TrashCanMan
Re: Help with iomega ix4-200d installation January 12, 2020 05:44AM |
>Quote
Debian Stretch and OpenMediaVault (OMV4) on
> Netgear Stora
>Quote
Thanks to information found mainly here
> (but also a little found elsewhere), I have made
> my Stora into an Open Media Vault. Note that the
> current release of OMV, OMV4, is NOT supported on
> Buster and does not install. You must install
> Stretch
>Quote
> Updated 24 Jul 2017:
>
> Basic Debian stretch Kirkwood rootfs for most
> Kirwood plugs:
>
> - tarball size: 188M
> - install size: 488M
> - The init system used in this rootfs is sysvinit
> . To boot with systemd, see note 2 below.
> - Installed packages: nano, avahi, ntp,
> busybox-syslogd (log to RAM), htop,
> isc-dhcp-client, dialog, bzip2, nfs server/client,
> iperf, ethtool, sysvinit-core, sysvinit, and
> sysvinit-utils.
> - see LED controls in /etc/rc.local, and
> /etc/init.d/halt
> - see some useful aliases in /root/.profile
> - root password: root
>
> Download at Dropbox:
>
> Debian-4.12.1-kirkwood-tld-1-rootfs-bodhi.tar.bz2
Re: Help with iomega ix4-200d installation January 12, 2020 06:43PM |
Registered: 4 years ago Posts: 1 |
Marvell>> printenv bootdelay=1 baudrate=115200 loads_echo=0 ipaddr=10.4.50.165 serverip=10.4.50.5 rootpath=/mnt/ARM_FS/ netmask=255.255.255.0 run_diag=yes CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage console=console=ttyS0,115200 mtdparts=nand_mtd:0xa0000@0x0(uboot),0x00010000@0x000a0000(param),32m@0x0(flash) uboot_start=0x0 uboot_size=0xa0000 env_start=0xa0000 env_size=0x10000 kernel_start=0xb0000 kernel_size=0x228000 initrd_size=0x300000 make_boot_args=setenv bootargs console=ttyS0,115200 mtdparts=nand_mtd:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash); flash_load=run make_boot_args;nand read.e 0x2000000 $(kernel_start) $(kernel_size);nand read.e 0x12000000 $(initrd_start) $(initrd_size);bootm 0x2000000 0x12000000; bootcmd=run flash_load; standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end); bootm 0x2000000; ethmtu=1500 mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host nandEcc=1bit netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no uboot_ver=v1.1.1 ethact=egiga0 mfgmodel=ix4 fw_ver=v1_0_11_3114995 preroot_ver=0.1.5 serial_number=5560Y01011G20100292J0J1 ethaddr=00:D0:B8:1F:50:89 serialNo=USC010GSA1 modelname=31962501 serialno=0,0118gBxqcDGGeguzOfdnxDWIlC5ZgYwIbHDMYf+jxSXdjJcBN5EYWlzzPx4UCzchQT,USC010GSA1, runintime=10800 ftpserver=192.168.16.4 testfile=4NC mfgtest_state=system_tested_ok stdin=serial stdout=serial stderr=serial mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no initrd_start=0x2d8000 disaMvPnp=no eth1addr=00:d0:b8:1f:50:8a enaAutoRecovery=yes pcieTune=no Environment size: 1931/16380 bytes Marvell>>
Marvell>> printenv bootdelay=1 baudrate=115200 loads_echo=0 ipaddr=10.4.50.165 serverip=10.4.50.5 rootpath=/mnt/ARM_FS/ netmask=255.255.255.0 run_diag=yes CASset=min MALLOC_len=1 ethprime=egiga0 bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:eth0:none image_name=uImage console=console=ttyS0,115200 mtdparts=nand_mtd:0xa0000@0x0(uboot),0x00010000@0x000a0000(param),32m@0x0(flash) uboot_start=0x0 uboot_size=0xa0000 env_start=0xa0000 env_size=0x10000 kernel_start=0xb0000 kernel_size=0x228000 initrd_size=0x300000 make_boot_args=setenv bootargs console=ttyS0,115200 mtdparts=nand_mtd:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash); flash_load=run make_boot_args;nand read.e 0x2000000 $(kernel_start) $(kernel_size);nand read.e 0x12000000 $(initrd_start) $(initrd_size);bootm 0x2000000 0x12000000; standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end); bootm 0x2000000; ethmtu=1500 mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host nandEcc=1bit netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no uboot_ver=v1.1.1 ethact=egiga0 mfgmodel=ix4 fw_ver=v1_0_11_3114995 preroot_ver=0.1.5 serial_number=5560Y01011G20100292J0J1 ethaddr=00:D0:B8:1F:50:89 serialNo=USC010GSA1 modelname=31962501 serialno=0,0118gBxqcDGGeguzOfdnxDWIlC5ZgYwIbHDMYf+jxSXdjJcBN5EYWlzzPx4UCzchQT,USC010GSA1, runintime=10800 ftpserver=192.168.16.4 testfile=4NC mfgtest_state=system_tested_ok load_initrd=ext2load usb 0:1 0x2100000 /boot/uInitrd load_uimage=ext2load usb 0:1 0x800000 /boot/uImage usb_boot=usb start; run load_uimage; run load_initrd; bootm 0x800000 0x2100000 bootcmd=run usb_make_boot_args ; run usb_boot; reset usb_make_boot_args=setenv bootargs console=ttyS0,115200 mtdparts=orion_nand:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10 earlyprintk=serial init=/bin/systemd stdin=serial stdout=serial stderr=serial mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no initrd_start=0x2d8000 disaMvPnp=no eth1addr=00:d0:b8:1f:50:8a enaAutoRecovery=yes pcieTune=no Environment size: 2446/16380 bytes Marvell>>
Re: Help with iomega ix4-200d installation January 12, 2020 10:31PM |
Admin Registered: 13 years ago Posts: 18,898 |
setenv bootcmd 'run flash_load'
boot
setenv bootcmd 'run flash_load' saveenv
setenv bootcmd 'run usb_make_boot_args ; run usb_boot; reset' boot
Re: Help with iomega ix4-200d installation February 07, 2020 10:15AM |
Registered: 4 years ago Posts: 10 |
Re: Help with iomega ix4-200d installation February 07, 2020 10:19AM |
Registered: 5 years ago Posts: 258 |
Re: Help with iomega ix4-200d installation February 07, 2020 03:50PM |
Admin Registered: 13 years ago Posts: 18,898 |
Quote
https://forum.doozan.com/read.php?2,12096
Updated 03 Feb 2020:
Kernel linux-5.5.1-kirkwood-tld-1 package has been uploaded.
Latest Linux kernel 5.x general release information can be found at:
LinuxChanges log
Download at Dropbox:
linux-5.5.1-kirkwood-tld-1-bodhi.tar.bz2
md5:
fb2f12ebd29d89fceab51e4e15b9b15a
sha256:
ef1c19641671a26488901b8d28fd83a0eace3c0c08e553bf7c284df6a97c6595
This tarball contains 6 files:
linux-image-5.5.1-kirkwood-tld-1_1.0_armel.deb
linux-headers-5.5.1-kirkwood-tld-1_1.0_armel.deb
config-5.5.1-kirkwood-tld-1
zImage-5.5.1-kirkwood-tld-1
linux-dtb-5.5.1-kirkwood-tld-1.tar
linux-5.5.1-kirkwood-tld-1.patch
Re: Help with iomega ix4-200d installation February 07, 2020 05:35PM |
Registered: 4 years ago Posts: 10 |
[ 152.766204] Segment Routing with IPv6 [ 411.119283] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 411.129125] ata4.00: configured for UDMA/133 [ 597.667653] ata4: limiting SATA link speed to 1.5 Gbps [ 597.999284] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 603.057743] ata4.00: qc timeout (cmd 0xec) [ 603.062572] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 603.069766] ata4.00: revalidation failed (errno=-5) [ 603.399283] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 613.617672] ata4.00: qc timeout (cmd 0xec) [ 613.622501] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 613.629722] ata4.00: revalidation failed (errno=-5) [ 613.959253] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 644.337642] ata4.00: qc timeout (cmd 0xec) [ 644.342477] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 644.349701] ata4.00: revalidation failed (errno=-5) [ 644.355303] ata4.00: disabled [ 644.689241] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.5.1-kirkwood-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6)) #1.0 PREEMPT Sat Feb 1 22:28:36 PST 2020 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: Iomega ix4-200d [ 0.000000] printk: bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 131072 [ 0.000000] Normal zone: 1024 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 131072 pages, LIFO batch:31 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyS0,115200 earlyprintk=serial mtdparts=orion_nand:0xa0000@0x0(uboot),0x10000@0xa0000(env),0x224000@0xb0000(zImage),0x224000@0x2d4000(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10 [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000] Memory: 493664K/524288K available (9216K kernel code, 926K rwdata, 3860K rodata, 1024K init, 296K bss, 30624K reserved, 0K cma-reserved) [ 0.000000] random: get_random_u32 called from ____cache_alloc+0x470/0x80c with crng_init=0 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008514] Switching to timer-based delay loop, resolution 5ns [ 0.015824] Console: colour dummy device 80x30 [ 0.021021] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.032233] pid_max: default: 32768 minimum: 301 [ 0.037879] LSM: Security Framework initializing [ 0.043364] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.051389] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.059968] *** VALIDATE tmpfs *** [ 0.064874] *** VALIDATE proc *** [ 0.069145] *** VALIDATE cgroup1 *** [ 0.073406] *** VALIDATE cgroup2 *** [ 0.077743] CPU: Testing write buffer coherency: ok [ 0.085047] Setting up static identity map for 0x100000 - 0x100058 [ 0.092222] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.098275] rcu: Hierarchical SRCU implementation. [ 0.106345] devtmpfs: initialized [ 0.115771] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.126346] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.134133] xor: measuring software checksum speed [ 0.238544] arm4regs : 1083.200 MB/sec [ 0.338545] 8regs : 650.400 MB/sec [ 0.438541] 32regs : 945.200 MB/sec [ 0.443403] xor: using function: arm4regs (1083.200 MB/sec) [ 0.449682] prandom: seed boundary self test passed [ 0.459458] prandom: 100 self tests passed [ 0.464234] pinctrl core: initialized pinctrl subsystem [ 0.471048] thermal_sys: Registered thermal governor 'step_wise' [ 0.471681] NET: Registered protocol family 16 [ 0.484239] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.492761] audit: initializing netlink subsys (disabled) [ 0.500184] audit: type=2000 audit(0.490:1): state=initialized audit_enabled=0 res=1 [ 0.508731] cpuidle: using governor ladder [ 0.513578] cpuidle: using governor menu [ 0.518768] Feroceon L2: Enabling L2 [ 0.523054] Feroceon L2: Cache support initialised. [ 0.534864] No ATAGs? [ 2.568522] random: fast init done [ 5.639026] raid6: int32x8 gen() 105 MB/s [ 5.808762] raid6: int32x8 xor() 65 MB/s [ 5.978976] raid6: int32x4 gen() 106 MB/s [ 6.148787] raid6: int32x4 xor() 68 MB/s [ 6.318682] raid6: int32x2 gen() 131 MB/s [ 6.488587] raid6: int32x2 xor() 93 MB/s [ 6.659090] raid6: int32x1 gen() 100 MB/s [ 6.828828] raid6: int32x1 xor() 68 MB/s [ 6.833768] raid6: using algorithm int32x2 gen() 131 MB/s [ 6.839851] raid6: .... xor() 93 MB/s, rmw enabled [ 6.845311] raid6: using intx1 recovery algorithm [ 6.850950] vgaarb: loaded [ 6.854924] SCSI subsystem initialized [ 6.859621] libata version 3.00 loaded. [ 6.859887] usbcore: registered new interface driver usbfs [ 6.866106] usbcore: registered new interface driver hub [ 6.872214] usbcore: registered new device driver usb [ 6.878132] pps_core: LinuxPPS API ver. 1 registered [ 6.883794] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 6.893613] PTP clock support registered [ 6.899714] clocksource: Switched to clocksource orion_clocksource [ 8.252203] *** VALIDATE bpf *** [ 8.256551] VFS: Disk quotas dquot_6.6.0 [ 8.261270] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 8.268982] *** VALIDATE ramfs *** [ 8.283792] NET: Registered protocol family 2 [ 8.289674] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 8.298797] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 8.307306] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 8.315188] TCP: Hash tables configured (established 4096 bind 4096) [ 8.322363] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 8.329570] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 8.337436] NET: Registered protocol family 1 [ 8.343210] RPC: Registered named UNIX socket transport module. [ 8.349877] RPC: Registered udp transport module. [ 8.355255] RPC: Registered tcp transport module. [ 8.360654] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 8.367762] PCI: CLS 0 bytes, default 32 [ 8.372693] Trying to unpack rootfs image as initramfs... [ 9.251118] Freeing initrd memory: 9444K [ 9.255909] NetWinder Floating Point Emulator V0.97 (double precision) [ 9.264473] Initialise system trusted keyrings [ 9.269633] Key type blacklist registered [ 9.274625] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 9.281903] zbud: loaded [ 9.286330] NFS: Registering the id_resolver key type [ 9.292159] Key type id_resolver registered [ 9.297015] Key type id_legacy registered [ 9.301740] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 9.309110] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 9.316570] jffs2: version 2.2. (NAND) (SUMMARY) \xc2\xa9 2001-2006 Red Hat, Inc. [ 9.324773] *** VALIDATE jffs2 *** [ 9.328859] fuse: init (API version 7.31) [ 9.333580] *** VALIDATE fuse *** [ 9.337576] *** VALIDATE fuse *** [ 9.341943] orangefs_debugfs_init: called with debug mask: :none: :0: [ 9.349237] orangefs_init: module version upstream loaded [ 9.355335] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 9.365162] *** VALIDATE xfs *** [ 9.418922] async_tx: api initialized (async) [ 9.424059] Key type asymmetric registered [ 9.428828] Asymmetric key parser 'x509' registered [ 9.434507] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 9.444155] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 9.453644] mvebu-gpio f1010140.gpio: IRQ index 3 not found [ 9.460560] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 9.468796] pci_bus 0000:00: root bus resource [bus 00-ff] [ 9.474991] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 9.482553] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 9.489485] pci_bus 0000:00: scanning bus [ 9.489563] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 9.496283] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 9.504667] pci_bus 0000:00: fixups for bus [ 9.504680] PCI: bus0: Fast back to back transfers disabled [ 9.510957] pci 0000:00:01.0: scanning [bus 00-00] behind bridge, pass 0 [ 9.510967] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 9.519636] pci 0000:00:01.0: scanning [bus 00-00] behind bridge, pass 1 [ 9.519805] pci_bus 0000:01: scanning bus [ 9.519851] pci 0000:01:00.0: [11ab:6121] type 00 class 0x01018f [ 9.526549] pci 0000:01:00.0: reg 0x10: [io 0x0000-0x0007] [ 9.532826] pci 0000:01:00.0: reg 0x14: [io 0xf0000008-0xf000000b] [ 9.539791] pci 0000:01:00.0: reg 0x18: [io 0x0000-0x0007] [ 9.546041] pci 0000:01:00.0: reg 0x1c: [io 0xf0000018-0xf000001b] [ 9.553002] pci 0000:01:00.0: reg 0x20: [io 0xf0000020-0xf000002f] [ 9.559964] pci 0000:01:00.0: reg 0x24: [mem 0x40000000-0x400003ff] [ 9.566975] pci 0000:01:00.0: supports D1 [ 9.571683] pci 0000:01:00.0: PME# supported from D0 D1 D3hot [ 9.578098] pci 0000:01:00.0: PME# disabled [ 9.578359] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 9.589828] pci_bus 0000:01: fixups for bus [ 9.589841] PCI: bus1: Fast back to back transfers disabled [ 9.596084] pci_bus 0000:01: bus scan returning with max=01 [ 9.596096] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 9.603411] pci_bus 0000:00: bus scan returning with max=01 [ 9.603597] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 9.611167] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff] [ 9.618189] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0100000-0xe01007ff pref] [ 9.626107] pci 0000:01:00.0: BAR 5: assigned [mem 0xe0000000-0xe00003ff] [ 9.633585] pci 0000:01:00.0: BAR 4: assigned [io 0x10000-0x1000f] [ 9.640548] pci 0000:01:00.0: BAR 0: assigned [io 0x10010-0x10017] [ 9.647481] pci 0000:01:00.0: BAR 2: assigned [io 0x10018-0x1001f] [ 9.654441] pci 0000:01:00.0: BAR 1: assigned [io 0x10020-0x10023] [ 9.661404] pci 0000:01:00.0: BAR 3: assigned [io 0x10024-0x10027] [ 9.668337] pci 0000:00:01.0: PCI bridge to [bus 01] [ 9.673997] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 9.680955] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 9.688477] pcieport 0000:00:01.0: assign IRQ: got 0 [ 9.688495] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 9.695297] pcieport 0000:00:01.0: enabling bus mastering [ 9.695797] mv_xor f1060800.xor: Marvell shared XOR driver [ 9.760768] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 9.771306] mv_xor f1060900.xor: Marvell shared XOR driver [ 9.840719] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 9.851509] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 9.859906] printk: console [ttyS0] disabled [ 9.864933] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 9.874648] printk: console [ttyS0] enabled [ 9.884499] printk: bootconsole [earlycon0] disabled [ 9.904294] loop: module loaded [ 9.908476] sata_mv f1080000.sata: version 1.28 [ 9.908748] sata_mv f1080000.sata: slots 32 ports 2 [ 9.918024] scsi host0: sata_mv [ 9.922533] scsi host1: sata_mv [ 9.926664] ata1: SATA max UDMA/133 irq 33 [ 9.931545] ata2: SATA max UDMA/133 irq 33 [ 9.937325] nand: device found, Manufacturer ID: 0xec, Chip ID: 0x75 [ 9.944534] nand: Samsung NAND 32MiB 3,3V 8-bit [ 9.949812] nand: 32 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16 [ 9.957872] Scanning device for bad blocks [ 10.300985] 5 cmdlinepart partitions found on MTD device orion_nand [ 10.307985] Creating 5 MTD partitions on "orion_nand": [ 10.313875] 0x000000000000-0x0000000a0000 : "uboot" [ 10.320975] 0x0000000a0000-0x0000000b0000 : "env" [ 10.327774] 0x0000000b0000-0x0000002d4000 : "zImage" [ 10.334944] 0x0000002d4000-0x0000004f8000 : "initrd" [ 10.342090] 0x000000000000-0x000002000000 : "flash" [ 10.351431] libphy: Fixed MDIO Bus: probed [ 10.357079] libphy: orion_mdio_bus: probed [ 10.390992] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 10.439762] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 10.451334] ata1.00: ATA-8: ST32000542AS, CC38, max UDMA/133 [ 10.457720] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 10.472072] ata1.00: configured for UDMA/133 [ 10.487588] scsi 0:0:0:0: Direct-Access ATA ST32000542AS CC38 PQ: 0 ANSI: 5 [ 10.497716] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB) [ 10.506773] sd 0:0:0:0: [sda] Write Protect is off [ 10.512371] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 10.512513] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 10.569334] sda: sda1 sda2 [ 10.574597] sd 0:0:0:0: [sda] Attached SCSI disk [ 11.009778] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 11.021366] ata2.00: ATA-8: Hitachi HUA723020ALA641, MK7OA840, max UDMA/133 [ 11.029062] ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 11.043375] ata2.00: configured for UDMA/133 [ 11.058854] scsi 1:0:0:0: Direct-Access ATA Hitachi HUA72302 A840 PQ: 0 ANSI: 5 [ 11.068967] sd 1:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB) [ 11.077871] sd 1:0:0:0: [sdb] Write Protect is off [ 11.083450] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 11.083611] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 11.110423] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:50:43:70:23:36 [ 11.120728] sdb: sdb1 sdb2 [ 11.125995] sd 1:0:0:0: [sdb] Attached SCSI disk [ 11.840409] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:50:43:70:23:37 [ 11.850050] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 11.857346] ehci-pci: EHCI PCI platform driver [ 11.862599] ehci-orion: EHCI orion driver [ 11.867543] orion-ehci f1050000.ehci: EHCI Host Controller [ 11.873820] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 11.882411] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 11.909758] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 11.916778] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.05 [ 11.925814] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 11.933792] usb usb1: Product: EHCI Host Controller [ 11.939395] usb usb1: Manufacturer: Linux 5.5.1-kirkwood-tld-1 ehci_hcd [ 11.946757] usb usb1: SerialNumber: f1050000.ehci [ 11.952875] hub 1-0:1.0: USB hub found [ 11.957381] hub 1-0:1.0: 1 port detected [ 11.962826] usbcore: registered new interface driver usb-storage [ 11.970014] mousedev: PS/2 mouse device common for all mice [ 11.977089] rtc-mv f1010300.rtc: registered as rtc0 [ 11.982911] i2c /dev entries driver [ 11.988466] device-mapper: uevent: version 1.0.3 [ 11.994171] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com [ 12.003839] device-mapper: multipath round-robin: version 1.2.0 loaded [ 12.011175] device-mapper: multipath queue-length: version 0.2.0 loaded [ 12.018519] device-mapper: multipath service-time: version 0.3.0 loaded [ 12.025977] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 12.032831] device-mapper: raid: Loading target version 1.15.0 [ 12.040343] hid: raw HID events driver (C) Jiri Kosina [ 12.046523] exFAT: Version 1.3.0 [ 12.050590] drop_monitor: Initializing network drop monitor service [ 12.057855] NET: Registered protocol family 17 [ 12.063308] Key type dns_resolver registered [ 12.068804] registered taskstats version 1 [ 12.073790] Loading compiled-in X.509 certificates [ 12.079421] zswap: loaded using pool lzo/zbud [ 12.084736] Key type ._fscrypt registered [ 12.089463] Key type .fscrypt registered [ 12.195777] Key type big_key registered [ 12.243997] Key type encrypted registered [ 12.251403] rtc-mv f1010300.rtc: setting system clock to 2020-02-07T23:14:49 UTC (1581117289) [ 12.264160] Freeing unused kernel memory: 1024K [ 12.270605] Checked W+X mappings: passed, no W+X pages found [ 12.276995] Run /init as init process [ 12.329900] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 12.391818] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice= 9.01 [ 12.401927] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 12.415967] usb 1-1: Product: USB2.0 Hub [ 12.427648] hub 1-1:1.0: USB hub found [ 12.440343] hub 1-1:1.0: 4 ports detected [ 12.769811] usb 1-1.1: new high-speed USB device number 3 using orion-ehci [ 12.822695] usb 1-1.1: New USB device found, idVendor=8564, idProduct=1000, bcdDevice=11.00 [ 12.847189] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 12.872357] usb 1-1.1: Product: Mass Storage Device [ 12.877964] usb 1-1.1: Manufacturer: JetFlash [ 12.902321] usb 1-1.1: SerialNumber: 26X4R0R0EBEQBAA5 [ 12.925670] usb-storage 1-1.1:1.0: USB Mass Storage device detected [ 12.954581] scsi host2: usb-storage 1-1.1:1.0 [ 13.186714] usbcore: registered new interface driver uas [ 13.341762] ahci 0000:01:00.0: assign IRQ: got 38 [ 13.341791] ahci 0000:01:00.0: version 3.0 [ 13.341813] pci 0000:00:01.0: enabling bus mastering [ 13.341877] ahci 0000:01:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this. [ 13.419894] ahci 0000:01:00.0: controller can't do NCQ, turning off CAP_NCQ [ 13.427593] ahci 0000:01:00.0: controller can't do PMP, turning off CAP_PMP [ 13.493263] ahci 0000:01:00.0: masking port_map 0x7 -> 0x3 [ 13.499610] ahci 0000:01:00.0: SSS flag set, parallel bus scan disabled [ 13.568081] ahci 0000:01:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode [ 13.627266] ahci 0000:01:00.0: flags: 64bit stag led slum part [ 13.687940] scsi host3: ahci [ 13.709937] scsi host4: ahci [ 13.729877] scsi host5: ahci [ 13.733883] ata3: SATA max UDMA/133 abar m1024@0xe0000000 port 0xe0000100 irq 38 [ 13.785120] ata4: SATA max UDMA/133 abar m1024@0xe0000000 port 0xe0000180 irq 38 [ 13.832034] ata5: DUMMY [ 14.181416] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 14.317150] scsi 2:0:0:0: Direct-Access JetFlash Transcend 32GB 1100 PQ: 0 ANSI: 4 [ 14.332233] sd 2:0:0:0: [sdc] 63406080 512-byte logical blocks: (32.5 GB/30.2 GiB) [ 14.346222] sd 2:0:0:0: [sdc] Write Protect is off [ 14.351872] sd 2:0:0:0: [sdc] Mode Sense: 43 00 00 00 [ 14.352456] sd 2:0:0:0: [sdc] No Caching mode page found [ 14.358501] sd 2:0:0:0: [sdc] Assuming drive cache: write through [ 14.371574] sdc: sdc1 [ 14.382723] sd 2:0:0:0: [sdc] Attached SCSI removable disk [ 19.209776] ata3.00: qc timeout (cmd 0xec) [ 19.214606] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 19.551385] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 29.929875] ata3.00: qc timeout (cmd 0xec) [ 29.934701] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 29.941551] ata3: limiting SATA link speed to 1.5 Gbps [ 30.271388] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 60.649850] ata3.00: qc timeout (cmd 0xec) [ 60.654677] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 60.991412] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 61.331418] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 61.339602] ata4.00: ATA-8: ST32000542AS, CC38, max UDMA/133 [ 61.346051] ata4.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 61.859916] ata4.00: configured for UDMA/133 [ 61.875454] scsi 4:0:0:0: Direct-Access ATA ST32000542AS CC38 PQ: 0 ANSI: 5 [ 61.886985] sd 4:0:0:0: [sdd] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB) [ 61.897374] sd 4:0:0:0: [sdd] Write Protect is off [ 61.902973] sd 4:0:0:0: [sdd] Mode Sense: 00 3a 00 00 [ 61.903118] sd 4:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 61.941271] sdd: sdd1 sdd2 [ 61.948287] sd 4:0:0:0: [sdd] Attached SCSI disk [ 92.391395] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 92.410987] ata4.00: configured for UDMA/133 [ 92.531566] random: crng init done [ 103.927357] EXT4-fs (sdc1): mounting ext3 file system using the ext4 subsystem [ 103.974486] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null) [ 106.983564] systemd-udevd[414]: Using default interface naming scheme 'v240'. [ 107.012716] systemd-udevd[395]: Using default interface naming scheme 'v240'. [ 107.052645] systemd-udevd[414]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 107.065023] systemd-udevd[395]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 107.169888] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 107.249891] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 107.271009] watchdog: f1020300.watchdog-timer: driver supplied timeout (4294967295) out of range [ 107.313068] sd 2:0:0:0: Attached scsi generic sg2 type 0 [ 107.386061] adt7475 0-002e: ADT7473 device, revision 0 [ 107.457171] sd 4:0:0:0: Attached scsi generic sg3 type 0 [ 107.468709] watchdog: f1020300.watchdog-timer: falling back to default timeout (21) [ 107.500838] adt7475 0-002e: Optional features: fan4 pwm2 [ 107.558219] orion_wdt: Initial timeout 21 sec [ 108.125104] marvell-cesa f1030000.crypto: CESA device successfully registered [ 108.297338] systemd-udevd[415]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 138.471390] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 138.480948] ata4.00: configured for UDMA/133 [ 140.541980] EXT4-fs (sdc1): re-mounted. Opts: errors=remount-ro [ 147.080111] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 152.759268] NET: Registered protocol family 10 [ 152.766204] Segment Routing with IPv6 [ 411.119283] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 411.129125] ata4.00: configured for UDMA/133 [ 597.667653] ata4: limiting SATA link speed to 1.5 Gbps [ 597.999284] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 603.057743] ata4.00: qc timeout (cmd 0xec) [ 603.062572] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 603.069766] ata4.00: revalidation failed (errno=-5) [ 603.399283] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 613.617672] ata4.00: qc timeout (cmd 0xec) [ 613.622501] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 613.629722] ata4.00: revalidation failed (errno=-5) [ 613.959253] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 644.337642] ata4.00: qc timeout (cmd 0xec) [ 644.342477] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 644.349701] ata4.00: revalidation failed (errno=-5) [ 644.355303] ata4.00: disabled [ 644.689241] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
Re: Help with iomega ix4-200d installation February 07, 2020 06:07PM |
Admin Registered: 13 years ago Posts: 18,898 |
lspci -vv
Re: Help with iomega ix4-200d installation February 07, 2020 06:12PM |
Registered: 4 years ago Posts: 10 |
root@debian:~# lspci -vv 00:01.0 PCI bridge: Marvell Technology Group Ltd. 88F6281 [Kirkwood] ARM SoC (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00010000-00010fff Memory behind bridge: e0000000-e00fffff Prefetchable memory behind bridge: 00000000-000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- [virtual] Expansion ROM at e0100000 [disabled] [size=2K] BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort+ >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0 ExtTag- RBE+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <256ns, L1 unlimited ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp- LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #0, PowerLimit 0.000W; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported ARIFwd- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd- LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- 01:00.0 IDE interface: Marvell Technology Group Ltd. 88SE6121 SATA II / PATA Controller (rev b2) (prog-if 8f [PCI native mode controller, supports both channels switched to ISA compatibility mode, supports bus mastering]) Subsystem: Marvell Technology Group Ltd. 88SE6111/6121 SATA II / PATA Controller (88SE6111/6121 1/2 port SATA II + 1 port PATA Controller) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 38 Region 0: I/O ports at 10010 [size=8] Region 1: I/O ports at 10020 [size=4] Region 2: I/O ports at 10018 [size=8] Region 3: I/O ports at 10024 [size=4] Region 4: I/O ports at 10000 [size=16] Region 5: Memory at e0000000 (32-bit, non-prefetchable) [size=1K] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [e0] Express (v1) Legacy Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr+ NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Exit Latency L0s <256ns, L1 unlimited ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 1f, GenCap- CGenEn- ChkCap- ChkEn- Kernel driver in use: ahci Kernel modules: ahci
Re: Help with iomega ix4-200d installation February 07, 2020 11:43PM |
Admin Registered: 13 years ago Posts: 18,898 |
Re: Help with iomega ix4-200d installation February 08, 2020 12:28AM |
Admin Registered: 13 years ago Posts: 18,898 |
01:00.0 IDE interface: Marvell Technology Group Ltd. 88SE6121 SATA II / PATA Controller (rev b2) (prog-if 8f [PCI native mode controller, supports both channels switched to ISA compatibility mode, supports bus mastering])
grep CONFIG_PATA_MARVELL /boot/config*
dmesg | grep -i pata
Re: Help with iomega ix4-200d installation February 08, 2020 08:11AM |
Registered: 4 years ago Posts: 10 |
root@ix4-200d:/# dmesg | grep pata root@ix4-200d:/#
root@ix4-200d:/# lspci -vv 00:01.0 IDE interface: Marvell Technology Group Ltd. Device 6121 (rev b2) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: Marvell Technology Group Ltd. Device 6121 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 9 Region 0: I/O ports at 1010 [size=8] Region 1: I/O ports at 1020 [size=4] Region 2: I/O ports at 1018 [size=8] Region 3: I/O ports at 1024 [size=4] Region 4: I/O ports at 1000 [size=16] Region 5: Memory at e8000000 (32-bit, non-prefetchable) [size=1K] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=1 PME- Capabilities: [50] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Address: 00000000 Data: 0000 Capabilities: [e0] Express (v1) Legacy Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr+ NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <256ns, L1 unlimited ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100] #11ab Capabilities: [612] #00 Capabilities: [102] #6121 Capabilities: [014] #1021 Kernel driver in use: mv_mv61xx
Linux version 2.6.22.18 (soho@bsoho149.lss.emc.com) (gcc version 4.3.2 (crosstool-NG-1.3.1) ) #1 Thu Jan 5 13:29:36 EST 2012 CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053977 Machine: Feroceon-KW Using UBoot passing parameters structure Memory policy: ECC disabled, Data cache writeback On node 0 totalpages: 131072 DMA zone: 1024 pages used for memmap DMA zone: 0 pages reserved DMA zone: 130048 pages, LIFO batch:31 Normal zone: 0 pages used for memmap CPU0: D VIVT write-back cache CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets Built 1 zonelists. Total pages: 130048 Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:0xa0000@0x0(uboot),0x10000@0xa0000(env),0x224000@0xb0000(zImage),0x224000@0x2d4000(initrd),32m@0x0(flash) PID hash table entries: 2048 (order: 11, 8192 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 256MB 256MB 0MB 0MB = 512MB total Memory: 513920KB available (3520K code, 283K data, 120K init) Calibrating delay loop... 1192.75 BogoMIPS (lpj=5963776) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 CPU Interface ------------- SDRAM_CS0 ....base 00000000, size 256MB SDRAM_CS1 ....base 10000000, size 256MB SDRAM_CS2 ....disable SDRAM_CS3 ....disable PEX0_MEM ....base e8000000, size 128MB PEX0_IO ....base f2000000, size 1MB INTER_REGS ....base f1000000, size 1MB NFLASH_CS ....base fa000000, size 2MB SPI_CS ....base f4000000, size 16MB BOOT_ROM_CS ....no such DEV_BOOTCS ....no such CRYPT_ENG ....base f0000000, size 2MB Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21)-- IX4-110 Soc: 88F6281 A1 LE Detected Tclk 200000000 and SysClk 400000000 MV Buttons Device Load Marvell USB EHCI Host controller #0: c0876600 PEX0 interface detected Link X1 PCI: bus0: Fast back to back transfers disabled SCSI Scattered Spinup: SCSI Scattered Spinup Feature Status: Enabled SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 Time: kw_clocksource clocksource has been installed. IP route cache hash table entries: 16384 (order: 4, 65536 bytes) TCP established hash table entries: 65536 (order: 7, 524288 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 65536 bind 65536) TCP reno registered checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 1788K RTC registered Use the XOR engines (acceleration) for enhancing the following functions: o RAID 5 Xor calculation o kernel memcpy o kenrel memzero Number of XOR engines to use: 4 cesadev_init(c0011e28) mvCesaInit: sessions=640, queue=64, pSram=f0000000 MV Buttons Driver Load Registering unionfs 2.5.1 (for 2.6.22.19) Installing knfsd (copyright (C) 1996 okir@monad.swb.de). io scheduler noop registered io scheduler anticipatory registered (default) Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A RAMDISK driver initialized: 16 RAM disks of 5120K size 1024 blocksize loop: module loaded Loading Marvell Ethernet Driver: o Cached descriptors in DRAM o DRAM SW cache-coherency o Single RX Queue support - ETH_DEF_RXQ=0 o Single TX Queue support - ETH_DEF_TXQ=0 o TCP segmentation offload enabled o Receive checksum offload enabled o Transmit checksum offload enabled o Network Fast Processing (Routing) supported o Driver ERROR statistics enabled o Driver INFO statistics enabled o Proc tool API enabled o Rx descripors: q0=128 o Tx descripors: q0=532 o Loading network interface(s): o eth0, ifindex = 1, GbE port = 0 o eth1, ifindex = 2, GbE port = 1 mvFpRuleDb (c0ac0000): 16384 entries, 65536 bytes e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI e100: Copyright(c) 1999-2006 Intel Corporation Marvell Storage Controller is found, using IRQ 9. scsi0 : Marvell Storage Controller scsi 0:0:0:0: Direct-Access ATA ST32000542AS CC38 PQ: 0 ANSI: 5 scsi 0:0:4:0: Direct-Access ATA ST32000542AS CC38 PQ: 0 ANSI: 5 Integrated Sata device found scsi1 : Marvell SCSI to SATA adapter scsi2 : Marvell SCSI to SATA adapter scsi 1:0:0:0: Direct-Access Seagate ST32000542AS CC38 PQ: 0 ANSI: 5 scsi 2:0:0:0: Direct-Access Hitachi HUA723020ALA641 MK7O PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 3907029168 512-byte hardware sectors (2000399 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 17 00 10 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 0:0:0:0: [sda] 3907029168 512-byte hardware sectors (2000399 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 17 00 10 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA sda: sda1 sda2 sd 0:0:0:0: [sda] Attached SCSI disk sd 0:0:4:0: [sdb] 3907029168 512-byte hardware sectors (2000399 MB) sd 0:0:4:0: [sdb] Write Protect is off sd 0:0:4:0: [sdb] Mode Sense: 17 00 10 00 sd 0:0:4:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 0:0:4:0: [sdb] 3907029168 512-byte hardware sectors (2000399 MB) sd 0:0:4:0: [sdb] Write Protect is off sd 0:0:4:0: [sdb] Mode Sense: 17 00 10 00 sd 0:0:4:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA sdb: sdb1 sdb2 sd 0:0:4:0: [sdb] Attached SCSI disk sd 1:0:0:0: [sdc] 3907029168 512-byte hardware sectors (2000399 MB) sd 1:0:0:0: [sdc] Write Protect is off sd 1:0:0:0: [sdc] Mode Sense: 23 00 10 00 sd 1:0:0:0: [sdc] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 1:0:0:0: [sdc] 3907029168 512-byte hardware sectors (2000399 MB) sd 1:0:0:0: [sdc] Write Protect is off sd 1:0:0:0: [sdc] Mode Sense: 23 00 10 00 sd 1:0:0:0: [sdc] Write cache: enabled, read cache: enabled, supports DPO and FUA sdc: sdc1 sdc2 sd 1:0:0:0: [sdc] Attached SCSI disk sd 2:0:0:0: [sdd] 3907029168 512-byte hardware sectors (2000399 MB) sd 2:0:0:0: [sdd] Write Protect is off sd 2:0:0:0: [sdd] Mode Sense: 23 00 10 00 sd 2:0:0:0: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 2:0:0:0: [sdd] 3907029168 512-byte hardware sectors (2000399 MB) sd 2:0:0:0: [sdd] Write Protect is off sd 2:0:0:0: [sdd] Mode Sense: 23 00 10 00 sd 2:0:0:0: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA sdd: sdd1 sdd2 sd 2:0:0:0: [sdd] Attached SCSI disk sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 0:0:4:0: Attached scsi generic sg1 type 0 sd 1:0:0:0: Attached scsi generic sg2 type 0 sd 2:0:0:0: Attached scsi generic sg3 type 0 NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ NAND device: Manufacturer ID: 0xec, Chip ID: 0x75 (Samsung NAND 32MiB 3,3V 8-bit) Scanning device for bad blocks 5 cmdlinepart partitions found on MTD device nand_mtd Using command line partition definition Creating 5 MTD partitions on "nand_mtd": 0x00000000-0x000a0000 : "uboot" 0x000a0000-0x000b0000 : "env" 0x000b0000-0x002d4000 : "zImage" 0x002d4000-0x004f8000 : "initrd" 0x00000000-0x02000000 : "flash" ehci_marvell ehci_marvell.70059: Marvell Orion EHCI ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver USB Universal Host Controller Interface driver v3.0 usb 1-1: new high speed USB device using ehci_marvell and address 2 usb 1-1: configuration #1 chosen from 1 choice hub 1-1:1.0: USB hub found hub 1-1:1.0: 4 ports detected usbcore: registered new interface driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice i2c /dev entries driver attach_adapter.... adt7473_detect.... adt7473 0-002e: adt7473 chip found md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 raid6: int32x1 92 MB/s raid6: int32x2 118 MB/s raid6: int32x4 130 MB/s raid6: int32x8 98 MB/s raid6: using algorithm int32x4 (130 MB/s) md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 raid5: measuring checksumming speed arm4regs : 1087.200 MB/sec 8regs : 806.000 MB/sec 32regs : 881.200 MB/sec raid5: using function: arm4regs (1087.200 MB/sec) device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com dm_crypt using the OCF package. wix gpio_init wix_lcm: WIX LCM driver version 0.1 TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. RAMDISK: Compressed image found at block 0 EXT2-fs warning: checktime reached, running e2fsck is recommended VFS: Mounted root (ext2 filesystem). md: md0 stopped. md: bind<sdc1> md: bind<sdb1> md: bind<sdd1> md: bind<sda1> raid1: raid set md0 active with 4 out of 4 mirrors ufsd: module license 'Commercial product' taints kernel. ufsd: driver 8.1 (031_A) LBD=ON with ioctl loaded at bf000000 NTFS read/write support included Hfs+/HfsX read/write support included Bluetooth: Core ver 2.11 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: HCI USB driver ver 2.9 usbcore: registered new interface driver hci_usb usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver Bluetooth: L2CAP ver 2.9 Bluetooth: L2CAP socket layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM ver 1.8 SGI XFS with ACLs, security attributes, large block numbers, no debug enabled Freeing init memory: 120K drivers/scsi/thor/linux/hba_mod.c 719:Enable/Disable Write Cache command error: parameter error:133 drivers/scsi/thor/linux/hba_mod.c 719:Enable/Disable Write Cache command error: parameter error:133 drivers/scsi/thor/linux/hba_mod.c 719:Enable/Disable Write Cache command error: parameter error:133 drivers/scsi/thor/linux/hba_mod.c 719:Enable/Disable Write Cache command error: parameter error:133 Adding 524280k swap on /boot/swapfile. Priority:-1 extents:133 across:533820k eth0: link down eth0: started eth1: started eth0: link up, full duplex, speed 1 Gbps md: md1 stopped. md: bind<sdb2> md: bind<sdc2> md: bind<sdd2> md: bind<sda2> raid5: device sda2 operational as raid disk 0 raid5: device sdd2 operational as raid disk 3 raid5: device sdc2 operational as raid disk 2 raid5: device sdb2 operational as raid disk 1 raid5: allocated 4212kB for md1 raid5: raid level 5 set md1 active with 4 out of 4 devices, algorithm 2 RAID5 conf printout: --- rd:4 wd:4 disk 0, o:1, dev:sda2 disk 1, o:1, dev:sdb2 disk 2, o:1, dev:sdc2 disk 3, o:1, dev:sdd2 Filesystem "dm-0": Disabling barriers, trial barrier write failed XFS mounting filesystem dm-0 Starting XFS recovery on filesystem: dm-0 (logdev: internal) Ending XFS recovery on filesystem: dm-0 (logdev: internal) iSCSI Enterprise Target Software - version 1.4.20.2 iscsi_trgt: Registered io type fileio iscsi_trgt: Registered io type blockio iscsi_trgt: Registered io type nullio iscsi_trgt: Removing all connections, sessions and targets eth0: link down eth1: link up, full duplex, speed 1 Gbps
root@ix4-200d:/# lsmod Module Size Used by iscsi_trgt 89140 5 xfs 526836 1 rfcomm 27184 0 l2cap 20388 3 rfcomm usbhid 24404 0 hci_usb 12028 0 bluetooth 52384 3 rfcomm,l2cap,hci_usb hfsplus 81284 0 msdos 7840 0 hfs 51204 0 udf 92332 0 isofs 24996 0 ext3 115112 0 jbd 53064 1 ext3 ufsd 594792 0
Re: Help with iomega ix4-200d installation February 08, 2020 03:55PM |
Admin Registered: 13 years ago Posts: 18,898 |
Re: Help with iomega ix4-200d installation February 08, 2020 04:13PM |
Registered: 4 years ago Posts: 10 |
Re: Help with iomega ix4-200d installation February 08, 2020 05:33PM |
Admin Registered: 13 years ago Posts: 18,898 |
/lib/modules/5.5.1-kirkwood-tld-1/kernel/drivers/ata/
# List of modules that you want to include in your initramfs. # They will be loaded at boot time in the order below. # # Syntax: module_name [args ...] # # You must run update-initramfs(8) to effect this change. # # Examples: # # raid1 # sd_mod pata_marvell
cd /boot cp -a initrd.img-5.5.1-kirkwood-tld-1 initrd.img-5.5.1-kirkwood-tld-1.bak update-initramfs -u
cp -a uInitrd uInitrd.bak mkimage -A arm -O linux -T ramdisk -C gzip -a 0x00000000 -e 0x00000000 -n initramfs-5.5.1-kirkwood-tld-1 -d initrd.img-5.5.1-kirkwood-tld-1 uInitrd sync
setenv usb_make_boot_args 'setenv bootargs console=ttyS0,115200 earlyprintk=serial mtdparts=orion_nand:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10 ahci.marvell_enable=0'
boot
Re: Help with iomega ix4-200d installation February 08, 2020 07:09PM |
Registered: 4 years ago Posts: 10 |
[ 61.031388][ T182] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 66.089757][ T182] ata3.00: qc timeout (cmd 0xec) [ 66.094589][ T182] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 66.101436][ T182] ata3.00: revalidation failed (errno=-5) [ 66.431381][ T182] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 66.440945][ T182] ata3.00: configured for UDMA/133
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** uboot_ver:v1.1.0 ** ** MARVELL BOARD: IX4-110 LE U-Boot 1.1.4 (Oct 15 2009 - 17:28:22) Marvell version: 3.4.18 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CF600 Soc: 88F6281 A1 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM CS[1] base 0x10000000 size 256MB DRAM Total size 512MB 16bit width Found 0x20 i2c device Set Power State as Always On Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:32 MB Found ADT7473, program LED ...(led_volt=90) OK Found ADT7473, program thermal/Fan ...(pwm_min=0) (pwm_max=130) (therm=67) (temp_min=60) OK Marvell Serial ATA Adapter Integrated Sata device found CPU : Marvell Feroceon (Rev 1) Found initrd at 0x2d4000 Streaming disabled Write allocate disabled Module 0 is RGMII Module 1 is RGMII USB 0: host mode PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 SCSI: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x7 impl IDE mode flags: 64bit ncq stag led pmp slum part scanning bus for devices... Device 0: (0:0) Vendor: ATA Prod.: ST32000542AS Rev: CC38 Type: Hard Disk Capacity: 1907729.0 MB = 1863.0 GB (3907029168 x 512) Device 1: (1:0) Vendor: ATA Prod.: WDC WD2500BEVS-6 Rev: 01.0 Type: Hard Disk Capacity: 238475.1 MB = 232.8 GB (488397168 x 512) Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 Marvell>> setenv usb_make_boot_args 'setenv bootargs console=ttyS0,115200 earlyprintk=serial mtdparts=orion_nand:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10' Marvell>> setenv load_initrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd' Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' Marvell>> setenv usb_boot 'usb start; run load_uimage; run load_initrd; bootm 0x800000 0x2100000' Marvell>> setenv bootcmd 'run usb_make_boot_args ; run usb_boot; run flash_load; reset' Marvell>> boot (Re)start USB... USB: scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found .... . ...... ............ ......................... ................................................... ...................................................................................................... ............................................................................................................................................................................................................ .... .............................................................................................. 5212194 bytes read .... . ...... ............ ......................... ................................................... ...................................................................................................... ............................................................................................................................................................................................................ .... .................................................................................................................................................................................................................................................................................................................................................................................................................... .... ........................................................................................................................ 9672412 bytes read ## Booting image at 00800000 ... Image Name: Linux-5.5.1-kirkwood-tld-1 Created: 2020-02-07 23:07:53 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5212130 Bytes = 5 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 02100000 ... Image Name: initramfs-5.5.1-kirkwood-tld-1 Created: 2020-02-09 0:52:36 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9672348 Bytes = 9.2 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.5.1-kirkwood-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6)) #1.0 PREEMPT Sat Feb 1 22:28:36 PST 2020 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Iomega ix4-200d [ 0.000000][ T0] printk: bootconsole [earlycon0] enabled [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 earlyprintk=serial mtdparts=orion_nand:0xa0000@0x0(uboot),0x10000@0xa0000(env),0x224000@0xb0000(zImage),0x224000@0x2d4000(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10 [ 0.000000][ T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 493660K/524288K available (9216K kernel code, 926K rwdata, 3860K rodata, 1024K init, 296K bss, 30628K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x470/0x80c with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000008][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008513][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.015822][ T0] Console: colour dummy device 80x30 [ 0.021021][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.032234][ T0] pid_max: default: 32768 minimum: 301 [ 0.037886][ T0] LSM: Security Framework initializing [ 0.043376][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.051405][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.059983][ T0] *** VALIDATE tmpfs *** [ 0.064878][ T0] *** VALIDATE proc *** [ 0.069141][ T0] *** VALIDATE cgroup1 *** [ 0.073405][ T0] *** VALIDATE cgroup2 *** [ 0.077738][ T0] CPU: Testing write buffer coherency: ok [ 0.085045][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.092221][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.098275][ T1] rcu: Hierarchical SRCU implementation. [ 0.106345][ T1] devtmpfs: initialized [ 0.115772][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.126345][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.134130][ T1] xor: measuring software checksum speed [ 0.238544][ T1] arm4regs : 1083.200 MB/sec [ 0.338546][ T1] 8regs : 650.400 MB/sec [ 0.438543][ T1] 32regs : 945.600 MB/sec [ 0.443402][ T1] xor: using function: arm4regs (1083.200 MB/sec) [ 0.449682][ T1] prandom: seed boundary self test passed [ 0.459457][ T1] prandom: 100 self tests passed [ 0.464233][ T1] pinctrl core: initialized pinctrl subsystem [ 0.471046][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.471688][ T1] NET: Registered protocol family 16 [ 0.484249][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.492772][ T1] audit: initializing netlink subsys (disabled) [ 0.500188][ T14] audit: type=2000 audit(0.490:1): state=initialized audit_enabled=0 res=1 [ 0.508729][ T1] cpuidle: using governor ladder [ 0.513578][ T1] cpuidle: using governor menu [ 0.518770][ T1] Feroceon L2: Enabling L2 [ 0.523054][ T1] Feroceon L2: Cache support initialised. [ 0.534862][ T1] No ATAGs? [ 2.568523][ C0] random: fast init done [ 5.639022][ T1] raid6: int32x8 gen() 105 MB/s [ 5.808766][ T1] raid6: int32x8 xor() 65 MB/s [ 5.978976][ T1] raid6: int32x4 gen() 106 MB/s [ 6.148788][ T1] raid6: int32x4 xor() 68 MB/s [ 6.318602][ T1] raid6: int32x2 gen() 131 MB/s [ 6.488582][ T1] raid6: int32x2 xor() 93 MB/s [ 6.659090][ T1] raid6: int32x1 gen() 100 MB/s [ 6.828828][ T1] raid6: int32x1 xor() 68 MB/s [ 6.833768][ T1] raid6: using algorithm int32x2 gen() 131 MB/s [ 6.839851][ T1] raid6: .... xor() 93 MB/s, rmw enabled [ 6.845311][ T1] raid6: using intx1 recovery algorithm [ 6.850948][ T1] vgaarb: loaded [ 6.854919][ T1] SCSI subsystem initialized [ 6.859877][ T1] usbcore: registered new interface driver usbfs [ 6.866098][ T1] usbcore: registered new interface driver hub [ 6.872206][ T1] usbcore: registered new device driver usb [ 6.878124][ T1] pps_core: LinuxPPS API ver. 1 registered [ 6.883784][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 6.893606][ T1] PTP clock support registered [ 6.899707][ T1] clocksource: Switched to clocksource orion_clocksource [ 8.252173][ T1] *** VALIDATE bpf *** [ 8.256519][ T1] VFS: Disk quotas dquot_6.6.0 [ 8.261237][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 8.268947][ T1] *** VALIDATE ramfs *** [ 8.283777][ T1] NET: Registered protocol family 2 [ 8.289653][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 8.298771][ T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 8.307279][ T1] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 8.315162][ T1] TCP: Hash tables configured (established 4096 bind 4096) [ 8.322336][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 8.329544][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 8.337409][ T1] NET: Registered protocol family 1 [ 8.343195][ T1] RPC: Registered named UNIX socket transport module. [ 8.349860][ T1] RPC: Registered udp transport module. [ 8.355237][ T1] RPC: Registered tcp transport module. [ 8.360637][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 8.367745][ T1] PCI: CLS 0 bytes, default 32 [ 8.372672][ T1] Trying to unpack rootfs image as initramfs... [ 9.251108][ T1] Freeing initrd memory: 9448K [ 9.255892][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 9.264454][ T1] Initialise system trusted keyrings [ 9.269621][ T1] Key type blacklist registered [ 9.274601][ T1] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 9.281880][ T1] zbud: loaded [ 9.286304][ T1] NFS: Registering the id_resolver key type [ 9.292127][ T1] Key type id_resolver registered [ 9.296981][ T1] Key type id_legacy registered [ 9.301705][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 9.309075][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 9.316542][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 9.324740][ T1] *** VALIDATE jffs2 *** [ 9.328824][ T1] fuse: init (API version 7.31) [ 9.333546][ T1] *** VALIDATE fuse *** [ 9.337541][ T1] *** VALIDATE fuse *** [ 9.341909][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 9.349201][ T1] orangefs_init: module version upstream loaded [ 9.355300][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 9.365133][ T1] *** VALIDATE xfs *** [ 9.421427][ T1] async_tx: api initialized (async) [ 9.426467][ T1] Key type asymmetric registered [ 9.431345][ T1] Asymmetric key parser 'x509' registered [ 9.436950][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 9.446598][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 9.456097][ T1] mvebu-gpio f1010140.gpio: IRQ index 3 not found [ 9.463015][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 9.471319][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 9.477477][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 9.485035][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 9.492064][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 9.498760][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 9.507169][ T1] PCI: bus0: Fast back to back transfers disabled [ 9.513454][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 9.522336][ T1] pci 0000:01:00.0: [11ab:6121] type 00 class 0x01018f [ 9.529038][ T1] pci 0000:01:00.0: reg 0x10: [io 0x0000-0x0007] [ 9.535315][ T1] pci 0000:01:00.0: reg 0x14: [io 0xf0000008-0xf000000b] [ 9.542279][ T1] pci 0000:01:00.0: reg 0x18: [io 0x0000-0x0007] [ 9.548529][ T1] pci 0000:01:00.0: reg 0x1c: [io 0xf0000018-0xf000001b] [ 9.555489][ T1] pci 0000:01:00.0: reg 0x20: [io 0xf0000020-0xf000002f] [ 9.562453][ T1] pci 0000:01:00.0: reg 0x24: [mem 0x40000000-0x400003ff] [ 9.569464][ T1] pci 0000:01:00.0: supports D1 [ 9.574172][ T1] pci 0000:01:00.0: PME# supported from D0 D1 D3hot [ 9.580871][ T1] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 9.592325][ T1] PCI: bus1: Fast back to back transfers disabled [ 9.598576][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 9.606078][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 9.613646][ T1] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff] [ 9.620692][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0100000-0xe01007ff pref] [ 9.628581][ T1] pci 0000:01:00.0: BAR 5: assigned [mem 0xe0000000-0xe00003ff] [ 9.636057][ T1] pci 0000:01:00.0: BAR 4: assigned [io 0x10000-0x1000f] [ 9.643018][ T1] pci 0000:01:00.0: BAR 0: assigned [io 0x10010-0x10017] [ 9.649974][ T1] pci 0000:01:00.0: BAR 2: assigned [io 0x10018-0x1001f] [ 9.656906][ T1] pci 0000:01:00.0: BAR 1: assigned [io 0x10020-0x10023] [ 9.663868][ T1] pci 0000:01:00.0: BAR 3: assigned [io 0x10024-0x10027] [ 9.670830][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 9.676464][ T1] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 9.683418][ T1] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 9.690980][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 9.698253][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 9.760756][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 9.771287][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 9.840710][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 9.851500][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 9.859888][ T1] printk: console [ttyS0] disabled [ 9.864907][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 9.874621][ T1] printk: console [ttyS0] enabled [ 9.874621][ T1] printk: console [ttyS0] enabled [ 9.884465][ T1] printk: bootconsole [earlycon0] disabled [ 9.884465][ T1] printk: bootconsole [earlycon0] disabled [ 9.904260][ T1] loop: module loaded [ 9.908712][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 9.917996][ T1] scsi host0: sata_mv [ 9.922485][ T1] scsi host1: sata_mv [ 9.926619][ T1] ata1: SATA max UDMA/133 irq 33 [ 9.931501][ T1] ata2: SATA max UDMA/133 irq 33 [ 9.937281][ T1] nand: device found, Manufacturer ID: 0xec, Chip ID: 0x75 [ 9.944491][ T1] nand: Samsung NAND 32MiB 3,3V 8-bit [ 9.949770][ T1] nand: 32 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16 [ 9.957828][ T1] Scanning device for bad blocks [ 10.271237][ T118] ata1: SATA link down (SStatus 0 SControl F300) [ 10.307220][ T1] 5 cmdlinepart partitions found on MTD device orion_nand [ 10.314234][ T1] Creating 5 MTD partitions on "orion_nand": [ 10.320124][ T1] 0x000000000000-0x0000000a0000 : "uboot" [ 10.327200][ T1] 0x0000000a0000-0x0000000b0000 : "env" [ 10.334059][ T1] 0x0000000b0000-0x0000002d4000 : "zImage" [ 10.341225][ T1] 0x0000002d4000-0x0000004f8000 : "initrd" [ 10.348334][ T1] 0x000000000000-0x000002000000 : "flash" [ 10.357685][ T1] libphy: Fixed MDIO Bus: probed [ 10.363380][ T1] libphy: orion_mdio_bus: probed [ 10.397253][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 10.621319][ T120] ata2: SATA link down (SStatus 0 SControl F300) [ 11.120372][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:50:43:70:23:36 [ 11.850356][ T1] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:50:43:70:23:37 [ 11.859977][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 11.867259][ T1] ehci-pci: EHCI PCI platform driver [ 11.872511][ T1] ehci-orion: EHCI orion driver [ 11.877428][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 11.883699][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 11.892319][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 11.919749][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 11.926786][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.05 [ 11.935827][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 11.943802][ T1] usb usb1: Product: EHCI Host Controller [ 11.949406][ T1] usb usb1: Manufacturer: Linux 5.5.1-kirkwood-tld-1 ehci_hcd [ 11.956768][ T1] usb usb1: SerialNumber: f1050000.ehci [ 11.962893][ T1] hub 1-0:1.0: USB hub found [ 11.967407][ T1] hub 1-0:1.0: 1 port detected [ 11.972880][ T1] usbcore: registered new interface driver usb-storage [ 11.980094][ T1] mousedev: PS/2 mouse device common for all mice [ 11.987145][ T1] rtc-mv f1010300.rtc: registered as rtc0 [ 11.992963][ T1] i2c /dev entries driver [ 11.998549][ T1] device-mapper: uevent: version 1.0.3 [ 12.004261][ T1] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com [ 12.013920][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 12.021252][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 12.028599][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 12.036045][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 12.042894][ T1] device-mapper: raid: Loading target version 1.15.0 [ 12.050371][ T1] hid: raw HID events driver (C) Jiri Kosina [ 12.056551][ T1] exFAT: Version 1.3.0 [ 12.060618][ T1] drop_monitor: Initializing network drop monitor service [ 12.067894][ T1] NET: Registered protocol family 17 [ 12.073350][ T1] Key type dns_resolver registered [ 12.078824][ T1] registered taskstats version 1 [ 12.083808][ T1] Loading compiled-in X.509 certificates [ 12.089443][ T1] zswap: loaded using pool lzo/zbud [ 12.094858][ T1] Key type ._fscrypt registered [ 12.099588][ T1] Key type .fscrypt registered [ 12.205784][ T1] Key type big_key registered [ 12.253971][ T1] Key type encrypted registered [ 12.261360][ T1] rtc-mv f1010300.rtc: setting system clock to 2020-02-09T00:55:21 UTC (1581209721) [ 12.274100][ T1] Freeing unused kernel memory: 1024K [ 12.280596][ T1] Checked W+X mappings: passed, no W+X pages found [ 12.286980][ T1] Run /init as init process Loading, please wait... [ 12.340212][ T129] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 12.401982][ T129] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice= 9.01 [ 12.412434][ T129] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 12.426503][ T129] usb 1-1: Product: USB2.0 Hub [ 12.438029][ T129] hub 1-1:1.0: USB hub found [ 12.450243][ T129] hub 1-1:1.0: 4 ports detected Starting version 241 [ 12.779809][ T129] usb 1-1.1: new high-speed USB device number 3 using orion-ehci [ 12.842730][ T129] usb 1-1.1: New USB device found, idVendor=8564, idProduct=1000, bcdDevice=11.00 [ 12.866708][ T129] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 12.894622][ T129] usb 1-1.1: Product: Mass Storage Device [ 12.909887][ T129] usb 1-1.1: Manufacturer: JetFlash [ 12.914972][ T129] usb 1-1.1: SerialNumber: 26X4R0R0EBEQBAA5 [ 12.944424][ T129] usb-storage 1-1.1:1.0: USB Mass Storage device detected [ 12.972416][ T129] scsi host2: usb-storage 1-1.1:1.0 [ 13.205219][ T169] usbcore: registered new interface driver uas [ 13.334824][ T169] ahci 0000:01:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this. [ 13.409828][ T169] ahci 0000:01:00.0: controller can't do NCQ, turning off CAP_NCQ [ 13.417530][ T169] ahci 0000:01:00.0: controller can't do PMP, turning off CAP_PMP [ 13.492782][ T169] ahci 0000:01:00.0: masking port_map 0x7 -> 0x3 [ 13.499160][ T169] ahci 0000:01:00.0: SSS flag set, parallel bus scan disabled [ 13.554280][ T169] ahci 0000:01:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode [ 13.600139][ T169] ahci 0000:01:00.0: flags: 64bit stag led slum part [ 13.648260][ T169] scsi host3: ahci [ 13.669931][ T169] scsi host4: ahci [ 13.687380][ T169] scsi host5: ahci [ 13.702172][ T169] ata3: SATA max UDMA/133 abar m1024@0xe0000000 port 0xe0000100 irq 38 [ 13.741873][ T169] ata4: SATA max UDMA/133 abar m1024@0xe0000000 port 0xe0000180 irq 38 [ 13.779599][ T169] ata5: DUMMY [ 14.121461][ T182] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 14.130212][ T182] ata3.00: ATA-8: ST32000542AS, CC38, max UDMA/133 [ 14.136601][ T182] ata3.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 14.145616][ T182] ata3.00: configured for UDMA/133 [ 14.160754][ T22] scsi: waiting for bus probes to complete ... [ 14.318186][ T188] scsi 2:0:0:0: Direct-Access JetFlash Transcend 32GB 1100 PQ: 0 ANSI: 4 [ 14.332384][ T22] scsi 3:0:0:0: Direct-Access ATA ST32000542AS CC38 PQ: 0 ANSI: 5 [ 14.343652][ T188] sd 2:0:0:0: [sda] 63406080 512-byte logical blocks: (32.5 GB/30.2 GiB) [ 14.357751][ T190] sd 3:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB) [ 14.368769][ T190] sd 3:0:0:0: [sdb] Write Protect is off [ 14.374618][ T188] sd 2:0:0:0: [sda] Write Protect is off [ 14.380275][ T190] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 14.392156][ T188] sd 2:0:0:0: [sda] No Caching mode page found [ 14.398226][ T188] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 14.412855][ T188] sda: sda1 [ 14.417539][ T190] sdb: sdb1 sdb2 [ 14.432874][ T188] sd 2:0:0:0: [sda] Attached SCSI removable disk [ 14.439815][ T190] sd 3:0:0:0: [sdb] Attached SCSI disk [ 14.701561][ T184] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 14.708925][ T184] ata4.00: ATA-8: WDC WD2500BEVS-60UST0, 01.01A01, max UDMA/100 [ 14.716479][ T184] ata4.00: 488397168 sectors, multi 0: LBA48 [ 14.722993][ T184] ata4.00: configured for UDMA/100 [ 14.738502][ T7] scsi 4:0:0:0: Direct-Access ATA WDC WD2500BEVS-6 1A01 PQ: 0 ANSI: 5 [ 14.749769][ T190] sd 4:0:0:0: [sdc] 488397168 512-byte logical blocks: (250 GB/233 GiB) [ 14.760013][ T190] sd 4:0:0:0: [sdc] Write Protect is off [ 14.765698][ T190] sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 14.827295][ T190] sdc: sdc1 sdc2 sdc3 [ 14.835681][ T190] sd 4:0:0:0: [sdc] Attached SCSI disk Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.33.1 [/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1 rootfs: clean, 18096/1982464 files, 423040/7925504 blocks (check in 3 mounts) done. [ 27.007392][ T211] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 27.055149][ T211] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.93 booting [[36minfo[39;49m] Using makefile-style concurrent boot in runlevel S. [....] Starting hotplug events dispatcher: systemd-udevd [?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0c. [....] Synthesizing the initial hotplug events (subsystems)...[?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0cdone. [....] Synthesizing the initial hotplug events (devices)...[?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0cdone. [ 29.948808][ C0] random: crng init done [....] Waiting for /dev to be fully populated...[ 30.123692][ T396] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 30.135458][ T414] systemd-udevd[414]: Using default interface naming scheme 'v240'. [ 30.152591][ T394] systemd-udevd[394]: Using default interface naming scheme 'v240'. [ 30.194070][ T396] sd 3:0:0:0: Attached scsi generic sg1 type 0 [ 30.253167][ T396] sd 4:0:0:0: Attached scsi generic sg2 type 0 [ 30.270577][ T414] systemd-udevd[414]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 30.282543][ T394] systemd-udevd[394]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 30.410263][ T397] adt7475 0-002e: ADT7473 device, revision 0 [ 30.416157][ T397] adt7475 0-002e: Optional features: fan4 pwm2 [ 30.464347][ T416] watchdog: f1020300.watchdog-timer: driver supplied timeout (4294967295) out of range [ 30.587401][ T416] watchdog: f1020300.watchdog-timer: falling back to default timeout (21) [ 30.744624][ T416] orion_wdt: Initial timeout 21 sec [ 31.324287][ T415] marvell-cesa f1030000.crypto: CESA device successfully registered [ 31.356548][ T394] systemd-udevd[394]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 61.031388][ T182] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 66.089757][ T182] ata3.00: qc timeout (cmd 0xec) [ 66.094589][ T182] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 66.101436][ T182] ata3.00: revalidation failed (errno=-5) [ 66.431381][ T182] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 66.440945][ T182] ata3.00: configured for UDMA/133 [?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0cdone. [....] Setting hostname to 'debian'...[?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0cdone. [....] Activating swap:[?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0c. [ 68.500393][ T656] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [[36minfo[39;49m] Will now check all file systems. fsck from util-linux 2.33.1 Checking all file systems. LABEL=rootfs is mounted [....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.[?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0c. [....] Cleaning up temporary files...[....] Cleaning /tmp...[?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0cdone. /tmp[?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0c. [....] Will now mount local filesystems:[?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0c. [....] Will now activate swapfile swap:[?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0cdone. [....] Checking minimum space in /tmp...[?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0cdone. [....] Cleaning up temporary files...[?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0c. [....] Starting Setting kernel variables: sysctl[?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0c. [....] Initializing random number generator...[?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0cdone. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:50:43:70:23:36 Sending on LPF/eth0/00:50:43:70:23:36 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3 [ 74.888519][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7 DHCPOFFER of 192.168.1.191 from 192.168.1.1 DHCPREQUEST for 192.168.1.191 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.1.191 from 192.168.1.1 bound to 192.168.1.191 -- renewal in 21332 seconds. [ 79.358876][ T1211] NET: Registered protocol family 10 [ 79.365800][ T1211] Segment Routing with IPv6 [?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0cdone. [....] Starting RPC port mapper daemon: rpcbind[?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0c. [....] Starting NFS common utilities: statd idmapd[?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0c. [....] Cleaning up temporary files...[?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0c. INIT: Entering runlevel: 2 [[36minfo[39;49m] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1422 (syslogd) [?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0c. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1449 (klogd) [?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0c. [....] Starting system message bus: dbus[?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0c. [....] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon[?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0c. [....] Starting NFS common utilities: statd idmapd[?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0c. [....] Not starting NFS kernel daemon: no exports. ...[?25l[?1c7[1G[[33mwarn[39;49m8[?25h[?0c[33m(warning).[39;49m [....] Starting NTP server: ntpd[?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0c. [....] Starting OpenBSD Secure Shell server: sshd[?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0c. [....] Running local boot scripts (/etc/rc.local)[?25l[?1c7[1G[[32m ok[39;49m8[?25h[?0c. Debian GNU/Linux 10 debian ttyS0 debian login: root Password: Last login: Sat Feb 8 16:32:46 PST 2020 on ttyS0 Linux debian 5.5.1-kirkwood-tld-1 #1.0 PREEMPT Sat Feb 1 22:28:36 PST 2020 armv5tel The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@debian:~# lsmod Module Size Used by ipv6 442368 32 nf_defrag_ipv6 16384 1 ipv6 marvell_cesa 36864 0 orion_wdt 16384 0 adt7475 28672 0 hwmon_vid 16384 1 adt7475 sg 28672 0 uio_pdrv_genirq 16384 0 uio 20480 1 uio_pdrv_genirq pata_marvell 16384 0 ahci 24576 0 libahci 32768 1 ahci uas 20480 0 root@debian:~# ls -la /lib/modules/5.5.1-kirkwood-tld-1/kernel/drivers/ata/ total 208 drwxr-xr-x 2 root root 4096 Feb 8 16:25 . drwxr-xr-x 55 root root 4096 Feb 7 15:05 .. -rw-r--r-- 1 root root 13256 Feb 1 22:27 acard-ahci.ko -rw-r--r-- 1 root root 50904 Feb 1 22:27 ahci.ko -rw-r--r-- 1 root root 9324 Feb 1 22:27 ahci_mvebu.ko -rw-r--r-- 1 root root 41232 Feb 1 22:27 libahci.ko -rw-r--r-- 1 root root 20004 Feb 1 22:27 libahci_platform.ko -rw-r--r-- 1 root root 12784 Feb 1 22:27 pata_atp867x.ko -rw-r--r-- 1 root root 9384 Feb 8 16:25 pata_marvell.ko -rw-r--r-- 1 root root 8788 Feb 1 22:27 pata_piccolo.ko -rw-r--r-- 1 root root 11688 Feb 1 22:27 pata_rdc.ko root@debian:~# cat /etc/initramfs-tools/modules # List of modules that you want to include in your initramfs. # They will be loaded at boot time in the order below. # # Syntax: module_name [args ...] # # You must run update-initramfs(8) to effect this change. # # Examples: # # raid1 # sd_mod pata_marvell root@debian:~# hdparm -I /dev/sda /dev/sda: SG_IO: bad/missing sense data, sb[]: 70 00 05 00 00 00 00 0a 00 00 00 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ATA device, with non-removable media Standards: Likely used: 1 Configuration: Logical max current cylinders 0 0 heads 0 0 sectors/track 0 0 -- Logical/Physical Sector size: 512 bytes device size with M = 1024*1024: 0 MBytes device size with M = 1000*1000: 0 MBytes cache/buffer size = unknown Capabilities: IORDY not likely Cannot perform double-word IO R/W multiple sector transfer: not supported DMA: not supported PIO: pio0 root@debian:~# hdparm -I /dev/sdb /dev/sdb: [ 166.631263][ T182] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 166.641109][ T182] ata3.00: configured for UDMA/133 SG_IO: bad/missing sense data, sb[]: 70 00 05 00 00 00 00 0a 00 40 00 00 21 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ATA device, with non-removable media Model Number: ST32000542AS Serial Number: 6XW1JBFS Firmware Revision: CC38 Transport: Serial Standards: Used: unknown (minor revision code 0x0029) Supported: 8 7 6 5 Likely used: 8 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 3907029168 Logical/Physical Sector size: 512 bytes device size with M = 1024*1024: 1907729 MBytes device size with M = 1000*1000: 2000398 MBytes (2000 GB) cache/buffer size = unknown Nominal Media Rotation Rate: 5900 Capabilities: LBA, IORDY(can be disabled) Queue depth: 32 Standby timer values: spec'd by Standard, no device specific minimum R/W multiple sector transfer: Max = 16 Current = ? Advanced power management level: 254 Recommended acoustic management value: 254, current value: 0 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * SMART feature set Security Mode feature set * Power Management feature set * Write cache * Look-ahead * Host Protected Area feature set * WRITE_BUFFER command * READ_BUFFER command * DOWNLOAD_MICROCODE * Advanced Power Management feature set Power-Up In Standby feature set SET_FEATURES required to spinup after power up SET_MAX security extension * Automatic Acoustic Management feature set * 48-bit Address feature set * Device Configuration Overlay feature set * Mandatory FLUSH_CACHE * FLUSH_CACHE_EXT * SMART error logging * SMART self-test * General Purpose Logging feature set * WRITE_{DMA|MULTIPLE}_FUA_EXT * 64-bit World wide name Write-Read-Verify feature set * WRITE_UNCORRECTABLE_EXT command * {READ,WRITE}_DMA_EXT_GPL commands * Segmented DOWNLOAD_MICROCODE * Gen1 signaling speed (1.5Gb/s) * Gen2 signaling speed (3.0Gb/s) * Native Command Queueing (NCQ) * Phy event counters Device-initiated interface power management * Software settings preservation * SMART Command Transport (SCT) feature set * SCT Read/Write Long (AC1), obsolete * SCT Write Same (AC2) * SCT Error Recovery Control (AC3) * SCT Features Control (AC4) * SCT Data Tables (AC5) unknown 206[12] (vendor specific) Security: Master password revision code = 65534 supported not enabled not locked not frozen not expired: security count supported: enhanced erase 368min for SECURITY ERASE UNIT. 368min for ENHANCED SECURITY ERASE UNIT. Logical Unit WWN Device Identifier: 5000c50022810ff7 NAA : 5 IEEE OUI : 000c50 Unique ID : 022810ff7 Checksum: correct root@debian:~# hdparm -I /dev/sdc /dev/sdc: ATA device, with non-removable media Model Number: WDC WD2500BEVS-60UST0 Serial Number: WD-WXE508CH5322 Firmware Revision: 01.01A01 Standards: Supported: 8 7 6 5 Likely used: 8 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 488397168 Logical/Physical Sector size: 512 bytes device size with M = 1024*1024: 238475 MBytes device size with M = 1000*1000: 250059 MBytes (250 GB) cache/buffer size = 8192 KBytes Capabilities: LBA, IORDY(can be disabled) Standby timer values: spec'd by Standard, with device specific minimum R/W multiple sector transfer: Max = 16 Current = 0 Advanced power management level: 254 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * SMART feature set Security Mode feature set * Power Management feature set * Write cache * Look-ahead * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * DOWNLOAD_MICROCODE * Advanced Power Management feature set * 48-bit Address feature set * Device Configuration Overlay feature set * Mandatory FLUSH_CACHE * FLUSH_CACHE_EXT * SMART error logging * SMART self-test * General Purpose Logging feature set * 64-bit World wide name * IDLE_IMMEDIATE with UNLOAD * WRITE_UNCORRECTABLE_EXT command * Segmented DOWNLOAD_MICROCODE * Gen1 signaling speed (1.5Gb/s) * Phy event counters Device-initiated interface power management * Software settings preservation * SMART Command Transport (SCT) feature set * SCT Read/Write Long (AC1), obsolete * SCT Write Same (AC2) * SCT Error Recovery Control (AC3) * SCT Features Control (AC4) * SCT Data Tables (AC5) unknown 206[12] (vendor specific) unknown 206[13] (vendor specific) Security: Master password revision code = 65534 supported not enabled not locked not frozen not expired: security count supported: enhanced erase 92min for SECURITY ERASE UNIT. 92min for ENHANCED SECURITY ERASE UNIT. Logical Unit WWN Device Identifier: 50014ee2ac3c635a NAA : 5 IEEE OUI : 0014ee Unique ID : 2ac3c635a Checksum: correct root@debian:~#
Re: Help with iomega ix4-200d installation February 08, 2020 08:15PM |
Admin Registered: 13 years ago Posts: 18,898 |
Quote
And reboot.
Interrupt serial console, and
And then enter the envs like you did before. This time change the usb_make_boot_args:
setenv usb_make_boot_args 'setenv bootargs console=ttyS0,115200 earlyprintk=serial mtdparts=orion_nand:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10 ahci.marvell_enable=0'
And then
boot
Re: Help with iomega ix4-200d installation February 08, 2020 08:43PM |
Registered: 4 years ago Posts: 10 |
[ 13.363549][ T170] scsi host3: pata_marvell [ 13.394828][ T170] scsi host4: pata_marvell [ 13.399472][ T170] ata3: PATA max UDMA/100 cmd 0x10010 ctl 0x10020 bmdma 0x10000 irq 38 [ 13.467951][ T170] ata4: PATA max UDMA/133 cmd 0x10018 ctl 0x10024 bmdma 0x10008 irq 38
Marvell>> setenv usb_make_boot_args 'setenv bootargs console=ttyS0,115200 earlyprintk=serial mtdparts=orion_nand:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10 ahci.marvell_enable=0' Marvell>> setenv load_initrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd' Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' Marvell>> setenv usb_boot 'usb start; run load_uimage; run load_initrd; bootm 0x800000 0x2100000' Marvell>> setenv bootcmd 'run usb_make_boot_args ; run usb_boot; run flash_load; reset' Marvell>> boot (Re)start USB... USB: scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found .... . ...... ............ ......................... ................................................... ...................................................................................................... ............................................................................................................................................................................................................ .... .............................................................................................. 5212194 bytes read .... . ...... ............ ......................... ................................................... ...................................................................................................... ............................................................................................................................................................................................................ .... .................................................................................................................................................................................................................................................................................................................................................................................................................... .... ........................................................................................................................ 9672412 bytes read ## Booting image at 00800000 ... Image Name: Linux-5.5.1-kirkwood-tld-1 Created: 2020-02-07 23:07:53 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5212130 Bytes = 5 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 02100000 ... Image Name: initramfs-5.5.1-kirkwood-tld-1 Created: 2020-02-09 0:52:36 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9672348 Bytes = 9.2 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.5.1-kirkwood-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6)) #1.0 PREEMPT Sat Feb 1 22:28:36 PST 2020 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Iomega ix4-200d [ 0.000000][ T0] printk: bootconsole [earlycon0] enabled [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 earlyprintk=serial mtdparts=orion_nand:0xa0000@0x0(uboot),0x10000@0xa0000(env),0x224000@0xb0000(zImage),0x224000@0x2d4000(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10 ahci.marvell_enable=0 [ 0.000000][ T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 493660K/524288K available (9216K kernel code, 926K rwdata, 3860K rodata, 1024K init, 296K bss, 30628K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x470/0x80c with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000009][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008522][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.015832][ T0] Console: colour dummy device 80x30 [ 0.021031][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.032244][ T0] pid_max: default: 32768 minimum: 301 [ 0.037892][ T0] LSM: Security Framework initializing [ 0.043384][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.051407][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.059984][ T0] *** VALIDATE tmpfs *** [ 0.064886][ T0] *** VALIDATE proc *** [ 0.069154][ T0] *** VALIDATE cgroup1 *** [ 0.073415][ T0] *** VALIDATE cgroup2 *** [ 0.077758][ T0] CPU: Testing write buffer coherency: ok [ 0.085073][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.092257][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.098315][ T1] rcu: Hierarchical SRCU implementation. [ 0.106378][ T1] devtmpfs: initialized [ 0.115859][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.126430][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.134218][ T1] xor: measuring software checksum speed [ 0.238552][ T1] arm4regs : 1083.200 MB/sec [ 0.338554][ T1] 8regs : 650.400 MB/sec [ 0.438552][ T1] 32regs : 945.600 MB/sec [ 0.443411][ T1] xor: using function: arm4regs (1083.200 MB/sec) [ 0.449691][ T1] prandom: seed boundary self test passed [ 0.459457][ T1] prandom: 100 self tests passed [ 0.464233][ T1] pinctrl core: initialized pinctrl subsystem [ 0.471048][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.471682][ T1] NET: Registered protocol family 16 [ 0.484281][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.492799][ T1] audit: initializing netlink subsys (disabled) [ 0.500219][ T14] audit: type=2000 audit(0.490:1): state=initialized audit_enabled=0 res=1 [ 0.508764][ T1] cpuidle: using governor ladder [ 0.513613][ T1] cpuidle: using governor menu [ 0.518846][ T1] Feroceon L2: Enabling L2 [ 0.523132][ T1] Feroceon L2: Cache support initialised. [ 0.534959][ T1] No ATAGs? [ 2.568530][ C0] random: fast init done [ 5.639041][ T1] raid6: int32x8 gen() 105 MB/s [ 5.808764][ T1] raid6: int32x8 xor() 65 MB/s [ 5.978990][ T1] raid6: int32x4 gen() 106 MB/s [ 6.148798][ T1] raid6: int32x4 xor() 68 MB/s [ 6.318862][ T1] raid6: int32x2 gen() 132 MB/s [ 6.488603][ T1] raid6: int32x2 xor() 93 MB/s [ 6.659103][ T1] raid6: int32x1 gen() 100 MB/s [ 6.828837][ T1] raid6: int32x1 xor() 68 MB/s [ 6.833777][ T1] raid6: using algorithm int32x2 gen() 132 MB/s [ 6.839860][ T1] raid6: .... xor() 93 MB/s, rmw enabled [ 6.845319][ T1] raid6: using intx1 recovery algorithm [ 6.850956][ T1] vgaarb: loaded [ 6.854932][ T1] SCSI subsystem initialized [ 6.859892][ T1] usbcore: registered new interface driver usbfs [ 6.866121][ T1] usbcore: registered new interface driver hub [ 6.872224][ T1] usbcore: registered new device driver usb [ 6.878141][ T1] pps_core: LinuxPPS API ver. 1 registered [ 6.883802][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 6.893624][ T1] PTP clock support registered [ 6.899766][ T1] clocksource: Switched to clocksource orion_clocksource [ 8.252877][ T1] *** VALIDATE bpf *** [ 8.257220][ T1] VFS: Disk quotas dquot_6.6.0 [ 8.261937][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 8.269646][ T1] *** VALIDATE ramfs *** [ 8.284420][ T1] NET: Registered protocol family 2 [ 8.290348][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 8.299388][ T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 8.307916][ T1] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 8.315806][ T1] TCP: Hash tables configured (established 4096 bind 4096) [ 8.323007][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 8.330248][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 8.338096][ T1] NET: Registered protocol family 1 [ 8.343872][ T1] RPC: Registered named UNIX socket transport module. [ 8.350543][ T1] RPC: Registered udp transport module. [ 8.355920][ T1] RPC: Registered tcp transport module. [ 8.361320][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 8.368428][ T1] PCI: CLS 0 bytes, default 32 [ 8.373355][ T1] Trying to unpack rootfs image as initramfs... [ 9.251795][ T1] Freeing initrd memory: 9448K [ 9.256625][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 9.265191][ T1] Initialise system trusted keyrings [ 9.270433][ T1] Key type blacklist registered [ 9.275323][ T1] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 9.282600][ T1] zbud: loaded [ 9.287027][ T1] NFS: Registering the id_resolver key type [ 9.292858][ T1] Key type id_resolver registered [ 9.297715][ T1] Key type id_legacy registered [ 9.302464][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 9.309861][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 9.317306][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 9.325509][ T1] *** VALIDATE jffs2 *** [ 9.329594][ T1] fuse: init (API version 7.31) [ 9.334315][ T1] *** VALIDATE fuse *** [ 9.338309][ T1] *** VALIDATE fuse *** [ 9.342678][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 9.350006][ T1] orangefs_init: module version upstream loaded [ 9.356070][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 9.365905][ T1] *** VALIDATE xfs *** [ 9.419829][ T1] async_tx: api initialized (async) [ 9.424870][ T1] Key type asymmetric registered [ 9.429639][ T1] Asymmetric key parser 'x509' registered [ 9.435313][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 9.444942][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 9.454477][ T1] mvebu-gpio f1010140.gpio: IRQ index 3 not found [ 9.461396][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 9.469634][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 9.475862][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 9.483428][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 9.490458][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 9.497153][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 9.505564][ T1] PCI: bus0: Fast back to back transfers disabled [ 9.511847][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 9.520727][ T1] pci 0000:01:00.0: [11ab:6121] type 00 class 0x01018f [ 9.527422][ T1] pci 0000:01:00.0: reg 0x10: [io 0x0000-0x0007] [ 9.533699][ T1] pci 0000:01:00.0: reg 0x14: [io 0xf0000008-0xf000000b] [ 9.540663][ T1] pci 0000:01:00.0: reg 0x18: [io 0x0000-0x0007] [ 9.546914][ T1] pci 0000:01:00.0: reg 0x1c: [io 0xf0000018-0xf000001b] [ 9.553874][ T1] pci 0000:01:00.0: reg 0x20: [io 0xf0000020-0xf000002f] [ 9.560838][ T1] pci 0000:01:00.0: reg 0x24: [mem 0x40000000-0x400003ff] [ 9.567848][ T1] pci 0000:01:00.0: supports D1 [ 9.572556][ T1] pci 0000:01:00.0: PME# supported from D0 D1 D3hot [ 9.579236][ T1] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 9.590685][ T1] PCI: bus1: Fast back to back transfers disabled [ 9.596935][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 9.604433][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 9.612009][ T1] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff] [ 9.619027][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0100000-0xe01007ff pref] [ 9.626946][ T1] pci 0000:01:00.0: BAR 5: assigned [mem 0xe0000000-0xe00003ff] [ 9.634423][ T1] pci 0000:01:00.0: BAR 4: assigned [io 0x10000-0x1000f] [ 9.641386][ T1] pci 0000:01:00.0: BAR 0: assigned [io 0x10010-0x10017] [ 9.648327][ T1] pci 0000:01:00.0: BAR 2: assigned [io 0x10018-0x1001f] [ 9.655288][ T1] pci 0000:01:00.0: BAR 1: assigned [io 0x10020-0x10023] [ 9.662251][ T1] pci 0000:01:00.0: BAR 3: assigned [io 0x10024-0x10027] [ 9.669184][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 9.674845][ T1] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 9.681801][ T1] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 9.689344][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 9.696647][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 9.760807][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 9.771344][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 9.840767][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 9.851556][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 9.859943][ T1] printk: console [ttyS0] disabled [ 9.864968][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 9.874683][ T1] printk: console [ttyS0] enabled [ 9.874683][ T1] printk: console [ttyS0] enabled [ 9.884534][ T1] printk: bootconsole [earlycon0] disabled [ 9.884534][ T1] printk: bootconsole [earlycon0] disabled [ 9.904326][ T1] loop: module loaded [ 9.908777][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 9.918068][ T1] scsi host0: sata_mv [ 9.922557][ T1] scsi host1: sata_mv [ 9.926688][ T1] ata1: SATA max UDMA/133 irq 33 [ 9.931571][ T1] ata2: SATA max UDMA/133 irq 33 [ 9.937344][ T1] nand: device found, Manufacturer ID: 0xec, Chip ID: 0x75 [ 9.944551][ T1] nand: Samsung NAND 32MiB 3,3V 8-bit [ 9.949831][ T1] nand: 32 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16 [ 9.957890][ T1] Scanning device for bad blocks [ 10.271297][ T118] ata1: SATA link down (SStatus 0 SControl F300) [ 10.307305][ T1] 5 cmdlinepart partitions found on MTD device orion_nand [ 10.314322][ T1] Creating 5 MTD partitions on "orion_nand": [ 10.320211][ T1] 0x000000000000-0x0000000a0000 : "uboot" [ 10.327283][ T1] 0x0000000a0000-0x0000000b0000 : "env" [ 10.334134][ T1] 0x0000000b0000-0x0000002d4000 : "zImage" [ 10.341291][ T1] 0x0000002d4000-0x0000004f8000 : "initrd" [ 10.348395][ T1] 0x000000000000-0x000002000000 : "flash" [ 10.357745][ T1] libphy: Fixed MDIO Bus: probed [ 10.363444][ T1] libphy: orion_mdio_bus: probed [ 10.397021][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 10.621384][ T120] ata2: SATA link down (SStatus 0 SControl F300) [ 11.120448][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:50:43:70:23:36 [ 11.850423][ T1] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:50:43:70:23:37 [ 11.860051][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 11.867339][ T1] ehci-pci: EHCI PCI platform driver [ 11.872592][ T1] ehci-orion: EHCI orion driver [ 11.877514][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 11.883785][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 11.892445][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 11.919807][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 11.926835][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.05 [ 11.935869][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 11.943847][ T1] usb usb1: Product: EHCI Host Controller [ 11.949448][ T1] usb usb1: Manufacturer: Linux 5.5.1-kirkwood-tld-1 ehci_hcd [ 11.956812][ T1] usb usb1: SerialNumber: f1050000.ehci [ 11.962934][ T1] hub 1-0:1.0: USB hub found [ 11.967442][ T1] hub 1-0:1.0: 1 port detected [ 11.972906][ T1] usbcore: registered new interface driver usb-storage [ 11.980116][ T1] mousedev: PS/2 mouse device common for all mice [ 11.987177][ T1] rtc-mv f1010300.rtc: registered as rtc0 [ 11.992991][ T1] i2c /dev entries driver [ 11.998566][ T1] device-mapper: uevent: version 1.0.3 [ 12.004277][ T1] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com [ 12.013933][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 12.021274][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 12.028616][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 12.036066][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 12.042920][ T1] device-mapper: raid: Loading target version 1.15.0 [ 12.050398][ T1] hid: raw HID events driver (C) Jiri Kosina [ 12.056584][ T1] exFAT: Version 1.3.0 [ 12.060658][ T1] drop_monitor: Initializing network drop monitor service [ 12.067934][ T1] NET: Registered protocol family 17 [ 12.073384][ T1] Key type dns_resolver registered [ 12.078900][ T1] registered taskstats version 1 [ 12.083885][ T1] Loading compiled-in X.509 certificates [ 12.089518][ T1] zswap: loaded using pool lzo/zbud [ 12.094934][ T1] Key type ._fscrypt registered [ 12.099666][ T1] Key type .fscrypt registered [ 12.205646][ T1] Key type big_key registered [ 12.253742][ T1] Key type encrypted registered [ 12.261133][ T1] rtc-mv f1010300.rtc: setting system clock to 2020-02-09T02:29:39 UTC (1581215379) [ 12.273880][ T1] Freeing unused kernel memory: 1024K [ 12.280660][ T1] Checked W+X mappings: passed, no W+X pages found [ 12.287049][ T1] Run /init as init process Loading, please wait... [ 12.339905][ T129] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 12.402704][ T129] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice= 9.01 [ 12.417856][ T129] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 12.431751][ T129] usb 1-1: Product: USB2.0 Hub [ 12.450662][ T129] hub 1-1:1.0: USB hub found [ 12.459870][ T129] hub 1-1:1.0: 4 ports detected Starting version 241 [ 12.789852][ T129] usb 1-1.1: new high-speed USB device number 3 using orion-ehci [ 12.852479][ T129] usb 1-1.1: New USB device found, idVendor=8564, idProduct=1000, bcdDevice=11.00 [ 12.878284][ T129] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 12.903753][ T129] usb 1-1.1: Product: Mass Storage Device [ 12.909365][ T129] usb 1-1.1: Manufacturer: JetFlash [ 12.936857][ T129] usb 1-1.1: SerialNumber: 26X4R0R0EBEQBAA5 [ 12.952839][ T129] usb-storage 1-1.1:1.0: USB Mass Storage device detected [ 12.989883][ T129] scsi host2: usb-storage 1-1.1:1.0 [ 13.214244][ T170] usbcore: registered new interface driver uas [ 13.363549][ T170] scsi host3: pata_marvell [ 13.394828][ T170] scsi host4: pata_marvell [ 13.399472][ T170] ata3: PATA max UDMA/100 cmd 0x10010 ctl 0x10020 bmdma 0x10000 irq 38 [ 13.467951][ T170] ata4: PATA max UDMA/133 cmd 0x10018 ctl 0x10024 bmdma 0x10008 irq 38 [ 14.329939][ T22] scsi 2:0:0:0: Direct-Access JetFlash Transcend 32GB 1100 PQ: 0 ANSI: 4 [ 14.344397][ T7] sd 2:0:0:0: [sda] 63406080 512-byte logical blocks: (32.5 GB/30.2 GiB) [ 14.358507][ T7] sd 2:0:0:0: [sda] Write Protect is off [ 14.364742][ T7] sd 2:0:0:0: [sda] No Caching mode page found [ 14.370890][ T7] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 14.383981][ T7] sda: sda1 [ 14.402751][ T7] sd 2:0:0:0: [sda] Attached SCSI removable disk Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.33.1 [/sbin/fsck.ext3 (1) -- /dev/sda1] fsck.ext3 -a -C0 /dev/sda1 rootfs: clean, 18097/1982464 files, 423044/7925504 blocks (check after next mount) done. [ 25.907391][ T204] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem [ 25.955524][ T204] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.93 booting [[36minfo[39;49m] Using makefile-style concurrent boot in runlevel S. [....] Starting hotplug events dispatcher: systemd-udevd[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Synthesizing the initial hotplug events (subsystems)...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Synthesizing the initial hotplug events (devices)...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Waiting for /dev to be fully populated...[ 28.885149][ T399] systemd-udevd[399]: Using default interface naming scheme 'v240'. [ 29.011592][ T390] systemd-udevd[390]: Using default interface naming scheme 'v240'. [ 29.028543][ T399] systemd-udevd[399]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 29.131829][ T390] systemd-udevd[390]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 29.187436][ T397] watchdog: f1020300.watchdog-timer: driver supplied timeout (4294967295) out of range [ 29.227892][ T391] adt7475 0-002e: ADT7473 device, revision 0 [ 29.331129][ T397] watchdog: f1020300.watchdog-timer: falling back to default timeout (21) [ 29.348382][ T391] adt7475 0-002e: Optional features: fan4 pwm2 [ 29.493212][ T397] orion_wdt: Initial timeout 21 sec [ 29.753676][ T391] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 30.001053][ T411] systemd-udevd[411]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 30.027496][ T398] marvell-cesa f1030000.crypto: CESA device successfully registered [ 30.444109][ C0] random: crng init done [?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Setting hostname to 'debian'...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Activating swap:[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [ 32.451390][ T633] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [[36minfo[39;49m] Will now check all file systems. fsck from util-linux 2.33.1 Checking all file systems. LABEL=rootfs is mounted [....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Cleaning up temporary files...[....] Cleaning /tmp...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. /tmp[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Will now mount local filesystems:[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Will now activate swapfile swap:[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Checking minimum space in /tmp...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Cleaning up temporary files...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting Setting kernel variables: sysctl[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Initializing random number generator...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:50:43:70:23:36 Sending on LPF/eth0/00:50:43:70:23:36 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 19 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 14 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 15 No DHCPOFFERS received. No working leases in persistent database - sleeping. [?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Starting RPC port mapper daemon: rpcbind[ 98.823910][ T1239] NET: Registered protocol family 10 [ 98.830657][ T1239] Segment Routing with IPv6 [?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting NFS common utilities: statd idmapd[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Cleaning up temporary files...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. INIT: Entering runlevel: 2 [[36minfo[39;49m] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1380 (syslogd) [?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1407 (klogd) [?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting system message bus: dbus[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting NFS common utilities: statd idmapd[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Not starting NFS kernel daemon: no exports. ...[?25l[?1c7[1G[[33mwarn[39;49m8[?25h[?0c [33m(warning).[39;49m [....] Starting NTP server: ntpd[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting OpenBSD Secure Shell server: sshd[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Running local boot scripts (/etc/rc.local)[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. Debian GNU/Linux 10 debian ttyS0 debian login: root Password: Last login: Sat Feb 8 18:26:20 PST 2020 on ttyS0 Linux debian 5.5.1-kirkwood-tld-1 #1.0 PREEMPT Sat Feb 1 22:28:36 PST 2020 armv5tel The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@debian:~# lsmod Module Size Used by ipv6 442368 30 nf_defrag_ipv6 16384 1 ipv6 sg 28672 0 marvell_cesa 36864 0 adt7475 28672 0 hwmon_vid 16384 1 adt7475 orion_wdt 16384 0 uio_pdrv_genirq 16384 0 uio 20480 1 uio_pdrv_genirq pata_marvell 16384 0 ahci 24576 0 libahci 32768 1 ahci uas 20480 0 root@debian:~# fdisk -l Disk /dev/mtdblock0: 640 KiB, 655360 bytes, 1280 sectors [0mUnits: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes [1mDisk /dev/mtdblock1: 64 KiB, 65536 bytes, 128 sectors [0mUnits: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes [1mDisk /dev/mtdblock2: 2.1 MiB, 2244608 bytes, 4384 sectors [0mUnits: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes [1mDisk /dev/mtdblock3: 2.1 MiB, 2244608 bytes, 4384 sectors [0mUnits: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes [1mDisk /dev/mtdblock4: 32 MiB, 33554432 bytes, 65536 sectors [0mUnits: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes [1mDisk /dev/sda: 30.2 GiB, 32463912960 bytes, 63406080 sectors [0mDisk model: Transcend 32GB Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0xfb8b47bf [1mDevice[0m [1mBoot[0m [1mStart[0m [1m End[0m [1m Sectors[0m [1m Size[0m [1mId[0m [1mType[0m /dev/sda1 2048 63406079 63404032 30.2G 83 Linux root@debian:~# hdparm -I /dev/sdb /dev/sdb: No such file or directory root@debian:~# hdparm -I /dev/sdc /dev/sdc: No such file or directory
Re: Help with iomega ix4-200d installation February 09, 2020 08:10PM |
Admin Registered: 13 years ago Posts: 18,898 |
Re: Help with iomega ix4-200d installation February 11, 2020 03:38PM |
Registered: 4 years ago Posts: 10 |
Re: Help with iomega ix4-200d installation February 11, 2020 04:16PM |
Admin Registered: 13 years ago Posts: 18,898 |
Re: Help with iomega ix4-200d installation February 11, 2020 07:18PM |
Registered: 4 years ago Posts: 10 |
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** uboot_ver:v1.1.0 ** ** MARVELL BOARD: IX4-110 LE U-Boot 1.1.4 (Oct 15 2009 - 17:28:22) Marvell version: 3.4.18 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CF600 Soc: 88F6281 A1 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM CS[1] base 0x10000000 size 256MB DRAM Total size 512MB 16bit width Found 0x20 i2c device Set Power State as Always On Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:32 MB Found ADT7473, program LED ...(led_volt=90) OK Found ADT7473, program thermal/Fan ...(pwm_min=0) (pwm_max=130) (therm=67) (temp_min=60) OK Marvell Serial ATA Adapter Integrated Sata device found [0 0 0]: Enable DMA mode (5) Device 0 @ 0 0: Model: TOSHIBA MK7559GSXP Firm: GN001A Ser#: Z1ACP0CAT Type: Hard Disk Supports 48-bit addressing Capacity: 715404.8 MB = 698.6 GB (1465149168 x 512) [0 1 0]: Enable DMA mode (5) Device 1 @ 0 1: Model: SAMSUNG HM120JI Firm: YF100-18 Ser#: S09GJ10LC66556 Type: Hard Disk Supports 48-bit addressing Capacity: 114473.4 MB = 111.7 GB (234441648 x 512) CPU : Marvell Feroceon (Rev 1) Found initrd at 0x2d4000 Streaming disabled Write allocate disabled Module 0 is RGMII Module 1 is RGMII USB 0: host mode PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 SCSI: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x7 impl IDE mode flags: 64bit ncq stag led pmp slum part scanning bus for devices... Device 0: (0:0) Vendor: ATA Prod.: WDC WD2500KS-00M Rev: 02.0 Type: Hard Disk Capacity: 238475.1 MB = 232.8 GB (488397168 x 512) Device 1: (1:0) Vendor: ATA Prod.: WDC WD2500BEVS-6 Rev: 01.0 Type: Hard Disk Capacity: 238475.1 MB = 232.8 GB (488397168 x 512) Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 1 0 Marvell>> setenv usb_make_boot_args 'setenv bootargs console=ttyS0,115200 earlyprintk=serial mtdparts=orion_nand:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10' Marvell>> setenv load_initrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd' Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' Marvell>> setenv usb_boot 'usb start; run load_uimage; run load_initrd; bootm 0x800000 0x2100000' Marvell>> setenv bootcmd 'run usb_make_boot_args ; run usb_boot; run flash_load; reset' Marvell>> boot (Re)start USB... USB: scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found .... . ...... ............ ......................... ................................................... ...................................................................................................... ............................................................................................................................................................................................................ .... .............................................................................................. 5212194 bytes read .... . ...... ............ ......................... ................................................... ...................................................................................................... ............................................................................................................................................................................................................ .... .................................................................................................................................................................................................................................................................................................................................................................................................................... .... ........................................................................................................................ 9672526 bytes read ## Booting image at 00800000 ... Image Name: Linux-5.5.1-kirkwood-tld-1 Created: 2020-02-07 23:07:53 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5212130 Bytes = 5 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 02100000 ... Image Name: initramfs-5.5.1-kirkwood-tld-1 Created: 2020-02-10 0:20:06 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9672462 Bytes = 9.2 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.5.1-kirkwood-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6)) #1.0 PREEMPT Sat Feb 1 22:28:36 PST 2020 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Iomega ix4-200d [ 0.000000][ T0] printk: bootconsole [earlycon0] enabled [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 earlyprintk=serial mtdparts=orion_nand:0xa0000@0x0(uboot),0x10000@0xa0000(env),0x224000@0xb0000(zImage),0x224000@0x2d4000(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10 [ 0.000000][ T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 493660K/524288K available (9216K kernel code, 926K rwdata, 3860K rodata, 1024K init, 296K bss, 30628K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x470/0x80c with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000008][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008513][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.015822][ T0] Console: colour dummy device 80x30 [ 0.021012][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.032226][ T0] pid_max: default: 32768 minimum: 301 [ 0.037879][ T0] LSM: Security Framework initializing [ 0.043373][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.051398][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.059977][ T0] *** VALIDATE tmpfs *** [ 0.064872][ T0] *** VALIDATE proc *** [ 0.069143][ T0] *** VALIDATE cgroup1 *** [ 0.073407][ T0] *** VALIDATE cgroup2 *** [ 0.077739][ T0] CPU: Testing write buffer coherency: ok [ 0.085052][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.092229][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.098283][ T1] rcu: Hierarchical SRCU implementation. [ 0.106349][ T1] devtmpfs: initialized [ 0.115798][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.126371][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.134156][ T1] xor: measuring software checksum speed [ 0.238544][ T1] arm4regs : 1083.200 MB/sec [ 0.338546][ T1] 8regs : 650.400 MB/sec [ 0.438542][ T1] 32regs : 945.600 MB/sec [ 0.443403][ T1] xor: using function: arm4regs (1083.200 MB/sec) [ 0.449683][ T1] prandom: seed boundary self test passed [ 0.459456][ T1] prandom: 100 self tests passed [ 0.464224][ T1] pinctrl core: initialized pinctrl subsystem [ 0.471039][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.471672][ T1] NET: Registered protocol family 16 [ 0.484231][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.492758][ T1] audit: initializing netlink subsys (disabled) [ 0.500192][ T14] audit: type=2000 audit(0.490:1): state=initialized audit_enabled=0 res=1 [ 0.508741][ T1] cpuidle: using governor ladder [ 0.513586][ T1] cpuidle: using governor menu [ 0.518780][ T1] Feroceon L2: Enabling L2 [ 0.523063][ T1] Feroceon L2: Cache support initialised. [ 0.534873][ T1] No ATAGs? [ 2.568522][ C0] random: fast init done [ 5.639018][ T1] raid6: int32x8 gen() 105 MB/s [ 5.808765][ T1] raid6: int32x8 xor() 65 MB/s [ 5.978973][ T1] raid6: int32x4 gen() 106 MB/s [ 6.148789][ T1] raid6: int32x4 xor() 68 MB/s [ 6.318806][ T1] raid6: int32x2 gen() 132 MB/s [ 6.488589][ T1] raid6: int32x2 xor() 93 MB/s [ 6.659091][ T1] raid6: int32x1 gen() 100 MB/s [ 6.828828][ T1] raid6: int32x1 xor() 68 MB/s [ 6.833769][ T1] raid6: using algorithm int32x2 gen() 132 MB/s [ 6.839852][ T1] raid6: .... xor() 93 MB/s, rmw enabled [ 6.845311][ T1] raid6: using intx1 recovery algorithm [ 6.850952][ T1] vgaarb: loaded [ 6.854934][ T1] SCSI subsystem initialized [ 6.859892][ T1] usbcore: registered new interface driver usbfs [ 6.866115][ T1] usbcore: registered new interface driver hub [ 6.872222][ T1] usbcore: registered new device driver usb [ 6.878142][ T1] pps_core: LinuxPPS API ver. 1 registered [ 6.883801][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 6.893623][ T1] PTP clock support registered [ 6.899718][ T1] clocksource: Switched to clocksource orion_clocksource [ 8.252823][ T1] *** VALIDATE bpf *** [ 8.257171][ T1] VFS: Disk quotas dquot_6.6.0 [ 8.261894][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 8.269604][ T1] *** VALIDATE ramfs *** [ 8.284415][ T1] NET: Registered protocol family 2 [ 8.290345][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 8.299380][ T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 8.307909][ T1] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 8.315798][ T1] TCP: Hash tables configured (established 4096 bind 4096) [ 8.322999][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 8.330239][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 8.338076][ T1] NET: Registered protocol family 1 [ 8.343858][ T1] RPC: Registered named UNIX socket transport module. [ 8.350526][ T1] RPC: Registered udp transport module. [ 8.355902][ T1] RPC: Registered tcp transport module. [ 8.361302][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 8.368410][ T1] PCI: CLS 0 bytes, default 32 [ 8.373342][ T1] Trying to unpack rootfs image as initramfs... [ 9.251835][ T1] Freeing initrd memory: 9448K [ 9.256625][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 9.265185][ T1] Initialise system trusted keyrings [ 9.270427][ T1] Key type blacklist registered [ 9.275321][ T1] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 9.282597][ T1] zbud: loaded [ 9.287020][ T1] NFS: Registering the id_resolver key type [ 9.292850][ T1] Key type id_resolver registered [ 9.297707][ T1] Key type id_legacy registered [ 9.302456][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 9.309852][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 9.317295][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 9.325491][ T1] *** VALIDATE jffs2 *** [ 9.329576][ T1] fuse: init (API version 7.31) [ 9.334298][ T1] *** VALIDATE fuse *** [ 9.338293][ T1] *** VALIDATE fuse *** [ 9.342660][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 9.349988][ T1] orangefs_init: module version upstream loaded [ 9.356053][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 9.365893][ T1] *** VALIDATE xfs *** [ 9.420807][ T1] async_tx: api initialized (async) [ 9.425846][ T1] Key type asymmetric registered [ 9.430717][ T1] Asymmetric key parser 'x509' registered [ 9.436327][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 9.445975][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 9.455462][ T1] mvebu-gpio f1010140.gpio: IRQ index 3 not found [ 9.462386][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 9.470688][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 9.476846][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 9.484405][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 9.491434][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 9.498129][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 9.506538][ T1] PCI: bus0: Fast back to back transfers disabled [ 9.512824][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 9.521703][ T1] pci 0000:01:00.0: [11ab:6121] type 00 class 0x01018f [ 9.528399][ T1] pci 0000:01:00.0: reg 0x10: [io 0x0000-0x0007] [ 9.534676][ T1] pci 0000:01:00.0: reg 0x14: [io 0xf0000008-0xf000000b] [ 9.541640][ T1] pci 0000:01:00.0: reg 0x18: [io 0x0000-0x0007] [ 9.547890][ T1] pci 0000:01:00.0: reg 0x1c: [io 0xf0000018-0xf000001b] [ 9.554851][ T1] pci 0000:01:00.0: reg 0x20: [io 0xf0000020-0xf000002f] [ 9.561814][ T1] pci 0000:01:00.0: reg 0x24: [mem 0x40000000-0x400003ff] [ 9.568826][ T1] pci 0000:01:00.0: supports D1 [ 9.573533][ T1] pci 0000:01:00.0: PME# supported from D0 D1 D3hot [ 9.580234][ T1] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 9.591691][ T1] PCI: bus1: Fast back to back transfers disabled [ 9.597945][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 9.605448][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 9.613016][ T1] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff] [ 9.620061][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0100000-0xe01007ff pref] [ 9.627951][ T1] pci 0000:01:00.0: BAR 5: assigned [mem 0xe0000000-0xe00003ff] [ 9.635426][ T1] pci 0000:01:00.0: BAR 4: assigned [io 0x10000-0x1000f] [ 9.642388][ T1] pci 0000:01:00.0: BAR 0: assigned [io 0x10010-0x10017] [ 9.649330][ T1] pci 0000:01:00.0: BAR 2: assigned [io 0x10018-0x1001f] [ 9.656291][ T1] pci 0000:01:00.0: BAR 1: assigned [io 0x10020-0x10023] [ 9.663254][ T1] pci 0000:01:00.0: BAR 3: assigned [io 0x10024-0x10027] [ 9.670216][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 9.675850][ T1] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 9.682805][ T1] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 9.690366][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 9.697641][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 9.760759][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 9.771297][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 9.840720][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 9.851503][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 9.859890][ T1] printk: console [ttyS0] disabled [ 9.864916][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 9.874632][ T1] printk: console [ttyS0] enabled [ 9.874632][ T1] printk: console [ttyS0] enabled [ 9.884480][ T1] printk: bootconsole [earlycon0] disabled [ 9.884480][ T1] printk: bootconsole [earlycon0] disabled [ 9.904287][ T1] loop: module loaded [ 9.908734][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 9.918030][ T1] scsi host0: sata_mv [ 9.922524][ T1] scsi host1: sata_mv [ 9.926654][ T1] ata1: SATA max UDMA/133 irq 33 [ 9.931537][ T1] ata2: SATA max UDMA/133 irq 33 [ 9.937320][ T1] nand: device found, Manufacturer ID: 0xec, Chip ID: 0x75 [ 9.944523][ T1] nand: Samsung NAND 32MiB 3,3V 8-bit [ 9.949805][ T1] nand: 32 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16 [ 9.957863][ T1] Scanning device for bad blocks [ 10.300925][ T1] 5 cmdlinepart partitions found on MTD device orion_nand [ 10.307924][ T1] Creating 5 MTD partitions on "orion_nand": [ 10.313815][ T1] 0x000000000000-0x0000000a0000 : "uboot" [ 10.320930][ T1] 0x0000000a0000-0x0000000b0000 : "env" [ 10.327726][ T1] 0x0000000b0000-0x0000002d4000 : "zImage" [ 10.334893][ T1] 0x0000002d4000-0x0000004f8000 : "initrd" [ 10.342029][ T1] 0x000000000000-0x000002000000 : "flash" [ 10.351369][ T1] libphy: Fixed MDIO Bus: probed [ 10.357015][ T1] libphy: orion_mdio_bus: probed [ 10.391136][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 10.439766][ T118] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 10.839799][ T118] ata1.00: ATA-8: TOSHIBA MK7559GSXP, GN001A, max UDMA/100 [ 10.846884][ T118] ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 10.859191][ T118] ata1.00: configured for UDMA/100 [ 10.874729][ T7] scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK7559GS 1A PQ: 0 ANSI: 5 [ 10.884840][ T122] sd 0:0:0:0: [sda] 1465149168 512-byte logical blocks: (750 GB/699 GiB) [ 10.893646][ T122] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 10.899777][ T122] sd 0:0:0:0: [sda] Write Protect is off [ 10.905430][ T122] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 11.120431][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:50:43:70:23:36 [ 11.380924][ T122] sda: sda1 sda2 [ 11.386303][ T122] sd 0:0:0:0: [sda] Attached SCSI disk [ 11.391734][ T120] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl F300) [ 11.429861][ T120] ata2.00: ATA-7: SAMSUNG HM120JI, YF100-18, max UDMA/100 [ 11.436861][ T120] ata2.00: 234441648 sectors, multi 0: LBA48 [ 11.469859][ T120] ata2.00: configured for UDMA/100 [ 11.485350][ T22] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HM120JI 0-18 PQ: 0 ANSI: 5 [ 11.495451][ T122] sd 1:0:0:0: [sdb] 234441648 512-byte logical blocks: (120 GB/112 GiB) [ 11.504084][ T122] sd 1:0:0:0: [sdb] Write Protect is off [ 11.509775][ T122] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 11.850425][ T1] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:50:43:70:23:37 [ 11.860063][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 11.867344][ T1] ehci-pci: EHCI PCI platform driver [ 11.872599][ T1] ehci-orion: EHCI orion driver [ 11.877524][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 11.883796][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 11.892453][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 11.919761][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 11.926783][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.05 [ 11.935816][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 11.943795][ T1] usb usb1: Product: EHCI Host Controller [ 11.949668][ T1] usb usb1: Manufacturer: Linux 5.5.1-kirkwood-tld-1 ehci_hcd [ 11.957051][ T1] usb usb1: SerialNumber: f1050000.ehci [ 11.962558][ T122] sdb: sdb1 sdb2 sdb3 < sdb5 > [ 11.968235][ T1] hub 1-0:1.0: USB hub found [ 11.974750][ T122] sd 1:0:0:0: [sdb] Attached SCSI disk [ 11.980209][ T1] hub 1-0:1.0: 1 port detected [ 11.985659][ T1] usbcore: registered new interface driver usb-storage [ 11.992893][ T1] mousedev: PS/2 mouse device common for all mice [ 12.000050][ T1] rtc-mv f1010300.rtc: registered as rtc0 [ 12.005804][ T1] i2c /dev entries driver [ 12.011420][ T1] device-mapper: uevent: version 1.0.3 [ 12.017052][ T1] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com [ 12.026732][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 12.034075][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 12.041465][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 12.048869][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 12.055720][ T1] device-mapper: raid: Loading target version 1.15.0 [ 12.063214][ T1] hid: raw HID events driver (C) Jiri Kosina [ 12.069396][ T1] exFAT: Version 1.3.0 [ 12.073467][ T1] drop_monitor: Initializing network drop monitor service [ 12.080762][ T1] NET: Registered protocol family 17 [ 12.086181][ T1] Key type dns_resolver registered [ 12.091951][ T1] registered taskstats version 1 [ 12.096771][ T1] Loading compiled-in X.509 certificates [ 12.102421][ T1] zswap: loaded using pool lzo/zbud [ 12.107695][ T1] Key type ._fscrypt registered [ 12.112457][ T1] Key type .fscrypt registered [ 12.218740][ T1] Key type big_key registered [ 12.267129][ T1] Key type encrypted registered [ 12.274548][ T1] rtc-mv f1010300.rtc: setting system clock to 2020-02-12T00:08:22 UTC (1581466102) [ 12.287362][ T1] Freeing unused kernel memory: 1024K [ 12.310516][ T1] Checked W+X mappings: passed, no W+X pages found [ 12.316907][ T1] Run /init as init process [ 12.349823][ T130] usb 1-1: new high-speed USB device number 2 using orion-ehci Loading, please wait... [ 12.411867][ T130] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice= 9.01 [ 12.423903][ T130] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 12.437451][ T130] usb 1-1: Product: USB2.0 Hub [ 12.448360][ T130] hub 1-1:1.0: USB hub found [ 12.454747][ T130] hub 1-1:1.0: 4 ports detected Starting version 241 [ 12.779807][ T130] usb 1-1.1: new high-speed USB device number 3 using orion-ehci [ 12.842736][ T130] usb 1-1.1: New USB device found, idVendor=8564, idProduct=1000, bcdDevice=11.00 [ 12.865467][ T130] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 12.891762][ T130] usb 1-1.1: Product: Mass Storage Device [ 12.897366][ T130] usb 1-1.1: Manufacturer: JetFlash [ 12.922575][ T130] usb 1-1.1: SerialNumber: 26X4R0R0EBEQBAA5 [ 12.946654][ T130] usb-storage 1-1.1:1.0: USB Mass Storage device detected [ 12.976086][ T130] scsi host2: usb-storage 1-1.1:1.0 [ 13.240200][ T173] usbcore: registered new interface driver uas [ 13.392483][ T173] ahci 0000:01:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this. [ 13.469107][ T173] ahci 0000:01:00.0: controller can't do NCQ, turning off CAP_NCQ [ 13.510494][ T173] ahci 0000:01:00.0: controller can't do PMP, turning off CAP_PMP [ 13.518196][ T173] ahci 0000:01:00.0: masking port_map 0x7 -> 0x3 [ 13.571634][ T173] ahci 0000:01:00.0: SSS flag set, parallel bus scan disabled [ 13.579035][ T173] ahci 0000:01:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode [ 13.663510][ T173] ahci 0000:01:00.0: flags: 64bit stag led slum part [ 13.719903][ T173] scsi host3: ahci [ 13.738624][ T173] scsi host4: ahci [ 13.759895][ T173] scsi host5: ahci [ 13.763884][ T173] ata3: SATA max UDMA/133 abar m1024@0xe0000000 port 0xe0000100 irq 38 [ 13.807750][ T173] ata4: SATA max UDMA/133 abar m1024@0xe0000000 port 0xe0000180 irq 38 [ 13.844907][ T173] ata5: DUMMY [ 14.171529][ T185] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 14.179048][ T185] ata3.00: ATA-7: WDC WD2500KS-00MJB0, 02.01C03, max UDMA/133 [ 14.186423][ T185] ata3.00: 488397168 sectors, multi 0: LBA48 [ 14.193045][ T185] ata3.00: configured for UDMA/133 [ 14.208170][ T122] scsi: waiting for bus probes to complete ... [ 14.336444][ T123] scsi 2:0:0:0: Direct-Access JetFlash Transcend 32GB 1100 PQ: 0 ANSI: 4 [ 14.350696][ T122] scsi 3:0:0:0: Direct-Access ATA WDC WD2500KS-00M 1C03 PQ: 0 ANSI: 5 [ 14.360776][ T123] sd 2:0:0:0: [sdc] 63406080 512-byte logical blocks: (32.5 GB/30.2 GiB) [ 14.376010][ T193] sd 3:0:0:0: [sdd] 488397168 512-byte logical blocks: (250 GB/233 GiB) [ 14.386865][ T123] sd 2:0:0:0: [sdc] Write Protect is off [ 14.392618][ T193] sd 3:0:0:0: [sdd] Write Protect is off [ 14.398378][ T193] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 14.408505][ T123] sd 2:0:0:0: [sdc] No Caching mode page found [ 14.418039][ T123] sd 2:0:0:0: [sdc] Assuming drive cache: write through [ 14.426683][ T193] sdd: sdd1 [ 14.434884][ T193] sd 3:0:0:0: [sdd] Attached SCSI disk [ 14.440625][ T123] sdc: sdc1 [ 14.452892][ T123] sd 2:0:0:0: [sdc] Attached SCSI removable disk [ 14.721500][ T187] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 14.728863][ T187] ata4.00: ATA-8: WDC WD2500BEVS-60UST0, 01.01A01, max UDMA/100 [ 14.736425][ T187] ata4.00: 488397168 sectors, multi 0: LBA48 [ 14.742932][ T187] ata4.00: configured for UDMA/100 [ 14.758468][ T22] scsi 4:0:0:0: Direct-Access ATA WDC WD2500BEVS-6 1A01 PQ: 0 ANSI: 5 [ 14.769796][ T123] sd 4:0:0:0: [sde] 488397168 512-byte logical blocks: (250 GB/233 GiB) [ 14.780068][ T123] sd 4:0:0:0: [sde] Write Protect is off [ 14.785753][ T123] sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 15.099133][ T123] sde: sde1 sde2 sde3 [ 15.107625][ T123] sd 4:0:0:0: [sde] Attached SCSI disk [ 16.210661][ C0] random: crng init done Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.33.1 [/sbin/fsck.ext3 (1) -- /dev/sdc1] fsck.ext3 -a -C0 /dev/sdc1 rootfs: clean, 225131/1982464 files, 1584904/7925504 blocks done. [ 28.647401][ T215] EXT4-fs (sdc1): mounting ext3 file system using the ext4 subsystem [ 28.694786][ T215] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.93 booting [[36minfo[39;49m] Using makefile-style concurrent boot in runlevel S. [....] Starting hotplug events dispatcher: systemd-udevd[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Synthesizing the initial hotplug events (subsystems)...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Synthesizing the initial hotplug events (devices)...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Waiting for /dev to be fully populated...[ 31.795900][ T402] systemd-udevd[402]: Using default interface naming scheme 'v240'. [ 31.840139][ T401] systemd-udevd[401]: Using default interface naming scheme 'v240'. [ 31.921698][ T401] systemd-udevd[401]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 31.934004][ T402] systemd-udevd[402]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 31.956723][ T428] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 32.030499][ T428] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 32.061389][ T430] adt7475 0-002e: ADT7473 device, revision 0 [ 32.081921][ T428] sd 2:0:0:0: Attached scsi generic sg2 type 0 [ 32.111113][ T430] adt7475 0-002e: Optional features: fan4 pwm2 [ 32.169915][ T428] sd 3:0:0:0: Attached scsi generic sg3 type 0 [ 32.185929][ T431] watchdog: f1020300.watchdog-timer: driver supplied timeout (4294967295) out of range [ 32.240240][ T428] sd 4:0:0:0: Attached scsi generic sg4 type 0 [ 32.381538][ T431] watchdog: f1020300.watchdog-timer: falling back to default timeout (21) [ 32.500132][ T431] orion_wdt: Initial timeout 21 sec [ 32.985189][ T432] marvell-cesa f1030000.crypto: CESA device successfully registered [ 33.314280][ T430] systemd-udevd[430]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Setting hostname to 'debian'...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Activating swap:[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [ 39.331648][ T680] EXT4-fs (sdc1): re-mounted. Opts: errors=remount-ro [[36minfo[39;49m] Will now check all file systems. fsck from util-linux 2.33.1 Checking all file systems. LABEL=rootfs is mounted [....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Cleaning up temporary files...[....] Cleaning /tmp...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. /tmp[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Will now mount local filesystems:[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Will now activate swapfile swap:[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Checking minimum space in /tmp...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Cleaning up temporary files...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting Setting kernel variables: sysctl[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Initializing random number generator...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:50:43:70:23:36 Sending on LPF/eth0/00:50:43:70:23:36 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7 [ 46.024595][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12 DHCPOFFER of 192.168.1.191 from 192.168.1.1 DHCPREQUEST for 192.168.1.191 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.1.191 from 192.168.1.1 bound to 192.168.1.191 -- renewal in 3352 seconds. [ 53.039868][ T1233] NET: Registered protocol family 10 [ 53.046708][ T1233] Segment Routing with IPv6 [?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Starting RPC port mapper daemon: rpcbind[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting NFS common utilities: statd idmapd[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Cleaning up temporary files...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. INIT: Entering runlevel: 2 [[36minfo[39;49m] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1451 (syslogd) [?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1478 (klogd) [?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting system message bus: dbus[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting NFS common utilities: statd idmapd[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Not starting NFS kernel daemon: no exports. ...[?25l[?1c7[1G[[33mwarn[39;49m8[?25h[?0c [33m(warning).[39;49m [....] Starting NTP server: ntpd[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting OpenBSD Secure Shell server: sshd[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Running local boot scripts (/etc/rc.local)[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. Debian GNU/Linux 10 debian ttyS0
Re: Help with iomega ix4-200d installation February 11, 2020 08:12PM |
Registered: 5 years ago Posts: 258 |
Re: Help with iomega ix4-200d installation February 11, 2020 09:12PM |
Admin Registered: 13 years ago Posts: 18,898 |
[ 13.469107][ T173] ahci 0000:01:00.0: controller can't do NCQ, turning off CAP_NCQ [ 13.510494][ T173] ahci 0000:01:00.0: controller can't do PMP, turning off CAP_PMP [ 13.518196][ T173] ahci 0000:01:00.0: masking port_map 0x7 -> 0x3 [ 13.571634][ T173] ahci 0000:01:00.0: SSS flag set, parallel bus scan disabled [ 13.579035][ T173] ahci 0000:01:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode
Re: Help with iomega ix4-200d installation February 12, 2020 04:36PM |
Registered: 4 years ago Posts: 10 |
lenovoemc-lifeline-fosskit-20120827.zip\EMCLifeline-GPL-Bellagio\Lifeline_OSSKit\kernel\linux-2.6.31.8\ix4-200d
_ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** uboot_ver:v1.1.0 ** ** MARVELL BOARD: IX4-110 LE U-Boot 1.1.4 (Oct 15 2009 - 17:28:22) Marvell version: 3.4.18 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CF600 Soc: 88F6281 A1 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM CS[1] base 0x10000000 size 256MB DRAM Total size 512MB 16bit width Found 0x20 i2c device Set Power State as Always On Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:32 MB Found ADT7473, program LED ...(led_volt=90) OK Found ADT7473, program thermal/Fan ...(pwm_min=0) (pwm_max=130) (therm=67) (temp_min=60) OK Marvell Serial ATA Adapter Integrated Sata device found [0 0 0]: Enable DMA mode (5) Device 0 @ 0 0: Model: TOSHIBA MK7559GSXP Firm: GN001A Ser#: Z1ACP0CAT Type: Hard Disk Supports 48-bit addressing Capacity: 715404.8 MB = 698.6 GB (1465149168 x 512) [0 1 0]: Enable DMA mode (5) Device 1 @ 0 1: Model: SAMSUNG HM120JI Firm: YF100-18 Ser#: S09GJ10LC66556 Type: Hard Disk Supports 48-bit addressing Capacity: 114473.4 MB = 111.7 GB (234441648 x 512) CPU : Marvell Feroceon (Rev 1) Found initrd at 0x2d4000 Streaming disabled Write allocate disabled Module 0 is RGMII Module 1 is RGMII USB 0: host mode PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 SCSI: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x7 impl IDE mode flags: 64bit ncq stag led pmp slum part scanning bus for devices... Device 0: (0:0) Vendor: ATA Prod.: WDC WD2500KS-00M Rev: 02.0 Type: Hard Disk Capacity: 238475.1 MB = 232.8 GB (488397168 x 512) Device 1: (1:0) Vendor: ATA Prod.: Hitachi HUA72302 Rev: MK7O Type: Hard Disk Capacity: 1907729.0 MB = 1863.0 GB (3907029168 x 512) Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 1 0 Marvell>> setenv usb_make_boot_args 'setenv bootargs console=ttyS0,115200 earlyprintk=serial mtdparts=orion_nand:$(uboot_size)@$(uboot_start)(uboot),$(env_size)@$(env_start)(env),$(kernel_size)@$(kernel_start)(zImage),$(initrd_size)@$(initrd_start)(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10' Marvell>> setenv load_initrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd' Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' Marvell>> setenv usb_boot 'usb start; run load_uimage; run load_initrd; bootm 0x800000 0x2100000' Marvell>> setenv bootcmd 'run usb_make_boot_args ; run usb_boot; run flash_load; reset' Marvell>> boot (Re)start USB... USB: scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found .... . ...... ............ ......................... ................................................... ...................................................................................................... ............................................................................................................................................................................................................ .... .............................................................................................. 5212194 bytes read .... . ...... ............ ......................... ................................................... ...................................................................................................... ............................................................................................................................................................................................................ .... .................................................................................................................................................................................................................................................................................................................................................................................................................... .... ........................................................................................................................ 9672526 bytes read ## Booting image at 00800000 ... Image Name: Linux-5.5.1-kirkwood-tld-1 Created: 2020-02-07 23:07:53 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5212130 Bytes = 5 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 02100000 ... Image Name: initramfs-5.5.1-kirkwood-tld-1 Created: 2020-02-10 0:20:06 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9672462 Bytes = 9.2 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.5.1-kirkwood-tld-1 (root@tldDebian) (gcc version 8.3.0 (Debian 8.3.0-6)) #1.0 PREEMPT Sat Feb 1 22:28:36 PST 2020 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Iomega ix4-200d [ 0.000000][ T0] printk: bootconsole [earlycon0] enabled [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 earlyprintk=serial mtdparts=orion_nand:0xa0000@0x0(uboot),0x10000@0xa0000(env),0x224000@0xb0000(zImage),0x224000@0x2d4000(initrd),32m@0x0(flash) root=LABEL=rootfs rootdelay=10 [ 0.000000][ T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 493660K/524288K available (9216K kernel code, 926K rwdata, 3860K rodata, 1024K init, 296K bss, 30628K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from ____cache_alloc+0x470/0x80c with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000008][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008513][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.015821][ T0] Console: colour dummy device 80x30 [ 0.021012][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.032226][ T0] pid_max: default: 32768 minimum: 301 [ 0.037879][ T0] LSM: Security Framework initializing [ 0.043373][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.051398][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.059977][ T0] *** VALIDATE tmpfs *** [ 0.064873][ T0] *** VALIDATE proc *** [ 0.069142][ T0] *** VALIDATE cgroup1 *** [ 0.073407][ T0] *** VALIDATE cgroup2 *** [ 0.077739][ T0] CPU: Testing write buffer coherency: ok [ 0.085052][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.092229][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.098284][ T1] rcu: Hierarchical SRCU implementation. [ 0.106350][ T1] devtmpfs: initialized [ 0.115798][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.126372][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.134156][ T1] xor: measuring software checksum speed [ 0.238542][ T1] arm4regs : 1083.200 MB/sec [ 0.338543][ T1] 8regs : 650.400 MB/sec [ 0.438543][ T1] 32regs : 945.600 MB/sec [ 0.443402][ T1] xor: using function: arm4regs (1083.200 MB/sec) [ 0.449683][ T1] prandom: seed boundary self test passed [ 0.459459][ T1] prandom: 100 self tests passed [ 0.464233][ T1] pinctrl core: initialized pinctrl subsystem [ 0.471053][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.471687][ T1] NET: Registered protocol family 16 [ 0.484248][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.492772][ T1] audit: initializing netlink subsys (disabled) [ 0.500191][ T14] audit: type=2000 audit(0.490:1): state=initialized audit_enabled=0 res=1 [ 0.508742][ T1] cpuidle: using governor ladder [ 0.513585][ T1] cpuidle: using governor menu [ 0.518787][ T1] Feroceon L2: Enabling L2 [ 0.523072][ T1] Feroceon L2: Cache support initialised. [ 0.534881][ T1] No ATAGs? [ 2.568523][ C0] random: fast init done [ 5.639023][ T1] raid6: int32x8 gen() 105 MB/s [ 5.808764][ T1] raid6: int32x8 xor() 65 MB/s [ 5.978976][ T1] raid6: int32x4 gen() 106 MB/s [ 6.148786][ T1] raid6: int32x4 xor() 68 MB/s [ 6.318739][ T1] raid6: int32x2 gen() 131 MB/s [ 6.488587][ T1] raid6: int32x2 xor() 93 MB/s [ 6.659090][ T1] raid6: int32x1 gen() 100 MB/s [ 6.828829][ T1] raid6: int32x1 xor() 68 MB/s [ 6.833768][ T1] raid6: using algorithm int32x2 gen() 131 MB/s [ 6.839852][ T1] raid6: .... xor() 93 MB/s, rmw enabled [ 6.845311][ T1] raid6: using intx1 recovery algorithm [ 6.850948][ T1] vgaarb: loaded [ 6.854923][ T1] SCSI subsystem initialized [ 6.859883][ T1] usbcore: registered new interface driver usbfs [ 6.866107][ T1] usbcore: registered new interface driver hub [ 6.872214][ T1] usbcore: registered new device driver usb [ 6.878133][ T1] pps_core: LinuxPPS API ver. 1 registered [ 6.883793][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 6.893614][ T1] PTP clock support registered [ 6.899712][ T1] clocksource: Switched to clocksource orion_clocksource [ 8.252101][ T1] *** VALIDATE bpf *** [ 8.256443][ T1] VFS: Disk quotas dquot_6.6.0 [ 8.261158][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 8.268870][ T1] *** VALIDATE ramfs *** [ 8.283677][ T1] NET: Registered protocol family 2 [ 8.289562][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 8.298684][ T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 8.307193][ T1] TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 8.315076][ T1] TCP: Hash tables configured (established 4096 bind 4096) [ 8.322260][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 8.329467][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 8.337333][ T1] NET: Registered protocol family 1 [ 8.343115][ T1] RPC: Registered named UNIX socket transport module. [ 8.349700][ T1] RPC: Registered udp transport module. [ 8.355155][ T1] RPC: Registered tcp transport module. [ 8.360551][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 8.367659][ T1] PCI: CLS 0 bytes, default 32 [ 8.372587][ T1] Trying to unpack rootfs image as initramfs... [ 9.251144][ T1] Freeing initrd memory: 9448K [ 9.255934][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 9.264495][ T1] Initialise system trusted keyrings [ 9.269648][ T1] Key type blacklist registered [ 9.274626][ T1] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 9.281904][ T1] zbud: loaded [ 9.286329][ T1] NFS: Registering the id_resolver key type [ 9.292154][ T1] Key type id_resolver registered [ 9.297007][ T1] Key type id_legacy registered [ 9.301732][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 9.309102][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 9.316565][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 9.324764][ T1] *** VALIDATE jffs2 *** [ 9.328850][ T1] fuse: init (API version 7.31) [ 9.333572][ T1] *** VALIDATE fuse *** [ 9.337567][ T1] *** VALIDATE fuse *** [ 9.341934][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 9.349228][ T1] orangefs_init: module version upstream loaded [ 9.355328][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 9.365162][ T1] *** VALIDATE xfs *** [ 9.420215][ T1] async_tx: api initialized (async) [ 9.425259][ T1] Key type asymmetric registered [ 9.430126][ T1] Asymmetric key parser 'x509' registered [ 9.435731][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 9.445382][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 9.454870][ T1] mvebu-gpio f1010140.gpio: IRQ index 3 not found [ 9.461788][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 9.470093][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 9.476250][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 9.483811][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 9.490847][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 9.497542][ T1] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref] [ 9.505951][ T1] PCI: bus0: Fast back to back transfers disabled [ 9.512237][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 9.521116][ T1] pci 0000:01:00.0: [11ab:6121] type 00 class 0x01018f [ 9.527811][ T1] pci 0000:01:00.0: reg 0x10: [io 0x0000-0x0007] [ 9.534089][ T1] pci 0000:01:00.0: reg 0x14: [io 0xf0000008-0xf000000b] [ 9.541053][ T1] pci 0000:01:00.0: reg 0x18: [io 0x0000-0x0007] [ 9.547303][ T1] pci 0000:01:00.0: reg 0x1c: [io 0xf0000018-0xf000001b] [ 9.554263][ T1] pci 0000:01:00.0: reg 0x20: [io 0xf0000020-0xf000002f] [ 9.561226][ T1] pci 0000:01:00.0: reg 0x24: [mem 0x40000000-0x400003ff] [ 9.568236][ T1] pci 0000:01:00.0: supports D1 [ 9.572945][ T1] pci 0000:01:00.0: PME# supported from D0 D1 D3hot [ 9.579622][ T1] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 9.591076][ T1] PCI: bus1: Fast back to back transfers disabled [ 9.597331][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 9.604820][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff] [ 9.612389][ T1] pci 0000:00:01.0: BAR 13: assigned [io 0x10000-0x10fff] [ 9.619407][ T1] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0100000-0xe01007ff pref] [ 9.627327][ T1] pci 0000:01:00.0: BAR 5: assigned [mem 0xe0000000-0xe00003ff] [ 9.634804][ T1] pci 0000:01:00.0: BAR 4: assigned [io 0x10000-0x1000f] [ 9.641766][ T1] pci 0000:01:00.0: BAR 0: assigned [io 0x10010-0x10017] [ 9.648707][ T1] pci 0000:01:00.0: BAR 2: assigned [io 0x10018-0x1001f] [ 9.655668][ T1] pci 0000:01:00.0: BAR 1: assigned [io 0x10020-0x10023] [ 9.662631][ T1] pci 0000:01:00.0: BAR 3: assigned [io 0x10024-0x10027] [ 9.669564][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 9.675225][ T1] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff] [ 9.682182][ T1] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 9.689749][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0143) [ 9.697023][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 9.760760][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 9.771301][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 9.840712][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 9.851512][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 9.859903][ T1] printk: console [ttyS0] disabled [ 9.864925][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 9.874638][ T1] printk: console [ttyS0] enabled [ 9.874638][ T1] printk: console [ttyS0] enabled [ 9.884481][ T1] printk: bootconsole [earlycon0] disabled [ 9.884481][ T1] printk: bootconsole [earlycon0] disabled [ 9.904269][ T1] loop: module loaded [ 9.908720][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 9.918008][ T1] scsi host0: sata_mv [ 9.922495][ T1] scsi host1: sata_mv [ 9.926628][ T1] ata1: SATA max UDMA/133 irq 33 [ 9.931510][ T1] ata2: SATA max UDMA/133 irq 33 [ 9.937289][ T1] nand: device found, Manufacturer ID: 0xec, Chip ID: 0x75 [ 9.944497][ T1] nand: Samsung NAND 32MiB 3,3V 8-bit [ 9.949779][ T1] nand: 32 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16 [ 9.957837][ T1] Scanning device for bad blocks [ 10.300918][ T1] 5 cmdlinepart partitions found on MTD device orion_nand [ 10.307915][ T1] Creating 5 MTD partitions on "orion_nand": [ 10.313804][ T1] 0x000000000000-0x0000000a0000 : "uboot" [ 10.320916][ T1] 0x0000000a0000-0x0000000b0000 : "env" [ 10.327716][ T1] 0x0000000b0000-0x0000002d4000 : "zImage" [ 10.334894][ T1] 0x0000002d4000-0x0000004f8000 : "initrd" [ 10.342038][ T1] 0x000000000000-0x000002000000 : "flash" [ 10.351382][ T1] libphy: Fixed MDIO Bus: probed [ 10.357027][ T1] libphy: orion_mdio_bus: probed [ 10.391144][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 10.439759][ T118] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 10.869793][ T118] ata1.00: ATA-8: TOSHIBA MK7559GSXP, GN001A, max UDMA/100 [ 10.876882][ T118] ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 10.889177][ T118] ata1.00: configured for UDMA/100 [ 10.904723][ T7] scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK7559GS 1A PQ: 0 ANSI: 5 [ 10.914838][ T122] sd 0:0:0:0: [sda] 1465149168 512-byte logical blocks: (750 GB/699 GiB) [ 10.923646][ T122] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 10.929780][ T122] sd 0:0:0:0: [sda] Write Protect is off [ 10.935436][ T122] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 11.120423][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:50:43:70:23:36 [ 11.409267][ T122] sda: sda1 sda2 [ 11.414682][ T122] sd 0:0:0:0: [sda] Attached SCSI disk [ 11.420104][ T120] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl F300) [ 11.449851][ T120] ata2.00: ATA-7: SAMSUNG HM120JI, YF100-18, max UDMA/100 [ 11.456849][ T120] ata2.00: 234441648 sectors, multi 0: LBA48 [ 11.489853][ T120] ata2.00: configured for UDMA/100 [ 11.505345][ T22] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HM120JI 0-18 PQ: 0 ANSI: 5 [ 11.515443][ T122] sd 1:0:0:0: [sdb] 234441648 512-byte logical blocks: (120 GB/112 GiB) [ 11.524065][ T122] sd 1:0:0:0: [sdb] Write Protect is off [ 11.529752][ T122] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 11.850436][ T1] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:50:43:70:23:37 [ 11.860072][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 11.867352][ T1] ehci-pci: EHCI PCI platform driver [ 11.872609][ T1] ehci-orion: EHCI orion driver [ 11.877544][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 11.883824][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 11.892446][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 11.919754][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 11.926771][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.05 [ 11.935807][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 11.943786][ T1] usb usb1: Product: EHCI Host Controller [ 11.949388][ T1] usb usb1: Manufacturer: Linux 5.5.1-kirkwood-tld-1 ehci_hcd [ 11.956751][ T1] usb usb1: SerialNumber: f1050000.ehci [ 11.962875][ T1] hub 1-0:1.0: USB hub found [ 11.967394][ T1] hub 1-0:1.0: 1 port detected [ 11.972866][ T1] usbcore: registered new interface driver usb-storage [ 11.980053][ T1] mousedev: PS/2 mouse device common for all mice [ 11.987123][ T1] rtc-mv f1010300.rtc: registered as rtc0 [ 11.992940][ T1] i2c /dev entries driver [ 11.998513][ T1] device-mapper: uevent: version 1.0.3 [ 12.004244][ T1] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com [ 12.014233][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 12.021574][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 12.028987][ T122] sdb: sdb1 sdb2 sdb3 < sdb5 > [ 12.033770][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 12.043314][ T122] sd 1:0:0:0: [sdb] Attached SCSI disk [ 12.048769][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 12.055664][ T1] device-mapper: raid: Loading target version 1.15.0 [ 12.063221][ T1] hid: raw HID events driver (C) Jiri Kosina [ 12.069410][ T1] exFAT: Version 1.3.0 [ 12.073518][ T1] drop_monitor: Initializing network drop monitor service [ 12.080947][ T1] NET: Registered protocol family 17 [ 12.086382][ T1] Key type dns_resolver registered [ 12.092032][ T1] registered taskstats version 1 [ 12.096849][ T1] Loading compiled-in X.509 certificates [ 12.102500][ T1] zswap: loaded using pool lzo/zbud [ 12.107775][ T1] Key type ._fscrypt registered [ 12.112534][ T1] Key type .fscrypt registered [ 12.219232][ T1] Key type big_key registered [ 12.267851][ T1] Key type encrypted registered [ 12.275329][ T1] rtc-mv f1010300.rtc: setting system clock to 2020-02-12T22:09:29 UTC (1581545369) [ 12.288042][ T1] Freeing unused kernel memory: 1024K [ 12.310509][ T1] Checked W+X mappings: passed, no W+X pages found [ 12.316899][ T1] Run /init as init process [ 12.339843][ T130] usb 1-1: new high-speed USB device number 2 using orion-ehci Loading, please wait... [ 12.391972][ T130] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice= 9.01 [ 12.405261][ T130] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 12.420145][ T130] usb 1-1: Product: USB2.0 Hub [ 12.430555][ T130] hub 1-1:1.0: USB hub found [ 12.435921][ T130] hub 1-1:1.0: 4 ports detected Starting version 241 [ 12.759809][ T130] usb 1-1.1: new high-speed USB device number 3 using orion-ehci [ 12.822731][ T130] usb 1-1.1: New USB device found, idVendor=8564, idProduct=1000, bcdDevice=11.00 [ 12.849790][ T130] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 12.857855][ T130] usb 1-1.1: Product: Mass Storage Device [ 12.888074][ T130] usb 1-1.1: Manufacturer: JetFlash [ 12.901669][ T130] usb 1-1.1: SerialNumber: 26X4R0R0EBEQBAA5 [ 12.923828][ T130] usb-storage 1-1.1:1.0: USB Mass Storage device detected [ 12.952486][ T130] scsi host2: usb-storage 1-1.1:1.0 [ 13.226100][ T172] usbcore: registered new interface driver uas [ 13.388903][ T172] ahci 0000:01:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this. [ 13.448633][ T172] ahci 0000:01:00.0: controller can't do NCQ, turning off CAP_NCQ [ 13.488275][ T172] ahci 0000:01:00.0: controller can't do PMP, turning off CAP_PMP [ 13.535924][ T172] ahci 0000:01:00.0: masking port_map 0x7 -> 0x3 [ 13.558879][ T172] ahci 0000:01:00.0: SSS flag set, parallel bus scan disabled [ 13.600645][ T172] ahci 0000:01:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode [ 13.651986][ T172] ahci 0000:01:00.0: flags: 64bit stag led slum part [ 13.711114][ T172] scsi host3: ahci [ 13.728913][ T172] scsi host4: ahci [ 13.753070][ T172] scsi host5: ahci [ 13.757053][ T172] ata3: SATA max UDMA/133 abar m1024@0xe0000000 port 0xe0000100 irq 38 [ 13.803069][ T172] ata4: SATA max UDMA/133 abar m1024@0xe0000000 port 0xe0000180 irq 38 [ 13.837462][ T172] ata5: DUMMY [ 14.181535][ T184] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 14.189042][ T184] ata3.00: ATA-7: WDC WD2500KS-00MJB0, 02.01C03, max UDMA/133 [ 14.196426][ T184] ata3.00: 488397168 sectors, multi 0: LBA48 [ 14.203069][ T184] ata3.00: configured for UDMA/133 [ 14.218191][ T122] scsi: waiting for bus probes to complete ... [ 14.333438][ T123] scsi 2:0:0:0: Direct-Access JetFlash Transcend 32GB 1100 PQ: 0 ANSI: 4 [ 14.347754][ T122] scsi 3:0:0:0: Direct-Access ATA WDC WD2500KS-00M 1C03 PQ: 0 ANSI: 5 [ 14.357767][ T123] sd 2:0:0:0: [sdc] 63406080 512-byte logical blocks: (32.5 GB/30.2 GiB) [ 14.373043][ T192] sd 3:0:0:0: [sdd] 488397168 512-byte logical blocks: (250 GB/233 GiB) [ 14.384134][ T192] sd 3:0:0:0: [sdd] Write Protect is off [ 14.390015][ T123] sd 2:0:0:0: [sdc] Write Protect is off [ 14.395607][ T192] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 14.405740][ T123] sd 2:0:0:0: [sdc] No Caching mode page found [ 14.414893][ T123] sd 2:0:0:0: [sdc] Assuming drive cache: write through [ 14.427647][ T192] sdd: sdd1 [ 14.431116][ T123] sdc: sdc1 [ 14.437101][ T192] sd 3:0:0:0: [sdd] Attached SCSI disk [ 14.452887][ T123] sd 2:0:0:0: [sdc] Attached SCSI removable disk [ 14.711585][ T186] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 14.719702][ T186] ata4.00: ATA-8: Hitachi HUA723020ALA641, MK7OA840, max UDMA/133 [ 14.727434][ T186] ata4.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 14.736143][ T186] ata4.00: configured for UDMA/133 [ 14.751700][ T22] scsi 4:0:0:0: Direct-Access ATA Hitachi HUA72302 A840 PQ: 0 ANSI: 5 [ 14.762961][ T123] sd 4:0:0:0: [sde] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB) [ 14.773521][ T123] sd 4:0:0:0: [sde] Write Protect is off [ 14.779670][ T123] sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 14.824099][ T123] sde: sde1 sde2 [ 14.831382][ T123] sd 4:0:0:0: [sde] Attached SCSI disk [ 16.974619][ C0] random: crng init done Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.33.1 [/sbin/fsck.ext3 (1) -- /dev/sdc1] fsck.ext3 -a -C0 /dev/sdc1 rootfs: clean, 225131/1982464 files, 1584906/7925504 blocks done. [ 28.557519][ T215] EXT4-fs (sdc1): mounting ext3 file system using the ext4 subsystem [ 28.605150][ T215] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null) done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.93 booting [[36minfo[39;49m] Using makefile-style concurrent boot in runlevel S. [....] Starting hotplug events dispatcher: systemd-udevd[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Synthesizing the initial hotplug events (subsystems)...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Synthesizing the initial hotplug events (devices)...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Waiting for /dev to be fully populated...[ 31.744117][ T430] systemd-udevd[430]: Using default interface naming scheme 'v240'. [ 31.752559][ T431] systemd-udevd[431]: Using default interface naming scheme 'v240'. [ 31.836848][ T430] systemd-udevd[430]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 31.849207][ T431] systemd-udevd[431]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 31.919895][ T432] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 31.972659][ T432] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 31.995202][ T399] adt7475 0-002e: ADT7473 device, revision 0 [ 32.033917][ T432] sd 2:0:0:0: Attached scsi generic sg2 type 0 [ 32.086924][ T399] adt7475 0-002e: Optional features: fan4 pwm2 [ 32.124871][ T432] sd 3:0:0:0: Attached scsi generic sg3 type 0 [ 32.153622][ T400] watchdog: f1020300.watchdog-timer: driver supplied timeout (4294967295) out of range [ 32.254262][ T432] sd 4:0:0:0: Attached scsi generic sg4 type 0 [ 32.359824][ T400] watchdog: f1020300.watchdog-timer: falling back to default timeout (21) [ 32.484026][ T400] orion_wdt: Initial timeout 21 sec [ 32.907487][ T402] marvell-cesa f1030000.crypto: CESA device successfully registered [ 33.199901][ T399] systemd-udevd[399]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 63.591404][ T186] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 63.600771][ T186] ata4.00: configured for UDMA/133 [?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Setting hostname to 'debian'...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Activating swap:[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [ 65.861267][ T680] EXT4-fs (sdc1): re-mounted. Opts: errors=remount-ro [[36minfo[39;49m] Will now check all file systems. fsck from util-linux 2.33.1 Checking all file systems. LABEL=rootfs is mounted [....] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Cleaning up temporary files...[....] Cleaning /tmp...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. /tmp[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Will now mount local filesystems:[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Will now activate swapfile swap:[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Checking minimum space in /tmp...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Cleaning up temporary files...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting Setting kernel variables: sysctl[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Initializing random number generator...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/00:50:43:70:23:36 Sending on LPF/eth0/00:50:43:70:23:36 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6 [ 72.416262][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 DHCPOFFER of 192.168.1.191 from 192.168.1.1 DHCPREQUEST for 192.168.1.191 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.1.191 from 192.168.1.1 bound to 192.168.1.191 -- renewal in 2783 seconds. [ 78.374048][ T1233] NET: Registered protocol family 10 [ 78.380978][ T1233] Segment Routing with IPv6 [?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Starting RPC port mapper daemon: rpcbind[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting NFS common utilities: statd idmapd[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Cleaning up temporary files...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. INIT: Entering runlevel: 2 [[36minfo[39;49m] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1451 (syslogd) [?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1478 (klogd) [?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting system message bus: dbus[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting NFS common utilities: statd idmapd[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Not starting NFS kernel daemon: no exports. ...[?25l[?1c7[1G[[33mwarn[39;49m8[?25h[?0c [33m(warning).[39;49m [....] Starting NTP server: ntpd[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Starting OpenBSD Secure Shell server: sshd[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Running local boot scripts (/etc/rc.local)[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. Debian GNU/Linux 10 debian ttyS0
[ 78.380978] Segment Routing with IPv6 [ 199.271245] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 199.281274] ata4.00: configured for UDMA/133 [ 331.121148] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 331.131194] ata4.00: configured for UDMA/133 [ 371.749278] ata4: limiting SATA link speed to 1.5 Gbps [ 372.080874] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 377.138975] ata4.00: qc timeout (cmd 0xec) [ 377.143809] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 377.150992] ata4.00: revalidation failed (errno=-5) [ 377.480610] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 387.698519] ata4.00: qc timeout (cmd 0xec) [ 387.703355] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 387.710552] ata4.00: revalidation failed (errno=-5) [ 388.040144] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 418.417901] ata4.00: qc timeout (cmd 0xec) [ 418.422737] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 418.429956] ata4.00: revalidation failed (errno=-5) [ 418.435596] ata4.00: disabled [ 418.769524] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
Re: Help with iomega ix4-200d installation February 13, 2020 01:12AM |
Admin Registered: 13 years ago Posts: 18,898 |
Re: Help with iomega ix4-200d installation February 22, 2020 11:51AM |
Registered: 5 years ago Posts: 258 |
00011111111111111111111111111111111111111111111111111111111111100000111111111111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111111111111000000011111111111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111111111111000000011111111111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111111111111000000011111111111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111111111111000000011111111111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111111111111000000011111111111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111111111111100000111111111111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111110000000000000000000001111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111110000000000000000000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000111111111100000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000111111111100000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000111111111110000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000111111111110000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000111111111110000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000000111111110000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000000011111100000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111100000000000000000000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111110000000000000000000000111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111110000000000000000000001111111111111111111111111111111111111111111111111111 00011111111111111111111111111111100011111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111 00011111111111111111111111111111100011111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111 00011111111111111111111111111111100011111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111 00011111111111111111111111111111000011110000000111000100000110000011110000001111000000000110000001111111111111111111111111111111 00011111111111111111111111111111100011100011100011000000000000000011100011000110001100011101110000111111111111111111111111111111 00011111111111111111111111111111100011000011100011000011000011100001000111000110001110001111111000111111111111111111111111111111 00011111111111111111111111111111100011000111100001000111100011100001000111000100001110001111111000111111111111111111111111111111 00011111111111111111111111111111100011000111100001000111100011100001000100000110001100011111100000111111111111111111111111111111 00011111111111111111111111111111100011000111100001000111100011100001000111111110001100011100011000111111111111111111111111111111 00011111111111111111111111111111100011000111100001000111100011100001000111111111000000111000111000111111111111111111111111111111 00011111111111111111111111111111100011000111100001000111100011100001000011111111001111111000111000111111111111111111111111111111 00011111111111111111111111111111100011000011100011000111100011100001100011111110001111111000111000111111111111111111111111111111 00011111111111111111111111111111100011100011000111000111100011100001100000000110000000011000010000111111111111111111111111111111 00011111111111111111111111111111100011111000001111000111100011100001111000011111000000000100001100011111111111111111111111111111 00011111111111111111111111111111111111111111111111111111111111111111111111111110111110000111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111111111111111111111111111100011111000111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111111111111111111111111111100011111000111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111111111111111111111111111100011111001111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111111111111111111111111111110011110011111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111111111111111111111111111111000001111111111111111111111111111111111111111111 00011111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111
Re: Help with iomega ix4-200d installation February 22, 2020 06:09PM |
Admin Registered: 13 years ago Posts: 18,898 |
> 00011111111111111111111111111111111111111111111111111111111111100000111111111111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111111111111000000011111111111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111111111111000000011111111111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111111111111000000011111111111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111111111111000000011111111111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111111111111000000011111111111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111111111111100000111111111111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111110000000000000000000001111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111110000000000000000000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000111111111100000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000111111111100000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000111111111110000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000111111111110000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000111111111110000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000000111111110000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000000011111110000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000000011111100000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111100000000000000000000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111110000000000000000000000111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111110000000000000000000001111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111100011111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111100011111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111100011111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111 > 00011111111111111111111111111111000011110000000111000100000110000011110000001111000000000110000001111111111111111111111111111111 > 00011111111111111111111111111111100011100011100011000000000000000011100011000110001100011101110000111111111111111111111111111111 > 00011111111111111111111111111111100011000011100011000011000011100001000111000110001110001111111000111111111111111111111111111111 > 00011111111111111111111111111111100011000111100001000111100011100001000111000100001110001111111000111111111111111111111111111111 > 00011111111111111111111111111111100011000111100001000111100011100001000100000110001100011111100000111111111111111111111111111111 > 00011111111111111111111111111111100011000111100001000111100011100001000111111110001100011100011000111111111111111111111111111111 > 00011111111111111111111111111111100011000111100001000111100011100001000111111111000000111000111000111111111111111111111111111111 > 00011111111111111111111111111111100011000111100001000111100011100001000011111111001111111000111000111111111111111111111111111111 > 00011111111111111111111111111111100011000011100011000111100011100001100011111110001111111000111000111111111111111111111111111111 > 00011111111111111111111111111111100011100011000111000111100011100001100000000110000000011000010000111111111111111111111111111111 > 00011111111111111111111111111111100011111000001111000111100011100001111000011111000000000100001100011111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111111111111111111111111111110111110000111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111111111111111111111111111100011111000111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111111111111111111111111111100011111000111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111111111111111111111111111100011111001111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111111111111111111111111111110011110011111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111111111111111111111111111111000001111111111111111111111111111111111111111111 > 00011111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111111 > >
Re: Help with iomega ix4-200d installation February 22, 2020 06:26PM |
Registered: 5 years ago Posts: 258 |
Mr. Poopybutthole
Re: Help with iomega ix4-200d installation June 11, 2020 04:44AM |
[ 2041.190866][ T176] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2046.249406][ T176] ata3.00: qc timeout (cmd 0xec) [ 2046.254242][ T176] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 2046.266561][ T176] ata3.00: revalidation failed (errno=-5) [ 2046.610898][ T176] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2046.658862][ T176] ata3.00: configured for UDMA/133 [ 3874.140902][ T176] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 3879.209402][ T176] ata3.00: qc timeout (cmd 0xec) [ 3879.214234][ T176] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 3879.226518][ T176] ata3.00: revalidation failed (errno=-5) [ 3879.570899][ T176] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 3889.769373][ T176] ata3.00: qc timeout (cmd 0xec) [ 3889.774206][ T176] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 3889.786405][ T176] ata3.00: revalidation failed (errno=-5) [ 3889.804762][ T176] ata3: limiting SATA link speed to 1.5 Gbps [ 3890.150867][ T176] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 3920.489373][ T176] ata3.00: qc timeout (cmd 0xec) [ 3920.494209][ T176] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 3920.513218][ T176] ata3.00: revalidation failed (errno=-5) [ 3920.518879][ T176] ata3.00: disabled [ 3920.850878][ T176] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 3920.858156][ C0] sd 3:0:0:0: [sda] tag#17 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK [ 3920.868958][ C0] sd 3:0:0:0: [sda] tag#17 CDB: Synchronize Cache(10) 35 00 00 00 00 00 00 00 00 00 [ 3920.879621][ C0] print_req_error: I/O error, dev sda, sector 15706128 flags 801 [ 3920.975353][ C0] sd 3:0:0:0: [sda] tag#14 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK [ 3920.984936][ C0] sd 3:0:0:0: [sda] tag#14 CDB: Read(10) 28 00 19 34 8b 80 00 06 80 00 [ 3920.993111][ C0] print_req_error: I/O error, dev sda, sector 422873984 flags 4000 [ 3921.086637][ C0] sd 3:0:0:0: [sda] tag#15 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK [ 3921.096235][ C0] sd 3:0:0:0: [sda] tag#15 CDB: Read(10) 28 00 19 34 92 00 00 05 00 00 [ 3921.104403][ C0] print_req_error: I/O error, dev sda, sector 422875648 flags 4000 [ 3921.135252][ C0] sd 3:0:0:0: [sda] tag#16 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK [ 3921.144832][ C0] sd 3:0:0:0: [sda] tag#16 CDB: Read(10) 28 00 19 34 97 00 00 04 00 00 [ 3921.153000][ C0] print_req_error: I/O error, dev sda, sector 422876928 flags 0 [ 3921.166275][ C0] sd 3:0:0:0: [sda] tag#18 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK [ 3921.175894][ C0] sd 3:0:0:0: [sda] tag#18 CDB: ATA command pass through(16) 85 06 2c 00 da 00 00 00 00 00 4f 00 c2 00 b0 00 [ 3921.239750][ C0] sd 3:0:0:0: [sda] tag#22 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK [ 3921.250468][ C0] sd 3:0:0:0: [sda] tag#22 CDB: Read(10) 28 00 19 34 8b 80 00 00 08 00 [ 3921.260008][ C0] print_req_error: I/O error, dev sda, sector 422873984 flags 800 [ 3921.286817][ C0] sd 3:0:0:0: [sda] tag#23 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK [ 3921.296425][ C0] sd 3:0:0:0: [sda] tag#23 CDB: Write(10) 2a 00 19 34 8b 80 00 00 08 00 [ 3921.304704][ C0] print_req_error: I/O error, dev sda, sector 422873984 flags 801 [ 3921.353633][ C0] sd 3:0:0:0: [sda] tag#24 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK [ 3921.363247][ C0] sd 3:0:0:0: [sda] tag#24 CDB: Read(10) 28 00 19 34 8c 00 00 00 08 00 [ 3921.371419][ C0] print_req_error: I/O error, dev sda, sector 422874112 flags 800 [ 3921.420665][ C0] sd 3:0:0:0: [sda] tag#25 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK [ 3921.430257][ C0] sd 3:0:0:0: [sda] tag#25 CDB: Write(10) 2a 00 19 34 8c 00 00 00 08 00 [ 3921.438481][ C0] print_req_error: I/O error, dev sda, sector 422874112 flags 801 [ 3921.553459][ C0] sd 3:0:0:0: [sda] tag#26 FAILED Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK [ 3921.563035][ C0] sd 3:0:0:0: [sda] tag#26 CDB: Read(10) 28 00 19 34 8c 80 00 00 08 00 [ 3921.571199][ C0] print_req_error: I/O error, dev sda, sector 422874240 flags 800 [ 3921.595265][ C0] print_req_error: I/O error, dev sda, sector 422874240 flags 801
Model Family: Hitachi Deskstar 7K3000 Device Model: Hitachi HDS723020BLA642 LU WWN Device Id: 5 000cca 369d47013 Firmware Version: MN6OA5C0 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches