Re: WDmycloudex4100 instructions June 18, 2019 09:26PM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: WDmycloudex4100 instructions June 18, 2019 10:17PM |
Admin Registered: 13 years ago Posts: 18,495 |
Quote
port 2 works out of the box as eth0
Re: WDmycloudex4100 instructions June 19, 2019 05:44PM |
Registered: 4 years ago Posts: 28 |
pi@raspberrypi:~ $ kwboot -t -B 115200 /dev/ttyUSB0 -b u-boot-a38x-Yellowstone_2014T30p6_bodhi-tld-6-nand-uart.bin -s 0 -q 1 Sending boot message. Please reboot the target...\ Sending boot image... 0 % [......................................................................] 0 % [......................................................................] 1 % [......................................................................] <snip> 98 % [......................................................................] 99 % [..................................................] [Type Ctrl-\ + c to quit] __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01_v1.06 (Jun 30 2017 - 16:08:19) Marvell version: 2014_T3.0p6 - bodhi-tld-6 mvBoardSatRRead: Error: Read from S@R failed mvBoardSatRRead: Error: Read from S@R failed mvBoardSatRRead: Error: Read from S@R failed Board: DB-88F6820-BP SoC: MV88F6828 Rev A0 running 2 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1600 [MHz] L2 @ 800 [MHz] TClock @ 200 [MHz] DDR @ 800 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 2 GiB Map: Code: 0x7fece000:0x7ff960f0 BSS: 0x7ffef654 Stack: 0x7f9cdf20 Heap: 0x7f9ce000:0x7fece000 U-Boot Environment: 0x00100000:0x00180000 Address: 0x00100000(NAND) NAND: ID: dcad ,512 MiB MMC: mv_sdh: 0 bootcmd: run bootcmd_custom; setenv bootargs root=/dev/ram console=ttyS0,115200; nand read.e 0xa00000 0x500000 0x500000;nand read.e 0xf00000 0xa00000 0x500000;bootm 0xa00000 0xf00000 USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Creating 1 MTD partitions on "nand0": 0x00001f500000-0x00001ff00000 : "mtd=7" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=7" UBI: MTD device size: 10 MiB UBI: number of good PEBs: 80 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 32 UBI: total number of reserved PEBs: 48 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 3/1 UBIFS: mounted UBI device 0, volume 0, name "reserve2" UBIFS: mounted read-only UBIFS: file system size: 4063232 bytes (3968 KiB, 3 MiB, 32 LEBs) UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: LZO UBIFS: reserved for root: 200807 bytes (196 KiB) Loading file '/mac_addr' to addr 0x02000000 with size 36 (0x00000024)... Done lan mac_addr : 00 90 a9 e4 89 34 Set lan 0 WakeOnLan ok Set lan 1 WakeOnLan ok MicroP Enable HD Enable HD1 Enable HD2 Enable HD3 Enable HD4 Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | 0x00 | | egiga1 | SGMII | 0x01 | egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 Marvell>> setenv set_bootargs_stock 'setenv bootargs root=/dev/ram console=ttyS0,115200' Marvell>> setenv bootcmd_stock 'echo Booting from stock ... ; run set_bootargs_stock; printenv bootargs; nand read.e 0xa00000 0x500000 0x500000;nand read.e 0xf00000 0xa00000 0x500000;bootm 0xa00000 0xf00000' Marvell>> setenv bootdev 'usb' Marvell>> setenv device '0:1' Marvell>> setenv load_image_addr '0x02000000' Marvell>> setenv load_initrd_addr '0x2900000' Marvell>> setenv load_image 'echo loading Image ...; ext2load $bootdev $device $load_image_addr /boot/uImage' Marvell>> setenv load_initrd 'echo loading uInitrd ...; ext2load $bootdev $device $load_initrd_addr /boot/uInitrd' Marvell>> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial mtdparts=armada-nand:5m@0(u-boot),5m@5m(kernel),5m@10m(uRamdisk),441m@15m(image.cfs),15m@456m(rescue_fw),20m@471m(config),10m@491m(reserve1),10m@501m(reserve2)' Marvell>> setenv bootcmd_usb 'echo Booting from USB ...; usb start; setenv fdt_skip_update yes; usb start; run usb_set_bootargs; if run load_image; then if run load_initrd; then bootm $load_image_addr $load_initrd_addr; else bootm $load_image_addr; fi; fi' Marvell>> setenv bootcmd_custom 'if run bootcmd_usb; then ; fi; run bootcmd_stock; reset' Marvell>> setenv bootcmd 'run bootcmd_custom' Marvell>> boot Booting from USB ... (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 4 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found (Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 3) : USB XHCI 1.00 scanning bus 0 for devices... 4 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found loading Image ... 4037164 bytes read in 396 ms (9.7 MiB/s) loading uInitrd ... 7070236 bytes read in 476 ms (14.2 MiB/s) ## Booting image at 02000000 ... ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-4.12.4-mvebu-tld-1 Created: 2019-06-18 21:41:04 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4037100 Bytes = 3.9 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02900000 ... Image Name: initramfs-4.12.4-mvebu-tld-1 Created: 2017-08-22 11:10:43 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 7070172 Bytes = 6.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.12.4-mvebu-tld-1 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #1 SMP PREEMPT Sat Jul 29 21:56:37 PDT 2017 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: WD My Cloud EX4100 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] percpu: Embedded 17 pages/cpu @eefc8000 s40460 r8192 d20980 u69632 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522752 [ 0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial mtdparts=armada-nand:5m@0(u-boot),5m@5m(kernel),5m@10m(uRamdisk),441m@15m(image.cfs),15m@456m(rescue_fw),20m@471m(config),10m@491m(reserve1),10m@501m(reserve2) [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 2059460K/2097152K available (8192K kernel code, 712K rwdata, 2080K rodata, 1024K init, 331K bss, 37692K reserved, 0K cma-reserved, 1310720K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB) [ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB) [ 0.000000] .data : 0xc0d00000 - 0xc0db2308 ( 713 kB) [ 0.000000] .bss : 0xc0db9a84 - 0xc0e0ca58 ( 332 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 D prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001 [ 0.000000] Switching to timer-based delay loop, resolution 40ns [ 0.000003] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns [ 0.007873] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns [ 0.019066] Console: colour dummy device 80x30 [ 0.023580] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000) [ 0.033971] pid_max: default: 32768 minimum: 301 [ 0.038719] Security Framework initialized [ 0.042913] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.049585] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.057033] CPU: Testing write buffer coherency: ok [ 0.062092] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.103878] Setting up static identity map for 0x100000 - 0x100060 [ 0.110178] mvebu-soc-id: MVEBU SoC ID=0x6828, Rev=0x4 [ 0.115466] mvebu-pmsu: Initializing Power Management Service Unit [ 0.173857] smp: Bringing up secondary CPUs ... [ 0.233907] Booting CPU 1 [ 0.236748] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.236795] smp: Brought up 1 node, 2 CPUs [ 0.246676] SMP: Total of 2 processors activated (100.00 BogoMIPS). [ 0.252996] CPU: All CPU(s) started in SVC mode. [ 0.258209] devtmpfs: initialized [ 0.263206] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.271115] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.281003] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.287274] prandom: seed boundary self test passed [ 0.293912] prandom: 100 self tests passed [ 0.298072] pinctrl core: initialized pinctrl subsystem [ 0.303948] NET: Registered protocol family 16 [ 0.308994] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.316874] cpuidle: using governor ladder [ 0.321046] cpuidle: using governor menu [ 0.325159] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.333208] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.339217] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling [ 0.347363] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling [ 0.370765] vgaarb: loaded [ 0.373767] SCSI subsystem initialized [ 0.384125] usbcore: registered new interface driver usbfs [ 0.389698] usbcore: registered new interface driver hub [ 0.395324] usbcore: registered new device driver usb [ 0.400673] media: Linux media interface: v0.10 [ 0.405324] Linux video capture interface: v2.00 [ 0.414031] clocksource: Switched to clocksource armada_370_xp_clocksource [ 0.455029] VFS: Disk quotas dquot_6.6.0 [ 0.459058] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.471847] NET: Registered protocol family 2 [ 0.476687] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.483820] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.490436] TCP: Hash tables configured (established 8192 bind 8192) [ 0.496903] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.502898] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.509459] NET: Registered protocol family 1 [ 0.524141] RPC: Registered named UNIX socket transport module. [ 0.530116] RPC: Registered udp transport module. [ 0.534896] RPC: Registered tcp transport module. [ 0.539660] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.546263] Unpacking initramfs... [ 0.780637] Freeing initrd memory: 6908K [ 0.784823] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.791581] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.800438] audit: initializing netlink subsys (disabled) [ 0.806012] audit: type=2000 audit(0.791:1): state=initialized audit_enabled=0 res=1 [ 0.806234] Initialise system trusted keyrings [ 0.806251] Key type blacklist registered [ 0.806313] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 0.813872] zbud: loaded [ 0.834453] NFS: Registering the id_resolver key type [ 0.839572] Key type id_resolver registered [ 0.843818] Key type id_legacy registered [ 0.847924] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.854716] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.861231] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.868615] orangefs_debugfs_init: called with debug mask: :none: :0: [ 0.875223] orangefs_init: module version upstream loaded [ 0.882823] Key type asymmetric registered [ 0.887012] Asymmetric key parser 'x509' registered [ 0.891973] bounce: pool size: 64 pages [ 0.895933] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.903378] io scheduler noop registered [ 0.907388] io scheduler deadline registered [ 0.911749] io scheduler cfq registered (default) [ 0.917423] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver [ 0.926019] mv_xor f1060800.xor: Marvell shared XOR driver [ 0.984433] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy sg intr ) [ 0.992300] mv_xor f1060900.xor: Marvell shared XOR driver [ 1.054409] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy sg intr ) [ 1.095462] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.103194] console [ttyS0] disabled [ 1.127136] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 23, base_baud = 12500000) is a 16550A [ 1.136279] console [ttyS0] enabled [ 1.136279] console [ttyS0] enabled [ 1.143367] bootconsole [earlycon0] disabled [ 1.143367] bootconsole [earlycon0] disabled [ 1.172784] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 24, base_baud = 12500000) is a 16550A [ 1.182491] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 1.191609] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 1.200905] scsi host0: ahci-mvebu [ 1.214554] scsi host1: ahci-mvebu [ 1.218090] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 44 [ 1.226064] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 44 [ 1.234149] ahci-mvebu f10e0000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode [ 1.243236] ahci-mvebu f10e0000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 1.252538] scsi host2: ahci-mvebu [ 1.256155] scsi host3: ahci-mvebu [ 1.259688] ata3: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x100 irq 45 [ 1.267662] ata4: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x180 irq 45 [ 1.276078] pxa3xx-nand f10d0000.flash: This platform can't do DMA on this device [ 1.283926] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xdc [ 1.290329] nand: Hynix H27U4G8F2DTR-BC [ 1.294190] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.301794] pxa3xx-nand f10d0000.flash: ECC strength 16, ECC step size 2048 [ 1.308993] Bad block table found at page 262080, version 0x01 [ 1.315181] Bad block table found at page 262016, version 0x01 [ 1.321203] nand_read_bbt: bad block at 0x000006960000 [ 1.326446] 8 ofpart partitions found on MTD device pxa3xx_nand-0 [ 1.332564] Creating 8 MTD partitions on "pxa3xx_nand-0": [ 1.337994] 0x000000000000-0x000000500000 : "U-Boot" [ 1.353643] 0x000000500000-0x000000f00000 : "uImage" [ 1.359264] 0x000000a00000-0x000001900000 : "uRamdisk" [ 1.375046] 0x000000f00000-0x00001d700000 : "image.cfs" [ 1.392392] 0x00001c800000-0x000039f00000 : "rescue_fw" [ 1.397657] mtd: partition "rescue_fw" extends beyond the end of device "pxa3xx_nand-0" -- size truncated to 0x3800000 [ 1.419132] 0x00001d700000-0x00003c200000 : "config" [ 1.424141] mtd: partition "config" extends beyond the end of device "pxa3xx_nand-0" -- size truncated to 0x2900000 [ 1.445309] 0x00001eb00000-0x00003e000000 : "reserve1" [ 1.450471] mtd: partition "reserve1" extends beyond the end of device "pxa3xx_nand-0" -- size truncated to 0x1500000 [ 1.471775] 0x00001f500000-0x00003f400000 : "reserve2" [ 1.476959] mtd: partition "reserve2" extends beyond the end of device "pxa3xx_nand-0" -- size truncated to 0xb00000 [ 1.498760] m25p80 spi0.0: unrecognized JEDEC id bytes: ff, ff, ff [ 1.505505] libphy: Fixed MDIO Bus: probed [ 1.509953] libphy: orion_mdio_bus: probed [ 1.519637] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled [ 1.528629] mvneta f1070000.ethernet eth0: Using random mac address 2e:87:45:78:cf:38 [ 1.537961] mvneta f1030000.ethernet eth1: Using random mac address 5a:53:97:7b:ae:b2 [ 1.546042] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.552607] ehci-pci: EHCI PCI platform driver [ 1.557118] ehci-orion: EHCI orion driver [ 1.561255] orion-ehci f1058000.usb: EHCI Host Controller [ 1.565515] ata1: SATA link down (SStatus 0 SControl 300) [ 1.572132] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 [ 1.579793] orion-ehci f1058000.usb: irq 40, io mem 0xf1058000 [ 1.614038] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 [ 1.620094] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.626932] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.634193] usb usb1: Product: EHCI Host Controller [ 1.639091] usb usb1: Manufacturer: Linux 4.12.4-mvebu-tld-1 ehci_hcd [ 1.645574] usb usb1: SerialNumber: f1058000.usb [ 1.650515] hub 1-0:1.0: USB hub found [ 1.654317] hub 1-0:1.0: 1 port detected [ 1.658694] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.664052] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 [ 1.671632] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.680233] xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000 [ 1.686081] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.692900] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.700169] usb usb2: Product: xHCI Host Controller [ 1.705074] usb usb2: Manufacturer: Linux 4.12.4-mvebu-tld-1 xhci-hcd [ 1.711542] usb usb2: SerialNumber: f10f0000.usb3 [ 1.716573] hub 2-0:1.0: USB hub found [ 1.720354] hub 2-0:1.0: 1 port detected [ 1.724455] xhci-hcd f10f0000.usb3: xHCI Host Controller [ 1.729795] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 [ 1.734045] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 1.743596] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.751786] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.758620] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.766678] usb usb3: Product: xHCI Host Controller [ 1.771576] usb usb3: Manufacturer: Linux 4.12.4-mvebu-tld-1 xhci-hcd [ 1.774042] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 1.784041] ata4: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 1.790511] usb usb3: SerialNumber: f10f0000.usb3 [ 1.795521] hub 3-0:1.0: USB hub found [ 1.799301] hub 3-0:1.0: 1 port detected [ 1.803470] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.808835] ata4.00: ATA-8: WDC WD20EARX-00PASB0, 51.0AB51, max UDMA/133 [ 1.808839] ata4.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 1.822436] ata2.00: ATA-8: ST2000DM001-1CH164, CC26, max UDMA/133 [ 1.822440] ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 1.828672] ata4.00: configured for UDMA/133 [ 1.839851] ata2.00: configured for UDMA/133 [ 1.839853] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 [ 1.839919] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010 [ 1.839939] xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000 [ 1.840016] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.840020] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.840023] usb usb4: Product: xHCI Host Controller [ 1.840025] usb usb4: Manufacturer: Linux 4.12.4-mvebu-tld-1 xhci-hcd [ 1.840028] usb usb4: SerialNumber: f10f8000.usb3 [ 1.844324] hub 4-0:1.0: USB hub found [ 1.844340] hub 4-0:1.0: 1 port detected [ 1.844492] xhci-hcd f10f8000.usb3: xHCI Host Controller [ 1.844500] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 [ 1.844541] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.844598] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.844602] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.844604] usb usb5: Product: xHCI Host Controller [ 1.844607] usb usb5: Manufacturer: Linux 4.12.4-mvebu-tld-1 xhci-hcd [ 1.844609] usb usb5: SerialNumber: f10f8000.usb3 [ 1.851853] hub 5-0:1.0: USB hub found [ 1.851871] hub 5-0:1.0: 1 port detected [ 1.852074] usbcore: registered new interface driver usblp [ 1.852139] usbcore: registered new interface driver usb-storage [ 1.860523] mousedev: PS/2 mouse device common for all mice [ 1.866332] armada38x-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 [ 1.866482] i2c /dev entries driver [ 1.891064] (NULL device *): hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info(). [ 1.892211] orion_wdt: Initial timeout 171 sec [ 1.893497] marvell-cesa f1090000.crypto: CESA device successfully registered [ 1.893594] hidraw: raw HID events driver (C) Jiri Kosina [ 1.897046] usbcore: registered new interface driver usbhid [ 1.897047] usbhid: USB HID core driver [ 1.897181] drop_monitor: Initializing network drop monitor service [ 1.897217] Netfilter messages via NETLINK v0.30. [ 1.897226] ip_set: protocol 6 [ 1.897398] NET: Registered protocol family 10 [ 1.908007] Segment Routing with IPv6 [ 1.908040] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.908676] NET: Registered protocol family 17 [ 1.908704] 8021q: 802.1Q VLAN Support v1.8 [ 1.908734] Key type dns_resolver registered [ 1.908823] ThumbEE CPU extension supported. [ 1.908828] Registering SWP/SWPB emulation handler [ 1.926184] registered taskstats version 1 [ 1.926186] Loading compiled-in X.509 certificates [ 1.926219] zswap: loaded using pool lzo/zbud [ 2.009296] Key type big_key registered [ 2.031448] Key type encrypted registered [ 2.045523] armada38x-rtc f10a3800.rtc: setting system clock to 2019-06-19 20:33:35 UTC (1560976415) [ 2.094052] usb 2-1: new high-speed USB device number 2 using xhci-hcd [ 2.129008] scsi 1:0:0:0: Direct-Access ATA ST2000DM001-1CH1 CC26 PQ: 0 ANSI: 5 [ 2.137695] sd 1:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB) [ 2.145712] sd 1:0:0:0: [sda] 4096-byte physical blocks [ 2.150990] sd 1:0:0:0: [sda] Write Protect is off [ 2.155858] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.208724] ata3.00: ATA-8: WDC WD20EARX-008FB0, 51.0AB51, max UDMA/133 [ 2.215387] ata3.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 2.223899] ata3.00: configured for UDMA/133 [ 2.228487] scsi 2:0:0:0: Direct-Access ATA WDC WD20EARX-008 AB51 PQ: 0 ANSI: 5 [ 2.237136] sd 2:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB) [ 2.244954] sd 2:0:0:0: [sdb] 4096-byte physical blocks [ 2.250415] scsi 3:0:0:0: Direct-Access ATA WDC WD20EARX-00P AB51 PQ: 0 ANSI: 5 [ 2.254077] sd 2:0:0:0: [sdb] Write Protect is off [ 2.254238] usb 2-1: New USB device found, idVendor=045b, idProduct=0209 [ 2.254242] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.254356] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.264331] hub 2-1:1.0: USB hub found [ 2.264402] hub 2-1:1.0: 4 ports detected [ 2.294648] sd 3:0:0:0: [sdc] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB) [ 2.302480] sd 3:0:0:0: [sdc] 4096-byte physical blocks [ 2.307810] sd 3:0:0:0: [sdc] Write Protect is off [ 2.312737] sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.322031] sdb: sdb1 sdb2 sdb3 sdb4 [ 2.326742] sd 2:0:0:0: [sdb] Attached SCSI removable disk [ 2.338380] sdc: sdc1 [ 2.341262] sd 3:0:0:0: [sdc] Attached SCSI removable disk [ 2.394245] usb 3-1: new SuperSpeed USB device number 2 using xhci-hcd [ 2.425592] usb 3-1: New USB device found, idVendor=045b, idProduct=0210 [ 2.432323] usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.439983] hub 3-1:1.0: USB hub found [ 2.444015] hub 3-1:1.0: 4 ports detected [ 2.584043] usb 2-1.2: new high-speed USB device number 3 using xhci-hcd [ 2.724412] usb 2-1.2: New USB device found, idVendor=ffff, idProduct=5678 [ 2.731318] usb 2-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.738668] usb 2-1.2: Product: Disk 2.0 [ 2.742606] usb 2-1.2: Manufacturer: USB [ 2.746552] usb 2-1.2: SerialNumber: 9207266731057219943 [ 2.752202] usb-storage 2-1.2:1.0: USB Mass Storage device detected [ 2.758638] scsi host4: usb-storage 2-1.2:1.0 [ 3.766367] scsi 4:0:0:0: Direct-Access VendorCo ProductCode 2.00 PQ: 0 ANSI: 4 [ 3.785243] sd 4:0:0:0: [sdd] 30720000 512-byte logical blocks: (15.7 GB/14.6 GiB) [ 3.792971] sd 4:0:0:0: [sdd] Write Protect is off [ 3.797937] sd 4:0:0:0: [sdd] No Caching mode page found [ 3.803273] sd 4:0:0:0: [sdd] Assuming drive cache: write through [ 3.811508] sdd: sdd1 [ 3.814789] sd 4:0:0:0: [sdd] Attached SCSI removable disk [ 6.528883] sda: sda1 [ 6.531756] sd 1:0:0:0: [sda] Attached SCSI removable disk [ 6.537915] Freeing unused kernel memory: 1024K Loading, please wait... starting version 232 [ 6.583840] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 6.587457] random: udevadm: uninitialized urandom read (16 bytes read) [ 6.588083] random: udevadm: uninitialized urandom read (16 bytes read) [ 6.588117] random: udevadm: uninitialized urandom read (16 bytes read) [ 6.588470] random: udevadm: uninitialized urandom read (16 bytes read) [ 6.588674] random: udevadm: uninitialized urandom read (16 bytes read) [ 6.588879] random: udevadm: uninitialized urandom read (16 bytes read) [ 6.589092] random: udevadm: uninitialized urandom read (16 bytes read) [ 6.589315] random: udevadm: uninitialized urandom read (16 bytes read) [ 6.589503] random: udevadm: uninitialized urandom read (16 bytes read) [ 6.841579] usbcore: registered new interface driver uas [ 6.941336] random: fast init done Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Warning: fsck not present, so sk[ 56.375415] EXT4-fs (sdd1): mounting ext3 file system using the ext4 subsystem ipping root file system [ 56.384636] EXT4-fs (sdd1): INFO: recovery required on readonly filesystem [ 56.392134] EXT4-fs (sdd1): write access will be enabled during recovery [ 57.308419] EXT4-fs (sdd1): recovery complete [ 57.318636] EXT4-fs (sdd1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [ ok ] Setting hostname to 'debian'...done. [ 58.088602] random: crng init done [....] Starting the hotplug events dispatcher: systemd-udevdstarting version 232 . ok [ ok ] Synthesizing the initial hotplug events...done. [....] Waiting for /dev to be fully populated...[ 58.779108] sd 1:0:0:0: Attached scsi generic sg0 type 0 [ 58.788713] sd 2:0:0:0: Attached scsi generic sg1 type 0 [ 58.803310] sd 3:0:0:0: Attached scsi generic sg2 type 0 [ 58.809524] sd 4:0:0:0: Attached scsi generic sg3 type 0 done. [ ok ] Activating swap:. [ 65.100265] EXT4-fs (sdd1): re-mounted. Opts: (null) [....] Will now check root file system:fsck from util-linux 2.29.2 [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sdd1 e2fsck 1.43.4 (31-Jan-2017) rootfs: clean, 22033/960992 files, 307946/3839992 blocks . ok [ 65.236411] EXT4-fs (sdd1): re-mounted. Opts: errors=remount-ro [ ok ] Will now activate lvm and md swap:done. [info] Will now check all file systems. fsck from util-linux 2.29.2 Checking all file systems. LABEL=rootfs is mounted [ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. [ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done. [ ok . [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables...done. [ ok ] Initializing random number generator...done. [ 66.494550] m88e1318_get_wol: phy_id = 0x1410dd1 OK [ 66.499563] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.5 Copyright 2004-2016 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/2e:87:45:78:cf:38 Sending on LPF/eth0/2e:87:45:78:cf:38 Sending on Socket/fallback DHCPREQUEST of 10.0.0.234 on eth0 to 255.255.255.255 port 67 [ 70.644480] mvneta f1070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 70.652359] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready DHCPREQUEST of 10.0.0.234 on eth0 to 255.255.255.255 port 67 DHCPNAK from 10.0.0.1 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 DHCPREQUEST of 10.0.0.135 on eth0 to 255.255.255.255 port 67 DHCPOFFER of 10.0.0.135 from 10.0.0.1 DHCPACK of 10.0.0.135 from 10.0.0.1 bound to 10.0.0.135 -- renewal in 250286 seconds. done. [ ok ] Starting RPC port mapper daemon: rpcbind. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 2686 (syslogd) . ok [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting periodic command scheduler: cron. [ ok ] Starting system message bus: dbus. [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 2685 (klogd) . ok [ ok ] Starting NTP server: ntpd. [ ok ] Running local boot scripts (/etc/rc.local). Debian GNU/Linux 9 debian ttyS0 debian login: root Password: Last login: Tue Jun 18 16:59:09 PDT 2019 on ttyS0 Linux debian 4.12.4-mvebu-tld-1 #1 SMP PREEMPT Sat Jul 29 21:56:37 PDT 2017 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. debian 10.0.0.135 n WD My Cloud EX4100 Linux version 4.12.4-mvebu-tld-1 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #1 SMP PREEMPT Sat Jul 29 21:56:37 PDT 2017
Re: WDmycloudex4100 instructions June 19, 2019 05:45PM |
Registered: 4 years ago Posts: 28 |
Debian 9.1 root@debian:~# sudo apt update -bash: sudo: command not found root@debian:~# apt update <snip> [ 1211.947250] EXT4-fs error (device sdd1): __ext4_new_inode:1071: comm dpkg: failed to insert inode 114022: doubly allocated? [ 1212.432771] Aborting journal on device sdd1-8. [ 1212.440198] EXT4-fs (sdd1): Remounting filesystem read-only [ 1212.446147] EXT4-fs error (device sdd1) in ext4_symlink:3089: IO failure dpkg: error processing archive /var/cache/apt/archives/libc6_2.24-11+deb9u4_armhf.deb (--unpack): unable to make backup symlink for './lib/ld-linux-armhf.so.3': Input/output error dpkg: error while cleaning up: unable to remove newly-extracted version of '/lib/ld-linux-armhf.so.3': Read-only file system dpkg: error while cleaning up: unable to restore backup version of '/lib/arm-linux-gnueabihf/libutil.so.1': Read-only file system dpkg: error while cleaning up: unable to restore backup version of '/lib/arm-linux-gnueabihf/libthread_db.so.1': Read-only file system <snip> unable to restore backup version of '/usr/lib/arm-linux-gnueabihf/gconv/IBM1146.so': Read-only file system dpkg: error while cleaning up: unable to restore backup version of '/usr/lib/arm-linux-gnueabihf/gconv/IBM1145.so': Read-only file system dpkg: error while cleaning up: unable to restore backup version of '/usr/lib/arm-linux-gnueabihf/gconv/IBM1144.so': Read-only file system dpkg: error while cleaning up: unable to restore backup version of '/usr/lib/arm-linux-gnuE: Sub-process /usr/bin/dpkg returned an error code (2) W: Problem unlinking the file /var/cache/apt/pkgcache.bin - pkgDPkgPM::Go (30: Read-only file system) root@debian:~# sudo -bash: sudo: command not found root@debian:~# aot-get install systemd -bash: aot-get: command not found root@debian:~# apt-get install systemd W: Not using locking for read only lock file /var/lib/dpkg/lock E: dpkg was interrupted, you must manually run 'dpkg --configure -a' to correct the problem. root@debian:~# apt-get install systemd W: Not using locking for read only lock file /var/lib/dpkg/lock E: dpkg was interrupted, you must manually run 'dpkg --configure -a' to correct the problem. root@debian:~# apt-get install systemd W: Not using locking for read only lock file /var/lib/dpkg/lock E: dpkg was interrupted, you must manually run 'dpkg --configure -a' to correct the problem. are-properties-commonstall apt-transport-https ca-certificates curl gnupg2 softw W: Not using locking for read only lock file /var/lib/dpkg/lock E: dpkg was interrupted, you must manually run 'dpkg --configure -a' to correct the problem. are-properties-commonstall apt-transport-https ca-certificates curl gnupg2 softw W: Not using locking for read only lock file /var/lib/dpkg/lock E: dpkg was interrupted, you must manually run 'dpkg --configure -a' to correct the problem. root@debian:~# dpkg --configure -a dpkg: error: unable to access dpkg status area: Read-only file system root@debian:~# dpkg --configure -a dpkg: error: unable to access dpkg status area: Read-only file system root@debian:~# mount -o remount /dev/sda1 mount: mount point /dev/sda1 does not exist root@debian:~# mount -o remount /dev/sda mount: mount point /dev/sda does not exist root@debian:~# ls /dev/ . ptyb8 ptyqd ptyw2 tty12 ttyb5 ttyqa ttyvf .. ptyb9 ptyqe ptyw3 tty13 ttyb6 ttyqb ttyw0 MAKEDEV ptyba ptyqf ptyw4 tty14 ttyb7 ttyqc ttyw1 autofs ptybb ptyr0 ptyw5 tty15 ttyb8 ttyqd ttyw2 block ptybc ptyr1 ptyw6 tty16 ttyb9 ttyqe ttyw3 bsg ptybd ptyr2 ptyw7 tty17 ttyba ttyqf ttyw4 btrfs-control ptybe ptyr3 ptyw8 tty18 ttybb ttyr0 ttyw5 bus ptybf ptyr4 ptyw9 tty19 ttybc ttyr1 ttyw6 char ptyc0 ptyr5 ptywa tty2 ttybd ttyr2 ttyw7 console ptyc1 ptyr6 ptywb tty20 ttybe ttyr3 ttyw8 cpu_dma_latency ptyc2 ptyr7 ptywc tty21 ttybf ttyr4 ttyw9 cuse ptyc3 ptyr8 ptywd tty22 ttyc0 ttyr5 ttywa disk ptyc4 ptyr9 ptywe tty23 ttyc1 ttyr6 ttywb fd ptyc5 ptyra ptywf tty24 ttyc2 ttyr7 ttywc full ptyc6 ptyrb ptyx0 tty25 ttyc3 ttyr8 ttywd fuse ptyc7 ptyrc ptyx1 tty26 ttyc4 ttyr9 ttywe gpiochip0 ptyc8 ptyrd ptyx2 tty27 ttyc5 ttyra ttywf gpiochip1 ptyc9 ptyre ptyx3 tty28 ttyc6 ttyrb ttyx0 i2c-0 ptyca ptyrf ptyx4 tty29 ttyc7 ttyrc ttyx1 i2c-1 ptycb ptys0 ptyx5 tty3 ttyc8 ttyrd ttyx2 input ptycc ptys1 ptyx6 tty30 ttyc9 ttyre ttyx3 kmem ptycd ptys2 ptyx7 tty31 ttyca ttyrf ttyx4 kmsg ptyce ptys3 ptyx8 tty32 ttycb ttys0 ttyx5 log ptycf ptys4 ptyx9 tty33 ttycc ttys1 ttyx6 loop-control ptyd0 ptys5 ptyxa tty34 ttycd ttys2 ttyx7 mapper ptyd1 ptys6 ptyxb tty35 ttyce ttys3 ttyx8 mem ptyd2 ptys7 ptyxc tty36 ttycf ttys4 ttyx9 memory_bandwidth ptyd3 ptys8 ptyxd tty37 ttyd0 ttys5 ttyxa mtd0 ptyd4 ptys9 ptyxe tty38 ttyd1 ttys6 ttyxb mtd0ro ptyd5 ptysa ptyxf tty39 ttyd2 ttys7 ttyxc mtd1 ptyd6 ptysb ptyy0 tty4 ttyd3 ttys8 ttyxd mtd1ro ptyd7 ptysc ptyy1 tty40 ttyd4 ttys9 ttyxe mtd2 ptyd8 ptysd ptyy2 tty41 ttyd5 ttysa ttyxf mtd2ro ptyd9 ptyse ptyy3 tty42 ttyd6 ttysb ttyy0 mtd3 ptyda ptysf ptyy4 tty43 ttyd7 ttysc ttyy1 mtd3ro ptydb ptyt0 ptyy5 tty44 ttyd8 ttysd ttyy2 mtd4 ptydc ptyt1 ptyy6 tty45 ttyd9 ttyse ttyy3 mtd4ro ptydd ptyt2 ptyy7 tty46 ttyda ttysf ttyy4 mtd5 ptyde ptyt3 ptyy8 tty47 ttydb ttyt0 ttyy5 mtd5ro ptydf ptyt4 ptyy9 tty48 ttydc ttyt1 ttyy6 mtd6 ptye0 ptyt5 ptyya tty49 ttydd ttyt2 ttyy7 mtd6ro ptye1 ptyt6 ptyyb tty5 ttyde ttyt3 ttyy8 mtd7 ptye2 ptyt7 ptyyc tty50 ttydf ttyt4 ttyy9 mtd7ro ptye3 ptyt8 ptyyd tty51 ttye0 ttyt5 ttyya mtdblock0 ptye4 ptyt9 ptyye tty52 ttye1 ttyt6 ttyyb mtdblock1 ptye5 ptyta ptyyf tty53 ttye2 ttyt7 ttyyc mtdblock2 ptye6 ptytb ptyz0 tty54 ttye3 ttyt8 ttyyd mtdblock3 ptye7 ptytc ptyz1 tty55 ttye4 ttyt9 ttyye mtdblock4 ptye8 ptytd ptyz2 tty56 ttye5 ttyta ttyyf mtdblock5 ptye9 ptyte ptyz3 tty57 ttye6 ttytb ttyz0 mtdblock6 ptyea ptytf ptyz4 tty58 ttye7 ttytc ttyz1 mtdblock7 ptyeb ptyu0 ptyz5 tty59 ttye8 ttytd ttyz2 net ptyec ptyu1 ptyz6 tty6 ttye9 ttyte ttyz3 network_latency ptyed ptyu2 ptyz7 tty60 ttyea ttytf ttyz4 network_throughput ptyee ptyu3 ptyz8 tty61 ttyeb ttyu0 ttyz5 null ptyef ptyu4 ptyz9 tty62 ttyec ttyu1 ttyz6 port ptyp0 ptyu5 ptyza tty63 ttyed ttyu2 ttyz7 ppp ptyp1 ptyu6 ptyzb tty7 ttyee ttyu3 ttyz8 psaux ptyp2 ptyu7 ptyzc tty8 ttyef ttyu4 ttyz9 ptmx ptyp3 ptyu8 ptyzd tty9 ttyp0 ttyu5 ttyza pts ptyp4 ptyu9 ptyze ttyS0 ttyp1 ttyu6 ttyzb ptya0 ptyp5 ptyua ptyzf ttyS1 ttyp2 ttyu7 ttyzc ptya1 ptyp6 ptyub random ttyS2 ttyp3 ttyu8 ttyzd ptya2 ptyp7 ptyuc rtc ttyS3 ttyp4 ttyu9 ttyze ptya3 ptyp8 ptyud rtc0 ttya0 ttyp5 ttyua ttyzf ptya4 ptyp9 ptyue sdb ttya1 ttyp6 ttyub ubi_ctrl ptya5 ptypa ptyuf sdb1 ttya2 ttyp7 ttyuc uhid ptya6 ptypb ptyv0 sdb2 ttya3 ttyp8 ttyud uinput ptya7 ptypc ptyv1 sdb3 ttya4 ttyp9 ttyue urandom ptya8 ptypd ptyv2 sdb4 ttya5 ttypa ttyuf vcs ptya9 ptype ptyv3 sdd ttya6 ttypb ttyv0 vcs1 ptyaa ptypf ptyv4 sdd1 ttya7 ttypc ttyv1 vcsa ptyab ptyq0 ptyv5 sg1 ttya8 ttypd ttyv2 vcsa1 ptyac ptyq1 ptyv6 sg3 ttya9 ttype ttyv3 vga_arbiter ptyad ptyq2 ptyv7 shm ttyaa ttypf ttyv4 vhci ptyae ptyq3 ptyv8 snapshot ttyab ttyq0 ttyv5 watchdog ptyaf ptyq4 ptyv9 snd ttyac ttyq1 ttyv6 watchdog0 ptyb0 ptyq5 ptyva stderr ttyad ttyq2 ttyv7 zero ptyb1 ptyq6 ptyvb stdin ttyae ttyq3 ttyv8 ptyb2 ptyq7 ptyvc stdout ttyaf ttyq4 ttyv9 ptyb3 ptyq8 ptyvd tty ttyb0 ttyq5 ttyva ptyb4 ptyq9 ptyve tty0 ttyb1 ttyq6 ttyvb ptyb5 ptyqa ptyvf tty1 ttyb2 ttyq7 ttyvc ptyb6 ptyqb ptyw0 tty10 ttyb3 ttyq8 ttyvd ptyb7 ptyqc ptyw1 tty11 ttyb4 ttyq9 ttyve root@debian:~# ls /dev/disk/ . .. by-id by-label by-partlabel by-partuuid by-path by-uuid root@debian:~# ls /dev/disk/by-label/ . .. rootfs root@debian:~# ls -lah /dev/disk/by-label/ total 0 drwxr-xr-x 2 root root 60 Jun 19 13:40 . drwxr-xr-x 8 root root 160 Jun 19 13:33 .. lrwxrwxrwx 1 root root 10 Jun 19 13:34 rootfs -> ../../sdd1 root@debian:~# sudo mount / -o remount,rw -bash: sudo: command not found root@debian:~# /usr/bin/sudo -bash: /usr/bin/sudo: No such file or directory root@debian:~# /usr/bin/ -bash: /usr/bin/: Is a directory root@debian:~# ls /usr/bin . neqn .. newgrp 2to3 nice 2to3-2.7 nl [ nohup addpart nproc apropos nroff apt nsenter apt-cache nstat apt-cdrom ntpdc apt-config ntpq apt-extracttemplates ntpsweep apt-ftparchive ntptrace apt-get numfmt apt-key od apt-mark openssl apt-sortpkgs pager arch partx awk passwd b2sum paste base32 pathchk base64 pdb basename pdb2.7 bashbug perf bootctl perl bsd-from perl5.24-arm-linux-gnueabihf bsd-write perl5.24.1 busctl perlbug c2ph perldoc c_rehash perlivp cal perlthanks calc_tickadj pg calendar pgrep captoinfo pic catchsegv pico catman piconv chacl pinentry chage pinentry-curses chattr pinky chcon pkill chfn pl2pm chrt pldd chsh pmap cksum pmount clear pod2html clear_console pod2man cmp pod2text col pod2usage colcrt podchecker colrm podselect column pr comm preconv compose prename corelist print cpan printenv cpan5.24-arm-linux-gnueabihf printerbanner crontab printf csplit prlimit ctstat prove cut pstruct dbus-cleanup-sockets ptar dbus-daemon ptardiff dbus-monitor ptargrep dbus-run-session ptx dbus-send pumount dbus-update-activation-environment pwdx dbus-uuidgen pyclean ddcmon pycompile deb-systemd-helper pydoc deb-systemd-invoke pydoc2.7 debconf pygettext debconf-apt-progress pygettext2.7 debconf-communicate python debconf-copydb python2 debconf-escape python2.7 debconf-set-selections pyversions debconf-show qemu-arm-static decode-dimms rcp decode-edid realpath decode-vaio rename delpart rename.ul dh_python2 renice dialog reset diff resizepart diff3 rev dircolors rgrep dirname rlogin dpkg routef dpkg-deb routel dpkg-divert rsh dpkg-maintscript-helper rsync dpkg-query rtstat dpkg-split run-mailcap dpkg-statoverride runcon dpkg-trigger rview du savelog dumpimage scp edit script editor scriptreplay enc2xs sdiff encguess see env select-editor eqn sensible-browser ex sensible-editor expand sensible-pager expiry seq expr setarch factor setfacl faillog setsid fallocate setterm find sftp flock sg fmt sha1sum fold sha224sum free sha256sum from sha384sum fw_printenv sha512sum fw_setenv shasum geqn shred getconf shuf getent skill getfacl slabtop getopt slogin gpasswd snice gpg soelim gpg-agent sort gpg-connect-agent splain gpg-zip split gpgconf ssh gpgparsemail ssh-add gpgsplit ssh-agent gpgv ssh-argv0 gpic ssh-copy-id groff ssh-keygen grog ssh-keyscan grops stat grotty stdbuf groups sum gtbl symcryptrun h2ph systemd-analyze h2xs systemd-cat hd systemd-cgls head systemd-cgtop helpztags systemd-delta hexdump systemd-detect-virt host systemd-mount hostid systemd-path hostnamectl systemd-resolve htop systemd-run iconv systemd-socket-activate id systemd-stdio-bridge infocmp tabs infotocap tac install tail instmodsh tasksel ionice taskset ipcmk tbl ipcrm tee ipcs test iperf tic iptables-xml timedatectl ischroot timeout join tload json_pp toe kbxutil top kernel-install touch kwboot tput last tr lastb traceproto lastlog traceproto.db lcf traceroute ldd traceroute-nanog less traceroute.db lessecho traceroute6 lessfile traceroute6.db lesskey troff lesspipe truncate lexgrog tset lft tsort lft.db tty libnetcfg tzselect line ucf link ucfq linux-check-removal ucfr linux-update-symlinks ul linux-version unexpand linux32 uniq linux64 unlink lnstat unlzma locale unmkinitramfs localectl unshare localedef unxz logger update-alternatives logname update-leap look uptime lorder users lsattr utmpdump lscpu vi lsinitramfs view lsipc vim.tiny lslocks vmstat lslogins w lsns w.procps lspgpot wall lzcat watch lzcmp watchgnupg lzdiff wc lzegrep wget lzfgrep whatis lzgrep whereis lzless which lzma whiptail lzmainfo who lzmore whoami man write mandb xargs manpath xsubpp mawk xxd mcookie xz md5sum xzcat md5sum.textutils xzcmp mesg xzdiff migrate-pubring-from-classic-gpg xzegrep mkenvimage xzfgrep mkfifo xzgrep mkimage xzless mksunxiboot xzmore namei yes nawk zdump ncal zipdetails root@debian:~# ls /usr/bin | grep sudol root@debian:~# ls /usr/bin | grep sudo root@debian:~# ls /usr/bin | grep su b2sum cksum md5sum md5sum.textutils mksunxiboot sha1sum sha224sum sha256sum sha384sum sha512sum shasum sum xsubpp root@debian:~# qZsu - -bash: qZsu: command not found root@debian:~# root@debian:~# su - debian 10.0.0.135 n WD My Cloud EX4100 Linux version 4.12.4-mvebu-tld-1 (root@tldDebianVM) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #1 SMP PREEMPT Sat Jul 29 21:56:37 PDT 2017 Debian 9.9 Wed Jun 19 15:33:11 PDT 2019 up 1 hour, 59 minutes root@debian:~# root@debian:~# apt-get install sudo -y W: Not using locking for read only lock file /var/lib/dpkg/lock E: dpkg was interrupted, you must manually run 'dpkg --configure -a' to correct the problem. root@debian:~# root@debian:~# dpkg --configure -a dpkg: error: unable to access dpkg status area: Read-only file system
Re: WDmycloudex4100 instructions June 20, 2019 12:54AM |
Admin Registered: 13 years ago Posts: 18,495 |
e2fsck /dev/sdb1
sync sync
mount
apt-get upgrade