Kernel 5.1.0 on ix-dl no sensors, Need recompile ?

I Used Kernel 5.1.0 on my ix-dl, Here no sensors:

Kernel 4.20.6:

<root@IX2-DL>~/:uname -a
Linux IX2-DL 4.20.6-kirkwood-tld-1 #1 PREEMPT Thu Jan 31 21:41:45 PST 2019 armv5tel GNU/Linux
<root@IX2-DL>~/:sensors
adt7473-i2c-0-2e
Adapter: mv64xxx_i2c adapter
in1:          +1.10 V  (min =  +0.00 V, max =  +2.99 V)
+3.3V:        +3.35 V  (min =  +2.96 V, max =  +3.61 V)
fan1:         834 RPM  (min =    0 RPM)
fan2:           0 RPM  (min =    0 RPM)
fan3:           0 RPM  (min =    0 RPM)
fan4:           0 RPM  (min =    0 RPM)
temp1:        +53.2°C  (low  = -63.0°C, high = +191.0°C)
                       (crit = +100.0°C, hyst = +96.0°C)
Board Temp:   +50.2°C  (low  = -63.0°C, high = +191.0°C)
                       (crit = +100.0°C, hyst = +96.0°C)
temp3:        +47.5°C  (low  = -63.0°C, high = +191.0°C)
                       (crit = +100.0°C, hyst = +96.0°C)

Kernel 5.1.0:

<root@IX2-DL>~/:uname -a
Linux IX2-DL 5.1.0-kirkwood-tld-1 #1 PREEMPT Tue May 7 00:16:02 PDT 2019 armv5tel GNU/Linux
<root@IX2-DL>~/:sensors
No sensors found!
Make sure you loaded all the kernel drivers you need.
Try sensors-detect to find out which these are.

Error log in kernel 5.1.0 start:

[   16.887766] orion_wdt: Initial timeout 21 sec
[   16.929788] adt7475 0-002e: hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[   17.039903] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   17.057012] adt7475 0-002e: ADT7473 device, revision 0
[   17.100609] marvell-cesa f1030000.crypto: CESA device successfully registered
[   17.121755] sd 1:0:0:0: Attached scsi generic sg1 type 0

olderzeus,

Which DTB are you using to boot this box?

And have you tried to modprobe it manually?

modprobe adt7475

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)



Edited 1 time(s). Last edit at 06/02/2019 09:14PM by bodhi.

https://forum.doozan.com/read.php?3,19216

I used the DTB from this thread.

Sorry for my own carelessness.

I had test & more times to run dpkg -i linux-image-5.1.0-kirkwood-tld-1_1.0_armel.deb
but not check the module files.

I checked & not found /lib/modules/5.1.0-kirkwood-tld-1, So I'm retried dpkg -i linux-image-5.1.0-kirkwood-tld-1_1.0_armel.deb and checked module files.

It's correct now.

<root@IX2-DL>~/:uname -a
Linux IX2-DL 5.1.0-kirkwood-tld-1 #1 PREEMPT Tue May 7 00:16:02 PDT 2019 armv5tel GNU/Linux
<root@IX2-DL>~/:sensors
adt7473-i2c-0-2e
Adapter: mv64xxx_i2c adapter
in1:          +1.10 V  (min =  +0.00 V, max =  +2.99 V)
+3.3V:        +3.35 V  (min =  +2.96 V, max =  +3.61 V)
fan1:         812 RPM  (min =    0 RPM)
fan2:           0 RPM  (min =    0 RPM)
fan3:           0 RPM  (min =    0 RPM)
fan4:           0 RPM  (min =    0 RPM)
temp1:        +54.5°C  (low  = -63.0°C, high = +191.0°C)
                       (crit = +100.0°C, hyst = +96.0°C)
Board Temp:   +52.2°C  (low  = -63.0°C, high = +191.0°C)
                       (crit = +100.0°C, hyst = +96.0°C)
temp3:        +49.2°C  (low  = -63.0°C, high = +191.0°C)
                       (crit = +100.0°C, hyst = +96.0°C)

olderzeus,

Glad that you've figured out the problem!

-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)