Re: ix2-200 boots USB but not HDD February 24, 2020 10:41AM |
Registered: 4 years ago Posts: 23 |
root@debian:~# nandwrite -p /dev/mtd2 /mnt/uImage-bodhi Image 4975416 bytes, NAND page 512 bytes, OOB area 16 bytes, device size 3145728 bytes nandwrite: error!: Input file does not fit into device error 0 (Success) nandwrite: error!: Data was only partially written due to error error 0 (Success)
Marvell>> bootm 0x00800000 0x01100000 ## Booting image at 00800000 ... Image Name: Linux-5.2.9-kirkwood-tld-1 Created: 2020-02-14 20:02:37 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4975352 Bytes = 4.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 01100000 ... Image Name: initrd.img-5.2.9-kirkwood-tld-1 Created: 2020-02-24 15:34:56 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9713872 Bytes = 9.3 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel.
Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x300000 3145728 bytes read: OK NAND read: device 0 offset 0x1000000, size 0x1000000 16777216 bytes read: ERROR ## Booting image at 00800000 ... Image Name: Linux-3.16.0-6 Created: 2020-02-06 12:34:50 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2076864 Bytes = 2 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 02100000 ... Bad Magic Number
Re: ix2-200 boots USB but not HDD February 24, 2020 07:52PM |
Admin Registered: 13 years ago Posts: 18,495 |
Quote
I reloaded my original HDDs with jessie rootfs and booted from the USB stick to try nandwrite with your uImage & uInitrd but it fails
root@debian:~# nandwrite -p /dev/mtd2 /mnt/uImage-bodhi
Image 4975416 bytes, NAND page 512 bytes, OOB area 16 bytes, device size 3145728 bytes
nandwrite: error!: Input file does not fit into device
error 0 (Success)
nandwrite: error!: Data was only partially written due to error
error 0 (Success)
Quote
I also tried copy your uImage & uInitrd to my USB stick and try booting with them but it stalls out booting the kernel
Quote
Updated 25 Aug 2019:
Basic Debian buster Kirkwood rootfs for most Kirwood plugs:
- tarball size: 209M
- install size: 536M
- The init system used in this rootfs is sysvinit . To boot with systemd, see note 2 below.
- Installed packages: nano, avahi, ntp, busybox-syslogd (log to RAM), htop, isc-dhcp-client, dialog, bzip2, nfs server/client, iperf, ethtool, sysvinit-core, sysvinit, sysvinit-utils, u-boot-tools, and mtd-utils.
- see LED controls in /etc/rc.local, and /etc/init.d/halt
- see some useful aliases in /root/.profile
- root password: root
Download at Dropbox:
Debian-5.2.9-kirkwood-tld-1-rootfs-bodhi.tar.bz2
md5:
cd8ad170aa1a9fdc2a0a1c43ab1c0721
sha256:
8ccbbced367b4c2bf3728262e882f8232aff0fecd1c0c767219a0cab49a0b9bf
And remember to check the hash of what you download, as always.
Installation:
Installation can be done on any Linux box, with a fresh USB drive (SD card or HDD would work fine too).
Note: all steps below must be done while logging in as root user (not sudo). If you are not the root user then don't continue, because the rootfs will not work.
1. Format a new USB drive with a single Ext3 partition, and label it rootfs. If you are running the latest U-Boot for Kirkwood then you can use Ext4.
2. Mount the drive on a Linux box. cd to top level directory and extract it. It is assuming the USB drive is mounted at /media/sdb1
cd /media/sdb1
tar -xjf Debian-5.2.9-kirkwood-tld-1-rootfs-bodhi.tar.bz2
3. Adjust fstab (optional).
Edit /media/sdb1/etc/fstab entry for root device to match the rootfstype of your rootfstype if you use Ext4 or Ext2. However, you can keep it as is without problem in booting since the kernel will figure out which file system the rootfs was formatted.
LABEL=rootfs / ext3 noatime,errors=remount-ro 0 1
4. Create uImage with embedded DTB for booting with older u-boots (2012 or earlier). Do not do this step if you have installed the latest U-Boot for Kirkwood (or are installing this u-boot at the same time).
Please replace kirkwood-goflexnet.dtb below with the correct DTB name for your box (see the folder /media/sdb1/boot/dts for the exact spelling of your Kirkwood box name).
Generate the uImage with DTB embedded inside:
cd /media/sdb1/boot
cp -a zImage-5.2.9-kirkwood-tld-1 zImage.fdt
cat dts/kirkwood-goflexnet.dtb >> zImage.fdt
mv uImage uImage.orig
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-5.2.9-kirkwood-tld-1 -d zImage.fdt uImage
sync
If your Linux box does not have mkimage, then install it
apt-get install u-boot-tools
5. Done. Take this USB rootfs to your plug and cold start. After booted into Debian, see Note1 and Note2 below. It is very important that you do Note1 steps to secure your box.
printenv
Re: ix2-200 boots USB but not HDD February 25, 2020 09:00AM |
Registered: 4 years ago Posts: 23 |
Marvell>> printenv baudrate=115200 loads_echo=0 ipaddr=10.4.50.165 serverip=10.4.50.5 rootpath=/mnt/ARM_FS/ netmask=255.255.255.0 console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x1f00000@0x100000(root) CASset=min MALLOC_len=1 ethprime=egiga1 bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; ethmtu=1500 eth1addr=00:50:43:a0:0a:27 eth1mtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 nandEcc=1bit netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no FanHysteresis=2 FanTempStart=58 uboot_start=0x0 uboot_size=0xc0000 env_start=0xa0000 env_size=0x20000 kernel_start=0x100000 kernel_size=0x300000 initrd_start=0x540000 initrd_size=0x300000 flash_load=run make_boot_args load1 load2 boot load1=nand read.e 0x2000000 $(kernel_start) $(kernel_size) load2=nand read.e 0x4500000 $(initrd_start) $(initrd_size) boot=bootm 0x2000000 0x4500000 make_boot_args=setenv bootargs console=ttyS0,115200 mtdparts=nand_mtd:;setenv bootargs $(bootargs)$(uboot_size)@$(uboot_start)(uboot),;setenv bootargs $(bootargs)$(env_size)@$(env_start)(env),;setenv bootargs $(bootargs)$(kernel_size)@$(kernel_start)(zImage),;setenv bootargs $(bootargs)$(initrd_size)@$(initrd_start)(initrd),;setenv bootargs $(bootargs)128m@0x0(flash); iomega=123 ethaddr=AA:00:00:00:00:01 arcNumber=1682 bootargs_root=root=LABEL=rootfs memoffset_kernel=0x00800000 memoffset_initrd=0x01000000 bootargs_combine=setenv bootargs ${bootargs_console} ${bootargs_mtdparts} ${bootargs_root} bootlinux=bootm ${memoffset_kernel} ${memoffset_initrd} usb_load_firstdevice=ext2load usb 0:1 ${memoffset_kernel} /uImage; ext2load usb 0:1 ${memoffset_initrd} /uInitrd usb_load=run bootargs_combine; usb reset; run usb_load_firstdevice; run bootlinux sata_load_disk1=ext2load ide 0:1 ${memoffset_kernel} /boot/uImage; ext2load ide 0:1 ${memoffset_initrd} /boot/uInitrd sata_load_disk2=ext2load ide 1:1 ${memoffset_kernel} /boot/uImage; ext2load ide 1:1 ${memoffset_initrd} /boot/uInitrd sata_load=run bootargs_combine; ide reset; run sata_load_disk1; run sata_load_disk2; run bootlinux mtdids=nand0=orion_nand bootargs_console=console=ttyS0,115200 mtdparts=orion_nand:0x100000@0x000000(uboot)ro,0x20000@0xA0000(uboot_env),0x300000@0x100000(uImage),0x1000000@0x1000000(uInitrd) root=LABEL=rootfs rootdelay=10 bootargs=console=ttyS0,115200 mtdparts=orion_nand:0x100000@0x000000(uboot)ro,0x20000@0xA0000(uboot_env),0x300000@0x100000(uImage),0x1000000@0x1000000(uInitrd) root=LABEL=rootfs rootdelay=10 mtdparts=mtdparts=orion_nand:0x100000@0x000000(uboot)ro,0x20000@0xA0000(uboot_env),0x300000@0x100000(uImage),0x1000000@0x1000000(uInitrd) partition=nand0,0 mtddevnum=0 mtddevname=uboot bootcmd=setenv bootargs $(bootargs_console) root=LABEL=rootfs; nand read 0x800000 uImage; nand read 0x2100000 uInitrd; bootm 0x00800000 stdin=serial stdout=serial stderr=serial mainlineLinux=yes enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no hddPowerCtrl=no enaAutoRecovery=yes ethact=egiga1 Environment size: 3364/16380 bytes Marvell>>
Re: ix2-200 boots USB but not HDD February 26, 2020 12:11AM |
Admin Registered: 13 years ago Posts: 18,495 |
setenv bootcmd_usb 'usb start; ext2load usb 0:1 0x800000 /boot/uImage; ext2load usb 0:1 0x2100000 /boot/uInitrd' setenv bootcmd_stock 'nand read 0x800000 uImage; nand read 0x2100000 uInitrd; bootm 0x00800000 0x2100000' setenv bootcmd 'setenv bootargs $(bootargs_console) root=LABEL=rootfs rootfdelay=10 earlyprintk=serial; run bootcmd_usb; run bootcmd_stock' boot
setenv bootcmd_usb 'usb start; ext2load usb 0:1 0x800000 /boot/uImage; ext2load usb 0:1 0x2100000 /boot/uInitrd' setenv bootcmd_stock 'nand read 0x800000 uImage; nand read 0x2100000 uInitrd; bootm 0x00800000 0x2100000' setenv bootcmd 'setenv bootargs $(bootargs_console) root=LABEL=rootfs rootfdelay=10 earlyprintk=serial; run bootcmd_usb; bootcmd_stock' saveenv
Re: ix2-200 boots USB but not HDD February 26, 2020 05:54AM |
Registered: 4 years ago Posts: 23 |
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** MARVELL BOARD: RD-88F6281A LE U-Boot 1.1.4 (Sep 8 2009 - 09:31:54) Marvell version: 3.4.14 Mapower version: 2.0 (32MB) (2009/09/08) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE60 Soc: 88F6281 A0 (DDR2) CPU running @ 1000Mhz L2 running @ 333Mhz SysClock = 333Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:32 MB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled Module 0 is RGMII Module 1 is TDM USB 0: host mode PEX 0: interface detected no Link. Net: egiga0, egiga1 [PRIME] Fan lookup table initialized. Current remote temperature: 33 Current fan speed: 0 Hit any key to stop autoboot: 0 Marvell>> setenv bootcmd_usb 'usb start; ext2load usb 0:1 0x800000 /boot/uImage; ext2load usb 0:1 0x2100000 /boot/uInitrd' Marvell>> setenv bootcmd_stock 'nand read 0x800000 uImage; nand read 0x2100000 uInitrd; bootm 0x00800000 0x2100000' Marvell>> setenv bootcmd 'setenv bootargs $(bootargs_console) root=LABEL=rootfs rootfdelay=10 earlyprintk=serial; run bootcmd_usb; run bootcmd_stock' Marvell>> boot (Re)start USB... USB: scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found .... . ...... ............ ......................... ................................................... ...................................................................................................... ................................................................................................................................................................................................................. ....................................................................... 4975416 bytes read . ... . ...... ............ ......................... ................................................... ...................................................................................................... ............................................................................................................................................................................................................ .... .................................................................................................................................................................................................................................................................................................................................................................................................................... .... ............................................................................................................................ 9713936 bytes read NAND read: device 0 offset 0x100000, size 0x300000 3145728 bytes read: OK NAND read: device 0 offset 0x1000000, size 0x1000000 16777216 bytes read: ERROR ## Booting image at 00800000 ... Image Name: Linux-3.16.0-6 Created: 2020-02-06 12:34:50 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2076864 Bytes = 2 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 02100000 ... Bad Magic Number
__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** MARVELL BOARD: RD-88F6281A LE U-Boot 1.1.4 (Sep 8 2009 - 09:31:54) Marvell version: 3.4.14 Mapower version: 2.0 (32MB) (2009/09/08) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE60 Soc: 88F6281 A0 (DDR2) CPU running @ 1000Mhz L2 running @ 333Mhz SysClock = 333Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:32 MB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled Module 0 is RGMII Module 1 is TDM USB 0: host mode PEX 0: interface detected no Link. Net: egiga0, egiga1 [PRIME] Fan lookup table initialized. Current remote temperature: 35 Current fan speed: 0 Hit any key to stop autoboot: 0 Marvell>> usb start (Re)start USB... USB: scanning bus for devices... 3 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Marvell>> ext2load usb 0:1 0x800000 /boot/uImage .... . ...... ............ ......................... ................................................... ...................................................................................................... ................................................................................................................................................................................................................. ....................................................................... 4975416 bytes read Marvell>> ext2load usb 0:1 0x2100000 /boot/uInitrd . ... . ...... ............ ......................... ................................................... ...................................................................................................... ............................................................................................................................................................................................................ .... .................................................................................................................................................................................................................................................................................................................................................................................................................... .... ............................................................................................................................ 9713936 bytes read Marvell>> setenv bootcmd 'setenv bootargs $(bootargs_console) root=LABEL=rootfs rootfdelay=10 earlyprintk=serial' Marvell>> bootm 0x00800000 0x2100000 ## Booting image at 00800000 ... Image Name: Linux-5.2.9-kirkwood-tld-1 Created: 2020-02-14 20:02:37 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4975352 Bytes = 4.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 02100000 ... Image Name: initrd.img-5.2.9-kirkwood-tld-1 Created: 2020-02-24 15:34:56 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 9713872 Bytes = 9.3 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.2.9-kirkwood-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 PREEMPT Sat Aug 17 15:00:56 PDT 2019 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Iomega StorCenter ix2-200 [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 65024 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:0x100000@0x000000(uboot)ro,0x20000@0xA0000(uboot_env),0x300000@0x100000(uImage),0x1000000@0x1000000(uInitrd) root=LABEL=rootfs rootdelay=10 [ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000][ T0] Memory: 234780K/262144K available (9216K kernel code, 868K rwdata, 3400K rodata, 1024K init, 301K bss, 27364K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from cache_alloc_refill+0x38c/0x928 with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000011][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000057][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.000957][ T0] Console: colour dummy device 80x30 [ 0.001018][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.001048][ T0] pid_max: default: 32768 minimum: 301 [ 0.001489][ T0] LSM: Security Framework initializing [ 0.001709][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001741][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.002758][ T0] *** VALIDATE proc *** [ 0.003065][ T0] *** VALIDATE cgroup1 *** [ 0.003096][ T0] *** VALIDATE cgroup2 *** [ 0.003211][ T0] CPU: Testing write buffer coherency: ok [ 0.005213][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.005568][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.005912][ T1] rcu: Hierarchical SRCU implementation. [ 0.009736][ T1] devtmpfs: initialized [ 0.016684][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.016722][ T1] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.017018][ T1] xor: measuring software checksum speed [ 0.110142][ T1] arm4regs : 902.400 MB/sec [ 0.210094][ T1] 8regs : 542.000 MB/sec [ 0.310089][ T1] 32regs : 788.000 MB/sec [ 0.310113][ T1] xor: using function: arm4regs (902.400 MB/sec) [ 0.310138][ T1] prandom: seed boundary self test passed [ 0.315172][ T1] prandom: 100 self tests passed [ 0.315186][ T1] pinctrl core: initialized pinctrl subsystem [ 0.316890][ T1] NET: Registered protocol family 16 [ 0.317561][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.318533][ T1] audit: initializing netlink subsys (disabled) [ 0.320031][ T14] audit: type=2000 audit(0.310:1): state=initialized audit_enabled=0 res=1 [ 0.320228][ T1] cpuidle: using governor ladder [ 0.320318][ T1] cpuidle: using governor menu [ 0.320971][ T1] Feroceon L2: Enabling L2 [ 0.321029][ T1] Feroceon L2: Cache support initialised. [ 0.328289][ T1] No ATAGs? [ 2.560066][ C0] random: fast init done [ 7.479675][ T71] alg: No test for lzo-rle (lzo-rle-generic) [ 7.480319][ T73] alg: No test for lzo-rle (lzo-rle-scomp) [ 7.661035][ T1] raid6: int32x8 gen() 106 MB/s [ 7.830448][ T1] raid6: int32x8 xor() 72 MB/s [ 8.000252][ T1] raid6: int32x4 gen() 107 MB/s [ 8.170234][ T1] raid6: int32x4 xor() 69 MB/s [ 8.340088][ T1] raid6: int32x2 gen() 110 MB/s [ 8.510147][ T1] raid6: int32x2 xor() 78 MB/s [ 8.680540][ T1] raid6: int32x1 gen() 83 MB/s [ 8.850200][ T1] raid6: int32x1 xor() 57 MB/s [ 8.850213][ T1] raid6: using algorithm int32x2 gen() 110 MB/s [ 8.850224][ T1] raid6: .... xor() 78 MB/s, rmw enabled [ 8.850234][ T1] raid6: using intx1 recovery algorithm [ 8.850573][ T1] vgaarb: loaded [ 8.851188][ T1] SCSI subsystem initialized [ 8.851813][ T1] usbcore: registered new interface driver usbfs [ 8.851890][ T1] usbcore: registered new interface driver hub [ 8.851993][ T1] usbcore: registered new device driver usb [ 8.852212][ T1] pps_core: LinuxPPS API ver. 1 registered [ 8.852226][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 8.852260][ T1] PTP clock support registered [ 8.853876][ T1] clocksource: Switched to clocksource orion_clocksource [ 10.098959][ T1] VFS: Disk quotas dquot_6.6.0 [ 10.099072][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 10.110955][ T1] NET: Registered protocol family 2 [ 10.111975][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes) [ 10.112018][ T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 10.112061][ T1] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 10.112099][ T1] TCP: Hash tables configured (established 2048 bind 2048) [ 10.112224][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 10.112257][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 10.112539][ T1] NET: Registered protocol family 1 [ 10.113324][ T1] RPC: Registered named UNIX socket transport module. [ 10.113341][ T1] RPC: Registered udp transport module. [ 10.113352][ T1] RPC: Registered tcp transport module. [ 10.113362][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 10.113380][ T1] PCI: CLS 0 bytes, default 32 [ 10.113679][ T1] Trying to unpack rootfs image as initramfs... [ 11.121431][ T1] Freeing initrd memory: 9488K [ 11.121661][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 11.123200][ T1] Initialise system trusted keyrings [ 11.123261][ T1] Key type blacklist registered [ 11.123541][ T1] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 11.123674][ T1] zbud: loaded [ 11.125174][ T1] NFS: Registering the id_resolver key type [ 11.125222][ T1] Key type id_resolver registered [ 11.125234][ T1] Key type id_legacy registered [ 11.125259][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 11.125279][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 11.125634][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 11.125910][ T1] fuse: init (API version 7.31) [ 11.126404][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 11.126620][ T1] orangefs_init: module version upstream loaded [ 11.126636][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, no debug enabled [ 11.147768][ T1] async_tx: api initialized (async) [ 11.147798][ T1] Key type asymmetric registered [ 11.147810][ T1] Asymmetric key parser 'x509' registered [ 11.147897][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 11.149863][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 11.152383][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 11.214888][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 11.217326][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 11.274864][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 11.277652][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 11.279175][ T1] printk: console [ttyS0] disabled [ 11.279266][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 12.041029][ T1] printk: console [ttyS0] enabled [ 12.055322][ T1] loop: module loaded [ 12.059881][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 12.068931][ T1] scsi host0: sata_mv [ 12.073495][ T1] scsi host1: sata_mv [ 12.077792][ T1] ata1: SATA max UDMA/133 irq 33 [ 12.082616][ T1] ata2: SATA max UDMA/133 irq 33 [ 12.088855][ T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0x75 [ 12.096052][ T1] nand: Hynix NAND 32MiB 3,3V 8-bit [ 12.101139][ T1] nand: 32 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16 [ 12.109235][ T1] Scanning device for bad blocks [ 12.212747][ T1] Bad eraseblock 895 at 0x000000dfc000 [ 12.298152][ T1] Bad eraseblock 1622 at 0x000001958000 [ 12.350612][ T1] 4 cmdlinepart partitions found on MTD device orion_nand [ 12.357657][ T1] Creating 4 MTD partitions on "orion_nand": [ 12.363558][ T1] 0x000000000000-0x000000100000 : "uboot" [ 12.370869][ T1] 0x0000000a0000-0x0000000c0000 : "uboot_env" [ 12.378403][ T1] 0x000000100000-0x000000400000 : "uImage" [ 12.385752][ T1] 0x000001000000-0x000002000000 : "uInitrd" [ 12.395095][ T1] libphy: Fixed MDIO Bus: probed [ 12.400926][ T1] libphy: orion_mdio_bus: probed [ 12.422933][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 12.431771][ T1] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set [ 12.439381][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address aa:00:00:00:00:01 [ 12.449048][ T1] mv643xx_eth_port mv643xx_eth_port.1: DMA mask not set [ 12.583928][ T112] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 12.616276][ T112] ata1.00: ATA-8: WDC WD20EARX-00PASB0, 51.0AB51, max UDMA/133 [ 12.623712][ T112] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 12.656271][ T112] ata1.00: configured for UDMA/133 [ 12.671871][ T7] scsi 0:0:0:0: Direct-Access ATA WDC WD20EARX-00P AB51 PQ: 0 ANSI: 5 [ 12.681921][ T116] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB) [ 12.690993][ T116] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 12.697143][ T116] sd 0:0:0:0: [sda] Write Protect is off [ 12.702813][ T116] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 13.025577][ T114] ata2: SATA link down (SStatus 0 SControl F300) [ 13.142081][ T116] sda: sda1 [ 13.146984][ T116] sd 0:0:0:0: [sda] Attached SCSI disk [ 13.174655][ T1] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:50:43:a0:0a:27 [ 13.184313][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 13.191598][ T1] ehci-pci: EHCI PCI platform driver [ 13.196858][ T1] ehci-orion: EHCI orion driver [ 13.201855][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 13.208139][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 13.216862][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 13.243925][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 13.251010][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02 [ 13.260053][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 13.268038][ T1] usb usb1: Product: EHCI Host Controller [ 13.273638][ T1] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-1 ehci_hcd [ 13.281012][ T1] usb usb1: SerialNumber: f1050000.ehci [ 13.287193][ T1] hub 1-0:1.0: USB hub found [ 13.291716][ T1] hub 1-0:1.0: 1 port detected [ 13.297271][ T1] usbcore: registered new interface driver usb-storage [ 13.304525][ T1] mousedev: PS/2 mouse device common for all mice [ 13.311513][ T1] rtc-mv f1010300.rtc: registered as rtc0 [ 13.317372][ T1] i2c /dev entries driver [ 13.323337][ T1] device-mapper: uevent: version 1.0.3 [ 13.329115][ T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com [ 13.338836][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 13.346180][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 13.353528][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 13.361006][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 13.367862][ T1] device-mapper: raid: Loading target version 1.14.0 [ 13.376071][ T1] hidraw: raw HID events driver (C) Jiri Kosina [ 13.382589][ T1] drop_monitor: Initializing network drop monitor service [ 13.390010][ T1] NET: Registered protocol family 17 [ 13.395506][ T1] Key type dns_resolver registered [ 13.401502][ T1] registered taskstats version 1 [ 13.406524][ T1] Loading compiled-in X.509 certificates [ 13.412126][ T1] zswap: loaded using pool lzo/zbud [ 13.528537][ T1] Key type big_key registered [ 13.583564][ T1] Key type encrypted registered [ 13.590858][ T1] rtc-mv f1010300.rtc: setting system clock to 2020-02-26T11:17:19 UTC (1582715839) [ 13.604453][ T1] Freeing unused kernel memory: 1024K [ 13.614551][ T1] Checked W+X mappings: passed, no W+X pages found [ 13.620945][ T1] Run /init as init process [ 13.664036][ T15] usb 1-1: new high-speed USB device number 2 using orion-ehci Loading, please wait... Starting version 241 [ 13.864648][ T15] usb 1-1: New USB device found, idVendor=058f, idProduct=6254, bcdDevice= 1.00 [ 13.873601][ T15] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 13.907999][ T15] hub 1-1:1.0: USB hub found [ 13.928402][ T15] hub 1-1:1.0: 4 ports detected [ 14.253991][ T15] usb 1-1.1: new high-speed USB device number 3 using orion-ehci [ 14.426521][ T15] usb 1-1.1: New USB device found, idVendor=154b, idProduct=005b, bcdDevice=11.00 [ 14.451387][ T15] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 14.477517][ T15] usb 1-1.1: Product: USB 2.0 FD [ 14.482345][ T15] usb 1-1.1: Manufacturer: PNY Technologies [ 14.509520][ T15] usb 1-1.1: SerialNumber: AD1CHD1200000071 [ 14.528905][ T15] usb-storage 1-1.1:1.0: USB Mass Storage device detected [ 14.558148][ T15] scsi host2: usb-storage 1-1.1:1.0 [ 14.658037][ T170] usbcore: registered new interface driver uas Begin: Loading essential drivers ... done. [ 16.300743][ T23] scsi 2:0:0:0: Direct-Access PNY USB 2.0 FD 1100 PQ: 0 ANSI: 4 [ 16.314069][ T116] sd 2:0:0:0: [sdb] 15814656 512-byte logical blocks: (8.10 GB/7.54 GiB) [ 16.331395][ T116] sd 2:0:0:0: [sdb] Write Protect is off [ 16.339551][ T116] sd 2:0:0:0: [sdb] No Caching mode page found [ 16.345698][ T116] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 16.359947][ T116] sdb: sdb1 [ 16.377308][ T116] sd 2:0:0:0: [sdb] Attached SCSI removable disk Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.33.1 fsck: error 2 (No such file or directory) while executing fsck.ext2 for /dev/sdb1 fsck exited with status code 8 done. Warning: File system check failed but did not detect errors done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.93 booting [info] Using makefile-style concurrent boot in runlevel S. [ ok ] Starting hotplug events dispatcher: systemd-udevd. [ ok ] Synthesizing the initial hotplug events (subsystems)...done. [....] Synthesizing the initial hotplug events (devices)...[ 33.471560][ T394] input: gpio-keys as /devices/platform/gpio-keys/input/input0 done. [....] Waiting for /dev to be fully populated...[ 33.747154][ T372] systemd-udevd[372]: Using default interface naming scheme 'v240'. [ 33.809093][ T373] systemd-udevd[373]: Using default interface naming scheme 'v240'. [ 33.849883][ T372] systemd-udevd[372]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 33.956311][ T373] systemd-udevd[373]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. [ 34.115430][ T376] watchdog: f1020300.watchdog-timer: driver supplied timeout (4294967295) out of range [ 34.215047][ C0] random: crng init done [ 34.272800][ T376] watchdog: f1020300.watchdog-timer: falling back to default timeout (21) [ 34.451926][ T376] orion_wdt: Initial timeout 21 sec [ 34.485141][ T375] marvell-cesa f1030000.crypto: CESA device successfully registered [ 34.525237][ T374] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 34.572846][ T374] sd 2:0:0:0: Attached scsi generic sg1 type 0 [ 34.827661][ T394] systemd-udevd[394]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable. done. [ ok ] Setting hostname to 'debian'...done. [ ok ] Activating swap:. [....] Will now check root file system:fsck from util-linux 2.33.1 [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /run/rootdev e2fsck 1.44.5 (15-Dec-2018) rootfs: clean, 15085/494832 files, 182877/1976576 blocks . ok [info] Will now check all file systems. fsck from util-linux 2.33.1 Checking all file systems. LABEL=rootfs is not mounted [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sda1 e2fsck 1.44.5 (15-Dec-2018) rootfs: recovering journal rootfs: clean, 15077/122101760 files, 8133909/488378390 blocks [ ok ] Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable.. [ ok ] Cleaning up temporary files...[....] Cleaning /tmp...done. [ ok . [ ok ] Will now mount local filesystems:. [ ok ] Will now activate swapfile swap:done. [ ok ] Checking minimum space in /tmp...done. [ ok ] Cleaning up temporary files.... [ ok ] Starting Setting kernel variables: sysctl. [ ok ] Initializing random number generator...done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ [ 71.383483][ T1153] mv643xx_eth: no PHY [ 71.383535][ C0] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled Listening on LPF/eth0/aa:00:00:00:00:01 Sending on LPF/eth0/aa:00:00:00:00:01 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 6 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 10 No DHCPOFFERS received. No working leases in persistent database - sleeping. done. [....] Starting RPC port mapper daemon: rpcbind[ 132.883091][ T1235] NET: Registered protocol family 10 [ 132.891185][ T1235] Segment Routing with IPv6 . ok [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Cleaning up temporary files.... INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd... 1359 (syslogd) . ok [....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd... 1386 (klogd) . ok [ ok ] Starting system message bus: dbus. [ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon. [ ok ] Starting NFS common utilities: statd idmapd. [warn] Not starting NFS kernel daemon: no exports. ... (warning). [ ok ] Starting NTP server: ntpd. [ ok ] Starting OpenBSD Secure Shell server: sshd. [ ok ] Running local boot scripts (/etc/rc.local). Debian GNU/Linux 10 debian ttyS0 debian login:
Re: ix2-200 boots USB but not HDD February 26, 2020 07:00AM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: ix2-200 boots USB but not HDD February 26, 2020 08:21AM |
Registered: 4 years ago Posts: 23 |
root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 00100000 00004000 "uboot" mtd1: 00020000 00004000 "uboot_env" mtd2: 00300000 00004000 "uImage" mtd3: 01000000 00004000 "uInitrd" root@debian:~# ls -al /boot total 65492 drwxr-xr-x 3 root root 4096 Feb 24 07:34 . drwxr-xr-x 22 root root 4096 Feb 25 06:41 .. -rw------- 1 root root 3101889 Aug 17 2019 System.map-5.2.9-kirkwood-tld-1 -rw-r--r-- 1 root root 165790 Aug 17 2019 config-5.2.9-kirkwood-tld-1 drwxr-xr-x 2 root root 4096 Aug 16 2019 dts -rw-r--r-- 1 root root 9713872 Aug 24 2019 initrd.img-5.2.9-kirkwood-tld-1 -rw-r--r-- 1 root root 9649570 Aug 17 2019 linux-headers-5.2.9-kirkwood-tld-1_1.0_armel.deb -rw-r--r-- 1 root root 4975416 Feb 14 12:02 uImage -rw-r--r-- 1 root root 4963680 Aug 24 2019 uImage.orig -rw-r--r-- 1 root root 9713936 Feb 24 07:34 uInitrd -rw-r--r-- 1 root root 9713936 Aug 24 2019 uInitrd.orig -rw------- 1 root root 4963616 Aug 17 2019 vmlinuz-5.2.9-kirkwood-tld-1 -rwxr-xr-x 1 root root 4963616 Aug 17 2019 zImage-5.2.9-kirkwood-tld-1 -rwxr-xr-x 1 root root 4975352 Feb 14 12:00 zImage.fdt root@debian:~# flash_eraseall /dev/mtd2 flash_eraseall has been replaced by `flash_erase <mtddev> 0 0`; please use it Erasing 16 Kibyte @ 2fc000 -- 100 % complete root@debian:~# nandwrite -p /dev/mtd2 /boot/uImage Image 4975416 bytes, NAND page 512 bytes, OOB area 16 bytes, device size 3145728 bytes nandwrite: error!: Input file does not fit into device error 0 (Success) nandwrite: error!: Data was only partially written due to error error 0 (Success)
root@debian:~# dmesg |grep 0x0 [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:0x100000@0x000000(uboot)ro,0x20000@0xA0000(uboot_env),0x300000@0x100000(uImage),0x1000000@0x1000000(uInitrd) root=LABEL=rootfs rootdelay=10 [ 12.212747] Bad eraseblock 895 at 0x000000dfc000 [ 12.298152] Bad eraseblock 1622 at 0x000001958000 [ 12.363558] 0x000000000000-0x000000100000 : "uboot" [ 12.370869] 0x0000000a0000-0x0000000c0000 : "uboot_env" [ 12.378403] 0x000000100000-0x000000400000 : "uImage" [ 12.385752] 0x000001000000-0x000002000000 : "uInitrd"
Re: ix2-200 boots USB but not HDD February 26, 2020 01:55PM |
Registered: 4 years ago Posts: 23 |
setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(uboot)ro,0x20000@0xA0000(uboot_env),0x500000@0x100000(uImage),0xE00000@0x1000000(uInitrd)'
root@debian:~# dmesg | grep 0x0 [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:0x100000@0x000000(uboot)ro,0x20000@0xA0000(uboot_env),0x500000@0x100000(uImage),0x1000000@0x1000000(uInitrd) root=LABEL=rootfs rootdelay=10 [ 12.212769] Bad eraseblock 895 at 0x000000dfc000 [ 12.298173] Bad eraseblock 1622 at 0x000001958000 [ 12.363579] 0x000000000000-0x000000100000 : "uboot" [ 12.370894] 0x0000000a0000-0x0000000c0000 : "uboot_env" [ 12.378431] 0x000000100000-0x000000600000 : "uImage" [ 12.385845] 0x000001000000-0x000002000000 : "uInitrd" root@debian:~# cat /proc/mtd dev: size erasesize name mtd0: 00100000 00004000 "uboot" mtd1: 00020000 00004000 "uboot_env" mtd2: 00500000 00004000 "uImage" mtd3: 01000000 00004000 "uInitrd" root@debian:~#
Re: ix2-200 boots USB but not HDD February 26, 2020 02:07PM |
Registered: 4 years ago Posts: 23 |
Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x500000 5242880 bytes read: OK NAND read: device 0 offset 0x1000000, size 0xe00000 14680064 bytes read: ERROR ## Booting image at 00800000 ... Image Name: Linux-5.2.9-kirkwood-tld-1 Created: 2020-02-14 20:02:37 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4975352 Bytes = 4.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 5.2.9-kirkwood-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 PREEMPT Sat Aug 17 15:00:56 PDT 2019 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Iomega StorCenter ix2-200 [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 65024 [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:0x100000@0x000000(uboot)ro,0x20000@0xA0000(uboot_env),0x500000@0x100000(uImage),0x1000000@0x1000000(uInitrd) root=LABEL=rootfs rootdelay=10 root=LABEL=rootfs [ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000][ T0] Memory: 244268K/262144K available (9216K kernel code, 868K rwdata, 3400K rodata, 1024K init, 301K bss, 17876K reserved, 0K cma-reserved) [ 0.000000][ T0] random: get_random_u32 called from cache_alloc_refill+0x38c/0x928 with crng_init=0 [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000010][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000056][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.000950][ T0] Console: colour dummy device 80x30 [ 0.001011][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.001040][ T0] pid_max: default: 32768 minimum: 301 [ 0.001484][ T0] LSM: Security Framework initializing [ 0.001704][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001734][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.002754][ T0] *** VALIDATE proc *** [ 0.003061][ T0] *** VALIDATE cgroup1 *** [ 0.003091][ T0] *** VALIDATE cgroup2 *** [ 0.003207][ T0] CPU: Testing write buffer coherency: ok [ 0.005226][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.005583][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2 [ 0.005928][ T1] rcu: Hierarchical SRCU implementation. [ 0.009750][ T1] devtmpfs: initialized [ 0.016739][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.016776][ T1] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.017073][ T1] xor: measuring software checksum speed [ 0.110133][ T1] arm4regs : 902.400 MB/sec [ 0.210092][ T1] 8regs : 542.000 MB/sec [ 0.310084][ T1] 32regs : 787.600 MB/sec [ 0.310107][ T1] xor: using function: arm4regs (902.400 MB/sec) [ 0.310133][ T1] prandom: seed boundary self test passed [ 0.315169][ T1] prandom: 100 self tests passed [ 0.315183][ T1] pinctrl core: initialized pinctrl subsystem [ 0.316872][ T1] NET: Registered protocol family 16 [ 0.317570][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.318541][ T1] audit: initializing netlink subsys (disabled) [ 0.320022][ T14] audit: type=2000 audit(0.310:1): state=initialized audit_enabled=0 res=1 [ 0.320222][ T1] cpuidle: using governor ladder [ 0.320312][ T1] cpuidle: using governor menu [ 0.320993][ T1] Feroceon L2: Enabling L2 [ 0.321052][ T1] Feroceon L2: Cache support initialised. [ 0.328291][ T1] No ATAGs? [ 2.560064][ C0] random: fast init done [ 7.479456][ T71] alg: No test for lzo-rle (lzo-rle-generic) [ 7.479899][ T73] alg: No test for lzo-rle (lzo-rle-scomp) [ 7.660890][ T1] raid6: int32x8 gen() 106 MB/s [ 7.830430][ T1] raid6: int32x8 xor() 72 MB/s [ 8.000185][ T1] raid6: int32x4 gen() 107 MB/s [ 8.170232][ T1] raid6: int32x4 xor() 69 MB/s [ 8.340600][ T1] raid6: int32x2 gen() 110 MB/s [ 8.510148][ T1] raid6: int32x2 xor() 78 MB/s [ 8.680538][ T1] raid6: int32x1 gen() 83 MB/s [ 8.850199][ T1] raid6: int32x1 xor() 57 MB/s [ 8.850213][ T1] raid6: using algorithm int32x2 gen() 110 MB/s [ 8.850223][ T1] raid6: .... xor() 78 MB/s, rmw enabled [ 8.850233][ T1] raid6: using intx1 recovery algorithm [ 8.850564][ T1] vgaarb: loaded [ 8.851174][ T1] SCSI subsystem initialized [ 8.851799][ T1] usbcore: registered new interface driver usbfs [ 8.851877][ T1] usbcore: registered new interface driver hub [ 8.851981][ T1] usbcore: registered new device driver usb [ 8.852206][ T1] pps_core: LinuxPPS API ver. 1 registered [ 8.852220][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 8.852253][ T1] PTP clock support registered [ 8.853892][ T1] clocksource: Switched to clocksource orion_clocksource [ 10.099100][ T1] VFS: Disk quotas dquot_6.6.0 [ 10.099215][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 10.111096][ T1] NET: Registered protocol family 2 [ 10.112110][ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes) [ 10.112155][ T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 10.112198][ T1] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 10.112236][ T1] TCP: Hash tables configured (established 2048 bind 2048) [ 10.112353][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 10.112385][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 10.112671][ T1] NET: Registered protocol family 1 [ 10.113447][ T1] RPC: Registered named UNIX socket transport module. [ 10.113464][ T1] RPC: Registered udp transport module. [ 10.113474][ T1] RPC: Registered tcp transport module. [ 10.113485][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 10.113502][ T1] PCI: CLS 0 bytes, default 32 [ 10.114110][ T1] NetWinder Floating Point Emulator V0.97 (double precision) [ 10.115532][ T1] Initialise system trusted keyrings [ 10.115595][ T1] Key type blacklist registered [ 10.115864][ T1] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 10.115987][ T1] zbud: loaded [ 10.117307][ T1] NFS: Registering the id_resolver key type [ 10.117349][ T1] Key type id_resolver registered [ 10.117361][ T1] Key type id_legacy registered [ 10.117386][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 10.117405][ T1] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 10.117753][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 10.118033][ T1] fuse: init (API version 7.31) [ 10.118501][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 10.118747][ T1] orangefs_init: module version upstream loaded [ 10.118763][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, no debug enabled [ 10.122518][ T1] async_tx: api initialized (async) [ 10.122543][ T1] Key type asymmetric registered [ 10.122556][ T1] Asymmetric key parser 'x509' registered [ 10.122624][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 10.124671][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 10.127183][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 10.184858][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 10.187289][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 10.244896][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 10.247631][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 10.249160][ T1] printk: console [ttyS0] disabled [ 10.249245][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 11.001822][ T1] printk: console [ttyS0] enabled [ 11.016116][ T1] loop: module loaded [ 11.020661][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 11.029694][ T1] scsi host0: sata_mv [ 11.034345][ T1] scsi host1: sata_mv [ 11.038567][ T1] ata1: SATA max UDMA/133 irq 33 [ 11.043390][ T1] ata2: SATA max UDMA/133 irq 33 [ 11.049507][ T1] nand: device found, Manufacturer ID: 0xad, Chip ID: 0x75 [ 11.056701][ T1] nand: Hynix NAND 32MiB 3,3V 8-bit [ 11.061781][ T1] nand: 32 MiB, SLC, erase size: 16 KiB, page size: 512, OOB size: 16 [ 11.069870][ T1] Scanning device for bad blocks [ 11.173508][ T1] Bad eraseblock 895 at 0x000000dfc000 [ 11.258939][ T1] Bad eraseblock 1622 at 0x000001958000 [ 11.311422][ T1] 4 cmdlinepart partitions found on MTD device orion_nand [ 11.318467][ T1] Creating 4 MTD partitions on "orion_nand": [ 11.324385][ T1] 0x000000000000-0x000000100000 : "uboot" [ 11.331683][ T1] 0x0000000a0000-0x0000000c0000 : "uboot_env" [ 11.339212][ T1] 0x000000100000-0x000000600000 : "uImage" [ 11.346624][ T1] 0x000001000000-0x000002000000 : "uInitrd" [ 11.355951][ T1] libphy: Fixed MDIO Bus: probed [ 11.361792][ T1] libphy: orion_mdio_bus: probed [ 11.368105][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 11.376967][ T1] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set [ 11.384586][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address aa:00:00:00:00:01 [ 11.394214][ T1] mv643xx_eth_port mv643xx_eth_port.1: DMA mask not set [ 11.543947][ T112] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 12.023978][ T112] ata1.00: ATA-8: WDC WD20EARX-00PASB0, 51.0AB51, max UDMA/133 [ 12.031421][ T112] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 12.066280][ T112] ata1.00: configured for UDMA/133 [ 12.081891][ T7] scsi 0:0:0:0: Direct-Access ATA WDC WD20EARX-00P AB51 PQ: 0 ANSI: 5 [ 12.091992][ T116] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB) [ 12.101068][ T116] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 12.107216][ T116] sd 0:0:0:0: [sda] Write Protect is off [ 12.112889][ T116] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 12.123510][ T1] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:50:43:a0:0a:27 [ 12.134785][ T1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 12.142071][ T1] ehci-pci: EHCI PCI platform driver [ 12.147342][ T1] ehci-orion: EHCI orion driver [ 12.152305][ T116] sda: sda1 [ 12.155670][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 12.161918][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 12.172101][ T116] sd 0:0:0:0: [sda] Attached SCSI disk [ 12.177768][ T1] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 12.213929][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 12.221014][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02 [ 12.230053][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 12.238040][ T1] usb usb1: Product: EHCI Host Controller [ 12.243648][ T1] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-1 ehci_hcd [ 12.251021][ T1] usb usb1: SerialNumber: f1050000.ehci [ 12.257205][ T1] hub 1-0:1.0: USB hub found [ 12.261724][ T1] hub 1-0:1.0: 1 port detected [ 12.267292][ T1] usbcore: registered new interface driver usb-storage [ 12.274547][ T1] mousedev: PS/2 mouse device common for all mice [ 12.281541][ T1] rtc-mv f1010300.rtc: registered as rtc0 [ 12.287396][ T1] i2c /dev entries driver [ 12.293349][ T1] device-mapper: uevent: version 1.0.3 [ 12.299109][ T1] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com [ 12.308825][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 12.316173][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 12.323520][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 12.331017][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 12.337899][ T1] device-mapper: raid: Loading target version 1.14.0 [ 12.346141][ T1] hidraw: raw HID events driver (C) Jiri Kosina [ 12.352699][ T1] drop_monitor: Initializing network drop monitor service [ 12.360130][ T1] NET: Registered protocol family 17 [ 12.365654][ T1] Key type dns_resolver registered [ 12.371725][ T1] registered taskstats version 1 [ 12.376770][ T1] Loading compiled-in X.509 certificates [ 12.382424][ T1] zswap: loaded using pool lzo/zbud [ 12.406093][ T1] Key type big_key registered [ 12.414953][ T1] Key type encrypted registered [ 12.422061][ T1] rtc-mv f1010300.rtc: setting system clock to 2020-02-26T19:13:04 UTC (1582744384) [ 12.432065][ T1] Waiting 10 sec before mounting root device... [ 12.603941][ T114] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 12.633934][ T15] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 12.834405][ T15] usb 1-1: New USB device found, idVendor=058f, idProduct=6254, bcdDevice= 1.00 [ 12.843339][ T15] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 12.852222][ T15] hub 1-1:1.0: USB hub found [ 12.857021][ T15] hub 1-1:1.0: 4 ports detected [ 12.914000][ T114] ata2.00: ATA-8: WDC WD20EARX-00PASB0, 51.0AB51, max UDMA/133 [ 12.921436][ T114] ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 12.956276][ T114] ata2.00: configured for UDMA/133 [ 12.971863][ T23] scsi 1:0:0:0: Direct-Access ATA WDC WD20EARX-00P AB51 PQ: 0 ANSI: 5 [ 12.981948][ T116] sd 1:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB) [ 12.990883][ T116] sd 1:0:0:0: [sdb] 4096-byte physical blocks [ 12.997080][ T116] sd 1:0:0:0: [sdb] Write Protect is off [ 13.002755][ T116] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 13.061563][ T116] sdb: [ 13.065823][ T116] sd 1:0:0:0: [sdb] Attached SCSI disk [ 22.884018][ T1] md: Waiting for all devices to be available before autodetect [ 22.891547][ T1] md: If you don't use raid, use raid=noautodetect [ 22.899017][ T1] md: Autodetecting RAID arrays. [ 22.903834][ T1] md: autorun ... [ 22.907423][ T1] md: ... autorun DONE. [ 22.911684][ T1] VFS: Cannot open root device "LABEL=rootfs" or unknown-block(0,0): error -6 [ 22.920500][ T1] Please append a correct "root=" boot option; here are the available partitions: [ 22.929699][ T1] 1f00 1024 mtdblock0 [ 22.929703][ T1] (driver?) [ 22.937740][ T1] 1f01 128 mtdblock1 [ 22.937744][ T1] (driver?) [ 22.945765][ T1] 1f02 5120 mtdblock2 [ 22.945769][ T1] (driver?) [ 22.953736][ T1] 1f03 16384 mtdblock3 [ 22.953739][ T1] (driver?) [ 22.961733][ T1] 0800 1953514584 sda [ 22.961738][ T1] driver: sd [ 22.969292][ T1] 0801 1953513560 sda1 51bdcac3-01 [ 22.969295][ T1] [ 22.977117][ T1] 0810 1953514584 sdb [ 22.977120][ T1] driver: sd [ 22.984671][ T1] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 22.993683][ T1] CPU: 0 PID: 1 Comm: swapper Not tainted 5.2.9-kirkwood-tld-1 #1 [ 23.001374][ T1] Hardware name: Marvell Kirkwood (Flattened Device Tree) [ 23.008399][ T1] [<c010f6ac>] (unwind_backtrace) from [<c010bb00>] (show_stack+0x10/0x14) [ 23.016898][ T1] [<c010bb00>] (show_stack) from [<c0119fa0>] (panic+0xe0/0x30c) [ 23.024519][ T1] [<c0119fa0>] (panic) from [<c0e01628>] (mount_block_root+0x1bc/0x2a4) [ 23.032745][ T1] [<c0e01628>] (mount_block_root) from [<c0e017f8>] (mount_root+0xe8/0x154) [ 23.041316][ T1] [<c0e017f8>] (mount_root) from [<c0e019b0>] (prepare_namespace+0x14c/0x18c) [ 23.050062][ T1] [<c0e019b0>] (prepare_namespace) from [<c0e011c8>] (kernel_init_freeable+0x270/0x2dc) [ 23.059682][ T1] [<c0e011c8>] (kernel_init_freeable) from [<c09dcee0>] (kernel_init+0x8/0x10c) [ 23.068601][ T1] [<c09dcee0>] (kernel_init) from [<c01010e0>] (ret_from_fork+0x14/0x34) [ 23.076901][ T1] Exception stack(0xcf88bfb0 to 0xcf88bff8) [ 23.082676][ T1] bfa0: 00000000 00000000 00000000 00000000 [ 23.091590][ T1] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 23.100509][ T1] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 23.107861][ T1] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---
Re: ix2-200 boots USB but not HDD February 26, 2020 07:02PM |
Admin Registered: 13 years ago Posts: 18,495 |
Re: ix2-200 boots USB but not HDD February 27, 2020 07:55AM |
Registered: 4 years ago Posts: 23 |
setenv bootcmd 'setenv bootargs $(bootargs_console) root=LABEL=rootfs rootfdelay=10 earlyprintk=serial; run bootcmd_usb; bootcmd_stock'
setenv bootcmd 'setenv bootargs $(bootargs_console) root=LABEL=rootfs rootfdelay=10 earlyprintk=serial; run bootcmd_usb; run bootcmd_stock'
Marvell>> printenv baudrate=115200 loads_echo=0 ipaddr=10.4.50.165 serverip=10.4.50.5 rootpath=/mnt/ARM_FS/ netmask=255.255.255.0 console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x1f00000@0x100000(root) CASset=min MALLOC_len=1 ethprime=egiga1 bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000; ethmtu=1500 eth1addr=00:50:43:a0:0a:27 eth1mtu=1500 mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host yuk_ethaddr=00:00:00:EE:51:81 nandEcc=1bit netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no FanHysteresis=2 FanTempStart=58 uboot_start=0x0 uboot_size=0xc0000 env_start=0xa0000 env_size=0x20000 kernel_start=0x100000 kernel_size=0x300000 initrd_start=0x540000 initrd_size=0x300000 flash_load=run make_boot_args load1 load2 boot load1=nand read.e 0x2000000 $(kernel_start) $(kernel_size) load2=nand read.e 0x4500000 $(initrd_start) $(initrd_size) boot=bootm 0x2000000 0x4500000 make_boot_args=setenv bootargs console=ttyS0,115200 mtdparts=nand_mtd:;setenv bootargs $(bootargs)$(uboot_size)@$(uboot_start)(uboot),;setenv bootargs $(bootargs)$(env_size)@$(env_start)(env),;setenv bootargs $(bootargs)$(kernel_size)@$(kernel_start)(zImage),;setenv bootargs $(bootargs)$(initrd_size)@$(initrd_start)(initrd),;setenv bootargs $(bootargs)128m@0x0(flash); iomega=123 ethaddr=AA:00:00:00:00:01 arcNumber=1682 bootargs_root=root=LABEL=rootfs memoffset_kernel=0x00800000 memoffset_initrd=0x01000000 mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:0x100000@0x000000(uboot)ro,0x20000@0xA0000(uboot_env),0x500000@0x100000(uImage),0xE00000@0x1000000(uInitrd) partition=nand0,0 mtddevnum=0 mtddevname=uboot bootargs_console=console=ttyS0,115200 mtdparts=orion_nand:0x100000@0x000000(uboot)ro,0x20000@0xA0000(uboot_env),0x500000@0x100000(uImage),0xE00000@0x1000000(uInitrd) root=LABEL=rootfs rootdelay=10 bootargs_combine=setenv bootargs ${bootargs_console} ${bootargs_mtdparts} ${bootargs_root} bootlinux=bootm ${memoffset_kernel} ${memoffset_initrd} usb_load_firstdevice=ext2load usb 0:1 ${memoffset_kernel} /boot/uImage; ext2load usb 0:1 ${memoffset_initrd} /boot/uInitrd usb_load=run bootargs_combine; usb reset; run usb_load_firstdevice; run bootlinux sata_load_disk1=ext2load ide 0:1 ${memoffset_kernel} /boot/uImage; ext2load ide 0:1 ${memoffset_initrd} /boot/uInitrd sata_load_disk2=ext2load ide 1:1 ${memoffset_kernel} /boot/uImage; ext2load ide 1:1 ${memoffset_initrd} /boot/uInitrd sata_load=run bootargs_combine; ide reset; run sata_load_disk1; run sata_load_disk2; run bootlinux bootargs=console=ttyS0,115200 mtdparts=orion_nand:0x100000@0x000000(uboot)ro,0x20000@0xA0000(uboot_env),0x500000@0x100000(uImage),0xE00000@0x1000000(uInitrd) root=LABEL=rootfs rootdelay=10 root=LABEL=rootfs rootfdelay=10 earlyprintk=serial bootcmd_usb=usb start; ext2load usb 0:1 0x800000 /boot/uImage; ext2load usb 0:1 0x2100000 /boot/uInitrd bootcmd_stock=nand read 0x800000 uImage; nand read 0x2100000 uInitrd; bootm 0x00800000 0x2100000 bootcmd=setenv bootargs $(bootargs_console) root=LABEL=rootfs rootfdelay=10 earlyprintk=serial; run bootcmd_usb; run bootcmd_stock stdin=serial stdout=serial stderr=serial mainlineLinux=yes enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no bootdelay=3 disaMvPnp=no hddPowerCtrl=no enaAutoRecovery=yes ethact=egiga1 Environment size: 3618/16380 bytes Marvell>>
Re: ix2-200 boots USB but not HDD February 27, 2020 06:25PM |
Admin Registered: 13 years ago Posts: 18,495 |