Zyxel 310. No ethernet since the 4.20 kernel on Arch - is it working in Debian?
Posted by arti74
|
Re: Zyxel 310. No ethernet since the 4.20 kernel on Arch - is it working in Debian? February 26, 2019 04:41AM |
Registered: 7 years ago Posts: 21 |
Sorry for the late reply!
4.16.1 and 4.19.0: had no network at first, left Ethernet LED flashing, did modprobe r8169, LEDs out but the network went up!
4.19.0 ->
4.20.6-kirkwood-tld-2: no network, right LED flashing (huh?) modprobe failure...
No clue as to why it's not auto-detected on 4.19/16!
---
NSA310s, NSA310, C.H.I.P, Banana Pi, Orange Pi PC & Zero, RPI 1,2Bx8
4.16.1 and 4.19.0: had no network at first, left Ethernet LED flashing, did modprobe r8169, LEDs out but the network went up!
[ 66.296987] libphy: r8169: probed [ 66.308621] r8169 0000:01:00.0 eth0: RTL8168d/8111d, 00:00:00:00:00:30, XID 283000c0, IRQ 38 [ 66.317106] r8169 0000:01:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] mark@nsa310a:~$ [ 66.373085] r8169 0000:01:00.0 enp1s0: renamed from eth0 [ 66.961880] RTL8211B Gigabit Ethernet r8169-100:00: attached PHY driver [RTL8211B Gigabit Ethernet] (mii_bus:phy_addr=r8169-100:00, irq=IGNORE) [ 67.159336] r8169 0000:01:00.0 enp1s0: Link is Down [ 67.164381] IPv6: ADDRCONF(NETDEV_UP): enp1s0: link is not ready [ 69.420000] r8169 0000:01:00.0 enp1s0: Link is Up - 1Gbps/Full - flow control rx/tx [ 69.427748] IPv6: ADDRCONF(NETDEV_CHANGE): enp1s0: link becomes ready
4.19.0 ->
mark@nsa310a:~$ sudo ethtool enp1s0
Settings for enp1s0:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Link partner advertised pause frame use: Symmetric
Link partner advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: MII
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: pumbg
Wake-on: g
Current message level: 0x00000033 (51)
drv probe ifdown ifup
Link detected: yes
4.20.6-kirkwood-tld-2: no network, right LED flashing (huh?) modprobe failure...
mark@nsa310a:~$ sudo modprobe r8169 [ 65.142387] r8169 0000:01:00.0 (unnamed net_device) (uninitialized): rtl_phyar_cond == 0 (loop: 20, delay: 25). [ 65.179047] r8169: probe of 0000:01:00.0 failed with error -5
No clue as to why it's not auto-detected on 4.19/16!
---
NSA310s, NSA310, C.H.I.P, Banana Pi, Orange Pi PC & Zero, RPI 1,2Bx8
|
Re: Zyxel 310. No ethernet since the 4.20 kernel on Arch - is it working in Debian? February 26, 2019 02:54PM |
Admin Registered: 13 years ago Posts: 18,900 |
Arti,
I saw you have tested the test case 1. That has confirmed what I would like to see: running the latest kernel, unplug/replug the cable still does not bring the card up for detection. Let me write another test below.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 02/26/2019 03:05PM by bodhi.
I saw you have tested the test case 1. That has confirmed what I would like to see: running the latest kernel, unplug/replug the cable still does not bring the card up for detection. Let me write another test below.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 02/26/2019 03:05PM by bodhi.
|
Re: Zyxel 310. No ethernet since the 4.20 kernel on Arch - is it working in Debian? February 26, 2019 03:06PM |
Admin Registered: 13 years ago Posts: 18,900 |
mpmc,
Please repeat test 1. You've used the wrong version :) (tld-2 is to be trashed, not usable! )
1. Go back to kernel linux-4.20.6-kirkwood-tld-1. Reboot and do these following.
Unplug the ethernet cable, and replug. What are dmesg logs, if any, when you do that?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Please repeat test 1. You've used the wrong version :) (tld-2 is to be trashed, not usable! )
1. Go back to kernel linux-4.20.6-kirkwood-tld-1. Reboot and do these following.
Unplug the ethernet cable, and replug. What are dmesg logs, if any, when you do that?
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Zyxel 310. No ethernet since the 4.20 kernel on Arch - is it working in Debian? February 26, 2019 03:14PM |
Admin Registered: 13 years ago Posts: 18,900 |
Please try this.
1. Go back to the working kernel linux-4.19.x. Reboot. Login and turn off WOL.
2. Reboot and check WOL status to make sure it is off.
3. Go back to the latest kernel 4.20.x. Reboot. Observer serial console log to see if there is any change in network card behavior.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
1. Go back to the working kernel linux-4.19.x. Reboot. Login and turn off WOL.
ethtool -s eth0 wol d
2. Reboot and check WOL status to make sure it is off.
ethtool eth0
3. Go back to the latest kernel 4.20.x. Reboot. Observer serial console log to see if there is any change in network card behavior.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Zyxel 310. No ethernet since the 4.20 kernel on Arch - is it working in Debian? February 26, 2019 03:41PM |
Registered: 7 years ago Posts: 21 |
As requested :)
The paste is too large -> Pastebinned here for your enjoyment [password is bodhi]
---
NSA310s, NSA310, C.H.I.P, Banana Pi, Orange Pi PC & Zero, RPI 1,2Bx8
The paste is too large -> Pastebinned here for your enjoyment [password is bodhi]
---
NSA310s, NSA310, C.H.I.P, Banana Pi, Orange Pi PC & Zero, RPI 1,2Bx8
|
Re: Zyxel 310. No ethernet since the 4.20 kernel on Arch - is it working in Debian? February 26, 2019 04:17PM |
Admin Registered: 13 years ago Posts: 18,900 |
So that was not because of the WOL change in mainline, after all.
It is strange that now you don't see the module starts early in dmesg with kernel 4.20.x like before. It is supposed to be in-kernel module. Not something you have to modprobe.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
It is strange that now you don't see the module starts early in dmesg with kernel 4.20.x like before. It is supposed to be in-kernel module. Not something you have to modprobe.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Zyxel 310. No ethernet since the 4.20 kernel on Arch - is it working in Debian? February 26, 2019 04:26PM |
Registered: 6 years ago Posts: 45 |
Did those all steps, with same result like @mpmc
And modprobing r8169 module - no effect:
Edited 1 time(s). Last edit at 02/26/2019 04:27PM by arti74.
And modprobing r8169 module - no effect:
[rtorrent@zyxel ~]$ sudo modprobe r8169 [rtorrent@zyxel ~]$ lsmod Module Size Used by adt7475 18222 0 hwmon_vid 2046 1 adt7475 hwmon 11907 1 adt7475 marvell_cesa 31895 0 i2c_mv64xxx 8110 0 nfsd 274299 13 ip_tables 11147 0 x_tables 16467 1 ip_tables ipv6 410562 50No changes in dmesg, just the same error during start-up.
[rtorrent@zyxel ~]$ dmesg | grep r816 [ 2.019355] r8169 0000:01:00.0: enabling device (0140 -> 0143) [ 2.026039] r8169 0000:01:00.0 (unnamed net_device) (uninitialized): rtl_phyar_cond == 0 (loop: 20, delay: 25). [ 2.036418] r8169: probe of 0000:01:00.0 failed with error -5
Edited 1 time(s). Last edit at 02/26/2019 04:27PM by arti74.
|
Re: Zyxel 310. No ethernet since the 4.20 kernel on Arch - is it working in Debian? February 26, 2019 10:08PM |
Admin Registered: 13 years ago Posts: 18,900 |
mpmc,
How about this. Go back to the kernel linux-4.20.6-kirkwood-tld-1. Reboot. Login with serial console.
Back up the current version
/lib/modules/4.20.6-kirkwood-tld-1/kernel/drivers/net/ethernet/realtek/r8169.ko
Copy this attached version of r8169 to that folder.
And modprobe r8169.
My bad: I've just checked: kernel 4.20.6-kirkwood-tld-1 was built with r8169 as module (not in-kernel). That explained why it was not up early, and you have to modprobe it.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 3 time(s). Last edit at 02/26/2019 10:15PM by bodhi.
How about this. Go back to the kernel linux-4.20.6-kirkwood-tld-1. Reboot. Login with serial console.
Back up the current version
/lib/modules/4.20.6-kirkwood-tld-1/kernel/drivers/net/ethernet/realtek/r8169.ko
Copy this attached version of r8169 to that folder.
And modprobe r8169.
My bad: I've just checked: kernel 4.20.6-kirkwood-tld-1 was built with r8169 as module (not in-kernel). That explained why it was not up early, and you have to modprobe it.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 3 time(s). Last edit at 02/26/2019 10:15PM by bodhi.
|
Re: Zyxel 310. No ethernet since the 4.20 kernel on Arch - is it working in Debian? February 27, 2019 12:15AM |
Registered: 7 years ago Posts: 21 |
As requested :)
Not sure why that formatting screwed up like that!
---
NSA310s, NSA310, C.H.I.P, Banana Pi, Orange Pi PC & Zero, RPI 1,2Bx8
Edited 1 time(s). Last edit at 02/27/2019 12:38AM by mpmc.
nsa310a login: mark
Password:
Last login: Tue Feb 26 21:34:28 GMT 2019 on ttyS0
Linux nsa310a 4.20.6-kirkwood-tld-1 #1 PREEMPT Thu Jan 31 21:41:45 PST 2019 armv 5tel
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
sark@nsa310a:~$ sudo -
[sudo] password for mark:
root@nsa310a:/home/mark# [ 55.138963] usb 1-1.2: USB disconnect, device number 3
root@nsa310a:/home/mark#
root@nsa310a:/home/mark#
root@nsa310a:/home/mark# [ 112.558913] usb 1-1.2: new high-speed USB device num ber 4 using orion-ehci
[ 112.709839] usb 1-1.2: New USB device found, idVendor=0781, idProduct=5567, b cdDevice= 1.26
[ 112.718251] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber =3
[ 112.727255] usb 1-1.2: Product: Cruzer Blade
[ 112.732559] usb 1-1.2: Manufacturer: SanDisk
[ 112.736881] usb 1-1.2: SerialNumber: 4C530299941204110041
[ 112.749702] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 112.757788] scsi host2: usb-storage 1-1.2:1.0
[ 113.770440] scsi 2:0:0:0: Direct-Access SanDisk Cruzer Blade 1.26 PQ : 0 ANSI: 6
[ 113.786140] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 113.792402] sd 2:0:0:0: [sdb] 15633408 512-byte logical blocks: (8.00 GB/7.45 GiB)
[ 113.810651] sd 2:0:0:0: [sdb] Write Protect is off
[ 113.822333] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doe sn't support DPO or FUA
[ 113.865528] sdb: sdb1
[ 113.872521] sd 2:0:0:0: [sdb] Attached SCSI removable disk
root@nsa310a:/home/mark# cd /boot
root@nsa310a:/boot# mkdir /tmp/usb
root@nsa310a:/boot# mount /dev/sdb1 /tmp/usb
[ 144.748705] FAT-fs (sdb1): utf8 is not a recommended IO charset for FAT files ystems, filesystem will be case sensitive!
root@nsa310a:/boot# cd /lib/modules/4.20.6-kirkwood-tld-1/kernel/drivers/net/eth ernet/realtek
root@nsa310a:/lib/modules/4.20.6-kirkwood-tld-1/kernel/drivers/net/ethernet/real tek# ls
r8169.ko
root@nsa310a:/lib/modules/4.20.6-kirkwood-tld-1/kernel/drivers/net/ethernet/real tek# mv r8169.ko r8169.ko.jic
root@nsa310a:/lib/modules/4.20.6-kirkwood-tld-1/kernel/drivers/net/ethernet/real tek# cp /tmp/
.font-unix/
.ICE-unix/
systemd-private-17df8ee5844446f7881539d5b405d6a4-systemd-timesyncd.service-cAeL3 u/
.Test-unix/
usb/
.X11-unix/
.XIM-unix/
root@nsa310a:/lib/modules/4.20.6-kirkwood-tld-1/kernel/drivers/net/ethernet/real tek# cp /tmp/usb/r8169.ko .
root@nsa310a:/lib/modules/4.20.6-kirkwood-tld-1/kernel/drivers/net/ethernet/real tek# ls -lah
total 184K
drwxr-xr-x 2 root root 4.0K Feb 27 06:10 .
drwxr-xr-x 13 root root 4.0K Feb 26 21:32 ..
-rwxr-xr-x 1 root root 85K Feb 27 06:10 r8169.ko
-rw-r--r-- 1 root root 85K Feb 1 08:36 r8169.ko.jic
root@nsa310a:/lib/modules/4.20.6-kirkwood-tld-1/kernel/drivers/net/ethernet/real tek# sudo reboot
Stopping Session c1 of user mark.
....
[ 216.598085] reboot: Restarting system
▒
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE
U-Boot 1.1.4 (Feb 22 2011 - 10:31:35) Marvell version: 3.4.19
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFEE0
Soc: 88F6281 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 10M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (10M - 7M): Done
NAND:128 MB
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Kernel address is 0x4640000.
Streaming disabled
Write allocate disabled
Module 0 is RGMII
Module 1 is TDM
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0, egiga1 [PRIME]
Hit any key to stop autoboot: 0
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
Device 0 @ 0 0:
Model: SAMSUNG HD103SJ Firm: 1AJ10001 Ser#: S246J9GB900 083
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
4442428 bytes read
## Booting image at 00800000 ...
Image Name: Linux-4.20.6-kirkwood-tld-1
Created: 2019-02-26 21:33:34 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4442364 Bytes = 4.2 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
....
[ OK ] Started Update UTMP about System Runlevel Changes.
Debian GNU/Linux 9 nsa310a ttyS0
nsa310a login: mark
Password:
Last login: Wed Feb 27 06:07:57 GMT 2019 on ttyS0
Linux nsa310a 4.20.6-kirkwood-tld-1 #1 PREEMPT Thu Jan 31 21:41:45 PST 2019 armv 5tel
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
mark@nsa310a:~$ sudo modprobe r8169
[sudo] password for mark:
[ 47.350142] r8169: disagrees about version of symbol module_layout
modprobe: ERROR: could not insert 'r8169': Exec format error
mark@nsa310a:~$ cd /lib/modules/4.20.6-kirkwood-tld-1/kernel/drivers/net/etherne t/realtek/
mark@nsa310a:/lib/modules/4.20.6-kirkwood-tld-1/kernel/drivers/net/ethernet/real tek$ ls -lah
total 184K
drwxr-xr-x 2 root root 4.0K Feb 27 06:10 .
drwxr-xr-x 13 root root 4.0K Feb 26 21:32 ..
-rwxr-xr-x 1 root root 85K Feb 27 06:10 r8169.ko
-rw-r--r-- 1 root root 85K Feb 1 08:36 r8169.ko.jic
mark@nsa310a:/lib/modules/4.20.6-kirkwood-tld-1/kernel/drivers/net/ethernet/real tek$ sha512sum *
a0f6fbda0bb00c08d2369e9bb8d50e73e52e1cc9aa66b2d30e22cb6ee3f99336e5fdbf4cccd37b77 8ad28d21379c7a02777f1944f51915d6ea1e5ab854123940 r8169.ko
eb9ae3054026ff33a0a51b85513ae6f1b417ae669fe91ff6c3b4c91f2ffecad8c78aaf4a34bdf209 fe07b0cc48f155c25dcb1f251fdef6e0aa71de583d25cfc5 r8169.ko.jic
mark@nsa310a:/lib/modules/4.20.6-kirkwood-tld-1/kernel/drivers/net/ethernet/real tek$
Not sure why that formatting screwed up like that!
---
NSA310s, NSA310, C.H.I.P, Banana Pi, Orange Pi PC & Zero, RPI 1,2Bx8
Edited 1 time(s). Last edit at 02/27/2019 12:38AM by mpmc.
|
Re: Zyxel 310. No ethernet since the 4.20 kernel on Arch - is it working in Debian? February 27, 2019 02:05AM |
Admin Registered: 13 years ago Posts: 18,900 |
mpmc,
Damn :) that means there were changes in the module interface, too, from older version to the current module version.
Hoping to avoid a bisect, I was just trying a few potential shortcuts. But looks like that is not going to work.
Thank for trying!
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 02/27/2019 02:07AM by bodhi.
Damn :) that means there were changes in the module interface, too, from older version to the current module version.
Hoping to avoid a bisect, I was just trying a few potential shortcuts. But looks like that is not going to work.
Thank for trying!
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 02/27/2019 02:07AM by bodhi.
|
Re: Zyxel 310. No ethernet since the 4.20 kernel on Arch - is it working in Debian? February 27, 2019 02:29AM |
Registered: 7 years ago Posts: 21 |
@bodhi
I wonder if they've fixed it in 5.0? I'd build it myself to see but like I say I tried before and the cross compile just hung on deb unstable
I'm more than happy to test anything else you can think of though!
Cheers!
---
NSA310s, NSA310, C.H.I.P, Banana Pi, Orange Pi PC & Zero, RPI 1,2Bx8
I wonder if they've fixed it in 5.0? I'd build it myself to see but like I say I tried before and the cross compile just hung on deb unstable
I'm more than happy to test anything else you can think of though!
Cheers!
---
NSA310s, NSA310, C.H.I.P, Banana Pi, Orange Pi PC & Zero, RPI 1,2Bx8
|
Re: Zyxel 310. No ethernet since the 4.20 kernel on Arch - is it working in Debian? February 27, 2019 01:25PM |
Admin Registered: 13 years ago Posts: 18,900 |
mpmc Wrote:
-------------------------------------------------------
> @bodhi
>
> I wonder if they've fixed it in 5.0? I'd build it
> myself to see but like I say I tried before and
> the cross compile just hung on deb unstable
>
> I'm more than happy to test anything else you can
> think of though!
>
> Cheers!
Kernel 5.0 will be released in a week. Perhaps we should wait till then.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> @bodhi
>
> I wonder if they've fixed it in 5.0? I'd build it
> myself to see but like I say I tried before and
> the cross compile just hung on deb unstable
>
> I'm more than happy to test anything else you can
> think of though!
>
> Cheers!
Kernel 5.0 will be released in a week. Perhaps we should wait till then.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Zyxel 310. No ethernet since the 4.20 kernel on Arch - is it working in Debian? March 04, 2019 03:33AM |
Registered: 7 years ago Posts: 21 |
bodhi Wrote:
-------------------------------------------------------
> mpmc Wrote:
> -------------------------------------------------------
> > @bodhi
> >
> > I wonder if they've fixed it in 5.0? I'd build
> it
> > myself to see but like I say I tried before and
> > the cross compile just hung on deb unstable
> >
> > I'm more than happy to test anything else you
> can
> > think of though!
> >
> > Cheers!
>
> Kernel 5.0 will be released in a week. Perhaps we
> should wait till then.
I tried 5.0.rc8 unfortunately that still has this issue too.
---
NSA310s, NSA310, C.H.I.P, Banana Pi, Orange Pi PC & Zero, RPI 1,2Bx8
-------------------------------------------------------
> mpmc Wrote:
> -------------------------------------------------------
> > @bodhi
> >
> > I wonder if they've fixed it in 5.0? I'd build
> it
> > myself to see but like I say I tried before and
> > the cross compile just hung on deb unstable
> >
> > I'm more than happy to test anything else you
> can
> > think of though!
> >
> > Cheers!
>
> Kernel 5.0 will be released in a week. Perhaps we
> should wait till then.
I tried 5.0.rc8 unfortunately that still has this issue too.
mark@nsa310a:~$ sudo modprobe r8169 [ 114.935325] r8169 0000:01:00.0 (unnamed net_device) (uninitialized): rtl_phyar_cond == 0 (loop: 20, delay: 25). [ 114.977736] r8169: probe of 0000:01:00.0 failed with error -5 mark@nsa310a:~$ uname -a Linux nsa310a 5.0.0-rc8-tld-1 #1 PREEMPT Fri Mar 1 11:58:42 GMT 2019 armv5tel GNU/Linux
---
NSA310s, NSA310, C.H.I.P, Banana Pi, Orange Pi PC & Zero, RPI 1,2Bx8
|
Re: Zyxel 310. No ethernet since the 4.20 kernel on Arch - is it working in Debian? March 05, 2019 07:47AM |
Registered: 6 years ago Posts: 45 |
|
Re: Zyxel 310. No ethernet since the 4.20 kernel on Arch - is it working in Debian? March 10, 2019 04:54AM |
Registered: 6 years ago Posts: 45 |
|
Re: Zyxel 310. No ethernet since the 4.20 kernel on Arch - is it working in Debian? March 10, 2019 05:43PM |
Admin Registered: 13 years ago Posts: 18,900 |
arti74 Wrote:
-------------------------------------------------------
> Confirmed - kernel
>
Bad news indeed !
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-------------------------------------------------------
> Confirmed - kernel
>
> 5.0.0-1-ARCH #1 PREEMPT Tue Mar 5 05:19:51 UTC > 2019 > >> and exactly the same r8169 "error -5"
Bad news indeed !
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: Zyxel 310. No ethernet since the 4.20 kernel on Arch - is it working in Debian? March 10, 2019 08:36PM |
Registered: 7 years ago Posts: 21 |
Would be interesting to see which of these commits caused the issue!
https://github.com/torvalds/linux/commits/master/drivers/net/ethernet/realtek/r8169.c
Maybe applying this patch will help - https://lore.kernel.org/patchwork/patch/883134/
I'll give it a try and report back when I can!
---
NSA310s, NSA310, C.H.I.P, Banana Pi, Orange Pi PC & Zero, RPI 1,2Bx8
Edited 1 time(s). Last edit at 03/10/2019 08:50PM by mpmc.
https://github.com/torvalds/linux/commits/master/drivers/net/ethernet/realtek/r8169.c
Maybe applying this patch will help - https://lore.kernel.org/patchwork/patch/883134/
I'll give it a try and report back when I can!
---
NSA310s, NSA310, C.H.I.P, Banana Pi, Orange Pi PC & Zero, RPI 1,2Bx8
Edited 1 time(s). Last edit at 03/10/2019 08:50PM by mpmc.
|
Re: Zyxel 310. No ethernet since the 4.20 kernel on Arch - is it working in Debian? March 25, 2019 04:53PM |
Registered: 6 years ago Posts: 45 |
|
Re: Zyxel 310. No ethernet since the 4.20 kernel on Arch - is it working in Debian? March 25, 2019 05:25PM |
Admin Registered: 13 years ago Posts: 18,900 |
|
Re: Zyxel 310. No ethernet since the 4.20 kernel on Arch - is it working in Debian? March 25, 2019 08:07PM |
Registered: 7 years ago Posts: 21 |
|
Re: Zyxel 310. No ethernet since the 4.20 kernel on Arch - is it working in Debian? March 25, 2019 11:17PM |
Admin Registered: 13 years ago Posts: 18,900 |
This bug was a hard one. Only people who have seen the PCI issue recently on the mailing list could relate to that quickly like Heiner Kallweit did!
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
