8192 ... 8192 blocks read: OK loading DTB from tftpserver ... Using egiga0 device TFTP from server 192.168.1.2; our IP address is 192.168.1.250 Filename 'armada-385-synology-rs816-v12.dtb'. Load address: 0x1000000 Loading: ## 556.6 KiB/s done Bytes transferred = 18265 (4759 hex) Wrong Ramdisk Image Format Ramdisk image is corrupt or invalid
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 11:08PM |
Admin Registered: 14 years ago Posts: 19,317 |
cd /boot cp -a uImage uImage.bak ### if there is one then we back it up mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-5.1.2-mvebu-tld-1 -d vmlinuz-5.1.2-mvebu-tld-1 uImage
setenv bootcmd_exec 'echo Booting Debian . . .; run set_bootargs; setenv fdt_skip_update yes; setenv initrd_high 0xffffffff; run load_image; run load_dtb; bootm $load_image_addr - $load_dtb_addr''
Re: Debian on Synology RS816 (Armada 385) May 21, 2019 11:28PM |
Registered: 5 years ago Posts: 257 |
root@debian:~# cd /boot 00008000 -n Linux-5.1.2-rj -d vmlinuz-5.1.2-rj uImage-C none -a 0x00008000 -e 0x0 Image Name: Linux-5.1.2-rj Created: Wed May 22 12:15:51 2019 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4841504 Bytes = 4728.03 KiB = 4.62 MiB Load Address: 00008000 Entry Point: 00008000 root@debian:/boot# dd if=uImage of=/dev/sda bs=1MiB seek=10 4+1 records in 4+1 records out 4841568 bytes (4.8 MB, 4.6 MiB) copied, 0.0191701 s, 253 MB/s
Marvell>> <INTERRUPT> Marvell>> scsi init AHCI init for unit0 Target spinup took 0 ms. SATA link 1 timeout. SATA link 0 timeout. SATA link 1 timeout. SATA link 2 timeout. SATA link 3 timeout. AHCI 0001.0000 32 slots 4 ports 6 Gbps 0xf impl SATA mode flags: 64bit ncq led only pmp fbss pio slum part sxs scanning bus for devices... Device 0: (0:0) Vendor: ATA Prod.: ST2000VN004-2E41 Rev: SC60 Type: Hard Disk Capacity: 1907729.0 MB = 1863.0 GB (3907029168 x 512) Found 1 device(s). Marvell>> setenv ipaddr 192.168.1.250 Marvell>> setenv serverip 192.168.1.2 Marvell>> setenv load_dtb_addr 0x1000000 Marvell>> setenv load_image_addr 0x02000000 Marvell>> setenv load_image 'echo loading zImage from raw HDD ...; scsi device 0; scsi read $load_image_addr 0x5000 0x2000' Marvell>> setenv load_dtb 'echo loading DTB from tftpserver ...; tftpboot $load_dtb_addr armada-385-synology-rs816-v12.dtb' Marvell>> setenv set_bootargs 'setenv bootargs "console=ttyS0,115200 root=/dev/sda1 rootdelay=20 $mtdparts earlyprintk=serial"' Marvell>> setenv bootcmd_exec 'echo Booting Debian . . .; run set_bootargs; setenv fdt_skip_update yes; setenv initrd_high 0xffffffff; run load_image; run load_dtb; bootm $load_image_addr - $load_dtb_addr' Marvell>> setenv bootcmd 'run bootcmd_exec; run bootspi' Marvell>> boot Booting Debian . . . loading zImage from raw HDD ... SCSI device 0: Device 0: (0:0) Vendor: ATA Prod.: ST2000VN004-2E41 Rev: SC60 Type: Hard Disk Capacity: 1907729.0 MB = 1863.0 GB (3907029168 x 512) ... is now current device SCSI read: device 0 block # 20480, count 8192 ... 8192 blocks read: OK loading DTB from tftpserver ... Using egiga0 device TFTP from server 192.168.1.2; our IP address is 192.168.1.250 Filename 'armada-385-synology-rs816-v12.dtb'. Load address: 0x1000000 Loading: ## 1.1 MiB/s done Bytes transferred = 18265 (4759 hex) ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-5.1.2-rj Created: 2019-05-22 4:15:51 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4841504 Bytes = 4.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... Bad Data CRC ERROR: can't get kernel image! SF: Detected N25Q64 with page size 64 KiB, total 8 MiB Wrong Image Format for bootm command ERROR: can't get kernel image! Marvell>>
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-5.1.2-rj -d vmlinuz-5.1.2-rj uImage