Sequence to Update Pogo E02 February 07, 2020 04:04PM |
Registered: 10 years ago Posts: 155 |
U-Boot 2011.12 (Feb 20 2012 - 21:21:59) BTW, is this the orignal Pogo u boot. or perhaps Jeff's first Kirkwood u boot?
Re: Sequence to Update Pogo E02 February 07, 2020 04:52PM |
Admin Registered: 13 years ago Posts: 18,821 |
cd /boot cp -a uImage uImmage.pogo_eo2 cp -a uImage.orig uImmage
cd /boot/dts mv kirkwood_pogo_e02.dtb kirkwood_pogo_e02.bak
Re: Sequence to Update Pogo E02 February 07, 2020 05:21PM |
Registered: 10 years ago Posts: 155 |
ethact=egiga0 bootdelay=3 baudrate=115200 mainlineLinux=yes console=ttyS0,115200 led_init=green blinking led_exit=green off led_error=orange blinking mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) mtdids=nand0=orion_nand partition=nand0,2 stdin=serial stdout=serial stderr=serial rescue_installed=0 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done usb_scan_list=1 2 3 4 usb_scan_1=usb=0:1 dev=sda1 usb_scan_2=usb=1:1 dev=sdb1 usb_scan_3=usb=2:1 dev=sdc1 usb_scan_4=usb=3:1 dev=sdd1 usb_init=run usb_scan usb_device=0:1 usb_root=/dev/sda1 usb_rootdelay=10 usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset ethaddr=00:25:31:00:BD:CF machid=dd6 usb_rootfstype=ext3
Re: Sequence to Update Pogo E02 February 07, 2020 05:33PM |
Admin Registered: 13 years ago Posts: 18,821 |
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi