RN10400
Posted by AkkJaa
|
Re: RN10400 January 28, 2021 07:14AM |
Registered: 3 years ago Posts: 116 |
Hi Bodhi,
Yes but the USB drive is sdc1 and not sdb1 so how get it over to the USB drive.?? 2 diffrent name HD /media/sdb1 and USB drive is sdc1 nothing will get over to sdc1 this i don't understand. or do it.?? Ok i try again. but this is strange.
AkkJaa...
I find out, i have 3 HDD in the debian box. so i disconnected 2 HDD then only system disk left. then now the USB drive is sdb1 so now it working to extract to the USB Drive.
I come back here after it is ready and have try it.
Thanks again.
AkkJaa...
Edited 2 time(s). Last edit at 01/28/2021 08:30AM by AkkJaa.
Yes but the USB drive is sdc1 and not sdb1 so how get it over to the USB drive.?? 2 diffrent name HD /media/sdb1 and USB drive is sdc1 nothing will get over to sdc1 this i don't understand. or do it.?? Ok i try again. but this is strange.
AkkJaa...
I find out, i have 3 HDD in the debian box. so i disconnected 2 HDD then only system disk left. then now the USB drive is sdb1 so now it working to extract to the USB Drive.
I come back here after it is ready and have try it.
Thanks again.
AkkJaa...
Edited 2 time(s). Last edit at 01/28/2021 08:30AM by AkkJaa.
|
Re: RN10400 January 28, 2021 02:07PM |
Registered: 3 years ago Posts: 116 |
Hi Bodhi,
Here is what i have done now.
The i move the USB drive to RN10400 motherboard and a new read out here.:-
Yes then you have it. I see there is something wrong yet but is seem's better now.
Ok thanks again.
Regards.
AkkJaa..
Here is what i have done now.
wipe /dev/sdb1 Okay to WIPE 1 special file ? (Yes/No) Yes Wiping /dev/sdb1, pass 1 (1 ) ^C 2009 / 945992] ETA 1d 19h *** Interrupted by signal 2 *** If you want to resume wiping while preserving the pass order, use these options: *** -X 1 -x 0,1,2,3,19,16,26,14,13,29,8,30,21,24,9,7,28,23,15,12,18,17,22,4,20,10,27,11,25,5,6,31,32,33,34 umount /media/sdb1 umount: /media/sdb1: not mounted. mkfs.ext3 -L rootfs /dev/sdb1 mke2fs 1.44.5 (15-Dec-2018) /dev/sdb1 is mounted; will not make a filesystem here! umount /media/sdb1 umount: /media/sdb1: not mounted. mkfs.ext3 -L rootfs /dev/sdb1 mke2fs 1.44.5 (15-Dec-2018) /dev/sdb1 is mounted; will not make a filesystem here! mkfs.ext3 -L rootfs /dev/sdb1 mke2fs 1.44.5 (15-Dec-2018) Creating filesystem with 3783968 4k blocks and 946560 inodes Filesystem UUID: 290c0f57-08b5-4f37-885d-3e7eec793f5b Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208 Allocating group tables: done Writing inode tables: done Creating journal (16384 blocks): done Writing superblocks and filesystem accounting information: done mount /dev/sdb1 /media/sdb1 cd /media/sdb1 tar -xjf Debian-5.2.9-mvebu-tld-1-rootfs-bodhi.tar.bz2 umount /media/sdb1 umount: /media/sdb1: not mounted.
The i move the USB drive to RN10400 motherboard and a new read out here.:-
Terminal ready
BootROM 1.08
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.4 (COM-PHY-V20)
Update PEX Device ID 0x6710
High speed PHY - Ended Successfully
0001
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run without PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:56:14) Marvell version: v2011.12 2014_T2.0p1
06/23/2015 ReadyNAS-104 V2.0
Board: DB-88F6710-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 200 [MHz]
DDR @ 600 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 512 MiB
Map: Code: 0x1feef000:0x1ff9f514
BSS: 0x1ffef8a0
Stack: 0x1f9eeef8
Heap: 0x1f9ef000:0x1feef000
NAND: (ID 0xf12c) 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Shutting down unused interfaces:
SDIO
AUDIO
TDM
Modules/Interfaces Detected:
RGMII0 Phy
RGMII1 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Net: egiga0, egiga1 [PRIME]
Power On!
FDT loaded successfully
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading /uImage-recovery
** Unable to read "/uImage-recovery" from usb 0:1 **
reading /initrd-recovery.gz
** Unable to read "/initrd-recovery.gz" from usb 0:1 **
NAND read: device 0 offset 0xd4000, size 0x6000
24576 bytes read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Marvell>> printenv
AC_Power_fail_detect=open
CASset=min
HW_version=MVT
MALLOC_len=5
Manufacturer=NETGEAR
Product=ReadyNAS 104
SKUNum=RN104
SerialNum=3EPE51EM006E2
Startup=Normal
UUID=8ad06a7e-97fc-11e4-9cf7-e8fcafe534ca
Version=V1.0
autoload=no
bootargs=console=ttyS0,115200
bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=usb start;fatload usb 0:1 0x2000000 /uImage-recovery;fatload usb 0:1 0x3000000 /initrd-recovery.gz;nand read 0x1000000 0xD4000 0x6000; bootm 0x2000000 0x3000000 0x1000000
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_ubi=ubi part ubifs; ubifsmount rootfs; ubifsload 0x2000000 kernel; ubifsload 0x3000000 initrd.gz; bootm 0x2000000 0x3000000 0x1000000
bootdelay=0
cacheShare=no
console=console=ttyS0,115200
disL2Cache=yes
disaMvPnp=no
eeeEnable=no
enaAutoRecovery=yes
enaClockGating=yes
enaExtDisk=no
enaFPU=no
enaMonExt=no
enaWrAllo=no
envver=3
eth1addr=E8:FC:AF:E5:34:CB
eth1mtu=1500
ethact=egiga1
ethaddr=E8:FC:AF:E5:34:CA
ethmtu=1500
ethprime=egiga1
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-370-db.dtb
image_name=uImage
initrd_name=uInitrd
load_addr=0x02000000
loadaddr=0x02000000
mtdids=nand0=armada-nand
mtdparts=mtdparts=armada-nand:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs)
mvNetConfig=mv_net_config=1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500
mv_pon_addr=00:50:43:00:00:02
nandEcc=1bit
netbsd_en=no
netretry=no
pcieTune=no
pexMode=rc
pxe_files_load=:default.arm-armada370-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
rcvrip=169.254.100.100
sata_delay_reset=0
sata_dma_mode=yes
setL2CacheWT=no
standalone=fsload $load_addr $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm $load_addr;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usb1Mode=host
usb2Mode=device
usbActive=0
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
Environment size: 2349/131068 bytes
Marvell>>
Yes then you have it. I see there is something wrong yet but is seem's better now.
Ok thanks again.
Regards.
AkkJaa..
|
Re: RN10400 January 28, 2021 04:15PM |
Admin Registered: 13 years ago Posts: 18,548 |
AkkJaa,
Let me show the difference between Windows, a full Linux distro with GUI, and a headless box with a basic rootfs like one I provided here.
- When we say "wipe the disk" we mean using fdisk to erase all partitions (sub command o inside fdisk).
- The USB drives or HDD drives are initialized by Linux with a drive letter at the /dev directory. So it is upto Linux to give the USB or HDD drives a device /dev/sda, /dev/sdb,....
- If there are partition on disk they will take /dev/sda1, /dev/sda2,...
- Usually the partitions will be mounted by Debian/Fedora/... GNU OS automatically in a full distribution. But not in the basic rootfs I released (it is a learning vehicle).
- To wipe and reformat, you need to unmount the USB partition(s). fdisk only works on a drive that has no mounted partition
- Depending on which device drive letter that Linux assigned to a drive, you would use that with fdisk. You would find out with dmesg (kernel logging) like this:
So if the USB drive is /dev/sdc, then
After you wipe with fdisk (sub command o), and created 1 partition (sub command n), and commit it (sub command w). Then exit fdisk and format the USB partition
Assuming the drive letter is /dev/sdc, the fist partition is /dev/sdc1
At this point the drive is still unmounted, so you need to mount it before writing
And then
========
The above is a really basic Linux chores, it is the same thing going on underneath Windows GUI, or Linux GUI. But here we use command line while being root because we deal with low-level stuff and need to be precise.
I understood transitioning from Windows to Linux GUI is easy, but the low level stuff is different, so often time you need to search for HOWTOs, or read the manual like:
so on :)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Let me show the difference between Windows, a full Linux distro with GUI, and a headless box with a basic rootfs like one I provided here.
- When we say "wipe the disk" we mean using fdisk to erase all partitions (sub command o inside fdisk).
- The USB drives or HDD drives are initialized by Linux with a drive letter at the /dev directory. So it is upto Linux to give the USB or HDD drives a device /dev/sda, /dev/sdb,....
- If there are partition on disk they will take /dev/sda1, /dev/sda2,...
- Usually the partitions will be mounted by Debian/Fedora/... GNU OS automatically in a full distribution. But not in the basic rootfs I released (it is a learning vehicle).
- To wipe and reformat, you need to unmount the USB partition(s). fdisk only works on a drive that has no mounted partition
- Depending on which device drive letter that Linux assigned to a drive, you would use that with fdisk. You would find out with dmesg (kernel logging) like this:
dmesg | grep USB(The last USB drive that was plugged in will show the activities at the end of dmesg)
So if the USB drive is /dev/sdc, then
fdisk /dev/sdc
After you wipe with fdisk (sub command o), and created 1 partition (sub command n), and commit it (sub command w). Then exit fdisk and format the USB partition
Assuming the drive letter is /dev/sdc, the fist partition is /dev/sdc1
mkfs.ext3 -L rootfs /dev/sdc1
At this point the drive is still unmounted, so you need to mount it before writing
mkdir /media/sdc1 mount /dev/sdc1 /media/sdc1
And then
cd /media/sdb1 tar -xjf Debian-5.2.9-mvebu-tld-1-rootfs-bodhi.tar.bz2 sync umount /media/sdc1
========
The above is a really basic Linux chores, it is the same thing going on underneath Windows GUI, or Linux GUI. But here we use command line while being root because we deal with low-level stuff and need to be precise.
I understood transitioning from Windows to Linux GUI is easy, but the low level stuff is different, so often time you need to search for HOWTOs, or read the manual like:
man fdisk man mkfs.ext3
so on :)
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: RN10400 January 28, 2021 05:04PM |
Registered: 3 years ago Posts: 116 |
Bodhi,
Yes i discover or find out about fdisk here now. i used fdisk much in dos before. so right now i have use the fdisk to remove 3 partition's on the USB drive. and formated the USB drive again with new partition and now i extrackt the files into the USB drive again. to see if that help.
And also about the HD and USB letters and how they change when i disconnect them.
I will try and see now. i see the USB are ready now so i will try it in the motherboard again and see what happend now.
ok. thanks again.
AkkJaa...
Yes i discover or find out about fdisk here now. i used fdisk much in dos before. so right now i have use the fdisk to remove 3 partition's on the USB drive. and formated the USB drive again with new partition and now i extrackt the files into the USB drive again. to see if that help.
And also about the HD and USB letters and how they change when i disconnect them.
I will try and see now. i see the USB are ready now so i will try it in the motherboard again and see what happend now.
ok. thanks again.
AkkJaa...
|
Re: RN10400 January 28, 2021 05:24PM |
Registered: 3 years ago Posts: 116 |
Bodhi,
This is the last i try'ed with the USB drive.
Regards
AkkJaa...
This is the last i try'ed with the USB drive.
Terminal ready
BootROM 1.08
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.4 (COM-PHY-V20)
Update PEX Device ID 0x6710
High speed PHY - Ended Successfully
0001
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run without PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:56:14) Marvell version: v2011.12 2014_T2.0p1
06/23/2015 ReadyNAS-104 V2.0
Board: DB-88F6710-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 200 [MHz]
DDR @ 600 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 512 MiB
Port0: phyAddr=0x0, Not Marvell PHY id1 ffff id2 ffff
PHY error - shutdown port0
Map: Code: 0x1feef000:0x1ff9f514
BSS: 0x1ffef8a0
Stack: 0x1f9eeef8
Heap: 0x1f9ef000:0x1feef000
NAND: (ID 0xf12c) 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Shutting down unused interfaces:
SDIO
AUDIO
TDM
Modules/Interfaces Detected:
RGMII0 Phy
RGMII1 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Net: egiga1 [PRIME]
Warning: egiga1 MAC addresses don't match:
Address in SROM is e8:fc:af:e5:34:cb
Address in environment is e8:fc:af:e5:34:ca
Power On!
FDT loaded successfully
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading /uImage-recovery
** Unable to read "/uImage-recovery" from usb 0:1 **
reading /initrd-recovery.gz
** Unable to read "/initrd-recovery.gz" from usb 0:1 **
NAND read: device 0 offset 0xd4000, size 0x6000
24576 bytes read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Marvell>> printenv
AC_Power_fail_detect=open
CASset=min
HW_version=MVT
MALLOC_len=5
Manufacturer=NETGEAR
Product=ReadyNAS 104
SKUNum=RN104
SerialNum=3EPE51EM006E2
Startup=Normal
UUID=8ad06a7e-97fc-11e4-9cf7-e8fcafe534ca
Version=V1.0
autoload=no
bootargs=console=ttyS0,115200
bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=usb start;fatload usb 0:1 0x2000000 /uImage-recovery;fatload usb 0:1 0x3000000 /initrd-recovery.gz;nand read 0x1000000 0xD4000 0x6000; bootm 0x2000000 0x3000000 0x1000000
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_ubi=ubi part ubifs; ubifsmount rootfs; ubifsload 0x2000000 kernel; ubifsload 0x3000000 initrd.gz; bootm 0x2000000 0x3000000 0x1000000
bootdelay=0
cacheShare=no
console=console=ttyS0,115200
disL2Cache=yes
disaMvPnp=no
eeeEnable=no
enaAutoRecovery=yes
enaClockGating=yes
enaExtDisk=no
enaFPU=no
enaMonExt=no
enaWrAllo=no
envver=3
eth1addr=E8:FC:AF:E5:34:CB
eth1mtu=1500
ethact=egiga1
ethaddr=E8:FC:AF:E5:34:CA
ethmtu=1500
ethprime=egiga1
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-370-db.dtb
image_name=uImage
initrd_name=uInitrd
load_addr=0x02000000
loadaddr=0x02000000
mtdids=nand0=armada-nand
mtdparts=mtdparts=armada-nand:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs)
mvNetConfig=mv_net_config=1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500
mv_pon_addr=00:50:43:00:00:02
nandEcc=1bit
netbsd_en=no
netretry=no
pcieTune=no
pexMode=rc
pxe_files_load=:default.arm-armada370-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
rcvrip=169.254.100.100
sata_delay_reset=0
sata_dma_mode=yes
setL2CacheWT=no
standalone=fsload $load_addr $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm $load_addr;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usb1Mode=host
usb2Mode=device
usbActive=0
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
Environment size: 2349/131068 bytes
Marvell>>
I wil try again later on.
Regards
AkkJaa...
|
Re: RN10400 January 28, 2021 05:43PM |
Registered: 3 years ago Posts: 116 |
Hi Bodhi,
Here is from this command
Yes. ok i think i understand. alittle bit like very old dos but different ofcause.
AkkJaa...
Here is from this command
dmesg | grep USB [ 3.207419] ACPI: bus type USB registered [ 3.257036] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.287683] ehci-pci 0000:00:10.4: new USB bus registered, assigned bus number 1 [ 3.301180] ehci-pci 0000:00:10.4: USB 2.0 started, EHCI 1.00 [ 3.301356] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 [ 3.301359] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.301685] hub 1-0:1.0: USB hub found [ 3.314329] uhci_hcd: USB Universal Host Controller Interface driver [ 3.314706] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2 [ 3.314905] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 [ 3.314908] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.315181] hub 2-0:1.0: USB hub found [ 3.328848] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3 [ 3.336542] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 [ 3.336547] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.336921] hub 3-0:1.0: USB hub found [ 3.337375] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4 [ 3.337554] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 [ 3.337557] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.344248] hub 4-0:1.0: USB hub found [ 3.368222] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5 [ 3.368404] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 [ 3.368407] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.368695] hub 5-0:1.0: USB hub found [ 806.227668] usb 1-5: new high-speed USB device number 2 using ehci-pci [ 806.389554] usb 1-5: New USB device found, idVendor=13fe, idProduct=4300, bcdDevice= 1.00 [ 806.389561] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 806.389563] usb 1-5: Product: USB DISK 2.0 [ 806.628332] usb-storage 1-5:1.0: USB Mass Storage device detected [ 808.468741] scsi 4:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 4 [ 5245.531073] usb 1-5: USB disconnect, device number 2 [ 5269.940274] usb 3-2: new full-speed USB device number 2 using uhci_hcd [ 5270.156308] usb 3-2: New USB device found, idVendor=10c4, idProduct=ea60, bcdDevice= 1.00 [ 5270.156315] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 5270.156318] usb 3-2: Product: CP2102 USB to UART Bridge Controller [ 5270.361391] usbserial: USB Serial support registered for generic [ 5270.390829] usbserial: USB Serial support registered for cp210x [ 5270.400536] usb 3-2: cp210x converter now attached to ttyUSB0 [ 5651.165417] usb 1-5: new high-speed USB device number 4 using ehci-pci [ 5651.327398] usb 1-5: New USB device found, idVendor=13fe, idProduct=4300, bcdDevice= 1.00 [ 5651.327404] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 5651.327406] usb 1-5: Product: USB DISK 2.0 [ 5651.333614] usb-storage 1-5:1.0: USB Mass Storage device detected [ 5653.179808] scsi 4:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 4 [ 6881.428960] usb 3-2: USB disconnect, device number 2 [ 6881.429388] cp210x ttyUSB0: cp210x converter now disconnected from ttyUSB0 [12940.280373] usb 1-5: USB disconnect, device number 4 [12952.924901] usb 1-5: new high-speed USB device number 5 using ehci-pci [12953.090974] usb 1-5: New USB device found, idVendor=13fe, idProduct=4300, bcdDevice= 1.00 [12953.090982] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [12953.090984] usb 1-5: Product: USB DISK 2.0 [12953.095461] usb-storage 1-5:1.0: USB Mass Storage device detected [12954.827377] scsi 4:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 4 [15626.628114] usb 1-5: USB disconnect, device number 5 [15810.428014] usb 1-5: new high-speed USB device number 6 using ehci-pci [15810.585967] usb 1-5: New USB device found, idVendor=13fe, idProduct=4300, bcdDevice= 1.00 [15810.585973] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [15810.585975] usb 1-5: Product: USB DISK 2.0 [15810.592385] usb-storage 1-5:1.0: USB Mass Storage device detected [15812.595671] scsi 4:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 4 [19096.837442] usb 3-2: new full-speed USB device number 3 using uhci_hcd [19097.053479] usb 3-2: New USB device found, idVendor=10c4, idProduct=ea60, bcdDevice= 1.00 [19097.053487] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [19097.053490] usb 3-2: Product: CP2102 USB to UART Bridge Controller [19097.070717] usb 3-2: cp210x converter now attached to ttyUSB0 [19097.634406] usb 1-5: USB disconnect, device number 6 [24915.997157] usb 1-5: new high-speed USB device number 8 using ehci-pci [24916.163211] usb 1-5: New USB device found, idVendor=13fe, idProduct=4300, bcdDevice= 1.00 [24916.163218] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [24916.163221] usb 1-5: Product: USB DISK 2.0 [24916.169395] usb-storage 1-5:1.0: USB Mass Storage device detected [24918.017878] scsi 4:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 4 [26914.166170] usb 1-5: USB disconnect, device number 8 [26924.671323] usb 1-5: new high-speed USB device number 9 using ehci-pci [26924.833446] usb 1-5: New USB device found, idVendor=13fe, idProduct=4300, bcdDevice= 1.00 [26924.833456] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [26924.833459] usb 1-5: Product: USB DISK 2.0 [26924.839969] usb-storage 1-5:1.0: USB Mass Storage device detected [26926.870395] scsi 4:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 4 [27309.307663] usb 1-5: USB disconnect, device number 9 [27424.537832] usb 1-5: new high-speed USB device number 10 using ehci-pci [27424.695892] usb 1-5: New USB device found, idVendor=13fe, idProduct=4300, bcdDevice= 1.00 [27424.695900] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [27424.695902] usb 1-5: Product: USB DISK 2.0 [27424.702545] usb-storage 1-5:1.0: USB Mass Storage device detected [27426.440666] scsi 4:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 4 [28040.307699] usb 1-5: USB disconnect, device number 10 [28043.257690] usb 1-6: new high-speed USB device number 11 using ehci-pci [28043.423807] usb 1-6: New USB device found, idVendor=13fe, idProduct=4300, bcdDevice= 1.00 [28043.423814] usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [28043.423817] usb 1-6: Product: USB DISK 2.0 [28043.430328] usb-storage 1-6:1.0: USB Mass Storage device detected [28044.980570] scsi 4:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 4 [28119.963793] usb 1-6: USB disconnect, device number 11 [28122.703651] usb 1-5: new high-speed USB device number 12 using ehci-pci [28122.873292] usb 1-5: New USB device found, idVendor=13fe, idProduct=4300, bcdDevice= 1.00 [28122.873298] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [28122.873301] usb 1-5: Product: USB DISK 2.0 [28122.875536] usb-storage 1-5:1.0: USB Mass Storage device detected [28124.438433] scsi 4:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 4 [33859.447349] usb 1-5: USB disconnect, device number 12 [33936.991889] usb 1-5: new high-speed USB device number 13 using ehci-pci [33937.157955] usb 1-5: New USB device found, idVendor=13fe, idProduct=4300, bcdDevice= 1.00 [33937.157965] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [33937.157967] usb 1-5: Product: USB DISK 2.0 [33937.163465] usb-storage 1-5:1.0: USB Mass Storage device detected [33939.087527] scsi 4:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 4 [34129.511973] usb 1-5: USB disconnect, device number 13 [35113.765105] usb 1-5: new high-speed USB device number 14 using ehci-pci [35113.927192] usb 1-5: New USB device found, idVendor=13fe, idProduct=4300, bcdDevice= 1.00 [35113.927199] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [35113.927201] usb 1-5: Product: USB DISK 2.0 [35113.933327] usb-storage 1-5:1.0: USB Mass Storage device detected [35115.755184] scsi 4:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 4
Yes. ok i think i understand. alittle bit like very old dos but different ofcause.
AkkJaa...
|
Re: RN10400 January 28, 2021 09:10PM |
Admin Registered: 13 years ago Posts: 18,548 |
AkkJaa,
- Plug in the USB rootfs with Debian-5.2.9-mvebu-tld-1-rootfs-bodhi.tar.bz2.
- Power up, interrupt serial console and
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 01/28/2021 09:10PM by bodhi.
- Plug in the USB rootfs with Debian-5.2.9-mvebu-tld-1-rootfs-bodhi.tar.bz2.
- Power up, interrupt serial console and
setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial' setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage' setenv load_uinitrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd' setenv usb_boot 'mw 0x800000 0 1; run load_uimage; if run load_uinitrd; then bootm 0x800000 0x2100000; else bootm 0x800000; fi' setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot' setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset'And then,
printenv boot
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Edited 1 time(s). Last edit at 01/28/2021 09:10PM by bodhi.
|
Re: RN10400 January 30, 2021 03:08AM |
Registered: 3 years ago Posts: 116 |
Bodhi
Now i have try it here is the out put.
Yes, i will try 1 more time and interrupt faster.
Thanks.
AkkJaa..
Now i have try it here is the out put.
Terminal ready
BootROM 1.08
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.4 (COM-PHY-V20)
Update PEX Device ID 0x6710
High speed PHY - Ended Successfully
0001
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run without PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:56:14) Marvell version: v2011.12 2014_T2.0p1
06/23/2015 ReadyNAS-104 V2.0
Board: DB-88F6710-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 200 [MHz]
DDR @ 600 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 512 MiB
Port0: phyAddr=0x0, Not Marvell PHY id1 ffff id2 ffff
PHY error - shutdown port0
Map: Code: 0x1feef000:0x1ff9f514
BSS: 0x1ffef8a0
Stack: 0x1f9eeef8
Heap: 0x1f9ef000:0x1feef000
NAND: (ID 0xf12c) 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Shutting down unused interfaces:
SDIO
AUDIO
TDM
Modules/Interfaces Detected:
RGMII0 Phy
RGMII1 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Net: egiga1 [PRIME]
Warning: egiga1 MAC addresses don't match:
Address in SROM is e8:fc:af:e5:34:cb
Address in environment is e8:fc:af:e5:34:ca
Power On!
FDT loaded successfully
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading /uImage-recovery
** Unable to read "/uImage-recovery" from usb 0:1 **
reading /initrd-recovery.gz
** Unable to read "/initrd-recovery.gz" from usb 0:1 **
NAND read: device 0 offset 0xd4000, size 0x6000
24576 bytes read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Marvell>> <INTERRUPT>
Marvell>> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial'
Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
Marvell>> setenv load_uinitrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd'
Marvell>> setenv usb_boot 'mw 0x800000 0 1; run load_uimage; if run load_uinitrd; then bootm 0x800000 0x2100000; else bootm 0x800000; fi'
Marvell>> setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot'
Marvell>> setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset'
Marvell>> printenv
AC_Power_fail_detect=open
CASset=min
HW_version=MVT
MALLOC_len=5
Manufacturer=NETGEAR
Product=ReadyNAS 104
SKUNum=RN104
SerialNum=3EPE51EM006E2
Startup=Normal
UUID=8ad06a7e-97fc-11e4-9cf7-e8fcafe534ca
Version=V1.0
autoload=no
bootargs=console=ttyS0,115200
bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=usb start; run usb_bootcmd; usb stop; reset
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_ubi=ubi part ubifs; ubifsmount rootfs; ubifsload 0x2000000 kernel; ubifsload 0x3000000 initrd.gz; bootm 0x2000000 0x3000000 0x1000000
bootdelay=0
cacheShare=no
console=console=ttyS0,115200
disL2Cache=yes
disaMvPnp=no
eeeEnable=no
enaAutoRecovery=yes
enaClockGating=yes
enaExtDisk=no
enaFPU=no
enaMonExt=no
enaWrAllo=no
envver=3
eth1addr=E8:FC:AF:E5:34:CB
eth1mtu=1500
ethact=egiga1
ethaddr=E8:FC:AF:E5:34:CA
ethmtu=1500
ethprime=egiga1
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-370-db.dtb
image_name=uImage
initrd_name=uInitrd
load_addr=0x02000000
load_uimage=ext2load usb 0:1 0x800000 /boot/uImage
load_uinitrd=ext2load usb 0:1 0x2100000 /boot/uInitrd
loadaddr=0x02000000
mtdids=nand0=armada-nand
mtdparts=mtdparts=armada-nand:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs)
mvNetConfig=mv_net_config=1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500
mv_pon_addr=00:50:43:00:00:02
nandEcc=1bit
netbsd_en=no
netretry=no
pcieTune=no
pexMode=rc
pxe_files_load=:default.arm-armada370-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
rcvrip=169.254.100.100
sata_delay_reset=0
sata_dma_mode=yes
setL2CacheWT=no
standalone=fsload $load_addr $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm $load_addr;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usb1Mode=host
usb2Mode=device
usbActive=0
usb_boot=mw 0x800000 0 1; run load_uimage; if run load_uinitrd; then bootm 0x800000 0x2100000; else bootm 0x800000; fi
usb_bootcmd=run usb_set_bootargs; run usb_boot
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
Environment size: 2607/131068 bytes
Marvell>> boot
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
** File not found /boot/uImage
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
9488618 bytes read
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
resetting ...
BootROM 1.08
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.4 (COM-PHY-V20)
Update PEX Device ID 0x6710
High speed PHY - Ended Successfully
0000
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run without PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:56:14) Marvell version: v2011.12 2014_T2.0p1
06/23/2015 ReadyNAS-104 V2.0
Board: DB-88F6710-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 200 [MHz]
DDR @ 600 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 512 MiB
Port0: phyAddr=0x0, Not Marvell PHY id1 ffff id2 ffff
PHY error - shutdown port0
Map: Code: 0x1feef000:0x1ff9f514
BSS: 0x1ffef8a0
Stack: 0x1f9eeef8
Heap: 0x1f9ef000:0x1feef000
NAND: (ID 0xf12c) 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Shutting down unused interfaces:
SDIO
AUDIO
TDM
Modules/Interfaces Detected:
RGMII0 Phy
RGMII1 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Net: egiga1 [PRIME]
Warning: egiga1 MAC addresses don't match:
Address in SROM is e8:fc:af:e5:34:cb
Address in environment is e8:fc:af:e5:34:ca
Power On!
FDT loaded successfully
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading /uImage-recovery
** Unable to read "/uImage-recovery" from usb 0:1 **
reading /initrd-recovery.gz
** Unable to read "/initrd-recovery.gz" from usb 0:1 **
NAND read: device 0 offset 0xd4000, size 0x6000
24576 bytes read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Marvell>>
Yes, i will try 1 more time and interrupt faster.
Thanks.
AkkJaa..
|
Re: RN10400 January 30, 2021 03:22AM |
Registered: 3 years ago Posts: 116 |
Bodhi,
This is reading 2 and i interrupt alittlebit faster.
Ok i think it is the same, but it go alittlebit longer to boot up. but that was the same in the first one to.
Thanks again.
AkkJaa...
This is reading 2 and i interrupt alittlebit faster.
Terminal ready
BootROM 1.08
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.4 (COM-PHY-V20)
Update PEX Device ID 0x6710
High speed PHY - Ended Successfully
0001
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run without PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:56:14) Marvell version: v2011.12 2014_T2.0p1
06/23/2015 ReadyNAS-104 V2.0
Board: DB-88F6710-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 200 [MHz]
DDR @ 600 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 512 MiB
Map: Code: 0x1feef000:0x1ff9f514
BSS: 0x1ffef8a0
Stack: 0x1f9eeef8
Heap: 0x1f9ef000:0x1feef000
NAND: (ID 0xf12c) 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Shutting down unused interfaces:
SDIO
AUDIO
TDM
Modules/Interfaces Detected:
RGMII0 Phy
RGMII1 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Net: egiga0, egiga1 [PRIME]
Power On!
FDT loaded successfully
Hit any key to stop autoboot: 0
Marvell>> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial'
Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
Marvell>> setenv load_uinitrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd'
Marvell>> setenv usb_boot 'mw 0x800000 0 1; run load_uimage; if run load_uinitrd; then bootm 0x800000 0x2100000; else bootm 0x800000; fi'
Marvell>> setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot'
Marvell>> setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset'
Marvell>> printenv
AC_Power_fail_detect=open
CASset=min
HW_version=MVT
MALLOC_len=5
Manufacturer=NETGEAR
Product=ReadyNAS 104
SKUNum=RN104
SerialNum=3EPE51EM006E2
Startup=Normal
UUID=8ad06a7e-97fc-11e4-9cf7-e8fcafe534ca
Version=V1.0
autoload=no
bootargs=console=ttyS0,115200
bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=usb start; run usb_bootcmd; usb stop; reset
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_ubi=ubi part ubifs; ubifsmount rootfs; ubifsload 0x2000000 kernel; ubifsload 0x3000000 initrd.gz; bootm 0x2000000 0x3000000 0x1000000
bootdelay=0
cacheShare=no
console=console=ttyS0,115200
disL2Cache=yes
disaMvPnp=no
eeeEnable=no
enaAutoRecovery=yes
enaClockGating=yes
enaExtDisk=no
enaFPU=no
enaMonExt=no
enaWrAllo=no
envver=3
eth1addr=E8:FC:AF:E5:34:CB
eth1mtu=1500
ethact=egiga1
ethaddr=E8:FC:AF:E5:34:CA
ethmtu=1500
ethprime=egiga1
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-370-db.dtb
image_name=uImage
initrd_name=uInitrd
load_addr=0x02000000
load_uimage=ext2load usb 0:1 0x800000 /boot/uImage
load_uinitrd=ext2load usb 0:1 0x2100000 /boot/uInitrd
loadaddr=0x02000000
mtdids=nand0=armada-nand
mtdparts=mtdparts=armada-nand:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs)
mvNetConfig=mv_net_config=1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500
mv_pon_addr=00:50:43:00:00:02
nandEcc=1bit
netbsd_en=no
netretry=no
pcieTune=no
pexMode=rc
pxe_files_load=:default.arm-armada370-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
rcvrip=169.254.100.100
sata_delay_reset=0
sata_dma_mode=yes
setL2CacheWT=no
standalone=fsload $load_addr $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm $load_addr;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usb1Mode=host
usb2Mode=device
usbActive=0
usb_boot=mw 0x800000 0 1; run load_uimage; if run load_uinitrd; then bootm 0x800000 0x2100000; else bootm 0x800000; fi
usb_bootcmd=run usb_set_bootargs; run usb_boot
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
Environment size: 2607/131068 bytes
Marvell>> boot
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
** File not found /boot/uImage
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
9488618 bytes read
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
resetting ...
BootROM 1.08
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.4 (COM-PHY-V20)
Update PEX Device ID 0x6710
High speed PHY - Ended Successfully
0000
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run without PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:56:14) Marvell version: v2011.12 2014_T2.0p1
06/23/2015 ReadyNAS-104 V2.0
Board: DB-88F6710-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 200 [MHz]
DDR @ 600 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 512 MiB
Map: Code: 0x1feef000:0x1ff9f514
BSS: 0x1ffef8a0
Stack: 0x1f9eeef8
Heap: 0x1f9ef000:0x1feef000
NAND: (ID 0xf12c) 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Shutting down unused interfaces:
SDIO
AUDIO
TDM
Modules/Interfaces Detected:
RGMII0 Phy
RGMII1 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Net: egiga0, egiga1 [PRIME]
Power On!
FDT loaded successfully
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading /uImage-recovery
** Unable to read "/uImage-recovery" from usb 0:1 **
reading /initrd-recovery.gz
** Unable to read "/initrd-recovery.gz" from usb 0:1 **
NAND read: device 0 offset 0xd4000, size 0x6000
24576 bytes read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Marvell>>
Ok i think it is the same, but it go alittlebit longer to boot up. but that was the same in the first one to.
Thanks again.
AkkJaa...
|
Re: RN10400 January 30, 2021 03:44PM |
Admin Registered: 13 years ago Posts: 18,548 |
AkkJaa,
The rootfs was not prepared correctly
Mount this on you Linux desktop/laptop and assuming it is mounted at /media/sdc1
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
The rootfs was not prepared correctly
Loading file "/boot/uImage" from usb device 0:1 (usbda1) ** File not found /boot/uImage
Mount this on you Linux desktop/laptop and assuming it is mounted at /media/sdc1
free -h mount ls -lart /media/sdc1/boot
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: RN10400 January 30, 2021 07:19PM |
Registered: 3 years ago Posts: 116 |
Bodhi
Here is the read out.
Yes there is the dir sdb1 but it is empty only the Debian-5.2.9-mvebu-tld-1-rootfs-bodhi.tar.bz2 is in the dir. /media/sdb1
And everything is in the USB Drive
But i now run on a laptop computer a lenovo B470 with 1 TB HD and 4 Gb ram. with intel Core i3. and i have deleted everything on the USB drive again with fdisk then format with
Thanks again.
AkkJaa...
Here is the read out.
free -h
total used free shared buff/cache available
Mem: 3.8Gi 810Mi 1.1Gi 186Mi 1.9Gi 2.5Gi
Swap: 3.9Gi 0B 3.9Gi
mount
sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,relatime)
proc on /proc type proc (rw,nosuid,nodev,noexec,relatime)
udev on /dev type devtmpfs (rw,nosuid,relatime,size=1972516k,nr_inodes=184834,mode=755)
devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000)
tmpfs on /run type tmpfs (rw,nosuid,noexec,relatime,size=397660k,mode=755)
/dev/sda6 on / type ext4 (rw,relatime,errors=remount-ro)
securityfs on /sys/kernel/security type securityfs (rw,nosuid,nodev,noexec,relatime)
tmpfs on /dev/shm type tmpfs (rw,nosuid,nodev)
tmpfs on /run/lock type tmpfs (rw,nosuid,nodev,noexec,relatime,size=5120k)
tmpfs on /sys/fs/cgroup type tmpfs (ro,nosuid,nodev,noexec,mode=755)
cgroup2 on /sys/fs/cgroup/unified type cgroup2 (rw,nosuid,nodev,noexec,relatime,nsdelegate)
cgroup on /sys/fs/cgroup/systemd type cgroup (rw,nosuid,nodev,noexec,relatime,xattr,name=systemd)
pstore on /sys/fs/pstore type pstore (rw,nosuid,nodev,noexec,relatime)
bpf on /sys/fs/bpf type bpf (rw,nosuid,nodev,noexec,relatime,mode=700)
cgroup on /sys/fs/cgroup/pids type cgroup (rw,nosuid,nodev,noexec,relatime,pids)
cgroup on /sys/fs/cgroup/rdma type cgroup (rw,nosuid,nodev,noexec,relatime,rdma)
cgroup on /sys/fs/cgroup/cpuset type cgroup (rw,nosuid,nodev,noexec,relatime,cpuset)
cgroup on /sys/fs/cgroup/devices type cgroup (rw,nosuid,nodev,noexec,relatime,devices)
cgroup on /sys/fs/cgroup/cpu,cpuacct type cgroup (rw,nosuid,nodev,noexec,relatime,cpu,cpuacct)
cgroup on /sys/fs/cgroup/net_cls,net_prio type cgroup (rw,nosuid,nodev,noexec,relatime,net_cls,net_prio)
cgroup on /sys/fs/cgroup/freezer type cgroup (rw,nosuid,nodev,noexec,relatime,freezer)
cgroup on /sys/fs/cgroup/blkio type cgroup (rw,nosuid,nodev,noexec,relatime,blkio)
cgroup on /sys/fs/cgroup/memory type cgroup (rw,nosuid,nodev,noexec,relatime,memory)
cgroup on /sys/fs/cgroup/perf_event type cgroup (rw,nosuid,nodev,noexec,relatime,perf_event)
systemd-1 on /proc/sys/fs/binfmt_misc type autofs (rw,relatime,fd=27,pgrp=1,timeout=0,minproto=5,maxproto=5,direct,pipe_ino=13539)
hugetlbfs on /dev/hugepages type hugetlbfs (rw,relatime,pagesize=2M)
mqueue on /dev/mqueue type mqueue (rw,relatime)
debugfs on /sys/kernel/debug type debugfs (rw,relatime)
fusectl on /sys/fs/fuse/connections type fusectl (rw,relatime)
tmpfs on /run/user/0 type tmpfs (rw,nosuid,nodev,relatime,size=397656k,mode=700)
gvfsd-fuse on /run/user/0/gvfs type fuse.gvfsd-fuse (rw,nosuid,nodev,relatime,user_id=0,group_id=0)
/dev/sdb1 on /media/root/rootfs type ext3 (rw,nosuid,nodev,relatime,uhelper=udisks2)
ls -lart /media/sdc1/boot
ls: cannot access '/media/sdc1/boot': No such file or directory
ls -lart /media/sdb1/boot
ls: cannot access '/media/sdb1/boot': No such file or directory
Yes there is the dir sdb1 but it is empty only the Debian-5.2.9-mvebu-tld-1-rootfs-bodhi.tar.bz2 is in the dir. /media/sdb1
And everything is in the USB Drive
But i now run on a laptop computer a lenovo B470 with 1 TB HD and 4 Gb ram. with intel Core i3. and i have deleted everything on the USB drive again with fdisk then format with
mkfs.ext3 -L rootfs /dev/sdb1and have run the install again
cd /media/sdb1 tar -xjf Debian-5.2.9-mvebu-tld-1-rootfs-bodhi.tar.bz2then
syncand
cd / umount /media/sdb1Then when done move USB drive to RN10400 and start up and it is the same. So i don't know what is wrong.
Thanks again.
AkkJaa...
|
Re: RN10400 January 30, 2021 09:04PM |
Admin Registered: 13 years ago Posts: 18,548 |
AkkJaa,
Again :) it is not mounted yet! you have to mount it first.
and then
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Again :) it is not mounted yet! you have to mount it first.
mkdir -p /media/sdb1 mount /dev/sdb1 /media/sdb1
and then
ls -lart /media/sdb1/boot
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: RN10400 January 31, 2021 03:53AM |
Registered: 3 years ago Posts: 116 |
Hi Bodhi,
I think i have done somthing wrong but now i have run fdisk and delete the partion and make a new one. But will it be a pri or ext partition.? when i make it in the Fdisk. on this readout i have make a pri partion.
But i make all new with a pri partition and it is the same Error as before. but now i got this read out now.
Yes but this is when i make the USB drive as a pri partition in fdisk. maybe i must make it ext partition in fdisk. or that maybe come when i format with Ext3 later on.?
Ok what do you think.
Many thanks again.
AkkJaa..
Ps. i have some problem with this but i love it, i really start to like this debian linux things.
I think i have done somthing wrong but now i have run fdisk and delete the partion and make a new one. But will it be a pri or ext partition.? when i make it in the Fdisk. on this readout i have make a pri partion.
But i make all new with a pri partition and it is the same Error as before. but now i got this read out now.
free -h
total used free shared buff/cache available
Mem: 3.8Gi 755Mi 1.1Gi 186Mi 1.9Gi 2.5Gi
Swap: 3.9Gi 0.0Ki 3.9Gi
Then Next command
mount sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,relatime) proc on /proc type proc (rw,nosuid,nodev,noexec,relatime) udev on /dev type devtmpfs (rw,nosuid,relatime,size=1972484k,nr_inodes=184818,mode=755) devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000) tmpfs on /run type tmpfs (rw,nosuid,noexec,relatime,size=397652k,mode=755) /dev/sda6 on / type ext4 (rw,relatime,errors=remount-ro) securityfs on /sys/kernel/security type securityfs (rw,nosuid,nodev,noexec,relatime) tmpfs on /dev/shm type tmpfs (rw,nosuid,nodev) tmpfs on /run/lock type tmpfs (rw,nosuid,nodev,noexec,relatime,size=5120k) tmpfs on /sys/fs/cgroup type tmpfs (ro,nosuid,nodev,noexec,mode=755) cgroup2 on /sys/fs/cgroup/unified type cgroup2 (rw,nosuid,nodev,noexec,relatime,nsdelegate) cgroup on /sys/fs/cgroup/systemd type cgroup (rw,nosuid,nodev,noexec,relatime,xattr,name=systemd) pstore on /sys/fs/pstore type pstore (rw,nosuid,nodev,noexec,relatime) bpf on /sys/fs/bpf type bpf (rw,nosuid,nodev,noexec,relatime,mode=700) cgroup on /sys/fs/cgroup/perf_event type cgroup (rw,nosuid,nodev,noexec,relatime,perf_event) cgroup on /sys/fs/cgroup/cpu,cpuacct type cgroup (rw,nosuid,nodev,noexec,relatime,cpu,cpuacct) cgroup on /sys/fs/cgroup/rdma type cgroup (rw,nosuid,nodev,noexec,relatime,rdma) cgroup on /sys/fs/cgroup/cpuset type cgroup (rw,nosuid,nodev,noexec,relatime,cpuset) cgroup on /sys/fs/cgroup/blkio type cgroup (rw,nosuid,nodev,noexec,relatime,blkio) cgroup on /sys/fs/cgroup/pids type cgroup (rw,nosuid,nodev,noexec,relatime,pids) cgroup on /sys/fs/cgroup/freezer type cgroup (rw,nosuid,nodev,noexec,relatime,freezer) cgroup on /sys/fs/cgroup/net_cls,net_prio type cgroup (rw,nosuid,nodev,noexec,relatime,net_cls,net_prio) cgroup on /sys/fs/cgroup/memory type cgroup (rw,nosuid,nodev,noexec,relatime,memory) cgroup on /sys/fs/cgroup/devices type cgroup (rw,nosuid,nodev,noexec,relatime,devices) systemd-1 on /proc/sys/fs/binfmt_misc type autofs (rw,relatime,fd=25,pgrp=1,timeout=0,minproto=5,maxproto=5,direct,pipe_ino=11763) mqueue on /dev/mqueue type mqueue (rw,relatime) hugetlbfs on /dev/hugepages type hugetlbfs (rw,relatime,pagesize=2M) debugfs on /sys/kernel/debug type debugfs (rw,relatime) fusectl on /sys/fs/fuse/connections type fusectl (rw,relatime) tmpfs on /run/user/0 type tmpfs (rw,nosuid,nodev,relatime,size=397648k,mode=700) gvfsd-fuse on /run/user/0/gvfs type fuse.gvfsd-fuse (rw,nosuid,nodev,relatime,user_id=0,group_id=0) /dev/sda1 on /media/root/6979e70a-644f-45b0-9dcb-a83bbfcc3ae6 type ext4 (rw,nosuid,nodev,relatime,uhelper=udisks2) /dev/sdb1 on /media/root/rootfs type ext3 (rw,nosuid,nodev,relatime,uhelper=udisks2)Then the last command.
ls -lart /media/sdb1/boot total 46192 drwxrwxrwx 21 root root 4096 Jan 20 2017 .. -rwxr-xr-x 1 root root 5057632 Aug 19 2019 zImage-5.2.9-mvebu-tld-1 -rwxr-xr-x 1 root root 5057632 Aug 19 2019 zImage -rw-r--r-- 1 root root 183639 Aug 19 2019 config-5.2.9-mvebu-tld-1 -rw------- 1 root root 5057632 Aug 19 2019 vmlinuz-5.2.9-mvebu-tld-1 -rw------- 1 root root 3266081 Aug 19 2019 System.map-5.2.9-mvebu-tld-1 -rw-r--r-- 1 root root 9676808 Aug 19 2019 linux-headers-5.2.9-mvebu-tld-1_1.0_armhf.deb drwxr-xr-x 2 root root 4096 Aug 19 2019 dts -rw-r--r-- 1 root root 9488554 Aug 26 2019 initrd.img-5.2.9-mvebu-tld-1 -rw-r--r-- 1 root root 9488618 Aug 26 2019 uInitrd drwxr-xr-x 3 root root 4096 Sep 5 2019 .
Yes but this is when i make the USB drive as a pri partition in fdisk. maybe i must make it ext partition in fdisk. or that maybe come when i format with Ext3 later on.?
Ok what do you think.
Many thanks again.
AkkJaa..
Ps. i have some problem with this but i love it, i really start to like this debian linux things.
|
Re: RN10400 January 31, 2021 09:35AM |
Registered: 3 years ago Posts: 116 |
Bodhi,
Now i have delete it again with fdisk. Then make a new ext partision with fdisk. then format with.
And her is when i interrupt.
Yes then you have it. And here come the other read out.
Next one.
Yes then i have done it with pri partition and now the last time with ext partition and all look the same.
Thanks again.
Best regards.
AkkJaa...
Now i have delete it again with fdisk. Then make a new ext partision with fdisk. then format with.
mkfs.ext3 -L rootfs /dev/sdb1Then make dir
mkdir /media/sdb1 mount /dev/sdb1 /media/sdb1And then
cd /media/stb1 tar -xjf Debian-5.2.9-mvebu-tld-1-rootfs-bodhi.tar.bz2And
syncand then
cd / umount /media/sdb1then i move USB drive to NR10400
picocom --b 115200 --f n --p n --d 8 /dev/ttyUSB0Here is the read out
Terminal ready
BootROM 1.08
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.4 (COM-PHY-V20)
Update PEX Device ID 0x6710
High speed PHY - Ended Successfully
0001
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run without PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:56:14) Marvell version: v2011.12 2014_T2.0p1
06/23/2015 ReadyNAS-104 V2.0
Board: DB-88F6710-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 200 [MHz]
DDR @ 600 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 512 MiB
Map: Code: 0x1feef000:0x1ff9f514
BSS: 0x1ffef8a0
Stack: 0x1f9eeef8
Heap: 0x1f9ef000:0x1feef000
NAND: (ID 0xf12c) 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Shutting down unused interfaces:
SDIO
AUDIO
TDM
Modules/Interfaces Detected:
RGMII0 Phy
RGMII1 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Net: egiga0, egiga1 [PRIME]
Power On!
FDT loaded successfully
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading /uImage-recovery
** Unable to read "/uImage-recovery" from usb 0:1 **
reading /initrd-recovery.gz
** Unable to read "/initrd-recovery.gz" from usb 0:1 **
NAND read: device 0 offset 0xd4000, size 0x6000
24576 bytes read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
And her is when i interrupt.
Terminal ready
BootROM 1.08
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.4 (COM-PHY-V20)
Update PEX Device ID 0x6710
High speed PHY - Ended Successfully
0001
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run without PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:56:14) Marvell version: v2011.12 2014_T2.0p1
06/23/2015 ReadyNAS-104 V2.0
Board: DB-88F6710-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 200 [MHz]
DDR @ 600 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 512 MiB
Map: Code: 0x1feef000:0x1ff9f514
BSS: 0x1ffef8a0
Stack: 0x1f9eeef8
Heap: 0x1f9ef000:0x1feef000
NAND: (ID 0xf12c) 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Shutting down unused interfaces:
SDIO
AUDIO
TDM
Modules/Interfaces Detected:
RGMII0 Phy
RGMII1 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Net: egiga0, egiga1 [PRIME]
Power On!
FDT loaded successfully
Hit any key to stop autoboot: 0
Marvell>> <INTERRUPT>
Marvell>> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial'
Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
Marvell>> setenv load_uinitrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd'
Marvell>> setenv usb_boot 'mw 0x800000 0 1; run load_uimage; if run load_uinitrd; then bootm 0x800000 0x2100000; else bootm 0x800000; fi'
Marvell>> setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot'
Marvell>> setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset'
Marvell>> printenv
AC_Power_fail_detect=open
CASset=min
HW_version=MVT
MALLOC_len=5
Manufacturer=NETGEAR
Product=ReadyNAS 104
SKUNum=RN104
SerialNum=3EPE51EM006E2
Startup=Normal
UUID=8ad06a7e-97fc-11e4-9cf7-e8fcafe534ca
Version=V1.0
autoload=no
bootargs=console=ttyS0,115200
bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=usb start; run usb_bootcmd; usb stop; reset
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_ubi=ubi part ubifs; ubifsmount rootfs; ubifsload 0x2000000 kernel; ubifsload 0x3000000 initrd.gz; bootm 0x2000000 0x3000000 0x1000000
bootdelay=0
cacheShare=no
console=console=ttyS0,115200
disL2Cache=yes
disaMvPnp=no
eeeEnable=no
enaAutoRecovery=yes
enaClockGating=yes
enaExtDisk=no
enaFPU=no
enaMonExt=no
enaWrAllo=no
envver=3
eth1addr=E8:FC:AF:E5:34:CB
eth1mtu=1500
ethact=egiga1
ethaddr=E8:FC:AF:E5:34:CA
ethmtu=1500
ethprime=egiga1
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-370-db.dtb
image_name=uImage
initrd_name=uInitrd
load_addr=0x02000000
load_uimage=ext2load usb 0:1 0x800000 /boot/uImage
load_uinitrd=ext2load usb 0:1 0x2100000 /boot/uInitrd
loadaddr=0x02000000
mtdids=nand0=armada-nand
mtdparts=mtdparts=armada-nand:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs)
mvNetConfig=mv_net_config=1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500
mv_pon_addr=00:50:43:00:00:02
nandEcc=1bit
netbsd_en=no
netretry=no
pcieTune=no
pexMode=rc
pxe_files_load=:default.arm-armada370-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
rcvrip=169.254.100.100
sata_delay_reset=0
sata_dma_mode=yes
setL2CacheWT=no
standalone=fsload $load_addr $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm $load_addr;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usb1Mode=host
usb2Mode=device
usbActive=0
usb_boot=mw 0x800000 0 1; run load_uimage; if run load_uinitrd; then bootm 0x800000 0x2100000; else bootm 0x800000; fi
usb_bootcmd=run usb_set_bootargs; run usb_boot
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
Environment size: 2607/131068 bytes
Marvell>> boot
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
** File not found /boot/uImage
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
9488618 bytes read
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
resetting ...
BootROM 1.08
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.4 (COM-PHY-V20)
Update PEX Device ID 0x6710
High speed PHY - Ended Successfully
0000
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run without PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:56:14) Marvell version: v2011.12 2014_T2.0p1
06/23/2015 ReadyNAS-104 V2.0
Board: DB-88F6710-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 200 [MHz]
DDR @ 600 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 512 MiB
Map: Code: 0x1feef000:0x1ff9f514
BSS: 0x1ffef8a0
Stack: 0x1f9eeef8
Heap: 0x1f9ef000:0x1feef000
NAND: (ID 0xf12c) 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Shutting down unused interfaces:
SDIO
AUDIO
TDM
Modules/Interfaces Detected:
RGMII0 Phy
RGMII1 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Net: egiga0, egiga1 [PRIME]
Power On!
FDT loaded successfully
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading /uImage-recovery
** Unable to read "/uImage-recovery" from usb 0:1 **
reading /initrd-recovery.gz
** Unable to read "/initrd-recovery.gz" from usb 0:1 **
NAND read: device 0 offset 0xd4000, size 0x6000
24576 bytes read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Marvell>>
Yes then you have it. And here come the other read out.
free -h
total used free shared buff/cache available
Mem: 3.8Gi 1.1Gi 1.1Gi 242Mi 1.6Gi 2.1Gi
Swap: 3.9Gi 0B 3.9Gi
Next one.
mount sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,relatime) proc on /proc type proc (rw,nosuid,nodev,noexec,relatime) udev on /dev type devtmpfs (rw,nosuid,relatime,size=1972148k,nr_inodes=184650,mode=755) devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000) tmpfs on /run type tmpfs (rw,nosuid,noexec,relatime,size=397584k,mode=755) /dev/sda6 on / type ext4 (rw,relatime,errors=remount-ro) securityfs on /sys/kernel/security type securityfs (rw,nosuid,nodev,noexec,relatime) tmpfs on /dev/shm type tmpfs (rw,nosuid,nodev) tmpfs on /run/lock type tmpfs (rw,nosuid,nodev,noexec,relatime,size=5120k) tmpfs on /sys/fs/cgroup type tmpfs (ro,nosuid,nodev,noexec,mode=755) cgroup2 on /sys/fs/cgroup/unified type cgroup2 (rw,nosuid,nodev,noexec,relatime,nsdelegate) cgroup on /sys/fs/cgroup/systemd type cgroup (rw,nosuid,nodev,noexec,relatime,xattr,name=systemd) pstore on /sys/fs/pstore type pstore (rw,nosuid,nodev,noexec,relatime) bpf on /sys/fs/bpf type bpf (rw,nosuid,nodev,noexec,relatime,mode=700) cgroup on /sys/fs/cgroup/perf_event type cgroup (rw,nosuid,nodev,noexec,relatime,perf_event) cgroup on /sys/fs/cgroup/cpuset type cgroup (rw,nosuid,nodev,noexec,relatime,cpuset) cgroup on /sys/fs/cgroup/cpu,cpuacct type cgroup (rw,nosuid,nodev,noexec,relatime,cpu,cpuacct) cgroup on /sys/fs/cgroup/devices type cgroup (rw,nosuid,nodev,noexec,relatime,devices) cgroup on /sys/fs/cgroup/net_cls,net_prio type cgroup (rw,nosuid,nodev,noexec,relatime,net_cls,net_prio) cgroup on /sys/fs/cgroup/rdma type cgroup (rw,nosuid,nodev,noexec,relatime,rdma) cgroup on /sys/fs/cgroup/memory type cgroup (rw,nosuid,nodev,noexec,relatime,memory) cgroup on /sys/fs/cgroup/freezer type cgroup (rw,nosuid,nodev,noexec,relatime,freezer) cgroup on /sys/fs/cgroup/pids type cgroup (rw,nosuid,nodev,noexec,relatime,pids) cgroup on /sys/fs/cgroup/blkio type cgroup (rw,nosuid,nodev,noexec,relatime,blkio) systemd-1 on /proc/sys/fs/binfmt_misc type autofs (rw,relatime,fd=25,pgrp=1,timeout=0,minproto=5,maxproto=5,direct,pipe_ino=10962) debugfs on /sys/kernel/debug type debugfs (rw,relatime) hugetlbfs on /dev/hugepages type hugetlbfs (rw,relatime,pagesize=2M) mqueue on /dev/mqueue type mqueue (rw,relatime) fusectl on /sys/fs/fuse/connections type fusectl (rw,relatime) tmpfs on /run/user/0 type tmpfs (rw,nosuid,nodev,relatime,size=397580k,mode=700) gvfsd-fuse on /run/user/0/gvfs type fuse.gvfsd-fuse (rw,nosuid,nodev,relatime,user_id=0,group_id=0) /dev/sda1 on /media/root/6979e70a-644f-45b0-9dcb-a83bbfcc3ae6 type ext4 (rw,nosuid,nodev,relatime,uhelper=udisks2) /dev/sdb1 on /media/root/rootfs type ext3 (rw,nosuid,nodev,relatime,uhelper=udisks2)Then the last command.
ls -lart /media/sdb1/boot total 46192 drwxrwxrwx 21 root root 4096 Jan 20 2017 .. -rwxr-xr-x 1 root root 5057632 Aug 19 2019 zImage-5.2.9-mvebu-tld-1 -rwxr-xr-x 1 root root 5057632 Aug 19 2019 zImage -rw-r--r-- 1 root root 183639 Aug 19 2019 config-5.2.9-mvebu-tld-1 -rw------- 1 root root 5057632 Aug 19 2019 vmlinuz-5.2.9-mvebu-tld-1 -rw------- 1 root root 3266081 Aug 19 2019 System.map-5.2.9-mvebu-tld-1 -rw-r--r-- 1 root root 9676808 Aug 19 2019 linux-headers-5.2.9-mvebu-tld-1_1.0_armhf.deb drwxr-xr-x 2 root root 4096 Aug 19 2019 dts -rw-r--r-- 1 root root 9488554 Aug 26 2019 initrd.img-5.2.9-mvebu-tld-1 -rw-r--r-- 1 root root 9488618 Aug 26 2019 uInitrd drwxr-xr-x 3 root root 4096 Sep 5 2019 .
Yes then i have done it with pri partition and now the last time with ext partition and all look the same.
Thanks again.
Best regards.
AkkJaa...
|
Re: RN10400 January 31, 2021 09:59AM |
Registered: 3 years ago Posts: 116 |
Bodhi,
Can there be some virus on the motherboard on the chip on it or something. i don't know. do you see something wrong with the read out from the motherboard.
I remember for some years ago someone talk about crypto virus or something who can atack Nas system they talk about. But eny way when we change all on the motherboard all the virus also will be gone. Yes so.
Well i don't know.
Many Thanks again.
AkkJaa..
By the way the connect on the serial header is J14 on the RN10400 or RN104 but was differnt from RN102. because RX was TX and TX was RX from the RN102 to the RN104. but that have nothing to say now because it read out good now.
Can there be some virus on the motherboard on the chip on it or something. i don't know. do you see something wrong with the read out from the motherboard.
I remember for some years ago someone talk about crypto virus or something who can atack Nas system they talk about. But eny way when we change all on the motherboard all the virus also will be gone. Yes so.
Well i don't know.
Many Thanks again.
AkkJaa..
By the way the connect on the serial header is J14 on the RN10400 or RN104 but was differnt from RN102. because RX was TX and TX was RX from the RN102 to the RN104. but that have nothing to say now because it read out good now.
|
Re: RN10400 January 31, 2021 03:54PM |
Admin Registered: 13 years ago Posts: 18,548 |
AkkJaa,
> Can there be some virus on the motherboard on the
> chip on it or something. i don't know. do you see
> something wrong with the read out from the
> motherboard.
No. Let me revise the instruction corresponding to your Linux host's behavior (below after the break).
> By the way the connect on the serial header is J14
> on the RN10400 or RN104 but was differnt from
> RN102. because RX was TX and TX was RX from the
> RN102 to the RN104. but that have nothing to say
> now because it read out good now.
Sometime in the future, you want to post the serial pinouts here (in ASCII text, or picture) so it can be benefited by newcomers.
======
Here is what you did wrong.
On your Linux host the mounting was done autotmatically, and it assigned the mount point using partition label (instead of sdb1)
So you want to cd to that directory and then untar the rootfs tarball. Remeber to sync a dew times (same as Windows Safely Remove)
And then
To see the typical behavor of a Linux system. Now remove the USB rootfs. Check the mountpoints. It is gone.
And then plug it in again so this Linux host can automount the drive. Check the mount ponts
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> Can there be some virus on the motherboard on the
> chip on it or something. i don't know. do you see
> something wrong with the read out from the
> motherboard.
No. Let me revise the instruction corresponding to your Linux host's behavior (below after the break).
> By the way the connect on the serial header is J14
> on the RN10400 or RN104 but was differnt from
> RN102. because RX was TX and TX was RX from the
> RN102 to the RN104. but that have nothing to say
> now because it read out good now.
Sometime in the future, you want to post the serial pinouts here (in ASCII text, or picture) so it can be benefited by newcomers.
======
Here is what you did wrong.
On your Linux host the mounting was done autotmatically, and it assigned the mount point using partition label (instead of sdb1)
mount ... /dev/sdb1 on /media/root/rootfs type ext3 (rw,nosuid,nodev,relatime,uhelper=udisks2)
So you want to cd to that directory and then untar the rootfs tarball. Remeber to sync a dew times (same as Windows Safely Remove)
cd /media/root/rootfs tar -xjf Debian-5.2.9-mvebu-tld-1-rootfs-bodhi.tar.bz2 sync sync
And then
umount /media/root/rootfsNow you have the rootfs in the USB.
To see the typical behavor of a Linux system. Now remove the USB rootfs. Check the mountpoints. It is gone.
mount
And then plug it in again so this Linux host can automount the drive. Check the mount ponts
mountNow you will see it is mounted at /media/root/rootfs again.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: RN10400 February 01, 2021 01:31AM |
Registered: 3 years ago Posts: 116 |
Bodhi,
> By the way the connect on the serial header is J14
> on the RN10400 or RN104 but was differnt from
> RN102. because RX was TX and TX was RX from the
> RN102 to the RN104. but that have nothing to say
> now because it read out good now.
>Sometime in the future, you want to post the serial pinouts here (in ASCII text, or picture) so it can be benefited by >newcomers.
Yes you are right, i will take a picture of the RN104 motherboard from behind and and mark what is the right connecting on the serial header J14 on the motherboard RN104. model name RN10400.
Ok, i understand what i did wrong now so i will try again and post it out here.
Well, many thanks again.
AkkJaa...
> By the way the connect on the serial header is J14
> on the RN10400 or RN104 but was differnt from
> RN102. because RX was TX and TX was RX from the
> RN102 to the RN104. but that have nothing to say
> now because it read out good now.
>Sometime in the future, you want to post the serial pinouts here (in ASCII text, or picture) so it can be benefited by >newcomers.
Yes you are right, i will take a picture of the RN104 motherboard from behind and and mark what is the right connecting on the serial header J14 on the motherboard RN104. model name RN10400.
Ok, i understand what i did wrong now so i will try again and post it out here.
Well, many thanks again.
AkkJaa...
|
Re: RN10400 February 05, 2021 07:15AM |
Registered: 3 years ago Posts: 116 |
Hi Bodhi,
Now i have try the last one, here is the read out.-
I forget to interrupt this so i try again here.
Yes then here come the rest.
Thanks again.
AkkJaa...
Now i have try the last one, here is the read out.-
Terminal ready
BootROM 1.08
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.4 (COM-PHY-V20)
Update PEX Device ID 0x6710
High speed PHY - Ended Successfully
0001
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run without PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:56:14) Marvell version: v2011.12 2014_T2.0p1
06/23/2015 ReadyNAS-104 V2.0
Board: DB-88F6710-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 200 [MHz]
DDR @ 600 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 512 MiB
Map: Code: 0x1feef000:0x1ff9f514
BSS: 0x1ffef8a0
Stack: 0x1f9eeef8
Heap: 0x1f9ef000:0x1feef000
NAND: (ID 0xf12c) 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Shutting down unused interfaces:
SDIO
AUDIO
TDM
Modules/Interfaces Detected:
RGMII0 Phy
RGMII1 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Net: egiga0, egiga1 [PRIME]
Power On!
FDT loaded successfully
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading /uImage-recovery
** Unable to read "/uImage-recovery" from usb 0:1 **
reading /initrd-recovery.gz
** Unable to read "/initrd-recovery.gz" from usb 0:1 **
NAND read: device 0 offset 0xd4000, size 0x6000
24576 bytes read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Marvell>> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial'
Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
Marvell>> setenv load_uinitrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd'
Marvell>> setenv usb_boot 'mw 0x800000 0 1; run load_uimage; if run load_uinitrd; then bootm 0x800000 0x2100000; else bootm 0x800000; fi'
Marvell>> setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot'
Marvell>> setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset'
Marvell>> printenv
AC_Power_fail_detect=open
CASset=min
HW_version=MVT
MALLOC_len=5
Manufacturer=NETGEAR
Product=ReadyNAS 104
SKUNum=RN104
SerialNum=3EPE51EM006E2
Startup=Normal
UUID=8ad06a7e-97fc-11e4-9cf7-e8fcafe534ca
Version=V1.0
autoload=no
bootargs=console=ttyS0,115200
bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=usb start; run usb_bootcmd; usb stop; reset
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_ubi=ubi part ubifs; ubifsmount rootfs; ubifsload 0x2000000 kernel; ubifsload 0x3000000 initrd.gz; bootm 0x2000000 0x3000000 0x1000000
bootdelay=0
cacheShare=no
console=console=ttyS0,115200
disL2Cache=yes
disaMvPnp=no
eeeEnable=no
enaAutoRecovery=yes
enaClockGating=yes
enaExtDisk=no
enaFPU=no
enaMonExt=no
enaWrAllo=no
envver=3
eth1addr=E8:FC:AF:E5:34:CB
eth1mtu=1500
ethact=egiga1
ethaddr=E8:FC:AF:E5:34:CA
ethmtu=1500
ethprime=egiga1
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-370-db.dtb
image_name=uImage
initrd_name=uInitrd
load_addr=0x02000000
load_uimage=ext2load usb 0:1 0x800000 /boot/uImage
load_uinitrd=ext2load usb 0:1 0x2100000 /boot/uInitrd
loadaddr=0x02000000
mtdids=nand0=armada-nand
mtdparts=mtdparts=armada-nand:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs)
mvNetConfig=mv_net_config=1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500
mv_pon_addr=00:50:43:00:00:02
nandEcc=1bit
netbsd_en=no
netretry=no
pcieTune=no
pexMode=rc
pxe_files_load=:default.arm-armada370-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
rcvrip=169.254.100.100
sata_delay_reset=0
sata_dma_mode=yes
setL2CacheWT=no
standalone=fsload $load_addr $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm $load_addr;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usb1Mode=host
usb2Mode=device
usbActive=0
usb_boot=mw 0x800000 0 1; run load_uimage; if run load_uinitrd; then bootm 0x800000 0x2100000; else bootm 0x800000; fi
usb_bootcmd=run usb_set_bootargs; run usb_boot
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
Environment size: 2607/131068 bytes
Marvell>> boot
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
** File not found /boot/uImage
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
9488618 bytes read
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
resetting ...
BootROM 1.08
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.4 (COM-PHY-V20)
Update PEX Device ID 0x6710
High speed PHY - Ended Successfully
0000
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run without PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:56:14) Marvell version: v2011.12 2014_T2.0p1
06/23/2015 ReadyNAS-104 V2.0
Board: DB-88F6710-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 200 [MHz]
DDR @ 600 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 512 MiB
Map: Code: 0x1feef000:0x1ff9f514
BSS: 0x1ffef8a0
Stack: 0x1f9eeef8
Heap: 0x1f9ef000:0x1feef000
NAND: (ID 0xf12c) 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Shutting down unused interfaces:
SDIO
AUDIO
TDM
Modules/Interfaces Detected:
RGMII0 Phy
RGMII1 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Net: egiga0, egiga1 [PRIME]
Power On!
FDT loaded successfully
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading /uImage-recovery
** Unable to read "/uImage-recovery" from usb 0:1 **
reading /initrd-recovery.gz
** Unable to read "/initrd-recovery.gz" from usb 0:1 **
NAND read: device 0 offset 0xd4000, size 0x6000
24576 bytes read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Marvell>>
FATAL: read zero bytes from port
term_exitfunc: reset failed for dev UNKNOWN: Input/output error
I forget to interrupt this so i try again here.
Terminal ready
BootROM 1.08
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.4 (COM-PHY-V20)
Update PEX Device ID 0x6710
High speed PHY - Ended Successfully
0001
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run without PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:56:14) Marvell version: v2011.12 2014_T2.0p1
06/23/2015 ReadyNAS-104 V2.0
Board: DB-88F6710-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 200 [MHz]
DDR @ 600 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 512 MiB
Port0: phyAddr=0x0, Not Marvell PHY id1 ffff id2 ffff
PHY error - shutdown port0
Map: Code: 0x1feef000:0x1ff9f514
BSS: 0x1ffef8a0
Stack: 0x1f9eeef8
Heap: 0x1f9ef000:0x1feef000
NAND: (ID 0xf12c) 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Shutting down unused interfaces:
SDIO
AUDIO
TDM
Modules/Interfaces Detected:
RGMII0 Phy
RGMII1 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Net: egiga1 [PRIME]
Warning: egiga1 MAC addresses don't match:
Address in SROM is e8:fc:af:e5:34:cb
Address in environment is e8:fc:af:e5:34:ca
Power On!
FDT loaded successfully
Hit any key to stop autoboot: 0
Marvell>> <INTERRUPT>
Marvell>> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial'
Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
Marvell>> setenv load_uinitrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd'
Marvell>> setenv usb_boot 'mw 0x800000 0 1; run load_uimage; if run load_uinitrd; then bootm 0x800000 0x2100000; else bootm 0x800000; fi'
Marvell>> setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot'
Marvell>> setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset'
Marvell>> printenv
AC_Power_fail_detect=open
CASset=min
HW_version=MVT
MALLOC_len=5
Manufacturer=NETGEAR
Product=ReadyNAS 104
SKUNum=RN104
SerialNum=3EPE51EM006E2
Startup=Normal
UUID=8ad06a7e-97fc-11e4-9cf7-e8fcafe534ca
Version=V1.0
autoload=no
bootargs=console=ttyS0,115200
bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=usb start; run usb_bootcmd; usb stop; reset
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_ubi=ubi part ubifs; ubifsmount rootfs; ubifsload 0x2000000 kernel; ubifsload 0x3000000 initrd.gz; bootm 0x2000000 0x3000000 0x1000000
bootdelay=0
cacheShare=no
console=console=ttyS0,115200
disL2Cache=yes
disaMvPnp=no
eeeEnable=no
enaAutoRecovery=yes
enaClockGating=yes
enaExtDisk=no
enaFPU=no
enaMonExt=no
enaWrAllo=no
envver=3
eth1addr=E8:FC:AF:E5:34:CB
eth1mtu=1500
ethact=egiga1
ethaddr=E8:FC:AF:E5:34:CA
ethmtu=1500
ethprime=egiga1
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-370-db.dtb
image_name=uImage
initrd_name=uInitrd
load_addr=0x02000000
load_uimage=ext2load usb 0:1 0x800000 /boot/uImage
load_uinitrd=ext2load usb 0:1 0x2100000 /boot/uInitrd
loadaddr=0x02000000
mtdids=nand0=armada-nand
mtdparts=mtdparts=armada-nand:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs)
mvNetConfig=mv_net_config=1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500
mv_pon_addr=00:50:43:00:00:02
nandEcc=1bit
netbsd_en=no
netretry=no
pcieTune=no
pexMode=rc
pxe_files_load=:default.arm-armada370-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
rcvrip=169.254.100.100
sata_delay_reset=0
sata_dma_mode=yes
setL2CacheWT=no
standalone=fsload $load_addr $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm $load_addr;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usb1Mode=host
usb2Mode=device
usbActive=0
usb_boot=mw 0x800000 0 1; run load_uimage; if run load_uinitrd; then bootm 0x800000 0x2100000; else bootm 0x800000; fi
usb_bootcmd=run usb_set_bootargs; run usb_boot
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
Environment size: 2607/131068 bytes
Marvell>> boot
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
** File not found /boot/uImage
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
9488618 bytes read
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
resetting ...
BootROM 1.08
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.4 (COM-PHY-V20)
Update PEX Device ID 0x6710
High speed PHY - Ended Successfully
0000
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run without PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:56:14) Marvell version: v2011.12 2014_T2.0p1
06/23/2015 ReadyNAS-104 V2.0
Board: DB-88F6710-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 200 [MHz]
DDR @ 600 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 512 MiB
Port0: phyAddr=0x0, Not Marvell PHY id1 ffff id2 ffff
PHY error - shutdown port0
Map: Code: 0x1feef000:0x1ff9f514
BSS: 0x1ffef8a0
Stack: 0x1f9eeef8
Heap: 0x1f9ef000:0x1feef000
NAND: (ID 0xf12c) 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Shutting down unused interfaces:
SDIO
AUDIO
TDM
Modules/Interfaces Detected:
RGMII0 Phy
RGMII1 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Net: egiga1 [PRIME]
Warning: egiga1 MAC addresses don't match:
Address in SROM is e8:fc:af:e5:34:cb
Address in environment is e8:fc:af:e5:34:ca
Power On!
FDT loaded successfully
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading /uImage-recovery
** Unable to read "/uImage-recovery" from usb 0:1 **
reading /initrd-recovery.gz
** Unable to read "/initrd-recovery.gz" from usb 0:1 **
NAND read: device 0 offset 0xd4000, size 0x6000
24576 bytes read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Marvell>>
Yes then here come the rest.
free -h
total used free shared buff/cache available
Mem: 3.8Gi 1.1Gi 1.1Gi 240Mi 1.7Gi 2.2Gi
Swap: 3.9Gi 0B 3.9Gi
Then next one.
mount sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,relatime) proc on /proc type proc (rw,nosuid,nodev,noexec,relatime) udev on /dev type devtmpfs (rw,nosuid,relatime,size=1972544k,nr_inodes=184848,mode=755) devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000) tmpfs on /run type tmpfs (rw,nosuid,noexec,relatime,size=397664k,mode=755) /dev/sda6 on / type ext4 (rw,relatime,errors=remount-ro) securityfs on /sys/kernel/security type securityfs (rw,nosuid,nodev,noexec,relatime) tmpfs on /dev/shm type tmpfs (rw,nosuid,nodev) tmpfs on /run/lock type tmpfs (rw,nosuid,nodev,noexec,relatime,size=5120k) tmpfs on /sys/fs/cgroup type tmpfs (ro,nosuid,nodev,noexec,mode=755) cgroup2 on /sys/fs/cgroup/unified type cgroup2 (rw,nosuid,nodev,noexec,relatime,nsdelegate) cgroup on /sys/fs/cgroup/systemd type cgroup (rw,nosuid,nodev,noexec,relatime,xattr,name=systemd) pstore on /sys/fs/pstore type pstore (rw,nosuid,nodev,noexec,relatime) bpf on /sys/fs/bpf type bpf (rw,nosuid,nodev,noexec,relatime,mode=700) cgroup on /sys/fs/cgroup/cpu,cpuacct type cgroup (rw,nosuid,nodev,noexec,relatime,cpu,cpuacct) cgroup on /sys/fs/cgroup/freezer type cgroup (rw,nosuid,nodev,noexec,relatime,freezer) cgroup on /sys/fs/cgroup/memory type cgroup (rw,nosuid,nodev,noexec,relatime,memory) cgroup on /sys/fs/cgroup/rdma type cgroup (rw,nosuid,nodev,noexec,relatime,rdma) cgroup on /sys/fs/cgroup/net_cls,net_prio type cgroup (rw,nosuid,nodev,noexec,relatime,net_cls,net_prio) cgroup on /sys/fs/cgroup/devices type cgroup (rw,nosuid,nodev,noexec,relatime,devices) cgroup on /sys/fs/cgroup/cpuset type cgroup (rw,nosuid,nodev,noexec,relatime,cpuset) cgroup on /sys/fs/cgroup/perf_event type cgroup (rw,nosuid,nodev,noexec,relatime,perf_event) cgroup on /sys/fs/cgroup/pids type cgroup (rw,nosuid,nodev,noexec,relatime,pids) cgroup on /sys/fs/cgroup/blkio type cgroup (rw,nosuid,nodev,noexec,relatime,blkio) systemd-1 on /proc/sys/fs/binfmt_misc type autofs (rw,relatime,fd=33,pgrp=1,timeout=0,minproto=5,maxproto=5,direct,pipe_ino=13323) hugetlbfs on /dev/hugepages type hugetlbfs (rw,relatime,pagesize=2M) debugfs on /sys/kernel/debug type debugfs (rw,relatime) mqueue on /dev/mqueue type mqueue (rw,relatime) fusectl on /sys/fs/fuse/connections type fusectl (rw,relatime) tmpfs on /run/user/0 type tmpfs (rw,nosuid,nodev,relatime,size=397660k,mode=700) gvfsd-fuse on /run/user/0/gvfs type fuse.gvfsd-fuse (rw,nosuid,nodev,relatime,user_id=0,group_id=0) /dev/sda1 on /media/root/6979e70a-644f-45b0-9dcb-a83bbfcc3ae6 type ext4 (rw,nosuid,nodev,relatime,uhelper=udisks2) /dev/sdb1 on /media/root/rootfs type ext3 (rw,nosuid,nodev,relatime,uhelper=udisks2)And last one.
ls -lart /media/sdb1/boot total 46192 drwxrwxrwx 21 root root 4096 Jan 20 2017 .. -rwxr-xr-x 1 root root 5057632 Aug 19 2019 zImage-5.2.9-mvebu-tld-1 -rwxr-xr-x 1 root root 5057632 Aug 19 2019 zImage -rw-r--r-- 1 root root 183639 Aug 19 2019 config-5.2.9-mvebu-tld-1 -rw------- 1 root root 5057632 Aug 19 2019 vmlinuz-5.2.9-mvebu-tld-1 -rw------- 1 root root 3266081 Aug 19 2019 System.map-5.2.9-mvebu-tld-1 -rw-r--r-- 1 root root 9676808 Aug 19 2019 linux-headers-5.2.9-mvebu-tld-1_1.0_armhf.deb drwxr-xr-x 2 root root 4096 Aug 19 2019 dts -rw-r--r-- 1 root root 9488554 Aug 26 2019 initrd.img-5.2.9-mvebu-tld-1 -rw-r--r-- 1 root root 9488618 Aug 26 2019 uInitrd drwxr-xr-x 3 root root 4096 Sep 5 2019 .Yes and now i use this.:-
cd /media/root/rootfs tar -xjf Debian-5.2.9-mvebu-tld-1-rootfs-bodhi.tar.bz2 sync syncBut it look like the same or what do you think.
Thanks again.
AkkJaa...
|
Re: RN10400 February 05, 2021 09:16AM |
Registered: 3 years ago Posts: 116 |
Hi Bodhi,
Here i have take some photos of the RN104 motherboard and i have mark on each picture what is the right connection for the serial header J14 on the RN104 motherboard. model name RN10400.
Yes now i will try one more time what you have say.
Many thanks again.
Best Regards.
AkkJaa...
Here i have take some photos of the RN104 motherboard and i have mark on each picture what is the right connection for the serial header J14 on the RN104 motherboard. model name RN10400.
Yes now i will try one more time what you have say.
Many thanks again.
Best Regards.
AkkJaa...
|
Re: RN10400 February 05, 2021 04:59PM |
Admin Registered: 13 years ago Posts: 18,548 |
AkkJaa,
There should be no files in /media/sdb1. To avoid confusing the issue, before plugging in the USB drive to format it, delele this folder and everything underneath:
(be extra careful when you do this, rm-rf at the wrong place would wipe out your Linux host file system)
Plug in the USB drive. In your Linux host the USB drive is mounted at
/media/root/rootfs
So it was correct to untar the rootfs to it:
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
Quote
ls -lart /media/sdb1/boot
There should be no files in /media/sdb1. To avoid confusing the issue, before plugging in the USB drive to format it, delele this folder and everything underneath:
(be extra careful when you do this, rm-rf at the wrong place would wipe out your Linux host file system)
rm /media/sdb1 -rfNow you have no /media/sdb1 folder.
Plug in the USB drive. In your Linux host the USB drive is mounted at
/media/root/rootfs
So it was correct to untar the rootfs to it:
cd /media/root/rootfs tar -xjf Debian-5.2.9-mvebu-tld-1-rootfs-bodhi.tar.bz2 sync sync
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: RN10400 February 05, 2021 04:59PM |
Admin Registered: 13 years ago Posts: 18,548 |
> Here i have take some photos of the RN104
> motherboard and i have mark on each picture what
> is the right connection for the serial header J14
> on the RN104 motherboard. model name RN10400.
Thanks!
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> motherboard and i have mark on each picture what
> is the right connection for the serial header J14
> on the RN104 motherboard. model name RN10400.
Thanks!
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: RN10400 February 06, 2021 01:37AM |
Registered: 3 years ago Posts: 116 |
Bodhi,
Here i have try one more time and here is the read out.-
i think it is the same. but longer time to boot up.
Then here come this command.
Thanks again.
AkkJaa...
Here i have try one more time and here is the read out.-
Terminal ready
BootROM 1.08
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.4 (COM-PHY-V20)
Update PEX Device ID 0x6710
High speed PHY - Ended Successfully
0001
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run without PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:56:14) Marvell version: v2011.12 2014_T2.0p1
06/23/2015 ReadyNAS-104 V2.0
Board: DB-88F6710-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 200 [MHz]
DDR @ 600 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 512 MiB
Map: Code: 0x1feef000:0x1ff9f514
BSS: 0x1ffef8a0
Stack: 0x1f9eeef8
Heap: 0x1f9ef000:0x1feef000
NAND: (ID 0xf12c) 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Shutting down unused interfaces:
SDIO
AUDIO
TDM
Modules/Interfaces Detected:
RGMII0 Phy
RGMII1 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Net: egiga0, egiga1 [PRIME]
Power On!
FDT loaded successfully
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading /uImage-recovery
** Unable to read "/uImage-recovery" from usb 0:1 **
reading /initrd-recovery.gz
** Unable to read "/initrd-recovery.gz" from usb 0:1 **
NAND read: device 0 offset 0xd4000, size 0x6000
24576 bytes read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Marvell>>
Marvell>> printenv
AC_Power_fail_detect=open
CASset=min
HW_version=MVT
MALLOC_len=5
Manufacturer=NETGEAR
Product=ReadyNAS 104
SKUNum=RN104
SerialNum=3EPE51EM006E2
Startup=Normal
UUID=8ad06a7e-97fc-11e4-9cf7-e8fcafe534ca
Version=V1.0
autoload=no
bootargs=console=ttyS0,115200
bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=usb start;fatload usb 0:1 0x2000000 /uImage-recovery;fatload usb 0:1 0x3000000 /initrd-recovery.gz;nand read 0x1000000 0xD4000 0x6000; bootm 0x2000000 0x3000000 0x1000000
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_ubi=ubi part ubifs; ubifsmount rootfs; ubifsload 0x2000000 kernel; ubifsload 0x3000000 initrd.gz; bootm 0x2000000 0x3000000 0x1000000
bootdelay=0
cacheShare=no
console=console=ttyS0,115200
disL2Cache=yes
disaMvPnp=no
eeeEnable=no
enaAutoRecovery=yes
enaClockGating=yes
enaExtDisk=no
enaFPU=no
enaMonExt=no
enaWrAllo=no
envver=3
eth1addr=E8:FC:AF:E5:34:CB
eth1mtu=1500
ethact=egiga1
ethaddr=E8:FC:AF:E5:34:CA
ethmtu=1500
ethprime=egiga1
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-370-db.dtb
image_name=uImage
initrd_name=uInitrd
load_addr=0x02000000
loadaddr=0x02000000
mtdids=nand0=armada-nand
mtdparts=mtdparts=armada-nand:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs)
mvNetConfig=mv_net_config=1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500
mv_pon_addr=00:50:43:00:00:02
nandEcc=1bit
netbsd_en=no
netretry=no
pcieTune=no
pexMode=rc
pxe_files_load=:default.arm-armada370-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
rcvrip=169.254.100.100
sata_delay_reset=0
sata_dma_mode=yes
setL2CacheWT=no
standalone=fsload $load_addr $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm $load_addr;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usb1Mode=host
usb2Mode=device
usbActive=0
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
Environment size: 2349/131068 bytes
Marvell>>
Yes that was the first and here come the readout after i put in the setenv send me.
FDT loaded successfully
Hit any key to stop autoboot: 0
Marvell>> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial'
Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
Marvell>> setenv load_uinitrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd'
Marvell>> setenv usb_boot 'mw 0x800000 0 1; run load_uimage; if run load_uinitrd; then bootm 0x800000 0x2100000; else bootm 0x800000; fi'
Marvell>> setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot'
Marvell>> setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset'
Marvell>> printenv
AC_Power_fail_detect=open
CASset=min
HW_version=MVT
MALLOC_len=5
Manufacturer=NETGEAR
Product=ReadyNAS 104
SKUNum=RN104
SerialNum=3EPE51EM006E2
Startup=Normal
UUID=8ad06a7e-97fc-11e4-9cf7-e8fcafe534ca
Version=V1.0
autoload=no
bootargs=console=ttyS0,115200
bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=usb start; run usb_bootcmd; usb stop; reset
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_ubi=ubi part ubifs; ubifsmount rootfs; ubifsload 0x2000000 kernel; ubifsload 0x3000000 initrd.gz; bootm 0x2000000 0x3000000 0x1000000
bootdelay=0
cacheShare=no
console=console=ttyS0,115200
disL2Cache=yes
disaMvPnp=no
eeeEnable=no
enaAutoRecovery=yes
enaClockGating=yes
enaExtDisk=no
enaFPU=no
enaMonExt=no
enaWrAllo=no
envver=3
eth1addr=E8:FC:AF:E5:34:CB
eth1mtu=1500
ethact=egiga1
ethaddr=E8:FC:AF:E5:34:CA
ethmtu=1500
ethprime=egiga1
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-370-db.dtb
image_name=uImage
initrd_name=uInitrd
load_addr=0x02000000
load_uimage=ext2load usb 0:1 0x800000 /boot/uImage
load_uinitrd=ext2load usb 0:1 0x2100000 /boot/uInitrd
loadaddr=0x02000000
mtdids=nand0=armada-nand
mtdparts=mtdparts=armada-nand:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs)
mvNetConfig=mv_net_config=1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500
mv_pon_addr=00:50:43:00:00:02
nandEcc=1bit
netbsd_en=no
netretry=no
pcieTune=no
pexMode=rc
pxe_files_load=:default.arm-armada370-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
rcvrip=169.254.100.100
sata_delay_reset=0
sata_dma_mode=yes
setL2CacheWT=no
standalone=fsload $load_addr $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm $load_addr;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usb1Mode=host
usb2Mode=device
usbActive=0
usb_boot=mw 0x800000 0 1; run load_uimage; if run load_uinitrd; then bootm 0x800000 0x2100000; else bootm 0x800000; fi
usb_bootcmd=run usb_set_bootargs; run usb_boot
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
Environment size: 2607/131068 bytes
Marvell>> boot
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
** File not found /boot/uImage
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
9488618 bytes read
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
resetting ...
BootROM 1.08
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.4 (COM-PHY-V20)
Update PEX Device ID 0x6710
High speed PHY - Ended Successfully
0000
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run without PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:56:14) Marvell version: v2011.12 2014_T2.0p1
06/23/2015 ReadyNAS-104 V2.0
Board: DB-88F6710-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 200 [MHz]
DDR @ 600 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 512 MiB
Port0: phyAddr=0x0, Not Marvell PHY id1 ffff id2 ffff
PHY error - shutdown port0
Map: Code: 0x1feef000:0x1ff9f514
BSS: 0x1ffef8a0
Stack: 0x1f9eeef8
Heap: 0x1f9ef000:0x1feef000
NAND: (ID 0xf12c) 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Shutting down unused interfaces:
SDIO
AUDIO
TDM
Modules/Interfaces Detected:
RGMII0 Phy
RGMII1 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Net: egiga1 [PRIME]
Warning: egiga1 MAC addresses don't match:
Address in SROM is e8:fc:af:e5:34:cb
Address in environment is e8:fc:af:e5:34:ca
Power On!
FDT loaded successfully
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading /uImage-recovery
** Unable to read "/uImage-recovery" from usb 0:1 **
reading /initrd-recovery.gz
** Unable to read "/initrd-recovery.gz" from usb 0:1 **
NAND read: device 0 offset 0xd4000, size 0x6000
24576 bytes read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Marvell>>
i think it is the same. but longer time to boot up.
Then here come this command.
free -h
total used free shared buff/cache available
Mem: 3.8Gi 1.0Gi 1.1Gi 199Mi 1.7Gi 2.2Gi
Swap: 3.9Gi 0B 3.9Gi
And then this command.
mount sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,relatime) proc on /proc type proc (rw,nosuid,nodev,noexec,relatime) udev on /dev type devtmpfs (rw,nosuid,relatime,size=1972544k,nr_inodes=184848,mode=755) devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000) tmpfs on /run type tmpfs (rw,nosuid,noexec,relatime,size=397664k,mode=755) /dev/sda6 on / type ext4 (rw,relatime,errors=remount-ro) securityfs on /sys/kernel/security type securityfs (rw,nosuid,nodev,noexec,relatime) tmpfs on /dev/shm type tmpfs (rw,nosuid,nodev) tmpfs on /run/lock type tmpfs (rw,nosuid,nodev,noexec,relatime,size=5120k) tmpfs on /sys/fs/cgroup type tmpfs (ro,nosuid,nodev,noexec,mode=755) cgroup2 on /sys/fs/cgroup/unified type cgroup2 (rw,nosuid,nodev,noexec,relatime,nsdelegate) cgroup on /sys/fs/cgroup/systemd type cgroup (rw,nosuid,nodev,noexec,relatime,xattr,name=systemd) pstore on /sys/fs/pstore type pstore (rw,nosuid,nodev,noexec,relatime) bpf on /sys/fs/bpf type bpf (rw,nosuid,nodev,noexec,relatime,mode=700) cgroup on /sys/fs/cgroup/cpu,cpuacct type cgroup (rw,nosuid,nodev,noexec,relatime,cpu,cpuacct) cgroup on /sys/fs/cgroup/freezer type cgroup (rw,nosuid,nodev,noexec,relatime,freezer) cgroup on /sys/fs/cgroup/memory type cgroup (rw,nosuid,nodev,noexec,relatime,memory) cgroup on /sys/fs/cgroup/rdma type cgroup (rw,nosuid,nodev,noexec,relatime,rdma) cgroup on /sys/fs/cgroup/net_cls,net_prio type cgroup (rw,nosuid,nodev,noexec,relatime,net_cls,net_prio) cgroup on /sys/fs/cgroup/devices type cgroup (rw,nosuid,nodev,noexec,relatime,devices) cgroup on /sys/fs/cgroup/cpuset type cgroup (rw,nosuid,nodev,noexec,relatime,cpuset) cgroup on /sys/fs/cgroup/perf_event type cgroup (rw,nosuid,nodev,noexec,relatime,perf_event) cgroup on /sys/fs/cgroup/pids type cgroup (rw,nosuid,nodev,noexec,relatime,pids) cgroup on /sys/fs/cgroup/blkio type cgroup (rw,nosuid,nodev,noexec,relatime,blkio) systemd-1 on /proc/sys/fs/binfmt_misc type autofs (rw,relatime,fd=33,pgrp=1,timeout=0,minproto=5,maxproto=5,direct,pipe_ino=13323) hugetlbfs on /dev/hugepages type hugetlbfs (rw,relatime,pagesize=2M) debugfs on /sys/kernel/debug type debugfs (rw,relatime) mqueue on /dev/mqueue type mqueue (rw,relatime) fusectl on /sys/fs/fuse/connections type fusectl (rw,relatime) tmpfs on /run/user/0 type tmpfs (rw,nosuid,nodev,relatime,size=397660k,mode=700) gvfsd-fuse on /run/user/0/gvfs type fuse.gvfsd-fuse (rw,nosuid,nodev,relatime,user_id=0,group_id=0) /dev/sda1 on /media/root/6979e70a-644f-45b0-9dcb-a83bbfcc3ae6 type ext4 (rw,nosuid,nodev,relatime,uhelper=udisks2) /dev/sdb1 on /media/root/rootfs type ext3 (rw,nosuid,nodev,relatime,uhelper=udisks2)Then the last command.
ls -lart /media/sdb1/boot total 46192 drwxrwxrwx 21 root root 4096 Jan 20 2017 .. -rwxr-xr-x 1 root root 5057632 Aug 19 2019 zImage-5.2.9-mvebu-tld-1 -rwxr-xr-x 1 root root 5057632 Aug 19 2019 zImage -rw-r--r-- 1 root root 183639 Aug 19 2019 config-5.2.9-mvebu-tld-1 -rw------- 1 root root 5057632 Aug 19 2019 vmlinuz-5.2.9-mvebu-tld-1 -rw------- 1 root root 3266081 Aug 19 2019 System.map-5.2.9-mvebu-tld-1 -rw-r--r-- 1 root root 9676808 Aug 19 2019 linux-headers-5.2.9-mvebu-tld-1_1.0_armhf.deb drwxr-xr-x 2 root root 4096 Aug 19 2019 dts -rw-r--r-- 1 root root 9488554 Aug 26 2019 initrd.img-5.2.9-mvebu-tld-1 -rw-r--r-- 1 root root 9488618 Aug 26 2019 uInitrd drwxr-xr-x 3 root root 4096 Sep 5 2019 .Yes this was one more time i try it and what do you see here.
Thanks again.
AkkJaa...
|
Re: RN10400 February 06, 2021 01:52AM |
Registered: 3 years ago Posts: 116 |
Bodhi,
Ok i will try this now.
Thanks.
AkkJaa...
Quote
There should be no files in /media/sdb1. To avoid confusing the issue, before plugging in the USB drive to format it, delele this folder and everything underneath:
(be extra careful when you do this, rm-rf at the wrong place would wipe out your Linux host file system
Ok i will try this now.
Thanks.
AkkJaa...
|
Re: RN10400 February 06, 2021 12:17PM |
Registered: 3 years ago Posts: 116 |
Bodhi,
Here come the read out from the new USB drive i make.
Then.
And
And the last one.
Yes and when i look into the mapps / file system then the USB drive have the name
rootfs
And dir look like this.
/media/root/rootfs(/dev/sdb1)
Yes then i have it.
Thanks again.
AkkJaa...
Here come the read out from the new USB drive i make.
Terminal ready
BootROM 1.08
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.4 (COM-PHY-V20)
Update PEX Device ID 0x6710
High speed PHY - Ended Successfully
0001
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run without PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:56:14) Marvell version: v2011.12 2014_T2.0p1
06/23/2015 ReadyNAS-104 V2.0
Board: DB-88F6710-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 200 [MHz]
DDR @ 600 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 512 MiB
Port0: phyAddr=0x0, Not Marvell PHY id1 ffff id2 ffff
PHY error - shutdown port0
Map: Code: 0x1feef000:0x1ff9f514
BSS: 0x1ffef8a0
Stack: 0x1f9eeef8
Heap: 0x1f9ef000:0x1feef000
NAND: (ID 0xf12c) 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Shutting down unused interfaces:
SDIO
AUDIO
TDM
Modules/Interfaces Detected:
RGMII0 Phy
RGMII1 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Net: egiga1 [PRIME]
Warning: egiga1 MAC addresses don't match:
Address in SROM is e8:fc:af:e5:34:cb
Address in environment is e8:fc:af:e5:34:ca
Power On!
FDT loaded successfully
Hit any key to stop autoboot: 0
Marvell>> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial'
Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
Marvell>> setenv load_uinitrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd'
Marvell>> setenv usb_boot 'mw 0x800000 0 1; run load_uimage; if run load_uinitrd; then bootm 0x800000 0x2100000; else bootm 0x800000; fi'
Marvell>> setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot'
Marvell>> setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset'
Marvell>> printenv
AC_Power_fail_detect=open
CASset=min
HW_version=MVT
MALLOC_len=5
Manufacturer=NETGEAR
Product=ReadyNAS 104
SKUNum=RN104
SerialNum=3EPE51EM006E2
Startup=Normal
UUID=8ad06a7e-97fc-11e4-9cf7-e8fcafe534ca
Version=V1.0
autoload=no
bootargs=console=ttyS0,115200
bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=usb start; run usb_bootcmd; usb stop; reset
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_ubi=ubi part ubifs; ubifsmount rootfs; ubifsload 0x2000000 kernel; ubifsload 0x3000000 initrd.gz; bootm 0x2000000 0x3000000 0x1000000
bootdelay=0
cacheShare=no
console=console=ttyS0,115200
disL2Cache=yes
disaMvPnp=no
eeeEnable=no
enaAutoRecovery=yes
enaClockGating=yes
enaExtDisk=no
enaFPU=no
enaMonExt=no
enaWrAllo=no
envver=3
eth1addr=E8:FC:AF:E5:34:CB
eth1mtu=1500
ethact=egiga1
ethaddr=E8:FC:AF:E5:34:CA
ethmtu=1500
ethprime=egiga1
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-370-db.dtb
image_name=uImage
initrd_name=uInitrd
load_addr=0x02000000
load_uimage=ext2load usb 0:1 0x800000 /boot/uImage
load_uinitrd=ext2load usb 0:1 0x2100000 /boot/uInitrd
loadaddr=0x02000000
mtdids=nand0=armada-nand
mtdparts=mtdparts=armada-nand:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs)
mvNetConfig=mv_net_config=1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500
mv_pon_addr=00:50:43:00:00:02
nandEcc=1bit
netbsd_en=no
netretry=no
pcieTune=no
pexMode=rc
pxe_files_load=:default.arm-armada370-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
rcvrip=169.254.100.100
sata_delay_reset=0
sata_dma_mode=yes
setL2CacheWT=no
standalone=fsload $load_addr $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm $load_addr;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usb1Mode=host
usb2Mode=device
usbActive=0
usb_boot=mw 0x800000 0 1; run load_uimage; if run load_uinitrd; then bootm 0x800000 0x2100000; else bootm 0x800000; fi
usb_bootcmd=run usb_set_bootargs; run usb_boot
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
Environment size: 2607/131068 bytes
Marvell>> boot
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
** File not found /boot/uImage
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
9488618 bytes read
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
resetting ...
BootROM 1.08
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.4 (COM-PHY-V20)
Update PEX Device ID 0x6710
High speed PHY - Ended Successfully
0000
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run without PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:56:14) Marvell version: v2011.12 2014_T2.0p1
06/23/2015 ReadyNAS-104 V2.0
Board: DB-88F6710-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 200 [MHz]
DDR @ 600 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 512 MiB
Port0: phyAddr=0x0, Not Marvell PHY id1 ffff id2 ffff
PHY error - shutdown port0
Map: Code: 0x1feef000:0x1ff9f514
BSS: 0x1ffef8a0
Stack: 0x1f9eeef8
Heap: 0x1f9ef000:0x1feef000
NAND: (ID 0xf12c) 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Shutting down unused interfaces:
SDIO
AUDIO
TDM
Modules/Interfaces Detected:
RGMII0 Phy
RGMII1 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Net: egiga1 [PRIME]
Warning: egiga1 MAC addresses don't match:
Address in SROM is e8:fc:af:e5:34:cb
Address in environment is e8:fc:af:e5:34:ca
Power On!
FDT loaded successfully
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading /uImage-recovery
** Unable to read "/uImage-recovery" from usb 0:1 **
reading /initrd-recovery.gz
** Unable to read "/initrd-recovery.gz" from usb 0:1 **
NAND read: device 0 offset 0xd4000, size 0x6000
24576 bytes read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Marvell>>
Then.
free -h
total used free shared buff/cache available
Mem: 3.8Gi 854Mi 1.3Gi 157Mi 1.7Gi 2.5Gi
Swap: 3.9Gi 0.0Ki 3.9Gi
And
mount sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,relatime) proc on /proc type proc (rw,nosuid,nodev,noexec,relatime) udev on /dev type devtmpfs (rw,nosuid,relatime,size=1972544k,nr_inodes=184848,mode=755) devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000) tmpfs on /run type tmpfs (rw,nosuid,noexec,relatime,size=397664k,mode=755) /dev/sda6 on / type ext4 (rw,relatime,errors=remount-ro) securityfs on /sys/kernel/security type securityfs (rw,nosuid,nodev,noexec,relatime) tmpfs on /dev/shm type tmpfs (rw,nosuid,nodev) tmpfs on /run/lock type tmpfs (rw,nosuid,nodev,noexec,relatime,size=5120k) tmpfs on /sys/fs/cgroup type tmpfs (ro,nosuid,nodev,noexec,mode=755) cgroup2 on /sys/fs/cgroup/unified type cgroup2 (rw,nosuid,nodev,noexec,relatime,nsdelegate) cgroup on /sys/fs/cgroup/systemd type cgroup (rw,nosuid,nodev,noexec,relatime,xattr,name=systemd) pstore on /sys/fs/pstore type pstore (rw,nosuid,nodev,noexec,relatime) bpf on /sys/fs/bpf type bpf (rw,nosuid,nodev,noexec,relatime,mode=700) cgroup on /sys/fs/cgroup/cpu,cpuacct type cgroup (rw,nosuid,nodev,noexec,relatime,cpu,cpuacct) cgroup on /sys/fs/cgroup/freezer type cgroup (rw,nosuid,nodev,noexec,relatime,freezer) cgroup on /sys/fs/cgroup/memory type cgroup (rw,nosuid,nodev,noexec,relatime,memory) cgroup on /sys/fs/cgroup/rdma type cgroup (rw,nosuid,nodev,noexec,relatime,rdma) cgroup on /sys/fs/cgroup/net_cls,net_prio type cgroup (rw,nosuid,nodev,noexec,relatime,net_cls,net_prio) cgroup on /sys/fs/cgroup/devices type cgroup (rw,nosuid,nodev,noexec,relatime,devices) cgroup on /sys/fs/cgroup/cpuset type cgroup (rw,nosuid,nodev,noexec,relatime,cpuset) cgroup on /sys/fs/cgroup/perf_event type cgroup (rw,nosuid,nodev,noexec,relatime,perf_event) cgroup on /sys/fs/cgroup/pids type cgroup (rw,nosuid,nodev,noexec,relatime,pids) cgroup on /sys/fs/cgroup/blkio type cgroup (rw,nosuid,nodev,noexec,relatime,blkio) systemd-1 on /proc/sys/fs/binfmt_misc type autofs (rw,relatime,fd=33,pgrp=1,timeout=0,minproto=5,maxproto=5,direct,pipe_ino=13323) hugetlbfs on /dev/hugepages type hugetlbfs (rw,relatime,pagesize=2M) debugfs on /sys/kernel/debug type debugfs (rw,relatime) mqueue on /dev/mqueue type mqueue (rw,relatime) fusectl on /sys/fs/fuse/connections type fusectl (rw,relatime) tmpfs on /run/user/0 type tmpfs (rw,nosuid,nodev,relatime,size=397660k,mode=700) gvfsd-fuse on /run/user/0/gvfs type fuse.gvfsd-fuse (rw,nosuid,nodev,relatime,user_id=0,group_id=0) /dev/sda1 on /media/root/6979e70a-644f-45b0-9dcb-a83bbfcc3ae6 type ext4 (rw,nosuid,nodev,relatime,uhelper=udisks2) /dev/sdb1 on /media/root/rootfs type ext3 (rw,nosuid,nodev,relatime,uhelper=udisks2)
And the last one.
ls -lart /media/root/rootfs/boot total 46284 drwxrwxrwx 21 root root 4096 Jan 20 2017 .. -rwxr-xr-x 1 root root 5057632 Aug 19 2019 zImage-5.2.9-mvebu-tld-1 -rwxr-xr-x 1 root root 5057632 Aug 19 2019 zImage -rw-r--r-- 1 root root 183639 Aug 19 2019 config-5.2.9-mvebu-tld-1 -rw------- 1 root root 5057632 Aug 19 2019 vmlinuz-5.2.9-mvebu-tld-1 -rw------- 1 root root 3266081 Aug 19 2019 System.map-5.2.9-mvebu-tld-1 -rw-r--r-- 1 root root 9676808 Aug 19 2019 linux-headers-5.2.9-mvebu-tld-1_1.0_armhf.deb drwxr-xr-x 2 root root 4096 Aug 19 2019 dts -rw-r--r-- 1 root root 9488554 Aug 26 2019 initrd.img-5.2.9-mvebu-tld-1 -rw-r--r-- 1 root root 9488618 Aug 26 2019 uInitrd drwxr-xr-x 3 root root 4096 Sep 5 2019 .
Yes and when i look into the mapps / file system then the USB drive have the name
rootfs
And dir look like this.
/media/root/rootfs(/dev/sdb1)
Yes then i have it.
Thanks again.
AkkJaa...
|
Re: RN10400 February 06, 2021 06:12PM |
Admin Registered: 13 years ago Posts: 18,548 |
AkkJaa,
And the last one.
You have accidentally remove the uImage file from /boot directory.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
/dev/sdb1 on /media/root/rootfs type ext3 (rw,nosuid,nodev,relatime,uhelper=udisks2)
And the last one.
ls -lart /media/root/rootfs/boot total 46284 drwxrwxrwx 21 root root 4096 Jan 20 2017 .. -rwxr-xr-x 1 root root 5057632 Aug 19 2019 zImage-5.2.9-mvebu-tld-1 -rwxr-xr-x 1 root root 5057632 Aug 19 2019 zImage -rw-r--r-- 1 root root 183639 Aug 19 2019 config-5.2.9-mvebu-tld-1 -rw------- 1 root root 5057632 Aug 19 2019 vmlinuz-5.2.9-mvebu-tld-1 -rw------- 1 root root 3266081 Aug 19 2019 System.map-5.2.9-mvebu-tld-1 -rw-r--r-- 1 root root 9676808 Aug 19 2019 linux-headers-5.2.9-mvebu-tld-1_1.0_armhf.deb drwxr-xr-x 2 root root 4096 Aug 19 2019 dts -rw-r--r-- 1 root root 9488554 Aug 26 2019 initrd.img-5.2.9-mvebu-tld-1 -rw-r--r-- 1 root root 9488618 Aug 26 2019 uInitrd drwxr-xr-x 3 root root 4096 Sep 5 2019 .
You have accidentally remove the uImage file from /boot directory.
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: RN10400 February 07, 2021 02:05PM |
Registered: 3 years ago Posts: 116 |
Hi Bodhi,
Here i have make a new USB Drive. Now i use fdisk and delete the old partion and make a new pri partion then i format it with this
Yes and now, can you see something i have did wrong.?? Is there posible to move the ulmage file to the boot dir.?? or is it right now. i see it is more with now or.
Thanks Again.
AkkJaa...
Here i have make a new USB Drive. Now i use fdisk and delete the old partion and make a new pri partion then i format it with this
mkfs.ext3 -L rootfs /dev/sdb1And
cd /media/root/rootfs tar -xjf Debian-5.2.9-mvebu-tld-1-rootfs-bodhi.tar.bz2 sync syncBut i can't see it sync. Well then i did this
umount /media/root/rootfsSo then i take it over to the RN104 motherboard and turn on and then this.
Terminal ready
BootROM 1.08
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.4 (COM-PHY-V20)
Update PEX Device ID 0x6710
High speed PHY - Ended Successfully
0001
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run without PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:56:14) Marvell version: v2011.12 2014_T2.0p1
06/23/2015 ReadyNAS-104 V2.0
Board: DB-88F6710-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 200 [MHz]
DDR @ 600 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 512 MiB
Port0: phyAddr=0x0, Not Marvell PHY id1 ffff id2 ffff
PHY error - shutdown port0
Map: Code: 0x1feef000:0x1ff9f514
BSS: 0x1ffef8a0
Stack: 0x1f9eeef8
Heap: 0x1f9ef000:0x1feef000
NAND: (ID 0xf12c) 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Shutting down unused interfaces:
SDIO
AUDIO
TDM
Modules/Interfaces Detected:
RGMII0 Phy
RGMII1 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Net: egiga1 [PRIME]
Warning: egiga1 MAC addresses don't match:
Address in SROM is e8:fc:af:e5:34:cb
Address in environment is e8:fc:af:e5:34:ca
Power On!
FDT loaded successfully
Hit any key to stop autoboot: 0
Marvell>> setenv usb_set_bootargs 'setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial'
Marvell>> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
Marvell>> setenv load_uinitrd 'ext2load usb 0:1 0x2100000 /boot/uInitrd'
Marvell>> setenv usb_boot 'mw 0x800000 0 1; run load_uimage; if run load_uinitrd; then bootm 0x800000 0x2100000; else bootm 0x800000; fi'
Marvell>> setenv usb_bootcmd 'run usb_set_bootargs; run usb_boot'
Marvell>> setenv bootcmd 'usb start; run usb_bootcmd; usb stop; reset'
Marvell>> printenv
AC_Power_fail_detect=open
CASset=min
HW_version=MVT
MALLOC_len=5
Manufacturer=NETGEAR
Product=ReadyNAS 104
SKUNum=RN104
SerialNum=3EPE51EM006E2
Startup=Normal
UUID=8ad06a7e-97fc-11e4-9cf7-e8fcafe534ca
Version=V1.0
autoload=no
bootargs=console=ttyS0,115200
bootargs_end=:10.4.50.254:255.255.255.0:KW40:eth0:none
bootargs_root=root=/dev/nfs rw
bootcmd=usb start; run usb_bootcmd; usb stop; reset
bootcmd_fdt=tftpboot 0x2000000 $image_name;tftpboot $fdtaddr $fdtfile;setenv bootargs $console $mtdparts $bootargs_root nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip$bootargs_end $mvNetConfig video=dovefb:lcd0:$lcd0_params clcd.lcd0_enable=$lcd0_enable clcd.lcd_panel=$lcd_panel; bootz 0x2000000 - $fdtaddr;
bootcmd_ubi=ubi part ubifs; ubifsmount rootfs; ubifsload 0x2000000 kernel; ubifsload 0x3000000 initrd.gz; bootm 0x2000000 0x3000000 0x1000000
bootdelay=0
cacheShare=no
console=console=ttyS0,115200
disL2Cache=yes
disaMvPnp=no
eeeEnable=no
enaAutoRecovery=yes
enaClockGating=yes
enaExtDisk=no
enaFPU=no
enaMonExt=no
enaWrAllo=no
envver=3
eth1addr=E8:FC:AF:E5:34:CB
eth1mtu=1500
ethact=egiga1
ethaddr=E8:FC:AF:E5:34:CA
ethmtu=1500
ethprime=egiga1
fdt_skip_update=no
fdtaddr=0x1000000
fdtfile=armada-370-db.dtb
image_name=uImage
initrd_name=uInitrd
load_addr=0x02000000
load_uimage=ext2load usb 0:1 0x800000 /boot/uImage
load_uinitrd=ext2load usb 0:1 0x2100000 /boot/uInitrd
loadaddr=0x02000000
mtdids=nand0=armada-nand
mtdparts=mtdparts=armada-nand:0x180000@0(u-boot),0x20000@0x180000(u-boot-env),0x600000@0x200000(uImage),0x400000@0x800000(minirootfs),-(ubifs)
mvNetConfig=mv_net_config=1,(00:50:43:11:11:11,0:1:2:3:4),mtu=1500
mv_pon_addr=00:50:43:00:00:02
nandEcc=1bit
netbsd_en=no
netretry=no
pcieTune=no
pexMode=rc
pxe_files_load=:default.arm-armada370-db:default.arm-armadaxp:default.arm
pxefile_addr_r=3100000
rcvrip=169.254.100.100
sata_delay_reset=0
sata_dma_mode=yes
setL2CacheWT=no
standalone=fsload $load_addr $image_name;setenv bootargs $console $mtdparts root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end; bootm $load_addr;
stderr=serial
stdin=serial
stdout=serial
usb0Mode=host
usb1Mode=host
usb2Mode=device
usbActive=0
usb_boot=mw 0x800000 0 1; run load_uimage; if run load_uinitrd; then bootm 0x800000 0x2100000; else bootm 0x800000; fi
usb_bootcmd=run usb_set_bootargs; run usb_boot
usb_set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 earlyprintk=serial
vxworks_en=no
yuk_ethaddr=00:00:00:EE:51:81
Environment size: 2607/131068 bytes
Marvell>> boot
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
** File not found /boot/uImage
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
9488618 bytes read
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
resetting ...
BootROM 1.08
Booting from NAND flash
General initialization - Version: 1.0.0
High speed PHY - Version: 2.1.4 (COM-PHY-V20)
Update PEX Device ID 0x6710
High speed PHY - Ended Successfully
0000
DDR3 Training Sequence - Ver 5.7.1
DDR3 Training Sequence - Run without PBS.
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-gec25d27-dirty (Oct 26 2015 - 16:56:14) Marvell version: v2011.12 2014_T2.0p1
06/23/2015 ReadyNAS-104 V2.0
Board: DB-88F6710-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 200 [MHz]
DDR @ 600 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 512 MiB
Port0: phyAddr=0x0, Not Marvell PHY id1 ffff id2 ffff
PHY error - shutdown port0
Map: Code: 0x1feef000:0x1ff9f514
BSS: 0x1ffef8a0
Stack: 0x1f9eeef8
Heap: 0x1f9ef000:0x1feef000
NAND: (ID 0xf12c) 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Initialize and scan all PCI interfaces
PEX unit.port(active IF[-first bus]):
------------------------------------------
PEX 0: Root Complex Interface, Detected Link X1, GEN 2.0
PEX 1: Root Complex Interface, Detected Link X1, GEN 2.0
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Shutting down unused interfaces:
SDIO
AUDIO
TDM
Modules/Interfaces Detected:
RGMII0 Phy
RGMII1 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Net: egiga1 [PRIME]
Warning: egiga1 MAC addresses don't match:
Address in SROM is e8:fc:af:e5:34:cb
Address in environment is e8:fc:af:e5:34:ca
Power On!
FDT loaded successfully
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Active port: 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading /uImage-recovery
** Unable to read "/uImage-recovery" from usb 0:1 **
reading /initrd-recovery.gz
** Unable to read "/initrd-recovery.gz" from usb 0:1 **
NAND read: device 0 offset 0xd4000, size 0x6000
24576 bytes read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Marvell>>
Then this.
free -h
total used free shared buff/cache available
Mem: 3.8Gi 774Mi 1.6Gi 144Mi 1.5Gi 2.5Gi
Swap: 3.9Gi 0B 3.9Gi
And.
mount sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,relatime) proc on /proc type proc (rw,nosuid,nodev,noexec,relatime) udev on /dev type devtmpfs (rw,nosuid,relatime,size=1972512k,nr_inodes=184832,mode=755) devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000) tmpfs on /run type tmpfs (rw,nosuid,noexec,relatime,size=397660k,mode=755) /dev/sda6 on / type ext4 (rw,relatime,errors=remount-ro) securityfs on /sys/kernel/security type securityfs (rw,nosuid,nodev,noexec,relatime) tmpfs on /dev/shm type tmpfs (rw,nosuid,nodev) tmpfs on /run/lock type tmpfs (rw,nosuid,nodev,noexec,relatime,size=5120k) tmpfs on /sys/fs/cgroup type tmpfs (ro,nosuid,nodev,noexec,mode=755) cgroup2 on /sys/fs/cgroup/unified type cgroup2 (rw,nosuid,nodev,noexec,relatime,nsdelegate) cgroup on /sys/fs/cgroup/systemd type cgroup (rw,nosuid,nodev,noexec,relatime,xattr,name=systemd) pstore on /sys/fs/pstore type pstore (rw,nosuid,nodev,noexec,relatime) bpf on /sys/fs/bpf type bpf (rw,nosuid,nodev,noexec,relatime,mode=700) cgroup on /sys/fs/cgroup/blkio type cgroup (rw,nosuid,nodev,noexec,relatime,blkio) cgroup on /sys/fs/cgroup/devices type cgroup (rw,nosuid,nodev,noexec,relatime,devices) cgroup on /sys/fs/cgroup/rdma type cgroup (rw,nosuid,nodev,noexec,relatime,rdma) cgroup on /sys/fs/cgroup/memory type cgroup (rw,nosuid,nodev,noexec,relatime,memory) cgroup on /sys/fs/cgroup/net_cls,net_prio type cgroup (rw,nosuid,nodev,noexec,relatime,net_cls,net_prio) cgroup on /sys/fs/cgroup/cpuset type cgroup (rw,nosuid,nodev,noexec,relatime,cpuset) cgroup on /sys/fs/cgroup/cpu,cpuacct type cgroup (rw,nosuid,nodev,noexec,relatime,cpu,cpuacct) cgroup on /sys/fs/cgroup/freezer type cgroup (rw,nosuid,nodev,noexec,relatime,freezer) cgroup on /sys/fs/cgroup/pids type cgroup (rw,nosuid,nodev,noexec,relatime,pids) cgroup on /sys/fs/cgroup/perf_event type cgroup (rw,nosuid,nodev,noexec,relatime,perf_event) systemd-1 on /proc/sys/fs/binfmt_misc type autofs (rw,relatime,fd=30,pgrp=1,timeout=0,minproto=5,maxproto=5,direct,pipe_ino=13239) mqueue on /dev/mqueue type mqueue (rw,relatime) debugfs on /sys/kernel/debug type debugfs (rw,relatime) hugetlbfs on /dev/hugepages type hugetlbfs (rw,relatime,pagesize=2M) fusectl on /sys/fs/fuse/connections type fusectl (rw,relatime) tmpfs on /run/user/0 type tmpfs (rw,nosuid,nodev,relatime,size=397656k,mode=700) gvfsd-fuse on /run/user/0/gvfs type fuse.gvfsd-fuse (rw,nosuid,nodev,relatime,user_id=0,group_id=0) /dev/sda1 on /media/root/6979e70a-644f-45b0-9dcb-a83bbfcc3ae6 type ext4 (rw,nosuid,nodev,relatime,uhelper=udisks2) /dev/sdb1 on /media/root/rootfs type ext3 (rw,nosuid,nodev,relatime,uhelper=udisks2)And the last one.
ls -lart /media/root/rootfs total 263944 drwxr-xr-x 2 root root 4096 Apr 6 2015 sys drwxr-xr-x 2 root root 4096 Sep 12 2016 proc drwxr-xr-x 2 root root 4096 Sep 12 2016 home drwxr-xr-x 2 root root 4096 Jan 2 2017 srv drwxr-xr-x 2 root root 4096 Jan 2 2017 opt drwxr-xr-x 2 root root 4096 Jan 2 2017 mnt drwxr-xr-x 11 root root 4096 Jan 2 2017 var drwxr-xr-x 10 root root 4096 Jan 2 2017 usr drwxr-xr-x 4 root root 4096 Jan 2 2017 dev drwx------ 2 root root 16384 Jan 9 2017 lost+found drwxrwxrwx 21 root root 4096 Jan 20 2017 . drwxr-xr-x 2 root root 4096 Jan 20 2017 media drwxr-xr-x 8 root root 4096 Aug 25 2019 run drwxr-xr-x 13 root root 4096 Aug 26 2019 lib drwxr-xr-x 2 root root 4096 Aug 26 2019 bin drwxr-xr-x 2 root root 4096 Aug 26 2019 sbin drwxrwxrwt 2 root root 4096 Sep 5 2019 tmp drwxr-xr-x 70 root root 4096 Sep 5 2019 etc drwxr-xr-x 3 root root 4096 Sep 5 2019 boot drwx------ 5 root root 4096 Sep 10 2019 root -rw-r--r-- 1 root root 269907402 Jan 24 23:05 Debian-5.2.9-mvebu-tld-1-rootfs-bodhi.tar.bz2 drwxr-x---+ 4 root root 4096 Feb 7 20:43 ..
Yes and now, can you see something i have did wrong.?? Is there posible to move the ulmage file to the boot dir.?? or is it right now. i see it is more with now or.
Thanks Again.
AkkJaa...
|
Re: RN10400 February 07, 2021 03:47PM |
Admin Registered: 13 years ago Posts: 18,548 |
AkkJaa,
The sync if successful will not output anything. Just a way to commit any pending writes to the all disk drives in the system, including the USB. This is a precaution only.
At this point cd to the rootfs boot folder and check the boot files
You should see the zImage-5.2.9-mvebu-tld-1 and uInitrd that came with rootfs. And then you need to continue with Step 3 as instructed in the rootfs creation (you just did Step 2).
https://forum.doozan.com/read.php?2,32146
Note the armada-380-zyxel-nas326.dtb above, it needs to be replaced with the DTB for this box.
armada-370-netgear-rn104.dtb
So adjust for your box at this time Step 3 should be:
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
> cd /media/root/rootfs > tar -xjf > Debian-5.2.9-mvebu-tld-1-rootfs-bodhi.tar.bz2 > sync > sync >> But i can't see it sync.
The sync if successful will not output anything. Just a way to commit any pending writes to the all disk drives in the system, including the USB. This is a precaution only.
At this point cd to the rootfs boot folder and check the boot files
cd /media/root/rootfs/boot ls -lart
You should see the zImage-5.2.9-mvebu-tld-1 and uInitrd that came with rootfs. And then you need to continue with Step 3 as instructed in the rootfs creation (you just did Step 2).
https://forum.doozan.com/read.php?2,32146
Quote
3. Create uImage with DTB appended. I am using the Zyxel NAS326 as an example here. Please replace armada-380-zyxel-nas326.dtb below with the appropriate DTB name for your box.
cd /media/sdb1/boot
cp -a zImage-5.2.9-mvebu-tld-1 zImage.fdt
cat dts/armada-380-zyxel-nas326.dtb >> zImage.fdt
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-5.2.9-mvebu-tld-1 -d zImage.fdt uImage
Note the armada-380-zyxel-nas326.dtb above, it needs to be replaced with the DTB for this box.
armada-370-netgear-rn104.dtb
So adjust for your box at this time Step 3 should be:
cd /media/root/rootfs/boot cp -a zImage-5.2.9-mvebu-tld-1 zImage.fdt cat dts/armada-370-netgear-rn104.dtb >> zImage.fdt mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-5.2.9-mvebu-tld-1 -d zImage.fdt uImage sync
-bodhi
===========================
Forum Wiki
bodhi's corner (buy bodhi a beer)
|
Re: RN10400 February 07, 2021 05:19PM |
Registered: 3 years ago Posts: 116 |
Hi Bodhi,
Yes ok, now i did this
Then step 3. Well i will try.
Thanks Again.
AkkJaa...
Yes ok, now i did this
cd /media/root/rootfs/bootThen this.
ls -lart total 46292 drwxrwxrwx 21 root root 4096 Jan 20 2017 .. -rwxr-xr-x 1 root root 5057632 Aug 19 2019 zImage-5.2.9-mvebu-tld-1 -rwxr-xr-x 1 root root 5057632 Aug 19 2019 zImage -rw-r--r-- 1 root root 183639 Aug 19 2019 config-5.2.9-mvebu-tld-1 -rw------- 1 root root 5057632 Aug 19 2019 vmlinuz-5.2.9-mvebu-tld-1 -rw------- 1 root root 3266081 Aug 19 2019 System.map-5.2.9-mvebu-tld-1 -rw-r--r-- 1 root root 9676808 Aug 19 2019 linux-headers-5.2.9-mvebu-tld-1_1.0_armhf.deb drwxr-xr-x 2 root root 4096 Aug 19 2019 dts drwxr-xr-x 7 root root 4096 Aug 26 2019 initrd.img-5.2 drwxr-xr-x 7 root root 4096 Aug 26 2019 'initrd.img-5 (1).2' -rw-r--r-- 1 root root 9488554 Aug 26 2019 initrd.img-5.2.9-mvebu-tld-1 -rw-r--r-- 1 root root 9488618 Aug 26 2019 uInitrd drwxr-xr-x 5 root root 4096 Feb 7 23:32 .Oky Doki,
Then step 3. Well i will try.
Thanks Again.
AkkJaa...
|
Re: RN10400 March 02, 2021 05:38PM |
Registered: 3 years ago Posts: 116 |
|
Re: RN10400 March 03, 2021 01:17PM |
Registered: 3 years ago Posts: 116 |
Bodhi,
Now i work with part 3. but here is a command who is not here.
And i try just the command but the same.
And i can't find the file.: armada-370-netgear-rn104.dtb but i had the file.: armada370-netgear-rn102.dtb so i used that one.
Then the file.: zimage-5.2.9-mvebu-tld-1 come with the first command.
Thanks Again.
Best regards.
AkkJaa...
Now i work with part 3. but here is a command who is not here.
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-5.2.9-mvebu-tld-1 -d zImage.fdt uImage bash: mkimage: command not found
And i try just the command but the same.
mkimage bash: mkimage: command not found
And i can't find the file.: armada-370-netgear-rn104.dtb but i had the file.: armada370-netgear-rn102.dtb so i used that one.
Then the file.: zimage-5.2.9-mvebu-tld-1 come with the first command.
cp -a zImage-5.2.9-mvebu-tld-1 zImage.fdtAnd this
cat dts/armada-370-netgear-rn102.dtb >> zImage.fdtThis is in this dir
/media/root/rootfs/boot#Yes then i think i have with most of it.
Thanks Again.
Best regards.
AkkJaa...
